Agilent 34410A and 34411A Multimeters

Agilent 34410A and 34411A Multimeters
Agilent 34410A and 34411A Multimeters
Data Sheet
See Agilent's Truevolt Series of DMMs
• Display DMM results in ways you never have before
• Measure with unquestioned Truevolt confidence
• Move to the next generation 34401A DMM with 100% assurance
www.agilent.com/find/dmm
Agilent 34410A 61/2-Digit
High-Performance DMM
• 10,000 readings/s @ 5 1/2 -digits
direct to PC
• 1,000 readings/s @ 6 1/2 -digits
direct to PC
• 30 PPM 1-year Basic DC accuracy
• LAN, USB & GPIB standard
• DCV, ACV, DCI, ACI, 2-wire and
4-wire Resistance, Frequency,
Period, Continuity, and Diode Test
• Capacitance & Temperature
measurements
• Expanded measurement ranges
• Data logger with 50 k reading
non-volatile memory
Agilent 34411A 61/2-Digit
Enhanced-Performance DMM
All the features of the 34410A, plus:
• 50,000 readings/s @ 41/2 -digits
direct to PC
• 1 million volatile reading memory
• Analog level triggering
• Programmable Pre/Post triggering
The Best Just Got Better
The Agilent 34410A and 34411A
61/2-Digit DMMs represent the latest generation of multimeters from
Agilent Technologies. Building on the
phenomenal success of the industrystandard Agilent 34401A, these new
meters offer improved accuracy,
expanded measurement capability,
dramatically improved measurement
speed and throughput, and modern
computer interfaces including LAN
and USB. The dual display offers
both dual measurement capabilities
and ease of use when setting up and
configuring the DMM. Improvements
have been made in every facet of the
34401A to make the best even better, whether you use it on the bench
or in a system.
Dramatic Speed Improvements
Whether it’s raw reading speed or
fast system throughput, the 34410A
sets a new benchmark in performance. Using a new A/D technology,
the 34410A achieves an impressive
10,000 readings a second at 51/2-digits, and can stream readings to
your computer at this same speed!
Triggering is fast and precise, with
both trigger latency and trigger jit-
ter less than 1 µs, while bus query
response is less than 500 µs. ACV
measurements are faster as well
thanks to a digital measurement
technique that additionally improves
accuracy at high and low frequencies. For even greater reading speeds,
select the 34411A, which achieves
50,000 readings a second at 41/2-digits.
Enhanced Measurement Performance
The 34410A and 34411A offer
Temperature and Capacitance
capabilities, in addition to those measurements you have come to expect,
such as DCV, ACV, DCI, ACI, 2-wire
and 4-wire Resistance, Frequency,
Period, Continuity and Diode Test.
You also get Offset Compensated
Ohms, allowing you to accurately
measure resistance in the presence of
voltages. Measurement ranges have
been expanded as well; for example,
DC and AC Current Ranges now go
down to 100 µA, resulting in 100
pA resolution. Real-time math and
statistics are included, and a peakdetect capability allows you to capture peaks as short as 20 µs.
Even Greater Performance
with the 34411A
The 34411A has all the features
of the 34410A, plus additional
performance that makes it even
more powerful. With the ability to
make 50,000 readings per second at
41/2 -digits, Analog Level Triggering,
programmable Pre- and Post-Trigger
and 1 million readings of volatile
memory in addition to 50,000
reading of non-volatile memory,
you now have the ability to capture low-frequency waveforms,
characterize device performance
and transfer results for analysis on
your computer.
Data Logger Function
A front panel data logger function
allows you to set the meter up to
make unattended, paced measurements over a fixed time or number
of events, then pull up the results
later for review or transfer to a
computer for analysis. Set the
meter up to take measurements
every 10 seconds for an hour, go
have lunch, and check the results
upon your return. The contextual
front panel sequences make setup
and read back a breeze.
Improved Ease of Use
From the inclusion of a second
display to configuring setups for
each of the measurement functions,
these new DMMs offer significant
improvements in usability. Simple
things are simple; more complicated
setups are easier than ever. There
is even a new probe set designed
to more easily probe today’s finepitch components. Finally, there is
a built-in Graphical Web Interface
that allows you to interactively
control the DMM without the
hassle of programming at all!
Modern I/O for Improved Connectivity
When connecting to a computer,
select LAN, USB or GPIB interfaces; all three are standard on the
34410A and 34411A. Concerned
about the viability of your existing
software programs? These new DMMs
respond to Standard Commands
for Programmable Instrumentation
(SCPI), and there is even a 34401A
Emulation Mode to ensure the
easiest upgrade possible. Agilent’s
I/O Library Suite ships with the
34410A and 34411A to help you
quickly establish an error-free
connection between your PC and
instrument. It provides robust
instrument control and works
with the software development
environment you choose.
Product Reference CD-ROM with
soft documentation and software:
LXI – Class C
LAN Extensions for Instruments (LXI)
provides the next generation I/O
for system applications requiring
the highest throughput. Transfer
rates of over 250,000 readings/s are
attainable ensuring even the most
data intensive measurements are
fast, without the overhead cost
of an instrument cardcage. Both
the 34410A and the 34411A are
LXI – Class C compliant.
Bench Dimensions:
Built To Last
Our new DMMs were designed
to high standards of ruggedness
and reliability. From the robust
package with its shock absorbing
bumpers to careful selection of
components and conservative
circuit design, these meters are
built to last. Calculated Mean
Time Between Failure (MTBF) is in
excess of 100,000 hours. Backed by
a 1-year warranty and a worldwide
network of service centers, you can
buy with confidence.
•
•
•
•
•
•
•
Optional Printed Documentation:
• Quick Start Tutorial
• User’s Guide
• Service Guide
261.2 mm
103.8 mm
303.2 mm
System Dimensions:
Go to the Web
For the latest information on
these or other Agilent DMMs,
go to www.agilent.com/find/dmm
Accessories Included:
• Test Lead Kit with probes
and SMT attachments.
• Test report, power cord,
and USB interface cable.
Programmer’s Reference Help
Quick Start Tutorial
User’s Guide
Service Guide
Programming Examples
IntuiLink for Multimeters
LabVIEW and IVI-COM drivers
212.8 mm
88.3 mm
272.3 mm
2
Accuracy Specifications ± (% of reading + % of range)1
Function
Range 3
Frequency,
24 Hour 2
90 Day
1 Year
Temperature
Test Current or
Burden Voltage
Tcal ± 1 °C
Tcal ± 5 °C
Tcal ± 5 °C
0 °C to (Tcal -5 °C)
(Tcal +5 °C) to 55 °C
0.0005 + 0.0005
0.0005 + 0.0001
0.0005 + 0.0001
0.0005 + 0.0001
0.0005 + 0.0001
0.010 + 0.003
0.008 + 0.003
0.005 + 0.003
0.010 + 0.005
0.020 + 0.008
0.120 + 0.020
0.0006 + 0.0005
0.0006 + 0.0001
0.0006 + 0.0001
0.0006 + 0.0001
0.0010 + 0.0002
0.0030 + 0.0004
0.1000 + 0.0001
1.0000 + 0.0001
0.0020 + 0.0030
0.0020 + 0.0005
0.0020 + 0.0020
0.0020 + 0.0005
0.0050 + 0.0010
0.0050 + 0.0020
0.015 + 0.006
0.030 + 0.006
0.005 + 0.000
0.005 + 0.000
0.001 + 0.000
0.001 + 0.000
0.05 + 0.05
0.05 + 0.01
0.01 + 0.01
0.01 + 0.01
0.01 + 0.01
Coefficient/°C
DC Voltage
True RMS
AC Voltage5
Resistance6
DC Current
True RMS
AC Current 7
Frequency
or Period
Capacitance8
100.0000 mV
1.000000 V
10.00000 V
100.0000 V
1000.000 V 4
100.0000 mV
to 750.000 V
100.0000 Ω
1.000000 kΩ
10.00000 kΩ
100.0000 kΩ
1.000000 MΩ
10.00000 MΩ
100.0000 MΩ
1.000000 GΩ
100.0000 µA
1.000000 mA
10.00000 mA
100.0000 mA
1.000000 A
3.000000 A
100.0000 µA to
3.00000 A
100 mV to
750 V
1.0000 nF
10.000 nF
100.00 nF
1.0000 µF
10.000 µF
Temperature9
RTD
Thermistor
Continuity
-200 °C to 600 °C
-80 °C to 150 °C
1000.0 Ω
Diode Test10
1.0000 V
3 Hz – 5 Hz
5 Hz – 10 Hz
10 Hz – 20 kHz
20 kHz – 50 kHz
50 kHz – 100 kHz
100 kHz – 300 kHz
1 mA
1 mA
100 µA
10 µA
5 µA
500 nA
500 nA || 10 MΩ
500 nA || 10 MΩ
< 0.03 V
< 0.3 V
< 0.03 V
< 0.3 V
< 0.8 V
< 2.0 V
3 Hz – 5 kHz
5 kHz – 10 kHz
3 Hz – 5 Hz
5 Hz – 10 Hz
10 Hz – 40 Hz
40 Hz – 300 kHz
500 nA
1 µA
10 µA
10 µA
100 µA
1 mA
1 mA
0.0030 + 0.0030
0.0020 + 0.0006
0.0015 + 0.0004
0.0020 + 0.0006
0.0020 + 0.0006
0.50 + 0.02
0.10 + 0.02
0.02 + 0.02
0.05 + 0.04
0.20 + 0.08
1.00 + 0.50
0.0030 + 0.0030
0.0020 + 0.0005
0.0020 + 0.0005
0.0020 + 0.0005
0.0020 + 0.0010
0.0100 + 0.0010
0.200 + 0.001
2.000 + 0.001
0.010 + 0.020
0.007 + 0.006
0.007 + 0.020
0.010 + 0.004
0.050 + 0.006
0.100 + 0.020
0.10 + 0.04
0.20 + 0.04
0.070 + 0.000
0.040 + 0.000
0.020 + 0.000
0.005 + 0.000
0.50 + 0.50
0.40 + 0.10
0.40 + 0.10
0.40 + 0.10
0.40 + 0.10
0.0040 + 0.0035
0.0030 + 0.0007
0.0020 + 0.0005
0.0035 + 0.0006
0.0035 + 0.0006
0.50 + 0.03
0.10 + 0.03
0.05 + 0.03
0.09 + 0.05
0.30 + 0.08
1.20 + 0.50
0.008 + 0.004
0.007 + 0.001
0.007 + 0.001
0.007 + 0.001
0.010 + 0.001
0.030 + 0.001
0.600 + 0.001
6.000 + 0.001
0.040 + 0.025
0.030 + 0.006
0.030 + 0.020
0.030 + 0.005
0.080 + 0.010
0.120 + 0.020
0.10 + 0.04
0.20 + 0.04
0.070 + 0.000
0.040 + 0.000
0.020 + 0.000
0.006 + 0.000
0.50 + 0.50
0.40 + 0.10
0.40 + 0.10
0.40 + 0.10
0.40 + 0.10
0.0050 + 0.0035
0.0035 + 0.0007
0.0030 + 0.0005
0.0040 + 0.0006
0.0040 + 0.0006
0.50 + 0.03
0.10 + 0.03
0.06 + 0.03
0.10 + 0.05
0.40 + 0.08
1.20 + 0.50
0.010 + 0.004
0.010 + 0.001
0.010 + 0.001
0.010 + 0.001
0.012 + 0.001
0.040 + 0.001
0.800 + 0.001
8.000 + 0.001
0.050 + 0.025
0.050 + 0.006
0.050 + 0.020
0.050 + 0.005
0.100 + 0.010
0.150 + 0.020
0.10 + 0.04
0.20 + 0.04
0.070 + 0.000
0.040 + 0.000
0.020 + 0.000
0.007 + 0.000
0.50 + 0.50
0.40 + 0.10
0.40 + 0.10
0.40 + 0.10
0.40 + 0.10
0.06 °C
0.08 °C
0.06 °C
0.08 °C
0.06 °C
0.08 °C
0.003 °C
0.002 °C
0.002 + 0.010
0.002 + 0.010
0.008 + 0.020
0.008 + 0.020
0.010 + 0.020
0.010 + 0.020
0.0010 + 0.0020
0.0010 + 0.0020
1
2
3
4
5
Specifications are for 90 minute warm-up and 100 PLC.
Relative to calibration standards.
20% overrange on all ranges, except DCV 1000 V, ACV 750 V, DCI and ACI 3 A ranges.
For each additional volt over ± 500 V add 0.02 mV of error.
Specifications are for sinewave input > 0.3% of range and > 1 mVrms. Add 30 µV error for frequencies below 1 kHz.
750 VAC range limited to 8 x 10 7 Volts-Hz. For each additional volt over 300 Vrms add 0.7 mVrms of error.
6 Specifications are for 4-wire resistance measurements, or 2-wire using Math Null.
Without Math Null, add 0.2 Ω additional error in 2-wire resistance measurements.
7 Specifications are for sinewave input > 1% of range and > 10 µArms. Frequencies > 5 kHz are typical
for all ranges. For the 3 A range (all frequencies) add 0.05% of reading + 0.02% of range to listed specifications.
8 Specifications are for 1-hour warm-up using Math Null. Additional errors may occur for non-film capacitors.
9 For total measurement accuracy, add temperature probe error.
10 Accuracy specifications are for the voltage measured at the input terminals only. 1 mA test current is typical.
Variation in the current source will create some variation in the voltage drop across a diode junction.
3
A-to-D Converter Noise Performance
1
2
3
4
5
Resolution
(ppm of range)1
Normal Mode
Rejection (dB)2
Readings/Second4
0.0015
0.002 5
0.006
0.02
0.06
0.2
1
2
10
100
30
15
6
3
1.5
0.7
0.3
0.2
0.1
0.03
0
0
0
0
0
0
55
110 3
110 3
110 3
50,000
25,000
10,000
3,000
1,000
300
60 (50)
30 (25)
6 (5)
0.6 (0.5)
100
RMS Noise (ppm of range)
Integration Time
(NPLC)
10
1
0.1
0.01
0.001
0.01
0.1
1
10
Integration Time (NPLC)
Resolution is defined as the typical DCV 10 V range RMS noise.
Auto-zero on for NPLC ≥ 1. See manual for additional noise characteristics.
Normal mode rejection for power line frequency ± 0.1%.
For power-line frequency ± 1% 75 dB and for ± 3% 55 dB.
Maximum rate with auto-zero off for 60 Hz and (50 Hz) operation.
Only available for the 34411A.
System Reading and Throughput Rates
System Reading Architecture
DMM memory to PC (Maximum reading rate out of memory)1
Drawing – Path B
Reading
Format
ASCII
32-bit Binary
64-bit Binary
GPIB
Readings/s
USB 2.0
Readings/s
4,000
89,000
47,000
8,500
265,000
154,000
LAN (VXI-11)
Readings/s
LAN (Sockets)
Readings/s
7,000
110,000
60,000
8,500
270,000
160,000
Direct I/O Measurements (Single reading – measure and I/O time)1
Drawing – Path C
Function
DCV/2-wire
Resistance
ACV/
Frequency
1
Maximum Reading
Rate into Memory
or to Direct I/O
Resolution
(NPLC)
GPIB
ms
USB 2.0
ms
LAN
(VXI-11)
ms
LAN
(Sockets)
ms
0.006 (0.001)
2.6
2.9
4.6
3.2
10,000 (50,000)
Fast Filter
1 ms Gate
10.0
10.0
10.0
10.0
500
(Readings/s)
Drawing – Path A or C
1/2 scale input signal, immediate trigger, trigger delay 0, auto-zero off, auto-range off, no math, null off,
60 Hz line frequency. Specifications are for 34410A or (34411A). See manual for performance on other functions.
System Performance
Function
Change (ms)1
Range
Change (ms)2
LAN/GPIB
Autorange (ms)3
Maximum
External
Trigger Rate
Maximum Internal
Trigger Rate4
DCV/2-wire
Resistance
22
3.9/2.6
7.5
5,000/s
10,000/s
(50,000/s)
ACV/
Frequency
37
6.5/6.4
19
500/s
500/s
1
Time to change from 2-wire Resistance to this specified function,
or DCV to 2-wire Resistance using the SCPI “FUNC” command.
2
Time to change from one range to the next higher range, ≤ 10 V, ≤ 10 MΩ.
3
Time to automatically change one range and be ready for the new measurement, ≤ 10 V, ≤ 10 MΩ.
4
Specifications are for 34410A or (34411A).
4
100
Measurement Characteristics
DC Voltage
True RMS AC Current
Additional 34411A Specifications
Measurement Method:
Continuously integrating
multi-slope IV A/D converter
Measurement Method:
AC-coupled True RMS measurement.
Directly coupled to the fuse and shunt.
Digital sampling with anti-alias filter.
Resolution: See table on page 4
Linearity:
(10 V range)
0.0002% of reading
+ 0.0001% of range
Input Resistance:
0.1 V, 1 V, 10 V
Ranges
100 V, 1000 V
Ranges
10 MΩ or > 10 GΩ
(Selectable)
10 MΩ ± 1%
(Fixed)
Current Shunt:
200 Ω for 100 µA, 1 mA
2 Ω for 10 mA, 100 mA
0.1 Ω for 1 A, 3 A
Trigger Jitter:
2 µs (p-p), 20 µs (p-p) when pre-triggered
Input Bias Current: < 50 pA at 25 °C
Input Protection: 1000 V
Input Protection: 3 A, 250 V fuse
140 dB1
Frequency and Period
True RMS AC Voltage
Measurement Method:
AC-coupled True RMS measurement.
Digital sampling with anti-alias filter.
Crest Factor:
No additional error for crest factors < 10.
Limited by peak input and 300 kHz bandwidth.
Peak Input:
300% of range or 1100 V
Overload Ranging:
Will select higher range if peak input
overload is detected during auto range.
Overload is reported in manual ranging.
AC CMR:
Triggering: Pre/Post, Int/Ext, Pos/Neg
Timebase Resolution: 19.9524 µs 0.01% accuracy
Maximum Input:
The peak value of the DC + AC current must
be < 300% of range. The RMS current must be
< 3 A including the DC current content.
DC CMRR:
Overall Bandwidth, DCV & DCI:
15 kHz typical @ 20 µs aperture (-3 dB)
Measurement Method:
Reciprocal-counting technique. AC-coupled input
using the AC voltage measurement function.
Input Impedance:
1 MΩ ± 2% in parallel with < 150 pF
Input Protection: 750 Vrms all ranges
Spurious-Free Dynamic Range
& Signal to Noise Distortion Ratio
Function DCV
Range
Spur-Free SNDR
1V
-75 dB
60 dB
1
10 V
-70 dB
60 dB
100 V
-75 dB
60 dB
1
10 V range: 2 V (p-p) < signal < 16 V (p-p)
Triggering and Memory
Reading Hold Sensitivity: 1% of reading
Samples per Trigger:
1 to 50,000
(34410A)
1 to 1,000,000 (34411A)
Trigger Delay: 0 to 3600 s (20 µs step size)
External Trigger:
Programmable edge, Low-power TTL compatible
Delay: < 1 µs Max rate: 5,000/s
Jitter: < 1 µs Min Pulsewidth: 1 µs
Capacitance
Measurement Method:
Current input with measurement of
resulting ramp.
Voltmeter Complete: 3 V Logic output,
2 µs pulse with programmable edge
Connection Type: 2-wire
Nonvolatile Memory: 50,000 readings
70 dB 2
Maximum Input: 400 Vdc, 1100 Vpk
Temperature
Input Impedance:
1 MΩ ± 2% in parallel with < 150 pF
Thermistor:
2.2 kΩ, 5 kΩ, and 10 kΩ
Input Protection: 750 Vrms all ranges
RTD: α = 0.00385
Ro from 49 Ω to 2.1 kΩ
Volatile Memory:
50,000 readings (34410A)
1,000,000 readings (34411A)
Sample Timer:
Range: 0 to 3600 s (20 µs step sizes)
Jitter:
< 100 ns
Resistance
Measurement Method:
Selectable 2-wire or 4-wire.
Current source referenced to LO input.
Offset Compensation:
Selectable on the 100 Ω, 1 kΩ,
and 10 kΩ ranges
Input Protection:
1000 V on all ranges
Function3
DCV
2-wire Ω
DCI
Frequency
Period
Filter setting
ACV
ACI
Input Protection:
1
2
Digits
4.5
50 k4
50 k4
50 k4
500
500
fast
500
500
5.5
10 k
10 k
10 k
90
90
med
150
150
3 A, 250 V fuse
For 1 kΩ unbalanced in LO lead and < 60 Hz, ± 500 V peak maximum
Maximum rate for DCV, DCI, and resistance functions
(using zero settling delay, autozero off, manual range)
4
34411A only
Power Consumption: 25 VA peak (16 W average)
Operating Environment: Full accuracy for
0 °C to 55 °C, 80% R.H. at 40 °C non-condensing
6.5
1k
1k
1k
10
10
slow
50
50
Storage Temperature: -40 °C to 70 °C
Weight: 3.72 kg (8.2 lbs)
Safety: IEC 61010-1, EN 61010-1, UL 61010-1,
CAN/CSA-C22.2 No. 61010-1, Refer to
Declarations of Conformity for current
revisions. Measurement CAT II 300 V,
CAT I 1000 V. Pollution Degree 2
EMC: IEC 61326, EN 61326, CISPR 11, ICES-001,
AS/NZS 2064.1, Refer to Declaration of
Conformity for current revisions.
Vibration & Shock: MIL-T-28800E,
Type III, Class 5 (Sine Only)
For 1 kΩ unbalanced in LO lead, ± 500 V peak maximum
3
Power Line Frequency:
45 Hz to 66 Hz and 360 Hz to 440 Hz,
Automatically sensed at power-on
Continuity Threshold: Fixed at 10 Ω
Operating Characteristics
Maximum readings/second
Current Shunt:
200 Ω for 100 µA, 1 mA
2 Ω for 10 mA, 100 mA
0.1 Ω for 1 A, 3 A
Power Supply:
100 V/120 V/220 V/240 V ± 10%
Response Time:
300 samples/sec with audible tone
Max. Lead Resistance (4-wire):
10% of range per lead for 100 Ω, 1 kΩ.
1 kΩ per lead on all other ranges
DC Current
General Specifications
Continuity/Diode Test
LXI Compliance: LXI Class C, ver. 1.0
5
Warranty: 1 year
Ordering Information
Agilent 34410A and 34411A Multimeters
Accessories included
Test lead kit with probes and
SMT attachments, calibration
certificate, power cord, and USB
interface cable.
Product Reference CD-ROM with
soft documentation and software:
• Programmer’s Reference Help
• Quick Start Tutorial
• User’s Guide
• Service Guide
• Programming Examples
• IntuiLink for Multimeters
• LabVIEW and IVI-COM drivers
Options
Opt. A6J ANSI Z540 compliant
calibration
Probes/Leads/Clip Accessories
11059A Kelvin probe set
11060A Surface mount device (SMD) test probes
11062A Kelvin clip set
34133A Precision electronic test leads
34134A DC coupled current probe
34136A High voltage probe
34138A Test lead set
34171B Input terminal connector
(sold in pairs)
34172B Input calibration short
(sold in pairs)
34308A Thermistor kit
34330A 30 A current shunt
E2308A 5 k thermistor probe
Y1133A Low-thermal external digital multimeter scanning kit
Rack Mount Kits
34190A Rackmount kit: designed for use with only one instrument, mounted
on either the left or the right side of the rack.
34191A 2U dual flange kit: secures the instrument to the front of the rack.
This kit can be used with the 34194A dual lock link kit to mount
two half-width, 2U height instruments side-by side.
34194A Dual lock link kit: recommended for side-by-side combinations and
includes links for instruments of different depths. This kit can be
used with the 34191A 2U dual flange kit to mount two half-width,
2U height instruments side-by-side.
Other Accessories
34131A Hard transit case
34162A Accessory pouch
E5810A LAN/GPIB gateway
6
www.agilent.com
www.agilent.com/find/DMM
myAgilent
www.agilent.com/find/myagilent
A personalized view into the information
most relevant to you.
www.axiestandard.org
AdvancedTCA® Extensions for Instrumentation and Test (AXIe) is
an open standard that extends the
AdvancedTCA for general purpose
and semiconductor test. Agilent
is a founding member of the AXIe
consortium.
www.lxistandard.org
LAN eXtensions for Instruments puts
the power of Ethernet and the Web
inside your test systems. Agilent
is a founding member of the LXI
consortium.
www.pxisa.org
PCI eXtensions for Instrumentation
(PXI) modular instrumentation
delivers a rugged, PC-based high-performance measurement and automation system.
Agilent Channel Partners
www.agilent.com/find/channelpartners
Get the best of both worlds: Agilent’s
measurement expertise and product
breadth, combined with channel
partner convenience.
For more information on Agilent
Technologies’ products, applications or
services, please contact your local Agilent
office. The complete list is available at:
www.agilent.com/find/ThreeYearWarranty
www.agilent.com/find/contactus
Agilent’s combination of product reliability
and three-year warranty coverage is another
Americas
way we help you achieve your business goals:
Canada
(877) 894 4414
increased confidence in uptime, reduced cost
Brazil
(11)
4197 3600
of ownership and greater convenience.
Three-Year Warranty
Agilent Advantage Services
www.agilent.com/find/AdvantageServices
Accurate measurements throughout the life of
your instruments.
www.agilent.com/quality
Mexico
United States
01800 5064 800
(800) 829 4444
Asia Pacific
Australia
China
Hong Kong
India
Japan
Korea
Malaysia
Singapore
Taiwan
Other AP Countries
1 800 629 485
800 810 0189
800 938 693
1 800 112 929
0120 (421) 345
080 769 0800
1 800 888 848
1 800 375 8100
0800 047 866
(65) 375 8100
Europe & Middle East
Belgium
32 (0) 2 404 93 40
Denmark
45 45 80 12 15
Finland
358 (0) 10 855 2100
France
0825 010 700*
*0.125 €/minute
49 (0) 7031 464 6333
Germany
Ireland
1890 924 204
Israel
972-3-9288-504/544
Italy
39 02 92 60 8484
Netherlands
31 (0) 20 547 2111
Spain
34 (91) 631 3300
Sweden
0200-88 22 55
United Kingdom 44 (0) 118 927 6201
For other unlisted countries:
www.agilent.com/find/contactus
(BP-3-1-13)
Product specifications and descriptions
in this document subject to change
without notice.
© Agilent Technologies, Inc. 2013
Published in USA, April 2, 2013
5989-3738EN
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement