HMC ALH482

HMC ALH482

Design Assistance

Customised Pack Sizes / Qtys

Assembly Assistance

Support for all industry recognised
supply formats:

Die handling consultancy

Hi-Rel die qualification

Hot & Cold die probing

Electrical test & trimming
o Waffle Pack
o Gel Pak
o Tape & Reel

Onsite storage, stockholding &
scheduling

100% Visual Inspection
o MIL-STD 883 Condition A
o MIL-STD 883 Condition A

On-site failure analysis

Bespoke 24 Hour monitored
storage systems for secure long
term product support

On-site failure analysis
Contact
[email protected]
For price, delivery and to place orders
HMC-ALH482
www.analog.com
www.micross.com
Analog Devices Welcomes
Hittite Microwave Corporation
NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED
www.analog.com
www.hittite.com
THIS PAGE INTENTIONALLY LEFT BLANK
HMC-ALH482
v04.1009
LOW NOISE AMPLIFIERS - CHIP
1
GaAs HEMT MMIC LOW NOISE
AMPLIFIER, 2 - 22 GHz
Typical Applications
Features
This HMC-ALH482 is ideal for:
Noise Figure: 1.7 dB @ 2-12 GHz
• Wideband Communication Systems
Noise Figure: 2.2 dB @ 12-22 GHz
• Surveillance Systems
Gain: 16 dB @ 12 GHz
• Point-to-Point Radios
P1dB Output Power: +14 dBm
• Point-to-Multi-Point Radios
Supply Voltage: +4V @ 45 mA
• Military & Space
Die Size: 2.04 x 1.2 x 0.1 mm
• Test Instrumentation
General Description
Functional Diagram
The HMC-ALH482 is a GaAs MMIC HEMT Low Noise
Wideband Amplifier die which operates between 2
and 22 GHz. The amplifier provides 16 dB of gain, 1.7
dB noise figure up to 12 GHz and +14 dBm of output
power at 1 dB gain compression while requiring only
45 mA from a +4V supply voltage. The HMC-ALH482
amplifier is ideal for integration into Multi-ChipModules (MCMs) due to its small size.
Electrical Specifi cations*, TA = +25° C, Vdd= +4V
Parameter
Min.
Frequency Range
Gain
Typ.
Max.
Min.
2 - 12
15
Gain Variation over Temperature
Noise Figure
16
15
0.01
1.7
Typ.
Max.
12 - 22
2.5
GHz
16
dB
0.01
dB / °C
2.2
3
dB
Input Return Loss
8
6
Output Return Loss
10
5
dB
Output Power for 1 dB Compression
14
14
dBm
Supply Current (Idd) (Vdd = 4V, Vgg = -0.2V Typ.)
45
45
mA
*Unless otherwise indicated, all measurements are from probed die
1 - 204
Units
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
dB
HMC-ALH482
v04.1009
GaAs HEMT MMIC LOW NOISE
AMPLIFIER, 2 - 22 GHz
3
20
18
2.5
NOISE FIGURE (dB)
16
GAIN (dB)
14
12
10
8
6
4
2
1.5
1
0.5
2
0
0
0
2
4
6
8
10
12
14
16
18
20
22
0
24
2
4
6
FREQUENCY (GHz)
8
10
12
14
16
18
20
22
24
22
24
FREQUENCY (GHz)
Input Return Loss vs. Frequency
Output Return Loss vs. Frequency
0
0
-4
RETURN LOSS (dB)
RETURN LOSS (dB)
-2
-6
-8
-10
-12
-5
-10
-15
LOW NOISE AMPLIFIERS - CHIP
1
Noise Figure vs. Frequency
Linear Gain vs. Frequency
-20
-14
-16
-25
0
2
4
6
8
10
12
14
16
FREQUENCY (GHz)
18
20
22
24
0
2
4
6
8
10
12
14
16
18
20
FREQUENCY (GHz)
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
1 - 205
HMC-ALH482
v04.1009
GaAs HEMT MMIC LOW NOISE
AMPLIFIER, 2 - 22 GHz
LOW NOISE AMPLIFIERS - CHIP
1
Absolute Maximum Ratings
Drain Bias Voltage
+5 Vdc
Drain Bias Current
60 mA
RF Input Power
5 dBm
Gate Bias Voltage
-1 to 0.3 Vdc
Channel Temperature
180 °C
Continuous Pdiss (T = 85 °C)
derate 4.7 mW/ °C above 85 °C
0.45 W
Thermal Resistance
(channel to die bottom)
213.3 °C/W
Storage Temperature
-65 to +150 °C
Operating Temperature
-55 to +85 °C
Outline Drawing
Die Packaging Information [1]
Standard
Alternate
GP-2 (Gel Pack)
[2]
[1] Refer to the “Packaging Information” section for die
packaging dimensions.
[2] For alternate packaging information contact Hittite
Microwave Corporation.
1 - 206
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
NOTES:
1. ALL DIMENSIONS ARE IN INCHES [MM].
2. TYPICAL BOND PAD IS .004” SQUARE.
3. BACKSIDE METALLIZATION: GOLD.
4. BACKSIDE METAL IS GROUND.
5. BOND PAD METALLIZATION: GOLD.
6. CONNECTION NOT REQUIRED FOR UNLABELED BOND PADS.
7. OVERALL DIE SIZE ±.002”
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC-ALH482
v04.1009
GaAs HEMT MMIC LOW NOISE
AMPLIFIER, 2 - 22 GHz
Pad Number
Function
Description
1
RFIN
This pad is AC coupled
and matched to 50 Ohms.
2
RFOUT
This pad is AC coupled
and matched to 50 Ohms.
3
Vdd
Power Supply Voltage for the amplifier. See assembly for
required external components.
4
Vgg
Gate control for amplifier. Please follow “MMIC Amplifier Biasing Procedure” application note. See assembly for required
external components.
Die bottom
GND
Die bottom must be connected to RF/DC ground.
Interface Schematic
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
LOW NOISE AMPLIFIERS - CHIP
1
Pad Descriptions
1 - 207
HMC-ALH482
v04.1009
GaAs HEMT MMIC LOW NOISE
AMPLIFIER, 2 - 22 GHz
Assembly Diagram
LOW NOISE AMPLIFIERS - CHIP
1
Note 1: Bypass caps should be 100 pF (approximately) ceramic (single-layer) placed no farther than 30 mils from the amplifier.
Note 2: Best performance obtained from use of <10 mil (long) by 3 by 0.5mil ribbons on input and output.
1 - 208
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC-ALH482
v04.1009
GaAs HEMT MMIC LOW NOISE
AMPLIFIER, 2 - 22 GHz
The die should be attached directly to the ground plane eutectically or with
conductive epoxy (see HMC general Handling, Mounting, Bonding Note).
50 Ohm Microstrip transmission lines on 0.127mm (5 mil) thick alumina
thin film substrates are recommended for bringing RF to and from the chip
(Figure 1). If 0.254mm (10 mil) thick alumina thin film substrates must be
used, the die should be raised 0.150mm (6 mils) so that the surface of
the die is coplanar with the surface of the substrate. One way to accomplish this is to attach the 0.102mm (4 mil) thick die to a 0.150mm (6 mil)
thick molybdenum heat spreader (moly-tab) which is then attached to the
ground plane (Figure 2).
0.102mm (0.004”) Thick GaAs MMIC
Wire Bond
0.076mm
(0.003”)
RF Ground Plane
Microstrip substrates should be placed as close to the die as possible in
order to minimize bond wire length. Typical die-to-substrate spacing is
0.076mm to 0.152 mm (3 to 6 mils).
0.127mm (0.005”) Thick Alumina
Thin Film Substrate
Figure 1.
Handling Precautions
Follow these precautions to avoid permanent damage.
Storage: All bare die are placed in either Waffle or Gel based ESD protective containers, and then sealed in an ESD protective bag for shipment.
Once the sealed ESD protective bag has been opened, all die should be
stored in a dry nitrogen environment.
Cleanliness: Handle the chips in a clean environment. DO NOT attempt
to clean the chip using liquid cleaning systems.
Static Sensitivity:
strikes.
0.102mm (0.004”) Thick GaAs MMIC
Wire Bond
0.076mm
(0.003”)
RF Ground Plane
Follow ESD precautions to protect against ESD
Transients: Suppress instrument and bias supply transients while bias
is applied. Use shielded signal and bias cables to minimize inductive
pick-up.
LOW NOISE AMPLIFIERS - CHIP
1
Mounting & Bonding Techniques for Millimeterwave GaAs MMICs
0.150mm (0.005”) Thick
Moly Tab
0.254mm (0.010”) Thick Alumina
Thin Film Substrate
Figure 2.
General Handling: Handle the chip along the edges with a vacuum collet or with a sharp pair of bent tweezers. The
surface of the chip has fragile air bridges and should not be touched with vacuum collet, tweezers, or fingers.
Mounting
The chip is back-metallized and can be die mounted with AuSn eutectic preforms or with electrically conductive epoxy.
The mounting surface should be clean and flat.
Eutectic Die Attach: A 80/20 gold tin preform is recommended with a work surface temperature of 255 °C and a tool
temperature of 265 °C. When hot 90/10 nitrogen/hydrogen gas is applied, tool tip temperature should be 290 °C. DO
NOT expose the chip to a temperature greater than 320 °C for more than 20 seconds. No more than 3 seconds of
scrubbing should be required for attachment.
Epoxy Die Attach: Apply a minimum amount of epoxy to the mounting surface so that a thin epoxy fillet is observed
around the perimeter of the chip once it is placed into position. Cure epoxy per the manufacturer’s schedule.
Wire Bonding
RF bonds made with 0.003” x 0.0005” ribbon are recommended. These bonds should be thermosonically bonded
with a force of 40-60 grams. DC bonds of 0.001” (0.025 mm) diameter, thermosonically bonded, are recommended.
Ball bonds should be made with a force of 40-50 grams and wedge bonds at 18-22 grams. All bonds should be made
with a nominal stage temperature of 150 °C. A minimum amount of ultrasonic energy should be applied to achieve
reliable bonds. All bonds should be as short as possible, less than 12 mils (0.31 mm).
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
1 - 209
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement