Wood Stone WS-MS-7-W Specifications

Wood Stone WS-MS-7-W Specifications
Installation and
Operation Manual
MT. CHUCKANUT
MOUNTAIN SERIES
Stone Hearth Oven
Dual Burner, Gas-Fired Models
WS-MS-4-RFG-IR, RFG-IR
MT. ADAMS
WS-MS-5-RFG-IR, RFG-IR
MT. BAKER
WS-MS-6-RFG-IR, RFG-IR-(NAP)
MT. RAINIER
WS-MS-7-RFG-IR, RFG-IR
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
woodstone-corp.com
Revised May 2015
Part no: 9500-0202
Doc no: M0033.03
TABLE OF CONTENTS
Mountain Series
Installation and Operation Manual
TABLE OF CONTENTS
MOUNTAIN SERIES���������������������������������������������������������� 3
CAUTIONS AND WARNINGS���������������������������������������������� 4
UNLOADING AND MOVING������������������������������������������������ 6
INSTALLATION CLEARANCES�������������������������������������������� 7
FACADE DETAILS������������������������������������������������������������ 9
OUTDOOR INSTALLATION ���������������������������������������������� 10
GAS SPECIFICATIONS���������������������������������������������������� 11
ELECTRICAL SPECIFICATIONS ���������������������������������������� 13
OVEN VENTING ������������������������������������������������������������ 14
FLUE ADAPTER ������������������������������������������������������������ 17
VENTING DO’S AND DON’TS ������������������������������������������ 18
ASSEMBLY ������������������������������������������������������������������ 26
MANTLE MOUNTING������������������������������������������������������ 27
FRONT PANEL ASSEMBLY���������������������������������������������� 28
EXTENSION PANEL ASSEMBLY���������������������������������������� 29
STUCCO APPLICATION �������������������������������������������������� 31
CONTROLLER �������������������������������������������������������������� 32
INITIAL START-UP �������������������������������������������������������� 33
DAILY OPERATION �������������������������������������������������������� 34
FLAME HEIGHT CONTROL���������������������������������������������� 35
MAINTENANCE ������������������������������������������������������������ 36
PERIODIC THERMAL CLEANING �������������������������������������� 37
TROUBLESHOOTING GUIDE�������������������������������������������� 38
OPERATION SEQUENCE�������������������������������������������������� 39
120 VAC ELECTRICAL DIAGRAM�������������������������������������� 40
240 VAC ELECTRICAL DIAGRAM�������������������������������������� 41
INTERLOCK DIAGRAM���������������������������������������������������� 42
LIMITED WARRANTY������������������������������������������������������ 43
An ongoing program of product improvement may require us to change
specifications without notice. WS-MS-(4, 5, 6, 7)-RFG-IR,
Revised May 2015.
Doc no: M0033.03
2
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
MOUNTAIN SERIES
Mountain Series
Installation and Operation Manual
INSTALLATION AND OPERATION MANUAL
THE WOOD STONE MOUNTAIN SERIES
STONE HEARTH COOKING EQUIPMENT
WS-MS-(4, 5, 6, 7)-RFG-IR MODELS (INCLUDES MS-6 NAPLES MODEL)
GAS-FIRED OVEN
ADDITIONAL COPIES AVAILABLE UPON REQUEST
An ongoing program of product improvement may require us to change
specifications without notice. WS-MS-(4, 5, 6, 7)-RFG-IR,
Revised May 2015.
Doc no: M0033.03
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
3
CAUTIONS AND WARNINGS
Mountain Series
Installation and Operation Manual
WOOD STONE MOUNTAIN SERIES
GAS-FIRED OVEN OPERATING INSTRUCTIONS
RETAIN THIS MANUAL FOR FUTURE REFERENCE
Additional copies of this manual at woodstone-corp.com.
For prompt responses to service/maintenance questions, call us at @ 1-800-988-8103.
FOR YOUR SAFETY: Consult your local gas supplier for a statement outlining a procedure to be followed
in the event you smell gas. Post the statement in a prominent location.
READ ALL INSTRUCTIONS BEFORE INSTALLING AND USING THIS APPLIANCE
Please read this entire manual before you install the oven. Failure to follow instructions may result in
property damage, bodily injury or even death. Contact your local building or fire officials about restrictions
and installation inspection in your area.
WHEN THE OVEN IS NOT PROPERLY INSTALLED, A FIRE MAY RESULT.
TO REDUCE RISK OF FIRE, FOLLOW THE INSTALLATION INSTRUCTION.
FOR YOUR SAFETY: Do not store or use gasoline or other flammable vapors or liquids in the vicinity of
this or any other appliance. Also, always keep the area under and around this appliance free and clear of
any and all combustible materials.
IN THE EVENT OF A POWER FAILURE, NO ATTEMPT SHOULD BE MADE TO OPERATE THE OVEN.
IMPORTANT: It is recommended that this oven be installed, maintained and serviced by authorized
professionals.
An ongoing program of product improvement may require us to change
specifications without notice. WS-MS-(4, 5, 6, 7)-RFG-IR,
Revised May 2015.
Doc no: M0033.03
4
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
CAUTIONS AND WARNINGS
Mountain Series
Installation and Operation Manual
A MAJOR CAUSE OF OVEN RELATED FIRES IS A
FAILURE TO MAINTAIN REQUIRED CLEARANCES
TO COMBUSTIBLE MATERIAL. IT IS OF UTMOST
IMPORTANCE THAT THIS OVEN BE INSTALLED ONLY
IN ACCORDANCE WITH THESE INSTRUCTIONS.
CAUTION: DISCONNECT POWER TO THE OVEN BEFORE SERVICING OR CLEANING.
WARNING: Improper installation, adjustment, alteration, service or maintenance can cause property
damage, injury or death. Read the installation, operating and maintenance instructions thoroughly before
installing or servicing this equipment.
WARNING: This product must be installed by a licensed plumber or gas fitter when installed within the
Commonwealth of Massachusetts.
SAVE THE INSTRUCTIONS
Wood Stone’s gas-fired ovens have been tested and approved by Intertek Testing Services,
and are ETL Listed to ANSI Z83.11b - 2009, CSA 1.8b-2009
and to NSF/ANSI Standard 4 - 2009.
An ongoing program of product improvement may require us to change
specifications without notice. WS-MS-(4, 5, 6, 7)-RFG-IR,
Revised May 2015.
Doc no: M0033.03
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
5
UNLOADING AND MOVING
Mountain Series
Installation and Operation Manual
LIFTING THE OVEN
1. USING A CRANE
The oven arrives with four lifting eyes attached. When craning a Wood
Stone oven, use a spreader bar with a two-legged sling rigged on each
end. The spreader bar should be of a sufficient length to keep the sling
from contacting the oven.
NOTE: Once lifting eyes are no longer needed, remove the lifting eyes
one at a time AND BE SURE TO REPLACE THE BOLTS THAT ATTACH
THE OVEN TO THE STAND.
2. USING A FORKLIFT
Be sure to use a forklift rated, and forks the minimum length, as shown
in the table below. If necessary, fork extensions must be used so the
forks extend through the fork lift pockets to the opposite side of the
stand. Lift from either side as shown. Do not lift from the front or back.
The oven is very top heavy, so spread the forks as far apart as possible.
Model
WS-MS-4
WS-MS-5
WS-MS-6
WS-MS-7
Oven
Mt. Chuckanut
Mt. Adams
Mt. Baker
Mt. Rainier
Approximate
shipping
weight
2,400 lbs.
3,600 lbs.
4,600 lbs.
6,000 lbs.
Minimum
fork length
required
4'
5'
6'
7'
Required
forklift
capacity
5,000 lbs.
6,000 lbs.
6,000 lbs.
9,000 lbs.
3. USING A PALLET JACK
Once the oven has been removed from the delivery vehicle, it can easily
be moved on flat surfaces using a pallet jack. To lift the oven with a pallet
jack, remove the front and rear angle iron stabilizers from the base of the
oven stand and place a stout 4x4 post through the fork pocket as shown.
THE OVEN IS VERY TOP-HEAVY. MOVING THE OVEN UP OR DOWN A
RAMP OR INCLINE ON A PALLET JACK IS NOT SAFE!
4x4 post
DO NOT TURN THE OVEN ON ITS SIDE!
Contact Wood Stone if the oven must be turned on its side for specific instructions. Moving a Wood Stone oven can
present challenges to even the most experienced riggers. Take your time, use your head, secure the proper equipment
and make safety your first priority. Please don’t hesitate to call the factory for technical support.
DELIVERY NOTE: The customer will receive an Oven Shipping Notification when the oven leaves the Wood Stone
factory. This will include a PRO# and a trucking company contact number. Wood Stone recommends that you confirm the
delivery date/time with the trucking company before committing to heavy equipment and/or labor. Our goal is a smooth
and safe delivery.
An ongoing program of product improvement may require us to change
specifications without notice. WS-MS-(4, 5, 6, 7)-RFG-IR,
Revised May 2015.
Doc no: M0033.03
6
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
INSTALLATION CLEARANCES
Mountain Series
Installation and Operation Manual
CLEARANCES
1. The Wood Stone gas-fired oven must have a minimum 1" clearance to combustibles from all sides, and 14"
clearance to combustibles from the top (see INSTALLATION CLEARANCES section on next page). If building a
facade that will contact the oven, use completely non-combustible materials*. Please note that standard Drywall (or
Sheetrock) is considered a combustible.
2. Any facade materials 6" to either side of the oven doorway and above must be constructed of non-combustible
building materials.
3. Install this oven only on a non-combustible floor surface. (Cet appareil doit être installé sur une surface de plancher
non-combustible.) The non-combustible floor surface should extend 36" out in front of the oven, and extend 30" to
either side of the oven doorway.
*When non-combustible building materials contact the body of the appliance, the clearances to combustibles are
transferred to those non-combustibles.
NOTICE: For stucco-ready appliances (model numbers ending in “-S”), the same clearances as described above apply.
Non-combustible stucco mix must be used and applied to a minimum thickness of 1".
IF THIS OVEN IS NOT PROPERLY INSTALLED A FIRE MAY RESULT. TO REDUCE THE RISK OF FIRE, FOLLOW THESE
INSTALLATION INSTRUCTIONS. A MAJOR CAUSE OF OVEN RELATED FIRES IS FAILURE TO MAINTAIN REQUIRED
CLEARANCES (AIR SPACES) TO COMBUSTIBLE MATERIALS. IT IS OF UTMOST IMPORTANCE THAT THIS OVEN BE
INSTALLED ONLY IN ACCORDANCE WITH THESE INSTRUCTIONS.
WARNING: DO NOT PACK REQUIRED AIR SPACES WITH INSULATION OR OTHER MATERIAL.
!
WARNING: Installation and servicing of this product could expose you to glasswool/ceramic
fibers as well as calcium silicate dust. ALWAYS WEAR RESPIRATORY AND EYE PROTECTION
WHEN INSTALLING OR SERVICING THIS APPLIANCE. Please read this entire manual before
you install the oven. Failure to follow instructions may result in property damage, bodily
injury or even death. Contact your local building or fire officials about restrictions and
installation inspection in your area.
PLEASE READ THIS ENTIRE MANUAL BEFORE YOU INSTALL THE OVEN. FAILURE TO FOLLOW INSTRUCTIONS
MAY RESULT IN PROPERTY DAMAGE, BODILY INJURY OR EVEN DEATH. CONTACT YOUR LOCAL BUILDING OR
FIRE OFFICIALS ABOUT RESTRICTIONS AND INSTALLATION INSPECTION IN YOUR AREA.
An ongoing program of product improvement may require us to change
specifications without notice. WS-MS-(4, 5, 6, 7)-RFG-IR,
Revised May 2015.
Doc no: M0033.03
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
7
INSTALLATION CLEARANCES
Mountain Series
Installation and Operation Manual
THE FOLLOWING CLEARANCE INFORMATION APPLIES TO ALL
WOOD STONE MOUNTAIN SERIES OVENS
14" top clearance to combustible
building materials.
14"
Any facade materials 6" to either side of
the doorway and above must be NONCOMBUSTIBLE.
1" side clearance to combustible
building materials.
Note: 0" side and top clearance to noncombustible materials. However, the
respective clearances to combustibles
are transferred to those noncombustibles.
For use only on noncombustible floors
(installér sur un plancher incombustible
seulement). Non-combustible floor
surface AND provided with a noncombustible floor covering at least 30"
to each side of, and 36" in front of the
door opening.
Combustible building material
Non-combustible building material
Any facade wall 6" to either side of the
oven doorway and above MUST be of
non-combustible construction with no
exceptions.
An ongoing program of product improvement may require us to change
specifications without notice. WS-MS-(4, 5, 6, 7)-RFG-IR,
Revised May 2015.
Doc no: M0033.03
8
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
FACADE DETAILS
Mountain Series
Installation and Operation Manual
Wood Stone Mountain Series (MS-) ovens carry an ETL Sanitation listing. The oven interior only is ETL listed to NSF/
ANSI Standard 4. This means that the surfaces of the oven which are meant to be left exposed after the facade has
been put in place have been evaluated from the standpoint of sanitation and food safety and found to comply with NSF/
ANSI Standard 4. To operate the oven in accordance with NSF/ANSI Standard 4, only pizza and bread products may be
cooked directly on the floor of the oven. Other types of food may be cooked on or in pans, or other suitable containers to
prevent spillage onto the oven deck.
Go to www.woodstone-corp.com for detailed instructions for constructing a facade around a Wood Stone oven.
If using an exhaust hood over the oven, make sure
your facade allows proper access for removal of the
hood filters.
A removable Service Panel or storage box allows
access for service of gas and electrical components.
If this panel is not used, access and air intake of
equivalent dimensions MUST be provided at the
front of the oven.
Hatched areas shall not be exposed after installation of facade.
Any facade wall 6" to either side of the oven doorway and
above MUST be of non-combustible construction with no
exceptions.
An ongoing program of product improvement may require us to change
specifications without notice. WS-MS-(4, 5, 6, 7)-RFG-IR,
Revised May 2015.
Doc no: M0033.03
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
9
OUTDOOR INSTALLATION
Mountain Series
Installation and Operation Manual
OUTDOOR INSTALLATIONS
The Mountain Series (MS-) model ovens are ETL approved for outdoor installation. When installed outdoors, the open
area beneath the oven must be enclosed, with the exception of the perforated area on the front Service Panel (or storage
box) for air intake. The oven may be installed in a weatherproof enclosure. If so be sure to maintain all clearances and
adhere to the installation requirements included in this manual.
KEEP THE AREA AROUND AND BENEATH THE OVEN CLEAR OF GRASS, LEAVES
AND OTHER COMBUSTIBLE MATERIALS.
Wood Stone also offers the following options to enclose the area beneath the oven
Lower Lagging Kit
Stand Wrap Kit
An ongoing program of product improvement may require us to change
specifications without notice. WS-MS-(4, 5, 6, 7)-RFG-IR,
Revised May 2015.
Doc no: M0033.03
10
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
GAS SPECIFICATIONS
Mountain Series
Installation and Operation Manual
The Wood Stone Gas ovens are equipped with a 3/4" NPT gas connection located at the rear left of the oven. Have a
licensed gas installer provide the hook-up and test all fittings and pipe connections for leaks. Use approved gas leak
detectors (soap solutions or equivalent) over and around the fittings and pipe connections. DO NOT USE FLAME TO
TEST FOR LEAKS!
SV-1 is the gas control valve that operates the Underfloor Infrared (IR) burner. The manifold pressure test port is 1/8: NPT
pugged tap located on the IR burner manifold.
SV-2 is the gas control valve that operates the interior radiant burner. SV-2 is located at the rear left beneath the oven.
The manifold pressure test port for the radiant burner is a 1/8" NPT plugged tap located at the base of the T-junction
between the SV-2 and the radiant/interior burner.
NOTE: Gas valves are shipped in the ON position.
The burner manifold pressure has been adjusted and tested at the factory. A variety of factors can influence this pressure,
so be sure to test the burner manifold pressure and adjust the valve as necessary to achieve the specified pressure.
NOTE: Maximum inlet gas pressure: 1/2 psi (14 inches W.C.)
This oven requires no modifications or adjustments for use at high altitudes.
Factory specified individual burner manifold pressures (W.C.) for RFG-IR models equipped to burn
Natural Gas (NG)
Model
WS-MS-4-RFG-IR-NG
WS-MS-5-RFG-IR-NG
WS-MS-6-RFG-IR-NG
WS-MS-7-RFG-IR-NG
SV-1
SV-2
3.5"
3.5"
3.5"
3.5"
5"
4.75"
4.75"
4.6"
Factory specified individual burner manifold pressures (W.C.) for RFG-IR models equipped to burn
Propane (LP & HLP)
Model
WS-MS-4-RFG-IR-LP
WS-MS-5-RFG-IR-LP
WS-MS-6-RFG-IR-LP
WS-MS-7-RFG-IR-LP
SV-1
SV-2
9"
9"
9"
9.2"
7"
8"
8"
9.5"
An ongoing program of product improvement may require us to change
specifications without notice. WS-MS-(4, 5, 6, 7)-RFG-IR,
Revised May 2015.
Doc no: M0033.03
Model
WS-MS-4-RFG-IR-HLP
WS-MS-5-RFG-IR-HLP
WS-MS-6-RFG-IR-HLP
WS-MS-7-RFG-IR-HLP
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
SV-1
SV-2
9"
9"
9"
9.2"
7"
8"
8"
9.5"
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
11
GAS SPECIFICATIONS
Mountain Series
Installation and Operation Manual
Hourly Natural Gas (NG) BTU/hr input rates for Wood Stone RFG-IR models
Model
WS-MS-4-RFG-IR-NG
WS-MS-5-RFG-IR-NG
WS-MS-6-RFG-IR-NG
WS-MS-6-RFG-IR-NAP-NG
WS-MS-7-RFG-IR-NG
BTU/hr Input Rate
125,000
188,000
188,000
218,330
220,000
Note: For MS-4, 5, 7-RFG-IR-NAP-NG models there is no change in BTU/hr.
Hourly Propane (LP & HLP) BTU/hr input rates for Wood Stone RFG-IR models
Model
WS-MS-4-RFG-IR-LP
WS-MS-5-RFG-IR-LP
WS-MS-6-RFG-IR-LP
WS-MS-6-RFG-IR-NAP-LP
WS-MS-7-RFG-IR-LP
BTU/hr Input Rate
110,000
159,000
159,000
218,330
227,000
Model
WS-MS-4-RFG-IR-HLP
BTU/hr Input Rate
WS-MS-5-RFG-IR-HLP
WS-MS-6-RFG-IR-HLP
WS-MS-6-RFG-IR-NAP-HLP
WS-MS-7-RFG-IR-HLP
125,000
188,000
188,000
218,330
227,000
Note: For MS-4, 5, 7-RFG-IR-NAP-LP models there is no change in BTU/hr.
Wood Stone recommends that the appliance’s individual shutoff valve (supplied by others) be left readily
accessible. Wood Stone also recommends that inspection and maintenance of the burners and gas piping
connections of this appliance be performed at regularly scheduled intervals and only by professional gas
appliance service agencies.
GAS CODE LIMITATIONS
The installation of this appliance must conform with local codes, or in the absence of local codes, with the National Fuel
Gas Code, ANSI Z223.1 or The Natural Gas installation Code CAN/CGA-B149.1 as applicable, including:
The appliance and its individual shutoff valve (supplied by others) must be disconnected from the gas supply piping
system during any pressure testing of that system at test pressures in excess of 1/2 psi (3.45 kPa).
The appliance must be isolated from the gas supply piping system by closing its individual manual shutoff valve (supplied
by others) during any pressure testing of the gas supply piping system at test pressure, equal to or less than 1/2 psi
(3.45 kPa).
An ongoing program of product improvement may require us to change
specifications without notice. WS-MS-(4, 5, 6, 7)-RFG-IR,
Revised May 2015.
Doc no: M0033.03
12
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
ELECTRICAL SPECIFICATIONS
Mountain Series
Installation and Operation Manual
Incoming power should be connected to the terminal strip located in the Transformer Junction Box beneath the oven
(see diagram below). The standard oven model comes configured for connection to a 120 VAC circuit. The oven can
be ordered configured for connection to a 240 VAC circuit. Always refer to the equipment data plate beneath the oven
to verify the proper voltage. The voltage is also specified on the transformer box cover. Never connect an oven rated
120 VAC to a 240 VAC circuit or vice versa. It is recommended that the oven be connected to its own individual branch
circuit. Have a licensed electrician connect the oven to the appropriate 120 VAC or 240 VAC circuit. Electrical diagrams
are located directly to the right, behind the removable service/intake panel of the appliance as well as inside the control
box. Electrical diagrams are also located near the end of this manual. See the FRONT PANEL ASSEMBLY section of this
manual for the location of the transformer housing.
ELECTRICAL RATINGS
120 VAC, 1.1A, 50/60 Hz
240 VAC, 1.1A, 50/60 Hz
ELECTRICAL CODE LIMITATIONS
Electrical Grounding: This appliance must be electrically grounded in accordance with local codes, or in the absence of
local codes, with the National Electrical code, ANSI/NFPA 70 or the Canadian Electrical Code, CSA C22.1 as applicable.
Terminal Strip location
An ongoing program of product improvement may require us to change
specifications without notice. WS-MS-(4, 5, 6, 7)-RFG-IR,
Revised May 2015.
Doc no: M0033.03
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
13
VENTING
Mountain Series
Installation and Operation Manual
The following are the manufacturer’s recommendations for venting the Wood Stone MS (Mountain Series) RFG-IR ovens.
It is never appropriate to use “B vent” in any part of an exhaust system connected to a Wood Stone oven. All duct material
must be manufactured to the specifications of a grease duct. Submit your venting plans to your local authorities before
proceeding with your installation, as there may be additional requirements in your area. All non-solid fuel venting systems
should be inspected and cleaned at least every 3 months.
There are three venting options.
VENTING OPTION 1
Direct Connection: A Listed building heating appliance chimney, also listed as a grease duct as described in NFPA 96,
connected directly to the oven flue collar and provided with a power ventilator listed for restaurant appliance exhaust.
The power ventilator should be rated for a minimum of 300 °F. Wood Stone does not recommend the use of an in-line
fan. A field built grease duct, constructed and installed to the specifications of a grease duct as detailed in NFPA 96 or
the International Mechanical Code, may also be used.
A static pressure of -0.1 inches water column is necessary at the oven flue collar to ensure that flue gas temperatures
do not exceed 300 °F at the fan inlet. This measurement may be taken by inserting the probe of the magnahelic gauge
through the oven doorway, upwards to the oven flue collar. NOTE: Double door ovens (models ending in “-DD”), have two
flue collars. Both must be connected and a static pressure of negative 0.1 inches must be maintained at each collar. See
table below for CFM required to attain the specified static pressure.
CFM REQUIREMENTS
Model
CFM required
WS-MS-4-RFG-IR
WS-MS-5-RFG-IR
WS-MS-6-RFG-IR
WS-MS-7-RFG-IR
400
450
450
450
Install the venting system in accordance with the duct
manufacturer’s instructions and in accordance with all local codes.
All field built components should be built to the applicable codes
and standards and are subject to the approval of the authority
having jurisdiction.
NOTE: If your MS-5, MS-6 or MS-7 oven is ordered from Wood Stone without a hood, it will have a round flue adapter
installed to facilitate direct connection to a round duct. If the oven is to be installed under a hood, it MAY be necessary
to remove the round adapter to properly position the hood. This is done by removing the screws that attach the adapter
to the oven. Please contact Wood Stone if you have any questions.
Collar I.D.
Model
WS-MS-5
WS-MS-6
WS-MS-7
Flue adapter
An ongoing program of product improvement may require us to change
specifications without notice. WS-MS-(4, 5, 6, 7)-RFG-IR,
Revised May 2015.
Doc no: M0033.03
14
Oven
Flue Collar I.D. (nominal)
Mt. Adams
Mt. Baker
Mt. Rainier
10 inch
10 inch
10 inch
NOTE: MS-4 ovens come standard with a round 8" O.D. collar
and do not require the flue adapter for a direct connection.
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
OVEN VENTING
Mountain Series
Installation and Operation Manual
INSTALLATION VIEWS OF A WOOD STONE HOOD
Flat face hood
Curved face hood
Allow sufficient
opening between
any facade and the
inside edge of the
front of the hood to
allow for filter removal
and hood cleaning.
Any front facade wall
should not be built
any higher than the
top of the oven to
allow for access to
the filter.
VENTING OPTION 2
A Listed Type 1 exhaust hood or one that is constructed and installed in accordance with all relevant Local and National
Codes. Wood Stone offers eyebrow-type hoods designed specifically for Wood Stone ovens. See specification sheet on
ventilators for Wood Stone ovens. Note that the notch of the hood is even with the front edge of the oven. The hood must
be installed in accordance with the hood manufacturer’s instructions, and with the Standard for Ventilation Control and
Fire Protection of Commercial Cooking Operations, NFPA 96 and/or the applicable local and national codes. Refer to the
exhaust hood manufacturer’s recommendations for inspection, maintenance and cleaning.
VENTING OPTION 3
Exhaust from Wood Stone gas-fired ovens (RFG-IR models) can be vented using one of the previously mentioned
methods OR, when vented with a hood, can be combined with exhaust from other equipment, assuming the common
duct meets the construction requirements listed in Option 1. The system must be properly engineered to provide proper
airflow to hood serving the oven.
It is never appropriate to use “B vent” in any part of an exhaust system connected to a Wood Stone oven. All
duct material must be manufactured to the specifications of a grease duct. Due to the possibility of sparks entering the
duct, exhaust systems serving solid fuel equipment MUST NOT be combined with exhaust systems serving other (nonsolid fuel) equipment.
VERY IMPORTANT!
WOOD STONE RECOMMENDS THAT YOU CONSULT WITH A QUALIFIED MECHANICAL ENGINEER
AND SUBMIT YOUR VENTING PLANS TO LOCAL CODE AUTHORITIES
BEFORE PROCEEDING WITH INSTALLATION.
An ongoing program of product improvement may require us to change
specifications without notice. WS-MS-(4, 5, 6, 7)-RFG-IR,
Revised May 2015.
Doc no: M0033.03
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
15
OVEN VENTING
Mountain Series
Installation and Operation Manual
FIRE SUPPRESSION
Check with your local code officials to see if fire suppression is required in your area. If fire suppression is required, you
must vent the oven using a Type 1 hood constructed and installed in accordance with NFPA 96. If fire suppression is
required, Wood Stone recommends providing protection for the hood duct collar and plenum. The fusible link in the hood
must be rated at 450 °F minimum. Wood Stone offers Listed exhaust hoods for our ovens that are pre-piped for ANSUL
R-102 fire suppression. Wood Stone does not recommend aiming any fire suppression nozzles into the cooking chamber
of the oven. All installations are subject to the approval of the local authority having jurisdiction.
An ongoing program of product improvement may require us to change
specifications without notice. WS-MS-(4, 5, 6, 7)-RFG-IR,
Revised May 2015.
Doc no: M0033.03
16
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
FLUE ADAPTER
Mountain Series
Installation and Operation Manual
MOUNTAIN SERIES OVENS: FLUE ADAPTER
The flue adapter unit is designed to facilitate connection to a round duct. Use the stainless steel screws and sealant
provided to attach the flue adapter to the exhaust outlet on the oven if it is not already installed. NOTE: MS-4 ovens come
standard with a round 8" O.D. collar and do not require the flue adapter for a direct connection.
Note: If using a Selkirk or other modular-type duct, attach according to the manufacturer’s instructions. Otherwise, the
duct must be attached with a full perimeter weld. All duct must be grease-rated duct. If the oven is going to be enclosed,
the flue adapter and exhaust outlet must be wrapped with an insulating material approved for use with a grease-duct.
Flue adapter
Flue adapter attached
to oven flue collar
If the oven is to
be enclosed, wrap
with an approved
insulation.
An ongoing program of product improvement may require us to change
specifications without notice. WS-MS-(4, 5, 6, 7)-RFG-IR,
Revised May 2015.
Doc no: M0033.03
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
17
VENTING DO’S AND DON’TS
Mountain Series
Installation and Operation Manual
VENTING DO’S AND DON’TS
When installing a Wood Stone Mountain Series oven there are some basic guidelines to follow regarding oven venting
that will help ensure proper operation and performance of the gas burners on the oven. These guidelines will also help
prevent damage to the oven's gas and electrical components due to improper venting and installation. Damage caused
by improper venting and installation is not covered by the oven warranty. This information applies to all Wood Stone
Mountain Series (MS) ovens equipped with one or more gas burners.
Most Wood Stone Mountain Series ovens are built into some sort of wall structure or enclosure. This creates the potential
for different venting scenarios that can be detrimental to the operation and performance of the oven burners. Here are
some basic rules that to follow that will ensure a properly functioning oven installation. Illustrated examples are included
on the following pages.
RULE 1
The ONLY pathway for air to enter the space beneath the oven should be at the front of the oven at the perforated
opening in the oven Service Panel provided with the oven, or on ovens equipped with an optional Storage Box, through
the perforations provided on the oven Storage Box. This will eliminate the chance of air movement or cross drafts
beneath the oven that can disrupt the oven burners.
RULE 2
DO NOT block the flow of air through the front Service Panel. It is required to provide necessary combustion air to the
oven burners. Airflow and service access MUST be provided from the front of the oven only at this Service Panel. DO
NOT relocate the oven air intake (see Rule 1).
RULE 3
To ensure proper venting of the oven, you must use an appropriate exhaust fan as described in this manual. There must
also be an adequate source of make-up air provided to your kitchen space—the room that the oven opens into. The
make-up air supply should not point directly at the oven. Other than the oven Service Panel, do not provide make-up air
or other ventilation into an enclosure that surrounds the oven (see Rule 1). Without proper make-up air the oven, (or any
gas equipment), will not vent and operate correctly.
Please review the illustrations on the following pages.
An ongoing program of product improvement may require us to change
specifications without notice. WS-MS-(4, 5, 6, 7)-RFG-IR,
Revised May 2015.
Doc no: M0033.03
18
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
VENTING DO’S AND DON’TS
Mountain Series
Installation and Operation Manual
DIRECT CONNECT VENTING EXAMPLES
Equal air pressure inside and
outside of oven room
Stud wall
Facade
surface
Air intake area
on removable
Service Panel
properly
exposed
Exhaust
flow
direction
is normal
Example 1 shows a proper installation.
The enclosure around the oven is
completely sealed so that the only air
entering the space beneath the oven
comes through the oven Service Panel.
Intake air flows
through designed
intake vents in the
Service Panel to
oven burners
1 Acceptable venting
Equal air pressure
inside and outside of
oven room
Facade material
improperly placed
over oven air
intake
Exhaust
flow
direction is
normal
Example 2 is not acceptable because
the combustion air intake is blocked,
preventing combustion air from reaching
the oven burners. The burners will not
function properly, and will lead to damage
of oven components.
Insufficient
combustion air
resulting in burner
problems & poor
oven performance
2. Unacceptable venting
An ongoing program of product improvement may require us to change
specifications without notice. WS-MS-(4, 5, 6, 7)-RFG-IR,
Revised May 2015.
Doc no: M0033.03
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
19
VENTING DO’S AND DON’TS
Mountain Series
Installation and Operation Manual
DIRECT CONNECT VENTING EXAMPLES
Neutral room
air pressure
Equal air pressure
inside and outside of
oven room
Low pressure is created
by HVAC or any air
moving equipment
outside the oven room
Exhaust flow
direction is
reversed
Exhaust air is pulled
backwards through
oven burners
An added vent
intended to increase
air supply
Airflow to oven is
altered as air moves
from normal to low
pressure
Example 3 shows an incorrect
installation where an additional vent
was added to the wall behind the oven,
creating an air pressure difference
causing air movement beneath the oven
and disrupting the operation of the oven
burners. This air movement can be so
severe as to cause a downdraft, pulling
the exhaust down the oven flue and
backwards through the burners, leading
to heat damage of oven components.
3. Unacceptable venting
Low pressure area
Air flow
False ceiling
Exhaust
flow
direction is
reversed
Combustion air is
diverted from oven
burners because
room is open to a
low pressure area.
Exhaust air is
pulled backwards
through oven
burners.
Example 4 shows an incorrect
installation where the enclosure
surrounding the oven is open to the
attic space above the ceiling. Air
can move rapidly through the space
enclosing the oven to the lower
pressure area within the attic space.
This can cause a downdraft situation
at the oven, pulling air and heat
backwards through the oven burners,
leading to damage of oven components.
4. Unacceptable venting
An ongoing program of product improvement may require us to change
specifications without notice. WS-MS-(4, 5, 6, 7)-RFG-IR,
Revised May 2015.
Doc no: M0033.03
20
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
VENTING DO’S AND DON’TS
Mountain Series
Installation and Operation Manual
DIRECT CONNECT VENTING EXAMPLES
Low pressure area
Air flow
Equal air pressure inside and
outside of oven room
Exhaust
flow
direction
is nomal
False ceiling
Addition of an
oven room ceiling
isolates the
oven from low
pressure areas
thus equalizing
air pressure and
allowing normal
airflow to the oven
burners.
Example 5 shows a correct installation
where a ceiling has been added to the
enclosure surrounding the oven to correct
an improper installation.
5 Acceptable venting
An ongoing program of product improvement may require us to change
specifications without notice. WS-MS-(4, 5, 6, 7)-RFG-IR,
Revised May 2015.
Doc no: M0033.03
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
21
VENTING DO’S AND DON’TS
Mountain Series
Installation and Operation Manual
HOOD INSTALLATIONS
In addition to the information given for installations using the direct connect venting method, the following information
applies to installations where the oven is being vented using a Listed Type 1 hood. Also refer to the OVEN VENTING
section earlier in this manual.
PROPER MOUNTING POSITION FOR THE WOOD STONE HOOD
1. Center the hood from side to side on the oven (A). Note that in an MS-5, 6 or 7 model, the oven may have the round
flue adapter attached. The adapter can prevent the proper positioning of the hood. The flue adapter is attached with
screws. Simply remove the screws to remove the adapter if it is in the way.
2. Pull the hood forward so that the notch (B), as viewed from the side of the hood, lines up with the front edge of the
top of the oven.
3. Secure the hood to the top of the oven using #10 self-tapping screws. The flanges on the hood are pre-drilled (C).
Screw directly into the top of the oven to secure the hood.
4. Attach grease-rated duct to the outlet on the hood. The hood captures over the oven flue collar and oven doorway.
No connection is made to the oven flue collar.
An ongoing program of product improvement may require us to change
specifications without notice. WS-MS-(4, 5, 6, 7)-RFG-IR,
Revised May 2015.
Doc no: M0033.03
22
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
VENTING DO’S AND DON’TS
Mountain Series
Installation and Operation Manual
HOOD INSTALLATION WITH DECORATIVE FACADE WALL/OVEN ENCLOSURE
For installations where a hood is being used with a decorative facade wall or oven enclosure, it will be necessary to both
seal the gap between the facade wall and the top of the oven, and the gaps at the sides of the hood between the facade
wall and the front of the oven. This will prevent air from being pulled up the sides of the oven from below by the hood. It
will also prevent debris, etc. from falling into the facade wall.
Flashing piece
by installer
Acceptable venting
Additional flashing detail
Wall stud
Shield
flashing
to be
flush
with
top of
oven
Note that the hood extends out beyond the face of the
oven. DO NOT extend the oven facade wall into the oven
hood. The wall beneath the hood must stop at the top
of the oven. To allow for proper function of the hood,
filter removal and hood maintenance, you must provide
a minimum of 8 inches of clearance between the front
face of the facade wall and the front of the hood.
Acceptable venting
An ongoing program of product improvement may require us to change
specifications without notice. WS-MS-(4, 5, 6, 7)-RFG-IR,
Revised May 2015.
Doc no: M0033.03
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
23
VENTING DO’S AND DON’TS
Mountain Series
Installation and Operation Manual
Incorrect installation. No flashing has
been installed so air being pulled up the
sides of the oven from beneath.
Unacceptable venting
Exhaust stack
Stud wall
Side view of
properly installed hood
Hood
Airflow
shield
Facade
surface
Acceptable venting
An ongoing program of product improvement may require us to change
specifications without notice. WS-MS-(4, 5, 6, 7)-RFG-IR,
Revised May 2015.
Doc no: M0033.03
24
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
VENTING DO’S AND DON’TS
Mountain Series
Installation and Operation Manual
CLEARANCES
The Type 1 hood requires an 18-inch clearance to combustible construction. Clearances to limited combustibles may be
reduced per NFPA 96 and/or your local codes. Approved clearance reduction methods may also be used, per NFPA 96
and/or your local codes. (These reductions are applicable to the hood and/or duct only, NOT to the oven.) Consult with
your local inspector regarding approved methods.
Any facade wall 6" to either side of the oven doorway and above MUST be of non-combustible construction with no
exceptions.
Shaded areas must be
of non-combustible
construction.
Maintain 18" clearance to combustible
construction from hood. Clearance
reduction methods described in NFPA 96
may be used subject to the approval of
the authority having jurisdiction.
Any facade wall six inches from either
side of the doorway and above (as
shown in green) must be of noncombustible construction.
All installations subject to the approval of the local authority having jurisdiction. Wood Stone recommends you
submit your venting plans in advance to your local authority for approval.
An ongoing program of product improvement may require us to change
specifications without notice. WS-MS-(4, 5, 6, 7)-RFG-IR,
Revised May 2015.
Doc no: M0033.03
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
25
ASSEMBLY
Mountain Series
Installation and Operation Manual
1. Mount the oven mantle (if provided) using the hardware provided. Please refer to the MANTLE MOUNTING section.
2. Mount the stainless steel toe kick to the front of the oven stand, angle side down using the large self tapping screws.
The holes are pre-drilled in the stand. If your oven is equipped with a Service Panel extension or storage box, a toe
kick is not necessary. Refer to assembly diagrams in the pages that immediately follow.
3. Mount the service/intake panel to the brackets on the front of the stand, directly below the doorway, using the screws
provided. See the FRONT PANEL ASSEMBLY section. If your oven was shipped with the optional facade extensions,
see EXTENSION PANEL ASSEMBLY section.
NOTE: This panel is the only access for servicing the gas and electrical components of the oven so it must be
left accessible and removable. Do not obstruct the flow of combustion and ventilation air through the perforation
provided on the front panel.
4. The following applies to stucco finish ovens only (models ending with “-S”): Once the oven has been set in place,
cover wire mesh and metal lathing with no less than 1 inch of stucco (see STUCCO APPLICATION section for diagram
and stucco formula).
An ongoing program of product improvement may require us to change
specifications without notice. WS-MS-(4, 5, 6, 7)-RFG-IR,
Revised May 2015.
Doc no: M0033.03
26
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
MANTLE MOUNTING
MANTLE MOUNTING
Mountain Series
Installation and Operation Manual
The initial steps are the same for mounting either a stainless mantle or a bracket for a granite mantle.
1. Begin by installing the threaded studs
into the clip nuts below the oven
doorway (3 or 4 turns is sufficient).
2. Position the mantle (or bracket) on the
oven, making sure the rear flange rests
on the floor of the oven (you may need
an extra pair of hands).
3. Place one stainless steel washer and a
cap nut onto each stud. Tighten the cap
nuts so the mantle is securely held in
place.
4. Using the high temperature silicone
(provided), fill any gaps between the
oven hearth and the mantle flange.
Gaps between the mantle flange and
the stainless steel doorway frame
may also need to be filled with a small
amount of the silicone sealant. Clean
up any sealant before it dries.
INSTALLATION OF GRANITE
After completing the steps outlined above, apply a generous amount of silicone adhesive (provided) to the top of the steel
mantle bracket.
Put the stone in place and apply light
pressure to seat it properly. Make sure
that the angle in the granite lines up with
the angle in the bracket. Allow the sealant
to set for several hours before filling
any gap between the stone slab and the
metal bracket with the silicone sealant
(provided). Clean up any sealant before
it dries.
An ongoing program of product improvement may require us to change
specifications without notice. WS-MS-(4, 5, 6, 7)-RFG-IR,
Revised May 2015.
Doc no: M0033.03
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
27
FRONT PANEL ASSEMBLY
Mountain Series
Installation and Operation Manual
STANDARD FRONT PANEL AND TOE KICK ASSEMBLY INSTRUCTIONS
Flame Height Control Knob
Controller
D
D
B
C
D
C
B
D
D
D
D
A
A
D
A
Service Panel
Transformer Box
Contains terminal strip for incoming power supply.
NOTE: Have licensed electrician make this electrical connection.
A Hex-head self-tapping screw. Used to
attach Toe Kick. 5 total.
B Phillips head 1/4-20 screw. Used to attach
Service Panel to Controller bracket. 2 total.
C Phillips head #10 screw. Used to attach
Service Panel to Throttle Knob Bracket. 2 total.
D Phillips head self-tapping screw. Used to
secure the sides of the Service Panel. 8 total.
SERVICE PANEL THROTTLE ASSEMBLY
The Flame Height Control Knob position
can be adjusted inward or outward by
loosening the Clamp and sliding the
throttle knob assembly to the desired
position. Be sure to retighten the Clamp
once the Flame Height Control Knob is
in the desired position.
An ongoing program of product improvement may require us to change
specifications without notice. WS-MS-(4, 5, 6, 7)-RFG-IR,
Revised May 2015.
Doc no: M0033.03
28
Throttle Valve
Throttle Bracket
(already attached)
Clamp
Cotter Pin
EMT Throttle Rod
Extension
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
Pointer
Collar/
Pointer
Flame Height
Control Knob
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
EXTENSION PANEL ASSEMBLY
Mountain Series
Installation and Operation Manual
OPTIONAL LOWER EXTENSION, THROTTLE ROD AND CONTROLLER ASSEMBLY INSTRUCTIONS
1.After the oven has been leveled, remove
the Extension Panel Throttle Assembly
which has been attached to the inside
of the stand for shipping. Position the
Lower Extension Assembly onto the front
of the oven. It will rest on the guides
that are welded to the oven legs. Attach
the assembly to the oven legs using the
supplied 1/4-20 nuts, bolts and washers.
2.Remove the Front
Access Panel.
Throttle Valve
Extension Panel
Throttle Assembly
3.Attach the Controller
to the mounting bracket
of the Extension using
the 1/4-20 bolts
provided.
Throttle Bracket
(Attached to Extension)
Cotter Pin
EMT Throttle
Rod Extension
Clamp
Pointer Assembly:
Pointer & Pointer Collar
Flame Height Control
(Throttle) Knob
4.Remove the Flame Height Control Knob & Pointer Assembly from the Throttle Assembly. Slip the Clamp off
of the Throttle Knob Assembly and slide it over the EMT throttle rod extension. Slip the front of the EMT
Throttle Rod through the Throttle Rod Bracket at the front of the oven, then slip the other end of the EMT
onto the Throttle Valve at the back of the oven. Note: The end of the EMT that goes over the Throttle Valve
is drilled to accept a Cotter Pin. Attach the EMT Throttle Rod Extension to the Throttle Valve using the Cotter
pin and open the end of the pin slightly to prevent it from falling out. Make certain the valve is in the full
OPEN position by turning the attached Throttle Rod Extension counterclockwise until it stops.
Continued
An ongoing program of product improvement may require us to change
specifications without notice. WS-MS-(4, 5, 6, 7)-RFG-IR,
Revised May 2015.
Doc no: M0033.03
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
29
EXTENSION PANEL ASSEMBLY
Mountain Series
Installation and Operation Manual
OPTIONAL LOWER EXTENSION, THROTTLE ROD AND CONTROLLER ASSEMBLY INSTRUCTIONS
5.Pass the Throttle Rod through the Throttle Bracket (already attached). Position
the Pointer in approximately the 2 o’clock position. Slide the Clamp on the EMT
over the end of the Throttle Rod/Knob assembly and attach the Throttle Rod to the
EMT Throttle Rod Extension using the compression Clamp (5/16" nut). On curved
Facade Extensions, make to leave at least 1/8" of space between the end of the
Pointer and the Bracket when it is set to a horizontal position.
6.Reinstall the Front Panel. Secure the Controller with a 1/4-20 screw at the top
and bottom.
Use (2) #10 stainless steel sheet metal screws to secure the Front Panel to the
Throttle Bracket.
1/8"
minimum
clearance
between
Pointer &
Bracket
Pointer
Collar Set
Screws
An ongoing program of product improvement may require us to change
specifications without notice. WS-MS-(4, 5, 6, 7)-RFG-IR,
Revised May 2015.
Doc no: M0033.03
30
7. CALIBRATING THE POINTER
Loosen the Pointer Collar Set Screws using a 3/16"
Allen wrench. Position the attached Pointer to “5” on the
Flame Height Index Scale. Tighten the Pointer Collar in
this position. Make certain the tip of the Pointer is at least
1/8" away from the Index Scale at the tightest point of
the rotation of the Knob so it does not scrape.
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
STUCCO APPLICATION
Mountain Series
Installation and Operation Manual
This figure depicts the
application of stucco on a
Wood Stone oven.
Use no less than one inch
of stucco coating to cover
all exposed metal lathing
on the oven.
Maintain a minimum
of 14" clearance from
top and 1" from side
of the appliance to all
combustible surfaces.
TRADITIONAL
STUCCO MIX
1 part masonry cement
1 part regular cement
5 parts sand
Stucco premix is available
at your local lumber yard
or building supply store.
Follow stucco
manufacturer’s instructions
for correct mixing
information.
MINIMUM STUCCO
APPLICATION IS 1"
An ongoing program of product improvement may require us to change
specifications without notice. WS-MS-(4, 5, 6, 7)-RFG-IR,
Revised May 2015.
Doc no: M0033.03
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
31
CONTROLLER
Mountain Series
Installation and Operation Manual
CONTROLLER FUNCTIONS
Power indicator light
Indicates the oven is
turned ON.
Dome Flame
indicator light
Indicates the pilot
for the radiant flame
has lit.
Hearth Heat indicator light
Indicates that the pilot for the
Underfloor IR burner is lit. This
light will go off whenever the
hearth temperature is above
the Hearth Set Point.
POWER DOMEHEARTH
FLAMEHEAT
Hearth Temperature display
Displays temperature of
oven floor (hearth). Sensor is
embedded 1" below hearth
surface.
HEARTH
TEMPERATURE
Hearth Set Point display
Indicates set point
temperature of
Underfloor IR burner
On/Off button
Press to turn oven on/off
HEARTH SET POINT
Push ON/OFF
button to light
burners.
Presser le bouton
ON/OFF pour
allumer le bruleur.
ON
OFF
Push ON/OFF
button to turn
burners off.
Presser le bouton
ON/OFF pour
arreter le bruleur.
F
C
WAIT 5 MINUTES BEFORE RELIGHTING
ATTENDRE 5 MINUTES AVANT DE RÉALLUMER
1-800-988-8103
An ongoing program of product improvement may require us to change
specifications without notice. WS-MS-(4, 5, 6, 7)-RFG-IR,
Revised May 2015.
Doc no: M0033.03
32
Arrow buttons
Pressing appropriate
directional arrow to
adjusts Hearth Set Point
temperature up or down.
Temperature unit selector
Toggles between Fahrenheit
and Celsius temperature
scales in display screens
www.woodstone-corp.com
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
INITIAL START-UP
Mountain Series
Installation and Operation Manual
INITIAL OVEN START-UP PROCEDURE
IMPORTANT: If at any time you feel that either or both of the burners are not operating properly, turn the oven off
and call for service. Before servicing, disconnect the electrical supply at the breaker and turn off the gas supply at the
appliance’s individual gas shutoff valve. In the event of a power failure, no attempt should be made to operate the oven.
Your oven was cured at the factory. However in the course of shipment, storage on site, etc. the ceramic materials will
have absorbed moisture. It is critical that the procedure below be followed to ensure that this moisture is driven from the
ceramic in a controlled fashion. This will minimize cracking and prevent damage to the oven that could otherwise occur
by bringing the oven to temperature rapidly the first time it is used. This initial procedure need only be followed the first
time the oven is fired and/or if the oven has not been used for an extended period of time.
BEFORE GETTING STARTED
1. Make sure main gas supply is on (valve parallel with gas line).
2. Make sure the switches on the Honeywell control gas valves are in the ON position. These are located beneath the
oven.
3. Make sure that the venting system has been tested and approved for operation and is on.
FIRST DAY
1. Remove the Night Heat Retention Door(s). Push the ON/OFF button on Controller. It may take awhile for the gas to
purge all the air from the gas lines.
2. Allow oven to operate at the factory settings for 1 hour (Hearth Set Point at 100 °F, radiant flame at its lowest setting).
Leave the Hearth Set Point at 100° F throughout the entire first day.
3. After one hour, raise radiant flame to 25% (~6 inch flame, “2” on the Flame Height Index Scale) using the Flame
Height Control Knob. Hold this setting for 4 hours.
4. After 4 hours at 25% flame, raise to 50% flame (“3” on the Flame Height Index Scale) using the Flame Height Control
Knob and hold for at least another 4 hours or until the temperature reaches 500 °F.
5. Once the temperature reaches 500 °F the oven is ready for use. If you will be shutting the oven down, see the
instructions that follow.
TURNING OFF THE OVEN
1. Push ON/OFF button. All gas will go off, including the pilots. Put the Night Heat Retention Door(s) in place to retain
heat.
NOTE: Always wait 5 minutes before restarting the oven. Never run the oven with the Night Heat Retention Door(s)
in place.
NOTE: Small “crazing” cracks will occur with normal heating and cooling. They will not effect the performance or durability
of the oven. If cracks of 1/8" or more develop, contact Wood Stone for evaluation.
An ongoing program of product improvement may require us to change
specifications without notice. WS-MS-(4, 5, 6, 7)-RFG-IR,
Revised May 2015.
Doc no: M0033.03
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
33
DAILY OPERATION
Mountain Series
Installation and Operation Manual
DAILY OVEN OPERATION OVERVIEW
THIS OVEN IS NOT FOR USE WITH SOLID FUEL
DAILY OPERATION
1. Remove the Night Heat Retention Door(s).
2. Push ON/OFF button, adjust the Hearth Set Point on the Controller to the desired floor temperature. Using the Flame
Height Control Knob, turn the radiant flame to its highest setting. Check your temperature after approximately one
hour. If you are close to your desired temperature, reduce your flame to the holding flame setting that corresponds
to your desired temperature. See the FLAME HEIGHT CONTROL section that follows to determine the proper setting
that will correspond to your desired temperature. Note: It is only possible to program the Hearth Set Point for the
underfloor IR burner to temperatures from 100–800 °F. Once proper temperatures for your application have been
established, there should be little or no need to change the Hearth Set Point. The Hearth Temperature readout will
display “LO” until the oven floor reaches 100 °F.
ADJUSTING THE RADIANT (DOME) FLAME
To adjust the radiant flame: The radiant flame is always on (when the oven is operating) and can be adjusted to any
flame intensity between its highest and lowest setting. Simply turn the Flame Height Control Knob located to the lower
left of the doorway, beneath the mantle. This burner is the primary heat source for the oven. The infrared underfloor
IR burner acts as an assist, to maintain desired floor temperatures during periods of high food production.
TURNING OFF THE OVEN
1. Push the ON/OFF button. All gas will go off, including the pilots.
2. Put the Night Heat Retention Door(s) in place to retain heat.
Note: Always wait 5 minutes before restarting the oven. Never run the oven with the Night Heat Retention Door(s)
in place.
DURING THE FIRST FEW DAYS OF OPERATION, SMALL AMOUNTS OF WATER MAY APPEAR DRIPPING FROM
THE OVEN. THIS IS NORMAL AND WILL STOP WITHIN A FEW DAYS.
An ongoing program of product improvement may require us to change
specifications without notice. WS-MS-(4, 5, 6, 7)-RFG-IR,
Revised May 2015.
Doc no: M0033.03
34
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
FLAME HEIGHT CONTROL
Mountain Series
Installation and Operation Manual
DETERMINING THE APPROPRIATE FLAME HEIGHT
For each specific configuration of oven there is a system that determines what the desired flame height will be. Each
flame height corresponds to a saturated floor temperature. Several factors need to be accounted for in order to determine
this relationship for each oven.
USING THE FLAME HEIGHT INDICATOR SCALE
Heat Up Flame: Set the Flame Height Pointer at “5” (highest setting) on the Flame Height Index Scale until desired
temperature is reached.
Holding Flame: Using the Flame Height Control Knob, set the flame height to “3” (~8–9" flame) on the Flame Height
Index Scale for desired temperature of 570–600 °F. Set the flame height to “2” (~5–6" flame) for desired temperature
of 450–480 °F.
Cooking Flame: After introducing the pizza/product into the oven, visually raise the flame to approximately 3 inches
higher than the Holding Flame.
Return the Flame Height Control Knob to the Holding Flame position after removing the pizza/product from the oven.
THE COOKING FLAME HAS TWO PURPOSES:
1. To bake the top of the pizza/product as fast as the bottom of the pizza/product.
2. To help replace heat to the floor (hearth) that is lost during production cooking.
Note: The settings recommended on the Flame Height Index Scale for specific flames are based on ovens that have been
installed according to specifications. Individual results may vary slightly.
FLAME HEIGHT INDICATOR
Comprised of two parts
Flame Height Index Scale
Flame Height Control Knob
An ongoing program of product improvement may require us to change
specifications without notice. WS-MS-(4, 5, 6, 7)-RFG-IR,
Revised May 2015.
Doc no: M0033.03
For more information regarding Flame Height
Control, go to the Resource Center section of
our web site at:
www.woodstone-corp.com
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
35
MAINTENANCE
Mountain Series
Installation and Operation Manual
CLEANING THE OVEN
Clean as needed­—multiple times per hour depending on production. Wood Stone recommends the use of long-handled
brushes for sweeping up surface debris that will accumulate on the floor of the oven during use. Use a natural fiber
brush, always brushing away from the radiant burner well to the doorway where it can be easily removed with a dough
cutter or spatula. For deeper cleaning, use a brass bristled brush. The oven floor can be then cleaned with a damp (not
wet) rag wrapped around the brush head.
Wood Stone offers an assortment of oven brushes available through your dealer. Specification sheets may be viewed on
the Wood Stone website under Tools & Accessories.
NEVER PLACE ANYTHING IN OR ABOVE THE RADIANT FLAME.
NEVER SWEEP DEBRIS INTO THE RADIANT BURNER. THIS CAN CAUSE THE BURNER TO CUT OUT, DAMAGE
BURNER COMPONENTS, AND/OR EFFECT BURNER PERFORMANCE. PROBLEMS CAUSED BY DEBRIS IN THE
RADIANT BURNER WILL NOT BE COVERED BY THE OVEN WARRANTY.
NEVER USE ICE, EXCESSIVE WATER, ANY LIQUID, OR ANY TYPE OF CLEANING CHEMICAL ON THE OVEN FLOOR.
DOING SO CAN SEVERELY DAMAGE THE OVEN CERAMIC AND THIS DAMAGE WILL NOT BE COVERED UNDER
WARRANTY.
NIGHT HEAT RETENTION DOORS
The door(s) are used for nighttime heat retention. Do not operate the oven with doors in place.
Night Heat
Retention Doors
An ongoing program of product improvement may require us to change
specifications without notice. WS-MS-(4, 5, 6, 7)-RFG-IR,
Revised May 2015.
Doc no: M0033.03
36
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
PERIODIC THERMAL CLEANING
Mountain Series
Installation and Operation Manual
ESTABLISHING A THERMAL CLEANING SCHEDULE
Wood Stone ovens are typically operated at temperatures which preclude the need for cleaning of the interior walls and
ceiling (the dome) of the oven. If, however, you routinely operate the oven at floor temperatures lower than 450 °F, you
may notice a buildup on the interior walls and/or ceiling of the oven. If this is the case, use the following procedure to
periodically clean the oven. The frequency of thermal cleaning will be determined by the amount of buildup experienced.
THERMAL CLEANING
If a Wood Stone gas-fired oven is operated at low temperatures (below 450 °F), it is possible that grease from food could
condense on the walls and ceiling of the oven. To remove the grease that has accumulated on the walls and ceiling of the
oven, simply turn the radiant flame to its highest setting. Monitor the floor temperature displayed on the Controller. When
the floor reaches 600 °F, lower the flame slightly so as to maintain the oven floor temperature near 600 °F for about
an hour. Once the oven dome appears clean, allow the oven to return to normal operating temperatures and continue
normal operation.
An ongoing program of product improvement may require us to change
specifications without notice. WS-MS-(4, 5, 6, 7)-RFG-IR,
Revised May 2015.
Doc no: M0033.03
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
37
TROUBLESHOOTING GUIDE
Mountain Series
Installation and Operation Manual
PROBLEMCAUSE/SOLUTION
Controller will not turn on
1. Incoming power to oven turned off. Check circuit breaker for circuit
supplying the oven. Check that any wall switches external to the oven
that control oven power are turned on. Check that any interlocks
external to the oven are turned on.
2. If Controller still does not turn on, please contact Wood Stone for
assistance.
Radiant flame does not light
1. Is gas turned on to the oven? Is gas shut-off valve turned all the way
on?
2. Debris in burner. Burner may require cleaning. Contact Wood Stone for
assistance.
3. Damaged igniter or gas valve. Contact Wood Stone for assistance.
If the oven is being started for the first time:
Has all air been bled from the gas line?
Is the switch on the SV-2 valve in the ON position?
NOTE: Valve is located beneath the oven at the rear, towards the side
where the radiant burner is located.
Underfloor burner is not running.
“Hearth Heat” light is off.
Hearth temperature is above the Hearth Set Point.
Hearth Temperature is above the
Hearth Set Point.
This is normal. Radiant (dome) flame can drive the temperature over
the Hearth Set Point. The Hearth Set Point only controls the underfloor
(hearth) IR burner. Turn down the dome flame if needed.
“Chec” display on Controller
Underfloor IR burner did not fire when the floor temperature dropped below
the Hearth Set Point. Contact Wood Stone for assistance.
Please contact Wood Stone at 1-800-988-8103 should service be necessary, or if you have any questions about
your oven. Our service hours are 8am to 4:30pm Pacific Time. Follow the recorded instructions for Emergency
Service if you require assistance during non-business hours. A Wood Stone technician will promptly respond
to your call.
An ongoing program of product improvement may require us to change
specifications without notice. WS-MS-(4, 5, 6, 7)-RFG-IR,
Revised May 2015.
Doc no: M0033.03
38
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
OPERATION SEQUENCE
Mountain Series
Installation and Operation Manual
BURNER OPERATION SEQUENCE
RFG-IR OVEN - TYPE 2 CONTROLLER
Power on.
SV-2 valve powers Igniter and opens
Pilot valve to Radiant (rear) burner.
Pilot lights.
Pilot does not light, SV-2 times out.
SV-2 senses Pilot
flame – Igniter off, SV-2
opens, Burner lights,
Dome Flame Indicator
light comes on.
Floor temperature above
Hearth Set Point –
No action.
Floor temperature below Hearth
Set Point – Controller sends
power to SV-1 valve, SV-1
powers Igniter and opens
Pilot valve.
Pilot does not light – SV-1
times out, Controller
flashes “chec”.
Radiant burner remains
on until oven Controller
is turned off.
Pilot lights, SV-1 senses Pilot
flame, Igniter off, SV-1 opens,
Underfloor IR Burner lights,
Hearth Heat light on.
Floor reaches the Hearth Set
Point temperature, Controller
turns off power to SV-1 to turn
off Underfloor IR Burner.
An ongoing program of product improvement may require us to change
specifications without notice. WS-MS-(4, 5, 6, 7)-RFG-IR,
Revised May 2015.
Doc no: M0033.03
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
39
120 VAC ELECTRICAL DIAGRAM
Mountain Series
Installation and Operation Manual
RFG-IR 120 VAC MODELS WIRE DIAGRAM
TYPE 2 CONTROLLER
IR w/ RFG
Temperature Controller
Control Panel Type 2
Thermo
Couple
2
5
P
8
4
6
TB1
Red
Yellow
red
orange
pink
white
brown
yellow
TB4-R
TB4-Y
TB3-2
TB3-5
TB4-P
TB4-8
TB3-4
TB3-6
GND
green
TB-A
L
N
G
TB3
TB1-2
TB1-6
TB1-4
TB1-5
Red
2
6
4
4
5
Yellow
Brown SV1
Infrared
XFMR
TB4-8
CB 4A
TB4-P
TB4
TB1-R
TB1-Y
GND
110-120 VAC
50-60Hz
wired by others
TB1-8
XFMR
XFMR
R
Y
8
8
P
Brown
Thermo
Couple
TB1-P
Orange
White
SV2
Radiant
White
Brown
DIAG #:
DATE:
Bellingham, WA +1(360)650-1111 www.woodstone-corp.com
An ongoing program of product improvement may require us to change
specifications without notice. WS-MS-(4, 5, 6, 7)-RFG-IR,
Revised May 2015.
Doc no: M0033.03
40
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
WD064 Rev. 0
3/28/2014
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
240 VAC ELECTRICAL DIAGRAM
Mountain Series
Installation and Operation Manual
RFG-IR 240 VAC MODELS WIRE DIAGRAM
IR w/ RFG EM-2V
Temperature Controller
Control Panel Type 2
TB1
Red
Yellow
2
red
5 orange
P pink
8 white
4 brown
6 yellow
Thermo
Couple
green
TB-A
L
N
G
TB4-R
TB4-Y
TB3-2
TB3-5
TB4-P
TB4-8
TB3-4
TB3-6
GND
TB3
TB1-2
TB1-6
TB1-4
TB1-5
Red
2
6
4
4
5
Yellow
Brown
SV1
Infrared
XFMR
TB4-8
Fuse F1 - 5A
TB4-P
TB4
TB1-R
TB1-Y
GND
220-240 VAC
50-60Hz
wired by others
TB1-8
XFMR
XFMR
R
Y
8
8
P
Brown
Thermo
Couple
TB1-P
Orange
White
White
SV2
Radiant
Brown
DIAG #:
DATE:
Bellingham, WA +1(360)650-1111 www.woodstone-corp.com
An ongoing program of product improvement may require us to change
specifications without notice. WS-MS-(4, 5, 6, 7)-RFG-IR,
Revised May 2015.
Doc no: M0033.03
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
WD065 Rev. 0
7/17/2014
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
41
INTERLOCK DIAGRAM
Mountain Series
Installation and Operation Manual
INTERLOCK OF OVEN CONTROL TO AN EXHAUST FAN
This connection is intended to interrupt power to the oven until the fan is turned on.
Wired by others
120 VAC Oven Circuit
120 VAC Fan Circuit
S1
120 VAC
to Oven
120 VAC
to Fan
S1 is a Double Pole, Single Throw (DPST)
switch provided by others.
S1 is a double pole, single throw switch (provided by others) that interrupts in-coming power to both the oven and the
fan. The intent is to prevent the operation of the oven’s gas burner in the event the fan is shut off.
Any interruption of the power to the oven will cause the oven (including all burners and pilots) to shut off, and it will be
necessary to restart the oven by pressing the start switch once power is restored.
For additional interlock options, see the Wood Stone Interlock Options supplement in the Manuals section on the website,
woodstone-corp.com, or contact Wood Stone for additional information.
An ongoing program of product improvement may require us to change
specifications without notice. WS-MS-(4, 5, 6, 7)-RFG-IR,
Revised May 2015.
Doc no: M0033.03
42
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
LIMITED WARRANTY
Mountain Series
Installation and Operation Manual
ALL WARRANTY SERVICE MUST BE PRE-APPROVED BY WOOD STONE
Wood Stone warrants its equipment to the original purchaser against defects in material or manufacture for a period of one
year from the original date of purchase, subject to the following exclusions and limitations.
Please contact the factory first at 1.800.988.8103 or 1.360.650.1111, seven days a week. Our normal business hours are 8am
to 4:30pm PST Monday–Friday. If calling during non-business hours, follow the recorded instructions for emergency service
and a Wood Stone technician will get back to you promptly.
EXCLUSIONS
The warranties provided by Wood Stone do not apply in the following instances:
1. In the event that the equipment is improperly installed. Proper installation is the responsibility of the installer; proper installation
procedures are prescribed by the Wood Stone Installation and Operation Manual.
2. In the event the equipment is improperly or inadequately maintained. Proper maintenance is the responsibility of the user;
proper maintenance procedures are prescribed in the Wood Stone Installation and Operation Manual. Burner problems resulting
from debris or ash in the burner well will not be covered by the warranty. Call with questions regarding maintenance frequency.
3. In the event that the failure or malfunction of the appliance or any part thereof is caused by abnormal or improper use or is otherwise
not attributable to defect in material or manufacture.
4. In the event that the appliance, by whatever cause, has been materially altered from the condition in which it left the factory.
5. In the event that the rating plate has been removed, altered or obliterated.
6. On parts that would be normally worn or replaced under normal conditions.
7. Normal cracking due to expansion and contraction stress relief in the ceramic firebox.
8. In wood-fired equipment configurations, in the event that pressed log products of any type have been burned in the equipment.
9. In coal-fired oven configurations, in the event any type of coal other than anthracite coal fuel has been used.
10.Damage resulting from the use of chemical cleaning products in the oven, as well as any damage from liquids or chemicals, including
water, being poured or sprayed into the oven.
If any oral statements have been made regarding this appliance, such statements do not constitute warranties and are not part of the
contract of sale. This Limited Warranty constitutes the complete, final and exclusive statement with regard to warranties.
THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER WRITTEN, ORAL OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR PARTICULAR
PURPOSE OR WARRANTY AGAINST LATENT DEFECTS.
LIMITATIONS OF LIABILITY
In the event of warranty claim or otherwise, the sole obligation of Wood Stone shall be the repair and/or replacement, at the option of
Wood Stone, of the appliance or component or part thereof. Such repair or replacement shall be at the expense of Wood Stone with the
exception of travel over 100 miles or two hours, overtime, and holiday charges which shall be at the expense of the purchaser. Any repair
or replacement under this warranty does not constitute an extension of the original warranty for any period of the appliance or for any
component or part thereof. Parts to be replaced under this warranty will be repaired or replaced at the option of Wood Stone with new
or functionally operative parts. The liability of Wood Stone on any claim of any kind, including claims based on warranty, expressed or
implied, contract, negligence, strict liability or any other theories shall be solely and exclusively the repair or replacement of the product
as stated herein, and such liability shall not include, and purchaser specifically renounces any rights to recover, special, incidental,
consequential or other damages of any kind whatsoever, including, but not limited to, injuries to persons or damage to property, loss of
profits or anticipated profits, or loss of use of the product.
TO SECURE WARRANTY SERVICE
If you claim a defect covered by this Limited Warranty, contact:
Wood Stone Corporation, Attn: Service Department, 1801 W. Bakerview Rd., Bellingham, WA 98226 USA
Phone 1.800.988.8103 or 1.360.650.1111
An ongoing program of product improvement may require us to change
specifications without notice. WS-MS-(4, 5, 6, 7)-RFG-IR,
Revised May 2015.
Doc no: M0033.03
wood stone corporation
1801 w. bakerview rd.
bellingham, wa 98226 usa
tf.800.988.8103
t.360.650.1111
f.360.650.1166
[email protected] or visit woodstone-corp.com
43
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement