Crestron HD-XSP Quick Start
quickstart guide
HD-XSP
1
7.1 High-Definition Professional Surround Sound Processor
3
Introduction
The HD-XSP can be configured with the front panel controls or with Crestron Toolbox™. For details on
using Crestron Toolbox, please refer to the Crestron Toolbox help file. Otherwise, continue reading
below.
The HD-XSP is a 7.1 surround sound processor featuring multiple inputs and downmixing capabilities.
2
Hardware Hookup
The “Installer” menu is used to configure the HD-XSP’s inputs, outputs, network settings, and front panel
controls. To open the “Installer” menu:
Connect the Device
Make connections to the HD-XSP as shown in the following diagram.
HDMI OUT:
To HDMI Device
DIGITAL:
From Digital Audio Sources
HDMI
OUT
2
24V DC, 2.0A:
From AC Power Pack
OUTPUT
L
IN
1. Press HOME to display the “Crestron HD-XSP” screen as shown in the following diagram.
OUTPUT:
To Amplifiers
3
MIX
FRONT
L
R
+ - G + - G
L
R
+ - G + -
4
SURROUND
L
R
+ - G + - G
Configuration
BACK
L
R
+ - G + - G
HD-XSP
SERIAL LABEL
MAC ID LABEL
CENTER - SUB
C
S
+ - G + - G
Crestron
—
24V --2.0A
DOWNMIX
L
R
+ - G + - G
G
R
DIGITAL
5
INPUT
6
BALANCED
LAN
2. Press BACK to display the “Password” screen.
INPUT:
From Unbalanced Analog
Audio Sources
HDMI IN:
From HDMI Source
INPUT:
From Balanced or Unbalanced
Analog Audio Source
LAN:
10BASE-T/100BASE-TX
Ethernet to Lan
Password
[0]000
Connect Balanced/Unbalanced Input & Outputs
One balanced/unbalanced audio input and four balanced/unbalanced audio outputs are provided, utilizing 5-pin and 6-pin
terminal block connectors respectively. For connection details, refer to the following diagrams.
Balanced Input
Balanced Output
(Center & Sub)
Balanced Output
L
R
+ - G + -
L
R
+ - G + - G
C
S
+ - G + - G
•
To select a number, press ˄ or ˅.
•
To move the cursor left or right, press ˂ or ˃.
When the password is displayed, move the cursor to the rightmost digit and press SELECT. The
“Installer” menu is displayed.
Shield
Shield
3. Use the ˄, ˅, ˂, ˃, and SELECT buttons to enter the password.
Installer
Shield
+ Right
+ Right
AMP
L
R
+ - G + - G
Shield
+
+
+ Left
Left
The “Installer” menu is divided into four sections.
+ Subwoofer
AMP
Shield
Control
C
S
+ - G + - G
+ Right
Right
+ Center
Unbalanced Output
(Center & Sub)
Unbalanced Output
L
R
+ - G + -
Network
AMP
•
Inputs: Set the name and compensation level of each input.
•
Outputs: Set the audio parameters for the theater and downmix outputs.
•
Network: Configure and view the HD-XSP’s Ethernet settings.
•
Control: Configure and view the HD-XSP’s front panel settings.
For details, refer to the latest version of the HD-XSP Operations & Installation Guide (Doc. 7446).
+ Center
(Continued in following column)
1
For details, refer to the latest revision of the
HD-XSP Operations & Installation Guide, Doc. 7446.
www.crestron.com
QUICKSTART DOC. 7447A (2035044)
Specifications subject to
change without notice.
05.13
NOTE: The default password is 0000. For instructions on
changing the password, refer to “Password” in the latest
version of the HD-XSP Operations & Installation Guide
(Doc. 7446), which is available from the Crestron Web site
(www.crestron.com/manuals).
888.273.7876
201.767.3400
HD-XSP
Unbalanced Input
Outputs
AMP
+ Left
+ Left
Inputs
+ Subwoofer
quickstart guide
HD-XSP
4
7.1 High-Definition Professional Surround Sound Processor
Operation
4
Operation (continued)
Select a Decoding Mode:
When power is applied to the HD-XSP, the title screen displays, followed by the “Current Source” menu. The
“Current Source” menu is used to select a source and a decoding mode.
1. Press ˄ or ˅ to highlight Decoding Mode and press SELECT. The “Decoding Mode” menu is
displayed, showing a list of supported decoding modes for the detected audio signal.
Select a Source or Decoding Mode
To select a source or decoding mode:
Decoding Mode
None
NOTE: The “Current Source” menu is displayed when power is applied to the HD-XSP.
Auto
1. Press HOME.
Dolby PLIIx Movie
2. Press SELECT. The “HD-XSP” menu is displayed.
Dolby PLIIx Music
HD-XSP
Source
2. Press ˄ or ˅ to highlight the desired mode and press SELECT. The display returns to the “Current
Source” menu showing the selected source and the selected decoding mode.
Theater
Downmix
Current Source
Display Off
HDMI
Decoding Mode
3. Press ˄ or ˅ to highlight Source and press SELECT. The “Current Source” menu is displayed.
Current Source
Source Select
Dolby Digital
Decoding Mode
Volume Control & Mute (Theater Output Only)
During operation, the theater output’s volume level can be adjusted or muted.
•
None
To adjust the theater output’s volume level, Press VOL ˄ or VOL ˅.
NOTE: The downmix output’s volume level is adjusted via control system programming.
Select a Source:
1. Press ˄ or ˅ to highlight Source Select and press SELECT. The “Source Select” menu is displayed.
•
Source Select
To mute the theater output, press MUTE. An indicator lights on the bottom of the display.
NOTE: The downmix output’s mute function is controlled from the front panel. Refer to the
latest version of the HD-XSP Operations & Installation Guide (Doc. 7446) for details.
HDMI
Optical
Coaxial 1
•
Coaxial 2
To unmute the theater output press MUTE.
2. Press ˄ or ˅ to highlight the desired source and press SELECT. The “Current Source” menu is displayed. If
a signal type is detected, the supported signal type is shown on the bottom of the display.
Additional Functions
Current Source
Controls for the theater output, downmix output and display are available from the “HD-XSP” menu.
For details, refer to the latest version of the HD-XSP Operations & Installation Guide (Doc. 7446).
HDMI
Decoding Mode
The specific patents that cover Crestron products are listed at patents.crestron.com.
Crestron, the Crestron logo, and Crestron Toolbox are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United
States and/or other countries. Other trademarks, registered trademarks and trade names may be used in this document to refer to either the
entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is
not responsible for errors in typography or photography.
Dolby Digital
This document was written by the Technical Publications department at Crestron.
©2013 Crestron Electronics, Inc.
2
For details, refer to the latest revision of the
HD-XSP Operations & Installation Guide, Doc. 7446.
www.crestron.com
QUICKSTART DOC. 7447A (2035044)
Specifications subject to
change without notice.
05.13
888.273.7876
201.767.3400
HD-XSP
NOTE: The downmix output’s mute function is controlled from the front panel. Refer to the
latest version of the HD-XSP Operations & Installation Guide (Doc. 7446) for details.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement