EZ-30.DP Install - Crimestopper Security Products

EZ-30.DP Install - Crimestopper Security Products
EZ-31DP/33DP/34DP 1-WAY SYSTEMS
EZ-64TW1/74TW2/84FM 2-WAY SYSTEMS
EZ-30DP Stand Alone unit
DP SERIES (Data port)
REMOTE ENGINE STARTING SYSTEM
INSTALLATION INSTRUCTIONS
INTRODUCTION
CONGRATULATIONS on your choice of a “EZEE Start” System by Crimestopper Security Products Inc. This booklet
contains the information necessary for installing your remote starter system. If any questions arise, contact your
installation dealer or Crimestopper Security Products Inc. at the Tech Support number below.
DISCLAIMER:
This installation book is designed for the installer or individual with an existing understanding of automotive electrical
systems, along with the ability to test and connect wires for proper operation. To ease installation, we suggest that you
READ THIS MANUAL before beginning your installation. This book is provided as a GENERAL GUIDELINE and the
information contained herein may differ from your vehicle. Crimestopper Security Products, Inc. and its’ vendors shall
not be liable for any accident resulting from the use of this product. This system is designed to be professionally
installed into a vehicle in which all systems and associated components are in perfect working condition.
TECHNICAL SUPPORT: (800) 998-6880
Monday - Friday 8:00am - 4:30pm Pacific Std. Time
Web Site: www.crimestopper.com
E-mail: [email protected]
CRIMESTOPPER SECURITY PRODUCTS, INC.
1770 S. TAPO STREET, SIMI VALLEY, CA. 93063
REV A 07.2005
This device complies with FCC Rules part 15. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference that
may be received, including interference that may cause undesired
operation. The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this equipment.
Such modification could void the user’s authority to use the
equipment.
TABLE OF CONTENTS
Pre-Installation Considerations……….………...……...……………………………………………………………….……2
Installation Cautions & Warnings………………….……………………………………………………………….…..……3
Wiring……..…………………………....……………………………………………………………………………….…….3-7
Wiring High-Current Connector…….………………...………………………………………………………………….....8-9
Power Door Lock Wiring...………………………………………….…………….……..…………...………………..…10-11
Smart Tachless, Tach Reference, Tach Finder, & Timed Crank Modes…………………..…..………...…...……12-15
Diesel Glow Plug Delay..………………….…………………………………...……………………...…..…………………16
Options Programming ………..……………………….…………………………………...……………..………………16-21
Transmitter / Transceiver Programming,2 Vehicle Operation.……………………………………………………….22-23
Troubleshooting “Before You Call” Section……………..…………………………..………………….………….………24
Jumper Pin, Antenna, & System Diagrams…………………………………………………………..………….….…25-27
PRE-INSTALLATION CONSIDERATIONS
BEFORE BEGINNING, check all vehicle manufacturer cautions and warnings regarding electrical service (AIR BAGS,
ABS BRAKES, ENGINE / BODY COMPUTER AND BATTERY).
PLAN OUT YOUR INSTALLATION and determine most suitable locations for all components to be placed. These
components include: the module itself, valet/program button, possible relays, and antenna/receiver (EZ31DP/33DP/34DP, EZ64TW1/74TW2/84FM only, the EZ-30DP model does not include antenna or remotes.) Allow
enough wire to create a service loop with strain relief, should servicing be required. This will also allow easier access
and mounting.
DAMAGE to the EZEE Start unit resulting from incorrect installation or failure to follow guidelines stated in this book will
not be covered under warranty and will be subject to repair or replacement charges.
USE A VOLT/OHM METER to test and locate all connections. Test Lights can damage a vehicle’s computer systems.
ADDITIONAL PARTS, which are not included with this unit, may be needed for your particular vehicle. These items
may include extra relays or Anti-Theft System Bypass modules.
2
INSTALLATION CAUTIONS & WARNINGS
**FOR SAFETY REASONS, DO NOT INSTALL in vehicles with MANUAL TRANSMISSIONS.** If accidentally left in
gear, a remote started vehicle could become a self-propelled threat to life and property.
DO NOT extend the Remote start ignition harness length. Mount the module so that main harness reaches all ignition
switch wiring. Extending these wires could result in poor or improper performance.
DO NOT route any wiring that may become entangled with brake, gas pedals, steering column or any other moving parts
in the vehicle.
DO NOT exceed the rated output current of any circuit on the Remote start module. Failure to observe this warning will
result in damage to the unit not covered under warranty.
DO NOT remote start the vehicle in a closed garage! Make sure that the garage door is open or there is adequate
ventilation. Failure to observe this rule could result in injury or death from poisonous Carbon Monoxide fumes.
WIRING
PIN 1: YELLOW/WHITE: (-) HORN CHIRP/HONK OUTPUT
Connect to the LOW CURRENT Negative Horn Trigger wire usually located near the steering column. If the vehicle horn
circuit requires +12, then a relay is required. RELAY WIRING: Connect the Yellow/White wire to terminal #85, connect
relay terminals #86 and #87 to +12V constant power. Connect terminal #30 to the +12V positive Horn activation wire.
PIN 2: BLACK: MAIN SYSTEM GROUND
Connect to chassis metal of the vehicle. An existing bolt or screw may provide an adequate ground, or drill a small hole,
scrape away paint and attach using a sheet metal screw & star washer. This wire must be connected to a proper ground
or undesirable and inconsistent operation will occur. Do not use Factory ground locations.
PIN 3: YELLOW/BLACK: (-) IGNITION OUTPUT -or- ANTI-GRIND/STARTER DISABLE OUTPUT
This negative output wire is programmable and can function two different ways. It can be used as a Negative Ignition
output for GM Anti-theft and Transponder Bypass modules, or it can be programmed to function as an Anti grind/Starter
Disable output. As a Negative Ignition wire, this wire turns on when the remote start button is pressed and stays on
through the duration of the remote start. As an Anti grind/Starter disable this wire activates when the Lock button on the
remote is pressed and during remote start. When using this wire for an Anti grind/Starter disable, an optional Relay is
needed to interrupt the Starter circuit. The starter disable circuit adds an anti-theft feature to this remote start system
and prevents accidental grinding of the starter if key is turned too far after a remote start. See diagrams on NEXT
PAGE.
3
WIRING
PIN 3: YELLOW/BLACK FOR NEGATIVE IGNITION OUTPUT: (Relay and/or Module not included)
ANTI-THEFT/
TRANSPONDER
MODULE
OR
YELLOW/BLACK
OR
Diode isolate
if using both!
85
86
30
87
+12V CONSTANT
3rd IGN
(If needed)
IGN SW.
PIN 3: YELLOW/BLACK: FOR ANTI-GRIND/STARTER DISABLE OUTPUT: (Relay not included)
TO
MOTOR
IGN 1
IGN 2
ACC
START
CUT
BROWN
YELLOW/BLACK
85
86
MAKE CERTAIN TO CONNECT "BROWN" START OUTPUT WIRE TO
MOTOR SIDE OF ANTI-GRIND/START DISABLE RELAY.
MAKE SURE 86 TERMINAL HAS POWER WITH IGNITION ON AND CRANK
4
WIRING
PIN 4: BROWN: (-) AUX OUTPUT (TRUNK POP) or DOME LIGHT ILLUMINATION OUTPUT
This output is programmable for two modes of operation. See Programming Option Section.
Mode (1) DEFAULT: Provides a Ground pulse when button #3 (Trunk) on the remote transmitter is pushed to activate
a factory electric trunk release or other optional accessory.
Mode (2) ALTERNATE: Provides a Ground output for 30 seconds when the unlock button is pressed for use as a
dome light illumination output.
Note when using the Brown wire as a Trunk Pop, you may also need or want to program option #14 so the system
also provides an Unlock signal when the trunk pop is activated. This may help to prevent unnecessary triggering
of Factory Alarm systems or you may want the convenience of having the door unlock at the same time.
BROWN WIRE: TRUNK OUTPUT or DOME LIGHT
+12V CONSTANT
BROWN
85
86
30
87
+12V CONSTANT
OR *
Trunk Soleniod
(Default)
-ORDome Light
Circuit
* Test activation circuit in vehicle.
Connect to+12V for Positive circuits
or Ground for Negative circuits. Relay
not included.
5
WIRING
PIN 5: GREEN: (-) START ACTIVATION INPUT, OEM
INTERFACE or TURBO TIMER INPUT
EZ-30 EXPANSION (Default)
See descriptions & diagrams below.
Mode (1) [Default (-) Neg. Start Activation] This wire
allows a host (or parent) alarm’s or keyless entry system
to activate a Remote Start by sending a 1-Second
Negative signal to the Green input wire to trigger a
remote engine start or stop. Connect the Green wire to
the host system’s Auxiliary channel output wire.
Mode (2) [Alternate OEM Interface] This mode allows
the system to Remote Start or Stop when 3 successive
Negative pulses are sent to the Green input wire.
Connect the Green input wire to the Negative lock signal
wire of the factory system. If your Factory OEM system
does not have this type of signal, then a relay is
required.
GREEN
1 sec. (-) pulse
AFTERMARKET
ALARM / KEYLESS
(Aux Channel
Output)
EZ-30 OEM INTERFACE
GREEN
3 Consecutive
(-) pulses
FACTORY KEYLESS
MODULE
TURBO TIMER INPUT [No programming required] This
New TURBO TIMER MODE
wire allows the system to keep a vehicle running for 1-5
Momentary
minutes [selectively] after removing the key. This mode
Switch
requires the use of a momentary switch that is not
GREEN
included with the kit. Connect a 2-pole momentary
switch with one side to chassis Ground and the other
(Not included)
side to the Green input wire. If you own a turbo or turbo
diesel vehicle, you can now allow the EZEE Start
system to keep your engine running for 1-5 minutes after
exiting/locking your vehicle to cool-down without the need for an external “Turbo Timer”.
NOTE: The turbo timer button will also trigger a remote start if it is inadvertently pressed when the
vehicle is not running. Please note this when installing the button and choose a location out of harm’s
way
.
6
WIRING
PIN 6: GRAY: (-) NEGATIVE HOOD PIN SWITCH (REQUIRED FOR PROGRAMMING)
Connect the Gray wire to a switch that is at ground when the hood is open. If an existing switch is not available, then we
recommend one to be installed. When this wire is grounded, the remote start is inhibited. If hood is opened on a remote
started engine, the unit will immediately shut the motor off. The unit will not attempt to start if hood is open. The hood
pin is also used for remote transmitter programming.
PIN 7: PINK: NEGATIVE GLOW PLUG
Connect Pink wire to indicator circuit that shows a (-) Signal while the “WAIT TO START LAMP” is on. When this wire is
used, the system will wait until light turns off before attempting a remote start.
PIN 8: PURPLE: (+12V) BRAKE RESET
Connect the Purple wire to the side of brake pedal switch that shows +12 volts ONLY when pedal is depressed. This is
the wire that turns off the remote start once the driver’s key is in the Ignition and turned to the ON position.
PIN 9: ORANGE/BLACK: (-) OEM DISARM OUTPUT
This wire provides a Ground pulse to disarm the vehicles' Factory anti-theft system prior to a Remote Start. Connect this
wire to the vehicles' anti-theft disarm wire. This wire is sometimes found coming off the Driver's door key switch or at the
Factory Anti-theft control module. This wire may not be needed if Factory Security only requires a door unlock pulse.
PIN 10: ORANGE: (-) OEM REARM OUTPUT
This wire provides a ground pulse to rearm the vehicles' FACTORY anti-theft system after a timed-out or aborted remote
start. Connect this wire to the vehicles' anti-theft rearm wire or to the door pin circuit depending on your requirements.
This wire may be needed to pulse the door pin circuit on vehicles with retained accessory power.
PIN 11: RED/WHITE: TACHOMETER INPUT
When installing the system in Tach mode, this wire must be connected to a valid source of AC voltage. This wire allows
the unit to sense the engine running and control the starter motor. See TACH REFERENCE MODE.
PROGRAM/OVERRIDE SWITCH: 2 PIN PLUG (REQUIRED FOR PROGRAMMING & LEARNING REMOTES)
This switch is used for programming features, transmitters, valet mode, and to override the optional starter disable (if
installed) in the event of a non-operating remote control.
LED: 2 PIN PLUG (OPTIONAL)
The LED is used as a VALET/PROGRAMMING indicator and it will also FLASH for use as security deterrent when the
optional ANTI-GRIND/STARTER DISABLE output is programmed.
WIRING: 7-PIN HIGH-CURRENT CONNECTOR
7
BROWN: +12V STARTER OUTPUT 30A:
Connect to circuit in the vehicle that has power ONLY while the STARTER MOTOR is CRANKING.
GRAY: +12V ACCESSORY OUTPUT 30A:
Connect to circuit in the vehicle that provides Accessory Power for systems such as HEAT and A/C. Typically, this wire
turns ON with the first position of the key, DROPS OUT WHEN CRANKING, then returns as the engine starts and runs.
(2) RED: +12V POWER INPUT WIRES (30A Fused):
Connect to both of these leads to +12V Constant Power. We recommend the BATTERY POSITIVE
TERMINAL.
PINK: +12V IGNITION OUTPUT 30A:
Connect to circuit in the vehicle that provides true Ignition Power for systems such as Spark and Fuel. Typically, this
wire turns ON with the second position of the key, STAYS ON WHEN CRANKING, and continues ON as the vehicle
runs.
PINK/WHITE: +12V MULTI-FUNCTION OUTPUT 30A (JUMPER SELECTABLE):
This is an optional multi-function output wire the can be configured as a Second IGN, ACC or STARTER output. Some
vehicles require more than just one IGN, ACC, or STARTER wire in order to start and run successfully. If this is the
case for your particular vehicle, then use the jumper pin located under the access panel on the top of the EZEE Start
control module to configure this wire to suit your needs. The DEFAULT setting is IGNITION. See Jumper Pin Diagram.
WHITE: +12V or (-) NEGATIVE PARKING LIGHT OUTPUT:
Connect to vehicle parking light circuit at the back of light switch or if this is not possible, connect directly to one of the
parking lights at the front of the vehicle. If your vehicle has a multiplex lighting system that requires a (-) Negative
parking light output, then open the access door on the top of the module and move the jumper. See Jumper Pin section.
Some European vehicles require separate left and right circuits. Use a dual relay or diodes to isolate the output. Note
the current limit on the Negative parking light output. You may require an external relay to prevent damage to the unit.
(1) Default parking light output is +12 volts.
(2) Use an external relay for vehicles that draw excess current from extra running lights, light bars, or trailers.
Parking light output is limited to (+) 10 amps or (-) 500 mA only.
SEE DIAGRAM on NEXT PAGE
8
WIRING: 7-PIN HIGH-CURRENT CONNECTOR
7-PIN High Current
Diagram not to scale,
for illustration purposes
only. Your vehicle may
differ.
Connector
TOP
PARKING
LIGHTS
RED
FUSE
30A
FUSE
WHITE
RED
+10A or 500mA (-)
FUSE
30A
PINK/WHITE
FUEL
PUMP
+
ENGINE
ECU
+
PINK
BROWN
GRAY
VEHICLE
BATTERY
STARTER
-
COIL
IGN
START 2
IGN 2
ACC
OR
ACC 2
IGN. SWITCH
H/V/AC
IF NECESSARY
NOTE: Heavy duty/High Current Ignition circuits greater than 30 AMPS. Industrial vehicles, dual AC, etc. require highcurrent relays. DO NOT use the outputs of the Remote Starter for High-Current systems or you will risk damaging the
unit and creating a hazardous condition! Use Part #CS-403 relays for circuits up to 70 amps.
9
POWER DOOR LOCK WIRING CONNECTOR
PIN 1: BLUE: (-) Negative pulse for UNLOCK
PIN 2: RED: +12V When using external relays (TERM 86)
PIN 3: GREEN: (-) Negative pulse for LOCK
Crimestopper Door Lock Accessories:
CS-6600DLM: Dual-relay plug-in module for Reverse
Polarity, Positive, or Aftermarket Motors.
CS-6500DLI: Plug-in pulse inverter that converts the
Negative outputs of the system to Positive type for Positive
Door Lock systems.
CS-610S1: Aftermarket door lock actuator (motor).
DETERMINING DOOR LOCK TYPE: We recommend
determining the type of locking system the vehicle has before
connecting any wires. Incorrect connection may result in
damage to the alarm and/or vehicle locking system. Door lock
information is provided as a guide. Your vehicle may differ.
Negative Trigger (-): Many Imports; Late model Ford & General Motors
Negative trigger door lock systems send a Negative (Ground) pulse to existing factory relays to lock and unlock the
vehicle doors.
Positive Trigger (+): Many General Motors; Chrysler / Dodge / Plymouth
Positive trigger door lock systems send a Positive (+12V) pulse to existing factory relays to lock and unlock the
vehicle doors.
Reverse Polarity: Many Ford/Lincoln/Mercury/Dodge/Chrysler/Plymouth and early 90’s GM Trucks
Reverse Polarity systems use no relays, but instead the door lock/unlock motors are controlled directly from the lock
and unlock switches in the door. The lock and unlock wires rest at Negative Ground when not in use. When the
lock or unlock button is pressed, one of the circuits is “Lifted” and replaced with +12V causing a lock or unlock to
occur.
Single Wire (Dual Voltage): Late model Chrysler/Dodge/Plymouth Vehicles, some 2000-UP GM
Dual Voltage systems have lock/unlock switches that send varying levels of Positive voltage OR Negative ground
current to the SAME wire for both lock and unlock. When the vehicle’s Body Computer Module (BCM) or door lock
module senses different voltages on this wire, the system will either lock or unlock. Single wire door lock systems
require relays and resistors.
Databus Systems 2003-UP GM Trucks & SUV’s, ‘96-04 Jeep Grand Cherokee
Databus systems send low current “Data messages” to the door lock controllers on a network in order to lock and unlock
the vehicle. To install aftermarket systems in these vehicles, an interface module is required that converts the regular
lock/unlock pulses into “Data messages” to allow locking & unlocking. Interface modules are sold separately.
10
BASIC DOOR LOCK DIAGRAMS
NEGATIVE TRIGGER DOORLOCK WIRING
POSITIVE TRIGGER DOORLOCK WIRING
GREEN
GREEN
RED
RED
BLUE
BLUE
FUSED
+12V
+
85
86
87
87A 30
FACTORY
POWER
LOCKING
RELAYS
L
UL
87
87A 30
FACTORY
POWER
LOCKING
UL
RELAYS
AFTERMARKET MOTOR/DOOR LOCK WIRING
GREEN
GREEN
FUSED
+12V
+
RED
BLUE
85
86
87
87A 30
85
85
86
86
87
87A 30
87
87A 30
CUT
L
FUSED
+12V
+
RED
BLUE
MASTER
SWITCH
UL
86
L
REVERSE POLARITY DOOR LOCK WIRING
+
85
CUT
11
85
86
87
87A 30
“SMART TACHLESS” MODE
Your EZEE Start system includes a unique voltage monitor called “Smart Tachless” mode. This mode allows this unit to
efficiently start an engine without the use of a tach signal wire. These modules actively monitor the voltage level of the
vehicle to control the starter motor each time a remote start is requested.
IMPORTANT NOTES:
(1) SETUP may be required for the EZEE Start “Smart Tachless” Mode. If your vehicle has not been at rest for a period
of time (Hot engine), then you must drain the surface charge from the battery. Unplug main power harness from unit,
turn HEADLIGHTS ON for 4 minutes to drain off excess surface charge on vehicle’s battery then reconnect.
(2) On the rare occasion that “Smart Tachless” mode does not operate satisfactorily, change the voltage reference level
as described below, or use a different mode such as “Tach” mode, or “Timed Crank” mode.
“SMART TACHLESS” ADJUSTMENT:
In the event “Smart Tachless” over-cranks or under-cranks your starter, the settings can be changed. The purpose of
adjusting the “Smart Tachless” Mode is to raise or lower the voltage reference threshold from the 93% default point.
Raising or lowering this 93% point should increase or decrease your cranking time respectively. The adjustment range
is from 80% to 100% in one percent increments. Follow steps below to adjust the reference level.
1.
2.
3.
4.
Open hood (or ground Gray wire if no hood pin is installed)
Turn the key to the ON position (Pink wire must be connected!)
Press program button 5 times, after a few seconds the unit will flash the lights and/or honk horn 5 times.
Carefully press the program button 21 times to get to option level 21. You must get a light flash and/or horn honk
after each press. If the lights didn’t flash and/or horn does not honk, then the unit did not register your button press.
Only count the light flash and/or horn honk.
5. Press the Lock Button #1 on the remote to decrease by 1% (lights will flash and/or horn honk 1X for each press);
Press the Unlock Button #2 to increase by 1% (lights will flash and/or honk horn 2X for each press); Press the Trunk
Button #3 to reset to 93% (lights will flash 3X). The unit will stop providing light flashes when you reach the bottom
(79%) or the top (100%) of the adjustment range. If you lost track, then just press Button #3 to reset back to 93% and
begin raising or lower again.
6. Turn Ignition OFF, Close hood (or un-ground the Gray wire) and check operation.
NOTE: This Smart Tachless adjustment feature is not available on the EZ-30DP Model that has no remote
transmitters or antenna. If you must use this feature on the EZ-30DP, then a remote and an antenna module
from an EZ-31DP/33DP/34DP must be used to set the desired level. Once programmed, remove antenna.
12
TACH FINDER & USEFUL TIPS
TACH FINDER MODE:
This Tach Finder mode can assist in locating a Tach source for your installation. When following the steps, the unit will
begin to flash the parking lights if you have the Red/White wire connected to a tach source. If lights do not flash, then try
another wire until you locate a tach signal that will cause the Parking lights to flash. NOTE: On some vehicles equipped
with daytime running lights, it may be difficult to see any flashing parking lights. In this case your only notification will be
the slight “ticking” sound coming from the module’s flashing light relay.
TACH FINDER STEPS:
1. Open hood (or ground Gray hood pin wire if no hood pin is installed)
2. Start Engine with the key. (Pink wire must be connected!)
3. Press the Program button for 2 seconds
4. Lights will begin flashing if the Red/White wire is connected to a valid tach source. If not try a different tach wire.
5. Once Tach is located then turn off engine and close hood to abort (Remove Gray wire from ground).
6. Now follow the Tach Programming steps.
TACH FINDER TIP: Cold Weather / High Idle Simulation:
The tach finder mode can also be used to help determine how your EZEE Start system may operate in a cold
weather situation. Once you have a valid tach source programmed into your system, follow test steps below.
1. Go back into the tach finder mode.
2. You should have a consistent light flash (like directional or emergency flashers).
3. Slowly raise the RPM level on your vehicle to simulate a “warm-up idle” that is higher than the normal idle level. If and
when the lights STOP flashing. Means that this is the point at which the tach signal is out of range of the system.
4. We recommend that you bring the RPM level up to between 1000 and 1500 RPMs to simulate a cold morning idle.
5. If the lights stop flashing too quickly, then we recommend using another tach source. This may help prevent the engine
from starting and stalling in the morning or cold weather.
TACH PROGRAMMING & TACH SIGNALS
13
INTRODUCTION
Tach signals will vary in levels and frequencies depending on many factors including the type of vehicle and the source
of the signal. The signals from a vehicle’s injector wire and coil pack wire can vary greatly even on the same engine.
The tach signal from an engine can also be affected by other sources such as electronic noise from the ignition or
computer modules. Recent improvements have been made to the circuitry to allow this EZEE Start system to sense a
wider range of tach signals than previous models.
TACH MODE
The Tach mode provides reliable remote starting performance through engine speed (RPM) sensing. When using Tach
Reference Mode, the Red/White wire is used for Tach signal [Engine RPM] input. Most modern engines include various
points where the Engine Speed [Tach] or A/C signal may be obtained. Tach Signal examples: Negative (-) side of
ignition coil, at the Distributor or Ignition Control Module, Coil Pack, Engine Computer, or Crankshaft Sensor.
Sometimes Fuel injectors, and Alternator stator pins can be used. These Tach Signal locations mentioned are provided
as a guide. Your vehicle may differ. Some locations will NOT be a good location for Tach source due to RF noise or
Computer Data.
TACH PROGRAMMING:
1. Open hood (or ground Gray hood pin wire if no hood pin is installed.)
2. Red/White wire should be connected to a valid Tach source.
3. Start engine with key. (Pink wire must be connected!)
4. Press program button 5 times, then wait for 5 light flashes and/or 5 horn honks.
5. Push program button more once. (You must get one light flash and/or honk after button is pressed.) This unit is
now at option #1-Tach Learning.
6. Press the #1 Lock Button on remote transmitter. The unit will read the Tach source and flash the lights and or
honk once for program confirmation. (On EZ-30DP models without remote transmitters, press the brake pedal in
this step.)
7. If lights do not flash for confirmation, then try another tach source or try the tach finder to locate another wire
EXAMINING THE TACH FREQUENCY WITH A DIGITAL MULTI-METER
If you own a Digital Multi-Meter meter with a frequency counter setting, it can be helpful to measure and research the
range of tach signal from your particular engine. When probing your chosen tach wire, observe the frequency reading
from the meter at both the warm/low engine idle and cold/high engine idle points. Tach signals ranging between 70Hz
and 700Hz are desired. If your tach wire has readings that are not in this range, the unit may not operate properly. The
frequency of the tach wire in this range does not guarantee operation. If you cannot locate a good tach source from your
engine, then you can switch your EZEE Start system to the “Smart Tachless” or “Timed Crank”.
14
TIMED CRANK MODE
This feature provides an easy method of starting the vehicle without locating an exact tach wire. The system uses a
timed cranking output combined with the use of the Red/White tach wire as an engine ON/OFF monitor. The Red/White
Tach wire must still be used in this mode of operation. THIS FEATURE MUST BE PROGRAMMED BEFORE USE!
THERE ARE 2 LEVELS of programming required: First, set the system for “Timed Crank” operation, and secondly you
may need to adjust the amount of cranking time. There are 4 different crank times available for use. SEE OPTION
PROGRAMMING CHART ON PAGE 17-18 FOR SETTINGS.
HOW TO USE THIS FEATURE:
1. Go to the “Programmable Options” section of this manual, and turn “ON” Option #15 "Timed Crank". (It is normally on
Tach Monitor)
2. With “Timed Crank” turned ON, you will STILL have to connect the Red/White Tach wire to a tach source on the
engine. The Red/White Tach wire becomes a simple “Engine Monitor”. Although the unit will not be using the
Red/White wire to start the motor, it will be using this wire to determine whether the motor is running or not. This is a
mandatory connection. A “crude” or “less exact” tach source can be used only when in “Time Crank” mode.
3. Using the vehicle key, start the engine a few times to get a “feel” of how long the cranking time is. Once the “Timed
Crank” mode is turned on, the default cranking time is set to a default of 0.50 seconds. We recommend beginning
with this setting. Try a remote start and see if the cranking is appropriate for your vehicle
4. If 0.50 seconds is not an appropriate starter cranking time, then go to Programming Option #18 and change the crank
time setting to a longer value. The values are as follows: 0.5, 0.75, 1.0, and 1.5 seconds.
WARNING: This method of starting the vehicle is not as reliable as using regular “Tach” or Smart Tachless
modes. This method should be used only in the event that a tach wire cannot be located using the normal tach
programming and tach finder. When using this method, there may be certain operating anomalies requiring
seasonal adjustments. These are, but not limited to:
• Starter may under-crank in extreme cold weather. Vehicle may not start on 1st attempt and may require a 2nd or 3rd try.
• In warm weather when your vehicle may start very quickly, “Timed Crank” mode may tend to over-crank the starter.
• The only ways to correct the above issues are to go to Option #18 and adjust the cranking time.
• When in “Timed Crank” mode, the cranking time can only be adjusted manually through option #18. When the
system is in Tach or Smart Tachless modes the cranking time is controlled automatically by the microprocessor.
15
DIESEL GLOW PLUG DELAY
This feature provides a solution for diesel vehicles without having to connect to the Glow Plug-“Wait to Start Circuit”.
This may be needed for various reasons. If your vehicle does not have a viable “Wait to Start Circuit”, or you cannot
locate and identify the circuit, then change your system to “Diesel Glow Plug Delay” mode. You can choose from a
selection of “pre-cranking” delay times. Once this mode is activated, the system will NO LONGER monitor the PINK
glow plug input wire and will use a delay setting chosen by the installer in the option chart.
NOTES: This feature is OFF by default and must be programmed before use. Once this feature is turned ON, the Pink
Glow plug input wire is not used. The Remote start unit will always wait the programmed time before cranking EVEN IF
the glow plug warms up first. There are 3 different Delay times available for use: 10, 20, or 30 seconds. SEE OPTION
PROGRAMMING CHART on Pages 17-18.
HOW TO USE THIS FEATURE:
1. See the “Option Programming” section on Pages 17-18 and change Option #19 from "Monitor Glow Plug Light" to
one of the delayed time values. (Default setting is to always monitor the PINK Glow Plug input wire.)
2. Once this option has changed, the system will wait for the selected time before cranking.
OPTIONS PROGRAMMING
This EZEE Start unit has over 20 programmable control options to customize the system for various operating features
and installer preferences. Examine the chart on the pages 17-18 along with reading the descriptions that follow on
pages 18-21. You may change one option at a time, or program multiple options in one session. If you start with the
lowest option and continue on to higher options, you do not need to repeat steps #1-3 each time. For example, you can
change Option #2 to “ON”, then you can continue pressing the program button to get to a higher number option and
change it as well. You can only go from low to higher options numbers in one session.
OPTION PROGRAMMING CHART BEGINS ON NEXT PAGE
16
OPTIONS PROGRAMMING
To Engage Option Programming:
1. Open hood (If no hood pin switch is installed, then ground the Gray wire)
2. Turn Key to the ON position. (Do not start vehicle) Pink wire must be connected!
3. Press the program / valet button 5 times. Wait for the unit to flash the lights and/or horn honk 5 times.
4. Push the valet/program button the number of times that corresponds to the option number desired (1-22X). You
must get a light flash and/or honk after each button press. If the system did not flash the lights and/or honk, then
it did not register your press. Press carefully and do not lose count.
5. A) For EZ-30DP/31DP/33DP/34DP or 64TW1/74TW2/84FM: When you reach the desired option #, Press
button #1(Lock) or #2 (Unlock) to change the option. (Some option numbers use ALL 4 remote buttons to select
settings)
5. B) For EZ-30DP: (No remotes) Tap the brake pedal to toggle through the option values: Tap the brake once
(lights flash 1X; Tap the brake pedal again (Lights flash 2X) tap 3 or 4 times for options that have 3 or 4 values.
6. When finished, turn Ignition OFF, close hood (or un-ground Gray wire) and check for changed features.
* = Default Value
Option # Option Description
Option Values
Button #1
Button #2
LOCK
UNLOCK
1.
Engine Monitoring
Tach (Engine RPM) or Tachless
Tach
Tachless*
2.
Autolock with RPM/Ignition
ON or OFF.
ON
*OFF
3.
Door Lock Pulse Time
0.75 Sec. (Standard) OR
3 Sec.
*0.75 Sec.
3.0 Sec. (European Vacuum)
4.
Double Unlock Pulse
Single or Double Unlock Pulse
Double
*Single
5.
OEM Interface
Remote Start w/Single Pulse or 3
3 pulse
*1 Pulse
Pulses on Green input wire
(EZ-30 MODEL ONLY)
Double button press for remote
6.
ON or OFF
ON
*OFF
start and Trunk release
7.
8.
9.
10.
Horn Chirps on remote start
Lock During and After
Remote Start Abort
Tan Wire Output function
“Wake up” Pulse on Unlock
(1-sec +12V to IGN)
ON or OFF
ON or OFF
Trunk or Dome Light Output
ON or OFF
17
ON
OFF
*OFF
*ON
Dome
ON
*Trunk
*OFF
OPTIONS PROGRAMMING
11.
12.
13.
N/A - Not used
Yellow/Black Wire (-)
Horn Chirp Confirmation with
1 or 2 presses
Unlock/Disarm with Trunk pop
activation
N/A – Not used
(-) IGN output or (-) Anti-Grind
ON or OFF
16.
17
18.
Timed Crank Mode or
Tach Monitor
Adjustable Horn Pulse
OEM Disarm/Unlock Pulse
Starter Cranking Time
(Only when option #15 is set
for “Timed Crank”)
19
Diesel Glow Plug Delay
20.
Remote Start Engine Run
Time
21.
Smart Tachless Voltage
Adjust 79-100%
(Only when Option #1 is set
to “Tachless”)
22.
Option reset
14.
15.
Anti-Grind
OFF
*IGN output
*ON
Trunk Pop & Unlock or Trunk Pop
Only
Trunk Pop &
Unlock
*Trunk Pop
Only
Timed Crank: Pre set crank time
Tach Monitor: Use Tach Pulses
0.02 sec. Normal or 0.04 Longer
0.75 sec. Normal or 0.5 Shorter
Button #1 = 0.75 Sec.
Button #2 = 0.5 Sec.
Button #3 = 1.0 Sec.
Button #4 = 1.5 Sec.
Button #1 = 10 Sec.
Button #2 = Monitor Glow plug
Button #3 = 20 Sec.
Button #4 = 30 Sec.
Button #1 = 12 Min.
Button #2 = 24 Min.
Button #3 = 36 Min.
Button #4 = 48 Min.
Button #1 = Decrease by 1%
increment
Button #2 = Increase by 1%
increment
Button #3 = Reset to 93% (Default)
Button #2
Timed
Crank
Long
Short
0.75 Sec
*Tach
Monitor
*Normal
*Normal
*0.5 Sec
10 Sec.
* Monitor
Glow Plug
circuit
12 Min.
*24 Min.
-1%
+1%
18
Reset to
Default
OPTIONS PROGRAMMING
OPTION DESCRIPTIONS:
1. Engine Monitoring:
This option sets how the unit monitors your engine. You can program either for Tach mode in which the unit uses a
Tach signal (RPM) or for Tachless mode that monitors voltage level. See pages 11-15 for more information and
additional steps for actual Tach learning and Tach finder modes.
2. Auto Lock/Unlock (Improved):
The option controls whether the doors will automatically lock/unlock on your vehicle when driving or with turning the
Ignition ON/OFF. If the Auto Lock feature is turned on, and the system is in Tach mode, then the doors will lock as the
engine RPM’s increase (driving). If the Auto Lock feature is turned on, and the system is in Smart Tachless mode, then
the doors will lock when the Ignition is turned on. When the Auto Lock feature is turned on, the system will unlock the
doors when the Ignition is turned off. With this feature OFF, the system will not automatically lock or unlock the vehicle.
3. Door Lock Pulse Time:
Controls the amount of time for lock/unlock pulse. The standard setting is 0.75 for most vehicles. A 3 sec. setting is
required for 1980’s/90’s European Vacuum or Pneumatic door lock systems.
4. Double Unlock Pulse:
The unit will send 2 unlock pulses when the #2 Unlock button is pressed. This feature may be required for interfacing
this alarm with an existing Factory Keyless Entry or Alarm system in a vehicle. These systems are found on some
Nissan, VW, Toyota, and Lexus vehicles.
5. OEM Interface (EZ-30DP Add-on Model):
This option controls the input selection for the Green Negative Start Trigger Wire. When using an Aftermarket Host
Alarm or Keyless Entry System: Leave the setting as “1 pulse” and connect the Green wire to the (-) Auxiliary output wire
of the Alarm or Keyless Entry System. For Factory Keyless entry systems (without a (-) Negative auxiliary output),
change the option to “3 Pulse” and tap the green wire into a Negative signal wire on the vehicle such as a Negative door
lock wire. Pressing the Factory remote lock button 3 times will produce 3 short negative signals to trigger a remote start.
6. Double Button Press for Remote start and Trunk release:
This option will allow you to change whether the Remote starter and Trunk release activate by a single ½ second
press or a double button ½ second press.
19
OPTIONS PROGRAMMING
7. Horn Chirps on Remote Start:
This option allows the unit to provide 3 short chirps for audible confirmation of a remote start. The horn output wire must be
connected for this feature.
8. Lock During/After Remote Start:
This option controls whether the unit will automatically lock during and after a remote Start abort or time-out.
9. Brown Output Wire Function: Trunk Pop or Dome Light Output
This option controls how the Brown output wire of the unit functions, either for Trunk pop or for Dome light illumination.
10. +12V “Wake up” Pulse:
This option allows the unit to provide a 1-second pulse on the Pink main ignition output when unlocking. The Ignition pulse serves
to “Wake up” vehicle control modules or body computers that “time out” or go into power saving mode. This is required on many
late model Ford vehicles with a “Slam” lock system in order to actually unlock the vehicle after it has been shut down for a short
period of time.
11. Not used
12. Yellow/Black Wire Function: (-) Negative IGN or ANTI-GRIND / Starter Kill Output
This option controls the units Negative multi-function output. Default: Negative IGN output that turns ON and stays on for the
duration of the remote start. Use this wire to turn on Anti-theft bypass adapters for GM or Transponder systems. When changed to
an Anti-Grind, this output activates when the Lock button on the remote is pressed and activates during a remote start. Anti-Grind
is designed for use with an optional Starter disable relay (Not included).
13. Horn Chirp with Lock and Unlock- 1 or 2 Button Press (When Optional Horn Output installed):
This option allows the system to chirp the vehicle horn for Lock/Unlock confirmation on 1 button press or a 2nd press within 3
seconds. The horn output must be connected to use this feature.
14. Unlock With Trunk Pop or Trunk Pop Only:
This option controls whether the system will provide an Unlock/Disarm pulse when the Trunk release is activated from the remote
control. This may be required to prevent unnecessary triggering of a factory alarm on some vehicles.
15. Timed Crank Mode or Tach Monitor:
This option controls whether the system uses a tach wire to control the starter or uses a pre-set starter cranking time.
16. Adjustable Horn Pulse:
Some vehicles require an extended horn pulse to activate the Factory horn. Use this option #16 to EXTEND the horn pulse
slightly.
20
OPTIONS PROGRAMMING
17. OEM Disarm / Unlock Pulse:
Some vehicles like Nissan and VW require a shorter setting to prevent the vehicle from attempting to roll down the
windows due to the length of the UNLOCK and/or DISARM pulses. Use this option to SHORTEN the OEM
Disarm/Unlock Pulses should your vehicle require this. Symptom: Windows will slightly vent or begin to roll down when
unlocking.
18. Pre-Set Starter Cranking Time: (Requires Option #15 to be set to “Timed Crank”)
This option controls the starter output cranking time. Choices are 0.5, 0.75, 1, or 1.5 seconds.
19. Diesel Glow Plug Delay:
This option controls the system’s Diesel vehicle interface. Using this option you can control whether the unit monitors
the vehicle’s glow plug circuit using the Pink input wire (Default), or you may select a specific delay time before cranking.
This option is helpful if you are unable to locate a glow plug signal. Just select a delay time and do not connect the Pink
Glow Plug wire. Selections: 10, 20, 30 seconds, or Monitor Pink Wire (Default).
20. Remote Start Run Time:
This option controls the engine run time for remote start. Use the buttons on the remote control to set a choice of 12, 24,
36, or 48 minutes. The default setting is 24 minutes.
21. Smart Tachless Voltage Adjustment:
This option controls the voltage reference point when using smart Tachless mode. Pressing the Lock or Unlock buttons
on the remote raises or lowers the reference level in 1% increments from 79%-100%. Button #3 resets the unit to the
factory default reference point of 93%. The default 93% setting works for most vehicles. See page 12 for additional
Smart Tachless mode information.
22. Option Reset: (RESTORE TO DEFAULT)
This option allows you to restore all programmable options to factory default values. Go to the option 22 and press the
Unlock Button #2 on the remote. The unit will flash the lights 2 times and all values will be reset to factory original
settings. Default values are marked with asterisks in the chart on pages 17-18.
21
TRANSMITTER PROGRAMMING
Transmitter Programming: (Excludes EZ-30DP model without remotes)
Notes: Remote Transmitters/Transceivers come pre-programmed from the Factory. When re-learning remotes or
adding remotes, ALL your system’s remote codes must be learned at time of programming!! These systems allow
storage of up to 4 different remote codes in memory. The EZ-64TW1/74TW2/84FM systems include both a 1-way
remote transmitter and an LED or LCD remote. The “Sidekick” transmitters for the 2-way systems are a special model
that is not compatible with standard EZ-31DP/33DP/34DP remotes. EZ-31DP/33DP/34DP and EZ-64TW1/74TW2/84FM
remotes are not interchangeable.
1.
2.
3.
4.
Open hood (ground the Gray hood pin wire if no hood pin is installed.)
Turn key to the ON position. (Do not start vehicle) Pink wire must be connected!
Press Program/Valet button 4 times. Wait for the unit to flash the parking lights and/or honk horn exactly 4 times.
EZ-30DP/31DP/33DP/34DP: Press Button #1 (Lock) or Press Start(EZ-31DP ) of the transmitter to be learned. EZ64TW1/74TW2/84FM: Both the Lock & Unlock buttons must be pressed. You should get 2 light flashes and 2 horn
honks indicating the code-learn. Now the unit is waiting for a 2nd code, so repeat this step as needed with up to 3
additional remotes. The unit will flash the lights in succession after each code learned for up to 4 codes. (3 flashes
for the 2nd code, 4 flashes for the 3rd code and 0 for 4th code.) If all 4 codes are learned, the unit will automatically exit
code learning mode, otherwise turn key OFF and close the hood.
IGN
OFF
WAIT FOR
4 FLASHES
(GRAY WIRE GROUNDED)
PRESS 4X's
EZ-31DP (USE START BUTTON) EZ-64TW1/74TW2
1-Way systems
(2-Way systems only)
IGN
OFF
FLASH 2, 3, or 4 X's
PRESS
LOCK ONLY
EZ-33/34DP
COMPLETE
LOCK &
UNLOCK
PRESS TOGETHER
22
2-VEHICLE OPERATION
The EZ START series can be used for 2 vehicle operation. A single remote can control two independent vehicles
with identical systems installed.
NOTE: The EZ-34/33/31DP and EZ-64TW1/74TW2/84FM systems ARE NOT interchangeable. An EZ-64TW1
system remote CANNOT control an EZ-74TW2 and vice versa!
See diagram below on how to switch your remote(s) to vehicle #2 operation. To set up the 2-Vehicle operation you
must first program your remotes to Vehicle #2. Follow the “Transmitter Programming” steps at the second vehicle
and learn YOUR remote, along with vehicle #2’s existing remotes.
For EZ-64TW1/74TW2
(Refer to operation manual.)
VEHICLE #2
Press side button
first, then you have
4 seconds to
control vehicle #2.
23
TROUBLESHOOTING: “BEFORE YOU CALL” SECTION
UNIT WILL NOT ATTEMPT TO START (KEYLESS ENTRY FUNCTIONS NORMALLY):
The unit is in Valet mode. Turn IGN ON, press and hold valet/programming button for 5-6 seconds then turn key off.
Unit is now out of valet mode and should remote start. If optional LED is installed, then it will be on solid when in Valet.
SYSTEM IS UNSUCCESSFUL AT REMOTE START DURING EXTREME COLD CONDITIONS:
Please be aware that during sub-freezing conditions your remote starter may take more that one attempt to start, or it
may not successfully start the vehicle after 3 attempts. During these conditions the vehicle may not properly start even
using the key, therefore trying to start by the remote would also be unsuccessful.
UNIT FLASHES LIGHTS ONCE AND WILL NOT ATTEMPT A START:
The unit senses a fault at the Brake (Purple wire is active) or the Hood is OPEN (Gray wire grounded). This is a safety
feature of the unit. Check installation for faults and make sure hood is closed and latched and brake wire is not active.
UNIT CRANKS VEHICLE BUT ENGINE NEVER STARTS: (2 parts)
1. In some vehicles, there may be a Factory anti-theft system that will not allow the engine to run without the key in the
ignition. These systems may include Factory Security Modules, GM Passkey®/Passlock®, and RF Transponder
systems (Ford P.A.T.S.®). Many late 1990’s through 2005 vehicles include some type of Anti-Theft system which
may require a bypass module.
2. The vehicle may have more than one Ignition/or Accessory circuit that requires power for the vehicle to start. This is
common on some GM/Toyota vehicles.
VEHICLE STARTS BUT CHECK ENGINE LIGHT COMES ON OR ENGINE RUNS BADLY: (2 parts)
1. Many 1995-UP General Motors cars/trucks require a secondary ignition circuit for the Transmission computer and
other on board systems. If the vehicle is started without this wire energized, there may be a “Check Engine” or
“Service Engine” light on the dash. This may cause damage if the vehicle is driven in this condition. Be sure to check
for an additional WHITE (or sometimes GREEN) Ignition wire on GM cars and trucks. Connect the Pink/White IGN#2
wire to this circuit in the vehicle.
2. Some Vehicles (Commonly Nissan) require 2 Start (Cranking) circuits for the vehicle to run properly. If this is the
case, then use the PINK/WHITE output of this system to power the Starter #2 circuit of the vehicle. See Jumper pin
diagram for configuration. Note that the secondary starter wire may be a smaller gauge wire than the primary starter
wire.
NO RESPONSE FROM REMOTE TRANSMITTER:
1. Check antenna connection: Antenna must be plugged in (3 pin black plug on side of module).
2. Repress remote control Lock or Unlock button several times in succession.
3. Verify if remotes are programmed to module; otherwise perform transmitter learning steps on page 22.
24
JUMPER PIN DIAGRAMS
Jumper pins are used to change/configure the operation of the on board multi-function output PINK/WHITE wire and the Parking
Light WHITE wire. See the diagrams below for Jumper Pin configurations.
CONTROL MODULE
ACC 2
IGN 2 (DEFAULT)
STARTER 2
(-) NEGATIVE PARKING LIGHT (500 mA)
+12V (10A) PARKING LIGHT (DEFAULT)
JUMPER
PLUG
JP1 JUMPERS:
IGN2 / ACC2 / STR2
PINK WHITE
SIDE VIEW
JP2 JUMPERS:
PARKING LIGHT
OUTPUT
25
JUMPER
PINS
ANTENNA DIAGRAM
26
ANTENNA
LOCATIONS
WINDSHIELD
Transceiver Box & Antenna
White Plug
Data port
Data port
Data port
Blue Plug
Color of plug and
EZ-31/3/4DP
EZ-64TW1
EZ-74TW2
EZ-84FM
receptacle must
match!!
Black Plug
Black Plug
27
TRANSMISSION
ECU
ENGINE
ECU
FUEL
PUMP
NOTE: USE EXTERNAL RELAYS FOR HIGH-CURRENT
(GREATER THAN 30A) IGNITION CIRCUITS.
A/C - HEAT
CONTROL
ACC
IGN
STARTER
START #2
JUMPER
SELECT
(See page 23)
IGN #2 or
ACC #2 or
STR #2
(Only if necessary)
STARTER
+/- PARKING
LIGHT
JUMPER
BROWN
GRAY
RED
RED
PINK
PINK/WHITE
PARKING
LIGHTS
WHITE
+10A or -.5A OUTPUT
YELLOW/WHITE
(-) HORN CHIRP / HONK
BLACK
FACTORY
HORN
GROUND
(-) IGNITION
or ANTI-GRIND
RELAY OUTPUT
YELLOW/BLACK
(-) AUX. (TRUNK POP)
or DOME LIGHT
BROWN
DATA PORT
ANTENNA/RECEIVER PLUG
(-) NEGATIVE ENGINE
START / STOP or
TURBO TIMER INPUT
GREEN
(-) START ACTIVATION
(OPTIONAL)
GRAY
DIESEL WAIT
TO START LAMP
(-)HOOD SWITCH
LED
PINK
( -)GLOW PLUG INPUT
WAIT
PURPLE
(+12V) BRAKE PEDAL RESET
PROGRAM
SWITCH
(-) UNLOCK OUTPUT
+12 V FOR RELAYS
(-) LOCK OUTPUT
ORANGE/BLACK: (-)OEM DISARM
BLUE
ORANGE: (-)OEM REARM
RED
3
RED/WHITE
TACH INPUT
8
28
0
TACH
4 5 6
7
2
1
GREEN
-
VEHICLE
BATTERY
FUSE
30A
FUSE
10A
EZ-30/1/3/4DP
EZ-64TW1
EZ-74TW2
+
30A
FUSE
DATA PORT DIAGRAM
This unit includes DP Technology it will allow you to plug our bypass modules model OFA-10/20/30 directly into the unit by via
Data Port. The OFA module cable plugs directly to the Data port on the side of the unit. Please refer to OFA module manual
for detail instructions.
Vehicle
ign with
Anti-theft
NOTE: Most Vehicles 1998 and up
have a Anti- theft system on it.
Please check Tech Notes on vehicle
before installtion.
OFA
Bypass
Module
iDATA LINK CABLE
Module Not Included
Data Port
Antenna
www.crimestopper.com
[email protected]
Phone (800) 998-6880
FAX (805) 581-9500
© 2005Crimestopper Security Products
ONLINE TECHNICAL SUPPORT
www.crimestopper.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement