Weber | Summit 425 LP | Owner`s manual | Weber Summit 425 LP Owner`s manual

Weber Summit 425 LP Owner`s manual
SUMMIT 425 & 450
TM
LP Gas Barbecues
Operating Guide
Read before assembly
Summit 425 LP
Summit 450 LP
Serial Number
Serial Number
WARNING: Follow all leak check procedures
carefully in this manual prior to barbecue
operation. Do this even if barbecue was
dealer assembled.
NOTICE TO INSTALLER: These instructions
must be left with the owner and the owner
should keep them for future use.
THIS GAS APPLIANCE IS DESIGNED FOR
OUTDOOR USE ONLY.
WARNING: Do not try to light this appliance
without reading "Lighting" instructions
section of this manual.
FOR YOUR SAFETY
1. Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.
2. An LP tank not connected for use shall
not be stored in the vicinity of this or
any other appliance.
FOR YOUR SAFETY
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. Open lid.
4. If odor continues, immediately call your
gas supplier or your fire department.
97672
4/97
WARNINGS
DANGER
Failure to follow the Dangers,Warnings and Cautions contained in this Owner’s Manual may
result in serious bodily injury or death, or a fire or an explosion causing damage to property.
■
Do not store a spare or disconnected LP tank under or
near this barbecue.
■
Should a grease fire occur, turn off all burners and
leave lid closed until fire is out.
■
Improper assembly may be dangerous. Please carefully
follow the assembly instructions in this manual.
■
Do not enlarge valve orifices or burner ports when
cleaning the valves or burners.
■
After a period of storage, and/or nonuse, the Weber
Gas Barbecue should be checked for gas leaks and
burner obstructions before using. See instructions in
this manual for correct procedures.
■
The Weber Gas Barbecue should be thoroughly
cleaned on a regular basis.
■
LP gas is not natural gas. The conversion or attempted
use of natural gas in an LP unit or LP gas in a natural
gas unit is dangerous and will void your warranty.
■
Do not attempt to disconnect any gas fitting while your
barbecue is in operation.
■
Use heat-resistant barbecue mitts or gloves when
operating barbecue.
■
This barbecue is for residential use only.
■
Do not operate the Weber Gas Barbecue if there is a
gas leak present.
■
Do not use a flame to check for gas leaks.
■
Combustible materials should never be within
24 inches of the top, bottom, back or sides of your
Weber Gas Barbecue.
■
Do not put a barbecue cover or anything flammable on
or in the storage area under the barbecue.
■
Your Weber Gas Barbecue should never be used
by children.
■
LP GAS UNITS ONLY:
You should exercise reasonable care when operating
your Weber Gas Barbecue. It will be hot during cooking
or cleaning, and should never be left unattended.
■
Use the regulator that is supplied with your Weber
Gas Barbecue.
■
Do not attempt to disconnect the gas regulator or any
gas fitting while your barbecue is in operation.
■
Should the burners go out during operation, turn all gas
valves off. Open the lid and wait five minutes before
attempting to relight, using the lighting instructions.
■
A dented or rusty LP tank may be hazardous and
should be checked by your liquid propane supplier. Do
not use an LP tank with a damaged valve.
■
Do not use charcoal or lava rock in your Weber
Gas Barbecue.
■
■
Never lean over open grill or place hands or fingers on
the front edge of the cooking box.
Although your LP tank may appear to be empty, gas
may still be present, and the tank should be
transported and stored accordingly.
■
If you see, smell or hear the hiss of escaping gas from
the LP tank:
1. Get away from LP tank.
2. Do not attempt to correct the problem yourself.
3. Call your fire department.
2
TABLE OF CONTENTS
Warnings
2
Steam-N-Chips Smoker
Warranty
4
Maintenance
A Word of Thanks
4
Standards and Codes Information
5
Operating Area
Storage
Spider Stopper Guards
Inspection and Cleaning of the
Spider Stopper Guards
Main Burner Flame Pattern
Main Burner Cleaning Procedure
Replacing the Main Burners
Crossover Ignition System Operations
5
5
*REFER TO YOUR STEP-BY-STEP SECTION AT
THIS TIME
Lighting
Crossover Ignition System
To Extinguish
6
Troubleshooting
6
6
Exploded Views and Replacement
Parts Lists
Manual Lighting
7
To Extinguish
7
Cooking
8
Storage
8
Cleaning
8
Summit 425 LP
Summit 450 LP
Patents and Trademarks
3
9
10-12
10
10
11
11
11
13
14
16-19
16-17
18-19
20
WARRANTY
Weber-Stephen Products Co. (Weber) hereby warrants to the ORIGINAL PURCHASER of this Weber Gas Barbecue
that it will be free of defects in material and workmanship from the date of purchase as follows:
Aluminum Castings, 25 years,
Cooking Grates and Flavorizer Bars, 7 years,
All Remaining Parts, 5 years,
when assembled and operated in accordance with the printed instructions accompanying it.
Weber may require reasonable proof of your date of purchase. THEREFORE, YOU SHOULD RETAIN YOUR SALES
SLIP OR INVOICE.
This Limited Warranty shall be limited to the repair or replacement of parts which prove defective under normal use and
service and which on examination shall indicate, to Weber's satisfaction, they are defective. Before returning any parts,
contact Weber-Stephen Products Co. Customer Service Center. If Weber confirms the defect and approves the claim,
Weber will elect to replace such parts without charge. If you are required to return defective parts, transportation charges
must be prepaid. Weber will return parts to the purchaser, freight or postage prepaid.
This Limited Warranty does not cover any failures or operating difficulties due to accident, abuse, misuse, alteration,
misapplication, vandalism, improper installation or improper maintenance or service, or failure to perform normal and
routine maintenance, including but not limited to damage caused by insects within the burner tubes, as set out in this
owner's manual.
Deterioration or damage due to severe weather conditions such as hail, hurricanes, earthquakes or tornadoes, acid rain,
discoloration due to exposure to chemicals either directly or in the atmosphere, is not covered by this Limited Warranty.
There are no other express warrants except as set forth herein and any applicable implied warranties of merchantability
and fitness are limited in duration to the period of coverage of this express written Limited Warranty. Some states do not
allow limitation on how long an implied warranty lasts, so this limitation may not apply to you.
Weber is not liable for any special, indirect or consequential damages. Some states do not allow the exclusion or
limitation of incidental or consequential damages, so this limitation or exclusion may not apply to you.
Weber does not authorize any person or company to assume for it any other obligation or liability in connection with the
sale, installation, use, removal, return, or replacement of its equipment; and no such representations are binding on Weber.
This Warranty applies only to products sold at retail.
A WORD OF THANKS
Thank you for choosing a Weber Barbecue. Our family here at Weber has worked hard to produce the
highest quality products for your satisfaction. While we give much attention to our products, an occasional
error may occur. Our knowledgeable Customer Service staff is prepared to help you with any problems with
parts or assembly. Call our toll free number. For quicker service, please have your owner’s manual and
serial number available for reference. We also welcome any comments or suggestions you might have
regarding our products. We wish you the best in outdoor cooking enjoyment.
Weber-Stephen Products Company
Customer Service Center
200 E. Daniels Road
Palatine, IL 60067-6266
(888) 33-SUMMIT
(888-337-8664)
4
STANDARDS AND CODES INFORMATION
Your Weber Gas Barbecue is a portable outdoor cooking
appliance. With the Weber Gas Barbecue you can grill,
barbecue, roast and bake with results that are difficult to
duplicate with indoor kitchen appliances. The closed lid
and Flavorizer Bars produce that "outdoor" flavor in
the food.
The Weber Gas Barbecue is portable so you can easily
change its location in your yard or on your patio.
Portability means you can take your Weber Gas
Barbecue with you if you move.
Liquid Propane (LP) gas supply is easy to use and gives
you more cooking control than charcoal fuel.
■
The entire cooking box gets hot when in use. Do not
leave unattended.
■
Keep any electrical supply cord and the fuel supply
hose away from any heated surface.
■
Keep the cooking area clear of flammable vapors and
liquids, such as gasoline, alcohol, etc., and
combustible materials.
■
Never store an extra (spare) LP tank under or near
the Weber Gas Barbecue.
Storage
These instructions will give you the minimum
requirements for operating and maintaining your
Weber Gas Barbecue. Please read the instructions
carefully before using your Weber Gas Barbecue.
Improper assembly can be dangerous.
■
The gas must be turned off at the LP tank when the
Weber Gas Barbecue is not in use.
■
When the Weber Gas Barbecue is stored indoors, the
gas supply must be DISCONNECTED and the LP
tank stored outdoors in a well-ventilated space.
■
Not for use by children.
■
■
If there are local codes that apply to portable gas
grills, you will have to conform to them. If there are no
local codes, you must conform to the latest edition of
the National Fuel Gas Code: ANSI Z 223.1.
LP tanks must be stored outdoors in a well-ventilated
area out of reach of children. Disconnected LP tanks
must not be stored in a building, garage or any other
enclosed area.
■
The pressure regulator supplied with the Weber Gas
Barbecue must be used. This regulator is set for 10.5
inches of water column (pressure).
When the LP tank is not disconnected from the
Weber Gas Barbecue, the appliance and LP tank
must be kept outdoors in a well-ventilated space.
■
The Weber Gas Barbecue should be checked for gas
leaks and any obstructions in the burner tubes before
using. (See Maintenance Section)
■
Check that the areas under the control panel and the
bottom tray are free from debris that might obstruct
the flow of combustion or ventilation air.
■
The Spider Stopper Guards should also be checked
for any obstructions. Refer to Maintenance Section.
■
■
■
■
This Weber Gas Barbecue is designed for use with
liquid propane (LP) gas only. Do not use with natural
(piped in city) gas. The valves, orifices, hose and
regulator are for LP gas only.
Do not use with charcoal fuel.
For Installation in Canada
These instructions, while generally acceptable, do not
necessarily comply with the Canadian Installation codes,
particularly with piping above and below ground. In Canada
the installation of this appliance must comply with local
codes and/or Standard CAN/CGA-B149.2 (Installation
Code for Propane Burning Appliances and Equipment).
Operating area
REFER TO YOUR STEP-BYSTEP GUIDE AT THIS TIME
FOR BARBECUE ASSEMBLY
WARNING: Only use this barbecue outdoors in a well
ventilated area. Do not use in a garage, building,
breezeway or any other enclosed area.
WARNING: Make sure your barbecue is set up
properly and leak checked before attempting
to operate.
■
Never use your Weber Gas Barbecue under an
unprotected combustible roof or overhang.
■
Your Weber Gas Barbecue is not intended to be
installed in or on recreational vehicles and/or boats.
■
Keep this grill away from combustible materials when
in use at a minimum of 24 inches of the top, bottom,
back or sides.
5
LIGHTING
EACH HEAT ZONE OPERATES INDEPENDENTLY.
1) Open the lid. Figure 1.
Summary lighting instructions are on the control panel.
2) Check that the fuel scale reads more than “E”.
Note - E = empty; F = full.
3) Make sure all burner control knobs are OFF. (Push
each burner control knob down and turn clockwise.)
High
Medium
Low
WARNING: The b urner control knobs must be in the
OFF position before turning on the LP tank valve. If
they are not in the OFF position, when you turn on
the LP tank valve, the excess flow control will
activate, limiting the flow of gas from the LP tank. If
this should occur, turn OFF the LP tank valve and
burner control knobs and start over.
Off
Crossover Ignition System
DANGER
Failure to open lid while igniting the
barbecue, or not waiting 5 minutes to allow
the gas to clear if the barbecue does not light,
may result in an explosive flame-up which
can cause serious bodily injury or death.
DANGER
When the excess flow control is activated,
a small amount of gas is still flowing to the
burners. After turning OFF the tank and
burner control knobs, wait at least 5 minutes
for the gas to clear before attempting to light
the barbecue. Failure to do so may result in
an explosive flame-up which can cause
serious bodily injury or death.
Note - The Crossover Ignition System ignites the Left
burner of each heat zone with a spark from the igniter
electrode inside the Gas Catcher Ignition Chamber. You
generate the energy for the spark by pushing the
Crossover Ignition Button until it clicks.
4) Turn the tank on by turning the tank valve
counterclockwise.
WARNING: Check hose before each use of barbecue
for nicks, cracking, abrasions or cuts. If the hose is
found to be damaged in any way, do not use the
barbecue. Contact your dealer.
WARNING: Do not lean over open barbecue. Keep
your face and body at least one foot away from the
matchlight hole when lighting the barbecue.
WARNING:The storage space under the cooking
module is intended for storage of nonflammable
items only.
5) Select Heat Zone.
Crossover Ignition System
6) Push LEFT burner control knob down and turn to
START/HI.
7) Push the Crossover Ignition Button several times, so
it clicks each time.
8) Check that the burner is lit by looking through the
matchlight hole above the burner control knob.
WARNING: If the burner does not light, turn the LEFT
burner control knob to OFF and wait 5 minutes to let
the gas clear before you try again or try to light with
a match.
9) After the LEFT burner is lit you can turn on the
RIGHT burner.
Note - Always light the LEFT burner first.The RIGHT
burner ignites from the LEFT burner.
TO EXTINGUISH
Figure 1
Turn gas supply OFF at the source, then push down
and turn each burner control knob clockwise to OFF.
6
MANUAL LIGHTING
EACH HEAT ZONE OPERATES INDEPENDENTLY.
High
Medium
Low
DANGER
When the excess flow control is activated, a
small amount of gas is still flowing to the
burners. After turning OFF the tank and burner
control knobs,wait at least 5 minutes for the gas
to clear before attempting to light the barbecue.
Failure to do so may result in an explosive
flame-up which can cause serious bodily injury
or death.
Off
DANGER
Failure to open lid while igniting the
barbecue, or not waiting 5 minutes to allow
the gas to clear if the barbecue does not light,
may result in an explosive flame-up which
can cause serious bodily injury or death.
4) Turn the tank on by turning the tank valve
counterclockwise.
5) Select heat zone.
6) Put a match in the match holder and strike the match.
1) Open the lid. Figure 2.
7) Insert match holder and lit match through matchlight
hole to ignite LEFT burner. Figure 3.
2) Check that fuel scale reads more than “E”.
Note - E = empty; F = full.
WARNING: Do not lean over open barbecue. Keep
your face and body at least one foot away from the
matchlight hole when lighting the barbecue.
3) Make sure all burner control knobs are turned OFF. (Push
each burner control knob down and turn clockwise.)
WARNING: The b urner control knobs must be in the
OFF position before turning on the LP tank valve. If
they are not in the OFF position, when you turn on
the LP tank valve, the excess flow control will activate,
limiting the flow of gas from the LP tank. If this should
occur, turn OFF the LP tank valve and burner control
knobs and start over.
8) Push LEFT burner control knob down and turn to
H (high).
matchlight hole
in control panel
Hole in cooking
box assembly
WARNING:The storage space under the cooking
module is intended for storage of nonflammable
items only.
Manual Lighting
Control panel
Left burner
tube
Figure 3
9) Observe if LEFT burner has ignited by looking
through matchlight hole.
WARNING: If LEFT burner fails to ignite turn LEFT
burner control knob to OFF and wait 5 minutes before
attempting to ignite again.
10) After the LEFT burner is lit you can turn on the
RIGHT burner.
Note: Always light the LEFT burner first.The RIGHT
burner ignites from the LEFT burner.
TO EXTINGUISH
Turn gas supply OFF at the source, then push down
and turn each burner control knob clockwise to OFF.
Figure 2
7
COOKING
CLEANING
The Weber Gas Barbecue should not be moved when
operating or hot.
CAUTION: Turn your Weber Gas Barbecue OFF and
wait for it to cool before cleaning.
High
Medium
Low
CAUTION: Do not clean your Flavorizer Bars or
cooking grills in a self-cleaning oven. Replacement
cooking grates and Flavorizer Bars are available
through your retailer or the Weber-Stephen Customer
Service Center.
Off
You can adjust the LEFT and RIGHT burners as desired.
The control settings High (H), Medium (M), Low (L), or Off
(O) are described in your Weber cookbook. The cookbook
uses these notations to describe the settings of the LEFT
and RIGHT burners.
Outside surfaces - Use a warm soapy water solution.
CAUTION: Do not use oven cleaner, abrasive cleansers
(kitchen cleansers) cleaners that contain citrus
products or abrasive cleaning pads on barbecue or
cart surfaces.
Note: Cooking conditions may require the adjustment of
the burner controls.
Bottom tray - Remove excess grease and then wash with
warm soapy water.
If burners go out during cooking, turn off all burners
and wait 5 minutes before relighting.
Flavorizer Bars and Cooking Grates - Clean with a
suitable brass bristle brush. As needed, remove from grill
and wash with warm soapy water.
CAUTION: Check the bottom tray for grease build-up
before each use. Remove excess grease to avoid a
grease fire in the bottom tray.
Catch pan - Disposable foil trays are available, or you
can line the catch pan with aluminum foil. To clean the
catch pan, wash with warm soapy water.
STORAGE
■
The gas must be turned off at the LP cylinder when
the Weber Gas Barbecue is not in use.
■
When the Weber Gas Barbecue is stored indoors, the
gas supply must be DISCONNECTED and the LP
cylinder stored outdoors in a well-ventilated space.
■
LP cylinders must be stored outdoors in a wellventilated area out of reach of children. Disconnected
LP cylinders must not be stored in a building, garage
or any other enclosed area.
■
When the LP cylinder is not disconnected from the
Weber Gas Barbecue, the appliance and LP cylinder
must be kept outdoors in a well-ventilated space.
■
The Weber Gas Barbecue should be checked for gas
leaks and any obstructions in the burner tubes before
using. (See Maintenance Section.)
■
Check that the areas under the control panel and the
bottom tray are free from debris that might obstruct
the flow of combustion or ventilation air.
Thermometer - Wipe with warm soapy water, clean with
plastic scrub ball. Do not put in dishwasher or submerge
in water.
Inside cooking module - Brush any debris off of burners
tubes. DO NOT ENLARGE BURNER PORTS (OPENINGS).
Wash inside of cooking box with warm soapy water.
Inside lid - While lid is warm, wipe inside with paper
towel to prevent flaking due to grease build-up.
Stainless steel surfaces - Wash with a soft cloth and
soap and water solution.
8
USING THE STEAM-N-CHIPS SMOKER
The Steam-N-Chips Smoker cooks with both Weber
FireSpice Wood Chips and Chunks. For best results with
faster cooking foods like steaks, burgers and chops, etc.,
we recommend using the FireSpice Chips because they
ignite and create smoke faster. For longer cooking foods
such as roasts, chicken and turkeys, etc., we recommend
using FireSpice Chunks because they ignite slowly and
provide smoke for a longer period of time. As you gain
experience in using your Steam-N-Chips Smoker, we
encourage you to experiment with different combinations of
FireSpice Chips and Chunks to find the smoke flavor that
best suits your taste.
DANGER
Do not use any flammable fluid in the
Steam-N-Chips Smoker to ignite the wood.
This will cause serious bodily injury.
Cleaning the Steam-N-Chips Smoker
Before each use, empty the Steam-N-Chips Smoker of
ash to allow proper air flow.
Note - Smoking will leave a "smoke" residue on the
surface of the smoker. This residue cannot be removed
and will not affect the function of the Steam-N-Chips
Smoker. To a lesser degree a "smoke" residue will
accumulate on the inside of your Weber Gas Barbecue.
This residue need not be removed and will not adversely
affect the function of your Weber Gas Barbecue.
To use the Steam-N-Chips Smoker
As a starting point, place a handful of FireSpice Chips or a
few FireSpice Chunks in the bottom of the smoker body.
Figure 4. Since the chunks vary in size, place as many as
you can in the smoker allowing room for the water pan. As
you gain experience in smoking, increase or decrease the
amount of wood to suit your taste. Fill water pan, place it in
the smoker and close the smoker lid.
Water Pan
Steam-N-Chips Body
Place wood in here
Figure 4
Light the barbecue and preheat with all burners on HIGH,
lid down, for 10 minutes or until the thermometer registers
500°F - 550°F. Adjust the burners for cooking; MM or LL
will be your best settings for long duration smoking. Smoke
will start in approximately 10 minutes and last as long as
45 minutes. If you require more smoke flavor, refill the
smoker with FireSpice Chips and/or Chunks and refill the
water pan with water. The Steam-N-Chips Smoker may be
used to enhance any of the meat, poultry and fish recipes
in the gas barbecue cookbook. Cook with the lid down
according to the times indicated in charts or recipes.
Note - After refilling smoker, smoke will take about 10 to
15 minutes to start again.
9
MAINTENANCE
Spider Stopper Guards
We recommend that you inspect the Spider Stopper
Guards at least once a year. Also inspect and clean the
Spider Stopper Guards if any of the following
symptoms should ever occur.
Your Gas Barbecue, as well as any outdoor gas
appliance, is a target for spiders and other insects. They
can nest in the venturi section of the burner tubes. This
blocks the normal gas flow, and can cause the gas to
flow back out of the air shutter. Figure 5. This could result
in a fire in and around the air shutters, under the control
panel, causing serious damage to your barbecue.
1. The smell of gas in conjunction with the burner
flames appearing yellow and lazy.
2. Barbecue does not reach temperature.
Venturi
3. Barbecue heats unevenly.
4. One or more of the burners do not ignite.
DANGER
Air shutter
Failure to correct these symptoms may
result in a fire which can cause serious bodily
injury or death and cause damage to property.
Venturi fin
Figure 5
Inspection and Cleaning of the Spider
Stopper Guards
The Spider Stopper Guard is factory installed. It fits
tightly around the air shutter section of the burner tube
and the valve, thereby preventing spiders and other
insects access to the burner tubes through the air
shutter openings. Figure 6.
To inspect the Spider Stopper Guards, remove the control
panel and look to see if they have dust or dirt on their
outside surfaces. If they are dirty, brush off the outside
surface of the Spider Stopper Guards with a soft bristle
brush (an old toothbrush for example). Check that there
are no gaps in the Spider Stopper Guards’ seams or in
the fit around the burners or valves.
Weber Spider
Stopper Guard
Figure 6
10
MAINTENANCE
Main Burner Flame Pattern
Replacing Main Burners
The Weber Gas Barbecue burners have been factory set
for the correct air and gas mixture. The correct flame
pattern is shown in Figure 7.
1.
2.
3.
4.
Burner inside
cooking box
Your Weber Gas Barbecue must be OFF and cool.
Turn OFF gas at source.
Disconnect regulator.
To remove control panel refer to “Remove the control
panel and the front panel” in the Step-By-Step Guide.
5. Remove cooking grates.
6. Remove Flavorizer bars.
7. Remove the manifold by unsnapping the clips at the
right and left front of the cooking box. Figure 10.
Tips occasionally yellowish
Light blue
Dark blue
Flames
Figure 7
If the flames do not appear to be uniform the length of the
burner tube, follow the burner cleaning procedures.
Main Burner Cleaning Procedure
Turn off the gas supply. Remove the manifold.
Look inside each burner with a flashlight. Figure 8.
Figure 8
Clean the inside of the burners with a wire (a straightened
out coat hanger will work). Figure 9. Check and clean the
air shutter opening at the ends of the burners. Check and
clean the valve orifices at the base of the valves. Use a
brass bristle brush to clean outside of burners. This is to
make sure all the burner ports are fully open.
Figure 10
8. Disconnect white and black wire from each igniter.
Figure 11.
Figure 9
White wire
CAUTION: Do not enlarge the burner ports when cleaning.
Black wire
Figure 11
11
MAINTENANCE
9. Unlatch the Spider Stopper Guards and remove.
Figure 12.
11. Slide the burner assembly from each Heat Zone. The
left and right burners are connected by the Crossover
tube. Figure 14 (a).
Pull out of here
Crossover tube
Figure 12
10. Pull the manifold out of the burners. Figure 13.
Manifold
Figure 14
Figure 13
12
MAINTENANCE
12. Lift and twist the burner assembly slightly to separate
the crossover tube from the burners. Remove the
burners from the cooking box. Figure 15.
14. Reinstall the Spider Stopper Guards. Slightly rotate
the Spider Stopper Guards so that the seams are in
line with the Venturi fins. There should be no gaps in
the seams or in the fit around the burners and valves.
Figure 17.
Separate here
Check fit
around valve
Crossover tube
Venturi fin
Figure 15
Check fit around burner
13. To reinstall the burners, reverse steps 3 through 12.
Figure 17
CAUTION: The burner openings must be positioned
properly over the valve orifices. Figure 16 (a).
Check proper assembly before fastening manifold in
place. Figure 16 (b).
Crossover Ignition System Operations
If the Crossover Ignition System fails to ignite the Left
burner, light the Left burner with a match. If the Left
burner lights with a match, then check the Crossover
Ignition System.
(a)
Valve
■
Check that both the white and black ignition wires are
attached properly. Figure 18.
■
Check that the Crossover Ignition button pushes the
igniter (button) down, and returns to the up position.
■
Check to see if the igniter is loose in the frame.
Tighten if necessary; See Step “Install igniter” for
correct procedure.
Burner
Orifice
(b)
If the Crossover Ignition System still fails to light, contact
Weber-Stephen Customer Service.
White wire
Black wire
Figure 16
Figure 18
13
TROUBLESHOOTING
Problem
Cure
Check
Burners burn with a yellow or orange flame, Inspect Spider Stopper Guards for
in conjunction with the smell of gas.
possible obstructions. (Blockage
of holes.)
Clean Spider Stopper Guards. (See
Maintenance Section.)
Burners do not light. -orBurners have a small flickering flame in
the HIGH position. -orBarbecue temperature only reaches 250˚
to 300˚ degrees in the HIGH position.
The excess flow safety device,
which is part of the barbecue to
tank connection, may have
activated.
To reset the excess flow safety
device turn all burner control knobs
and the tank valve OFF. Disconnect
the regulator from the tank. Turn
burner control knobs to HIGH. Wait
at least 1 minute. Turn burner
control knobs OFF. Reconnect the
regulator to the tank. Turn tank
valve on slowly. Refer to Lighting
Section.
Burner does not light, or flame is low in
HIGH position.
Is LP fuel low or empty?
Refill LP tank.
Is fuel hose bent or kinked?
Straighten fuel hose.
Does the Left burner light with a
match?
If you can light the Left burner with
a match, then check the Crossover
Ignition System.
Experiencing flare-ups:
Are you preheating barbecue in the All burners on high for 10 to 15
minutes for preheating.
prescribed manner?
Are the cooking grates and
Flavorizer Bars heavily coated with
burned-on grease?
CAUTION: Do not line the bottom tray
with aluminum foil.
Clean thoroughly. (See Cleaning
Section.)
Clean bottom tray.
Is the bottom tray "dirty" and not
allowing grease to flow into catch pan?
Burner flame pattern is erratic. Flame is
Are burners clean?
low when burner is on HIGH. Flames do
not run the whole length of the burner tube.
Clean burners. (See Maintenance
Section.)
Fuel scale shows that there is gas in the
LP tank, but tank is empty.
Fuel scale must be adjusted with
an empty tank.
Check adjustment of fuel scale.
If problems cannot be corrected by using these methods, please contact
Weber-Stephen Customer Service.
14
15
EXPLODED VIEW FOR THE SUMMIT 425 LP
16
REPLACEMENT PARTS LIST FOR THE SUMMIT 425 LP
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
Lid
Thermometer
Steam-N-Chips smoker
Stainless steel work surface (2)
Condiment holder (2)
Cooking box
Crossover tube (2)
Left burner (2)
Right burner (2)
Burner control knobs (4)
Igniter (2)
Igniter lock nut (2)
Igniter wire (white) (2)
Igniter wire (black) (2)
Gas catcher ignition chamber (2)
Spider stopper guard (4)
Manifold assembly
Manifold mounting clips (2)
Control panel
Igniter button (2)
Front panel
Tool holder (4)
Caster frame
1/4-20 x 3 1/2 inch bolt (4)
Match holder and chain
Bottom tray
Catch pan holder
Catch pan
Drip pan (2)
Caster (2)
Bottom connector (2)
Stainless steel bottom shelf
Warm-up rack
Cooking grates (2)
Flavorizer bar / cooking grate holder (2)
Flavorizer bar (7)
Hair pin cotter (2)
Clevis pin (2)
Corrugated gas line
Hose adapter
Top left frame
Top right frame
Back panel
Nylon washer (8)
1/4-20 x 1/2 inch bolt (4)
Wheel frame
1/4-20 wing nuts (2)
Wheel hubcap (2)
Wheel (2)
Cylinder glides (2)
Glide axle
Glide hubcaps (2)
Cylinder panel
Fuel scale assembly
55
56
57
58
59
60
1/4-20 x 1 3/4 inch bolt
1/4-20 hex nut
Regulator mounting bracket
Hose / regulator
LP tank
Filler adapter
All items are single quantities unless otherwise specified.
Parts can be ordered directly from Weber-Stephen
Products Company by phone or mail.
Note - Do not return parts to Weber-Stephen Products Co.
without first contacting the Customer Service Center by
phone or mail. Returning the part may not be necessary.
While we give much attention to our products,
unfortunately an occasional error may occur. If a part is
missing, do not go back to the store. Call the Weber
Customer Service Center toll free 1-888-33-SUMMIT
(1-888-337-8664) to receive immediate assistance. Have
your owner’s manual and serial number of the barbecue
available for reference.
Weber-Stephen Products Company
Customer Service Center
250 South Hicks Road
Palatine, IL 60067-6241
(888) 33-SUMMIT
(888-337-8664)
WARNING:
Use only Weber factory authorized parts.The
use of any part that is not factory authorized can
be dangerous. This will also void your warranty.
17
EXPLODED VIEW FOR THE SUMMIT 450 LP
18
REPLACEMENT PARTS LIST FOR THE SUMMIT 450 LP
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
Lid
Thermometer
Cooking grate (2)
Flavorizer bar / cooking grate (2)
Flavorizer bar (7)
Stainless steel work surface (2)
Condiment holder (2)
Cooking box
Crossover tube (2)
Left burner (2)
Right burner (2)
Burner control knob (4)
Igniter (2)
Igniter lock nut (2)
Igniter wire (black) (2)
Igniter wire (white) (2)
Gas catcher ignition chamber (2)
Spider stopper guard (4)
Manifold assembly
Manifold mounting clips (2)
Control panel
Igniter button (2)
Front panel
Rear panel (2)
Left panel
Match holder and chain
Caster frame
1/4-20 x 3 1/2 inch bolt (4)
Bottom connector (3)
Tool holder (4)
Caster (2)
Bottom tray
Catch pan holder
Catch pan
Drip pan (2)
Left front door
Right front door
Accessory rack
Warm-up basket
Steam-N-Chips smoker
Hair pin cotter (2)
Clevis pin (2)
Regulator mounting bracket
Corrugated gas line
Hose adapter
Top left frame
Top right frame
Back panel
Nylon washer (8)
1/4-20 x 1/2 inch bolt (4)
1/4-20 wing nut
Wheel hubcap (2)
Wheel (2)
Cylinder glide (2)
Glide axle
Glide hubcap (2)
Cylinder panel
58
59
60
61
62
63
64
65
Right panel
Tank scale assembly
1/4-20 x 1 3/4 inch bolt
1/4-20 keps nut
Hose / regulator
LP tank
Filler adapter
Wheel frame
All items are single quantities unless otherwise specified.
Parts can be ordered directly from Weber-Stephen
Products Company by phone or mail.
Note - Do not return parts to Weber-Stephen Products Co.
without first contacting the Customer Service Center by
phone or mail. Returning the part may not be necessary.
While we give much attention to our products,
unfortunately an occasional error may occur. If a part is
missing, do not go back to the store. Call the Weber
Customer Service Center toll free 1-888-33-SUMMIT
(1-888-337-8664) to receive immediate assistance. Have
your owner’s manual and serial number of the barbecue
available for reference.
Weber-Stephen Products Company
Customer Service Center
250 South Hicks Road
Palatine, IL 60067-6241
(888) 33-SUMMIT
(888-337-8664)
WARNING:
Use only Weber factory authorized parts.The
use of any part that is not factory authorized can
be dangerous. This will also void your warranty.
19
PATENTS & TRADEMARKS
© 1997 Weber-Stephen Products Co. Weber, the silhouette, Flavorizer and Crossover are registered
U.S. trademarks; Summit, Grill Cozy, Gas Catcher, Spider Stopper, and Steam-N-Chips, are
trademarks, all of Weber-Stephen Products Co., 200 East Daniels Road, Palatine, IL 60067-6266.
U.S.A.
Summit Series Gas Barbecues are covered by U.S. Patent Nos. 4,677,964; 4,727,853; 4,777,927;
4,829,978; 4,860,724; 4,941,817; and 4,966,125; and, Canada patent Nos. 1,283,586 and 1,300,995.
Printed in the U.S.A.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising