- No category
advertisement
WPP-531-D OR SSP-511-D-SPK1.07UNVLr1-ADA-ISSUE4.0
SERVICE MANUAL
FOR
MODEL WPP-531-D
WEATHERPROOF TELEPHONE
WITH OPTIONAL ADA FEATURE
OR
MODEL SSP-511-D
STAINLESS STEEL PANEL TELEPHONE
WITH OPTIONAL ADA FEATURE
EQUIPPED WITH SPK1.07UNVLr1 FIRMWARE
Serving the Telephone Industry Since 1930
519 W South Park Street
Okeechobee, FL 34972
863-357-0798
863-357-0006
Issue 4.0
IMPORTANT INFORMATION
FOR
CUSTOMER
Please fill in before you continue.
The following information is necessary when calling CEECO for assistance.
MODEL NUMBER MODEL WPP-531-D OR SSP-511-D
EQUIPPED WITH SPK1.07UNVLr1
FIRMWARE AND OPTIONAL ADA
FEATURE
SERIAL NUMBER
DATE MANUFACTURED
LOCATION INSTALLED
For us to better serve you, please have this information available when calling for technical support.
CEECO
Communication Equipment & Engineering Company
519 W South Park Street
Okeechobee, FL 34972
863-357-0798- telephone
863-357-0006- facsimile [email protected]
www.ceeco.net
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
2
Issue 4.0
TABLE OF CONTENTS
SECTION PAGE
1.0
INTRODUCTION
............................................................................................................. 4
2.0
GENERAL
.............................................................................................................................. 4
3.0
PROGRAMMING
............................................................................................................ 5
PROGRAMMING CONTINUED…
.................................................................... 6
PROGRAMMING CONTINUED…
.................................................................... 7
4.0
OPERATION
........................................................................................................................ 7
5.0
RECOMMENDED TOOLS AND TEST EQUIPMENT
...................... 8
6.0
INSTALLATION NOTES AND ASSEMBLY INSTRUCTIONS
.. 8
7.0
OVER-VOLTAGE PROTECTION DIAGRAM
........................................ 9
8.0
TESTING
................................................................................................................................. 9
9.0
SPECIFICATIONS
........................................................................................................ 10
10.0
PARTS LIST
....................................................................................................................... 11
11.0 FCC NOTICE
.................................................................................................................... 12
12.0
REPAIR AND RETURN INFORMATION
................................................. 13
13.0
WARRANTY POLICY
............................................................................................... 14
14.0
DIAGRAM
............................................................................................................................ 15
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
3
Issue 4.0
1.0 INTRODUCTION
The practices in this manual provide installation and maintenance information for
Model WPP-531-D or Model SSP-511-D Telephone with optional ADA feature, equipped with SPK1.07UNVLr1 firmware.
The information in this manual is subject to change without notification.
For information not included in this manual, please call or write:
CEECO
Customer Service
519 W South Park Street
Okeechobee, FL 34972
863-357-0798- telephone
863-357-0006- facsimile [email protected]
www.ceeco.net
2.0 GENERAL
2.1
The CEECO hands free telephone is a sturdy, vandal resistant, stainless steel speakerphone with an optional ADA feature (red/green LED for visual call progress indication). Instead of a hookswitch and handset, the telephone has a press to start/press to stop button for the initiation and termination of phone calls. Manual volume control is also provided inside the telephone on the PC board.
2.2
The microphone is muted during periods of dial tone to deter the use of hand held dialers to make fraudulent calls.
2.3
Incoming calls may be allowed or blocked depending on the programming.
2.3
Programming is accomplished by way of a DTMF keypad, which is provided separately.
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
4
Issue 4.0
3.0 PROGRAMMING
NOTE: It is recommended that you ground yourself to prevent ESD damage to the PCB(s).
3.1
Connect the telephone to a working telephone line or a DTMF test set.
3.2
Locate the pair of plastic mini-jumpers along the edge of the PC board.
Move them to the “on” or inner most position as depicted in the diagram on the last page of this manual.
3.3 Press the “CALL & HANGUP” button and wait for dial tone before entering programming digits.
3.4
Begin by entering #97#18#, which will clear all user programmable
memory.
NOTE: Once the # key has been entered, you may hear a fast busy tone, an operator recording, or other Central Office signals. Please disregard these sounds and continue programming, as they will have no effect on the programming.
3.5
Each programming location is accessed by dialing the # sign and the corresponding two digit code. The previous contents of the location are automatically erased when the location code is accessed.
3.6
Location “00” is the telephone options location. Please review the options on the next page. By entering a selected number of 0-9 into each of the ten digits, the phone is customized for the particular installation. Enter
#00, followed by a series of ten digits, as selected from the next page.
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
5
PROGRAMMING CONTINUED…
1
#00:
Digit
0 Always 0 for this model.
Digit 2
0 No incoming calls allowed.
1
Digit 3
Incoming calls allowed.
0 No conversation time-out.
1-9 Minute(s) conversation time-out.
Digit 4
0
Digit 5
Always 0 for this model.
0 Always 0 for this model.
Digit 6
0 Deactivate ADA feature (red/green LED).
9
Digit 7
Activate ADA feature (red/green LED).
0
Digit 8
Always 0 for this model.
0 Do not dial PBX access number stored in location #18.
1
Digit 9
Dial PBX number stored in location #18.
0 Always 0 for this model
Digit 10
0 No wink detect.
1-9 Length of the wink detect.
(1=50ms incremental to 450 ms. 5 is recommended).
• Be sure to log your entries here for future reference:
(OPTION TABLE) #00 0 _ _ 0 0 _ 0 _ 0 _
1 2 3 4 5 6 7 8 9 10
EXAMPLE: Dial #00 0160000005
Phone will be set as follows:
Digit 1- Always 0.
Digit 2- Incoming calls allowed.
Digit 3- 6 minute conversation time out.
Digit 4- Always 0.
Digit 5- Always 0.
Digit 6- ADA deactivated.
Digit 7- Always 0.
Digit 8- Do not dial PBX access number.
Digit 9- Always 0.
Digit 10- 250 ms wink detect.
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
Issue 4.0
6
Issue 4.0
PROGRAMMING CONTINUED…
3.7
If it is necessary for the telephone to automatically dial (Auto Dial) a
number when the “CALL & HANGUP” button is pressed, enter #19,
followed by the desired number. The number may range from 1-11 digits. The time-out disconnect feature (if programmed) will start after this number has been dialed. If this is not a desired function, please proceed to the next section.
EXAMPLE: Enter #19 5551212. This will cause the phone to automatically dial the seven-digit number, 5551212, when the “CALL &
HANGUP” button is pressed.
3.8
If it is necessary for the telephone to automatically dial a PBX or other
access number, enter #18, followed by the desired number. The number may range from 1-11 digits. Provided that a 1 was entered under
Digit 8 in LOCATION #00, the number stored in location #18 will automatically dial first, followed by a 1 second pause, and then the number stored in location #19 will automatically dial. If this is not a desired function, please proceed to the next section.
EXAMPLE: Enter #18 18001234567. This will cause the phone to automatically dial the eleven digit 1800 number, followed by a 1 second pause, followed by the automatic dialing of the number stored in location
#19.
3.9
When programming is finished, press the “CALL & HANGUP” button to
hang up the phone. Return the two mini-jumpers to the “off” or outermost position, as depicted on the last page of this manual. Secure the telephone to its mounting. The phone is now ready for use.
4.0 OPERATION
To make a call, press the “CALL & HANGUP” button located on the front of the telephone and wait to hear dial tone. The LED will illuminate red at this time and the programmed auto-dial numbers will dial out on the line. The LED will flash red and green while the call is ringing. When the called party answers, the LED will turn GREEN after a maximum of four seconds (assuming the ADA feature is activated). When the call is complete, press the “CALL & HANGUP” button to hang up the phone. The call will be terminated and the LED will go out.
NOTE: If the telephone is being used to make emergency calls, CEECO cannot assume responsibility for the called party’s response.
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
7
Issue 4.0
5.0 RECOMMENDED TOOLS AND TEST EQUIPMENT
DTMF Test Set
Volt/Ohm Meter
3/8” Nut Driver
5/16” Nut Driver
Flat Blade Screw Driver
Security Tool 301-064
6.0 INSTALLATION NOTES AND ASSEMBLY INSTRUCTIONS
6.1
Using a 301-064 security tool (sold separately) remove the four security screws.
6.3 Run the inside station wire through the housing or enclosure and terminate the wire on the RJ11C modular jack, as depicted on the following page.
The CEECO provided modular jack must be used, as it contains required over-voltage protection.
6.4 The use of a gas tube or carbon station protectors is recommended. The
station ground should not exceed 50 ohms.
6.5 Plug the modular line cord from the PC board into the RJ11C terminal block.
6.6 Dress the line cord away from the security screws and seat the phone into the housing or enclosure.
6.7 Secure the telephone assembly by replacing and tightening the four
security screws.
*****WARNING*****
A. Never install telephone wiring during a lightning storm.
B. Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.
C. Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.
D. Use caution when installing or modifying telephone lines.
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
8
Issue 4.0
8.0 TESTING
Press the “CALL & HANGUP” button.
Reaction: Dial tone is heard and red LED illuminates.
Programmed number(s) automatically dials out.
Action:
LED flashes red and green while ringing (optional ADA feature).
The called party answers.
Reaction: A normal speakerphone conversation is allowed.
The LED illuminates green (optional ADA feature) after a maximum of 4 seconds.
Press the “CALL & HANGUP” button to hang up the phone.
Reaction: The LED goes out.
The terminated.
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
9
9.0 SPECIFICATIONS
Input Power:
Loop Current:
Impedance:
Signaling:
C.O. Line Powered (48-52 Volt Loop)
30 mA min. 80 mA max.
DTMF, 70 ms tone, 50 ms spacing.
Humidity
Programming:
(SSP)
Weight: Approximately
Weatherproof
Housing:
(WPP)
Mounting: 4 holes spaced 8" x 5 7/8" x 13/32" pounds
Memory retention:
UL listed no.:
Non-volatile memory retention
60F5
FCC registration:
Ringer equivalence:
Type
BW8USA-73021-MT-E
0.4a
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
Issue 4.0
10
Issue 4.0
QUANTITY PART NUMBER DESCRIPTION
4 331-006 Outer screw.
1 301-054-UL
1 660-000 CEECO
1 705-110 Connectorized
Momentary Switch.
1 14123
1 331-005 Weatherproof
500-091 Stainless Steel Panel. 1
OPTIONS
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
11
Issue 4.0
11.0 FCC NOTICE
11.1 FCC REGISTRATION AND REPAIR INFORMATION
Your new telephone has been registered with the Federal Communication
Commission (FCC) in accordance with Part 68 of its rules. The FCC requires that you be advised of certain requirements involving the use of this telephone.
11.2 CONNECTION WITH THE NATIONWIDE TELEPHONE
NETWORK
The FCC requires that you connect this telephone to the Nationwide
Telephone Network through a registered jack provided by the telephone company in your area. This jack is a modular outlet, which you can order from your local telephone company.
11.3 NOTIFICATION TO THE TELEPHONE COMPANY
Before connecting this telephone, the FCC requires that you notify your local telephone company business office. The number is in the front of your phone book.
Tell them: The "line" to which you will connect the telephone (that is, your phone number) and the telephone's FCC registration number and ringer equivalence number. These numbers are listed in section 9.0.
The FCC further requires that you notify your local telephone company when permanently disconnecting this telephone.
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
12
Issue 4.0
12.0 REPAIR AND RETURN INFORMATION
12.1 WARRANTY REPAIR
Any device returned requiring warranty service; repair or credit must be accompanied with a "Return Material Authorization" (RMA) FORM. It must include return shipping instructions, original purchase order number and special marking instruction. A description of the trouble observed must be attached to the defective unit. This information must be inside the shipping container.
12.2 DIRECT ALL INQUIRES TO:
CEECO
Repair Department
863-357-0798- telephone
863-357-0006- facsimile [email protected]
www.ceeco.net
12.3 NON-WARRANTY REPAIR
CEECO will repair equipment out of warranty for a set charge plus parts.
The customer must pay the shipping costs both directions.
12.4 RETURN FOR CREDIT
Material may be returned for credit only with prior approval. Material authorized for return is subject to a 20% restocking charge based on the manufacturer’s list price. Return RMA must be requested no later than 30 days after original shipment.
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
13
Issue 4.0
13.0 WARRANTY
13.1 GENERAL
CEECO products are guaranteed to be free of defects in material and workmanship for a period of 12 months from the date of original shipment, if properly installed and maintained. This warranty is limited to the value of material only.
CEECO will repair or replace any unit during this period if found to be defective for reasons other than abuse and improper use or improper installation. It is the buyer’s responsibility to return the defective unit to the factory. CEECO will then repair or replace any defective parts and return them to the buyer free of charge.
13.2 PRINTED CIRCUIT BOARDS
Printed circuit boards should not be repaired in the field. If a unit is found to be faulty, replace it with another unit and return the faulty unit to CEECO for repair. Modifications by any one other than
CEECO will void the warranty.
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
14
Issue 4.0
14.0 DIAGRAM
Locate the mini jumpers on the corner of the PCB.
ON
OF
F
M
OVE THE MINI JUMPERS
TO THE
ON
POSITION
BEFORE
GOING OFF
-
HOOK
.
ON
OF
F
When programming is completed, move the mini jumpers to the OFF position.
NOTE:
Do not leave the mini jumpers in the ON position; this will decrease battery life.
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
ON
OF
F
15
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project