Yamaha CDX-1060 Owner's manual

Yamaha CDX-1060 Owner's manual
 “Repeat Play... nte
Program Play iii.
Index Search...
Track Programming for Recording a
Tape uu... 15
Notes about the Remote Control
Transmitter cocci... 18
Notes about Handling Compact
Troubleshooting ............... meme 19
Specifications cocci 19
| The serial number is inscribed on the
rear of the unit.
Keep this Owner's Manual i in a safe’
place for future reference.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING
To reduce the risk of fire or electric
shock, do not expose this unit to rain or
moisture,
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
symbol within an equilateral triangle, is”
intended to: alert you to’ the. presence
of uninsulated “dangerous voltage”
within the product's enclosure that may
‘be of sufficient magnitude to constitute’
a risk of alectric shock to parsons.
The exclamation point within .an
equilateral triangle is intended to alert
you to the presence of important
operating and maintenanca (servicing)
instructions in the literature
accompanying the appliance.
1 Read Instructions — All the safety and operating 10 Power Sources — The unit should be connected to a power
instructions should be read before the unit is operated. supply only of the type described in the operating
| , a , instructions or as marked on the unit.
2 Retain Instructions — The safety and operating instructions
should be retained for future reference. 11 Power-Cord Protection — Power-supply cords should be
routed so that they are not likely to be walked on or
3 Heed Warnings — А! warnings on the unit and in the pinched by items placed upon or against them, paying
operating instructions should be adhered to. particular attention to cords at plugs, convenience
| О receptacles, and the point where they exit from the unit.
4 Follow Instructions — All operating and other instructions
should be followed. 12 Cleaning — The unit should be cleaned only as
recommended by the manufacturer.
5 Water and Moisture — The unit should not be used near Y
water — for example, near a bathtub, washbowl, kitchen 13 Nonuse Periods — The power cord of the unit should be
sink, laundry tub, in a wet basement, or near a swimming unplugged from the outlet when left unused for a long
pool, etc. period of time.
6 Carls and Stands — The unit should be used only with a 14 Object and Liquid Entry — Care should be taken so that
cart or stand that is recommended by the manufacturer. objects do not fall into and liquids are not spilled into the
inside of the unit.
6A A unit and cart | |
combination should be moved 15 Damage Requiring Service — The unit should be serviced
with care. Quick stops, by qualified service personnel when:
excessive force, and uneven |
surfaces may cause the unit A The power-supply cord or the plug has been damaged; or
and cart combination to overturn. ME B Objects have fallen, or liquid has been spilled into the unit;
| == or
7 Wall or Ceiling Mounting — The unit should be mounted to C The unit has been exposed to rain; or
a wall or ceiling only as recommended by the D The unit does not appear to operate normally or exhibits a
manufacturer. marked change in performance; or
E The unit has been dropped, or the cabinet damaged.
8 Ventilation — The unit should be situated so that its location | PP 9
or position does not interfere with its proper ventilation. 16 Servicing — The user should not attempt to service the unit
For example, the unit should not be situated on a bed, beyond those means described in the operating
sofa, rug, or similar surface, that may block the ventilation instructions. all other servicing should be referred to
openings; or placed in a built-in installation, such as a qualified service personnel.
bookcase or cabinet that may impede the flow of air |
through the ventilation openings. 17 Power Lines — An outdoor antenna should be located
, . | away from power lines.
Heat — The unit should be situated away from heat |
sources such as radiators, stoves, or other appliances that 18 Grounding or Polarization — Precautions should be taken
produce heat. so that the grounding or polarization is not defeated.
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT
1 To ensure the finest performance, please read this manual 5 Do not use force on switches, knobs or cords. When
carefully. Keep it in a safe place for future reference. moving the set, first turn the unit off. Then gently
disconnect the power plug and the cords connecting to
2 Install your unit in a cool, dry, clean place — away from other equipment. Never pull the cord itself.
windows, heat sources, and too much vibration, dust,
moisture or cold. Avoid sources of hum (transformers, 6 Do not attempt to clean the unit with chemical solvents;
motors). To prevent fire or electrical shock, do not expose this might damage the finish. Use a clean, dry cloth.
to rain and water.
7 Be sure to read the “Troubleshooting” section on common
- Do not operate the unit upside-down. |t may overheat, operating errors before concluding that your unit is faulty.
possibly causing damage. |
4 Never open the cabinet. If a foreign object drops into the
set, contact your dealer.
WARNING
DANGER
Invisible laser radiation when open and interlock failed or
defeated.
Avoid direct exposure to beam.
CAUTION
Use of controls or adjustments or performance of proce-
dures other than those specified herein may result in haz-
ardous radiation exposure.
As the laser beam used in this compact disc player is harmful
to the eyes, do not attempt to disassemble the cabinet. Refer
servicing to qualified personel only.
To avoid electrical shock, do not open the unit. Refer servicing
to qualified personnel only.
DANGER: The use of optical instrument with this product will
increase eye hazard.
FCC INFORMATION (U.S.A.)
1 IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
— This product, when installed as indicated in the instructions
contained in this manual, meets FCC requirements. Modifi-
cations not expressly approved by Yamaha may void your
authority, granted by the FCC, to use the product.
2 IMPORTANT: When connecting this product to accesso-
ries and/or another product use only high quality
shielded cables. Cable/s supplied with this product
MUST be used. Follow all installation instructions. Fail-
ure to follow instructions could void your FCC authoriza-
tion to use this product in the USA.
3 NOTE: This product has been tested and found to com-
ply with the requirements listed in FCC Regulations, Part
15 for Class “B” digital devices. Compliance with these
requirements provides a reasonable level of assurance
that your use of this product in a residential environment
will not result in harmful interference with other electronic
devices.
This equipment generates/uses radio frequencies and, if
not installed and used according to the instructions found
in the users manual, may cause interference harmful to
the operation of other electronic devices. |
Compliance with FCC regulations does not guarantee
that interference will not occur in all installations. If this
product is found to be the source of interference, which
can be determined by turning the unit “OFF” and “ON”,
please try to eliminate the problem by using one of the
following measures:
Relocate either this product or the device that is being af-
fected by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient
the antenna. If the antenna lead-in is 300 ohm ribbon
lead, change the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to dis-
tribute this type of product. If you can not locate the ap-
propriate retailer, please contact Yamaha Electronics
Corp., U.S.A. 6722 Orangethorpe Ave, Buena Park, CA
90620. |
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its sub-
sidiaries.
The solder used in the manufacture of this product contains
LEAD. In addition, the electrical/electronic and/or plastic
(where applicable) components may also contain traces of
chemicals found by the California Health and Welfare Agency
(and possibly other entities) to cause cancer and/or birth
defects or other reproductive harm.
DC NOT REMOVE ANY ENCLOSURE COMPONENTS!
There are no user serviceable parts inside. All service should
be performed by a service representative authorized by
Yamaha to perform such service.
IMPORTANT MESSAGE: Yamaha strives to produce products
that are both user safe and environmentally “friendly”. We
sincerely believe that our products meet these goals.
However, in keeping with both the spirit and the letter of various
statutes we have included the preceding messages and others
in various locations in this manual.
e Before making any connections, switch OFF the power to
the unit and the amplifier or other component.
e Connections should be made to the correct input terminals
of the amplifier or other component.
e |fthe placement of this unit causes noise to other
equipment, such as a tuner, separate them each other.
e If you use the DIGITAL GUTPUT (COAXIAL or OPTICAL)
terminal for the connection, be sure to set the DIGITAL OUT
switch on the rear of this unit to the “ON” position.
Otherwise, this switch should be set to the "OFF” position.
LINE OUT- DISITAL OUT——— This unit
VARIABLE FIXED
© © OPTICAL COAXIAL og] —
© © | | | oa С FES LT
lo В poconoonoseSs о Q
U
To AC outlet
Optical fiber cable Connection cord
Connection cord
(included)
yd Ш
Amplifier
© | МЕ ]
@ — OPTICAL EDAXIAL | o CORO OOO
CO DIGITAL IN J | | | |
``.
Choose one of the ways listed below to connect this unit to your amplifier.
When the LINE OUT (analog) Y terminals of this unit
are used (63)
* Be sure that the left eb and right (“R”) LINE OUT terminals
are connected to the corresponding (left and right) terminals
of the amplifier or other component.
* Connect the “LINE OUT” terminals to the “CD” (or “AUX”)
terminals of the amplifier. If the amplifier does not have
such terminals, use the “TAPE PB” terminals. For additional
details concerning these connections, refer to the operation
instructions for the amplifier being used.
» Connect to either the VARIABLE terminals or the FIXED
terminals. (As a general rule, connect to the FIXED
terminals.)
VARIABLE: The output level of these terminals can be
adjusted by using the OUTPUT LEVEL
control.
FIXED: The output level of these terminals is not
variable.
When the DIGITAL QUT (OPTICAL) terminal of this
unit is used (@)
e Before using this terminal, remove the terminal's cover by
pulling it.
e Make the connection from this terminal to the digital input
terminal of an amplifier or D/A (digital-to-analog) converter
by using a commercially available optical fiber cable.
* Be sure to attach the terminal's cover when this terminal is
not being used, in order to protect the terminal from entry of
dust.
* Use an optical fiber cable that conforms to ElAJ
standards. Other cables might not function correctly.
When the DIGITAL QUT (COAXIAL) terminal of this
unit is used (6)
Make the connection from this terminal to the digital input
terminal of an amplifier or D/A (digital-to-analog) converter by
using a connection cord.
FRONT PANEL
POWER switch Remote control sensor | STOP button
OPEN/CLOSE button
PLAY/PAUSE button
| SEARCH button
Disc tray SKIP button
RANDOM button
REPEAT button
Display panel
YAMAHA A CPEN/CLDSS
Do
pour * | | SHE cer
| [ |
PROG bution Numeric buttons
TAPE button
select button
FILE button PHONES jack
INDEX button OUTPUT LEVEL control
REMOTE CONTROL TRANSMITTER
* The control functions on the main unit and on the remote
control transmitter are virtually identical, with the exceptions
below.
MODE button
SPACE button A-B REPEAT button
* The PLAY/PAUSE button on the main unit has both the
functions of the PLAY button and the PAUSE button on the
remote control transmitter.
=
| =
] FOO a |
y e JOAO
оо
POWER
Г!
Label side
A OPEN/CLOSE
42 OPEN/CLOSE
EPLAY/
00 PAUSE
Disc tray
Display information at disc play Notes
| e After closing the disc tray by pressing the OPEN/CLOSE
button, the display shows the total number of tracks and the
O © total recorded time of the disc for a few seconds.
| | |
Td weld eee 1:08
a Do в в он we TRACK — rr 1 VOIE
= A D SL 1 9 Ce 2
©
@ Shows the track number to be played.
@ Shows the time displays. (Refer to "Selecting time displays”
on page 8.)
(3) Displays the numbers that correspond to the numbers of
“tracks (as high as number 20) on the disc. After each track
is played, its corresponding number disappears so the
number of remaining tracks (and their numbers) can be
seen at a glance.
¢ Additionally, you can close the disc tray by pressing the
PLAY/PAUSE button, a numeric button or the RANDOM
button, or by pressing the front edge of the disc tray gently.
If the tray is closed in these ways, play will begin
automatically, however, the display will not show the total
number of tracks and the total recorded time of the disc.
D>PLAY/
00 PAUSE
PAUSE
DO STOP
or
* To resume play, press the PLAY/PAUSE button again (or
press the PLAY or PAUSE button on the remote control
transmitter).
DIRECT PLAY | SKIP PLAY
Select a desired track using the numeric button. e To play from the beginning of the track following the one
| now playing
+10
cod
= E 7 a 8 og
Bo | кк SKIP Dps
es Jo play from the beginning of the track now playing
KK SKIP [>A
пе = The selected track
5 number is displayed
Example: To select track 25
Press O twice, then immediately press 9 once. e To play from the beginning of the track before the one now
| playing
KK SKIP PLA
5
(twice)
* These operations can also be performed when the unit is in
* You will find more convenience to select a higher track the pause or stop mode.
number by using the remote control transmitter. For
example, track number “32” can be selected by pressing
“+20”, “+10” and “2” continuously.
* If a track number higher than the highest track number on
the disc is selected, the last track on the disc will be played.
<1 SEARCH [>
To advance rapidly * The sound can be heard (although slightly garbled) during
manual search in either direction. This is convenient for
locating a precise position within a track, or for reviewing the
contents quickly.
se Manual search can also be performed while disc play is
(Press and hold.) paused, though no sound will be heard.
To reverse rapidly
<3] SEARCH [>
(Press and hold.)
Automatic spacing
When you are recording a disc onto tape, and if the tracks on
the disc are recorded with an insufficient time space between
them, the tape recorder will not be able to perform blank search
operations correctly. In this case, a recorder search mistake
can be prevented by pressing the auto-SPACE button to insert
spaces of about 4 seconds between the recorded tunes.
SPACE |
Note |
When the automatic-spacing function is in effect, the display of
the total time and of the total remaining time will include each
of the four-second non-recorded intervals placed between
tracks. |
To cancel the automatic-spacing function
SPACE
“SPACE” goes off
from the display.
Selecting time displays
You can select any of the four time displays by pressing the TIME display mode-select button.
e
A
/ |,
noexe LI SNE co
1 28 945 EB 7 8 9 10 m 42
Г |
y
LA
TRACK A Mm !
L INDEX Lf / НЕМА
1 2 3 4a 568 78 9 IN 12
I
f
Г
J
Nö
bi
ее”
(D Elapsed time of the track now playing
@ Remaining time of the track now playing
Total disc play time
@ Total remaining time on the disc
TRACK 1 FT 1 ma 7”.
L mxi вемам A EI
1 89458578 904 12
=
o
{7
ТВАСК 1 1 1 rom
Lo omoex Id |
1 2 3 4 SE 78 8 WN 12
ay
М
<.
—
ча
Ku
—
È
—
Note
The display information can be simplified by pressing the
MODE button. The display mode will change whenever this
button is pressed. |
When you listen with headphones
Connect the headphones to the PHONES jack and adjust the
volume by using the OUTPUT LEVEL control.
* If the VARIABLE (LINE OUT) terminals on the rear of this
unit are connected to the amplifier etc., note that the use of
the OUTPUT LEVEL control will also vary the level of the
signal output to the amplifier.
or
Open/close the control door
When it is not necessary to operate controls inside the control
door, close the door.
To close the door To open the door
Damp the unit to improve sound quality
You can use the equipped pin-point legs to improve sound quality, if you remove the legs covering them. In this case, however,
choose carefully the place where the unit is set. The points of these legs may damage the surface of the furniture and so on.
a a cd 1 red
e
Pine :
т!
La La
dre
=
ч a
Pin-point Leg
You can have the unit play the tracks on a disc in a random sequence selected by the unit's microcomputer.
To perform random-seguence play
RANDOM
To cancel random-sequence play
0 STOP
RANDOM
Notes
s This feature will not function during programming, or during
programmed play.
о [f the POWER switch is set off when the random-sequence
play mode is functioning, when the POWER switch is set on
again, the unit will begin the random-sequence play
automatically. (This feature is available for the timer play.)
e If the SKIP >> button is pressed during random-
sequence play, the next randomly programmed track will be
played. If the SKIP << button is pressed, play will return
to the beginning of the track now being played.
® fa Г This indication appears while the unit is
Li Li mixing up tracks.
o Total remaining time on the disc will not be displayed during
random-sequence play.
You can enjoy three variations of the repeat play.
SINGLE/FULL REPEAT PLAY
You can play any desired track or the entire disc repeatedly by
pressing the REPEAT bution. The repeat-play mode will
change whenever you press the REPEAT button (or the S/F
button on the remote control transmitter).
SINGLE REPEAT
Only a designated track is played repeatedly.
FULL REPEAT
All tracks (the entire disc) are played repeatedly.
* In the programmed-play mode, all programmed tracks are
played repeatedly.
B/F REPEAT
(OFF)
SINGLE
REPEAT Or
REPEAT
FULL
REPEAT
Note
Repeat play is also possible during the programmed-play mode
and the random-sequence play mode.
10
A-B REPEAT PLAY
You can select any two points (A and B) on the disc to be the
start and end points of repeat play.
In the play mode, press the A-B button at the point
where you want to start the repeat play.
Press the A-B button again at the point where you
want to end the repeat play.
To cancel A-B repeat play
Press the A-B button again or S/F button.
You can enjoy listening to your favorite tracks in any desired order using programmed play. As many as 25 tracks can be
programmed for a disc.
Stop the unit.
Ll] STOP
Flashes on and off.
PROG
Select the desired track.
+10 1 = = A — El 7 = 5 |=)
BN
* Repeat step 3 to set more programs.
You can select the same track again.
>PLAY/
10 PAUSE
unprogrammed tracks.
PACS [7] 7 om
Li 1
/ | N
Display information at program play Notes
e The SKIP (<< and =>) button can be used during
| playing, but only within the range of the programmed tracks.
@ s The SEARCH ( << and >> ) button can be used during
| playing to search through all tracks, including
VD Shows the program number for the track to be set next.
@ Shows the selected track number.
@ Shows the total time of the tracks currently programmed.
@ Shows only the numbers of programmed tracks.
* If the total time exceeds 99 minutes and 59 seconds, the
time will not be displayed.
e The PAUSE mode can also be programmed (one time only),
if so desired, by pressing the TAPE button instead of a
numeric button. (In this case, “ O O BP” is illuminated in the
display.)
11
To stop program play
Press the STOP button. The first track number programmed
will be displayed.
To resume play, press the PLAY/PAUSE button. Play will
begin from the beginning of the program.
To cancel a programmed setting
There are several methods, as described below.
e Press the CLEAR button (after programming is completed,
or while the unit is in the stop mode).
e Open the disc tray.
e Switch off the power.
To check programmed data
1. If the unit is in the play mode, press the STOP button.
2. Press the PROG button.
3. Each time the SKIP == button is pressed, the track
numbers and sequential order of the programmed tracks
can be checked one after another. The display of the track
number can be returned (sequentially in reverse order) by
pressing the SKIP << button.
To correct programmed data
1. Follow the procedure described in “To check programmed
data”.
2 Display the track number to be corrected by pressing the
SKIP button. |
3. Press a numeric button to select a track to replace the
displayed one. The previously programmed track will be
cleared from the memory and the new one will be
programmed.
4. After the correction has been completed, once again press
the PROG button or the PLAY/PAUSE button.
This unit has a function that can store (file) program data that has been set. You can play a disc with your favorite programs at any
time without setting it again.
POWER CLEAR
OJ
0 PLAY/PAUSE
OPEN/CLOSE
-STOP
CoCr a
2 9 2 6 С С) 2 СН 0
PROG Numeric buttons
To file a program data
1 Set programs. (Follow steps 1 — 4 on page 11.)
* If the setting has already completed, make sure that
“TRACK” is flashing continuously in the display. If it is
not, once again press the PROG button.
* If the program play is being performed, press the STOP
button, and then press the PROG button.
2 FILE
x |;
= SAVE -
A
12
Notes
e Program data filed in this way can be retained for about two
. weeks, even with the power switched off.
* One program data can be filed for any one disc. If different
program data is filed for a disc, the previous program data
will be deleted from the file, and only the new program data
will be retained in the file.
e Program data for a total of as many as about 100 discs can
be filed at any one time.
To play with program data
1
2 OPEN/CLOSE
‘ | Nd бои
5 a Ва - SAVE -
Pa PO ^
3 If “FILE PROGRAM’ is not illuminated in the display,
press the FILE button.
4
D>PLAY/
00 PAUSE
Notes |
e |f, in step 2, SAVE” does not appear in the display, the disc
does not have its program data in the memory's file.
e To stop the play of the filed program data and change to
ordinary play of the disc, press the FILE button. By this
operation, the disc will be played in the ordinary sequence
of tracks, but the program data in the memory's file for that
disc will not be deleted from the memory. To once again call
out the program data follow steps 3 and 4.
To delete program data from file
1 Set the unit in the stop mode.
To delete all program data from the memory's file
1 Set the POWER off.
2
CLEAR
CLEAR Li
(Press and hold.)
Flashes on and off.
PROG |
SI /
=!) ¡==
7 | >
POWER
A
A
“SAVE” goes off
© => from the display.
CLEAR CL]
(Release.)
13
If the disc includes index numbers, play can be started from any desired index number.
1 Select a track which has index numbers.
+10 1 2 3 < 5 5 7 _B a
E ОНН
INDEX
Select the desired index number.
+10 4
14
Notes
e Not all discs have index numbers. The index system is a
method for sub-dividing tracks into smaller divisions (such
as, for example, the movements within classical
symphonies) for easier location of those parts. The liner
notes with the disc usually tell if such index numbers are
included.
э |f an index number is selected that is higher than any index
number on that disc, play will start from the last index
number point on the disc.
e For some discs, play may begin slightly prior to the actual
designated index point.
e If the disc has no encoded index points, play will begin from
the start of the selected track.
s The index number can be designated only while the INDEX
number display is flashing on and off.
This convenient feature can be used to program tracks on a disc for recording to tape. By only memorizing the tape’s total possible
recording time, the unit will automatically program tracks or help you to program tracks so they will fit onto the tape with the least
amount of unrecorded space remaining at each end of the tape.
pe-programming
This is useful for recording a disc onto tape with the order of tracks unchanged.
НЕРЕАТ
Stop the unit. OD STOP
E
By pressing the REPEAT button, the unit automatically
programs tracks for side A and side B separately consid-
ering the tape’s total time.
If desired, you can automatically insert additional time
space between tracks. (Refer to page 8.)
Begin recording on the tape deck and press the PLAY/
PAUSE button on this unit at the same time.
SPACE .
| # The unit will pause at the end of side A of the tape.
| | Turn the tape over to side B. Resume recording and,
| at the same time, press the PLAY/PAUSE button on
this unit.
Notes
TAPE e All tracks may not be programmed if the tape’s length is not
\ 7 | enough. To program all tracks, use a longer tape.
— | - — e In step 5, you can check the program data for side A and
7 ON side B.
Enter the tape's total possible recording time.
i TOTAL 1 fa + 1
{ и /
Example: For a C-64 tape (32 minutes on each side)
BEE ERNE NEE ES
(D Shows the number of programmed tracks.
@ Shows the total time of programmed tracks.
© Shows the side of the tape.
@ Shows the programmed track numbers.
TRACK / fi
/
I noex tt 1
SPACE - 1 2 3 45 6 7 8 9 NH 12
ro E
Was | E
15
@ Manual tape programming
This is useful for recording desired tracks in any desired order onto tape.
C |
[1] Eden
CS ooo O ©
| |
PROG
и \ | 7
к — PROS 71 1 ora
1.2 3 a4 5 8/7 8|s an 1e
5 Select the track numbers (to be recorded on side B) in
the desired order.
+10
Select the track numbers (to be recorded on side A) in
the desired order. |
+10) 1
SR RE
* Programmed track numbers are illuminated on the dis-
play. You can select a track which can be programmed
for the remaining time of (the side of) the tape from track
numbers flashing on the display, but you cannot select
any darkened track number.
Begin recording on the tape deck and press the PLAY/
PAUSE button on this unit at the same time.
The unit will pause at the end of side A of the tape. Turn
the tape over to side B. Resume recording and, atthe
same time, press the PLAY/PAUSE button on this unit.
4 Program the pause mode.
TAPE
Notes
e If, in step 3 or 5, “E : rr flashes in the display, the track
number just selected cannot be programmed because there
is not enough time remaining on the tape. However, at this
time, if any other track number is flashing continuously in
the display, you can program it instead of the
unprogrammabile one. |
e In step 3 or 5, each time a selection is made, the track
number and the tape’s remaining time will be displayed, and
then the display will change to indicate the number of the
next program.
Notes on tape programming
e To check, cancel or correct program data, refer to page 12.
e The maximum number of tracks that can be programmed is
25 (PROG-01 to PROG-25). If, however, the PAUSE mode
is inserted, it is counted as one track.
16
Random sequential tape programming
The unit will automatically program tracks in random sequential order for recording to tape.
ct
|
E OI A
cTHooooooooso
I
1 Follow steps 1 — 4 on page 15.
RANDOM
* The unit will automatically program tracks for side A and
side B separately considering the tape's total time.
Begin recording on the tape deck and press the PLAY/
PAUSE button on this unit at the same time.
LE The unit will pause at the end of side A of the tape. Turn
the tape over to side B. Resume recording and, atthe
same time, press the PLAY/PAUSE button on this unit.
=
Notes
e Because the programmed data changes every time the
RANDOM button is pressed, the amount of time remaining
at the end of the tape also change accordingly.
e If the tape’s length is not enough, ail tracks cannot be
programmed. In this case, exchange the tape for a longer
one.
e In step 2, you can check the program data for side A and
side B. a.
(D Shows the number of programmed tracks.
2) Shows the total time of programmed tracks.
@ Shows the side of the tape.
@ Shows the programmed track numbers.
* The total time @ will not be displayed if track number 25 or
higher is programmed.
17
NOTES ABOUT THE REMOTE CONTROL TRANSMITTER
Battery installation
Battery replacement
If you find that the remote control transmitter must be used
closer to the main unit, the batteries are weak. Replace both
batteries with new ones.
Notes
e Use only “AA” (RE) batteries for replacement.
e Be sure the polarities are correct. (See the illustration inside
the battery compartment.)
e Remove the batteries if the remote control transmitter will
not be used for an extended period of time.
e |f batteries leak, dispose of them immediately. Avoid
touching the leaked material or letting it come in contact with
clothing, etc. Clean the battery compartment thoroughly
before installing new batteries.
Remote control transmitter operation range
/ \
Remote control
sensor
N Within approximateiy
| 7 m. (23 feet)
Notes
e There should be no large obstacles between the remote
control transmitter and the main unit.
e |fthe remote control sensor is directly illuminated by strong
lighting (especially an inverter type of fluorescent lamp etc.),
it may happen that the remote control transmitter does not
work correctly. In this case, change the position of the main
unit to avoid being lit directly. |
e This compact disc player is designed only for playing
compact discs bearing the (EE. mark. Never attempt to
load any other type of disc into the unit. О
The unit will also play 3-inch (8-cm) compact discs.
e To remove a disc from its storage case, open the case and
then press down at the center; with a finger through the
center hole and the outer edges held as shown in the
illustration, lift the disc out carefully.
e Always handle the disc with care so that its surface is not
scratched.
e Compact discs are not subjected to wear during play, but
damage to the disc surface when the disc is being handled
can adversely affect the disc's play.
e Compact discs are not affected by small particles of dust or
fingerprints on their playing surface, but even so they should
be kept clean. Wipe by using a clean, dry cloth. Do not
wipe with a circular motion; wipe straight outward from the
center. |
e Do not try to clean the disc's surface by using any type of
disc cleaner, record spray, anti-static spray or liquid, or any
other cnemical-based liquid, because such substances
might irreparably damage the disc's surface.
e Do not expose discs to direct sunlight, high temperature or
high humidity for a long period of time, because these might
warp or otherwise damage the disc.
) i © |
To play a 3-inch (8-cm) CD
Place it in the inner recessed area of the disc tray. Do not out
a normal (5-inch/12-cm) CD on top of a 3-inch CD.
TROUBLESHOOTING
If the unit fails to operate normally, check the following points to determine whether the fault can be corrected by the simple
measures suggested. If it cannot be corrected, or if the fault is not listed in the SYMPTOM column, disconnected the power cord
and contact your authorized YAMAHA dealer or service center for help.
The player does not switch ON when the
POWER switch is pressed.
| The power cord is not connected or not a
completely connected.
| Securely connect the power cord. |
The disc tray does not close completely.
A foreign object is obstructing the tray.
Carefully check the disc tray and remove the
foreign object.
The DISC indicator dees not illuminate.
The disc has been loaded upside down.
Load the disc correctly.
The disc is damaged.
Check the disc carefully; replace it if
necessary.
There is moisture on the laser pickup.
Wait 20 to 30 minutes after switching the unit
ON before trying to play a disc.
Play does not begin.
The disc has been loaded upside down.
Reload the disc with the label side up.
The disc is dirty.
Clean the disc.
Play is delayed, or begins at the wrong
place.
The disc may be scratched or damaged.
Check the disc carefully; replace it if
necessary.
No sound.
Improper output cable connections
Connect the cables properly. If the problem
persists, the cables may be defective.
Improper amplifier operation.
Set the amplifier controls to the correct input
selection,
Sound “skips”.
The player is being subjected to vibrations or
impacts.
Relocate the player.
The disc is dirty.
Clean the disc.
Sound “hums”.
Improper cable connections.
Securely connect the audio cables. If the
problem persists, the cables may be defective.
Noise from a nearby tuner.
The tuner is too close to the player.
Move the tuner and player farther apart.
Noise from inside of the disc tray.
The disc may be warped.
Replace the disc.
The remote control transmitter does not
work.
Direct sunlight or lighting (of an inverter type of
flourescent lamp etc.) is striking the remote
control sensor of the main unit.
Change position of the main unit.
SPECIFICATIONS
AUDIO SECTION
Frequency response .............. 2 Hz — 20 kHz, +0.3 dB
De-emphasis equalization ...... naa
Harmonic distortion + noise ...........
S/MNratio .............................
Dynamicrange .......................
Wow & flutter ........................
Output voltage
VARIABLE
FIXED ....... Ll,
= "10" & 2 EB = 4 N & #4 4 # 4&4 + = = = =m = =m =
GENERAL
Power requirements
ln, + 0.5 dB U.S.A. and Canada models ............... 120V, 60 Hz
0.0016% (1 kHz) Australia and U.K. models ................ 240V, 50 Hz
aan, 120 dB Europe model ........................... 230V, 50 HZ
as 100 dB General model ............. 110/120/220/240Y, 50/60 Hz
.... Unmeasurable Power consumption ear arreledradndaaa done uarvooo 30W
Dimensions (WxHxD) .............. 435 x 122 x 346 mm
no 2 OV max (17-1/8” x 4-13/16” x 13-5/8")
2 OV Weight ..............................10kg(221bs.00z.)
640 mV/150 ohms Accessories ................ ."... Connection cord
Remote control transmitter
Batteries (size “AA”, R6)
Please note that all specifications are subject to change
without notice.
19
YAMAHA ELECTRONICS CORPORATION, USA 6722 ORANGETHORPE AVE. BUENA PARK, CALIF. 90620, USA.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE. SCARBOROUGH, ONTARIO M1S 3R1, CANADA -
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, D-2084 RELLINGEN BEI HAMBURG, F.A. OF GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. 17 RUE DES CAMPANULES, LOGNES 77321 MARNE LA VALLEE CEDEX 2, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7J5, ENGLAND YAMAHA CORPORATION
YAMAHA SCANDINAVIA A.B. JA WETTERGRENS GATA 1, BOX 30053, 400 43 VASTRA FROLUNDA. SWEDEN | _
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST. SOUTH MELBOURNE, 3205 VIC.. AUSTRALIA VM57070-0 BWWB, BB Printed in Japan ® ©
"_
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement