Cateye | CC-2000 | Specifications | Cateye CC-2000 Specifications

Setting Values Cross Reference Table (The tire size is marked on both sides of the tire.)
CATEYE TOMO
TIRE SIZE
CYCLOCOMPUTER
Model CC-ST200
U.S. Pat. Nos. 4636769/4642606/5236759/5226340/5264791
and Design Patented
Copyright© 1996 CATEYE Co., Ltd.
CCMST2-970214 Printed in Japan 0687261
3
TROUBLE SHOOTING
•
The following situations do not indicate malfunction of the cyclocomputer. Check the
following before taking to repair.
* When current speed does not appear, short-circuit the contact on the back with metal.
The unit will function normally if the speed display appears.
Display response is slow.
----- Is it at a low temperature under 32°F(0°C)?
----- It returns to normal state when temperature rises.
No display.
----- Has the Lithium Battery in the main unit worn out?
----- Replace the Lithium Battery with a new one.
Incorrect data appear.
----- Execute "All Clear" operation.
Current speed does not appear.
----- Is there anything on the contact of the main unit or of the bracket?
----- Wipe the contact clean.
----- Is the distance between sensor and magnet too far?
----- Are the marking line of the sensor and the center of magnet matched each other?
----- Refer to "Sensor/Magnet Mounting" and re-adjust correctly.
----- Is the wire broken?
----- Replace the Bracket & Sensor part with a new one.
Transmission signal loss in damp or wet conditions.
----- Water or condensation may collect between the bracket sensor and the computer causing an
interruption in the data transmission. Wipe the contacts with dry cloth. Contacts can also be
treated with a water repellent silicon jell from an automotive parts or hardware store. Do not use
industrial water repellent; it may damage the bracket.
When the S/S button is pressed, the unit doesn't activate or stop.
----- Is the unit in the Auto function?
----- The S/S button doesn't function in the Auto function.
TIRE SIZE
TIRE SIZE
20 x 1.75
150
26 x 1.40
200
650 x 38B
211
24 x 1
175
26 x 1.50
199
700 x 18C
207
24 x 3/4 Tubular
178
26 x 1.75
202
700 x 19C
209
24 x 1-1/8 Tubular
179
26 x 1.95
205
700 x 20C
209
24 x 1-1/4
191
26 x 2.00
206
700 x 23C
210
24 x 1.75
189
26 x 2.1
207
700 x 25C
211
24 x 2.00
192
26 x 2.125
207
700 x 28C
214
217
24 x 2.125
196
26 x 2.35
208
700 x 30C
26 x 1(559mm)
191
27 x 1
215
700 x 32C
216
26 x 1(650c)
195
27 x 1-1/8
216
700C Tubular
213
26 x 1.25
195
27 x 1-1/4
216
700 x 35C
217
26 x 1-1/8 Tubular
197
27 x 1-3/8
217
700 x 38C
218
700 x 44C
222
26 x 1-3/8
207
650 x 35A
209
26 x 1-1/2
210
650 x 38A
212
#169-6160/#169-6165
Bracket Sensor Kit/(Long)
#169-6168
Bracket Sensor Kit for Aero Bar
#169-6167
Center Mount Bracket Kit
MAINTENANCE/PRECAUTIONS
• Do not leave the main unit exposed to direct sunlight when the unit is not in use.
• Do not disassemble the main unit, sensor and magnet.
• Don't pay too much attention to your computer's functions while riding! Keep your eyes on the
road and duly consider to traffic safety.
• Check relative position of sensor and magnet periodically.
• For cleaning, use neutral detergent on soft cloth, and wipe off later with dry cloth. Do not apply
paint thinner, benzine, or alcohol, to avoid damages on the surface.
• If there is mud, sand or the like clogs between the button and the body, the movement of the
button may be disturbed. Softly wash away such objects with water.
#169-6169
SPECIFICATIONS
Heavy Duty Wire and Bracket Sensor Kit
130cm - 229cm
11ø - 36ø (S:11 - 26ø L:21 - 36ø)
70cm
Lithium Battery (CR1620/CR1616) x 1
Approx. 3 years(The life of the first factory-loaded battery may
be shorter than this period.)
Dimension/Weight
1-15/16" x 1-25/32" x 5/8" (49 x 45 x 16 mm) / 0.74 oz (21 g)
Controller
4-bit 1-chip Microcomputer (Crystal Controlled Oscillator)
Display
Liquid Crystal Display
Sensor
No Contakt Magnetic Sensor
Operating Temperature Range 0°C - 40°C(32°F - 104°F)
* The specifications and design are subject to change without notice.
Bracket Sensor Kit for Aero Bar
#169-9731
Applicable Cycle Sizes
Applicable Fork Diameter
The length of the wire
Power Supply
Battery Life
LIMITED WARRANTY
1-Year Warranty for Main Unit Only
(Accessories/Attachments and Battery Consumption excluded)
#169-6170
Attachment Kit
#169-6280
Universal Sensor Band
If trouble occurs during normal use, the part of the Main Unit will be repaired or replaced free of charge. The service must be
performed by Cat Eye Co., Ltd. To return the product, pack it carefully and remember to enclose the warranty certificate with
instruction for repair. Please write or type your name and address clearly on the warranty certificate. Insurance, handling and
transportation charges to our service shall be borne by person desiring service.
(Address for service)
CO.,LTD.
2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546 Japan
Attn.: CAT EYE Customer Service Section
Service & Research Address for United States Consumers:
CATEYE Service & Research Center
1705 14th St. 115 Boulder, CO 80302
Phone:
303-443-4595
Toll Free:
800-5CATEYE
Fax:
303-473-0006
e-mail: CatEyeUSA@aol.com
#166-5120
#169-6180
Wheel Magnet
Lithium Battery (CR1620)
E
OPERATING INSTRUCTIONS
•Test (Fig.16)
Mount main unit. If main display does not show any figures, press either M button or S/S button to
release from power saving function. Spin the wheel to check if sensor pulse symbol flashes. If not,
adjust relative positions of magnet and sensor following the instructions.
sensor band A
sporkes
sensor
band B
screw
sensor band A
parallel
sensor
band A
Fig.10
The following must be completed before operating.
(1) How to measure wheel circumference (L) of your bike (Fig.4)
L
Put a mark on the tire tread and ride the bike one full wheel revolution. Mark the
start and the end of the revolution on the ground and then measure the distance
between the two marks. This is your actual circumference. Or, the "Selecting
Values Cross Reference Table" tells you an approximate circumference according to tire size.
Fig.4
(2) Setting Speed Scale
Preform all clear operation. All displays will illuminate. Then mile/h alone will be
displayed as illustrated in fig.5. Km/h and mile/h are alternately displayed with
each press of S/S button. Press M button to set desired speed scale. The display will change as fig. 6.
Fig.5
(3) Setting the wheel circumference (Fig.6)
The standard wheel circumference of 216 cm for 27" wheel is displayed. When
using 216 cm without revision, press M button. ODO will be displayed and 216
cm is set. For revision, press S/S button to increase the number by one. To
increase rapidly, hold down the button. When the desired number appears,
press M button. ODO will be displayed, and the desired number is set.
Fig.6
(4) Resetting or changing the wheel circumference
Set main unit in ODO with M button, and stop it with S/S button. Press SET button. The stored number
will flicker on the sub-display. Revise the number as desired according to the instructions in (3).
Setting the clock time (Fig.7)
sensor band B
rubber pad
rubber pad
Fig.8
Bracket
8. Bracket Rubber Pad (2 pcs.)
Wire
9. Wire Securing Tape
Sensor
10. Sensor Band Screw
Sensor Bands-A (S)(L)
Sensor Bands-B
Magnet
Sensor Band Rubber Pad
MAIN UNIT PREPARATION
MOUNTING TO BIKE
• The spokes must run correctly through the inside the magnet as in fig.8.
• Attach the sensor with Sensor Bands-A-B to the right fork. Choose a band that fits the fork diameter (S size for up to 24ø, L for oversize).
1. Insert the band-B into the slit of the band-A, and put the rubber pad inside of the band-A(fig. 9).
Adjust the length in order that the screw-fastening part of the bands are parallel when mounted
to the fork(fig. 10). *To pull out the band B from band A, tug strongly.
2. Mount the adjusted bands to the fork along with the sensor, by temporarily tightening the
screw(fig. 11).
3. Align the magnet's center and the sensor's marking line(fig. 12), and make sure of 2mm clearance between the magnet and sensor (fig. 13). Then tighten the screw securely. Cut the excess
of the band-B with a nipper or the like.
• Secure the wire with tape as fig. 14. Wind the wire round the outer cable and adjust length. Loosen
the wire in the area marked with the arrow so that the wire does not hinder handlebar operation.
• Use either 1mm- or 2 mm-thick pads if necessary, according to handlebar diameter. Attach the
bracket close to the handlebar stem (fig. 15).
• Slide main unit onto the bracket from front until it clicks into position. To remove, pull it off forward
while pushing down the lever. (fig. 16)
magnet
1.
2.
3.
4.
5.
6.
7.
E
S/S (Start/Stop) Button
Set Button
Battery Case Cover
Contact
EY
H.
I.
J.
K.
T
Main Display (Speed)
Sensor Pulse Symbol
Mode Symbol
Speed Scale Symbol
Auto Mode Symbol
Sub-Display (Selected Function)
M (Mode) Button
CA
A.
B.
C.
D.
E.
F.
G.
sensor
Fig.11
fork
Fig.9
bracket
Press M button over 2 seconds to select
, and stop it with S/S button. Then
press SET button, and minutes flash. Press S/S button to advance minutes by
one. To advance rapidly, hold down the button. Set the time one or two minutes
ahead of the current time. Then press M button, and hours will flash. Use S/S
button the same way. Press SET button to complete time setting. *When you
press the SET button, the undisplayed seconds will turn to zero. For accuracy,
set by the radio time signal.
Fig.7
outer cable
magnet
markingline
of sensor
MEASURING AND DISPLAY FUNCTIONS
sensor
rubber pad
center of
magnet
wire securing
tape
about 2mm
Fig.13
Fig.12
Current Speed
0.0(3.0) - 65 mile/h(27inch) ±1 mile/h under31 miles/h
This is always displayed on the main display and updated once a second.
SPD
screw cap
Fig.15
DST
lever
0.0 - 9999.9 mile ±0.1 mile
This is continuously measured until battery wears down or all clear operation is
done. At 10,000 miles(km), it returns to zero and counting begins anew.
ODO Total Distance (Odometer)
ODO
wire
Fig.14
HOW TO REPLACE THE BATTERY
OPEN
Trip Distance
0.00 - 999.99 mile ±0.01 mile
The trip distance from start to current point is displayed. With Reset operation, it
returns to zero.
DST
Fig.16
DST
Turn main unit over, remove battery case cover with coin and insert a
new lithium battery properly (CR1620 or CR1616) with the (+) pole upward (fig.17), and close the cover securely.
* Please make sure to do the All Clear operation after replacing battery, and to set the unit again.
CLOSE
Elapsed Time
0:00'00" - 9:59'59" ±0.003 %
Elapsed time is measured from start to current point, in units of hours, minutes and
seconds. At 10 hours, it returns to zero and counting begins anew. With Reset
operation, it returns to zero.
TM
TM
Fig.17
BUTTON FUNCTION
Changes the display in the order shown in fig. 1, and data is displayed on the subdisplay. *If held over 2 seconds, 12-hour clock appears.
ODO
• S/S button
TM
Starts and stops the measurement of trip distance and elapsed time. During operation, speed scale symbol flashes. In Auto Function, this button is invalid.
AVS
AVS
DST
MXS
This is for setting the wheel circumference and clock time, switching on/off Auto Function and to clear
all present data and any irregularity. When pressed in stop state in each mode, the following can be
revised.
• In ODO mode --------------------- Wheel circumference
• In
mode ----------------------- 12-hour clock
• In TM, DST or AVS mode ----- On/off the Auto function
12-hour clock time
Reset Operation: (Fig.2)
RESET
Fig.2
All Clear Operation: (Fig.3)
ALL CLEAR
0:00' - 11:59' ±0.003 %
The current time is displayed by a 12-hour clock.
AUTO (AUTOMATIC START/STOP) FUNCTION
DST
When M button, S/S and set buttons are pressed simultaneously, all data
stored (ODO, speed scale, Wheel circumference and clock time) is erased.
All displays illuminate, then mile/h symbol illuminates. This should only be
executed after replacing battery or when irregular display occurs due to
static electricity, etc. Since all memories are erased, set necessary data
again according to "Main Unit Preparation".
0.0(3.0) - 65 mile/h(27inch) ±1 mile/h
With Reset operation, it returns to zero and counting begins anew.
MXS Maximum Speed
Fig.1
• SET Button
Select any mode except ODO, then press M button and S/S button simultaneously. MXS, AVS, DST and TM will become zero. (When done in ODO,
registered wheel circumference will be displayed.)
AVS Average Speed
0.0 - 65.0mile/h ±0.3 mile/h
The average speed from start to current point is displayed within 27 hours 46
minutes 39 seconds (99,999 seconds) or 999.99 miles (km). If either is exceeded,
(.E) is displayed and calculation ceases.
MXS
• M button (Fig.1)
AUTO
This function switches the main unit to start or stop automatically, in which AUTO
symbol appears on the screen, and you are free from pressing S/S button each
time.
•How to switch on/off the Auto Function.
In TM, DST or AVS, this function switches on/off with each press of SET button.
When on, AUTO symbol appears. *With this function, it ceases measuring
elapsed time during a stop.
* 2 seconds may be elapsed if mount the main unit to the bracket with this function on.
POWER SAVING FUNCTION
Fig.3
When main unit is left without receiving any signal for 60-70 minutes continuously,
power supply is shut down and main unit will display (
) only as the figure. By
pressing M button or S/S button, or by receiving signal, this function is released.
Download PDF