Avtec Chinook Specification Sheet, Model VDV

Avtec Chinook Specification Sheet, Model VDV
Exhaust Only V-Bank Island Canopy
for Light and Medium
Duty Cooking Equipment
CHINOOK Value Ventilation Exhaust Only Filter model VDV
Description:
This is a V-bank exhaust only single Island style
canopy.
This V-Bank island style canopy is best suited for use
over a single bank of cooking equipment. This hood
is recommended for use over light and medium duty
cooking appliances.
Specifications:
A single shell exhaust only Type I island canopy. The hood(s) shall be UL 710 Listed without (with) fire damper for 400 or 600
degree Fahrenheit rated cooking appliances. Canopy constructed of stainless steel on all exposed surfaces and aluminized steel
on all non-exposed surfaces. Canopy shall have all welded exterior joints and seams. Canopy construction shall conform to NFPA
96 standards. All exposed welds are to be ground and polished to match finish requirements. Canopy is to meet NSF standards
for construction and UL standards for operation. UL Listed aluminum baffle style grease filters to run full length of exhaust hood.
Grease trough(s) to be easily removable and sloped to removable grease cup(s). UL Listed globe type incandescent light fixtures
mounted on 36” center lines.
Standard Features:
• UL Listed aluminum grease filters
•UL Listed globe light(s)
•Removable grease trough & cup(s)
•Hanging brackets
•Exhaust and supply collars installed
•1” Thick supply air plenum insulation
•Stainless steel construction where visible
1055 Mendell Davis Drive, Jackson, MS 39272
888-994-7636, unifiedbrands.net
Please reference our website for the most
updated product information and specifications.
Optional Accessories:
All stainless steel construction
UL Listed stainless steel grease filters
14” Utility cabinet
Electrical control panel
Pre-plumbed fire suppression
Stainless steel top enclosures
Light and fan switches
Recessed fluorescent light fixtures
Recessed incandescent light fixtures
Stainless steel wall panel
Stainless steel side skirts
Exhaust fan / cooking equipment interlock control
UL Listed exhaust volume damper available on
all units with (2) exhaust collars
Melink Intelli-Hood® control systems
Avtec CHINOOK Value Ventilation, Page 2
PP SPEC1026 Rev. C
Revised 05/09
Model VDV
Light Duty Temperature Cooking Equipment – 400°F (Light duty ranges, roasters, ovens, steamers, etc.)
Medium Duty Temperature Cooking Equipment – 400-600°F (Rotisseries, ranges, grills, fryers, etc.)
Heavy Duty Temperature Cooking Equipment – 600°F (Gas char-broilers, woks, upright broilers, etc.)
Length
4’-0”
5’-0”
6’-0”
7’-0”
8’-0”
9’-0”
10’-0”
11’-0”
12’-0”
13’-0
14’-0”
15’-0”
16’-0”
400 Degree Light Duty
Cooking Equipment
Exhaust CFM
CFM @
Duct Collar
.75 SP
1400
10 x 12
1750
12 x 14
2100
12 x 16
2450
12 x 18
2800
12 x 22
3150
12 x 24
3500
12 x 26
3850
12 x 28
4200
12 x 32
4550
2-12 x 18
4900
2-12 x 18
5250
2-12 x 20
5600
2-12 x 22
400-600 Medium Duty
Cooking Equipment
Exhaust CFM
CFM @
Duct Collar
1.00” SP
1800
12 x 14
2250
12 x 16
2700
12 x 20
3150
12 x 24
3600
12 x 28
4050
12 x 30
4500
12 x 34
4950
12 x 38
5400
2 12 x 20
5850
2 -12 x 22
6300
2 -12 x 24
6750
2 -12 x 26
7200
2 - 12 x 28
600 Degree Heavy Duty
Cooking Equipment
Exhaust CFM
CFM @
Duct Collar
1.25”SP
2000
12 x 16
2500
12 x 18
3000
12 x 22
3500
12 x 26
4000
12 x 30
4500
12 x 34
5000
12 x 38
5500
12 x 42
6000
2-12 x 22
6500
2-12 x 24
7000
2-12 x 26
7500
2-12 x 28
8000
2-12 x 30
Note: Greater exhaust air flow rates may be required for each specific installation to obtain complete vapor and smoke removal.
Note: Hoods over 12’-0”in length require two exhaust duct collars. Exhaust collar sizing is based on an average range of 1600 FPM. Duct collars are
located on centerline of canopy, unless otherwise specified. Hoods with two exhaust collars have them located on ¼ hood length lines unless otherwise
specified. Canopy is to have a minimum 6” overhang on all exposed sides and the front and rear leading edge of the hood to the perimeter of the cooking
equipment surface.
1055 Mendell Davis Drive, Jackson, MS 39272, 888-994-7636, unifiedbrands.net
© 2009 Unified Brands. All Rights Reserved. DOVER® and the DOVER® Logo are registered
trademarks in the United States [and various other countries] of Unified Brands, a
wholly-owned subsidiary of Dover Corporation.
NFPA-96
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement