AXIOMTEK | SBC81203 Series | User`s manual | AXIOMTEK SBC81203 Series User`s manual

SBC81203 Series
®
Intel CoreTM Duo/ Pentium D
®
®
Pentium 4/Celeron
PICMG 1.0 Single Board Computer
User’s Manual
®
Disclaimers
This manual has been carefully checked and believed to contain
accurate information. AXIOMTEK Co., Ltd. assumes no responsibility
for any infringements of patents or any third party’s rights, and any
liability arising from such use.
AXIOMTEK does not warrant or assume any legal liability or
responsibility for the accuracy, completeness or usefulness of any
information in this document. AXIOMTEK does not make any
commitment to update the information in this manual.
AXIOMTEK reserves the right to change or revise this document
and/or product at any time without notice.
No part of this document may be reproduced, stored in a retrieval
system, or transmitted, in any form or by any means, electronic,
mechanical, photocopying, recording, or otherwise, without the prior
written permission of AXIOMTEK Co., Ltd.
CAUTION
If you replace wrong batteries, it causes the danger of explosion. It is
recommended by the manufacturer that you follow the manufacturer’s
instructions to only replace the same or equivalent type of battery,
and dispose of used ones.
©Copyright 2008 AXIOMTEK Co., Ltd.
All rights reserved
October 2009, Version A3
Printed in Taiwan
ii
ESD Precautions
Computer boards have integrated circuits sensitive to static electricity.
To prevent chipsets from electrostatic discharge damage, please take
care of the following jobs with precautions:
„
Do not remove boards or integrated circuits from their anti-static
packaging until you are ready to install them.
„
Before holding the board or integrated circuit, touch an unpainted
portion of the system unit chassis for a few seconds. It
discharges static electricity from your body.
„
Wear a wrist-grounding strap, available from most electronic
component stores, when handling boards and components.
Trademarks Acknowledgments
AXIOMTEK is a trademark of AXIOMTEK Co., Ltd.
®
Windows is a trademark of Microsoft Corporation.
Phoenix & AWARD are trademarks of Phoenix Technology Ltd.
IBM, PC/AT, PS/2, VGA are trademarks of International Business
Machines Corporation.
®
TM
®
®
®
Intel Core 2 Duo Pentium D, Pentium 4, Celeron D are
trademarks of Intel Corporation.
Winbond is a trademark of Winbond Electronics Corp.
Other brand names and trademarks are the properties and registered
brands of their respective owners.
iii
Table of Contents
Disclaimers ........................................................................................................... ii
ESD Precautions ................................................................................................. iii
CHAPTER 1 INTRODUCTION ..................................................................................... 1
1.1
Specifications .......................................................................................... 2
1.2
Utilities Supported ................................................................................... 3
1.3
Block Diagram ......................................................................................... 4
1.4
I/O Bracket .............................................................................................. 4
CHAPTER 2 JUMPERS AND CONNECTORS ............................................................ 5
2.1
Board Dimensions ................................................................................... 5
2.2
Board Layout ........................................................................................... 6
2.3
Jumper Settings ...................................................................................... 7
2.3.1
COM2 Mode Select Jumpers (JP4, JP5, JP6) ................................. 7
2.3.2
CMOS Clear Jumper (JP15) ............................................................ 8
2.4
Connectors .............................................................................................. 9
2.4.1
Print Port Connector (PRN1) ......................................................... 10
2.4.2
Audio Connector (CN1) .................................................................. 11
2.4.3
Serial Port Interface Connectors (COM1, COM2) .......................... 11
2.4.4
ATX 4 Pin 12V In Connector (CN2)................................................ 12
2.4.5
Floppy Disk Port Connector (FDD1)............................................... 12
2.4.6
Parallel IDE Interface Connector (IDE1) ........................................ 13
2.4.7
SATA Connectors (SATA1~4)........................................................ 14
2.4.8
USB Connectors (USB1~2)............................................................ 14
2.4.9
Front Panel Connector (CN5)......................................................... 15
2.4.10
AXIOM ACPI Connector (CN4) ...................................................... 16
2.4.11
Internal Mouse/Keyboard Connector (MS1/KB1) ........................... 16
CHAPTER 3 HARDWARE INSTALLATION .............................................................. 17
3.1
Installing the Processor ......................................................................... 17
3.2
Installing the Memory ............................................................................ 22
CHAPTER 4 HARDWARE DESCRIPTION................................................................ 23
4.1
Microprocessors .................................................................................... 23
4.2
BIOS...................................................................................................... 23
4.3
System Memory..................................................................................... 23
4.4
I/O Port Address Map............................................................................ 24
CHAPTER 5 PHOENIX-AWARD BIOS UTILITY ....................................................... 25
5.1
Entering Setup....................................................................................... 25
5.2
Control Keys .......................................................................................... 26
5.3
Getting Help .......................................................................................... 26
5.4
The Main Menu ..................................................................................... 27
5.5
Standard CMOS Setup Menu................................................................ 28
5.6
Advanced BIOS Features...................................................................... 31
5.7
Advanced Chipset Features .................................................................. 36
5.8
Integrated Peripherals ........................................................................... 37
5.9
Power Management Setup .................................................................... 41
iv
5.10
5.11
5.12
5.13
5.14
5.15
5.16
PnP/PCI Configuration Setup................................................................ 43
PC Health Status................................................................................... 45
Frequency/Voltage Control.................................................................... 46
Load Optimized Defaults ....................................................................... 47
Set Supervisor/User Password ............................................................. 48
Save & Exit Setup ................................................................................. 49
Exit Without Saving ............................................................................... 50
CHAPTER 6 INSTALLATION OF DRIVERS ............................................................. 51
6.1
Installing Chipset Driver ........................................................................ 51
6.2
Installing VGA Driver ............................................................................. 54
6.3
Installing LAN Driver.............................................................................. 58
6.4
Installing Audio Driver ........................................................................... 60
APPENDIX A WATCHDOG TIMER ........................................................................... 63
APPENDIX B PCI IRQ ROUTING .............................................................................. 65
APPENDIX C WHAT IS SATA RAID FUNCTION ?................................................... 67
APPENDIX D MEMORY I/O ADDRESS..................................................................... 69
v
MEMO
vi
SBC81203 LGA775 SBC User’s Manual
CHAPTER 1
INTRODUCTION
The SBC81203 PICMG 1.0 full-size Single Board Computer supports
TM
®
®
®
®
Intel Core 2 Duo, Pentium D, Pentium 4 and Celeron
processors, at FSB 533/800/1066 MHz. The board integrates chipsets
®
Intel 945G and ICH7R that deliver outstanding system performance
through high-bandwidth interfaces, multiple I/O functions for
interactive applications and various embedded computing solutions.
There are two DDR2 DIMM sockets for dual channel DDR2 533/667,
maximum memory capacity up to 4GB. The board also features
Ethernet 10/100/1000Mb, Dual PCI-Express LAN, four serial ATA
channels for four serial ATA hard drives at maximum transfer rate up
to 300MB/sec, six USB 2.0 high speed compliant, built-in high
definition audio codec that can achieve the best stability and reliability
for industrial applications.
Introduction
1
SBC81203 LGA775 SBC User’s Manual
1.1
Specifications
®
TM
®
®
z
CPU: Intel Core 2 Duo, Pentium D, Pentium 4 and
®
Celeron processors
z
System Chipset: Intel 945G & ICH7R
z
CPU Socket: LGA775
z
Front-Side Bus: 533/800/1066MHz
z
BIOS
®
„
Phoenix-Award PnP Flash BIOS
z
System Memory
„
Two x 240-pin DDR2 DIMM sockets
„
Maximum up to 4GB DDR2 memory
„
Support DDR533/667 memory
z
L2 Cache: integrated in CPU
z
IDE Interface
„
One IDE connector and up to two IDE devices, Ultra DMA
ATA33/66/100 supported
z
Onboard Multi-I/O
„
Parallel Port: one bi-directional with ECP/EPP/SPP support
„
Serial Port: one for RS-232 (COM1) and one port for
RS-232/422/485 (COM2)
„
Floppy controller: supports two drives (1.44MB for each)
z
USB Interface
„
Six USB ports compliant with USB Spec. Rev. 2.0
z
VGA Controller
„
Chipset Integrated VGA Controller and Supports up to
2048x1536 at 75 Hz resolution on non-interlaced CRT
monitors
z
Ethernet
2
®
„
The LAN1/LAN2: Intel 82573L Ethernet controller supports
10/100/1000Mb
„
Dual PCI-Express LAN
Introduction
SBC81203 LGA775 SBC User’s Manual
„
Wake On LAN support
z
Serial ATA
„
Built-in four SATA/SATA II ports onboard support the
maximum transfer rate up to 300MB/sec
z
Audio
„
Realtek ALC203 Audio Codec onboard
z
Hardware Monitoring
„
Controller: Winbond W83627HF-AW detection of CPU
temperature, system temperature, power failure and fan
speed
z
Watchdog Timer
„
Software programmable time interval and hardware reset
only.
„
1~256 seconds; up to 256 levels
z
Dimensions: 338x 126mm (6 layer)
NOTE All specifications and images are subject to change
without notice.
1.2
Utilities Supported
®
z
Intel 945G Utility and Drivers
z
VGA Drivers
Ethernet Utility and Drivers
Audio Utility and Drivers
z
z
Introduction
3
SBC81203 LGA775 SBC User’s Manual
1.3
Block Diagram
1.4
I/O Bracket
4
Introduction
SBC81203 LGA775 SBC User’s Manual
CHAPTER 2
JUMPERS AND CONNECTORS
2.1
Board Dimensions
Jumpers and Connectors
5
SBC81203 LGA775 SBC User’s Manual
2.2
6
Board Layout
Jumpers and Connectors
SBC81203 LGA775 SBC User’s Manual
2.3
Jumper Settings
Proper jumer settings configure the SBC81203 to meet your
application purpose.
2.3.1 COM2 Mode Select Jumpers (JP4, JP5, JP6)
These jumpers select the COM2 port’s communication mode to operate
RS-232 or RS-422/485.
Description Function
COM2
RS-232
(Default)
Jumper Setting
JP4
1
3
5
7
2
4
6
8
JP4
RS-422
1
3
5
7
1
3
5
7
JP6
2
4
6
1
3
5
JP5
2
4
6
8
1
3
5
2
4
6
8
1
3
5
JP4
RS-485
Jumpers and Connectors
JP5
1
3
5
2
4
6
JP6
2
4
6
1
3
5
2
4
6
1
3
5
JP5
2
4
6
JP6
2
4
6
7
SBC81203 LGA775 SBC User’s Manual
2.3.2 CMOS Clear Jumper (JP15)
You may need to use this jumper is to clear the CMOS memory if
incorrect BIOS settings.
Description Function
Jumper Setting
CMOS Clear Normal
(Default)
Clear
CMOS
8
Jumpers and Connectors
SBC81203 LGA775 SBC User’s Manual
2.4
Connectors
Connectors connect the CPU card with other parts of the system.
Loose or improper connection might cause problems. Make sure all
connectors are properly and firmly connected.
Connectors
Audio Output
Label
CN1
Connectors
Label
USB 1
USB1, 2
Parallel Port
PRN1
USB 3, 4
USB5, 6
COM1 Port
COM1
USB 2
USB3, 4
ATX 4 Pin 12V In
CN2
Front Panel
CN5
CD AUX In
AUX1
System FAN1
FAN2
COM2 Port
COM2
System FAN2
FAN3
Floppy Port
FDD1
AXIOM ACPI
CN4
RJ-45 Port1
LAN1
CPU FAN
FAN1
RJ-45 Port2
LAN2
LGA775 Socket
P-ATA IDE Port
IDE1
Mouse Connector
MS1
CompactFlash
Socket (optional)
CF1
Keyboard Connector
KB1
LGA775
S-ATA Port 4
SATA4 S-ATA Port 2
SATA2
S-ATA Port 3
SATA3 S-ATA Port 1
SATA1
VGA Port
Jumpers and Connectors
CN3
9
SBC81203 LGA775 SBC User’s Manual
2.4.1 Print Port Connector (PRN1)
Print Port Connector [Default]
This board has a multi-mode parallel port to support:
1. Standard Mode:
IBM PC/XT, PC/AT and PS/2™ are compatible with bi-directional
parallel port.
2. Enhanced Mode:
Enhance parallel port (EPP) is compatible with EPP 1.7 and EPP 1.9
(IEEE 1284 compliant).
3. High Speed Mode:
Microsoft and Hewlett Packard extended capabilities port (ECP) is
IEEE 1284 compliant.
Pin
10
Signal
Pin
Signal
1
Strobe#
2 Data 0
1
2
3
Data 1
4 Data 2
3
4
5
Data 3
6 Data 4
5
6
7
8
9
10
11
12
13
14
7
Data 5
8 Data 6
9
Data 7
10 Acknowledge #
11 Busy
12 Paper Empty #
13 Printer Select
14 Auto Form Feed #
15
16
15 Error #
16 Initialize #
17
18
17 Printer Select In #
18 GND
19
20
19 GND
20 GND
21
22
21 GND
22 GND
23
24
23 GND
25 GND
24 GND
25
26
26
Jumpers and Connectors
SBC81203 LGA775 SBC User’s Manual
2.4.2
Audio Connector (CN1)
CN1 is a 10-pin connector to support the audio interface.
Pin
1
Signal
Pin
MIC-IN
Signal
2 GND
3
Line In L
4 GND
5
Line In R
6 GND
7
Audio Out L
8 GND
9
Audio Out R
10 GND
2.4.3 Serial Port Interface Connectors (COM1, COM2)
The serial interface for the board consists of COM1 port (COM1) and
COM2 (COM2) supports RS-232/RS-422/RS-485.
Pin
Signal
Pin
1
Data Carrier Detect
(DCD)
2
3
Receive Data (RXD)
4
5
Transmit Data (TXD)
6
7
Data Terminal Ready
(DTR)
8
9
Ground (GND)
10
Signal
Data Set Ready (DSR)
Request to Send (RTS)
Clear to Send (CTS)
Ring Indicator (RI)
NC
COM2 Serial Port 10-pin (Box-header) Connector Pin Assignment list
Pin #
Signal Name
RS-422
RS-485
1
2
TXNo connector
DATANo connector
3
TX+
DATA+
4
No connector
No connector
5
RX+
No connector
6
No connector
No connector
7
8
RXNo connector
No connector
No connector
9
GND
GND
10
GND
GND
Jumpers and Connectors
11
SBC81203 LGA775 SBC User’s Manual
2.4.4 ATX 4 Pin 12V In Connector (CN2)
You can connect it to the ATX12V power supply for CPU Core Voltage.
Note: Make sure your ATX12V power supply can provide 16A on the
+12V lead and at least 1A on the +5V standby lead (+5VSB).
The minimum recommended wattage is 250W or 300W for a
fully configured system. The system may become unstable and
may experience difficulty powering up if the power supply is
inadequate.
Pin
Signal
1
GND
2
GND
3
+12V
4
+12V
2.4.5 Floppy Disk Port Connector (FDD1)
The board provides a 34-pin header type connector, FDD1, supporting
up to two floppy drives. The floppy drives may be any one of the
following types: 5.25" 360KB/1.2MB and 3.5" 720KB/1.44MB/2.88MB.
Pin
Signal
Pin
Signal
Pin
1
GND
2
Reduce write current
3 GND
4
N/C
5
GND
6 N/C
7
GND
8
Index #
9 GND
Signal
10 Motor enable A #
11 GND
12 Drive select B #
13 GND
14 Drive select A #
15 GND
16 Motor enable B #
17 GND
18 Direction #
19 GND
20 STEP #
21 GND
22 Write data #
23 GND
24 Write gate #
25 GND
26 Track #
27 GND
28 Write protect #
29 GND
30 Read data #
31 GND
32 Side 1 select #
33 GND
34 Disk change #
12
Jumpers and Connectors
SBC81203 LGA775 SBC User’s Manual
FDD1
2.4.6 Parallel IDE Interface Connector (IDE1)
The board provided one IDE Port to support maximum up to two IDE
devices.
Pin
Description
Pin
Description
Pin
Description
1
Reset #
2
GND
3
Data 7
4
Data 8
5
Data 6
6
Data 9
7
Data 5
8
Data 10
9
Data 4
10
Data 11
11
Data 3
12
Data 12
13
Data 2
14
Data 13
15
Data 1
16
Data 14
17
Data 0
18
Data 16
19
GND
20
N/C
21
N/C
22
GND
23
IOW #
24
GND
25
IOR #
26
GND
27
IOCHRDY
28
N/C
29
N/C
30
GND-Default
31
Interrupt
32
N/C
33
SA1
34
N/C
35
SA0
36
SA2
37
HDC CS0 #
38
HDC CSI #
39
HDD Active #
40
GND
IDE1
Jumpers and Connectors
13
SBC81203 LGA775 SBC User’s Manual
2.4.7 SATA Connectors (SATA1~4)
These SATA connectors are for high-speed SATA interface ports and
they can be connected to hard disk devices.
Pin
Signal
1
GND
2
SATA_TX+
3
SATA_TX-
4
GND
5
SATA_RX-
6
SATA_RX+
7
GND
7
1
2.4.8 USB Connectors (USB1~2)
These Universal Serial Bus (USB) connectors on this board are for
installing versatile USB interface peripherals. These are 10-pin
standard USB connectors.
Pin
Signal
Pin
Signal
1 USB
POWER
3 USB P0-
2
USB POWER
4
USB P1+
5 USB P0-
6
USB P1+
7 USB GND
8
USB GND
9 NC
10 GND
USB USB USB USB
GND P0- P0- Power
1
10
14
2
GND USB USB USB USB
GND P1+ P1+ Power
Jumpers and Connectors
SBC81203 LGA775 SBC User’s Manual
2.4.9 Front Panel Connector (CN5)
„
Power LED
Pins 1, 3, 5 connect the system power LED indicator to its
respective switch on the case. Pin 1 is +, and pin 5 assigned to -.
Pin 3 is defined as NC.
„
External Speaker and Internal Buzzer Connector
Pins 2, 4, 6, 8 can be connected to the case-mounted speaker unit
or internal buzzer.
„
Hardware Reset
Pins 11 and 12 are designed for Hardware Reset.
„
HDD Activity LED
This connector extends to the hard drive activity LED on the control
panel. This LED will flash when the HDD is being accessed. Pins 13
and 14 can be connected to the hard disk drive and front panel
HDD LED.
„
Power Button
Pins 9 and 10 connect the front panel’s ATX power button to the
card, which allows users to control ATX power on or off.
Jumpers and Connectors
15
SBC81203 LGA775 SBC User’s Manual
2.4.10 AXIOM ACPI Connector (CN4)
It is to support remote power on/off for turning off the system through
software control while using the ATX-compliant power supply.
Pin
Signal
Pin
Signal
1
EXTSMI
2
GND
3
POWER BUTTOM
4
GND
5
SUSB
6
+5VSB
6
5
4
3
2
1
2.4.11 Internal Mouse/Keyboard Connector (MS1/KB1)
The board provides a keyboard (KB1) and Mouse (MS1) interface with
two 5-pin connectors.
16
Clock
1
Data
2
No Connection
3
GND
4
Power
5
Jumpers and Connectors
SBC81203 LGA775 SBC User’s Manual
CHAPTER 3
HARDWARE INSTALLATION
®
Before installing the processor, please access Intel website for more
detailed information http://www.intel.com .
3.1
Installing the Processor
The LGA775 processor socket comes with a cover to protect the
processor. Please install the processor into the CPU socket step by
step as below:
Hold the hook (A) of the lever and push it down.
Pull the lever (B) asisde to unlock the cover.
Hardware Installation
17
SBC81203 LGA775 SBC User’s Manual
Open the cover (C), you can
see the contact.
Be careful not to touch the
contact (D).
Remove the plastic cap (E) from the cover.
18
Hardware Installation
SBC81203 LGA775 SBC User’s Manual
Place the CPU down into the socket. Be careful not to touch the
contact.
Hold the edges of the CPU, and orientate it as the marked direction (G)
down into the socket to match the (H) and (F) locations.
Hardware Installation
19
SBC81203 LGA775 SBC User’s Manual
Slightly push down the cover and hook the lever (I~J). The CPU is
completely locked.
Orientate the CPU cooling fan to fixing holes on the board.
20
Hardware Installation
SBC81203 LGA775 SBC User’s Manual
Screw the CPU cooling fan onto the board.
Make sure the CPU fan is plugged to the CPU fan connector.
Hardware Installation
21
SBC81203 LGA775 SBC User’s Manual
3.2
Installing the Memory
The board supports two 240-pin DDR2 DIMM memory sockets with
maximum memory capacity up to 4GB.
Please follow steps below to install the memory modules:
1
2
Push down latches on each side of the DIMM socket.
Align the memory module with the socket that notches of
memory module must match the socket keys for a correct
intallation.
Install the memory module into the socket and push it firmly
down until it is fully seated. The socket latches are levered
upwards and clipped on to the edges of the DIMM.
Install any remaining DIMM modules.
3
4
22
Hardware Installation
SBC81203 LGA775 SBC User’s Manual
CHAPTER 4
HARDWARE DESCRIPTION
4.1
Microprocessors
®
TM
®
The SBC81203 Series supports Intel Core 2 Duo, Pentium D,
®
®
Pentium 4 and Celeron D processors, which make your system
®
operated under Windows 2000/XP and Linux environments. The
system performance depends on the microprocessor. Make sure you
install the microprocessor with all correct settings to prevent the CPU
from damages.
4.2
BIOS
The SBC81203 Series uses Award Plug and Play BIOS with a single
4Mbit Flash EPROM.
4.3
System Memory
The SBC81203 Series industrial CPU card supports two 240-pin DDR2
DIMM sockets for a maximum memory of 4GB DDR2 SDRAMs. The
memory module can come in sizes of 64MB, 128MB, 256MB, 512MB,
1GB and 2GB.
Hardware Description
23
SBC81203 LGA775 SBC User’s Manual
4.4
I/O Port Address Map
®
TM
®
®
®
The Intel Core 2 Duo, Pentium D, Pentium 4 and Celeron D
CPUs can communicate via I/O ports. There are total 1KB port
addresses available for assignment to other devices via I/O expansion
cards.
Address
000-01F
DMA controller #1
020-03F
Interrupt controller #1
040-05F
Timer
060-06F
Keyboard controller
070-07F
Real time clock, NMI
080-09F
DMA page register
0A0-0BF
Interrupt controller #2
0F0
0C0-0DF
0F1
0F8-0FF
24
Devices
Clear math coprocessor busy signal
DMA controller #2
Reset math coprocessor
Math processor
120
Disable watchdog timer operation (read)
121
Enable watchdog timer operation (read)
122
Watchdog
1F0-1F8
Fixed disk controller
200-207
Game port
300-31F
Prototype card
360-36F
Reserved
378-37F
Parallel port #1
3B0-3BF
MDA video card (including LPT1)
3C0-3CF
EGA card
3D0-3DF
CGA card
3F0-3F7
Floppy disk controller
3F8-3FF
Serial port #1 (COM1)
2F8-2FF
Serial port #2 (COM2)
Hardware Description
SBC81203 LGA775 SBC User’s Manual
CHAPTER 5
PHOENIX-AWARD BIOS UTILITY
The Phoenix-Award BIOS provides users with a built-in Setup program
to modify basic system configuration. All configured parameters are
stored in a battery-backed-up RAM (CMOS RAM) to save the Setup
information whenever the power is turned off.
5.1
Entering Setup
There are two ways to enter the Setup program. You may either turn
ON the computer and press <Del> immediately, or press the <Del>
and/or <Ctrl>, <Alt>, and <Esc> keys simultaneously when the
following message appears at the bottom of the screen during POST
(Power on Self Test).
TO ENTER SETUP PRESS DEL KEY
If the message disappears before you respond and you still want to
enter Setup, please restart the system to try it again. Turning the
system power OFF and ON, pressing the “RESET” button on the
system case or simultaneously pressing <Ctrl>, <Alt>, and <Del> keys
can restart the system. If you do not press keys at the right time and
the system doesn’t boot, an error message will pop out to prompt you
the following information:
PRESS <F1> TO CONTINUE, <CTRL-ALT-ESC> OR <DEL> TO ENTER SETUP
Phoenix-Award BIOS Utility
25
SBC81203 LGA775 SBC User’s Manual
5.2
Control Keys
Up arrow
Move cursor to the previous item
Down arrow
Move cursor to the next item
Left arrow
Move cursor to the item on the left hand
Right arrow
Move to the item in the right hand
Esc key
PgUp/“+” key
Main Menu -- Quit and delete changes into CMOS
Status Page Setup Menu and Option Page Setup
Menu -- Exit current page and return to Main Menu
Increase the numeric value or make changes
PgDn/“−“ key
Decrease the numeric value or make changes
F3 key
General help, only for Status Page Setup Menu and
Option Page Setup Menu
Change color from total 16 colors. F2 to select color
forward, (Shift) F2 to select color backward
Reserved
F4 key
Reserved
F1 key
(Shift) F2 key
F8 key
Restore the previous CMOS value from CMOS, only
for Option Page Setup Menu
Load the default CMOS value from BIOS default
table, only for Option Page Setup Menu
Load the Setup default, only for Option Page Setup
Menu
Reserved
F9 key
Reserved
F10 key
Save all the CMOS changes, only for Main Menu
F5 key
F6 key
F7 key
5.3
Getting Help
z
Main Menu
The online description of the highlighted setup function is displayed
at the bottom of the screen.
z
Status Page Setup Menu/Option Page Setup Menu
Press <F1> to pop out a small Help window that provides the
description of using appropriate keys and possible selections for
highlighted items. Press <F1> or <Esc> to exit the Help Window.
26
Phoenix-Award BIOS Utility
SBC81203 LGA775 SBC User’s Manual
5.4
The Main Menu
Once you enter the Award BIOS CMOS Setup Utility, the Main Menu
appears on the screen. In the Main Menu, there are several Setup
functions and a couple of Exit options for your selection. Use arrow
keys to select the Setup Page you intend to configure then press
<Enter> to accept or enter its sub-menu.
NOTE If your computer can not boot after making and saving
system changes with Setup, the Award BIOS will reset
your system to the CMOS default settings via its built-in
override feature.
It is strongly recommended that you should avoid changing the
chipset’s defaults. Both Award and your system manufacturer have
carefully set up these defaults that provide the best performance and
reliability.
Phoenix-Award BIOS Utility
27
SBC81203 LGA775 SBC User’s Manual
5.5
Standard CMOS Setup Menu
The Standard CMOS Setup Menu displays basic information about
your system. Use arrow keys to highlight each item, and use <PgUp>
or <PgDn> key to select the value you want in each item.
z
z
Date
The date format is <day>, <date> <month> <year>. Press <F3> to
show the calendar.
day
It is determined by the BIOS and read only, from Sunday
to Saturday.
date
It can be keyed with the numerical/ function key, from 1
to 31.
month
It is from January to December.
year
It shows the current year of BIOS.
Time
This item shows current time of your system with the format <hour>
<minute> <second>. The time is calculated based on the 24-hour
military-time clock. For example, 1 p.m. is 13:00:00.
28
Phoenix-Award BIOS Utility
SBC81203 LGA775 SBC User’s Manual
z
IDE Channel 0 Master/IDE Channel 0 Slave/IDE Channel 1
Master/IDE Channel 1 Slave
These items identify the types of each IDE channel installed in the
computer. There are 45 predefined types (Type 1 to Type 45) and
2 user’s definable types (Type User) for Enhanced IDE BIOS.
Press <PgUp>/<+> or <PgDn>/<−> to select a numbered hard disk
type, or directly type the number and press <Enter>. Please be
noted your drive’s specifications must match the drive table. The
hard disk will not work properly if you enter improper information. If
your hard disk drive type does not match or is not listed, you can
use Type User to manually define your own drive type.
If selecting Type User, you will be asked to enter related
information in the following items. Directly key in the information
and press <Enter>. This information should be provided in the
documentation from your hard disk vendor or the system
manufacturer.
If the HDD interface controller supports ESDI, select “Type 1”.
If the HDD interface controller supports SCSI, select “None”.
If the HDD interface controller supports CD-ROM, select “None”.
CYLS.
number of cylinders LANDZONE
landing zone
HEADS
number of heads
SECTORS
number of sectors
PRECOMP
write precom
MODE
HDD access mode
If there is no hard disk drive installed, select NONE and press
<Enter>.
z
Dive A type/Drive B type
This item identifies floppy disk type drive A or drive B installed in
the computer.
None
No floppy drive installed
360K, 3.5 in
3.5 inch PC-type standard drive; 360Kb Mini ITXcity
3.5 inch AT-type high-density drive; 1.2MB Mini
ITXcity
3.5 inch double-sided drive; 720Kb Mini ITXcity
3.5 inch double-sided drive; 1.44MB Mini ITXcity
3.5 inch double-sided drive; 2.88MB Mini ITXcity
1.2M, 3.5 in
720K, 3.5 in
1.44M, 3.5 in
2.88M, 3.5 in
Phoenix-Award BIOS Utility
29
SBC81203 LGA775 SBC User’s Manual
z
Halt On
This item determines whether the system will halt or not, if an error
is detected while powering up.
No errors
The system booting will halt on any errors detected.
(default)
All errors
Whenever BIOS detects a non-fatal error, the
system will stop and you will be prompted.
All, But
Keyboard
The system booting will not stop for a keyboard
error; it will stop for other errors.
All, But
Diskette
The system booting will not stop for a disk error; it
will stop for other errors.
All, But
Disk/Key
The system booting will not stop for a keyboard or
disk error; it will stop for other errors.
Press <Esc> to return to the Main Menu page.
30
Phoenix-Award BIOS Utility
SBC81203 LGA775 SBC User’s Manual
5.6
Advanced BIOS Features
This section allows you to configure and improve your system, to set up
some system features according to your preference.
z
CPU Feature
Scroll to this item and press <Enter> to view the CPU Feature sub
menu.
Phoenix-Award BIOS Utility
31
SBC81203 LGA775 SBC User’s Manual
z
Hard Disk Boot Priority
Scroll to this item and press <Enter> to view the sub menu to
decide the disk boot priority.
Press <Esc> to return to the Advanced BIOS Features page.
z
CD-ROM Boot Priority
Scroll to this item and press <Enter> to view the sub menu to
decide the CD-ROM boot priority.
Press <Esc> to return to the Advanced BIOS Features page.
32
Phoenix-Award BIOS Utility
SBC81203 LGA775 SBC User’s Manual
z
Virus Warning
This option flashes on the screen. During and after the system boot
up, any attempt to write to the boot sector or partition table of the
hard disk drive will halt the system with the following message. You
can run an anti-virus program to locate the problem. The default
setting is “Disabled”.
! WARNING !
Disk boot sector is to be modified
Type “Y” to accept write or “N” to abort write
Award Software, Inc.
Enabled
Disabled
NOTE:
z
z
It automatically activates while the system
boots up and a warning message
appears for an attempt to access the boot
sector or hard disk partition table.
No warning message will appear for
attempts to access the boot sector or
hard disk partition table.
This function is only available with DOS and other
operating systems that do not trap INT13.
CPU L1 & L2 Cache
These two options speed up memory access. However, it depends
on the CPU/chipset design. The default setting is “Enabled”. CPUs
without built-in internal cache will not provide the “CPU Internal
Cache” item on the menu.
Enabled
Enable cache
Disabled
Disable cache
Hyper-Threading Technology
Use this item to enable or disable Hyper-Threading Technology,
which makes a single physical processor perform multi-tasking
function as two logical ones.
z
Quick Power On Self Test
This option speeds up Power on Self Test (POST) after you turn on
the system power. If set as Enabled, BIOS will shorten or skip
some check items during POST. The default setting is “Enabled”.
Phoenix-Award BIOS Utility
33
SBC81203 LGA775 SBC User’s Manual
Enabled
Enable Quick POST
Disabled
Normal POST
z
First/Second/Third Boot Device
These items let you select the 1st, 2nd, and 3rd devices that the
system will search for during its boot-up sequence. The wide range
of selection includes Floppy, LS120, ZIP100, HDD0~3, SCSI, and
CDROM.
z
Boot Other Device
This item allows the user to enable or disable the boot device not
listed in the First/Second/Third boot devices option above. The
default setting is “Enabled”.
z
Swap Floppy Drive
This item allows you to determine whether to enable Swap Floppy
Drive or not. When enabled, the BIOS swap floppy drive
assignment makes Drive A become Drive B, and vice versa. The
default setting is “Disabled”.
z
Boot Up Floppy Seek
During POST, BIOS will determine the floppy disk drive type, 40 or
80 tracks. The 360Kb type is 40 tracks while 720Kb, 1.2MB and
1.44MB are all 80 tracks. The default value is “Enabled”.
Enabled
BIOS searches for floppy disk drive to determine if it is
40 or 80 tracks. Please be noted BIOS can not
differentiate 720K, 1.2M or 1.44M drive type as they all
are 80 tracks.
Disabled
BIOS will not search for the type of floppy disk drive by
track number. There will be no warning message
displayed if the installed drive is 360K.
z
Boot Up NumLock Status
Set the the Num Lock status when the system is powered on.
The default value is “On”.
z
Security Option
This item allows you to limit access to the system and Setup, or just
to Setup. The default value is “Setup”.
34
Phoenix-Award BIOS Utility
SBC81203 LGA775 SBC User’s Manual
System
If a wrong password is entered at the prompt, the system
will not boot, the access to Setup will be denied, either.
Setup
If a wrong password is entered at the prompt, the system
will boot, but the access to Setup will be denied.
NOTE
To disable the security, select PASSWORD
SETTING at Main Menu and then you will be
asked to enter a password. Do not type anything,
just press <Enter> and it will disable the security.
Once the security is disabled, the system will
boot and you can enter Setup freely.
z
APIC Mode
Use this item to enable or disable APIC (Advanced Programmable
Interrupt Controller) mode that provides symmetric multi-processing
(SMP) for systems.
z
MPS Version Control For OS
This item specifies the version of the Multiprocessor Specification
(MPS). Version 1.4 has extended configuration tables to improve
support for multiple PCI bus configurations and provide future
expandability.
z
OS Select For DRAM > 64MB
This item allows you to access the memory over 64MB in OS/2.
Press <Esc> to return to the Main Menu page.
Phoenix-Award BIOS Utility
35
SBC81203 LGA775 SBC User’s Manual
5.7
Advanced Chipset Features
This section contains completely optimized chipset’s features on the
board that you are strongly recommended to leave all items on this
page at their default values unless you are very familiar with the
technical specifications of your system hardware.
z
PCI Express Port 1 ~ 6
There are several PCI Express Ports for your selection.
z
PCI-E Compliancy Mode
This item allows you to set the version of the PCI Express base
specifications.
** VGA Setting **
z
PEG/Onchip VGA Control
Use this item to choose the primary display card.
z
On-Chip Frame Buffer Size
Use this item to set the VGA frame buffer size.
Press <Esc> to return to the Main Menu page.
36
Phoenix-Award BIOS Utility
SBC81203 LGA775 SBC User’s Manual
5.8
Integrated Peripherals
This section allows you to configure your SuperIO Device, IDE
Function and Onboard Device.
z
OnChip IDE Device
Scroll to this item and press <Enter> to view the sub menu OnChip
IDE Device.
¾
IDE HDD Block Mode
Block mode is also called block transfer, multiple commands,
or multiple sector read/write. If your IDE hard drive supports
block mode (most new drives do), select Enabled for
automatic detection of the optimal number of block
Phoenix-Award BIOS Utility
37
SBC81203 LGA775 SBC User’s Manual
¾
¾
¾
¾
read/writes per sector the drive can support.
IDE DMA transfer access
Automatic data transfer between system memory and IDE
device with minimum CPU intervention. This improves data
throughput and frees CPU to perform other tasks.
On-Chip Primary/Secondary PCI IDE
The integrated peripheral controller contains an IDE
interface with support for two IDE channels. Select Enabled
to activate each channel separately. The default value is
“Enabled”.
NOTE Choosing Disabled for these options will
automatically remove the IDE
rimaryMaster/Slave PIO and/or IDE Secondary
Master/Slave PIO items on the menu.
IDE Master/Slave PIO
The four IDE PIO (Programmed Input/Output) fields let you
set a PIO mode (0-4) for each of the four IDE devices that
the onboard IDE interface supports. Modes 0 to 4 provide
successively increased performance. In Auto mode, the
system automatically determines the best mode for each
device.
IDE Master/Slave UDMA
Select the mode of operation for the IDE drive. Ultra DMA33/66/100/133 implementation is possible only if your IDE
hard drive supports it and the operating environment
includes a DMA driver. If your hard drive and system
software both support Ultra DMA-33/66/100/133, select Auto
to enable UDMA mode by BIOS.
** On-Chip Serial ATA Setting **
z
On-Chip Serial ATA
Use this item to enable or disable the built-in on-chip serial ATA.
z
SATA PORT Speed Settings
Use this item to select SATA I or SATA II device support forcedly.
z
PATA IDE Mode
Use this item to set the PATA IDE mode. When set to Primary, P1
and P3 are Secondary; on the other hand, when set to Secondary,
P0 and P2 are Primary.
38
Phoenix-Award BIOS Utility
SBC81203 LGA775 SBC User’s Manual
z
SATA Port
If the “PATA IDE Mode“ is Primary, it will show ” P1, P3 is
Secondary” which means SATA 2 and SATA 4 are Secondary. If
the “PATA IDE Mode “ is Secondary, it will show “ P0, P2 is
Primary “ which means SATA 1 and SATA 3 are Primary.
Press <Esc> to return to the Integrated Peripherals page.
z
Onboard Device
Scroll to this item and press <Enter> to view the sub menu Onboard
Device.
¾
¾
¾
¾
USB Controller
Enable this item if you are using the USB in the system. You
should disable this item if a higher-level controller is added.
USB 2.0 Controller
Enable this item if you are using the EHCI (USB2.0)
controller in the system.
USB Keyboard Support
Enable this item if the system has a Universal Serial Bus
(USB) controller, and you have a USB keyboard.
AC’97 Audio
Use this item to enable or disable the onboard AC’97 Audio
function.
Press <Esc> to return to the Integrated Peripherals page.
Phoenix-Award BIOS Utility
39
SBC81203 LGA775 SBC User’s Manual
z
Super IO Device
Scroll to this item and press <Enter> to view the sub menu Super
IO Device.
¾
¾
¾
¾
¾
¾
40
Onboard FDC Controller
Select Enabled, if your system has a floppy disk controller
(FDC) installed on the system board and you want to use it.
If you install and-in FDC or the system has no floppy drive,
select Disabled in this field. Options: Enabled and Disabled.
Onboard Serial Port 1 / 2
Select an address and corresponding interrupt for the serial
port. Options: 3F8/IRQ4, 2E8/IRQ3, 3E8/IRQ4, 2F8/IRQ3,
Disabled, Auto.
Onboard Paralellel Port
This item allows you to determine the I/O address for
onboard parallel port. Options: 378H/IRQ7, 278H/IRQ5,
3BC/IRQ7 and Disabled.
Parallel Port Mode
Select an operating mode for the onboard parallel (printer)
port. Select Normal unless your hardware and software
require another mode in this field. Options: EPP1.9, ECP,
SPP, ECPEPP1.7, EPP1.7.
EPP Mode Select
Select EPP port type 1.7 or 1.9.
ECP Mode Use DMA
Select a DMA channel for the parallel port while using the
ECP mode.
Phoenix-Award BIOS Utility
SBC81203 LGA775 SBC User’s Manual
¾
PWRON After PWR-Fail
This item enables your computer to automatically restart or
return to its operating status.
Press <Esc> to return to the Integrated Peripherals page.
5.9
Power Management Setup
The Power Management Setup allows you to save energy of your
system effectively. It will shut down the hard disk and turn OFF video
display after a period of inactivity.
z
ACPI Function
This item allows you to enable/disable the Advanced Configuration
and Power Management (ACPI). The function is always “Enabled”.
z
ACPI Suspend Type
This item specifies the power saving modes for ACPI function. If
your operating system supports ACPI, such as Windows 98SE,
Windows ME and Windows 2000, you can choose to enter the
Standby mode in S1 (POS) or S3 (STR) fashion through the setting
of this field. Options are:
[S1 (POS)] The S1 sleep mode is a low power state. In this
state, no system context is lost (CPU or chipset) and
hardware maintains all system contexts.
[S3 (STR)] The S3 sleep mode is a lower power state where
the information of system configuration and open
Phoenix-Award BIOS Utility
41
SBC81203 LGA775 SBC User’s Manual
applications/files is saved to main memory that remains
powered while most other hardware components turn off to
save energy. The information stored in memory will be used
to restore the system when a “wake up” event occurs.
z
Power Management
This option allows you to select the type of power Management.
Options: APM, ACPI.
z
Video Off Method
This setting determines the manner in which the monitor is blanked.
z
V/H
SYNC+Blank
It turns OFF vertical and horizontal synchronization ports
and writes blanks to the video buffer.
DPMS
Select this option if your monitor supports the Display
Power Management Signaling (DPMS) standard of the
Video Electronics Standards Association (VESA). Use
the supplied software for your video subsystem to select
video power management values.
Blank Screen
The System only writes blanks to the video buffer.
Video Off In Suspend
This item defines if the video is powered down when the system is
put into suspend mode.
z
Suspend Type
If this item is set to the default Stop Grant, the CPU will go into Idle
Mode during power saving mode.
z
z
Suspend Mode
After the selected period of system inactivity (1 minute to 1 hour),
all devices except the CPU shut off. The default value is “Disabled”.
Disabled
System will never enter SUSPEND mode
1/2/4/6/8/10/2
0/30/40
Min/1 Hr
Defines the continuous idle time before the system
entering SUSPEND mode.
If any item defined in (J) is enabled & active,
SUSPEND timer will be reloaded
HDD Power Down
If HDD activity is not detected for the length of time specified in this
field, the hard disk drive will be powered down while all other
devices remain active.
42
Phoenix-Award BIOS Utility
SBC81203 LGA775 SBC User’s Manual
z
Soft-Off by PWR-BTTN
This option only works with systems using an ATX power supply. It
also allows users to define which type of soft power OFF sequence
the system will follow. The default value is “Instant-Off”.
Instant-Off
This option follows the conventional manner of system
performance when turning the power to OFF. InstantOff is a software power OFF sequence requiring the
power supply button is switched to OFF.
Delay 4 Sec.
Upon the system’s turning OFF through the power
switch, this option will delay the complete system power
OFF sequence approximately 4 seconds. Within this
delay period, the system will temporarily enter into the
Suspend Mode enabling you to restart the system at
once.
5.10 PnP/PCI Configuration Setup
This section describes the configuration of PCI (Personal Computer
Interconnect) bus system, which allows I/O devices to operate at
speeds close to the CPU speed while communicating with other
important components. This section covers very technical items that
only experienced users could change default settings.
z
PNP OS Installed
Select Yes if the system operating environment is Plug-and-Play
aware (e.g., Windows 95). The default value is “No”.
Phoenix-Award BIOS Utility
43
SBC81203 LGA775 SBC User’s Manual
z
Init Display First
This item allows you to decide whether PCI Slot or AGP to be the
first primary display card.
z
Reset Configuration Data
Normally, you leave this item Disabled. Select Enabled to reset
Extended System Configuration Data (ESCD) when you exit Setup
or if installing a new add-on cause the system reconfiguration a
serious conflict that the operating system can not boot. Options:
Enabled, Disabled.
z
Resources Controlled By
The Award Plug and Play BIOS can automatically configure all boot
and Plug and Play-compatible devices. If you select Auto, all
interrupt request (IRQ), DMA assignment, and Used DMA fields
disappear, as the BIOS automatically assigns them. The default
value is “Manual”.
z
IRQ Resources
When resources are controlled manually, assign each system
interrupt to one of the following types in accordance with the type of
devices using the interrupt:
1. Legacy ISA Devices compliant with the original PC AT bus
specification, requiring a specific interrupt (such as IRQ4 for serial port
1).
2. PCI/ISA PnP Devices compliant with the Plug and Play standard,
whether designed for PCI or ISA bus architecture.
The default value is “PCI/ISA PnP”.
z
PCI/VGA Palette Snoop
Some non-standard VGA display cards may not show colors
properly. This item allows you to set whether MPEG ISA/VESA
VGA Cards can work with PCI/VGA or not. When enabled, a
PCI/VGA can work with a MPEG ISA/VESA VGA card; when
disabled, a PCI/VGA cannot work with a MPEG ISA/VESA Card.
z
Rapid Card Boot First
This item helps you use additional PCI RAID card boot.
44
Phoenix-Award BIOS Utility
SBC81203 LGA775 SBC User’s Manual
** PCI Express relative items **
z
Maximum Payload Size
When using DDR SDRAM and Buffer size selection, another
consideration in designing a payload memory is the size of the
buffer for data storage. Maximum Payload Size defines the
maximum TLP (Transaction Layer Packet) data payload size for
the device.
5.11 PC Health Status
This section supports hardware monitering that lets you monitor those
parameters for critical voltages, temperatures and fan speed of the
board.
z
Current SYSTEM Temperature
Show you the current system1 temperature.
z
Current CPU Temperature
The current system CPU temperature will be automatically
detected by the system.
z
Current CPU FAN Speed
These optional and read-only items show current speeds in RPM
(Revolution Per Minute) for the CPU fan and chassis fan as
monitored by the hardware monitoring IC.
z
Current SYSTEM FAN1 Speed
Show you the current system fan1 temperature.
Phoenix-Award BIOS Utility
45
SBC81203 LGA775 SBC User’s Manual
z
Current SYSTEM FAN2 Speed
Show you the current system fan1 temperature.
z
Vcore +3.3V/+5V/+12V/VBAT(V)/5VSB
Show you the voltage of +3.3V/+5V/+12V.
5.12 Frequency/Voltage Control
This section is to control the CPU frequency and Supply Voltage, DIMM
OverVoltage and AGP voltage.
z
CPU Clock Ratio
Use this item to select the CPU’s frequency.
z
Auto Detect PCI Clk
The enabled item can automatically disable the clock source for a
PCI slot without a module, to reduce EMI (ElectroMagnetic
Interference).
z
Spread Spectrum
If spread spectrum is enabled, EMI (ElectroMagnetic Interference)
generated by the system can be significantly reduced.
46
Phoenix-Award BIOS Utility
SBC81203 LGA775 SBC User’s Manual
5.13 Load Optimized Defaults
This option allows you to load your system configuration with default
values. These default settings are optimized to enable high
performance features.
To load CMOS SRAM with SETUP default values, please enter “Y”. If
not, please enter “N”.
Phoenix-Award BIOS Utility
47
SBC81203 LGA775 SBC User’s Manual
5.14 Set Supervisor/User Password
You can set a supervisor or user password, or both of them. The
differences between them are:
1.
2.
Supervisor password: You can enter and change the options on
the setup menu.
User password: You can just enter, but have no right to change
the options on the setup menu.
When you select this function, the following message will appear at the
center of the screen to assist you in creating a password.
ENTER PASSWORD
Type a maximum eight-character password, and press <Enter>. This
typed password will clear previously entered password from the CMOS
memory. You will be asked to confirm this password. Type this
password again and press <Enter>. You may also press <Esc> to abort
this selection and not enter a password.
To disable the password, just press <Enter> when you are prompted to
enter a password. A message will confirm the password is getting
disabled. Once the password is disabled, the system will boot and you
can enter Setup freely.
PASSWORD DISABLED
When a password is enabled, you have to type it every time you enter
the Setup. It prevents any unauthorized persons from changing your
system configuration.
Additionally, when a password is enabled, you can also require the
BIOS to request a password every time the system reboots. This would
prevent unauthorized use of your computer.
You decide when the password is required for the BIOS Features
Setup Menu and its Security option. If the Security option is set to
“System”, the password is required during booting up and entry into the
Setup; if it is set as “Setup”, a prompt will only appear before entering
the Setup.
48
Phoenix-Award BIOS Utility
SBC81203 LGA775 SBC User’s Manual
5.15 Save & Exit Setup
This section allows you to determine whether or not to accept your
modifications. Type “Y” to quit the setup utility and save all changes
into the CMOS memory. Type “N” to bring you back to the Setup utility.
Phoenix-Award BIOS Utility
49
SBC81203 LGA775 SBC User’s Manual
5.16 Exit Without Saving
Select this option to exit the Setup utility without saving changes you
have made in this session. Type “Y”, and it will quit the Setup utility
without saving your modifications. Type “N” to return to the Setup utility.
50
Phoenix-Award BIOS Utility
SBC81203 LGA775 SBC User’s Manual
CHAPTER 6
INSTALLATION OF DRIVERS
The device drivers are located on the Product Information CD-ROM
that comes with the SBC81203 Series package. The auto-run
function of drivers will guide you to install the utilities and device
drivers under a Windows system. You can follow the onscreen
instructions to install these devices:
„ Chipset
„ VGA
„ LAN
„ Audio
6.1
Installing Chipset Driver
1. Run the SETUP.EXE program from the driver directory in
your driver CD. Click “Next” to next step.
Installation of Drivers
51
SBC81203 LGA775 SBC User’s Manual
®
2.
An Intel License Agreement appears to show you the
important information. Click “Yes” to next step.
3.
Please wait while running the following setup operations.
(3-1)
52
Instalation of Drivers
SBC81203 LGA775 SBC User’s Manual
(3-2)
4.
Click “Finish” to complete the setup process.
Installation of Drivers
53
SBC81203 LGA775 SBC User’s Manual
5.
6.2
You will be asked to reboot your computer when the
installation is completed. Please click “Yes, I want to restart
my computer now” if you don’t need to install any other
drivers. Otherwise, please click “No, I will restart my
computer later”, and go on next step.
Installing VGA Driver
1. Run the SETUP.EXE program from the driver directory in
your driver CD. Click “Next” to next step.
54
Instalation of Drivers
SBC81203 LGA775 SBC User’s Manual
®
2.
An Intel License Agreement appears to show you the
important information. Click “Yes” to next step.
3.
The message of Readme File Information appears to show
you the system requirements and installation information.
Please click “Next”.
Installation of Drivers
55
SBC81203 LGA775 SBC User’s Manual
4. Please wait while running the following setup operations.
5. When this message appears, please click “Next”.
56
Instalation of Drivers
SBC81203 LGA775 SBC User’s Manual
6. You will be asked to reboot your computer when the installation is
completed. Please click “Yes, I want to restart my computer now” if
you don’t need to install any other drivers. Otherwise, please click
“No, I will restart my computer later”, and click “Finish” to complete
the installation.
Installation of Drivers
57
SBC81203 LGA775 SBC User’s Manual
6.3
58
Installing LAN Driver
1.
Run the InstallShield Wizard for Ethernet from the driver
directory in your driver CD. Click “Next” to next step.
2.
Click “Install” to start the installation.
Instalation of Drivers
SBC81203 LGA775 SBC User’s Manual
3.
Please wait while running the following installation operation.
4.
Click “Finish” to complete the installation.
Installation of Drivers
59
SBC81203 LGA775 SBC User’s Manual
6.4
Installing Audio Driver
1. Run the InstallShield Wizard program from the driver directory
in your driver CD. Please wait while running the following
operation.
2. When this message appears, please click “Next”.
60
Instalation of Drivers
SBC81203 LGA775 SBC User’s Manual
3. You will be asked to reboot your computer when the
InstallShield Wizard is installed. Please click “Yes, I want to
restart my computer now” or “No, I will restart my computer
later”, and next click “Finish” to complete the installation.
Installation of Drivers
61
SBC81203 LGA775 SBC User’s Manual
MEMO
62
Instalation of Drivers
SBC81203 LGA775 SBC User’s Manual
APPENDIX A
WATCHDOG TIMER
Please follow the below WDT process for setup the WDT function.
Watchdog Timer
63
SBC81203 LGA775 SBC User’s Manual
MEMO
64
Watchdog Timer
SBC81203 LGA775 SBC User’s Manual
APPENDIX B
PCI IRQ ROUTING
Digital I/O Software Programming
PICMG PCI IRQ Routing
Device
ID
Slot
Int
PCI Slot 0
PCI Slot 1
PCI Slot 2
PCI Slot 3
31
30
29
28
0
1
2
3
BCDA
CDAB
DABC
ABCD
On Board Device IRQ Routing
Device
ID
Slot
PCI-ISA Bridge
22
4
Mini-PCI 1
26
5
PCI IRQ Routing
Int
CD
65
SBC81203 LGA775 SBC User’s Manual
MEMO
66
PCI IRQ Routing
SBC81203 LGA775 SBC User’s Manual
APPENDIX C
WHAT IS SATA RAID FUNCTION?
Introduction
ICH7R supports the SATA RAID function that allows you to combine
four SATA-II disk drives into RAID volume configurations. The RAID
configurations help you increase disk access speed (RAID0), or
withstand a single disk drive failure (RAID1 or RAID5) and thus protect
your data.
Main features of ICH8DO RAID functionalities are listed as follows:
1. RAID0 (Striping)
What Is SATA RAID Function
67
SBC81203 LGA775 SBC User’s Manual
2. RAID1 (Mirroring)
3. RAID5 (Block Interleaved Distributed Parity)
68
What Is SATA RAID Function
SBC81203 LGA775 SBC User’s Manual
APPENDIX D
MEMORY I/O ADDRESS
Memory I/O Address
69
SBC81203 LGA775 SBC User’s Manual
MEMO
70
Memory I/O Address
Download PDF

advertising