Kube II Scanner VeriPrint User Manual

Kube II Scanner VeriPrint User Manual
USER MANUAL
KUBE II
Scanner VeriPrint
CUSTOM S.p.A.
®
CUSTOM S.p.A.
Via Berettine 2/B
43010 Fontevivo (PARMA) - Italy
Tel. : +39 0521-680111
Fax : +39 0521-610701
http: www.custom.biz
Customer Service Department:
Email : [email protected]
© 2014 CUSTOM S.p.A. – Italy.
All rights reserved. Total or partial reproduction of this manual in whatever form,
whether by printed or electronic means,
is forbidden. While guaranteeing that the
information contained in it has been carefully checked, CUSTOM S.p.A. and other
entities utilized in the realization of this
manual bear no responsibility for how the
manual is used.
Information regarding any errors found in it
or suggestions on how it could be improved
are appreciated. Since products are subject to continuous check and improvement,
CUSTOM S.p.A. reserves the right to make
changes in information contained in this
manual without prior notii cation.
The pre-installed multimedia contents
are protected from Copyright CUSTOM
S.p.A. Other company and product names
mentioned herein may be trademarks of
their respective companies. Mention of
third-party products is for informational
purposes only and constitutes neither
an endorsement nor a recommendation.
CUSTOM S.p.A. assumes no responsibility
with regard to the performance or use of
these products.
THE IMAGES USED IN THIS MANUAL ARE USED AS AN ILLUSTRATIVE EXAMPLES. THEY COULDN’T
GENERAL SAFETY INFORMATION
Your attention is drawn to the following
actions that could compromise the characteristics of the product:
• Read and retain the instructions which
follow.
• Follow all indications and instructions
given on the device.
• Make sure that the surface on which
the device rests is stable. If it is not, the
device could fall, seriously damaging it.
• Make sure that the device rests on a hard
(non-padded) surface and that there is
sufi cient ventilation.
• When positioning the device, make sure
cables do not get damaged.
• Use the type of electrical power supply
indicated on the device label. If uncertain, contact your dealer.
• Make sure the electrical system that
supplies power to the device is equipped
with a ground wire and is protected by a
differential switch.
• Do not block the ventilation openings.
• Do not insert objects inside the device as
this could cause short-circuiting or damage components that could jeopardize
printer functioning.
• Do not carry out repairs on the device
yourself, except for the normal maintenance operations given in the user
manual.
• Make sure that there is an easily-accessible outlet with a capacity of no less
than 10A closely to where the device is
to be installed.
• Periodically perform scheduled maintenance on the device to avoid dirt build-up
that could compromise the correct, safe
operation of the unit.
• Before any type of work is done on the
machine, disconnect the power supply.
• Do not touch the head heating line with
bare hands or metal objects. Do not
perform any operation inside the printer
immediately after printing because the
head and motor tend to become very
hot.
REPRODUCE THE DESCRIBED
MODEL FAITHFULLY.
UNLESS OTHERWISE SPECIFIED,
THE INFORMATION GIVEN IN THIS
MANUAL
ARE REFERRED TO ALL MODELS
IN PRODUCTION AT THE ISSUE
DATE OF THIS DOCUMENT.
GENERAL INSTRUCTIONS
CUSTOM S.p.A. declines all responsibility for accidents or damage to persons or
property occurring as a result of tampering,
structural or functional modii cations, unsuitable or incorrect installations, environments not in keeping with the equipment’s
protection degree or with the required temperature and humidity conditions, failure
to carry out maintenance and periodical
inspections and poor repair work.
THE CE MARK AFFIXED TO
THE PRODUCT CERTIFY
THAT THE PRODUCT SATISFIES THE BASIC SAFETY
REQUIREMENTS.
The device is in conformity with the essential Electromagnetic Compatibility and
Electric Safety requirements laid down in
Directives 2006/95/CE and 2004/108/CE
inasmuch as it was designed in conformity
with the provisions laid down in the following Standards:
• EN 55022 Class B (Limits and methods
of measurements of radio disturbance
characteristics of Information Technology Equipment)
• EN 55024 (Information Technology
Equipment – Immunity characteristics –
Limits and methods of measurement)
• EN 60950-1 (Safety of information
equipment including electrical business
equipment)
GUIDELINES FOR
THE DISPOSAL OF
THE PRODUCT
The crossed-out rubbish bin logo means
that used electrical and electronic products
shall NOT be mixed with unsorted municipal waste. For more detailed information
about recycling of this product, refer to the
instructions of your country for the disposal
of these products.
• Do not dispose of this equipment as
miscellaneous solid municipal waste, but
arrange to have it collected separately.
• The re-use or correct recycling of the
electronic and electrical equipment
(EEE) is important in order to protect
the environment and the wellbeing of
humans.
• In accordance with European Directive
WEEE 2002/96/EC, special collection
points are available to which to deliver
waste electrical and electronic equipment and the equipment can also be
handed over to a distributor at the moment of purchasing a new equivalent
type.
• The public administration and producers
of electrical and electronic equipment
are involved in facilitating the processes
of the re-use and recovery of waste electrical and electronic equipment through
the organisation of collection activities
and the use of appropriate planning arrangements.
• Unauthorised disposal of waste electrical
and electronic equipment is punishable
by law with the appropriate penalties.
The format used for this manual improves use of natural resources reducing the quantity of necessary paper to print this
copy.
MANUAL
For details on the commands,
refer to the manual with code 77200000000400
TABLE OF CONTENTS
1
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.1 Document structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.2 Explanatory notes used in this manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2
DESCRIPTION
2.1
2.2
2.3
2.4
2.5
2.6 Box content . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Device components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Product label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Key functions: power up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Key functions: standby . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Status led lashes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3.1 Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
3.2 Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.3 Driver and SDK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
4
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
4.1
4.2
4.3
4.4
4.5
4.6
4.7
Opening the device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Inserting the card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Switch the device ON/OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Loading the paper roll . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Ticket reading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Ticket branding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
VeriPrint® system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
5
CONFIGURATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
5.1 5.2
5.3
5.4
5.5
5.6
5.7
5.8
Coniguration mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Setup report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Device status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Printer parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Ethernet parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Hexadecimal dump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Clock adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Scanner unit and VeriPrint® parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
7
6
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
6.1
6.2
6.3
6.4 Autocutter paper jam . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Planning of cleaning operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Upgrade irmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
7
SPECIFICATION
7.1 7.2 7.3
7.4
7.5
Hardware speciications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Character speciications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Device dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Power supply dimensions cod. 963GE020000003 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Character sets in CUSTOM/POS emulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
8
CONSUMABLES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
9 ACCESSORIES
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
9.1 Sides replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
10 TECHNICAL SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
11 ADVANCED FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
11.1
11.2
11.3
11.4
11.5
11.6
11.7
11.8
11.9
11.10
11.11
8
File sharing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Embedded Web Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Embedded Web Server: access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Embedded Web Server: functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Locator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Drivers installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Logos management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Fonts management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Printer setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
VeriPrint® setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Scanner unit setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
1
INTRODUCTION
1.1
Document structure
This document includes the following chapters:
1
INTRODUCTION
information about this document
2
DRIPTION
general dription of device
3
INSTALLATION
information required for a correct installation of the device
4
OPERATION
information required to make the device operative
5 CONFIGURATION dription of the coniguration parameters of the device
6
information for a correct periodic maintenance
MAINTENANCE
7 SPECIFICATION technical speciication for the device and its accessories
8
CONSUMABLES
dription and installation of the available consumables for the device
9
ACCESSORIES
dription and installation of the available accessories for the device
10 TECHNICAL SERVICE
information required for contacting the technical service
11 ADVANCED FUNCTIONS
information about special functions available with the device
1.2
Explanatory notes used in this manual
NOTE:
Gives important information or suggestions relative to the use of the device
ATTENTION:
Gives information that must be carefully followed to guard against damaging
the device
DANGER:
Gives information that must be carefully followed to guard against operator
injury or damage
9
10
2
DESCRIPTION
2.1
Box content
Remove the device from its carton being careful not to damage the packing material so that it may be re-used if the device
is to be transported in the future.
Make sure that all the components illustrated below are present and that there are no signs of damage. If there are, contact
Customer Service.
1. SD/MMC Card (see into
the slot)
1
2
3
4
5
6
2. AC adapter
3. USB cable
4. AC Power cable
5. Short guide
6. Device
• Open the device packaging.
• Remove the packing frame content and remove the packing frame.
• Take out the device.
• Keep the box, trays and packing materials in the event the device must be transported/shipped in the future.
11
2.2
Device components
External view
1. Paper compartment
1
2. Paper out (Printer)
2
3
3. Stacker
4
4. Opening lever (Printer)
5. Paper in (Scanner)
6. Opening key (Scanner)
5
6
7. Status led
8. FEED key
9. ON/OFF key
10. Paper out (Scanner)
11. USB potr
12. Ethernet port
13. RS232 serial port
14. Drawer port
15. Power supply port
7
8
9
10
11
12
12
13
14
15
Internal view
1. Sensor for paper detection in the printer unit
2. Sensor for cover open in the printer unit
3. VeriPrint® system over the printhead for the
image capturing
4. Sensor for scanner unit open
5. Sensor for paper detection in the scanner unit
6. Sensor for synchronization in the scanner unit
7. Sensor for detecting near paper end in the
printer unit
8. Temperature sensor for the printhead
1
8
2
3
4
5
6
7
13
2.3
Product label
PC = Product code (14 digits)
SN = Serial number
HW = Hardware release
XXXXXXXXXXXXXX
Rx
0000000000000000000
PC
SN
CT
DU
O EL
PR AB
L
14
HW
2.4
Key functions: power up
POWER UP
LF
ON/OFF
Hold
down
Fast
push
LF
Hold
down
printing
SETUP report
LF
ON/OFF
printing
FONT TEST
LF
Fast
push
ON/OFF
ON/OFF
LF
Fast
push
enter the SETUP MODE
for the printer parameters
LF
Fast
push
enter the SETUP MODE
for the printer clock
print the SETUP report
with Ethernet parameters
and enter the SETUP MODE
ON/OFF
Fast
push
modify
selected parameter
ON/OFF
LF
ON/OFF
Fast
push
next
parameter
15
2.5
Key functions: standby
STANDBY
LF
ON/OFF
Fast
push
Advance the paper
(preset length)
16
LF
ON/OFF
Fast
push
printing
demo ticket
2.6
Status led lashes
The Status led indicates hardware status of device. Given in the table below are the various led signals and the corresponding device status.
STATUS LED
DRIPTION
-
OFF
PRINTER OFF
GREEN
ON
PRINTER ON: NO ERROR
x1
RECEIVE DATA
x2
RECEPTION ERRORS
(PARITY, FRAME ERROR, OVERRUN ERROR)
x3
COMMAND NOT RECOGNIZED
x4
COMMAND RECEPTION TIME OUT
x5
NEAR PAPE END
x2
HEADING OVER TEMPERATURE
x3
PAPER END
x5
POWER SUPPLY VOLTAGE INCORRECT
x6
COVER OPEN
x3
RAM ERROR
x4
EEPROM ERROR
x5
CUTTER ERROR
GREEN
COMMUNICATION
STATUS
YELLOW
RECOVERABLE
ERROR
RED
UNRECOVERABLE
ERROR
17
18
3
INSTALLATION
3.1
Connections
The following igure shows the possible connections for the device.
ATTENTION:
In some using conditions, we recommend the installation of a ferrite core on the power supply cable.
USB
PC
Network
HUB
RS232
DK VIn 24Vdc
Power
Supply cable
(included)
ETHERNET
UTP
standard
cable
(pin-to-pin)
ETHERNET
CrossOver
standard
cable
PC
Barcode reader
ETH
PC
Barcode reader
Cash drawer
Power supply
19
3.2
Pinout
2
1
POWER SUPPLY
3
Tripolar female connector
4
1 +24 Vdc
2 GND
J10
3 GND
4 Frame GND
ATTENTION:
Respect power supply polarity.
NOTE:
Power supply cable
The following igure shows the connector pinout of the power supply cable for the device:
Tripolar male connector
n.c.
GND
Power supply cable
2
1
USB INTERFACE
Female USB type B connector
3
4
1 USB0-VBUS
J13
2 D0 -
(in/out)
3 D0 +
(in/out)
4 GND
SH1 SHIELD
SH2 SHIELD
20
(in)
+24 V
1
8
ETHERNET INTERFACE
Female RJ45 connector
1 RX+
2 RX3 TX+
4 n.c
J16
5 n.c
6 TX7 n.c
8 n.c
NOTES:
The functionality of two led are speciied in the following table:
LED
FUNCTION
LED-LNK
The led light (yellow color) on when a connection is active and lashes when occurs a data reception or transmission
LED-LAN
The led light (green color) on when occurs a 100Mbit connection and off when occurs a 10Mbit
connection
The printer automatically recognizes the type of connection (cross or pin-to-pin).
To directly connect the device to a Personal Computer, use a Cross-Over Ethernet cable.
To connect the device to a hub device, use an UTP Ethernet cable (Pin to Pin).
21
1
8
RS232 SERIAL INTERFACE
RJ45 female connector
1 RTS
When “1”, printer is ready to receive data
2 n.c.
3 DTR
When “1”, printer is fed
4 GND
J1
5 n.c.
6 RX
During reception, takes the values “0” and “1” depending on data.
7 TX
During transmission, takes the values “0” and “1” depending on data.
8 DTR
When “1”, printer is fed
NOTES:
Given the presence of the RS232 standard, logic value “0” corresponds to a voltage level of between +3Vdc and +15Vdc
and logic value “1” corresponds to a voltage level of between -3Vdc and -15Vdc.
8
7
6
5
4
3
2
1
DEVICE
22
DCD
DCD
RXD
TXD
TXD
RXD
GND
SIGNAL
DSR
DSR
CTS
CTS
1
2
3
4
5
6
7
8
9
DB9
RJ45
KUBEII SCANNER > PC connection
The following pictures shows an example of connections between the printer and a personal computer using the serial
connector:
PC
1
6
DRAWER CONNECTOR
Female RJ12 connector
1 GND
J7
2 SOL1
(out)
3 CASS
(in)
Drawer 1 command (open collector)
Drawer status
4 +24 Vdc
5 n.c.
6 GND
NOTES:
The solenoid of the drawer 1 must be connected from Pin 2 to Pin 4 on the drawer connector
PIN 4
PIN 2
DRAWER 1
(-)
RJ12
SOL
DEVICE
(+)
JACK
KUBE II SCANNER VERIPRINT > CASH DRAWER (optional) connection
Use an optional adapter cable RJ12-Jack to connect the device to a cash drawer. Refer to the picture below for the
connector pin signals
+24Vdc
CASH
DRAWER
23
3.3
Driver and SDK
The drivers are available for the following operating system:
OPERATING
SYSTEM
DESCRIPTION
INSTALLATION PROCEDURE
Driver for Windows XP
Driver for Windows VISTA (32/64bit)
Windows
Driver for Windows 7 (32/64bit)
From the START menu, press Run
and type-in the path where the SW
was saved on your PC, then click OK.
Follow the instructions that appear
on the screen to install the driver.
Driver for Windows 8 (32/64bit)
Driver for Windows 8.1 (32/64bit)
Linux
32/64bit
Follow the instruction get back on the
README.TXT ile. You can ind it in the
software package downloaded in advance.
NOTA:
All drivers can be found in the DOWNLOAD section of the web site www.custom.biz.
24
4
OPERATION
4.1
Opening the device
Printer cover
Scanner cover
Lift the opening levers and
open the printer cover.
Press the button on the front side and
push up the cover.
The indicator shows the state “Cover Open”
Lift the cover.
25
4.2
Inserting the card
1
Remove the carter on the printer side
using a screwdriver.
2
Contacts
facing down
Insert the card in the direction shown.
26
4.3
Switch the device ON/OFF
1
IN DC 24V
1A
Power supply cable
(supplied)
VIn 24Vdc
Connect the power adapter (supplied) to the device and the mains outlet.
Use the type of electrical power supply indicated on the label.
2
ON/OFF
Switch device On pressing key ON/OFF, the indicator light is switched on and the device is ready.
Switch device Off pressing key ON/OFF for at least 3 seconds.
27
4.4
Loading the paper roll
To change the paper proceed as follows. At every change of paper, check inside the device to locate and remove any
scraps of paper.
1
3
Open the device cover.
2
Close the device cover and wait until the paper is
loaded and automatically cut off.
Place the roll in the paper compartment and pull out the
paper for a few centimetres.
28
4.5
Ticket reading
The reading of the ticket is handled by command (refer to the manual with code 77200000000400). To read the ticket
proceed as follows.
1
2
TEXT TEXT
TEXT TEXT
TEXT TEXT
TEXT TEXT
TEXT TEXT
TEXT TEXT
TEXT TEXT
TEXT TEXT
OR
TEXT TEXT
TEXT TEXT
TEXT TEXT
TEXT TEXT
TEXT TEXT
TEXT TEXT
TEXT TEXT
TEXT TEXT
T
T E
T E
TE E
XT T
X
XT T
X
Wait the ticket reading.
Insert the ticket into the paper inlet of scanner,
in the direction shown in figure
(with the text facing the rear of the printer).
Retrieve the ticket from the paper outlet of scanner.
29
4.6
Ticket branding
The branding of the ticket is handled by command (refer to the manual with code 77200000000400). To brand the ticket
proceed as follows.
1
2
TEXT TEXT
TEXT TEXT
TEXT TEXT
TEXT TEXT
TEXT TEXT
TEXT TEXT
TEXT TEXT
TEXT TEXT
OR
TEXT TEXT
TEXT TEXT
TEXT TEXT
TEXT TEXT
TEXT TEXT
TEXT TEXT
TEXT TEXT
TEXT TEXT
T
T E
T E
TE E
XT T
X
XT T
X
Wait for the ticket branding.
BR
Insert the ticket into the paper inlet of scanner,
in the direction shown in figure
(with the text facing the rear of the printer).
30
D
N
A
Retrieve the ticket from the paper outlet of scanner.
4.7
VeriPrint® system
VeriPrint® is a system designed by CUSTOM S.p.A. thanks to which the functions of an image scanner and those of a
thermal printing head can be integrated in a single component to be included in systems and terminals for POS, betting/
lottery and ticketing application automation. Solutions and beneits with VeriPrint®.
• Automatic storing of the images of all tickets in a local or central database.
• Protection against manipulated tickets.
• In case of doubts on the originality of a ticket presented, possibility of retrieval
of the original image.
• Maximum safety, resulting in claim and cost reductions.
World patent for a system
allowing to print, scan and
check the data sent to the
printing process.
How VeriPrint® works
While printing a receipt, an integrated scanning element captures the image of the receipt automatically. The image is
stored or sent to a remote host in real time. The captured image represents the actual and “true” look of the receipt as the
customer receives it from the operator or a self-service kiosk.
JOURHRES = 300/200
JOURVRES = 300/200
(JOURNAL)
SD
/MMC CARD
SCANHRES = 600/300
SCANVRES = 400/200
LASTHRES = 300/200
LASTVRES = 300/200
VERIFY
LAST
SCAN
PRINT
31
Managing the contents
The VeriPrint ® printer is equipped with 3 storage units. When the printer is connected with the PC (using an USB cable)
this one detects the storage units as 3 removable disks:
FLASH DRV DISK
Is a lash type internal memory containing the conigurations iles for the printer (setup.ini), VeriPrint ® (scanner.cfg) and scanner unit (scanner_ext.cfg) (see chapter 12).
LAST SCAN DISK
Is a RAM type internal memory containing the image of the last printed ticket. The image ile is named according to the parameter set in scanner_ext.cfg ile (see chapter 12) and is overwritten every at any printing.
SD/MMC CARD DISK
Is an SD/MMC type external memory (supplied) containing the images of the printed tickets. The
images are organized by date using subfolders in YY/MM/GG format. Each image is saved in
bmp format and named as set in scanner.cfg ile
To use the VeriPrint ® system and manage the contents proceed as follow:
1
3
My Computer
Local disk (C:)
LASTSCANDRV
ON/OFF
<Lastfilename>.bmp
Switch the device ON
(see par. 4.3)
FLASHDRV
Scanner.cfg
Scanner_ext.cfg
2
Setup.ini
FLASHDRV
<date>
<Jourfilename>.bmp
<Jourfilename>.bmp
<Jourfilename>.bmp
<date>
<Jourfilename>.bmp
<Jourfilename>.bmp
PC
Connect the printer with PC
using an USB cable.
32
Wait for the device identification from PC.
At the first connection the PC require the printer driver
downloadable from our site: www.custom.biz.
5
CONFIGURATION
5.1
Coniguration mode
To enter the coniguration mode and print a SETUP report with the operating parameters of the device, proceed as follows.
1
3
KUBEII SCANNER
SCODE <code>
DCODE <code>
FCODE <code>
UCODE <code>
DCODE <code>
-
rel
rel
rel
rel
rel
1.00
1.00
1.00
1.00
1.00
PRINTER SETTINGS
PRINTER TYPE .........................................KUBE SCAN 84MM
PRINTING HEAD TYPE .............................SHEC T80
FEED
Press the FEED key.
The device prints the report with
parameters for printer settings.
2
4
FEED
FEED
ON/OFF
Enter
setup
Skip
setup
ON/OFF
While pressing the FEED key, switch on the
device by pressing the ON/OFF key.
Press the FEED key to enter the configuration mode
or press the ON/OFF key to skip setup procedure.
33
5.2
Setup report
The following igures show the setup reports of the device. The shown values for parameters are sample values; for the list and the dription of device and Ethernet parameters see the following paragraphs.
DEVICE NAME and
FIRMWARE MODULES
RELEASE
KUBEII SCANNER
SCODE <code>
BCODE <code>
FCODE <code>
UCODE <code>
DCODE <code>
-
rel
rel
rel
rel
rel
1.00
1.00
1.00
1.00
1.00
PRINTER SETTINGS
DEVICE
STATUS
PRINTER
PARAMETERS
KEYS FUNCTIONS
34
PRINTER TYPE ....................................KUBE SCAN 84
PRINTING HEAD TYPE ........................SHEC T80
ETHERNET TYPE.................................10/100Base-TX
PROGRAM MEMORY TEST.................OK
DYNAMIC RAM TEST...........................OK
FPGA TEST...........................................OK
EEPROM TEST.....................................OK
CUTTER TEST......................................OK
HEAD VOLTAGE
[V] = 23,37
HEAD TEMPERATURE
[°C] = 25
POWER ON COUNTER
= 4
PAPER PRINTED
[cm] = 40
CUT COUNTER
= 1
DATE - TIME
= 01/01/2014 12:00
RS232 Baud Rate ........................... :
RS232 Data Length ......................... :
RS232 Parity ................................... :
RS232 Handshaking ....................... :
Busy Condition ................................ :
USB Address Number ..................... :
USB Interface 2 ............................... :
Print Mode ....................................... :
Autofeed .......................................... :
Chars / inch ..................................... :
Speed / Quality................................ :
Paper Width..................................... :
Total cut (ESC i) .............................. :
PaperEnd Buffer Clear .................... :
PowerFail WakeUp Mode................ :
Print Density.................................... :
[ LF ]
enter setup
[ ON/OFF ]
skip Setup
115200 bps
8 bits/chr
None
Hardware
RxFull
0
Mass Storage
Normal
CR Disabled
A=15 B=20 cpi
High Speed
82mm
Enabled
Enabled
LAST PWR State
0%
KEYS FUNCTIONS
ETHERNET PARAMETERS
[ LF ]
enter Printer setup
[ ON/OFF ]
enter Ethernet Setup
[ LF + ON/OFF] skip Setup
DHCP Client ............................... :
FTP Server ................................. :
Disabled
Disabled
IP Address .................................. :
Subnet Mask .............................. :
Default Gateway......................... :
192.168. 0. 1
255.255.240. 0
192.168. 0. 5
MAC Address ............................. :
00-0E-E2-02-0B-0D
For advanced printer setup please connect to the site
http://192.168.0.1
5.3
Device status
The device operating status is indicated in the coniguration print-out in which, next to the name of the components displayed, the following information is given:
PRINTER TYPE
device model
PRINTING HEAD TYPE
print head model
ETHERNET TYPE
communication speed
PROGRAM MEMORY TEST
OK appears if functioning and NOT OK if faulty
DYNAMIC RAM TEST
OK appears if functioning and NOT OK if faulty
FPGA TEST
OK appears if functioning and NOT OK if faulty
EEPROM TEST
OK appears if functioning and NOT OK if faulty
CUTTER TEST
OK appears if functioning and NOT OK if faulty
HEAD VOLTAGE
voltage of the head
HEAD TEMPERATURE
temperature of the head
POWER ON COUNTER
number of power-ups made
PAPER PRINTED
centimetres of paper printed
CUT COUNTER
number of cuts performed
DATE - TIME
current date and time
35
5.4
Printer parameters
This device allows the coniguration of the parameters listed in the following table.
The parameters marked with the symbol D are the default values.
Settings remain active even after the device has been turned off and they are stored in non-volatile memory.
RS232 BAUD RATE
Communication speed of the serial interface:
115200 D
57600
38400
19200
9600
4800
2400
1200
NOTE: Parameter valid only with serial interface.
RS232 DATA LENGTH
Number of bit used for characters encoding:
7 bits/car
8 bits/car D
NOTE: Parameter valid only with serial interface.
RS232 PARITY
Bit for the parity control of the serial interface:
None D = parity bit omitted
Even = even value for parity bit
Odd =
odd value for parity bit
NOTE: Parameter valid only with serial interface.
RS232 HANDSHAKING
Handshaking:
XON/XOFF =
Hardware D =
software handshaking
hardware handshaking (CTS/RTS)
NOTES:
Parameter valid only with serial interface.
When the receive buffer is full, if handshaking is set to XON/XOFF, the device sends the XOFF (0x13) on the
serial port. When the receive buffer has cleared once again, if handshaking is set to XON/XOFF, the device
sends the XON (0x11) on the serial port.
BUSY CONDITION
Activation mode for Busy signal:
OffLine/ RXFull = Busy signal is activated when the device is both in OffLine status and
the buffer is full
RXFull D =
Busy signal is activated when the buffer is full
NOTE: Parameter valid only with serial interface.
36
USB MASS STORAGE
Sharing mode from Mass Storage:
Disabled D = sharing mode disabled
Enabled =
sharing mode enabled
USB ADDRESS NUMBER
Numerical address code for the univocal identiication of the USB device (in case of more
than a USB device connected with the same PC):
0D
1
USB INTERFACE 2
2
3
4
5
6
7
8
9
Sharing mode of the detected image (connect a PC via USB):
Disabled =
Enabled =
sharing mode disabled
after scanning, the BMP image of the ticket is sent to the PC through
the USB port.
Mass Storage D = the printer is detected by the PC as a logic disk.
After scanning, the BMP image of the ticket is stored into the “LAST
SCAN” drive together with a txt ile. browse the logical disk from your
PC.
PRINT MODE
Printing mode:
Normal D = enables printing in normal writing way
Reverse = enables printing rotated 180 degrees
AUTOFEED
Setting of the Carriage Return character:
CR disabled D = Carriage Return disabled
CR enabled = Carriage Return enabled
NOTE: The parameter is printed only with CUSTOM/POS emulation enabled.
CHARS / INCH
Font selection:
A = 11 cpi, B = 15 cpi
A = 15 cpi, B = 20 cpi D
NOTES:
CPI = Characters Per Inch
SPEED / QUALITY
Setting of printing speed and printing quality:
Normal
High Quality
High Speed D
PAPER WIDTH
Width of printing area:
72mm (70mm width)
74mm (72mm width)
76mm (74mm width)
78mm (76mm width)
80mm (78mm width)
82mm D (80mm width)
37
TOTAL CUT
Sets the behavior of the cutter when the total cut command 0x1B 0x69 ( i) is sent:
Disabled =
The total cut command 0x1B 0x69 ( i) will be ignored and the device executes
a partial cut
Enabled D = The total cut command 0x1B 0x69 ( i) will be executed.
PAPEREND BUFFER
CLEAR
Cleaning mode of the data in receive buffer, if the printing is stopped due to lack of paper:
Disabled =
The data remain in the receive buffer. When the paper runs out, the device
keeps the remaining data in the receive buffer and prints the remaining
portion of the ticket after that the new paper is loaded.
Enabled D = When the paper runs out, all data in the receive buffer are deleted.
POWERFAIL
WAKEUP MODE
This parameter set the printer state (ON or OFF) that will be automatically restored after
a power fail:
LAST PWR State D = the printer returns in the previous state (ON or OFF) before the
power fail.
Always ON =
the printer always switches on automatically, after a power fail.
Always OFF = D
the printer switches on only by pressing the ON/OFF key after a
power fail.
PRINT DENSITY
Adjusting the printing density:
-50%
-37%
-25%
38
-12%
0D
+12%
+25%
+37%
+50%
5.5
Ethernet parameters
This device allows the coniguration of the parameters listed in the following table.
The parameters marked with the symbol D are the default values.
Settings remain active even after the device has been turned off.
DHCP CLIENT
Setting of the DHCP protocol:
Disabled D = protocol disabled
Enabled =
protocol enabled
FTP SERVER
Setting of the FTP server:
Disabled D = server disabled
Enabled =
server enabled
IP ADDRESS
IP address of device; this parameter is assigned by the network administrator.
NOTE: Press the FEED key to modify the value of the highlighted digit.
Pressing ON/OFF key to move the cursor on the next digit (if the cursor is on the latest digit, proceed to next
parameter by pressing the ON/OFF key).
SUBNET MASK
IP address of device; this parameter is assigned by the network administrator.
NOTE: Press the FEED key to modify the value of the highlighted digit.
Pressing ON/OFF key to move the cursor on the next digit (if the cursor is on the latest digit, proceed to next
parameter by pressing the ON/OFF key).
DEFAULT GATEWAY
This parameter identiies the Gateway IP address used to send applications to the external
network.
NOTE: Press the FEED key to modify the value of the highlighted digit.
Pressing ON/OFF key to move the cursor on the next digit (if the cursor is on the latest digit, proceed to next
parameter by pressing the ON/OFF key).
MAC ADDRESS
This is the number, provided by the constructor, that identiies the device; this number is
univocal.
NOTE: This parameter can’t be modiied by set up.
ATTENTION:
Any changes to network parameters will interrupt browser connection. If the server not responding you must reconnect
to the new IP address set.
39
5.6
Hexadecimal dump
This function is used for the diagnosis of the characters received from the communications port. Characters are printed as
hexadecimal code and the corresponding ASCII code (see below). Each line is preceded by a counter in hexadecimal that
indicates the number of bytes received.
During the startup, if you hold down the FEED key, the printer enters the self-test routine and print the setup report.
The printer remains in standby until a key is pressed or characters are received through the communication port (Hexadecimal Dump mode). For each character sent, the ticket shows the hexadecimal value and the ASCII codes (if the characters
are underlined, the receive buffer is full). Shown below is an example of a Hexadecimal Dump:
HEXADECIMAL DUMP
31
39
37
68
73
66
65
6F
6F
77
72
6B
64
73
66
6A
40
32
30
38
6B
64
73
69
72
75
65
69
6C
66
64
6B
6B
33
31
39
6A
66
64
6F
69
77
72
6F
73
6B
66
F2
6C
34
32
75
73
6B
66
79
75
65
69
75
64
73
6B
6A
68
35
33
69
64
6A
6B
75
77
72
6F
77
66
64
6A
73
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
12345 ...
90123 ...
789ui ...
hkjsd ...
sdfkj ...
fsdfk ...
eioyu ...
oriuw ...
ouwer ...
werio ...
riouw ...
klsdf ...
dfksd ...
sdfkj ...
fk≥j ...
jklh
5.7
Clock adjustment
To adjust the clock, proceed as follows.
1
3
0 1 2 3 4 5 6 7 8 9
LF
Enter
setup
CLOCK SETUP
[LF] to modify date/time
[ON/OFF] to next field
Enter the setup mode following
the instructions in par. 5.1.
2
00/00/00
00:00:00
0
20/00/00
00:00:00
2
ON/OFF
FEED
ON/OFF
Press the FEED and ON/OFF to enter
the setup mode for printer clock.
Follow the instructions printed on the paper
for the key functionality. The highlighted digit
(the number is written in negative mode) indicates
the digit to be modified. Pressing FEED key
to modify the value of the highlighted digit;
every single FEED key pressure increases
of 1 his value. Once the value 9 is reached
the counting starts again from 0. Pressing
ON/OFF key to move the cursor on the next digit.
41
5.8
Scanner unit and VeriPrint® parameters
To set the operating parameters for the scanner unit and the VeriPrint® system, see Par. 11.10 and 11.11.
42
6
MAINTENANCE
6.1
Autocutter paper jam
1
3
FEED
FEED
Press the FEED key.
4
Press the FEED key to try to unlock the cutter.
If the cutter did not unlock press slightly the left side
of the cutter cover, so that it opens.
2
Rotate the mechanism in the direction that oppose
less resistance, as shown in the label.
If the problem persists, please
contact the customer service.
Reassemble the cover removed previously.
43
6.2
Planning of cleaning operations
The regular cleaning of the device keeps the print quality and extends its life. The following table shows the recommended
planning for the cleaning operations.
EVERY PAPER CHANGE
Printhead and scanner ‘VeriPrint’
Use isopropyl alcohol
Rollers
Use isopropyl alcohol
EVERY 5 PAPER CHANGES
Cutter
Paper path
Sensors
Use compressed air
Use compressed air or tweezers
Use compressed air
EVERY 6 MONTHS OR AS NEEDED
Printer case
Use compressed air or a soft cloth
AT ANY DECREASE IN PRINT QUALITY
Printhead for branding (scanner unit)
Use isopropyl alcohol
For speciic procedures, see the following pages.
NOTE:
If you use the device in dusty environments, you must reduce the intervals between the cleaning operations.
44
6.3
Cleaning
For periodic cleaning of the device, see the instructions below
Sensors
1
Disconnect the power supply cable and
open the device cover (see par. 4.1)
2
Clean the device sensors
by using compressed air.
ATTENTION:
Do not use alcohol, solvents, or hard brushes.
Do not let water or other liquids get inside the machine.
Alcohol, solvent
ON
45
Paper path
Printhead and scanner ‘VeriPrint’
1
1
Disconnect the power supply cable and
open the device cover (see par. 4.1)
Disconnect the power supply cable and
open the device cover (see par. 4.1)
2
2
ISOPROPYL ALCOHOL
Ve
riP
Pri rint®
nth
ead
Clean the area involved in the passage of paper
by using compressed air.
ATTENTION:
Do not use solvents, or hard brushes.
Do not let water or other liquids get inside the machine.
ATTENTION:
Do not use alcohol, solvents, or hard brushes.
Do not let water or other liquids get inside the machine.
Alcohol, solvent
46
Clean the printing head and the scanner unit by using
a non-abrasive cloth moistened with isopropyl.
ON
ON
Printhead for branding (scanner unit)
Printing roller
1
1
Disconnect the power supply cable and
open the scanner cover (see par. 4.1)
2
Disconnect the power supply cable and
open the device cover (see par. 4.1)
2
ISOPROPYL ALCOHOL
ISOPROPYL ALCOHOL
Clean the printing head by using
a non-abrasive cloth moistened with isopropyl.
ATTENTION:
Do not use solvents, or hard brushes.
Do not let water or other liquids get inside the machine.
ON
Disconnect the power supply cable and
open the device cover (see par. 4.1)
ATTENTION:
Do not use solvents, or hard brushes.
Do not let water or other liquids get inside the machine.
ON
47
Cutter
1
3
Disconnect the power supply cable and
open the device cover (see par. 4.1)
2
Press slightly the left side
of the cutter cover, so that it opens.
4
Clean the cutter compartment from the inside
using compressed air.
ATTENTION:
Do not use alcohol, solvents, or hard brushes.
Do not let water or other liquids get inside the machine.
Alcohol, solvent
48
ON
Clean the cutter compartment
using compressed air.
Case
1
5
Disconnect the power supply cable
2
Reassemble the cover removed previously.
To clean the device,
use compressed air or a soft cloth.
ATTENTION:
Do not use alcohol, solvents, or hard brushes.
Do not let water or other liquids get inside the machine.
Alcohol, solvent
ON
49
6.4
Upgrade irmware
9. Select the serial communication port (ex. COM1):
WARNING: During communication between PC/device
for the irmware update it is strictly forbidden to disconnect the communication cable or to remove the power
supply of the devices not to endanger the proper functioning of the device.
NOTES:
The latest irmware of the device is available in the download area of the web site www.custom.biz
C:\KUBEIISCANNER.PSW
Install on the PC used for device upgrading the UPGCEPRN software available in the download area of the
web site www.custom.biz.
UPDATE VIA SERIAL INTERFACE
Proceed as follows:
1. Write down the product code (14 digits) printed on the
product label (see par. 2.3).
2. Go to the web site www.custom.biz and download the
appropriate irmware release from the DOWNLOAD area.
3. Print the SETUP report (see chapter 5).
4. Switch OFF the device.
5. Connect the device to the PC using a serial cable (see
paragraph 3.1).
6. Switch ON the device.
7. Launch the software UPGCEPRN.
8. Select the update ile .PSW location:
10. Detecting and setting of the parameters necessary for
serial communication are performed automatically and
then updating begins.
11. After a few minutes a message on the screen warns
that the update is completed.
12. Print a new SETUP report to verify the new irmware release (see chapter 5).
50
UPDATE VIA USB INTERFACE
Custom KUBEIISCANNER
ATTENTION:
Only during the irmware update, the connection between PC and device must be direct, without the use
of wireless HUB.
Only during the irmware update, do not connect or disconnect other USB devices.
Custom KUBEIISCANNER
NOTE: For communication via USB you must install on
PC the device driver available in the download area of
the web site www.custom.biz.
Proceed as follows:
1. Write down the product code (14 digits) printed on the
product label (see par. 2.3).
C:\KUBEIISCANNER.PSW
2. Go to the web site www.custom.biz and download the
appropriate irmware release from the DOWNLOAD area.
3. Print the SETUP report (see chapter 5).
4. Switch OFF the device.
5. Connect the device to the PC using a USB cable (see
paragraph 3.1).
6. Switch ON the device.
7. Launch the software UPGCEPRN.
8. Select the update ile .PSW location:
10. After a few minutes a message on the screen warns
that the update is completed.
11. Print a new SETUP report to verify the new irmware release (see chapter 5).
9. Select item USB and then select the USB device among
those proposed (eg. KUBEIISCANNER):
51
52
7
SPECIFICATION
7.1
Hardware speciications
GENERALS
Sensors
Paper presence, head temperature,
cover open, near paper end
MTBF (1)
78 340 hours
Emulations
Printing driver
CUSTOM/POS
Windows XP
VISTA (32/64bit)
Windows 7 (32/64bit)
Windows 8 (32/64bit)
Windows 8.1 (32/64bit)
Linux
INTERFACES
USB Port
480 Mbit/sec (USB 2.0 high speed)
RS232 serial port
from 1200 to 115200 bps
ETHERNET Port
10 Mbit/sec, 100 Mbit/sec
MEMORIES
Receive buffer
20 Kbytes
Flash memory
32 Mbytes
RAM memory
32 Mbytes
LASTSCAN memory
Graphic memory
Memory Card SD/MMC
9 Mbytes
Logos dynamic management (max 2MB graphics memory)
max 2 Gbytes
PRINTER SPECIFICATIONS
Resolution
203 DPI (8 dot/mm)
Printing method
Thermal, ixed head
53
Head life (2)
100 Km / 100M pulses
Printing width
72, 74, 76, 78, 80, 82mm
Printing mode
Normal, 90°, 180°, 270°
Printing format
Height/Width from 1 to 8,
bold, reverse,
underlined, italic
Character fonts
Printable barcode
Printing speed (2) (4)
PC437, PC850, PC860, PC863, PC865, PC858 (euro),
2 TrueType fonts (3)
UPCA, UPCE, EAN13, EAN8,
CODE39, ITF, CODABAR, CODE93,
CODE128, CODE32, PDF417,
DATAMATRIX, AZTEC, QRCODE
High quality = 95 mm/sec
Normal = 150 mm/sec
High speed = 190 mm/sec
PAPER
Type of paper
Paper width
Paper weight
Paper thickness
Thermal rolls, heat-sensitive side on outside of roll
82.5 ± 0.5 mm
from 70 g/m2 to 80 g/m2
from 75μm to 85μm
Recommended paper
KANZAN KP460
MITSUBISHI TL4000, TL1000
External roll diameter
max 150 mm
External roll core diameter
40mm
Paper end
Not attached to roll core
Core type
Cardboard or plastic
CUTTER
Paper cut
Estimated life (2)
54
Total
> 1 000 000 cuts
VERIPRINT® SYSTEM
Scanning width
84mm
400, 200 dpi (Vertical)
600, 300 dpi (Horizontal)
Scanning resolution
Files format
BMP (256, 16, 2 gray tones)
400, 300, 200 dpi (Vertical)
600, 300, 200 dpi (Horizontal)
Saving resolution
SCANNER UNIT
Scanning speed
250mm/sec
Scanning area
Output format
82mm (W) x 350mm (L) max
256 gray scale and b/w image, dot matrix (x,y)
Scanning resolution
Tickets Layout
Rectangles research
203 DPI (8 dot/mm)
max 40
8800 max (total)
PRINTER ELECTRICAL SPECIFICATIONS
Power supply
Medium consumption (4)
Stand-by consumption
24 Vdc ±10% (external power supply)
1A
0.14 A
ELECTRICAL SPECIFICATIONS POWER SUPPLY cod.963GE020000003
Power supply voltage
Frequency
from 100 Vac to 240 Vac
from 50 Hz to 60 Hz
Current (output)
2.5 A
Power
60W
ENVIRONMENTAL CONDITIONS
Operating temperature
from 0°C to +40°C
55
Relative humidity
Storage temperature
Storage relative humidity
from 10% Rh to 85% Rh
from -20 °C to +70 °C
from 10% Rh to 90% Rh
NOTES:
(1) : Electronic board.
(2) : Respecting the regular schedule of cleaning for the device components.
(3) : “Veramono.ttf” and “Vera.ttf” are installed on device lash disk. It is possible to install additional TrueType fonts (see par.11.8).
(4) : Referred to a standard CUSTOM receipt (L=10cm, Density = 12,5% dots on).
56
7.2
Character speciications
Character set
Character density
Number of columns
Character / sec
Lines / sec
Characters (L x H mm)-Normal
3
11 cpi
15 cpi
20 cpi
35
45
64
2250
2895
4050
63
63
63
2,25x3
1,75 x 3
1,25 x 3
NOTE: Theoretical values.
57
7.3
Device dimensions
Length
357 mm (with cover closed)
445 mm (with cover open)
Height
216 mm (with cover closed)
345 mm (with cover open)
Width
140 mm
Weight
2535 g
NOTE:
Dimensions referred to devices without paper roll.
All the dimensions shown in following igures are in millimetres.
357
90
152
206
216
267
58
94
127
140
7.4
Power supply dimensions cod. 963GE020000003
Length
127 mm
Height
35,5 mm
Width
56 mm
35,5
All the dimensions shown in following igures are in millimetres.
AC INLET
56
N.C
2 1
3
GND
+24V
127
DC OUTPUT WIRE
59
7.5
Character sets in CUSTOM/POS emulation
The printer has 3 fonts of varying width (11, 15 and 20 cpi) which may be accessed through programming or control characters.
Each of these fonts offers the following code tables: PC437, PC850, PC860, PC863, PC865, PC858.
PC437 CODE TABLE (Usa, Standard Europe)
60
Char
SP
!
“
#
$
%
&
‘
(
)
*
+
,
-
.
/
Hex
0020
0021
0022
0023
0024
0025
0026
0027
0028
0029
002A
002B
002C
002D
002E
002F
Dec
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
Char
0
1
2
3
4
5
6
7
8
9
:
;
<
=
>
?
Hex
0030
0031
0032
0033
0034
0035
0036
0037
0038
0039
003A
003B
003C
003D
003E
003F
Dec
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
Char
@
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
Hex
0040
0041
0042
0043
0044
0045
0046
0047
0048
0049
004A
004B
004C
004D
004E
004F
Dec
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
Char
P
Q
R
S
T
U
V
W
X
Y
Z
[
\
]
^
_
Hex
0050
0051
0052
0053
0054
0055
0056
0057
0058
0059
005A
005B
005C
005D
005E
005F
Dec
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
Char
`
a
b
c
d
e
f
g
h
i
j
k
l
m
n
o
Hex
0060
0061
0062
0063
0064
0065
0066
0067
0068
0069
006A
006B
006C
006D
006E
006F
Dec
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
Char
p
q
r
s
t
u
v
w
x
y
z
{
|
}
~
⌂
Hex
0070
0071
0072
0073
0074
0075
0076
0077
0078
0079
007A
007B
007C
007D
007E
007F
Dec
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
Char
Ç
ü
é
â
ä
à
å
ç
ê
ë
è
ï
î
ì
Ä
Å
Hex
0080
0081
0082
0083
0084
0085
0086
0087
0088
0089
008A
008B
008C
008D
008E
008F
Dec
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
Char
É
æ
Æ
ô
ö
ò
û
ù
ÿ
Ö
Ü
¢
£
¥
₧
ƒ
Hex
0090
0091
0092
0093
0094
0095
0096
0097
0098
0099
009A
009B
009C
009D
009E
009F
Dec
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
Char
á
í
ó
ú
ñ
Ñ
ª
º
¿
⌐
¬
½
¼
¡
«
»
Hex
00A0
00A1
00A2
00A3
00A4
00A5
00A6
00A7
00A8
00A9
00AA
00AB
00AC
00AD
00AE
00AF
Dec
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
Char
░
▒
▓
│
┤
╡
╢
╖
╕
╣
║
╗
╝
╜
╛
┐
Hex
00B0
00B1
00B2
00B3
00B4
00B5
00B6
00B7
00B8
00B9
00BA
00BB
00BC
00BD
00BE
00BF
Dec
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
Char
└
┴
┬
├
─
┼
╞
╟
╚
╔
╩
╦
╠
═
╬
╧
Hex
00C0
00C1
00C2
00C3
00C4
00C5
00C6
00C7
00C8
00C9
00CA
00CB
00CC
00CD
00CE
00CF
Dec
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
Char
╨
╤
╥
╙
╘
╒
╓
╫
╪
┘
┌
█
▄
▌
▐
▀
Hex
00D0
00D1
00D2
00D3
00D4
00D5
00D6
00D7
00D8
00D9
00DA
00DB
00DC
00DD
00DE
00DF
Dec
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
Char
α
ß
Γ
π
Σ
σ
µ
τ
Φ
Θ
Ω
δ
∞
φ
ε
∩
Hex
00E0
00E1
00E2
00E3
00E4
00E5
00E6
00E7
00E8
00E9
00EA
00EB
00EC
00ED
00EE
00EF
Dec
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
Char
≡
±
≥
≤
⌠
⌡
÷
≈
°
∙
·
√
ⁿ
²
■
NBSP
Hex
00F0
00F1
00F2
00F3
00F4
00F5
00F6
00F7
00F8
00F9
00FA
00FB
00FC
00FD
00FE
00FF
Dec
240
241
242
243
244
245
246
247
248
249
250
251
252
253
251
255
PC850 CODE TABLE (Multilingual)
Char
SP
!
“
#
$
%
&
‘
(
)
*
+
,
-
.
/
Hex
0020
0021
0022
0023
0024
0025
0026
0027
0028
0029
002A
002B
002C
002D
002E
002F
Dec
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
Char
0
1
2
3
4
5
6
7
8
9
:
;
<
=
>
?
Hex
0030
0031
0032
0033
0034
0035
0036
0037
0038
0039
003A
003B
003C
003D
003E
003F
Dec
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
Char
@
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
Hex
0040
0041
0042
0043
0044
0045
0046
0047
0048
0049
004A
004B
004C
004D
004E
004F
Dec
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
Char
P
Q
R
S
T
U
V
W
X
Y
Z
[
\
]
^
_
Hex
0050
0051
0052
0053
0054
0055
0056
0057
0058
0059
005A
005B
005C
005D
005E
005F
Dec
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
Char
`
a
b
c
d
e
f
g
h
i
j
k
l
m
n
o
Hex
0060
0061
0062
0063
0064
0065
0066
0067
0068
0069
006A
006B
006C
006D
006E
006F
Dec
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
Char
p
q
r
s
t
u
v
w
x
y
z
{
|
}
~
⌂
Hex
0070
0071
0072
0073
0074
0075
0076
0077
0078
0079
007A
007B
007C
007D
007E
007F
Dec
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
Char
Ç
ü
é
â
ä
à
å
ç
ê
ë
è
ï
î
ì
Ä
Å
Hex
0080
0081
0082
0083
0084
0085
0086
0087
0088
0089
008A
008B
008C
008D
008E
008F
Dec
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
Char
É
æ
Æ
ô
ö
ò
û
ù
ÿ
Ö
Ü
ø
£
Ø
×
ƒ
Hex
0090
0091
0092
0093
0094
0095
0096
0097
0098
0099
009A
009B
009C
009D
009E
009F
Dec
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
Char
á
í
ó
ú
ñ
Ñ
ª
º
¿
®
¬
½
¼
¡
«
»
Hex
00A0
00A1
00A2
00A3
00A4
00A5
00A6
00A7
00A8
00A9
00AA
00AB
00AC
00AD
00AE
00AF
Dec
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
Char
░
▒
▓
│
┤
Á
Â
À
©
╣
║
╗
╝
¢
¥
┐
Hex
00B0
00B1
00B2
00B3
00B4
00B5
00B6
00B7
00B8
00B9
00BA
00BB
00BC
00BD
00BE
00BF
Dec
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
Char
└
┴
┬
├
─
┼
ã
Ã
╚
╔
╩
╦
╠
═
╬
¤
Hex
00C0
00C1
00C2
00C3
00C4
00C5
00C6
00C7
00C8
00C9
00CA
00CB
00CC
00CD
00CE
00CF
Dec
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
Char
ð
Ð
Ê
Ë
È
ı
Í
Î
Ï
┘
┌
█
▄
¦
Ì
▀
Hex
00D0
00D1
00D2
00D3
00D4
00D5
00D6
00D7
00D8
00D9
00DA
00DB
00DC
00DD
00DE
00DF
Dec
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
Char
Ó
ß
Ô
Ò
õ
Õ
µ
þ
Þ
Ú
Û
Ù
ý
Ý
¯
´
Hex
00E0
00E1
00E2
00E3
00E4
00E5
00E6
00E7
00E8
00E9
00EA
00EB
00EC
00ED
00EE
00EF
Dec
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
Char
SHY
±
‗
¾
¶
§
÷
¸
°
¨
·
¹
³
²
■
NBSP
Hex
00F0
00F1
00F2
00F3
00F4
00F5
00F6
00F7
00F8
00F9
00FA
00FB
00FC
00FD
00FE
00FF
Dec
240
241
242
243
244
245
246
247
248
249
250
251
252
253
251
255
61
PC860 CODE TABLE (Portuguese)
62
Char
SP
!
“
#
$
%
&
‘
(
)
*
+
,
-
.
/
Hex
0020
0021
0022
0023
0024
0025
0026
0027
0028
0029
002A
002B
002C
002D
002E
002F
Dec
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
Char
0
1
2
3
4
5
6
7
8
9
:
;
<
=
>
?
Hex
0030
0031
0032
0033
0034
0035
0036
0037
0038
0039
003A
003B
003C
003D
003E
003F
Dec
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
Char
@
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
Hex
0040
0041
0042
0043
0044
0045
0046
0047
0048
0049
004A
004B
004C
004D
004E
004F
Dec
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
Char
P
Q
R
S
T
U
V
W
X
Y
Z
[
\
]
^
_
Hex
0050
0051
0052
0053
0054
0055
0056
0057
0058
0059
005A
005B
005C
005D
005E
005F
Dec
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
Char
`
a
b
c
d
e
f
g
h
i
j
k
l
m
n
o
Hex
0060
0061
0062
0063
0064
0065
0066
0067
0068
0069
006A
006B
006C
006D
006E
006F
Dec
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
Char
p
q
r
s
t
u
v
w
x
y
z
{
|
}
~
⌂
Hex
0070
0071
0072
0073
0074
0075
0076
0077
0078
0079
007A
007B
007C
007D
007E
007F
Dec
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
Char
Ç
ü
é
â
ã
à
Á
ç
ê
Ê
è
Í
Ô
ì
Ã
Â
Hex
0080
0081
0082
0083
0084
0085
0086
0087
0088
0089
008A
008B
008C
008D
008E
008F
Dec
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
Char
É
À
È
ô
ö
ò
Ú
ù
Ì
Õ
Ü
¢
£
Ù
₧
Ó
Hex
0090
0091
0092
0093
0094
0095
0096
0097
0098
0099
009A
009B
009C
009D
009E
009F
Dec
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
Char
á
í
ó
ú
ñ
Ñ
ª
º
¿
Ò
¬
½
¼
¡
«
»
Hex
00A0
00A1
00A2
00A3
00A4
00A5
00A6
00A7
00A8
00A9
00AA
00AB
00AC
00AD
00AE
00AF
Dec
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
Char
░
▒
▓
│
┤
╡
╢
╖
╕
╣
║
╗
╝
╜
╛
┐
Hex
00B0
00B1
00B2
00B3
00B4
00B5
00B6
00B7
00B8
00B9
00BA
00BB
00BC
00BD
00BE
00BF
Dec
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
Char
└
┴
┬
├
─
┼
╞
╟
╚
╔
╩
╦
╠
═
╬
╧
Hex
00C0
00C1
00C2
00C3
00C4
00C5
00C6
00C7
00C8
00C9
00CA
00CB
00CC
00CD
00CE
00CF
Dec
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
Char
╨
╤
╥
╙
╘
╒
╓
╫
╪
┘
┌
█
▄
▌
▐
▀
Hex
00D0
00D1
00D2
00D3
00D4
00D5
00D6
00D7
00D8
00D9
00DA
00DB
00DC
00DD
00DE
00DF
Dec
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
Char
α
ß
Γ
π
Σ
σ
µ
τ
Φ
Θ
Ω
δ
∞
φ
ε
∩
Hex
00E0
00E1
00E2
00E3
00E4
00E5
00E6
00E7
00E8
00E9
00EA
00EB
00EC
00ED
00EE
00EF
Dec
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
Char
≡
±
≥
≤
⌠
⌡
÷
≈
°
∙
·
√
ⁿ
²
■
NBSP
Hex
00F0
00F1
00F2
00F3
00F4
00F5
00F6
00F7
00F8
00F9
00FA
00FB
00FC
00FD
00FE
00FF
Dec
240
241
242
243
244
245
246
247
248
249
250
251
252
253
251
255
PC863 CODE TABLE (Canadian, French)
Char
SP
!
“
#
$
%
&
‘
(
)
*
+
,
-
.
/
Hex
0020
0021
0022
0023
0024
0025
0026
0027
0028
0029
002A
002B
002C
002D
002E
002F
Dec
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
Char
0
1
2
3
4
5
6
7
8
9
:
;
<
=
>
?
Hex
0030
0031
0032
0033
0034
0035
0036
0037
0038
0039
003A
003B
003C
003D
003E
003F
Dec
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
Char
@
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
Hex
0040
0041
0042
0043
0044
0045
0046
0047
0048
0049
004A
004B
004C
004D
004E
004F
Dec
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
Char
P
Q
R
S
T
U
V
W
X
Y
Z
[
\
]
^
_
Hex
0050
0051
0052
0053
0054
0055
0056
0057
0058
0059
005A
005B
005C
005D
005E
005F
Dec
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
Char
`
a
b
c
d
e
f
g
h
i
j
k
l
m
n
o
Hex
0060
0061
0062
0063
0064
0065
0066
0067
0068
0069
006A
006B
006C
006D
006E
006F
Dec
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
Char
p
q
r
s
t
u
v
w
x
y
z
{
|
}
~
⌂
Hex
0070
0071
0072
0073
0074
0075
0076
0077
0078
0079
007A
007B
007C
007D
007E
007F
Dec
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
Char
Ç
ü
é
â
Â
à
¶
ç
ê
ë
è
ï
î
‗
À
§
Hex
0080
0081
0082
0083
0084
0085
0086
0087
0088
0089
008A
008B
008C
008D
008E
008F
Dec
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
Char
É
È
Ê
ô
Ë
Ï
û
ù
¤
Ô
Ü
¢
£
Ù
Û
ƒ
Hex
0090
0091
0092
0093
0094
0095
0096
0097
0098
0099
009A
009B
009C
009D
009E
009F
Dec
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
Char
¦
´
ó
ú
¨
¸
³
¯
Î
⌐
¬
½
¼
¾
«
»
Hex
00A0
00A1
00A2
00A3
00A4
00A5
00A6
00A7
00A8
00A9
00AA
00AB
00AC
00AD
00AE
00AF
Dec
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
Char
░
▒
▓
│
┤
╡
╢
╖
╕
╣
║
╗
╝
╜
╛
┐
Hex
00B0
00B1
00B2
00B3
00B4
00B5
00B6
00B7
00B8
00B9
00BA
00BB
00BC
00BD
00BE
00BF
Dec
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
Char
└
┴
┬
├
─
┼
╞
╟
╚
╔
╩
╦
╠
═
╬
╧
Hex
00C0
00C1
00C2
00C3
00C4
00C5
00C6
00C7
00C8
00C9
00CA
00CB
00CC
00CD
00CE
00CF
Dec
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
Char
╨
╤
╥
╙
╘
╒
╓
╫
╪
┘
┌
█
▄
▌
▐
▀
Hex
00D0
00D1
00D2
00D3
00D4
00D5
00D6
00D7
00D8
00D9
00DA
00DB
00DC
00DD
00DE
00DF
Dec
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
Char
α
ß
Γ
π
Σ
σ
µ
τ
Φ
Θ
Ω
δ
∞
φ
ε
∩
Hex
00E0
00E1
00E2
00E3
00E4
00E5
00E6
00E7
00E8
00E9
00EA
00EB
00EC
00ED
00EE
00EF
Dec
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
Char
≡
±
≥
≤
⌠
⌡
÷
≈
°
∙
·
√
ⁿ
²
■
NBSP
Hex
00F0
00F1
00F2
00F3
00F4
00F5
00F6
00F7
00F8
00F9
00FA
00FB
00FC
00FD
00FE
00FF
Dec
240
241
242
243
244
245
246
247
248
249
250
251
252
253
251
255
63
PC865 CODE TABLE (Nordic)
64
Char
SP
!
“
#
$
%
&
‘
(
)
*
+
,
-
.
/
Hex
0020
0021
0022
0023
0024
0025
0026
0027
0028
0029
002A
002B
002C
002D
002E
002F
Dec
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
Char
0
1
2
3
4
5
6
7
8
9
:
;
<
=
>
?
Hex
0030
0031
0032
0033
0034
0035
0036
0037
0038
0039
003A
003B
003C
003D
003E
003F
Dec
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
Char
@
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
Hex
0040
0041
0042
0043
0044
0045
0046
0047
0048
0049
004A
004B
004C
004D
004E
004F
Dec
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
Char
P
Q
R
S
T
U
V
W
X
Y
Z
[
\
]
^
_
Hex
0050
0051
0052
0053
0054
0055
0056
0057
0058
0059
005A
005B
005C
005D
005E
005F
Dec
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
Char
`
a
b
c
d
e
f
g
h
i
j
k
l
m
n
o
Hex
0060
0061
0062
0063
0064
0065
0066
0067
0068
0069
006A
006B
006C
006D
006E
006F
Dec
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
Char
p
q
r
s
t
u
v
w
x
y
z
{
|
}
~
⌂
Hex
0070
0071
0072
0073
0074
0075
0076
0077
0078
0079
007A
007B
007C
007D
007E
007F
Dec
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
Char
Ç
ü
é
â
ä
à
å
ç
ê
ë
è
ï
î
ì
Ä
Å
Hex
0080
0081
0082
0083
0084
0085
0086
0087
0088
0089
008A
008B
008C
008D
008E
008F
Dec
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
Char
É
æ
Æ
ô
ö
ò
û
ù
ÿ
Ö
Ü
ø
£
Ø
₧
ƒ
Hex
0090
0091
0092
0093
0094
0095
0096
0097
0098
0099
009A
009B
009C
009D
009E
009F
Dec
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
Char
á
í
ó
ú
ñ
Ñ
ª
º
¿
⌐
¬
½
¼
¡
«
¤
Hex
00A0
00A1
00A2
00A3
00A4
00A5
00A6
00A7
00A8
00A9
00AA
00AB
00AC
00AD
00AE
00AF
Dec
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
Char
░
▒
▓
│
┤
╡
╢
╖
╕
╣
║
╗
╝
╜
╛
┐
Hex
00B0
00B1
00B2
00B3
00B4
00B5
00B6
00B7
00B8
00B9
00BA
00BB
00BC
00BD
00BE
00BF
Dec
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
Char
└
┴
┬
├
─
┼
╞
╟
╚
╔
╩
╦
╠
═
╬
╧
Hex
00C0
00C1
00C2
00C3
00C4
00C5
00C6
00C7
00C8
00C9
00CA
00CB
00CC
00CD
00CE
00CF
Dec
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
Char
╨
╤
╥
╙
╘
╒
╓
╫
╪
┘
┌
█
▄
▌
▐
▀
Hex
00D0
00D1
00D2
00D3
00D4
00D5
00D6
00D7
00D8
00D9
00DA
00DB
00DC
00DD
00DE
00DF
Dec
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
Char
α
ß
Γ
π
Σ
σ
µ
τ
Φ
Θ
Ω
δ
∞
φ
ε
∩
Hex
00E0
00E1
00E2
00E3
00E4
00E5
00E6
00E7
00E8
00E9
00EA
00EB
00EC
00ED
00EE
00EF
Dec
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
Char
≡
±
≥
≤
⌠
⌡
÷
≈
°
∙
·
√
ⁿ
²
■
NBSP
Hex
00F0
00F1
00F2
00F3
00F4
00F5
00F6
00F7
00F8
00F9
00FA
00FB
00FC
00FD
00FE
00FF
Dec
240
241
242
243
244
245
246
247
248
249
250
251
252
253
251
255
PC858 CODE TABLE (Euro symbol)
Char
SP
!
“
#
$
%
&
‘
(
)
*
+
,
-
.
/
Hex
0020
0021
0022
0023
0024
0025
0026
0027
0028
0029
002A
002B
002C
002D
002E
002F
Dec
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
Char
0
1
2
3
4
5
6
7
8
9
:
;
<
=
>
?
Hex
0030
0031
0032
0033
0034
0035
0036
0037
0038
0039
003A
003B
003C
003D
003E
003F
Dec
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
Char
@
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
Hex
0040
0041
0042
0043
0044
0045
0046
0047
0048
0049
004A
004B
004C
004D
004E
004F
Dec
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
Char
P
Q
R
S
T
U
V
W
X
Y
Z
[
\
]
^
_
Hex
0050
0051
0052
0053
0054
0055
0056
0057
0058
0059
005A
005B
005C
005D
005E
005F
Dec
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
Char
`
a
b
c
d
e
f
g
h
i
j
k
l
m
n
o
Hex
0060
0061
0062
0063
0064
0065
0066
0067
0068
0069
006A
006B
006C
006D
006E
006F
Dec
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
Char
p
q
r
s
t
u
v
w
x
y
z
{
|
}
~
⌂
Hex
0070
0071
0072
0073
0074
0075
0076
0077
0078
0079
007A
007B
007C
007D
007E
007F
Dec
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
Char
Ç
ü
é
â
ä
à
å
ç
ê
ë
è
ï
î
ì
Ä
Å
Hex
0080
0081
0082
0083
0084
0085
0086
0087
0088
0089
008A
008B
008C
008D
008E
008F
Dec
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
Char
É
æ
Æ
ô
ö
ò
û
ù
ÿ
Ö
Ü
ø
£
Ø
×
ƒ
Hex
0090
0091
0092
0093
0094
0095
0096
0097
0098
0099
009A
009B
009C
009D
009E
009F
Dec
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
Char
á
í
ó
ú
ñ
Ñ
ª
º
¿
®
¬
½
¼
¡
«
»
Hex
00A0
00A1
00A2
00A3
00A4
00A5
00A6
00A7
00A8
00A9
00AA
00AB
00AC
00AD
00AE
00AF
Dec
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
Char
░
▒
▓
│
┤
Á
Â
À
©
╣
║
╗
╝
¢
¥
┐
Hex
00B0
00B1
00B2
00B3
00B4
00B5
00B6
00B7
00B8
00B9
00BA
00BB
00BC
00BD
00BE
00BF
Dec
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
Char
└
┴
┬
├
─
┼
ã
Ã
╚
╔
╩
╦
╠
═
╬
¤
Hex
00C0
00C1
00C2
00C3
00C4
00C5
00C6
00C7
00C8
00C9
00CA
00CB
00CC
00CD
00CE
00CF
Dec
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
Char
ð
Ð
Ê
Ë
È
€
Í
Î
Ï
┘
┌
█
▄
¦
Ì
▀
Hex
00D0
00D1
00D2
00D3
00D4
00D5
00D6
00D7
00D8
00D9
00DA
00DB
00DC
00DD
00DE
00DF
Dec
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
Char
Ó
ß
Ô
Ò
õ
Õ
µ
þ
Þ
Ú
Û
Ù
ý
Ý
¯
´
Hex
00E0
00E1
00E2
00E3
00E4
00E5
00E6
00E7
00E8
00E9
00EA
00EB
00EC
00ED
00EE
00EF
Dec
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
Char
SHY
±
‗
¾
¶
§
÷
¸
°
¨
·
¹
³
²
■
NBSP
Hex
00F0
00F1
00F2
00F3
00F4
00F5
00F6
00F7
00F8
00F9
00FA
00FB
00FC
00FD
00FE
00FF
Dec
240
241
242
243
244
245
246
247
248
249
250
251
252
253
251
255
NOTE: To print the Euro (€) symbol, the command sequence is: 0x1B, 0x74, 0x13, 0xD5 (see Commands Manual).
65
In CUSTOM/POS emulation, it is possible to use TrueType fonts. To be used, a TrueType font must be monospace type
(every character of the font must have the same dimension). The check is made by the device when the font is selected.
TrueType fonts will be automatically scaled by the device in order to obtain the same available width for the embedded
fonts (11, 15 and 20 cpi).
The quality of TrueType fonts, the correct positioning into the printable area and the available code tables, will result from
the font producers and the font implementation.
For the correct printing of the code tables, it is necessary that the selected TrueType font contains all the characters in
the tables. Otherwise, the ‘�’ symbol will be printed instead the missing character. All commands for printing coniguration are usable both with TrueType fonts and with embedded fonts. It is possible to address the TrueType font respects the
UNICODE™ standard (see www.unicode.org), by using UTF-8 or UTF-16 encoding.
66
8
CONSUMABLES
The following table shows the list of available consumables for device:
DRIPTION
CODE
67300000000410
THERMAL PAPER ROLL
weight = 78g/m2
width = 82.5mm
Ø external = 150mm
Ø core = 40mm
67
68
9
ACCESSORIES
The following table shows the list of available accessories for device:
DRIPTION
CODE
963GE020000003
POWER SUPPLY
(for technical speciications, see the paragraph 7.1)
976BG010000003
RIGHT AND LEFT SIDES KUBE-F
color: black
(see the paragraph 9.1)
69
9.1
Sides replacement
To replace the printer side (right or left), proceed as follows:
1
3
Remove the carter on the printer side
using a screwdriver.
Remove the printer side.
2
NEW
Unscrew the fixing screw
for the printer side.
70
Assemble the new side performing the previous
operations in reverse order.
10
TECHNICAL SERVICE
In case of failure, contact the Technical Service by sending an e-mail to [email protected] detailing:
1. Product code
2. Serial number
3. Hardware release
4. Firmware release
To get the necessary data, proceed as follows:
1
3
XXXXXXXXXXXXXX
Rx
0000000000000000000
Write down the data printed
on the product label (see paragraph 2.3)
[email protected]
Customer Service Department
FW
2
KUBEII SCANNER
SCODE <code>
DCODE <code>
FCODE <code>
UCODE <code>
DCODE <code>
-
rel
rel
rel
rel
rel
1.00
1.00
1.00
1.00
1.00
Send an e-mail to the Technical Service,
with the data collected
PRINTER SETTINGS
PRINTER TYPE .........................................KUBE SCAN 84MM
PRINTING HEAD TYPE .............................SHEC T80
Print a Setup report (see paragraph 5.1)
The Setup report shows
the firmware release
71
72
11
ADVANCED FUNCTIONS
11.1
File sharing
The devices can be connected to a PC through two types of connections (see par.3.3):
1. with USB cable
2. with Ethernet cable.
According to the connection made, it is possible to manage drivers, fonts and logos of the device and conigure the operating parameters in three different ways:
1. by iles sharing from Mass Storage, in case of USB connection
2. by iles sharing from FTP Server connection, in case of Ethernet connection
3. by entering the Embedded Web Server, in case of Ethernet connection.
USB
FILE SHARING
FROM
MASS STORAGE
ETH
EMBEDDED
WEB
SERVER
FTP
SERVER
CONNECTION
73
11.2
Embedded Web Server
Device is equipped with an Embedded Web Server that allows to execute some operations on device, through a clear web
interface, including:
• • • • • • monitoring the device status;
setting operating parameters;
coniguring network settings;
managing the logos;
coniguring the email service to make diagnostics and maintenance operations easier;
download printing drivers.
Before entering in the Embedded Web Server, check that:
• • • • • the device is connected and turned on;
the device has a network connection based on the IP protocol;
the following ports are opened (if a Firewall is present on computer): 9100 (or differently set up). 15000, 15001, 15002;
have a Web browser on the computer;
the device is connected to the network and its IP address and its Subnet Mask are set up in a correct way. To check
the setting of these parameters, open a new terminal window and type “ping” on the command bar followed by the IP
address of the device. The picture shows an example of a positive result after the “ping” command. Otherwise, if connection isn’t possible, to its IP address, a failure notice will appear.
Example:
ping
192. 168. 10. 37
Command Prompt
Microsoft Windows XP [Version 5.1.2600]
(C) Copyright 1985-2001 Microsoft Corp.
C:\>ping 192.168.10.27
Pinging 192.168.10.37 with 32 bytes of data:
Replay
Replay
Replay
Replay
from
from
from
from
192.168.10.37:
192.168.10.37:
192.168.10.37:
192.168.10.37:
bytes=32
bytes=32
bytes=32
bytes=32
time<1mx
time<1mx
time<1mx
time<1mx
TTl=64
TTl=64
TTl=64
TTl=64
Ping statistics for 192.168.10.37:
Packets: sent = 4, Received = 4, Lost = 0 (0% loss.),
Approximate round trip times in milli-seconds:
minimum = 0ms, Maximum = 0ms, Avereage = 0ms
c:\>
74
11.3
Embedded Web Server: access
To enter the Embedded Web Server, type the IP address assigned to the device into Web browser. To know the IP address
of the device, print the Set-up report of the device (see chapter 5) or use “Locator”. For example, if IP address of the device
is 192.168.10.37, type in the Web browser:
http://192.168.10.37
On the screen will appear the internal default page that corresponds to the section “Device Info” The home page is divided
into 6 areas whose functions are dribed below:
1.
SECTIONS:
The web server has three sections listed within each web page. These sections are:
Device Info, Printer Settings, Printer Support.
2.
CURRENT PAGE
Reports section currently displayed.
3.
TOOLS
Lists the tools available within the chosen section.
4.
PRINTER PICTURE
Displays a picture representative of the device operational status. The picture changes
depending on the parameters reported in area number 5.
5.
REAL TIME STATUS
Report a list of operating parameters controlled and monitored in real time (with a regular
refresh from 5 to 15sec).
6.
TIME AND DATE
Displays the current time and date.
1
DEVICE INFO │ PRINTER SETTINGS │ PRINTER SUPPORT
Web Site
R>
TE
RIN
< Device name >
<P
2
DEVICE INFO
Cover Open
RealTime Status
Cover Open
Model Information
Paper End
3
Printer Parameter
Near Paper End
Network Settings
Paper rolling
Advanced Status
Paper End
Ticket Out
LF key pressed
4
R>
TE
N
I
R
<P
FF key pressed
S1 key pressed
5
S2 key pressed
Over temperature
Supply Voltage error
Cutter error
Cutter Open
Memories Error
Paper Jam
6
12:00
01-01-14
Notch Search...
Notch Error
75
To enter some sections and some coniguration services, it is required the identiication of the user and password. To make registration and to obtain the access to the restricted areas, when it is required insert the user name and the password
as indicated in the following table:
User Name
Password
NOTE: Respect capital and small letters as indicated in table.
76
Custom
AlwaysOn
11.4
Embedded Web Server: functions
The “Printer Settings” section is a restricted one. To enter the section, it is required the identiication of the user and password. With the tools of this section, it is possible to set up the same parameters of the device that are conigurable in the device’s Set-up mode (see chapter 5).
The following igure shows the page for the “EMAIL SETUP” tool. It is divided into 4 areas:
1.
SECTIONS:
Are the same as dribed on the main page
2.
CURRENT PAGE
Reports section currently displayed.
3.
TOOLS
Lists the tools available within the chosen section.
4.
EMAIL SETUP
Displays the ields available to conigure the automatically delivery of service email in order to inform the user when a change occurs to operating status of the device. It is
possible to select the events to enable the sending of the email
1
DEVICE INFO │ PRINTER SETTINGS │ PRINTER SUPPORT
Web Site
< Device name >
R>
TE
RIN
<P
2
PRINTER SETTINGS
Printer Setup
Network Setup
3
Email Setup
E-Mail Service Settings
SMTP Server Address
SMTP Server Port
E-mail To
smtp.xxxxxx.it
25
[email protected]
Email Log
E-mail From
E-mail Subject
<PRINTER>@xxxxxxx.it
test
Testo libero
E-mail Message
Include Printer Status
4
when Paper End is detected
when Near Paper End is detected
on Printer Power On
when Near Paper End is detected
on Cut
on LF key pressed
on FF key pressed
Send e-mail event
on S1 key pressed
on S2 key pressed
on Cut error
on Paper Jam
on Notch Align error
on Autoload
on Head Over Temperature error
on Supply Voltage error
Reset e-mail settings...
Save e-mail settings
77
With the tools in the “Printer Support” section, it is possible to download drivers, manage logos and test some device function for demonstrative and service purpose,
The following igure shows the page for the “ADVANCED FUNCTIONS” tool. It is divided into 4 areas:
1.
SECTIONS:
Are the same as dribed on the main page
2.
CURRENT PAGE
Reports section currently displayed.
3.
TOOLS
Lists the tools available within the chosen section.
4.
ADVANCED FUNCTION
Displays all the tests available for the device: printing a test page, the font test and the
logos test, the self-calibration of the notch sensors and the ticket alignment.
1
DEVICE INFO │ PRINTER SETTINGS │ PRINTER SUPPORT
Web Site
T
RIN
ER
< Device name >
>
<P
2
PRINTER SUPPORT
Advanced Function
Download Driver
Warning : Use these function only when the printer is in standby!
All functions below, if used while the printer is executing a print job from communication port, may corrupt the printout.
Advanced Function
3
Test Page
Picture Settings
Font Settings
Print Test Page
Exec Test Page
Firmware Upgrade
Logo Test
Logo Description
Logo Test
Print all Logos
Exec Logo Test
Font Test
Font Description
Font Test
CUSTOM/POS - 11 CPI
Exec Font Test
Advanced Function
Notch Autoset
Characterize Paper
Align icket to print
Align ticket to cutter
Cut Paper
Reset To Factory Default
78
Exec Notch Autoset
Exec Paper Characterization
Exec Align
Exec Align to cut
Exec Paper Cut
Reset To Factory Default
4
11.5
Locator
With the device it is possible to use an external software to perform a search for devices connected to the network with
Ethernet cable, even without knowing the IP addresses of individual device
The following igure shows the software interface:
1.
DEVICES:
Displays the list of the connected devices.
2.
“START...”
Stars a new search.
3.
“CONF.” Enters the coniguration window of the network parameters of the selected device.
1
3
2
79
11.6
Drivers installation
Embedded Web Server
To install a new driver update for the device, enter the “DRIVER” page of the “PRINTER SUPPORT” section of the embedded Web Server (see the following igure).
DEVICE INFO │ PRINTER SETTINGS │ PRINTER SUPPORT
Web Site
T
RIN
<P
ER
>
< Device name >
PRINTER SUPPORT
Download Driver
Download Driver
Advanced Function
You can find on this section the printer drivers.
The drivers are stored inside the printer memory: is not needed an active internet connection
Picture Settings
Font Settings
Firmware Upgrade
<Printer>_rel_111_Win2K_2K3_XP.exe | | Release : 1.11 | | File Size : 37 KB
Microsoft Windows GPD Driver
Related product(s) : <PRINTER>
Category : Drivers
Operative system(s) : Windows 2000 / XP / Vista
Download file >>
<Printer>_cupsdrv-1.00.tar.gz | | Release : 1.00 | | File Size : 12 KB
CUPS (Common Unix Printer System) based printer drivers
Related product(s) : <PRINTER>
Category : Drivers
Operative system(s) : Linux
Download file >>
Mass Storage / FTP Server
It is possible to install the new driver update directly into the folder “DRIVER” on the Flash Drive of the device.
You can enter the Flash Drive by iles sharing from Mass Storage or by iles sharing from FTP Server connection (see par.11.1).
In both cases, the relative parameter should be enabled during the coniguration process (see chapter 5).
NOTE: To know the IP address of the device, print the Set-up report of the device (see chapter 5) or use “Locator”.
Type in the address bar “ftp://” followed by the IP address of the device.
80
11.7
Logos management
It is possible to store new logos in addition to default logos stored on Flash Disk. The device automatically provides to
convert BMP image to the error-diffusion format in black and white.
Logos may be stored both on Flash Disk and on the Memory Card. The use of the Memory Card allows to handle more
logos (however, the max number of manageable logos is limited by the RAM memory reserved for logos management).
Embedded Web Server
To add a new logo to the device enter the “PICTURE SETTINGS” page of the “PRINTER SUPPORT” section of the embedded Web Server (see the following igure).
DEVICE INFO │ PRINTER SETTINGS │ PRINTER SUPPORT
Web Site
T
RIN
<P
ER
< Device name >
>
PRINTER SUPPORT
Picture Settings
Download Driver
Advanced Function
Warning : Use these function only when the printer is in standby!
All functions below, if used while the printer is executing a print job from communication port, may corrupt the printout.
Picture Settings
Font Settings
Firmware Upgrade
Add New Logo
Sfoglia...
Picture to Add
Logo Number
Logo Destination
Send Test
Flash Disk
Add New Logo
File System Free Space
Flash Drive
Memory Card
Free 1.02 Mb
Disk Not Found
Logo Test
Logo Description
Logo Test
Print all Logos
1 - Pict1.bmp
Exec Logo Test
Logo Test
Logo Description
Delete Logo
1 - Pict1.bmp
Delete Selected Logo
81
Mass Storage / FTP Server
It is possible to add the new logo directly into the folder “PICTURES” on the Flash Drive of the device.
You can enter the Flash Drive by iles sharing from Mass Storage or by iles sharing from FTP Server connection (see par. 11.1).
In both cases, the relative parameter should be enabled during the coniguration process (see chapter 5).
After adding the logo, open the coniguration ile “PictList.ini” and add a new line with a number associated to the logo (to be used with device’s commands), a letter for the memory unit and the logo ile name, as indicated in the instructions written inside the “PictList.ini” ile.
To delete a logos stored in the device, proceed as follows:
1. delete the selected logo from the “Pictures” folder on Flash Disk or SD/MMC card;
2. in the coniguration ile “PictList.ini”, delete the line related to the erased logo.
The logos stored into a unit memory and converted by the device, can be printed by using the number associated to the
logo during the conversion step.
The correspondence between ile-name and logo-number is warrant by the coniguration ile “PIctList.ini” and it is veriiable with the logo test.
ATTENTION: The coniguration ile “PictList.ini” on the device’s Flash Disk, has to be modiied even if the new added logo is stored on SD/MMC.
NOTE: To know the IP address of the device, print the Set-up report of the device (see chapter 5) or use “Locator”.
Type in the address bar “ftp://” followed by the IP address of the device.
82
11.8
Fonts management
It is possible to store new font in addition to default fonts stored on Flash Disk. Fonts may be stored both on Flash Disk
and on the Memory Card.
The use of the Memory Card allows to handle more fonts (however, the max number of manageable fonts is limited by the
RAM memory reserved for fonts management).
Embedded Web Server
To add a new font to the device enter the “FONT SETTINGS” page of the “PRINTER SUPPORT” section of the embedded
Web Server (see the following igure).
DEVICE INFO │ PRINTER SETTINGS │ PRINTER SUPPORT
Web Site
T
RIN
<P
ER
< Device name >
>
PRINTER SUPPORT
Font Settings
Download Driver
Advanced Function
Warning : Use these function only when the printer is in standby!
All functions below, if used while the printer is executing a print job from communication port, may corrupt the printout.
Picture Settings
Font Settings
Firmware Upgrade
Add New Font
Sfoglia...
Font to Add
Font Destination
Send Font
Add New Font
File System Free Space
Flash Drive
Memory Card
Free 1.02 Mb
Disk Not Found
Font Test
Font Description
Vera.ttf
CUSTOM/POS - 11 cpi
Flash Disk
Font Test
Exec Font Test
Print Embedded Font Charmap
Delete Existing Font
Font Description
Delete Font
Vera.ttf
Flash Disk
Delete Selected Font
83
Mass Storage / FTP Server
It is possible to add the new font directly into the folder “FONTS” on the Flash Drive of the device.
You can enter the Flash Drive by iles sharing from Mass Storage or by iles sharing from FTP Server connection (see par. 11.1).
In both cases, the relative parameter should be enabled during the coniguration process (see chapter 5).
NOTE:
To know the IP address of the device, print the Set-up report of the device (see chapter 5) or use “Locator”. Type in the
address bar “ftp://” followed by the IP address of the device.
Uploading the new font directly from the “Font” folder of Microsoft® Windows® directory, remember that the displayed
font name into the “Font” folder may not match the real name of the font ile.
84
11.9
Printer setup
Embedded Web Server
Device permits the coniguration of default parameters for device and network setup by entering the “PRINTER SETUP” page and the “NETWORK SETUP” page of the “PRINTER SETTINGS” section of the embedded Web Server (see the
following igure).
DEVICE INFO │ PRINTER SETTINGS │ PRINTER SUPPORT
Web Site
T
RIN
<P
ER
< Device name >
>
PRINTER SETTINGS
< PRINTER > Printer Settings
Printer Emulation
Printer Setup
Network Setup
Email Setup
Email Log
Autofeed
Chars/inch
Busy Condition
Print Mode
Print Density
Speed/Quality
Paper Width
Paper Threshold
Notch Position
CUSTOM/POS
CR disabled
1
2
3
4
5
6
7
8
18
9
10
11
12
13
14
15
RxFull
19
16
17
18
19
20
21
22
20
23
24
25
26
27
28
29
Normal
21
30
31
17
0%
High Speed
Time:
12 : 00
Select date
Apply Date and Time
82 mm
40 %
Disabled
40 %
Notch Distance
+0.0
Ticket Locking
16
A=15 B=20 cpi
Notch Threshold
Paper End Buffer Clear
?
January, 2014
<< < Today > >>
wk Sun Mon Tue Wed Thu Fri Sat
Disabled
Disabled
COM Port Settings
RS232 Baud Rate
RS202 Data Lenght
115200 bps
8 bits/chr
Mass Storage / FTP Server
It is possible to conigure the default parameters for device and network setup by editing the “Setup.ini” ile on the device Flash Drive.
You can enter the Flash Drive by iles sharing from Mass Storage or by iles sharing from FTP Server connection (see par.11.1).
In both cases, the relative parameter should be enabled during the coniguration process (see chapter 5).
After editing device’s parameter, simply save the “Setup.ini” ile to make the modiies activated.
85
The “Setup.ini” ile is a coniguration ile that contains all the conigurable parameters listed in text format and divided into some sections (indicated in square brackets).
The available values for every parameter, are listed after the parameter name. The value marked with the symbol ‘ * ’ is the
default one. To modify device’s parameters, change the numeric value after the name of parameters. To set the parameter
to the default value, change the numeric value with the symbol D.
The “Setup.ini” ile permits the coniguration of the following parameters:
[PRINT]
Print Mode
0*, 1
0 = Normal
1 = Reverse
Autofeed
0*, 1
0 = CR disabled
1 = CR enable
Chars / inch
0, 1*
0 = A=11 B=15 cpi
1 = A=15 B=20 cpi
Speed / Quality
0, 1, 2*
0 = High Quality
1 = Normal
2 = High Speed
Paper Width
9, 10, 11, 12, 13, 14*
9 = 72 mm
10 = 74 mm
11 = 76 mm
Total cut ( i)
0*, 1
0 = Enabled
1 = Disabled
PaperEnd Buffer Clear
0, 1*
0 = Disabled
1 = Enabled
Binary Log File
12 = 78 mm
13 = 80 mm
14 = 82 mm
< Reserved >
PowerFail WakeUp Mode
0, 1, 2*
0 = Always OFF
1 = Always ON
2 = LAST PWR State
Print Density
0, 1, 2, 3, 4*, 5, 6, 7, 8
0 = - 50 %
1 = - 37 %
2 = - 25 %
3 = - 12 %
4=0%
5 = + 12 %
6 = + 25 %
7 = + 37 %
8 = + 50 %
1, 2, 3, 4, 5, 6, 7, 8*
1 = 1200 bps
2 = 2400 bps
3 = 4800 bps
4 = 9600 bps
5 = 19200 bps
6 = 38400 bps
7 = 57600 bps
8 = 115200 bps
[INTERFACE]
RS232 Baud Rate
86
RS232 Data Length
0*, 1
0 = 8 bits/chr
1 = 7 bits/chr
RS232 Parity
0*, 1, 2
0 = None
1 = Even
RS232 Handshaking
0*, 1
0 = Xon/Xoff
1 = Hardware
Busy Condition
0*, 1
0 = RxFull
1 = OffLine/RxFull
USB Address Number
0*, 1, 2, 3, 4, 5, 6, 7, 8, 9
0=0
1=1
2=2
3=3
USB Interface 2
0, 1, 2*
0 = Disabled
1 = Mass Storage
2 = Status Mon.
DHCP Client
0*, 1
0 = Disabled
1 = Enabled
FTP Server
0*, 1
0 = Disabled
1 = Enabled
2 = Odd
4=4
5=5
6=6
7=7
8=8
9=9
[NETWORK]
IP Address
Subnet Mask
Default Gateway
Domain Name System
TCP Printer Port
MAC Address (Solo lettura)
NOTE:
To know the IP address of the device, print the Set-up report of the device (see chapter 5) or use “Locator”. Type in the
address bar “ftp://” followed by the IP address of the device.
87
11.10
VeriPrint® setup
Mass Storage / FTP Server
It is possible to conigure the default parameters for VeriPrint system by editing the “Scanner.cfg” ile on the device Flash Drive. You can enter the Flash Drive by iles sharing from Mass Storage or by iles sharing from FTP Server connection (see par.11.1).
In both cases, the relative parameter should be enabled during the coniguration process (see chapter 5).
After editing device’s parameter, simply save the “Scanner.cfg” ile to make the modiies activated.
The “Scanner.cfg” ile is a coniguration ile that contains all the conigurable parameters listed in text format and divided into some sections (indicated in square brackets).
The available values for every parameter, are listed after the parameter name. The value marked with the symbol ‘ * ’ is the
default one. To modify device’s parameters, change the numeric value after the name of parameters. To set the parameter
to the default value, change the numeric value with the symbol D.
The “Scanner.cfg” ile permits the coniguration of the following parameters:
SCANHRES
600*, 300
scanner horizontal resolution
SCANVRES
400*, 200
scanner vertical resolution
SAVETIMEMODE
0, 1, 2*
save time mode:
0 = after cut
1 = after motor off
2 = after cut or motor off
BWTHRESHOLD
0 ÷ 255 (150*)
black/white threshold
LASTHRES
SCANHRES, 300*, 200
bmp horizontal resolution saved in LASTSCAN disk
LASTVRES
SCANVRES, 300*, 200
bmp vertical resolution saved in LASTSCAN disk
LASTBITPIX
8, 4*, 1
profondità colori del bmp salvato nel disco LAST IMAGE
LASTFILENAME
‘image’*, 0, 1, 2
bmp name saved in LASTSCAN disk:
‘image’ = <name of ile without extension, max 12 chars>
0 = no ile
1 = DDMMYYhhmmss.bmp
2 = YYMMDDhhmmss.bmp
LASTCROP:
0*, 1
crop of bmp saved in LASTSCAN disk:
0 = no crop
1 = crop
JOURHRES
SCANHRES, 300, 200*
bmp horizontal resolution saved in SD/MMC CARD
JOURVRES
SCANVRES, 300, 200*
bmp vertical resolution saved in SD/MMC CARD
JOURBITPIX
8, 4, 1*
colour depth of bmp saved in SD/MMC CARD
88
JOURFILENAME
‘image’*, 0, 1, 2
bmp salvato nel disco SD/MMC CARD
‘image’ = <name of ile without extension, max 12 chars>
0 = no ile
1 = DDMMYYhhmmss.bmp
2 = YYMMDDhhmmss.bmp
JOURFULLMODE
0*, 1, 2
SD/MMC CARD full behaviour:
0 = erase oldest folders
1 = ile not saved
2 = stop print
JOURCROP
0, 1*
crop of bmp saved in SD/MMC CARD:
0 = no crop
1 = crop
ATTENTION:
To obtain the best results is recommended to use max resolution for scanning and saving the image.
The SCANHRES and SCANVRES parameters deine indirectly the maximum scanning length:
SCANHRES
600
600
300
300
SCANVRES
400
200
400
200
MAX SCANNING LENGTH
275 mm
550 mm
550 mm
1100 mm
89
11.11
Scanner unit setup
Mass Storage / FTP Server
It is possible to conigure the default parameters for scanner unit by editing the “Scanner_ext.cfg” ile on the device Flash Drive. You can enter the Flash Drive by iles sharing from Mass Storage or by iles sharing from FTP Server connection (see par.11.1).
In both cases, the relative parameter should be enabled during the coniguration process (see chapter 5).
After editing device’s parameter, simply save the “Scanner_ext.cfg” ile to make the modiies activated.
The “Scanner_ext.cfg” ile is a coniguration ile that contains all the conigurable parameters listed in text format and divided into some sections (indicated in square brackets).
The available values for every parameter, are listed after the parameter name. The value marked with the symbol ‘ * ’ is the
default one. To modify device’s parameters, change the numeric value after the name of parameters. To set the parameter
to the default value, change the numeric value with the symbol D.
The “Scanner_ext.cfg” ile permits the coniguration of the following parameters:
MAXINCLINATIONS
10 ÷ 50 (30*)
(*1024) maximum card inclination
SWTHRESHOLDPOINTEXT
13*
% software threshold card point
BWTHERSHOLDEXT
0 ÷ 255 (180*)
black/white threshold
SCANMODE
0 ÷ 15 (3*)
searching modanner:
0 = no search
1 = card
2 = barcode
SEARCHTIMEAUTOLOAD
60*
(*10msec) timeout autoload scanner
FILEERRORCARD
0, 1*
ile containing the consistency check of the ticket:
0 = no ile
1 = .log
LASTBITPIXEXT
8, 4*, 1
colour depth of bmp saved in LAST IMAGE
LASTFILENAMEEXT
‘image_ext’*, 0, 1, 2
bmp name saved in LASTSCAN disk:
‘image_ext’ = <name of ile without extension, max 12 chars>
0 = no ile
1 = DDMMYYhhmmss.bmp
2 = YYMMDDhhmmss.bmp
LASTCROPEXT
0*, 1
crop of bmp saved in LASTSCAN disk:
0 = no crop
1 = crop
LASTBETFILEEXT
0*, 1
ile containing the searching result:
0 = no ile
1 = .txt
90
JOURBITPIXEXT
8, 4, 1*
colour depth of bmp saved in SD/MMC CARD
JOURFILENAMEEXT
‘image’*, 0, 1, 2
bmp name saved in SD/MMC CARD:
‘image’ = <name of ile without extension, max 12 chars>
0 = no ile
1 = DDMMYYhhmmss.bmp
2 = YYMMDDhhmmss.bmp
JOURFULLMODE
0*, 1, 2
SD/MMC CARD full behaviour:
0 = erase oldest folders
1 = ile not saved
2 = stop print
JOURCROP
0, 1*
crop of bmp saved in SD/MMC CARD:
0 = no crop
1 = crop
91
Rev. 1.10
Part Number : 76200000004600
CUSTOM S.p.A.
World Headquarters
Via Berettine, 2/B - 43010 Fontevivo, Parma ITALY
Tel. +39 0521 680111 - Fax +39 0521 610701
[email protected] - www.custom.biz
All rights reserved
www.custom.biz
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement