AcuRite | ENC 150 | Specifications | AcuRite ENC 150 Specifications

AcuRite ENC 150 Specifications
ENC 150™
REFERENCE MANUAL
ACU-RITE
®
ENC150
Table of Contents
Page
Introduction .............................................................................. 2
Mounting Preparation ...............................................................
Mounting Information ...............................................................
Encoder Dimensions ................................................................
Backup Spar Dimensions ........................................................
Page
Spar Installation Procedure ..................................................... 11
Checking your Installation ........................................................ 13
Electrical Shielding ................................................................ 14
Troubleshooting ..................................................................... 15
3
4
5
6
Mechanical Specifications ..................................................... 16
Output Signals and Pin-Outs ................................................. 17
Electrical Specifications ......................................................... 18
Mounting Requirements ........................................................... 7
Typical Mounting (s) ................................................................. 8
Encoder Installation Procedure ............................................... 9
The ACU-RITE Warranty ....................................................... 19
Horizontal mt.
bracket
Reading Head
bracket
Side mount
bracket
Extension
bracket
Motor mount
Rear mount
bracket
• Installation brackets and kits are available.
• Your Authorized ACU-RITE Distributor can assist you with your
selection of these for your installation.
1
ACU-RITE
®
Introduction
ENC 150
The ENC 150 precision glass scale linear encoder provides the
accuracy and reliability of an ACU-RITE measuring system with
digital output (analog output available). Features and options
include:
For future ordering information or warranty service, record the linear
encoder catalog number located on the scale assembly tag, and
the serial number from the reading head tag.
•
•
•
•
•
Axis # 1:
Axis # 2:
Axis # 3:
Axis # 4:
Resolutions of .5, 1, 2, 5, or 10 µm.
Accuracy grades of ± 3, and ± 5 µm / 1000 mm.
Vinyl or Armor cables of 2, 5, 10, 15 and 20 ft. length.
Fasteners, center supports, and backup spars.
Brackets and accessories.
Contact your Authorized ACU-RITE Distributor for assistance with
the selection of product options and accessories.
Catalog No.
_______________
_______________
_______________
_______________
Serial No.
__________________
__________________
__________________
__________________
Date of purchase: _______________
__________________
Distributor:
Address:
Telephone:
Contents
< 60”
____________________________________
____________________________________
____________________________________
Contents
> 65”
A
A
C
D
E
F
B
C
E
D
A) ENC 150 Linear Encoder
B) Backup Spar
C) Reference Manual
ACU-RITE
®
D) Cable Mounting Hardware
E) Linear Encoder Mounting Hardware
F) Backup Spar Mounting Hardware
2
ENC150
Mounting Preparation
Please follow these preparation guide lines.
•
•
•
•
Understand your mounting requirements.
Mount with lip seals down and away from the work area.
Brackets should be kept as short as possible and rigid.
Surfaces must be in good condition, clean, and free of dirt.
Remove paint from machined mounting surfaces.
Alignment brackets must not be removed until instructed.
•
1.150
1.150
“L”
“L” = Measuring length
+ 1.75” nominal
over travel
• Machine travel can not exceed the encoder measuring length.
• Either limit machine travel or obtain correct length scale.
Cable direction
Rotate reading head
base 180°
• Never mount with lip seals upward or towards work area.
• Determine cable exit direction before installing.
• To change cable exit direction; remove base and rotate 180°.
3
ACU-RITE
®
Mounting Information
ENC150
Use this information to plan your Linear Encoder installation.
1.826 ±.010 [46.5]
// .010 A
• Mount the linear encoders close to machine guide ways to ensure
system accuracy.
• One side of the linear encoder addresses flush mounting surfaces,
and the opposite side addresses offset mounting surfaces.
• If space between the reading head and the mounting surface
exceeds .18”, use a spacer or mounting bracket to reduce space.
• ACU-RITE bracket kit instructions provide step by step installation
proceedures.
// .010 A
-AScale case
= Machine Travel
Reading head
B
// .010 B
0.0 ± .010
// .010 A
// .010 A
Equal
Equal
• Tolerances of .010” TIR apply to all mounting dimensions.
• Center support mounting surface required for 24” through 60”
linear encoder measuring lengths mounted without a spar.
Alignment bracket removal clearance
Alignment
bracket
1.0
[25mm]
1.38
[35mm]
Alignment
bracket
Move bracket past
the cable strain relief
Flush
mounting
• Allow clearance for alignment bracket removal.
•
Alignment brackets must not be removed until instructed.
ACU-RITE
®
Offset
mounting
Backup spar
mounting
• Use reading head leveling set screws when surfaces are not flush.
• Reading head bracket required for a space >.18”.
4
ENC150
Encoder Dimensions
.810
[20.6]
.285 [7.2]
Measuring length + 6.375
.469
[11.9]
Measuring length + 5.437
.937
[23.8] .562
[14.3]
End Cap
Mounting hole
Scale case
.750
[19.0]
1.826
[46.4]
.944
[24.0]
.320
[8.1]
∅ .500 C’Bore
∅ .313 Thru
.700
[17.8]
.121
[3.11]
Reading Head
assembly
.100
[2.5]
.56
[14.4]
1.125
[28.6]
2.250
[57.1]
.32
.20
[8.4]
[5.2]
Armor
Vinyl
∅ For 8-32
(or M4) SHCS
1.25 [32]
mounting
Min. bend rad.
screw
Max. nominal linear encoder over travel 1.825
Published over travel 1.75”
1.12
[28.5]
.570
[14.5]
.810
[20.5]
.750
[19.0]
1.440
[36.6]
2.148
Ref.
[54.6]
.250
[3.4]
5
1.060
[27.0]
With Backup
Spar
.660
[16.8]
ACU-RITE
®
Backup Spar Dimensions
ENC 150
Backup spar
Part Number
Linear Encoder
Measuring Length
L
A
X No.
Places
B
385102-000
385104-000
385106-000
385108-000
385110-000
385112-000
385113-000
385114-000
385116-000
385118-000
385120-000
385122-000
385124-000
385126-000
385128-000
385130-000
385131-000
385132-000
2
4
6
8
10
12
13 (Special)
14
16
18
20
22
24
26
28
30
31.5
32 (“E” 34.812)
8.312
10.312
12.312
14.312
16.312
18.312
19.312
20.312
22.312
24.312
26.312
28.312
30.312
32.312
34.312
36.312
38.030
35.687
1.656
2.656
1.156
2.156
3.156
4.156
1.44
5.156
1.156
2.156
3.156
4.156
5.156
1.156
2.156
3.156
4.015
.437
2
2
2
2
2
2
2
2
3
3
3
3
3
4
4
4
4
4
5.000
5.000
10.000
10.000
10.000
10.000
16.43
10.000
10.000
10.000
10.000
10.000
10.000
10.000
10.000
10.000
10.000
11.604
Backup spar
Part Number
Linear Encoder
Measuring Length
L
A
X No.
Places
B
385135-000
385136-000
385138-000
385140-000
385142-000
385148-000
385152-000
385154-000
385160-000
35 (“E” 40.437)
36
38
40
42
48
52
54
60
65
72
78
84
90
100
110
120
41.312
42.312
44.312
46.312
48.312
54.312
58.312
60.312
66.312
71.312
78.312
84.312
90.312
96.312
106.312
116.312
126.312
.437
1.156
2.156
3.156
4.156
2.156
4.156
5.156
3.156
5.656
4.156
2.156
5.156
3.156
3.156
3.156
3.156
5
5
5
5
5
6
6
6
7
7
8
9
9
10
11
12
13
10.109
10.000
10.000
10.000
10.000
10.000
10.000
10.000
10.000
10.000
10.000
10.000
10.000
10.000
10.000
10.000
10.000
With Encoder
With Encoder
With Encoder
With Encoder
With Encoder
With Encoder
With Encoder
With Encoder
“L” ± .015
“A” ± .015
.110 ± .005
5.000 typ. ± .015
Non
Accumulative
M4 Thru
.750 ± .005
∅ .312 Thru
∅ .500 C’Bore x .160 Dp.
“X” No. of holes
“B” typ. ± .015
Non Accumulative
“A” ± .005
ACU-RITE
®
“E”
“A” Ref.
6
ENC150
Mounting Requirements
Mounting options can be adapted to machine mounting surfaces
using spacers, standoffs, or leveling set screws.
End hole mounting
with center support
• Measuring length and mechanical configuration of your machine
determine your options.
• Backup spar mounting is an option but not required for lengths
up to 60”.
• Fastener lengths described on this page are included with the
encoder or the backup spar.
Center
support
1/4-20 x 3/4”
SHCS
.94 [23.8]
Linear
Encoder
washer
1/4-20 x 1” BHCS
Typical (supplied)
• 24” to 60” : Use end mounting holes with center support.
End hole mounting
Backup spar
mounting
1/4-20 x 1” BHCS
& scale washer
(supplied)
M4 x 8mm
SHSS
1/4-20 x 1/2” BHCS
and spar washer
(supplied)
• Less than 24” : Use end mounting holes.
• Over 60” : A backup spar is required.
7
ACU-RITE
®
Typical Mounting (s)
ENC 150
A variety of mounting conditions can be accommodated.
Offset surfaces
• The machine configuration determines the brackets required to
install the linear encoder.
• Three typical mounting conditions are shown; flush, offset, and
backup spar (as shown previously on page 4).
• The 8-32 SHCS fastener lenghts shown on this page are typical
to the trim length requirement of the 1” long fastener supplied.
• The 8-32 SHCS for mounting the reading head is a standard low
head style fastener.
1/4-20 x 1” BHCS
with encoder washer
8-32 x 1” SHCS
Space of < .18” use reading head
leveling set screws.
• Mounting surfaces are offset.
• Installation without backup spar.
• Use leveling screws in place of spacers or shims.
Flush surfaces
Backup spar with
bracket
1/4-20 x 1/2” BHCS
and spar washer
1/4-20 x 1” BHCS
and encoder washer
.005
1/4-20 x 1/2” BHCS
and washer
8-32 x 3/4” SHCS (trim)
A space >.18”, use a spacer or
bracket (shown); <.18” use
leveling set screws.
0.0 ± .005
• Mounting surfaces are flush within .005”.
• The reading head leveling screws are not required.
ACU-RITE
®
8-32 x 5/8” SHCS
(trim)
• Flush or offset mounting surfaces with a backup spar.
• Bracket used to reduce head to mounting surface gap.
• Use reading head leveling set screws.
8
ENC150
Encoder Installation Procedure
These steps apply to all encoder mounting conditions, if a spar is
being used, go to “Spar Installation Procedure” on page 11.
Center mounting
axis
•
ACU-RITE bracket kit instructions supercede this section.
• Adjust drill depths and fastener lengths as required.
• When instructed on page 10: Adjust the leveling set screws as
follows:
1. Insert, but do not tighten 8-32 (M4) reading head screws.
2. Place a .001”-.003” shim between the leveling set screws and
mounting surface.
3. Adjust each set screw until a slight drag is felt on the shim.
4. Evenly tighten the 8-32 (M4) reading head mounting
screws.
• Contact your Authorized ACU-RITE Distributor should you require
additional assistance.
CL
Mark center
of axis
• Move the machine axis to its center of travel.
• Mark the axis for quick return to center.
• Configure the encoder cable exit direction (see page 3).
-A- = Axis travel
Scale case
Alignment
brackets (2)
CL
Center marks
Axis parting line
Align top of scale case to
within .015” of -AScale case
Endcap
Cable assembly
Reading head assembly
End mounting hole (typical)
• Align the center marks on the reading head and scale assembly
by sliding the reading head and brackets along the case.
• Locate the scale case so underside of endcaps are flush with the
axis parting line.
• Mark one end mounting hole location.
9
ACU-RITE
®
Encoder Installation Procedure
-A- = Axis travel
ENC 150
Drill / tap
for 1/4-20 (M6).
Drill / tap for 8-32 (M4).
Align to within .010” TIR
to -A-
8-32 x 3/4” SHCS
(M4 x 20mm)
Do not tighten prior to adjusting
leveling set screws.
1/4-20 x 1” BHCS & Scale flat washer
(M6 x 25mm)
• Drill / tap the first end mounting hole / attach the linear encoder.
• Align to within .010” TIR. to -A-, drill / tap second end hole.
• Attach the linear encoder / align to within .010” TIR. to -A-.
• Center the axis and mark the reading head mounting holes.
• Move axis, drill / tap holes for 8-32 (M4).
• Attach head to axis / Set leveling screws / Secure fasteners.
Center support
Alignment bracket
removal
1/4-20 x 3/4” SHCS
(M4 x 20mm)
Slide brackets away from reading
head and cable.
twist 45°
• Use the center support(s) when provided.
• Place supports at equal intervals along the encoder’s length.
ACU-RITE
®
• Slide the brackets away from the reading head.
• Remove the alignment brackets and save for future use.
• Proceed to page 13, “Checking Your Installation”.
10
ENC150
Spar Installation Procedure
These steps apply to all spar mounting conditions.
•
ACU-RITE bracket kit instructions supercede this section.
• Adjust drill depths and fastener lengths as required.
• When instructed on page 12: Adjust the leveling set screws as
follows:
1. Insert, but do not tighten 8-32 (M4) reading head screws.
2. Place a .001”-.003” shim between the leveling set screws and
mounting surface.
3. Adjust each set screw until a slight drag is felt on the shim.
4. Evenly tighten the 8-32 (M4) reading head mounting
screws.
• Contact your Authorized ACU-RITE Distributor should you require
additional assistance.
-A- = Axis travel
Axis parting line
Align top of spar to within
.015” of -A-
End mounting hole (typical)
• Locate the spar with the underside flush with the axis parting line.
• Mark one end mounting hole location.
Center mounting
axis
-A- = Axis travel
CL
Align to within .010” TIR of -AMark center
of axis
1/4-20 x 1/2” BHCS & Flat washer .017” thk.
• Move the axis to its center of travel.
• Mark the axis for quick return to center.
• Determine encoder cable exit direction and adjust (see page 3).
• Drill / tap the first end mounting hole / attach the spar.
• Align to within .010” TIR. to -A-, drill / tap second end hole.
• Attach the spar / align to within .010” TIR. to -A-.
11
ACU-RITE
®
Spar Installation Procedure
ENC 150
M4 x 8mm set screws
8-32 x 5/8” SHCS
(M4 x 16mm)
Do not tighten prior to adjusting
leveling set screws.
• Insert the encoder into the spar.
• Center the encoder from end to end with the spar.
• Lock in place by tightening the M4 set screws.
• Attach the bracket to the machine.
• Align the reading head mounting holes with the bracket holes.
• Attach head to bracket / Set leveling screws / Secure fasteners.
Alignment bracket
removal
Reading head bracket
(trim 8-32 screw to
length required)
Slide brackets away from reading
head and cable.
twist 45°
• To locate the reading head bracket, attach it to the reading head.
• Center the axis and mark the bracket mounting holes.
• Remove the bracket, drill / tap holes for 1/4-20 (M6).
ACU-RITE
®
• Slide the brackets away from the reading head.
• Remove the alignment brackets and save for future use.
12
ENC150
Checking Your Installation
These steps will confirm proper operation of your installation. The
Counting Test confirms proper electrical operation. The Repeatability
Test checks the installation integrity.
Counting Test:
• Configure the readout’s encoder and display resolution (see
manual).
• Move the axis and compare the display to the movement.
• Configure readout for sensing reference marks.
• Move each axis a minimum of 20mm (axis display should zero).
• Route the cables with slack loops to allow for axis motion.
• Secure excess cable by fastening with clips or ties.
• Attach the linear encoder connectors to the readout.
Repeatability Test:
• Locate an indicator on one end of the encoder and zero the
readout and indicator.
• Move the axis through the full travel and return to dial zero.
• Readout should read zero ± 1 count.
Counting Test
Repeatability Test
Readout
Place dial indicator at the end of the moving
component (scale assembly or reading head).
• Move the axis and compare the display to the movement.
• Move the axis 20mm (.79”) to check reference mark operation.
• Zero the display and indicator.
• Move axis to the end of it’s travel return to dial zero.
• Readout should read zero ± 1 count.
13
ACU-RITE
®
Electrical Shielding
ENC 150
Connect a ground wire from the terminal on the back of the readout
to the machine or earth ground. Attach a ground wire from the
machine to a solid earth ground.
With the encoder attached to the machine and the cable connected
to the readout, check shielding by measuring resistance between
connector housing and scale unit. Desired value: 1 Ω max.
ACU-RITE
®
14
ENC 150
If you experience difficulties with your installation, do the following
to determine the problem.
Checking the Readout
Difficulties on more than one axis are usually associated with the
readout. Follow these steps to determine if your difficulties are
associated with the readout:
• Insure that the linear encoder connectors are correctly seated.
• Swap linear encoder cables at the readout to see if the problem
is still shown in the same display.
• If the problem remains in the same display, the readout is in error.
• If the problem follows the connection change, the linear encoder
may be in error.
If the Readout is at fault, refer to “What to do” to arrange for the
parts necessary to repair your system. If a linear encoder appears
to be at fault, proceed with “Checking the Linear Encoders”.
Checking the Linear Encoders
Problems on a single axis are usually associated with the linear
encoder or its installation. Difficulties can be caused by improper
installation, loose or misaligned bracketry, or a damaged or
inoperable encoder.
Trouble Shooting
Follow these steps to determine the cause of your system difficulties:
• Confirm that your bracketry and installation does not interfere
with other machine structures through the entire length of the
linear encoder travel.
• Check for loose fasteners. If you find loose fasteners, first confirm
that the linear encoder is installed to the tolerances specified and
then retighten the fasteners as required.
• Confirm that the linear encoder is installed to the required
tolerances by checking the alignment tolerances specified on
Page 4. If the installation does not meet the tolerances, reinstall
the encoder according to the “Installation Procedure”.
• Perform a Repeatability Test as described on Page 11. If the
linear encoder is installed to the required tolerances, the bracketry
and encoder have been checked for interferences and loose
fasteners, and the encoder fails the repeatability test, the encoder
is likely at fault.
Do not attempt to repair the reading head or scale assembly. The
ENC 150 is field serviceable by assembly replacement only.
Attempts to repair the encoder can permanently damage it and void
the warranty.
What to do
If an ACU-RITE linear encoder or readout is found to be at fault,
please contact your Authorized ACU-RITE Distributor for instructions
prior to removing the encoders or readout .
15
ACU-RITE
®
Mechanical Specifications
ENC150
Mechanical Specifications
Resolution (µm)
Grating pitch (µm)
Scale medium
Digital
2
10
Analog
1
5
5
40
20
Light transmission through chrome-coated glass
Accuracy (@ 20° C)
µm, ±, in any 1000mm
3, 5
Max. slew speed (inches/sec)
40
≤ 0.75
Force to move reading head (lbs)
Operating Environment
Temperature
Relative Humidity
0° to 40°C
25% to 95% (non-condensing)
Storage Environment
Temperature
Humidity
-40° to 65°C
20% to 95% (non-condensing)
Weight w/ armor cable (lbs)
Connecting cable
armored or vinyl
1.4 + 0.05/in of measuring length
Length = 5, 10, and 15 ft,
Connector: DE-9P or Bendix PTO -GA-10-6P
Max. cable length (ft)
35
Measuring lengths (in)
2 - 120
Reference pulse interval
ACU-RITE
®
Distance or coded
16
ENC 150
Output Signals and Pin-Outs
Digital Differential
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
Pin 7
Pin 8
Pin 9
N/C
Green
Yellow
Blue
Red
White
Brown
Pink
Gray
N/C
Channel
A+
Channel
A-
Channel
B+
Channel
B-
Ground
Vcc, + 5.1
± 0.1 VDC @ 140mA max.
Channel
R+
Channel
R-
1
5
6 9
Analog Differential
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
Pin 7
Pin 8
Pin 9
White
Green
Yellow
Blue
Red
N/C
Brown
Pink
Gray
Ground
Channel
A+
Channel
A-
Channel
B+
Channel
B-
N/C
Vcc, + 5.0
± 0.1 VDC @ 80mA max.
Channel
R+
Channel
R-
Large key
A
B
Digital single ended
Pin A
Pin B
Green
Channel A
Pin C
Pin D
Pin E
Pin F
Blue
Brown
White
Drain
Pink
Channel B
Vcc, +5.1 + 0.1 VDC @
140mA max.
Common (power supply and
signal return)
Shield, reading head
casting ground
Channel R (Reference
Mark)
17
ACU-RITE
®
Electrical Specifications
Parameter
Output Signals
ENC150
Digital
IOH=(High level output
VOH=(High level output
360°
0°
1
Channel A+
0
1
Channel A0
90°
1
Channel B+
0
1
Channel B0
Analog
current) = 20mA
voltage) >2.5Vdc
0°
1
IµA Channel B
0
Channel R- 1
0
Channel A
Channel R+
90°
360°
IA, B:7-16 µApp
135° ± 20°
1 Count
IµA
IR:2-8 µApp
Channel R
360° ± 60°
IOL=(Low level output current) = 20mA
VOL=(Low level output voltage) < 0.5Vdc
Incremental signals
Square-wave voltage signals.
Channels A and B, in 90°
quadrature relationship
Signal levels
TTL-level
7-16µApp
w/1 K Ohm load
Reference Mark signals
Square-wave pulse
Differential current output
Signal level
TTL-level
2-8µApp
w/100 K Ohm load
Power Supply
ACU-RITE
®
5.1 ± 0.1 VDC @ 140 mA max.
18
Similar phasing, but differential
sinusoidal current output
5.1 ± 0.1 VDC @ 80 mA max.
ENC 150
ACU-RITE products and accessories are warranted against defects
in material and workmanship for a period of three years from the
date of purchase. ACU-RITE will, at its option and expense, repair
or replace any part of the ACU-RITE product which fails to meet
this warranty. This warranty covers both materials and factory labor.
In addition, authorized ACU-RITE distributors will provide field
service labor for a period of one-year at no charge. Notice of the
claimed defect must be received by ACU-RITE within the warranty
period.
This warranty applies only to products and accessories installed
and operated in accordance with this reference manual. ACU-RITE
shall have no obligation, with respect to any defect or other condition
caused in whole or in part by the customer's incorrect use, improper
maintenance, modification of the equipment, or by the repair or
maintenance of the product by any person except those deemed
qualified by ACU-RITE.
Warranty
Responsibility for loss of operation or diminished performance due
to conditions beyond ACU-RITE's control cannot be accepted by
ACU-RITE.
The foregoing warranty obligations are in lieu of all expressed or
implied warranties. ACU-RITE INCORPORATED shall not be liable
under any circumstances for consequential damages.
30 Day Red Carpet Warranty
All ACU-RITE products are covered by a 30-day Red Carpet
Warranty. If in the first 30 days this product fails for any reason,
repackage it in the original packaging materials and contact your
Authorized ACU-RITE Distributor for return procedures.
19
ACU-RITE
®
es
t
No
Precision Glass Scale Linear Encoders and
Readout Systems are manufactured in the USA
ACU-RITE IS AN
ISO 9001
CERTIFIED
MANUFACTURER
ACU-RITE INCORPORATED
ONE PRECISION WAY
MASON INDUSTRIAL PARK
JAMESTOWN, NEW YORK 14701
101000-170 EDITION D 8/98
PRINTED IN USA
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising