Biostar 945GC-M7TE User`s manual
945GC-M7 TE Setup Manual
FCC Information and Copyright
This equipment has been tested and found to comply with the limits of a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. There is no guarantee
that interference will not occur in a particular installation.
The vendor makes no representations or warranties with respect to the
contents here and specially disclaims any implied warranties of merchantability
or fitness for any purpose. Further the vendor reserves the right to revise this
publication and to make changes to the contents here without obligation to
notify any party beforehand.
Duplication of this publication, in part or in whole, is not allowed without first
obtaining the vendor’s approval in writing.
The content of this user’s manual is subject to be changed without notice and
we will not be responsible for any mistakes found in this user’s manual. All the
brand and product names are trademarks of their respective companies.
Table of Contents
Chapter 1: Introduction ........................................ 1
1.1
1.2
1.3
1.4
1.5
Before You Start ................................................................................ 1
Package Checklist ............................................................................. 1
Motherboard Features...................................................................... 2
Rear Panel Connectors ..................................................................... 3
Motherboard Layout......................................................................... 4
Chapter 2: Hardware Installation .......................... 5
2.1
2.2
2.3
2.4
Installing Central Processing Unit (CPU)....................................... 5
FAN Headers...................................................................................... 7
Installing System Memory ................................................................ 8
Connectors and Slots ....................................................................... 10
Chapter 3: Headers & Jumpers Setup .................. 12
3.1
3.2
How to Setup Jumpers .................................................................... 12
Detail Settings.................................................................................. 12
Chapter 4: Useful Help ........................................ 19
4.1
4.2
4.3
4.4
Driver Installation Note.................................................................. 19
Award BIOS Beep Code .................................................................. 20
Extra Information............................................................................ 20
Troubleshooting............................................................................... 21
Chapter 5: WarpSpeeder™ III ............................. 22
5.1
5.2
5.3
5.4
Introduction...................................................................................... 22
System Requirement ....................................................................... 22
Installation ....................................................................................... 23
WarpSpeeder™ III............................................................................. 24
Appendencies: SPEC In Other Language .............. 30
German.................................................................................................................. 30
France .................................................................................................................... 32
Italian..................................................................................................................... 34
Spanish ................................................................................................................... 36
Portuguese ............................................................................................................ 38
Polish...................................................................................................................... 40
Russian ................................................................................................................... 42
Arabic..................................................................................................................... 44
Japanese ................................................................................................................ 46
945GC-M7 TE
CHAPTER 1: INTRODUCTION
1.1
BEFORE YOU START
Thank you for choosing our product. Before you start installing the
motherboard, please make sure you follow the instructions below:
„
„
„
„
„
„
1.2
Prepare a dry and stable working environment with
sufficient lighting.
Always disconnect the computer from power outlet
before operation.
Before you take the motherboard out from anti-static
bag, ground yourself properly by touching any safely
grounded appliance, or use grounded wrist strap to
remove the static charge.
Avoid touching the components on motherboard or the
rear side of the board unless necessary. Hold the board
on the edge, do not try to bend or flex the board.
Do not leave any unfastened small parts inside the
case after installation. Loose parts will cause short
circuits which may damage the equipment.
Keep the computer from dangerous area, such as heat
source, humid air and water.
PACKAGE CHECKLIST
HDD Cable X 1
Rear I/O Panel for ATX Case X 1
Installation Guide X 1
Fully Setup Driver CD X 1 (full version manual files inside)
Serial ATA Cable X 1
FDD Cable X 1 (optional)
Serial ATA Power Cable X 1 (optional)
USB 2.0 Cable X1 (optional)
S/PDIF out Cable X 1 (optional)
Note: The package contents may differ by area or your motherboard version.
1
Motherboard Manual
1.3
MOTHERBOARD FEATURES
SPEC
LGA 775
Intel Core2Duo / Pentium 4 / Pentium D /
CPU
Celeron D / Celeron 4xx processor up to 3.8
GHz *It is recommended to use processors
with 95W power consumption.
FSB
Chipset
Graphics
Super I/O
Supports Hyper-Threading
Execute Disable Bit
Enhanced Intel SpeedStep
Extended Memory 64 Technology
533 / 800 / 1066 / 1333 MHz
Intel 945GC
Intel ICH7
Intel GMA 950
Max Shared Video Memory is 224MB
ITE IT8712F
Environment Control initiatives,
Provides the most commonly used legacy
H/W Monitor
Super I/O functionality.
Fan Speed Controller
Low Pin Count Interface
ITE's "Smart Guardian" function
DIMM Slots x 2
Main
Memory
Each DIMM supports 256/512MB & 1GB
DDR2
Dual Channel Mode DDR2 memory module
Registered DIMM and ECC DIMM is not supported
Max Memory Capacity 2GB
Supports DDR2 400 / 533 / 667
IDE
Integrated IDE Controller
SATA
Integrated Serial ATA Controller
LAN
Atheros L2
Sound
Codec
2
supports PIO Mode 0~4,
Data transfer rates up to 3.0 Gb/s.
SATA Version 2.0 specification compliant.
10 / 100 Mb/s auto negotiation
Half / Full duplex capability
5.1 channels audio out
ALC662
PCI Express x16 slot
Slots
Ultra DMA 33 / 66 / 100 Bus Master Mode
High-Definition Audio support
x1
Supports PCI-E x16 expansion cards
PCI Express x1 slot
x1
Supports PCI-E x1 expansion cards
PCI slot
x2
Supports PCI expansion cards
On Board
Floppy connector
x1
Each connector supports 2 Floppy drives
Connector
IDE Connector
x1
Each connector supports 2 IDE device
Printer Port Connector
x1
Each connector supports 1 Printer port
SATA Connector
x4
Each connector supports 1 SATA devices
945GC-M7 TE
SPEC
Back Panel
I/O
Board Size
Front Panel Connector
x1
Supports front panel facilities
Front Audio Connector
x1
Supports front panel audio function
CD-in Connector
x1
Supports CD audio-in function
S/PDIF out connector
x1
Supports digital audio out function
CPU Fan header
x1
CPU Fan power supply (with Smart Fan function)
System Fan header
x1
System Fan Power supply
Clear CMOS header
x1
Restore CMOS data to factory default
USB connector
x2
Each connector supports 2 front panel USB ports
Power Connector (24pin)
x1
Connects to Power supply
Power Connector (4pin)
x1
Connects to Power supply
PS/2 Keyboard
x1
Connects to PS/2 Keyboard
PS/2 Mouse
x1
Connects to PS/2 Mouse
Serial Port
x1
Provide RS-232 Serial connection
VGA port
x1
Connects to monitor.
LAN port
x1
Connects to RJ-45 ethernet cable
USB Port
x4
Connects to USB devices
Audio Jack
x3
Provide Audio-In/Out and microphone connection
190 (W) x 239 (L) mm
Micro ATX form Factor
Biostar Reserves the right to add or remove support
OS Support Windows 2000 / XP / VISTA
1.4
for any OS with or without notice.
REAR PANEL CONNECTORS
PS/2
Mouse
LAN
Line In/
Sur round
Line Out
Mic In 1/
Bass/ Center
PS/2
Keyboar d
COM1
VGA1
USBX2
USBX2
Since the audio chip supports High Definition Audio Specification, the function of each audio
jack can be defined by software. The input / output function of each audio jack listed above
represents the default setting. However, when connecting external microphone to the audio
port, please use the Line In (Blue) and Mic In (Pink) audio jack.
3
Motherboard Manual
1.5
MOTHERBOARD LAYOUT
JCFAN1
JKBMS1
COM1
JCOM1
LGA775
JATXPWR1
CPU1
JUSB2
DDR2_B1
DDR2_A1
JUSBV1
Intel
945GC
JRJ45USB1
IDE1
JVGA1
JATXPWR2
JSFAN1
JAUDIO1
DVIJ1(Optional)
PEX16_1
PEX1_1
BAT1
LAN
JCMOS1
SATA4
JCDIN1
JSPDIF_OUT1
PCI2
SATA1
Codec
JPRNT1
FDD1
JAUDIOF1
Note: ■ represents the 1st pin.
4
SATA2
Intel
ICH7
PCI1
SATA3
BIOS
JUSBV2
JUSB3
JUSB4
JPANEL1
945GC-M7 TE
CHAPTER 2: HARDWARE INSTALLATION
2.1
INSTALLING CENTRAL PROCESSING UNIT (CPU)
Special Notice:
Remove Pin Cap before installation, and make good preservation
for future use. When the CPU is removed, cover the Pin Cap on the
empty socket to ensure pin legs won’t be damaged.
Pin-Cap
Step 1: Pull the socket locking lever out from the socket and then raise
the lever up to a 90-degree angle.
5
Motherboard Manual
Step 2: Look for the triangular cut edge on socket, and the golden dot on
CPU should point forwards this triangular cut edge. The CPU will
fit only in the correct orientation.
Step 2-1:
Step 2-2:
Step 3: Hold the CPU down firmly, and then lower the lever to locked
position to complete the installation.
Step 4: Put the CPU Fan and heatsink assembly on the CPU and buckle it
on the retention frame. Connect the CPU FAN power cable into
the JCFAN1. This completes the installation.
6
945GC-M7 TE
2.2
FAN HEADERS
These fan headers support cooling-fans built in the computer. The fan
cable and connector may be different according to the fan manufacturer.
Connect the fan cable to the connector while matching the black wire to
pin#1.
JCFAN1: CPU Fan Header
1
4
Assignment
Ground
+12V
FAN RPM rate
sense
Smart Fan
Control
Pin
1
2
3
4
JSFAN1: System Fan Header
Pin
1
3
1
2
3
Assignment
Ground
+12V
FAN RPM rate
sense
Note:
The JCFAN1 and JSFAN1 support 4-pin and 3-pin head connector. When connecting
with wires onto connectors, please note that the red wire is the positive and should be
connected to pin#2, and the black wire is Ground and should be connected to GND.
7
Motherboard Manual
2.3
INSTALLING SYSTEM MEMORY
8
DDR2_B1
DDR2_A1
A. DDR2 Module
1.
Unlock a DIMM slot by pressing the retaining clips outward. Align a
DIMM on the slot such that the notch on the DIMM matches the
break on the Slot.
2.
Insert the DIMM vertically and firmly into the slot until the retaining
chip snap back in place and the DIMM is properly seated.
945GC-M7 TE
B. Memory Capacity
DIMM Socket
Location
DDR2 Module
Total Memory Size
DDR2_A1
DDR2_B1
256MB/512MB/1GB *1
256MB/512MB/1GB *1
Max memory 2GB.
C. Dual Channel Memory Installation
To trigger the Dual Channel function of the motherboard, the memory module
must meet the following requirements:
Install memory module of the same density in pairs, shown in the following
table.
Dual Channel Status DDR2_A1 DDR2_B1
Disabled
O
X
Disabled
X
O
Enabled
O
O
(O means memory installed, X means memory not installed.)
The DRAM bus width of the memory module must be the same (x8 or
x16)
D. FSB Supporting Table
According to the FSB frequency of the installed CPU, the motherboard could
support DDR2 400/533/667 modules. Please refer to the table below to find
out the proper RAM module that fits the FSB of the installed CPU.
FSB of CPU
DDR2 Module
DDR2 400
DDR2 533
DDR2 667
DDR2 800(compatible)
FSB 533
FSB 800
FSB 1066
FSB1333
O
O
O
O(667)
O
O
O
O(667)
O
O
O
O(667)
X
O(500)
O
O(667)
(O means supported, X means not supported.)
9
Motherboard Manual
2.4 CONNECTORS AND SLOTS
FDD1: Floppy Disk Connector
The motherboard provides a standard floppy disk connector that supports 360K,
720K, 1.2M, 1.44M and 2.88M floppy disk types. This connector supports the
provided floppy drive ribbon cables.
33
1
34
2
IDE1: Hard Disk Connectors
The motherboard has a 32-bit Enhanced PCI IDE Controller that provides PIO
Mode 0~4, Bus Master, and Ultra DMA 33/66/100 functionality.
The IDE connector can connect a master and a slave drive, so you can connect
up to two hard disk drives.
40
2
10
39
1
945GC-M7 TE
PEX16_1: PCI-Express x16 Slot
-
PCI-Express 1.0a compliant.
Maximum theoretical realized bandwidth of 4GB/s simultaneously per
direction, for an aggregate of 8GB/s totally.
PEX1_1: PCI-Express x1 Slot
-
PCI-Express 1.0a compliant.
Data transfer bandwidth up to 250MB/s per direction; 500MB/s in total.
PCI-Express supports a raw bit-rate of 2.5Gb/s on the data pins.
2X bandwidth over the traditional PCI architecture.
PEX16_1
PEX1_1
PCI1~PCI2: Peripheral Component Interconnect Slots
The motherboard is equipped with 2 standard PCI slots. PCI stands for
Peripheral Component Interconnect, and it is a bus standard for expansion
cards. This PCI slot is designated as 32 bits.
PCI1
PCI2
11
Motherboard Manual
CHAPTER 3: HEADERS & JUMPERS SETUP
3.1
HOW TO SETUP JUMPERS
The illustration shows how to set up jumpers. When the jumper cap is
placed on pins, the jumper is “close”, if not, that means the jumper is
“open”.
Pin opened
3.2
Pin closed
Pin1-2 closed
DETAIL SETTINGS
JPANEL1: Front Panel Header
This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, Sleep
button, and speaker connections. It allows user to connect the PC case’s front
panel switch functions.
SLP
PWR_LED
ON/OFF
++-
9
1
+ SPK
Pin
1
2
3
4
5
6
7
8
12
Assignment
+5V
N/A
N/A
Speaker
HDD LED (+)
HDD LED (-)
Ground
Reset control
Function
Speaker
Connector
Hard drive
LED
Reset button
Pin
9
10
11
12
13
14
15
16
16
8
RST
HLED
Assignment
Sleep control
Ground
N/A
Power LED (+)
Power LED (+)
Power LED (-)
Power button
Ground
Function
Sleep button
N/A
Power LED
Power-on button
945GC-M7 TE
JATXPWR1: ATX Power Source Connector
This connector allows user to connect 24-pin power connector on the ATX
power supply.
12
24
1
13
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Assignment
+3.3V
+3.3V
Ground
+5V
Ground
+5V
Ground
PW_OK
Standby
Voltage +5V
+12V
+12V
2 x 12 Detect
+3.3V
-12V
Ground
PS_ON
Ground
Ground
Ground
-5V
+5V
+5V
+5V
Ground
JATXPWR2: ATX Power Source Connector
By connecting this connector, it will provide +12V to CPU power circuit.
4
3
1
2
Pin
1
2
3
4
Assignment
+12V
+12V
Ground
Ground
13
Motherboard Manual
JUSB3/JUSB4: Headers for USB 2.0 Ports at Front Panel
This motherboard provides 2 USB 2.0 headers, which allows user to connect
additional USB cable on the PC front panel, and also can be connected with
internal USB devices, like USB card reader.
JUSB3
JUSB4
9
1
10
2
Pin
1
2
3
4
5
6
7
8
9
10
Assignment
+5V (fused)
+5V (fused)
USBUSBUSB+
USB+
Ground
Ground
Key
NC
SATA1~SATA4: Serial ATA Connectors
The motherboard has a PCI to SATA Controller with 4 channels SATA interface,
it satisfies the SATA 2.0 spec and with transfer rate of 3Gb/s.
Pin
SATA4
SATA3
SATA2
SATA1
1
14
4
7
Assignment
1
Ground
2
TX+
3
TX-
4
Ground
5
RX-
6
RX+
7
Ground
945GC-M7 TE
JSPDIF_OUT1: Digital Audio out Connectors
This connector allows user to connect the PCI bracket SPDIF output header.
Pin
1
2
3
3
Assignment
+5V
SPDIF_OUT1
Ground
1
JAUDIOF1: Front Panel Audio Header
This header allows user to connect the front audio output cable with the PC front
panel. It will disable the output on back panel audio connectors.
9
1
10
2
Pin
1
2
3
4
5
6
7
8
9
10
Assignment
Mic Left in
Ground
Mic Right in
GPIO
Right line in
Jack Sense
Front Sense
Key
Left line in
Jack Sense
15
Motherboard Manual
JCDIN1: CD-ROM Audio-in Connector
This connector allows user to connect the audio source from the variaty devices,
like CD-ROM, DVD-ROM, PCI sound card, PCI TV turner card etc..
Pin
1
2
3
4
4
Assignment
Left Channel
Input
Ground
Ground
Right Channel
Input
1
JCMOS1: Clear CMOS Header
By placing the jumper on pin2-3, it allows user to restore the BIOS safe setting
and the CMOS data, please carefully follow the procedures to avoid damaging
the motherboard.
1
3
Pin 1-2 Close:
Normal Operation (Default).
1
3
1
3
Pin 2-3 Close:
Clear CMOS data.
※ Clear CMOS Procedures:
16
1.
2.
3.
4.
5.
Remove AC power line.
Set the jumper to “Pin 2-3 close”.
Wait for five seconds.
Set the jumper to “Pin 1-2 close”.
Power on the AC.
6.
Reset your desired password or clear the CMOS data.
945GC-M7 TE
DVIJ1: Connector for DVI Daughter Card Adapter (Optional)
This connector is for the specific DVI adapter, which is equipped with a DVI-D
connector. With the adapter you can use the DVI-D interface for a better
display quality. Moreover, the original D-SUB and the additional DVI-D can be
utilized simultaneously, so two panels can disaply simultaneously.
27
1
28
2
JUSBV1/JUSBV2: Power Source Headers for USB Ports
Pin 1-2 Close:
JUSBV1: +5V for USB ports at JRJ45USB1/JUSB2.
JUSBV2: +5V for USB ports at front panel (JUSB3/JUSB4).
Pin 2-3 Close:
JUSBV1: USB ports at JRJ45USB1/JUSB2 are powered by +5V standby
voltage.
JUSBV2: USB ports at front panel (JUSB3/JUSB4) are powered by +5V
standby voltage.
JUSBV1
3
3
1
Pin 1-2 close
1
3
1
JUSBV2
3
1
Pin 2-3 close
Note:
In order to support this function “Power-On system via USB device,” “JUSBV1/ JUSBV2”
jumper cap should be placed on Pin 2-3 individually.
17
Motherboard Manual
JPRNT1: Printer Port Connector
This header allows you to connector printer on the PC.
25
1
2
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
18
Assignment
-Strobe
-ALF
Data 0
-Error
Data 1
-Init
Data 2
-Scltin
Data 3
Ground
Data 4
Ground
Data 5
Pin
14
15
16
17
18
19
20
21
22
23
24
25
26
Assignment
Ground
Data 6
Ground
Data 7
Ground
-ACK
Ground
Busy
Ground
PE
Ground
SCLT
Key
945GC-M7 TE
CHAPTER 4: USEFUL HELP
4.1
DRIVER INSTALLATION NOTE
After you installed your operating system, please insert the Fully Setup
Driver CD into your optical drive and install the driver for better system
performance.
You will see the following window after you insert the CD
The setup guide will auto detect your motherboard and operating system.
Note:
If this window didn’t show up after you insert the Driver CD, please use file browser to
locate and execute the file SETUP.EXE under your optical drive.
A. Driver Installation
To install the driver, please click on the Driver icon. The setup guide will
list the compatible driver for your motherboard and operating system.
Click on each device driver to launch the installation program.
B. Software Installation
To install the software, please click on the Software icon. The setup guide
will list the software available for your system, click on each software title
to launch the installation program.
C. Manual
Aside from the paperback manual, we also provide manual in the Driver
CD. Click on the Manual icon to browse for available manual.
Note:
You will need Acrobat Reader to open the manual file. Please download the latest version
of Acrobat Reader software from
http://www.adobe.com/products/acrobat/readstep2.html
19
Motherboard Manual
4.2
AWARD BIOS BEEP CODE
Beep Sound
Meaning
One long beep followed by two short
beeps
Video card not found or video card
memory bad
High-low siren sound
CPU overheated
System will shut down automatically
One Short beep when system boot-up
Long beeps every other second
No error found during POST
No DRAM detected or install
4.3
EXTRA INFORMATION
CPU Overheated
If the system shutdown automatically after power on system for
seconds, that means the CPU protection function has been activated.
When the CPU is over heated, the motherboard will shutdown
automatically to avoid a damage of the CPU, and the system may not
power on again.
In this case, please double check:
1. The CPU cooler surface is placed evenly with the CPU surface.
2. CPU fan is rotated normally.
3. CPU fan speed is fulfilling with the CPU speed.
After confirmed, please follow steps below to relief the CPU
0protection function.
1. Remove the power cord from power supply for seconds.
2. Wait for seconds.
3. Plug in the power cord and boot up the system.
Or you can:
1. Clear the CMOS data.
(See “Close CMOS Header: JCMOS1” section)
2. Wait for seconds.
3. Power on the system again.
20
945GC-M7 TE
4.4
TROUBLESHOOTING
Probable
Solution
1.
No power to the system at all
1.
Make sure power cable is
Power light don’t illuminate, fan
securely plugged in.
inside power supply does not turn 2.
Replace cable.
on.
3.
Contact technical support.
2.
Indicator light on keyboard does
not turn on.
System inoperative. Keyboard lights
Using even pressure on both ends of
are on, power indicator lights are lit,
the DIMM, press down firmly until the
and hard drive is spinning.
module snaps into place.
System does not boot from hard disk
1.
Check cable running from disk to
drive, can be booted from optical drive.
disk controller board. Make sure
both ends are securely plugged
in; check the drive type in the
standard CMOS setup.
2.
Backing up the hard drive is
extremely important. All hard
disks are capable of breaking
down at any time.
System only boots from optical drive.
1.
Back up data and applications
Hard disk can be read and applications
files.
can be used but booting from hard disk 2.
Reformat the hard drive.
is impossible.
Re-install applications and data
using backup disks.
Screen message says “Invalid
Review system’s equipment. Make sure
Configuration” or “CMOS Failure.”
correct information is in setup.
Cannot boot system after installing
1.
Set master/slave jumpers
second hard drive.
correctly.
2.
Run SETUP program and select
correct drive types. Call the drive
manufacturers for compatibility
with other drives.
21
Motherboard Manual
CHAPTER 5: WARPSPEEDER™ III
5.1
INTRODUCTION
[WarpSpeeder™ III], a new powerful control utility, features three
user-friendly functions including Overclock Manager, Overvoltage
Manager, and Hardware Monitor.
With the Overclock Manager, users can easily adjust the frequency they
prefer or they can get the best CPU performance with just one click. The
Overvoltage Manager, on the other hand, helps to power up CPU core
voltage and Memory voltage. The cool Hardware Monitor smartly indicates
the temperatures, voltage and CPU fan speed as well as the chipset
information. Also, in the About panel, you can get detail descriptions about
BIOS model and chipsets. In addition, the frequency status of CPU,
memory, VGA and PCI along with the CPU speed are synchronically
shown on our main panel.
Moreover, to protect users' computer systems if the setting is not
appropriate when testing and results in system fail or hang,
[WarpSpeeder™ III] technology assures the system stability by
automatically rebooting the computer and then restart to a speed that is
either the original system speed or a suitable one.
5.2
SYSTEM REQUIREMENT
OS Support: Windows 98 SE, Windows Me, Windows 2000, Windows XP,
Windows Vista
DirectX: DirectX 8.1 or above. (The Windows XP operating system
includes DirectX 8.1. If you use Windows XP, you do not need to install
DirectX 8.1.)
22
945GC-M7 TE
5.3
INSTALLATION
1. Execute the setup execution file, and then the following dialog will pop
up. Please click “Next” button and follow the default procedure to
install.
2. When you see the following dialog in setup procedure, it means setup
is completed. Click “Finish” button.
Usage:
The following figures are only for reference, the screen printed in this
user manual will change according to your motherboard on hand.
23
Motherboard Manual
5.4
WARPSPEEDER™ III
1. Desktop Icon
After the [WarpSpeeder™ III] has been installed, a [WarpSpeeder™ III]
icon will appear on the desktop, just like the icon shown below.
Now you can launch the [WarpSpeeder™ III] utility simply by
double-clicking the desktop icon.
2. Main Panel
If you double-click the desktop icon, [WarpSpeeder™ III] will be
launched. Please refer to the following figure; the utility’s first window
you will see is Main Panel.
Main Panel contains features as follows:
24
a.
Display the CPU Speed, CPU external clock, Memory clock, VGA
clock, and PCI clock information.
b.
Contains About, Voltage/Overclock, and Hardware Monitor
Buttons for invoking respective panels. The On/Off button is for
closing the program.
945GC-M7 TE
3. Overclock/Overvoltage Panel
Click the Overclock/Overvoltage button in the Main Panel, the button
will be highlighted and the Overclock/Overvoltage Panel will show
up as the following figure. As you can see, the Overclock Panel is
on the right side, and the Overvoltage Panel is on the left side.
25
Motherboard Manual
Overclock Panel contains these features:
a.
“Auto-Overclock”:
User can click this button and [WarpSpeeder™ III] will set the best
and stable performance and frequency automatically. A warning
dialog as below will show up to notify you that the system may
become unstable, click on “OK” to proceed.
Then [WarpSpeeder™ III] utility will execute a series of testing
until system fail. Then system will do fail-safe reboot by using
Watchdog function. After reboot, launch the [WarpSpeeder™ III]
utility again and the utility will load the previously verified best and
stable frequency.
b.
“Verify”:
If you use the “Manual Adjust” bar to adjust the CPU frequency,
then you can click this button and [WarpSpeeder™ III] will proceed
a testing for current frequency. If the testing is ok, then the current
frequency will be saved into system registry. If the testing fails,
system will do a fail-safe rebooting. After reboot, the
[WarpSpeeder™ III] utility will restore to the hardware default
setting.
Warning:
Manually overclock is potentially dangerous, especially when the
overclocking percentage is over 110 %. We strongly recommend you
verify every speed you overclock by click the Verify button. Or, you can
just click Auto overclock button and let [WarpSpeeder™ III]
automatically gets the best result for you.
26
c.
“V3 Engine”/“V6 Engine”/“V9 Engine”:
Provide user the ability to do real-time overclock adjustment.
d.
“Recovery”:
Click this button and the [WarpSpeeder™ III] utility will restore all
values to the hardware default setting.
945GC-M7 TE
Overvoltage Panel contains these features:
a.
b.
“CPU Voltage”:
This function allows user to adjust CPU voltage.
increase or “-“ to decrease the CPU voltage.
Click on “+” to
“Memory Voltage”:
This function allows user to adjust Memory voltage.
to increase or “-“ to decrease the Memory voltage.
Click on “+”
4. Hardware Monitor Panel
Click the Hardware Monitor button in Main Panel, the button will be
highlighted and the Hardware Monitor panel will show up as the
following figure.
In this panel, you can get the real-time status information of your
system. The information will be refreshed every 1 second.
27
Motherboard Manual
5. About Panel
Click the “about” button in Main Panel, the button will be highlighted
and the About Panel will show up as the following figure.
In this panel, you can get model name and detail information in hints
of all the chipset that are related to overclocking. You can also get
the the version number of [WarpSpeeder™ III] utility.
Note:
Because the overclock, overvoltage, and hardware monitor features
are controlled by several separate chipset, [WarpSpeeder™ III]
divide these features to separate panels. If one chipset is not on
board, the correlative button in Main panel will be disabled, but will
not interfere other panels’ functions. This property can make
[WarpSpeeder™ III] utility more robust.
28
945GC-M7 TE
This page is intentionally left blank.
29
Motherboard Manual
APPENDENCIES: SPEC IN OTHER LANGUAGE
GERMAN
Spezifikationen
LGA 775
Intel Core2Duo / Pentium 4 / Pentium D /
CPU
Unterstützt Hyper-Threading
Celeron D / Celeron 4xx Prozessoren mit bis zu Execute Disable Bit
3,8 GHz
Enhanced Intel SpeedStep®
*It is recommended to use processors with
Extended Memory 64 Technology
95W power consumption.
FSB
Chipsatz
Grafik
Super E/A
533 / 800 / 1066 / 1333 MHz
Intel 945GC
Intel ICH7
Intel GMA 950
Max. 224MB gemeinsam benutzter Videospeicher
ITE 8712F
Umgebungskontrolle,
Bietet die häufig verwendeten alten Super
Hardware-Überwachung
E/A-Funktionen.
Lüfterdrehzahl-Controller
Low Pin Count-Schnittstelle
"Smart Guardian"-Funktion von ITE
DDR2 DIMM-Steckplätze x 2
Arbeitsspeich
er
Jeder DIMM unterstützt 256/512MB & 1GB
Dual-Kanal DDR2 Speichermodul
DDR2
registrierte DIMMs. ECC DIMMs werden nicht
Max. 2GB Arbeitsspeicher
unterstützt.
Unterstützt DDR2 400 / 533 / 667
IDE
Integrierter IDE-Controller
SATA
Integrierter Serial ATA-Controller
LAN
Atheros L2
Ultra DMA 33 / 66 / 100 Bus Master-Modus
Unterstützt PIO-Modus 0~4
Datentransferrate bis zu 3Gb/s
Konform mit der SATA-Spezifikation Version 2.0
10 / 100 Mb/s Auto-Negotiation
Halb-/ Vollduplex-Funktion
5.1-Kanal-Audioausgabe
Audio-Codec ALC662
Steckplätze
30
Unterstützt High-Definition Audio
PCI Express x16 Steckplatz
x1
PCI Express x 1-Steckplatz
x1
PCI-Steckplatz
x2
945GC-M7 TE
Spezifikationen
Diskettenlaufwerkanschluss
x1
Jeder Anschluss unterstützt 2 Diskettenlaufwerke
IDE-Anschluss
x1
Jeder Anschluss unterstützt 2 IDE-Laufwerke
Druckeranschluss Anschluss
x1
Jeder Anschluss unterstützt 1 Druckeranschluss
SATA-Anschluss
x4
Jeder Anschluss unterstützt 1 SATA-Laufwerk
Fronttafelanschluss
x1
Unterstützt die Fronttafelfunktionen
Front-Audioanschluss
x1
Unterstützt die Fronttafel-Audioanschlussfunktion
CD-IN-Anschluss
x1
Unterstützt die CD Audio-In-Funktion
x1
Unterstützt die digitale Audioausgabefunktion
Onboard-Ans S/PDIF-Ausgangsanschluss
chluss
Rückseiten-E
/A
CPU-Lüfter-Sockel
x1
System-Lüfter-Sockel
x1
"CMOS löschen"-Sockel
x1
USB-Anschluss
x2
Stromanschluss (24-polig)
x1
Stromanschluss (4-polig)
x1
PS/2-Tastatur
x1
PS/2-Maus
x1
Serieller Anschluss
x1
VGA-Anschluss
x1
LAN-Anschluss
x1
USB-Anschluss
x4
Audioanschluss
x3
CPU-Lüfterstromversorgungsanschluss (mit
Smart Fan-Funktion)
System-Lüfter-Stromversorgungsanschluss
Jeder Anschluss unterstützt 2
Fronttafel-USB-Anschlüsse
Platinengröße 190 mm (B) X 239 mm (L)
OS-Unterstüt
zung
Biostar behält sich das Recht vor, ohne
Windows 2000 / XP / VISTA
Ankündigung die Unterstützung für ein
Betriebssystem hinzuzufügen oder zu entfernen.
31
Motherboard Manual
FRANCE
SPEC
LGA 775
Prend en charge les technologies
Processeurs Intel Core2Duo / Pentium 4 /
UC
Pentium D / Celeron D / Celeron 4xx jusqu'à 3,8
GHz
*It is recommended to use processors with 95W
power consumption.
Hyper-Threading
d'exécution de bit de désactivation
Intel SpeedStep® optimisée
de mémoire étendue 64
Bus frontal 533 / 800 / 1066 / 1333 MHz
Chipset
Intel 945GC
Intel ICH7
Graphiques Intel GMA 950
Super E/S
Mémoire vidéo partagée maximale de 224 Mo
ITE 8712F
Initiatives de contrôle environnementales,
Fournit la fonctionnalité de Super E/S
Moniteur de matériel
patrimoniales la plus utilisée.
Contrôleur de vitesse de ventilateur
Interface à faible compte de broches
Fonction "Gardien intelligent" de l'ITE
Fentes DDR2 DIMM x 2
Mémoire
principale
Chaque DIMM prend en charge des DDR2 de
256/512 Mo et 1Go
charge
Prend en charge la DDR2 400 / 533 / 667
Contrôleur IDE intégré
SATA
Contrôleur Serial ATA intégré :
LAN
Atheros L2
Mode principale de Bus Ultra DMA 33 / 66 / 100
Prend en charge le mode PIO 0~4,
Taux de transfert jusqu'à 3 Go/s.
Conforme à la spécification SATA Version 2.0
10 / 100 Mb/s négociation automatique
Half / Full duplex capability
Sortie audio à 5.1 voies
Codec audio ALC662
PCI Express x16 Steckplatz
Fentes
Connecteur
embarqué
32
Les DIMM à registres et DIMM avec code
correcteurs d'erreurs ne sont pas prises en
Capacité mémoire maximale de 2 Go
IDE
Module de mémoire DDR2 à mode à double voie
Prise en charge de l'audio haute définition
x1
PCI Express x1 Steckplatz
x1
Fente PCI
x2
Connecteur de disquette
x1
Connecteur IDE
x1
Chaque connector prend en charge 2 lecteurs de
disquettes
Chaque connecteur prend en charge 2
périphériques IDE
945GC-M7 TE
SPEC
Connecteur de Port d'imprimante
x1
Connecteur SATA
x4
Connecteur du panneau avant
x1
Connecteur Audio du panneau avant
x1
Connecteur d'entrée CD
x1
Connecteur de sortie S/PDIF
x1
Embase de ventilateur UC
x1
Embase de ventilateur système
x1
Embase d'effacement CMOS
x1
Connecteur USB
x2
Connecteur d'alimentation (24 broches)
x1
Connecteur d'alimentation (4 broches)
x1
Clavier PS/2
x1
Souris PS/2
x1
E/S du
Port série
x1
panneau
Port VGA
x1
arrière
Port LAN
x1
Port USB
x4
Fiche audio
x3
Dimensions
de la carte
Chaque connector prend en charge 1 Port
d'imprimante
Chaque connecteur prend en charge 1
périphérique SATA
Prend en charge les équipements du panneau
avant
Prend en charge la fonction audio du panneau
avant
Prend en charge la fonction d'entrée audio de CD
Prend en charge la fonction de sortie audio
numérique
Alimentation électrique du ventilateur UC (avec
fonction de ventilateur intelligent)
Alimentation électrique du ventilateur système
Chaque connecteur prend en charge 2 ports USB
de panneau avant
190mm (l) X 239 mm (H)
Support SE Windows 2000 / XP / VISTA
Biostar se réserve le droit d'ajouter ou de
supprimer le support de SE avec ou sans préavis.
33
Motherboard Manual
ITALIAN
SPECIFICA
LGA 775
Processore Intel Core2Duo / Pentium 4 /
CPU
Supporto di Hyper-Threading
Pentium D / Celeron D / Celeron 4xx fino a Execute Disable Bit
3.8 GHz
Enhanced Intel SpeedStep®
*It is recommended to use processors with 95W Tecnologia Extended Memory 64
power consumption.
FSB
Chipset
Grafica
Super I/O
533 / 800 / 1066 / 1333 MHz
Intel 945GC
Intel ICH7
Intel GMA 950
La memoria video condivisa massima è di 224MB
ITE 8712F
Funzioni di controllo dell’ambiente:
Fornisce le funzionalità legacy Super I/O
Monitoraggio hardware
usate più comunemente.
Controller velocità ventolina
Interfaccia LPC (Low Pin Count)
Funzione "Smart Guardian" di ITE
Alloggi DIMM DDR2 x 2
Memoria
principale
Ciascun DIMM supporta DDR2 256/512MB Modulo di memoria DDR2 a canale doppio
e 1GB
DIMM registrati e DIMM ECC non sono
Capacità massima della memoria 2GB
supportati
Supporto di DDR2 400 / 533 / 667
IDE
Modalità Bus Master Ultra DMA 33 / 66 / 100
Controller IDE integrato
Supporto modalità PIO Mode 0-4
Velocità di trasferimento dei dati fino a 3
SATA
Controller Serial ATA integrato
Gb/s.
Compatibile specifiche SATA Versione 2.0.
LAN
Codec
audio
Alloggi
34
Negoziazione automatica 10 / 100 Mb/s
Atheros L2
Capacità Half / Full Duplex
Uscita audio 5.1 canali
ALC662
Supporto audio High-Definit ion (HD)
Fente PCI Express x16
x1
Fente PCI Express x1
x1
Alloggio PCI
x2
945GC-M7 TE
SPECIFICA
Connettori
su scheda
Connettore floppy
x1
Ciascun connettore supporta 2 unità Floppy
Connettore IDE
x1
Ciascun connettore supporta 2 unità IDE
Connettore Porta stampante
x1
Connettore SATA
x4
Ciascun connettore supporta 1 unità SATA
Connettore pannello frontale
x1
Supporta i servizi del pannello frontale
Connettore audio frontale
x1
Supporta la funzione audio pannello frontale
Connettore CD-in
x1
Supporta la funzione input audio CD
Connettore output SPDIF
x1
Supporta la funzione d’output audio digitale
Collettore ventolina CPU
x1
Collettore ventolina sistema
x1
Collettore cancellaz ione CMOS
x1
Connettore USB
x2
Connettore alimentazione (24 pin)
x1
Connettore alimentazione (4 pin)
x1
Tastiera PS/2
x1
Mouse PS/2
x1
I/O
Porta seriale
x1
pannello
Porta VGA
x1
posteriore Porta LAN
x1
Porta USB
x4
Connettore audio
x3
Dimension
i scheda
supportati
stampante
Alimentazione ventolina CPU (con funzione
Smart Fan)
Alimentazione ventolina di sistema
Ciascun connettore supporta 2 porte USB
pannello frontale
190 mm (larghezza) x 239 mm (altezza)
Sistemi
operativi
Ciascun connettore supporta 1 Porta
Biostar si riserva il diritto di aggiungere o
Windows 2000 / XP / VISTA
rimuovere il supporto di qualsiasi sistema
operativo senza preavviso.
35
Motherboard Manual
SPANISH
Especificación
LGA 775
CPU
Procesador Intel Core2Duo / Pentium 4 /
Admite Hyper-Threading
Pentium D / Celeron D / Celeron 4xx hasta
Bit de deshabilitación de ejecución
3,8 GHz
Intel SpeedStep® Mejorado
*It is recommended to use processors with
Tecnología Extended Memory 64
95W power consumption.
FSB
533 / 800 / 1066 / 1333 MHz
Conjunto de Intel 945GC
chips
Intel ICH7
Gráficos
Intel GMA 950
Memoria máxima de vídeo compartida de 224MB
ITE 8712F
Iniciativas de control de entorno,
Le ofrece las funcionalidades heredadas de
Monitor hardware
uso más común Súper E/S.
Controlador de velocidad de ventilador
Interfaz de cuenta Low Pin
Función "Guardia inteligente" de ITE
Súper E/S
Ranuras DIMM DDR2 x 2
Memoria
principal
Cada DIMM admite DDR2 de 256/512MB y
Módulo de memoria DDR2 de canal Doble
1GB
No admite DIMM registrados o DIMM compatibles
Capacidad máxima de memoria de 2GB
con ECC
Admite DDR2 de 400 / 533 / 667
IDE
Controlador IDE integrado
SATA
Controlador ATA Serie Integrado
Red Local
Atheros L2
Códecs de
sonido
Ranuras
36
Modo bus maestro Ultra DMA 33 / 66 / 100
Soporte los Modos PIO 0~4.
Tasas de transferencia de hasta 3 Gb/s.
Compatible con la versión SATA 2.0.
Negociación de 10 / 100 Mb/s
Funciones Half / Full dúplex
Salida de sonido de 5.1 canales
ALC662
Soporte de sonido Alta Definición
Ranura PCI Express x16
X1
Ranura PCI Express x1
X1
Ranura PCI
X2
945GC-M7 TE
Especificación
Conectores
en placa
Conector disco flexible
X1
Cada conector soporta 2 unidades de disco flexible
Conector IDE
X1
Cada conector soporta 2 dispositivos IDE
Conector Puerto de impresora
X1
Cada conector soporta 1 Puerto de impresora
Conector SATA
X4
Cada conector soporta 1 dispositivos SATA
Conector de panel frontal
X1
Soporta instalaciones en el panel frontal
Conector de sonido frontal
X1
Soporta funciones de sonido en el panel frontal
Conector de entrada de CD
X1
Soporta función de entrada de sonido de CD
Conector de salida S/PDIF
X1
Soporta función de salida de sonido digital
Cabecera de ventilador de CPU
X1
Cabecera de ventilador de sistema X1
Cabecera de borrado de CMOS
X1
Conector USB
X2
Conector de alimentación
X1
Fuente de alimentación de ventilador de CPU (con
función Smart Fan)
Fuente de alimentación de ventilador de sistema
Cada conector soporta 2 puertos USB frontales
(24 patillas)
Conector de alimentación
X1
(4 patillas)
Teclado PS/2
X1
Ratón PS/2
X1
Panel
Puerto serie
X1
trasero de
Puerto VGA
X1
E/S
Puerto de red local
X1
Puerto USB
X4
Conector de sonido
X3
Tamaño de
la placa
190 mm. (A) X 239 mm. (H)
Soporte de
sistema
operativo
Windows 2000 / XP / VISTA
Biostar se reserva el derecho de añadir o retirar el
soporte de cualquier SO con o sin aviso previo.
37
Motherboard Manual
PORTUGUESE
ESPECIFICAÇÕES
LGA 775
Suporta as tecnologias Hyper-Threading
Processador Intel Core2Duo / Pentium 4 /
CPU
Pentium D / Celeron D / Celeron 4xx até 3,8 GHz
*It is recommended to use processors with 95W
power consumption.
FSB
Chipset
Placa
gráfica
Execute Disable Bit
Enhanced Intel SpeedStep®
Extended Memory 64
533 / 800 / 1066 / 1333 MHz
Intel 945GC
Intel ICH7
Intel GMA 950
Memória de vídeo máxima partilhada: 224 MB
ITE 8712F
Iniciativas para controlo do ambiente
Especificaçã Proporciona as funcionalidades mais utilizadas
Monitorização do hardware
o Super I/O em termos da especificação Super I/O.
Controlador da velocidade da ventoinha
Interface LPC (Low Pin Count).
Função "Smart Guardian" da ITE
Ranhuras DIMM DDR2 x2
Memória
principal
Cada módulo DIMM suporta uma memória
Módulo de memória DDR2 de canal duplo
DDR2 de 256/512 MB & 1 GB
Os módulos DIMM registados e os DIMM ECC
Capacidade máxima de memória: 2 GB
não são suportados
Suporta módulos DDR2 400 / 533 / 667
IDE
Modo Bus master Ultra DMA 33 / 66 / 100
Controlador IDE integrado
Suporta o modo PIO 0~4.
Velocidades de transmissão de dados até 3 Gb/s.
SATA
Controlador Serial ATA integrado
Compatibilidade com a especificação SATA
versão 2.0.
LAN
Codec de
som
Ranhuras
38
Auto negociação de 10 / 100 Mb/s
Atheros L2
Capacidade semi/full-duplex
Saída de áudio de 5.1 canais
ALC662
Suporta a especificação High-Definition Audio
Ranhura PCI Express x16
x1
Ranhura PCI Express x1
x1
Ranhura PCI
x2
945GC-M7 TE
ESPECIFICAÇÕES
Conector da unidade de disquetes
x1
Cada conector suporta 2 unidades de disquetes
Conector IDE
x1
Cada conector suporta 2 dispositivos IDE
Conector da para impressora
x1
Cada conector suporta 1 Porta para impressora
Conector SATA
x4
Cada conector suporta 1 dispositivo SATA
Conector do painel frontal
x1
Para suporte de várias funções no painel frontal
Conector de áudio frontal
x1
Suporta a função de áudio no painel frontal
Conector para entrada de CDs
x1
Suporta a entrada de áudio a partir de CDs
x1
Suporta a saída de áudio digital
Conectores Conector de saída S/PDIF
na placa
Entradas/S
aídas no
painel
traseiro
Tamanho
da placa
Conector da ventoinha da CPU
x1
Conector da ventoinha do sistema
x1
Conector para limpeza do CMOS
x1
Conector USB
x2
Conector de alimentação (24 pinos)
x1
Conector de alimentação (4 pinos)
x1
Teclado PS/2
x1
Rato PS/2
x1
Porta série
x1
Porta VGA
x1
Porta LAN
x1
Porta USB
x4
Tomada de audio
x3
suportados
Smart Fan)
Alimentação da ventoinha do sistema
Cada conector suporta 2 portas USB no painel
frontal
190 mm (L) X 239 mm (A)
Sistemas
operativos
Alimentação da ventoinha da CPU (com a função
A Biostar reserva-se o direito de adicionar ou
Windows 2000 / XP / VISTA
remover suporte para qualquer sistema
operativo com ou sem aviso prévio.
39
Motherboard Manual
POLISH
SPEC
LGA 775
Procesor Intel Core2Duo / Pentium 4 / Pentium D
Procesor
/ Celeron D / Celeron 4xx do 3,8 GHz
*It is recommended to use processors with 95W
power consumption.
FSB
Chipset
Grafika
Obsługa Hyper-Threading
Execute Disable Bit
Enhanced Intel SpeedStep®
Extended Memory 64 Technology
533 / 800 / 1066 / 1333 MHz
Intel 945GC
Intel ICH7
Maks. wielkość współdzielonej pamięci video
Intel GMA 950
wynosi 224MB
Gniazda DDR2 DIMM x 2
Pamięć
główna
Każde gniazdo DIMM obsługuje moduły
Moduł pamięci DDR2 z trybem podwójnego
256/512MB oraz 1GB DDR2
kanału
Maks. wielkość pamięci 2GB
Brak obsługi Registered DIMM oraz ECC DIMM
Obsługa DDR2 400 / 533 / 667
ITE 8712F
Super I/O
Funkcje kontroli warunków pracy,
Zapewnia najbardziej powszechne funkcje Super Monitor H/W
I/O.
Kontroler prędkości wentylatora
Interfejs Low Pin Count
Funkcja ITE "Smart Guardian"
IDE
Zintegrowany kontroler IDE
SATA
Zintegrowany kontroler Serial ATA
Ultra DMA 33 / 66 / 100 Tryb Bus Master
obsługa PIO tryb 0~4
Transfer danych do 3 Gb/s.
Zgodność ze specyfikacją SATA w wersji 2.0.
10 / 100 Mb/s z automatyczną negocjacją
LAN
szybkości
Atheros L2
Działanie w trybie połowicznego / pełnego
dupleksu
Kodek
dźwiękowy
ALC662
Gniazdo PCI Express x16
Gniazda
40
5.1 kanałowe wyjście audio
Obsługa High-Definition Audio
x1
Gniazdo PCI Express x1
x1
Gniazdo PCI
x2
945GC-M7 TE
SPEC
Złącza
Złącze napędu dyskietek
x1
Każde złącze obsługuje 2 napędy dyskietek
Złącze IDE
x1
Każde złącze obsługuje 2 urządzenia IDE
Złącze Port drukarki
x1
Każde złącze obsługuje 1 Port drukarki
Złącze SATA
x4
Każde złącze obsługuje 1 urządzenie SATA
Złącze panela przedniego
x1
Obsługa elementów panela przedniego
Przednie złącze audio
x1
Obsługa funkcji audio na panelu przednim
Złącze wejścia CD
x1
Obsługa funkcji wejścia audio CD
Złącze wyjścia S/PDIF
x1
Obsługa funkcji cyfrowego wyjścia audio
wbudowane Złącze główkowe wentylatora procesora
x1
Złącze główkowe wentylatora
Back Panel
I/O
Wymiary
płyty
systemowego
x1
Złącze główkowe kasowania CMOS
x1
Złącze USB
x2
Złącze zasilania (24 pinowe)
x1
Złącze zasilania (4 pinowe)
x1
Klawiatura PS/2
x1
Mysz PS/2
x1
Port szeregowy
x1
Port VGA
x1
Port LAN
x1
Port USB
x4
Gniazdo audio
x3
operacyjne
go
Zasilanie wentylatora systemowego
Każde złącze obsługuje 2 porty USB na panelu
przednim
190 mm (S) X 239 mm (W)
Obsluga
systemu
Zasilanie wentylatora procesora (z funkcją Smart
Fan)
Biostar zastrzega sobie prawo dodawania lub
Windows 2000 / XP / VISTA
odwoływania obsługi dowolnego systemu
operacyjnego bez powiadomienia.
41
Motherboard Manual
RUSSIAN
СПЕЦ
CPU
(центральн
ый
процессор)
LGA 775
Поддержка технологий Hyper-Threading
Процессор Intel Core2Duo / Pentium 4 /
Pentium D / Celeron D / Celeron 4xx до 3.8 ГГц
*It is recommended to use processors with 95W
power consumption.
FSB
533 / 800 / 1066 / 1333 МГц
Набор
Intel 945GC
Execute Disable Bit
Enhanced Intel SpeedStep®
Extended Memory 64 Technology
микросхем Intel ICH7
Графика
Максимальная совместно используемая видео
Intel GMA 950
память составляет 224 МБ
Слоты DDR2 DIMM x 2
Основная
память
Модуль памяти с двухканальным режимом
Каждый модуль DIMM поддерживает
DDR2
256/512МБ & 1ГБ DDR2
Не поддерживает зарегистрированные
Максимальная ёмкость памяти 2 ГБ
модули DIMM and ECC DIMM
Поддержка DDR2 400 / 533 / 667
Super I/O
IDE
SATA
Локальная
сеть
Звуковой
кодек
Слоты
Встроенны
й разъём
ITE 8712F
Инициативы по охране окружающей среды,
Обеспечивает наиболее используемые
Аппаратный монитор
действующие функциональные возможности Регулятор скорости
Super I/O.
Функция ITE "Smart Guardian"
Интерфейс с низким количеством выводов
(Интеллектуальная защита)
Встроенное устройство управления
Режим "хозяина" шины Ultra DMA 33 / 66 / 100
встроенными интерфейсами устройств
Поддержка режима PIO 0~4,
Встроенное последовательное устройство
скорость передачи данных до 3 гигабит/с.
управления ATA
Соответствие спецификации SATA версия 2.0.
Частичная / полная дуплексная способность
5.1канальный звуковой выход
ALC662
Звуковая поддержка High-Definition
Слот PCI Express x16
x1
Слот PCI Express x1
x1
Слот PCI
x2
Разъём НГМД
x1
Разъём IDE
42
Автоматическое согласование 10 / 100 Мб/с
Atheros L2
x1
Каждый разъём поддерживает 2 накопителя
на гибких магнитных дисках
Каждый разъём поддерживает 2 встроенных
интерфейса накопителей
945GC-M7 TE
СПЕЦ
Разъём Порт подключения принтера
x1
Разъём SATA
x4
Разъём на лицевой панели
x1
Входной звуковой разъём
x1
Разъём ввода для CD
x1
Разъём вывода для S/PDIF
x1
подключения принтера
Каждый разъём поддерживает 1 устройство
SATA
Поддержка устройств на лицевой панели
Поддержка звуковых функций на лицевой
панели
Поддержка функции ввода для CD
Поддержка вывода цифровой звуковой
функции
Источник питания для вентилятора
Контактирующее приспособление
вентилятора центрального процессора x1
Контактирующее приспособление
вентилятора системы
Каждый разъём поддерживает 1 Порт
x1
центрального процессора (с функцией
интеллектуального вентилятора)
Источник питания для вентилятора системы
Открытое контактирующее
приспособление CMOS
x1
USB-разъём
x2
Разъем питания (24 вывод)
x1
Разъем питания (4 вывод)
x1
Клавиатура PS/2
x1
Задняя
Мышь PS/2
x1
панель
Последовательный порт
x1
средств
Порт VGA
x1
ввода-выв Порт LAN
x1
ода
USB-порт
x4
Гнездо для подключения наушников
x3
Размер
панели
Поддержка
OS
Каждый разъём поддерживает 2 USB-порта на
лицевой панели
190 мм (Ш) X 239 мм (В)
Biostar сохраняет за собой право добавлять
Windows 2000 / XP / VISTA
или удалять средства обеспечения для OS с
или без предварительного уведомления.
43
‫‪Motherboard Manual‬‬
‫‪ARABIC‬‬
‫اﻟﻤﻮاﺻﻔﺎت‬
‫‪LGA 775‬‬
‫‪Intel Core2Duo / Pentium 4 / Pentium D /‬ﻡﻌﺎﻟﺠﺎت‬
‫وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ‬
‫اﻟﻤﺮآﺰﻳﺔ‬
‫ﺑﺘﺮدد ﻳﺼﻞ إﻟﻰ ‪ 3.8‬ﺝﻴﺠﺎ هﺮﺕﺰ‪Celeron D / Celeron 4xx‬‬
‫‪*It is recommended to use processors with 95W‬‬
‫‪power consumption.‬‬
‫‪Hyper-Threading‬ﺕﺪﻋﻢ ﺕﻘﻨﻴﺎت‬
‫‪Execute Disable Bit‬‬
‫®‪Enhanced Intel SpeedStep‬‬
‫‪Extended Memory 64 Technology‬‬
‫اﻟﻨﺎﻗﻞ اﻷﻡﺎﻡﻲ اﻟﺠﺎﻥﺒﻲ ﻡﻴﺠﺎ هﺮﺕﺰ ‪533 / 800 / 1066 / 1333‬ﺕﺮدد‬
‫‪Intel 945GC‬‬
‫ﻡﺠﻤﻮﻋﺔ اﻟﺸﺮاﺋﺢ‬
‫ﺑﻄﺎﻗﺔ اﻟﺮﺳﻮﻡﺎت‬
‫‪Intel ICH7‬‬
‫‪Intel GMA 950‬‬
‫ﻡﻴﺠﺎ ﺑﺎﻳﺖ‪224‬أﻗﺼﻰ ﺳﻌﺔ ﻟﺬاآﺮة اﻟﻔﻴﺪﻳﻮ اﻟﻤﺸﺘﺮآﺔ‬
‫‪2‬ﻋﺪد‪DDR2 DIMM‬ﻓﺘﺤﺔ‬
‫ﻡﻴﺠﺎ ‪ 256/512‬ﺳﻌﺔ ‪ DDR2‬ﺕﺪﻋﻢ ذاآﺮة ﻡﻦ ﻥﻮع ‪DIMM‬ﺕﺪﻋﻢ آﻞ ﻓﺘﺤﺔ‬
‫اﻟﺬاآﺮة اﻟﺮﺋﻴﺴﻴﺔ‬
‫أﺣﺎدﻳﺔ‪/‬ﻡﺰدوﺝﺔ اﻟﻘﻨﺎة‪DDR2‬وﺣﺪة ذاآﺮة‬
‫ﺑﺎﻳﺖ و‪ 1‬ﺝﻴﺠﺎ ﺑﺎﻳﺖ‬
‫‪ ECC‬وﺕﻠﻚ اﻟﺘﻲ ﻻ ﺕﺘﻮاﻓﻖ ﻡﻊ ‪DIMM‬ﻻ ﺕﺪﻋﻢ رﻗﺎﺋﻖ اﻟﺬاآﺮة‬
‫ﺳﻌﺔ ذاآﺮة ﻗﺼﻮى ‪ 2‬ﺝﻴﺠﺎ ﺑﺎﻳﺖ‬
‫ﻡﻴﺠﺎ ﺑﺎﻳﺖ‪ 400 / 533 / 667‬ﺳﻌﺎت ‪DDR2‬ﺕﺪﻋﻢ اﻟﺬاآﺮة ﻡﻦ ﻥﻮع‬
‫وﺳﺎﺋﻞ اﻟﺘﺤﻜﻢ ﻓﻲ اﻟﺒﻴﺌﺔ‪:‬‬
‫‪ITE 8712F‬‬
‫‪Super I/O‬‬
‫ﻡﺮاﻗﺐ ﻟﻤﻌﺮﻓﺔ ﺣﺎﻟﺔ اﻷﺝﻬﺰة‬
‫اﻷآﺜﺮ اﺳﺘﺨﺪاﻡًﺎ‪Super I/O .‬ﺕﻮﻓﺮ وﻇﻴﻔﺔ‬
‫ﻡﺮاﻗﺐ ﻓﻲ ﺳﺮﻋﺔ اﻟﻤﺮوﺣﺔ‬
‫‪Low Pin Count Interface‬ﺕﺪﻋﻢ ﺕﻘﻨﻴﺔ‬
‫‪ ITE‬ﻡﻦ "‪"Smart Guardian‬وﻇﻴﻔﺔ‬
‫‪Ultra DMA 33 / 66 / 100‬ﻥﺎﻗﻞ ﺑﺘﻘﻨﻴﺔ‬
‫ﻡﻨﻔﺬ ‪IDE‬‬
‫ﻡﺘﻜﺎﻡﻞ‪IDE‬ﻡﺘﺤﻜﻢ‬
‫‪SATA‬‬
‫ﻡﺘﻜﺎﻡﻞ‪Serial ATA‬ﻡﺘﺤﻜﻢ‬
‫وﺿﻊ رﺋﻴﺴﻲ‬
‫‪PIO Mode 0~4‬دﻋﻢ وﺿﻊ‬
‫ﺵﺒﻜﺔ داﺥﻠﻴﺔ‬
‫‪100/10‬‬
‫آﻮدﻳﻚ اﻟﺼﻮت‬
‫ﻥﻘﻞ اﻟﺒﻴﺎﻥﺎت ﺑﺴﺮﻋﺎت ﺕﺼﻞ إﻟﻰ ‪ 3‬ﺝﻴﺠﺎﺑﺖ‪/‬ﺙﺎﻥﻴﺔ‪.‬‬
‫‪ 2.0.‬اﻹﺹﺪار‪SATA‬ﻡﻄﺎﺑﻘﺔ ﻟﻤﻮاﺹﻔﺎت‬
‫ﺕﻔﺎوض ﺕﻠﻘﺎﺋﻲ ‪ 100/10‬ﻡﻴﺠﺎ ﺑﺎﻳﺖ ‪ /‬ﺙﺎﻥﻴﺔ‬
‫‪Atheros L2‬‬
‫إﻡﻜﺎﻥﻴﺔ اﻟﻨﻘﻞ اﻟﻤﺰدوج اﻟﻜﺎﻡﻞ‪/‬اﻟﻨﺼﻔﻲ‬
‫ﻗﻨﻮات ﻟﺨﺮج اﻟﺼﻮت‪5.1‬‬
‫‪ALC662‬‬
‫ﺕﺪﻋﻢ ﺕﻘﻨﻴﺔ اﻟﺼﻮت ﻋﺎﻟﻲ اﻟﺘﻌﺮﻳﻒ ﻡﻦ‬
‫اﻟﻔﺘﺤﺎت‬
‫ﻓﺘﺤﺔ ‪PCI Express x16‬‬
‫ﻋﺪد ‪1‬‬
‫ﻓﺘﺤﺔ ‪PCI Express x1‬‬
‫ﻋﺪد ‪1‬‬
‫ﻓﺘﺤﺔ ‪PCI‬‬
‫ﻋﺪد ‪2‬‬
‫‪44‬‬
‫‪945GC-M7 TE‬‬
‫اﻟﻤﻮاﺻﻔﺎت‬
‫ﻡﻨﻔﺬ ﻡﺤﺮك أﻗﺮاص ﻡﺮﻥﺔ‬
‫ﻋﺪد ‪1‬‬
‫ﻳﺪﻋﻢ ﻡﺤﺮآﻴﻦ ﻟﻸﻗﺮاص اﻟﻤﺮﻥﺔ‬
‫ﻡﻨﻔﺬ ‪IDE‬‬
‫ﻋﺪد ‪1‬‬
‫‪IDE‬ﻳﺪﻋﻢ آﻞ ﻡﻨﻔﺬ اﺙﻨﻴﻦ ﻡﻦ أﺝﻬﺰة‬
‫ﻡﻨﻔﺬ ﻃﺎﺑﻌﺔ‬
‫ﻋﺪد ‪1‬‬
‫ﻡﻨﻔﺬ ‪SATA‬‬
‫ﻋﺪد ‪4‬‬
‫‪SATA‬ﻳﺪﻋﻢ آﻞ ﻡﻨﻔﺬ واﺣﺪ ﻡﻦ أﺝﻬﺰة‬
‫ﻡﻨﻔﺬ اﻟﻠﻮﺣﺔ اﻷﻡﺎﻡﻴﺔ‬
‫ﻋﺪد ‪1‬‬
‫ﻳﺪﻋﻢ ﺕﺠﻬﻴﺰات اﻟﻠﻮﺣﺔ اﻷﻡﺎﻡﻴﺔ‬
‫ﻡﻨﻔﺬ اﻟﺼﻮت اﻷﻡﺎﻡﻲ‬
‫ﻋﺪد ‪1‬‬
‫ﻳﺪﻋﻢ وﻇﻴﻔﺔ اﻟﺼﻮت ﺑﺎﻟﻠﻮﺣﺔ اﻷﻡﺎﻡﻴﺔ‬
‫اﻟﻤﻨﺎﻓﺬ ﻋﻠﻰ ﺳﻄﺢ‬
‫ﻡﻨﻔﺬ ‪CD-IN‬‬
‫ﻋﺪد ‪1‬‬
‫ﻳﺪﻋﻢ وﻇﻴﻔﺔ دﺥﻞ ﺹﻮت اﻟﻘﺮص اﻟﻤﺪﻡﺞ‬
‫اﻟﻠﻮﺣﺔ‬
‫ﻡﻨﻔﺬ ﺥﺮج ‪S/PDIF‬‬
‫ﻋﺪد ‪1‬‬
‫ﻳﺪﻋﻢ وﻇﻴﻔﺔ ﺥﺮج اﻟﺼﻮت اﻟﺮﻗﻤﻲ‬
‫وﺹﻠﺔ ﻡﺮوﺣﺔ وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ اﻟﻤﺮآﺰﻳﺔ‬
‫ﻋﺪد ‪1‬‬
‫(‪Smart Fan‬ﻟﺘﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ ﻟﻤﺮوﺣﺔ وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ )ﻡﻊ وﻇﻴﻔﺔ‬
‫وﺹﻠﺔ ﻡﺮوﺣﺔ اﻟﻨﻈﺎم‬
‫ﻋﺪد ‪1‬‬
‫ﻟﺘﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ ﻟﻤﺮوﺣﺔ اﻟﻨﻈﺎم‬
‫وﺹﻠﺔ ﻡﺴﺢ ‪CMOS‬‬
‫ﻋﺪد ‪1‬‬
‫ﻡﻨﻔﺬ ‪USB‬‬
‫ﻋﺪد ‪2‬‬
‫ﻡﻨﻔﺬ ﺕﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ )‪24‬دﺑﻮس(‬
‫ﻋﺪد ‪1‬‬
‫ﻡﻨﻔﺬ ﺕﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ )‪4‬دﺑﺎﺑﻴﺲ(‬
‫ﻋﺪد ‪1‬‬
‫ﻟﻮﺣﺔ ﻡﻔﺎﺕﻴﺢ ‪PS/2‬‬
‫ﻋﺪد ‪1‬‬
‫ﻡﺎوس ‪PS/2‬‬
‫ﻋﺪد ‪1‬‬
‫ﻡﻨﻔﺬ ﺕﺴﻠﺴﻠﻲ‬
‫ﻋﺪد ‪1‬‬
‫ﻡﻨﻔﺬ ‪VGA‬‬
‫ﻋﺪد ‪1‬‬
‫ﻡﻨﻔﺬ ﺵﺒﻜﺔ اﺕﺼﺎل ﻡﺤﻠﻴﺔ‬
‫ﻋﺪد ‪1‬‬
‫ﻡﻨﺎﻓﺬ ‪USB‬‬
‫ﻋﺪد ‪4‬‬
‫ﻡﻘﺒﺲ ﺹﻮت‬
‫ﻋﺪد ‪3‬‬
‫ﻡﻨﺎﻓﺬ دﺥﻞ‪/‬ﺥﺮج‬
‫اﻟﻠﻮﺣﺔ اﻟﺨﻠﻔﻴﺔ‬
‫ﺣﺠﻢ اﻟﻠﻮﺣﺔ‬
‫دﻋﻢ أﻥﻈﻤﺔ اﻟﺘﺸﻐﻴﻞ‬
‫‪45‬‬
‫ﺑﺎﻟﻠﻮﺣﺔ اﻷﻡﺎﻡﻴﺔ‪USB‬ﻳﺪﻋﻢ آﻞ ﻡﻨﻔﺬ ﻓﺘﺤﺘﻲ‬
‫‪ 190‬ﻡﻢ )ﻋﺮض( ‪ 239 X‬ﻡﻢ )ارﺕﻔﺎع(‬
‫‪Windows 2000 / XP / VISTA‬‬
‫ﺑﺤﻘﻬﺎ ﻓﻲ إﺿﺎﻓﺔ أو إزاﻟﺔ اﻟﺪﻋﻢ ﻷي ﻥﻈﺎم ﺕﺸﻐﻴﻞ ﺑﺈﺥﻄﺎر أو ‪Biostar‬ﺕﺤﺘﻔﻆ‬
‫ﺑﺪون إﺥﻄﺎر‪.‬‬
Motherboard Manual
JAPANESE
仕様
LGA 775
Intel Core2Duo / Pentium 4 / Pentium D /
CPU
Celeron D / Celeron 4xx processor up to 3.8 GHz
*It is recommended to use processors with 95W
power consumption.
FSB
Hyper-Threading
Execute Disable Bit
Enhanced Intel SpeedStep®
Extended Memory 64 Technology
533 / 800 / 1066 / 1333 MHz
Intel 945GC
チップセット
グラフィック
Intel ICH7
Intel GMA 950
最大の共有ビデオメモリは224MBです
ス
DDR2 DIMMスロット x 2
各DIMMは256/512MB & 1GB DDR2をサポート
デュアル チャンネルモードDDR2メモリモジュール
最大メモリ容量2GB
登録済みDIMMとECC DIMMはサポートされません
メインメモリ
DDR2 400 / 533 / 667 をサポート
ITE 8712F
Super I/O
環境コントロールイニシアチブ、
もっとも一般に使用されるレガシーSuper I/O機能を H/Wモニター
採用しています。
ファン速度コントローラ/ モニター
低ピンカウントインターフェイス
ITEの「スマートガーディアン」機能
Ultra DMA 33 / 66 / 100バスマスタモード
IDE
統合IDEコントローラ
SATA
統合シリアルATAコントローラ
PIO Mode 0~4のサポート
最高3 Gb/秒のデータ転送速度
SATAバージョン2.0仕様に準拠。
10 / 100 Mb/秒のオートネゴシエーション
10/100 LAN Atheros L2
半/全二重機能
サウンド
Codec
スロット
46
5.1チャンネルオーディオアウト
ALC662
ハイデフィニションオーディオのサポート
PCI Express x16スロット
x1
PCI Express x1スロット
x1
PCIスロット
x2
945GC-M7 TE
仕様
フロッピーコネクタ
x1
各コネクタは2つのフロッピードライブをサポートし
ます
IDEコネクタ
x1
各コネクタは2つのIDEデバイスをサポートします
プリンタポートコネクタ
x1
各コネクタは1つのプリンタポートをサポートします
SATAコネクタ
x4
各コネクタは1つのSATAデバイスをサポートします
フロントパネルコネクタ
x1
フロントパネル機能をサポートします
フロントオーディオコネクタ
x1
フロントパネルオーディオ機能をサポートします
x1
CDオーディオイン機能をサポートします
S/PDIFアウトコネクタ
x1
デジタルオーディオアウト機能をサポートします
CPUファンヘッダ
x1
CPUファン電源装置(スマートファン機能を搭載)
システムファンヘッダ
x1
システムファン電源装置
CMOSクリアヘッダ
x1
USBコネクタ
x2
オンボードコ CDインコネクタ
ネクタ
各コネクタは2つのフロントパネルUSBポートをサポ
ートします
背面パネル
I/O
電源コネクタ(24ピン)
x1
電源コネクタ(4ピン)
x1
PS/2キーボード
x1
PS/2マウス
x1
シリアルポート
x1
VGAポート
x1
LANポート
x1
USBポート
x4
オーディオジャック
x3
ボードサイズ 190 mm (幅) X 239 mm (高さ)
OSサポート Windows 2000 / XP / VISTA
Biostarは事前のサポートなしにOSサポートを追加ま
たは削除する権利を留保します。
2007/08/31
47
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement