Product Sheet for CXD 2.0kW Ceramic Heater

Product Sheet for CXD 2.0kW Ceramic Heater
CXD2000H
CXD2000V
08/19367/2
Issue 2
The product complies with the European Safety Standards EN60335-2-30 and the European Standard Electromagnetic Compatibility (EMC) EN55014,
EN60555-2 and EN60555-3. These cover the essential requirements of EEC Directives 2006/95/EC and 2004/108/EC
1
500 MIN.
500 MIN.
121
442
442
121
380
380
Front View
302
Plan View
Side View
CXD2000V
500 MIN.
500 MIN.
882
882
297
146
306
297
306
Front View
Plan View
Side View
CXD2000H
3
2
1
45
2
Heated Zone
1.8m
Min.
Height
2.0m
Recommended
Mounting
Height
1
4
c
b
e
d
a
Dimplex CXD Ceramic Radiant Heaters
Model(s) : CXD2000H & CXD2000V
(IPX4)
THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
Important Safety Advice
Because the Dimplex Ceramic Radiant Heater contains
no moving parts little maintenance is required. Before
undertaking any maintenance work on the heater due
attention must be paid to the following:
This heater is designed to be horizontally wall mounted
only, it must not be ceiling mounted.
Always ensure a safe mounting height, at or above a
minimum height of 1.8 metres from ground level, so
that the heater can not be touched when in operation.
The heater must be wall mounted level ± 5º to the
horizontal.
Do not locate the heater immediately above or below a
fixed socket outlet or connection box.
This appliance is not intended for use by children or
other persons without assistance or supervision if their
physical, sensory or mental capabilities prevent them
from using it safely. Children should be supervised to
ensure that they do not play with the appliance.
Always disconnect the heater from the electricity supply
before attempting to work on or near it.
Always ensure a safe means of access using an access
tower or properly supported ladder.
Do not cover the heater.
Keep combustible materials away from the heater.
Do not position patio furniture, sunshades, awnings and
other combustible materials too close to the heater.
Do not use heater if the elements are broken - as injury
may occur.
Allow adequate time (minimum of 30 mins.) for the
elements and body casing to cool before attempting to
work on the heater .
Wiring between the heater and the spur outlet or
isolation switch must be in a heat resisting cable (e.g.
polychloroprene).
Note: Provide sufficient slack to the cable to allow for
angular adjustment of the body.
The supply cord should be regularly examined for signs
of damage and the appliance is not to be used if the
cord is damaged.
General
Your Dimplex Ceramic Radiant Heater uses ceramic
elements which produce a high proportion of their output in
the long-wave infra-red. This provides a high comfort factor
– similar to the natural energy from the sun.
Electrical
The installation of this appliance should be carried out by a
competent electrician and be in accordance with the
current IEE wiring regulations and any local or insurance
regulations.
The CXD2000H & CXD2000V are designed for use on a
230-240V AC single phase supply.
An all-pole isolating switch with a minimum separation of
3mm in each pole must be fitted to facilitate isolation. This
switch must either be positioned inside a building or have
an IP rating against water ingress suitable for external
installation.
The appliance must be supplied through a residual current
device (RCD) having a rated residual operating current not
exceeding 30mA.
The appliance must be connected to a socket-outlet having
an earthing contact.
We recommend that a cable with a minimum specification of
H07RN-F polychloroprene sheathed or similar be used with
a minimum temperature rating of 90°C.
Note : Always ensure the cable grip is tightened.
Installation
Heaters are supplied with an integral wall bracket which may
be fixed through the mounting holes to any suitable structure.
The bracket allows the heater to be inclined at the required
angle. The recommended fixing height to the centre line of
the bracket is 2.0m from ground level - see Fig. 2.
The integral wall fixing bracket may be removed by fully
unscrewing to facilitate its fixing.
The siting of the heater(s) should be such as to allow an
even and uninterrupted distribution of radiation to the area(s)
to be heated. Heaters are most effective when the beam
angle is inclined down at an angle of between 30º to 45º to
the vertical - see Fig. 2.
When deciding upon the best location, consideration must
be given to the following requirements:
a. Avoid structures which might vibrate e.g. crane gantries.
These could adversely affect element life.
b. Comfort and safety could be compromised unless the
heater is mounted at or above 1.8m from ground level.
c. Allow a minimum of 500mm minimum clearance
between the top of the heater and any horizontal surface
- see Fig. 1.
Element Replacement (see Fig. 4)
WARNING – BEFORE UNDERTAKING THIS TASK ENSURE THE
HEATER IS DISCONNECTED FROM THE ELECRICITY SUPPLY
AND LEFT TO COOL FOR A MINIMUM OF 30 MINUTES.
1. The heater should be taken off the wall.
2. Remove the screws (a) and (b) which hold the control
box on the back of the heater.
3. This will allow access to the elements. Remove the
retaining clips and spring clips (c) to loosen the
elements.
4. Disconnect the elements from their terminal blocks.
5. Remove the screws (d) which hold the back panel.
6. Remove the splash brackets (e) on the elements.
7. Bend the bars on the guard as indicated in Fig. 3 to
remove it.
8. The old element should drop out through the front of the
heater, reverse the process when replacing with the new
element.
Cleaning and User Maintenance
WARNING: BEFORE UNDERTAKING CLEANING OR
MAINTENANCE WORK ON THE APPLIANCE, DISCONNECT
THE ELECTRICITY SUPPLY.
Since the appliance contains no moving parts little
maintenance is required beyond cleaning and element
replacement. It is however essential that the heater is not
operated with an accumulation of dust or dirt on the element,
as this can cause a build up of heat and eventual damage.
For this reason the heater must be inspected regularly,
depending upon conditions and at least at yearly intervals.
Allow adequate time for the element and body casing to cool
before attempting to work on the heater - a minimum time of
30 minutes is recommended.
Recycling
For electrical products sold within the European Community.
At the end of the electrical products useful life it
should not be disposed of with household waste.
Please recycle where facilities exist. Check with
your Local Authority or retailer for recycling advice
in your country.
After Sales Service
Your product is guaranteed for one year from the date of
purchase.
Within this period, we undertake to repair or exchange this
product free of charge (excluding element & subject to
availability) provided it has been installed and operated in
accordance with these instructions.
Your rights under this guarantee are additional to your statutory
rights, which in turn are not affected by this guarantee.
Should you require after sales information or assistance
with this product please go to www.dimplex.co.uk where
you will find our self help guide by clicking on “After Sales”
or ring our helpdesk on 0845 600 5111 (UK) or 01 842 4833
(R.O.I.) .
Spare parts are also available on the website
www.dimplex.co.uk
Please retain your receipt as proof of purchase.
Dimplex UK Ltd.
Millbrook House
Grange Drive
Hedge End
Southampton
Hampshire. SO30 2DF
www.dimplex.co.uk
Republic of Ireland Tel.
01 8424833
[c] Dimplex UK Limited
All rights reserved. Material contained in this publication may not be reproduced in whole or in part, without prior permission in writing of Dimplex UK Limited.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising