Ubiqconn T10C User`s guide

Ubiqconn T10C User`s guide
Rugged Tablet PC
T10C
User’s Guide
T10C User Guide
Introduction
1.
Please read these safety instructions carefully.
2.
Please keep this User’s Manual for later reference.
3.
Please disconnect this equipment from connecter before
cleaning. Don’t use liquid or prayed detergent for cleaning.
User moisture sheet or cloth for cleaning.
4.
Make sure the equipments are connected to the power source
with the correct voltage, frequency, and ampere.
5.
All cautions and warnings on the equipment should be noted.
6.
Never pour any liquid into opening: this could cause fire or
electrical shock.
7.
Never open the equipment. For safety reason, the equipment
should only be opened by qualified service personnel.
8.
If one of the following situations arises, get the equipment
checked by a service personnel:
a. Liquid has penetrated into the equipment.
b. The equipment has been exposed to moisture.
c. The equipment has not worked well or you cannot get it
work according to user manual.
d. The equipment has dropped and damaged. If the
equipment has obvious sign of breakage.
2
T10C User Guide
9.
Caution on use of battery: User the battery recommended by
the manufacturer or the same type of battery installed by the
manufacturer. If incorrect battery is used, it may cause
explosion or fire hazard. Recycle or discard used batteries
according the manufacturer’s instruction or your local
authority.
10. The computers use nonvolatile memory that requires a battery
to retain system information when power is removed. The 3V
lithium battery is on the system board. The battery life
depends on the amount of time the computer is powered on. If
the computer does not display the correct time and date,
replace the battery.
IMPORTANT:Loss of BIOS settings occurs when the battery is
removed. BIOS settings must be reconfigured whenever the
battery is replaced.
WARNING:A risk of fire and chemical burn exists if the battery
is not handled properly. Do not disassemble, crush, puncture, or
short external contacts, or expose the battery to temperatures
higher than 60 °C (140 °F). Do not dispose of a used battery in
water or fire.
CAUTION:Danger of explosion if battery is incorrectly replaced.
3
T10C User Guide
Replace only with same or equivalent type recommended by the
manufacturer. Discard used batteries according to the
manufacturer’s instructions.
FCC Compliance Statement
This equipment has been tested and found to comply with the
limits for a class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for
help.
4
T10C User Guide
FCC Caution: Any changes or modifications not expressly
approved by the party responsible for compliance could void the
user's authority to operate this equipment.
FCC RF Radiation Exposure Statement:
1. This Transmitter has been demonstrated co-location
compliance requirements with Wi-Fi, Bluetooth and RFID
Modules. This transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter.
2. This equipment complies with FCC RF radiation exposure limits
set forth for an uncontrolled environment. This device was
tested for typical hand held operations with the device
contacted directly to the human body to the back side of the
tablet pc. To maintain compliance with FCC RF exposure
compliance requirements, avoid direct contact to the
transmitting antenna during transmitting.
Europe – EU Declaration of Conformity
This device complies with the essential requirements of the
R&TTE Directive 1999/5/EC and EMC directive 2004/108/EC. The
following test methods have been applied in order to prove
presumption of conformity with the essential requirements of the
R&TTE Directive 1999/5/EC and EMC directive 2004/108/EC:
5
T10C User Guide




EN 55022: 2006 +A1: 2007
EN 61000-3-2 : 2006
EN 61000-3-3 : 1995 + A1 : 2001 + A2 : 2005
EN 55024: 1998 + A1: 2001 + A2: 2003
(IEC 61000-4-2: 2008;
IEC 61000-4-3: 2006 + A1:2007;
IEC 61000-4-4: 2004;
IEC 61000-4-5: 2005;
IEC 61000-4-6: 2003 + A1: 2004 +A2: 2006;
IEC 61000-4-8: 1993 +A1: 2000;
IEC 61000-4-11: 2004)
 EN 60950-1: 2001
Safety of information technology equipment
 EN 300 328 V1.7.1: 2006
 EN 301 489-17 V2.1.1: 2009 and EN 301 489-1 V1.8.1: 2008
 EN 62311: 2008
This device is a 2.4GHz wideband transmission system
(transceiver), intended for use in all EU member states and EFTA
countries under the following conditions and/or with the following
restrictions:
 In Italy the end-user should apply for a license at the national
spectrum authorities in order to obtain authorization to use
the device for setting up outdoor radio links and/or for
supplying public access to telecommunications and/or
6
T10C User Guide
network services.
 This device may not be used for setting up outdoor radio links in
France and in some areas the RF output power may be limited to 10
mW EIRP in the frequency range of 2454 – 2483.5 MHz. For detailed
information the end-user should contact the national spectrum
authority in France.
VCCI statement
7
T10C User Guide
Table of Contents
Introduction ............................................................ 2
Table of Contents ................................................... 8
Chapter 1 .............................................................. 12
General Information ............................................. 12
1.1. Introduction ........................................................................................12
1.2. Specification .......................................................................................13
1.2.1. Main System ............................................................................................ 13
1.2.2. I/O Interface ............................................................................................. 14
1.2.3. In Front Control ........................................................................................ 14
1.2.4. Power Management ................................................................................. 15
1.2.5. Environment ............................................................................................. 15
1.2.6. Material .................................................................................................... 16
1.2.7. Operation OS ........................................................................................... 16
1.2.8. Certifications ............................................................................................ 16
1.2.9. Optional: Internal Module ......................................................................... 17
8
T10C User Guide
1.2.10. Optional: External Accessories .............................................................. 17
1.3. Packing List ........................................................................................19
Chapter 2 .............................................................. 20
System Setup ....................................................... 20
2.1. Exploring Your T10C ..........................................................................20
2.1.1.
The T10C IO ................................................................................... 20
2.2.Preparing for Installation ....................................................................26
2.2.1.Switch ON the main battery ...................................................................... 26
2.2.2.Plugging to the DC supply ........................................................................ 27
2.2.3.Starting Your System ................................................................................ 28
2.2.4.Connecting the keyboard and mouse ....................................................... 29
Chapter 3 .............................................................. 30
Using the T10C ..................................................... 30
3.1.Introduction .........................................................................................30
3.2.Using the USB Ports ...........................................................................30
3.3.Using the External Audio System .....................................................31
3.4.Installing the Battery (optional) .........................................................31
3.5.Using a SIM Card.....................................................................................32
9
T10C User Guide
3.5.1.Inserting a SIM Card ................................................................................. 32
3.5.2.Removing a SIM Card............................................................................... 33
3.6. ................................ Using a Barcode Scanner Module or MSR (optional)33
Chapter 4 .............................................................. 36
The BIOS Setup Program .................................... 36
4.1.Main Screen Setup Utility ...................................................................37
4.2.Advanced BIOS Features ...................................................................39
4.3.Security Chip Configuration ..............................................................40
4.4.Boot Management Setup ....................................................................42
4.5.Exit Control ..........................................................................................43
Chapter 5 .............................................................. 44
User Interface for T10C ....................................... 44
5.1.Introduction .........................................................................................44
5.2.About the User Interface ....................................................................44
5.2.1.Enable or disable the User Interface ......................................................... 44
5.2.3.System Status Information ........................................................................ 45
5.3.Using the Application .........................................................................48
5.3.1.Brightness Control .................................................................................... 48
10
T10C User Guide
5.3.2.Volume Control ......................................................................................... 49
5.3.3.Webcam Launch ....................................................................................... 50
5.3.4.Monitor Switch .......................................................................................... 51
5.3.5.RF Device ON/OFF Control ...................................................................... 52
Chapter 6 .............................................................. 55
Maintenance ......................................................... 55
6.1.Maintaining the Battery ......................................................................55
6.2.Maintaining the LCD Display..............................................................56
6.3.Cleaning the T10C ...............................................................................56
11
T10C User Guide
Chapter 1
General Information
1.1. Introduction
T10C rugged tablet PC is Intel® Cedar Trail Platform (N2600+NM10)
processor core architecture based rugged Tablet PC with a bright
10.4-inch LED backlight LCD display. The powerful CPU brings the most
dynamic applications to life without sacrifices to any industrial reliability.
Delivering a variety of connectivity features, built-in USBs, Microphone
and Headphone port. It is ideal for an all-around system performance.
Furthermore, T10C rugged tablet PC is equipped with fanless design.
12
T10C User Guide
1.2. Specification
The T10C rugged tablet PC is a flexible, multi-functional flat tablet PC.
With following specifications that can be applied in diverse operational
environments and implemented in multi-faceted applications.
1.2.1. Main System

Platform:
Intel® Cedar Trail Platform (N2600+NM10)

CPU:
Intel ATOM N2600 1.6GHz Dual core

Graphic:
Intel Graphics Media Accelerator 3600 series

Chipset:
Intel® NM10 Express Chipset

System Memory:
2GB DDRIII 800 SO-DIMM

Storage:
1 x 32G SATA Slim Half-Size Solid State Disk

LCD Panel:
10.4-inch LED Backlight Screen
10.4“ XGA (1024x768) 340nits LCD + T/P(Polarizer + 1/4 λ+ AR)
10.4“ XGA (1024x768) 500nits (after touch)LCD + T/P(Polarizer + 1/4
λ+ AR)

Touch Panel
13
T10C User Guide
5-wire Resistive Touch Screen

Audio:
-1 x High Quality Speaker (2W)
-Internal Microphone : 1 x in front Bezel

Communication :
- 10/100Mbps Ethernet
- Wi-Fi IEEE 802.11 a/b/g/n ; Bluetooth 4.0

Webcam:
Front - 2 Mega-pixel Camera
Rear - 5 Mega-pixel Camera with LED Flash light
1.2.2. I/O Interface


External I/O :

2 x USB 2.0 type A

1 x Audio Jack

1 x Ethernet jack

1 x Docking Connector

1 x DC-Jack
LED Status Indicator:

Power LED Status: 1 x Green/Red Colors

Storage LED Status: 1 x Blue Color

Wi-Fi LED Status: 1 x Blue Color
1.2.3. In Front Control

Switch :

14
1 x Power Button
T10C User Guide


1 x Lock Button

1 x RF Button
Button :

Program Function Buttons : 6 x Function keys (Programmable)
1.2.4. Power Management


Power Adapter :

AC to DC, [email protected], 65W

AC 100V ~ 240V, 50~60Hz input

19 DC-in
Battery (Internal Battery) :

Internal Smart Lithium Polymer Battery, 3800mAh (2S1P), 7.4V
1.2.5. Environment

Operation Temperature :


Storage Temperature :


15
6-ft drop to Plywood (MIL-STD-810G Method 516.6 Procedure
IV)
Vibration :


5-95% without condensation (MIL-STD-810G Method 507.5)
Drop :


-20°C to +70°C (MIL-STD-810G Method 501.5 and 502.5)
Humidity :


-10°C to +50°C (MIL-STD-810G Method 501.5 and 502.5)
Operating : SSD (MIL-STD-810G Method 514.6 Category 4 Fig
514.6C-3)
Mechanical Shock :
T10C User Guide



Operating : 20g, 11ms, Terminal sawtooth
Non-operating : 40g, 11ms, Terminal sawtooth (MIL-STD810G Method 516.6 Procedure I)
Water/Dust Resistance : IP65 equivalent
1.2.6. Material

Chassis :


Enclosure :


PC/ABS Plastic, PC/ABS and TPU Double Injection with
Protective Rubber Grips Set
Dimension (W x H x D mm) :


Semi-Rugged Tablet PC Slate
277.8 x 206 x 26.5mm
Weight :

Approximate 1.2kg (with internal battery)
1.2.7. Operation OS

WIN7 PRO

WES7-WS7P
1.2.8. Certifications


EMI :

FCC part 15 Class B

VCCI (V-3/V-4)

CE (EN55022 / EN55024)
Safety :

16
UL (EN60950), CE
T10C User Guide

RF :


FCC part 15 subpart C
SAR :

FCC SAR (OET 65 C)
1.2.9. Optional: Internal Module

3.5G Sierra MC8355 Gobi3000 :

Protocol :

HSUPA/HSDPA/UMTS/EVDO/EDGE
Frequency :


UMTS/HSUPA/HSDPA 850/900/1800/2100MHz

CDMA/EVDO 800/1900MHz

GSM/GPRS/EDGS 850/900/1800/1900MHz
1.2.10. Optional: External Accessories

MSR :


Reference Standards :

ANSI/ISO Standards 7810,7811-1/6, 7813

JIS II
Decoding Method :


Barcode Scanner :

Decoded Mode :

17
ISO Track1 - IATA , Track2 - ABA and Track3 – THRIFT
1D Symbologies : EAN/UPC, RSS, Code 39, Code 128,
UCC/EAN 128, ISBN, ISBT, Interleaved, Matrix, Industrial
and Standard 2 of 5, Codabar, Code 93/93i, Code 11, MSI,
Plessey, Telepen, postal codes.
T10C User Guide

2D Symbologies: Data Matrix, PDF417, Micro PDF 417,
Maxicode, QR, Aztec, EAN.UCC composite.


GPS :


Channel :
50 channel all-in-view tracking

GPS,GLONASS support

1 x Signal Color LED (Blue)
Desktop Docking :



4 x USB2.0 type A, 1 x Ethernet, 1 x HDMI, 1 x VGA, 1 x
Kensington lock and 1 x DC Jack support
External Battery Kits :

External Battery Pack :


External Battery Charger :


Recharges external battery pack
Vehicle Application Accessories :

18
Hot-swappable Lithium Polymer battery pack - doubles
duration of mobile operation, 4200mAh (2S1P), 7.4V
Vehicle Mounting Docking :

4 x USB2.0 type A, 2 x RS232, 1 x 10/100Mbps
Ethernet, 1 x VGA and DC-Jack support

75 x 75/100 x 100mm Vesa Mount Holes support

6VDC to 36VDC Input (6VDC to 36VDC for Momentary
and 9VDC to 32VDC for Normal)

19 [email protected] Max., total output 30W

Cigarette lighter plug power cord

ACC power cord (option)
T10C User Guide

GPS (option)
1.3. Packing List
19
T10C User Guide
Chapter 2
System Setup
2.1. Exploring Your T10C
Before starting to set up the T10C, get familiar with the locations and
purpose of controls, connectors and I/O ports, which are illustrated in the
figures below. When placed upright, the front panel of the T10C appears as
shown in below.
2.1.1.
The T10C IO
The T10C I/O is as described below.
20
T10C User Guide
F1 Button
F1=explorer
F2 Button
F2=Windows Media Player
F3 Button
F3=OnScreen keyboard
F4 Button
F4=Task Manager
F5 Button
F5=Calculator
Fn Button
Fn = Hotkey Utility
Implement Secure Attention
Sequence (SAS)
Fn+F3 Button (SAS)
Similar function as pressing
Ctrl-Alt-Delete on a standard
keyboard
F1 KEY -LEFT ARROW
Function Key mapping during boot
F2 KEY -UP ARROW
(for Windows system recovery) is as
F3 KEY -ENTER
follows:
F4 KEY -RIGHT ARROW
F5 KEY -DOWN ARROW

21
Camera/2 Mega-pixel
The built-in camera can be used as a communication device for
allowing you to capture images, record videos, and have video
chats. It is 2M pixels and transmitting instant image through
network for conference.
T10C User Guide

Digital Microphone
The built-in microphone receives sounds and voices when used
with the built-in camera.

LED Power/Storage/Wi-Fi
Keeps you informed of your system’s current power status, Storage
access status, and Wi-Fi ON/OFF status.
1. Power Indicator LED
2. Storage Access
3. WiFi ON/OFF

22
Power Indicator LED
To let you know that system is turned on and indicate the
battery charging status.

Lights green when the system is powered on and
battery is discharging or when the system is powered
on and battery is fully charged

Lights blinking red when the system is in S3 Suspend
and battery is charging or when the system is in S3
Suspend and battery is fully charged

Lights red when the system is powered on and battery
is charging.

Lights blinking red indicates that the battery is in
charging and system is power off / S3 Suspend
T10C User Guide


Lights off when power off or the battery is fully
charged.

Storage Access
When LED in blue light indicates that the system is
accessing the Storage Drive.

WiFi ON/OFF
When LED turns on, blue light indicates that the WiFi is
activated. When LED lights off, it indicates that the WiFi
function is disabled.
User Interface Button
This button is used to define the User Interface function. When you
press this button, the system will appear the UI screen as illustrated
below for executing the applications easily and quickly.

Programmable Function Buttons
If your system does not define this button’s function, this button can
be programmable to execute specific application. When you
program your application, please write this directory as listed below
into your configuration file, then the system will aware and execute
this application.
[Setup]
F1_EXE="c:\windows\explorer.exe"
F1_PARA=""
F1_PATH=""
F2_EXE="C:\Program Files\Windows Media Player\wmplayer.exe"
F2_PARA="/prefetch: 1"
F2_PATH=""
F3_EXE="C:\WINDOWS\system32\osk.exe"
F3_PARA=""
23
T10C User Guide
F3_PATH=""
F4_EXE="C:\WINDOWS\system32\taskmgr.exe"
F4_PARA=""
F4_PATH=""
The configuration file is "c:\FKeySet.txt"

Camera/5Mega-pixel
The built-in camera can be used as a communication device for
allowing you to capture images, record videos, and have video
chats. It is 5.0 M pixels and transmitting instant image through
network for conference.
Power Button

Switch the computer power on and off, or resumes whenever it is in
Suspend mode (by OS define).

USB Ports
The two USB (type-A) ports allows you to connect USB
2.0-compliant devices (for example, mouse, keyboard and so on) to
your Tablet PC.

3.5mm Headphone Jack
Allows you to connect an external 3.5mm 4-conductor TRRS
(stereo-plus-mic) headphone for personal listening and sound
recording.

Ethernet Jack
The 10/100Mbps Ethernet port allows you to connect to other
computers/networks through a local area network (LAN).

24
Accessory Door
T10C User Guide
By removing the two long screws on top side of the system, allows
you to install optional snap-on module.
External Battery Connector
To install the external battery pack, install external battery holder
first and remove the cover of external battery connector before
snap the battery pack into the external battery connector.

Speaker
Integrated stereo speaker for sound and audio output for your
multimedia presentations or listening pleasure.



Protective Rubber
To prevent system harm from vibration or shock, the system is
designed with installing protective rubber on four corners.
DC-Jack
Lets you connect the AC power adapter in supplying continuous
power to your Tablet PC and recharging the battery.
The AC adapter provides external power source to your system
and charges the internal battery pack at the same time. The AC
adapter also has an auto-switching design that can connect to any
100VAC ~ 240VAC power outlets.
To connect the power adapter:
1. Plug the AC adapter connector to the DC-Jack socket on the
right side of the system.
2. Plug the power cord to the AC adapter.
Plug the other end of the power cord to a live wall
outlet, at the same time, the Power LED at front panel
lights up.
25
T10C User Guide
--
For the power supply of this equipment, an approved power
cord has
to be used.
--
Make sure the socket and any extension cord(s) you use can
support
the total current load of all the connected devices.
-- Remove all power from the device prior to installing or removing
any
accessories, hardware, or cables
--
Before cleaning the system, make sure it is disconnected
from
any external power supplies (i.e. AC adapter).

Docking Connector
Lets you connect the system to docking station to dock the tablet
PC when you are at home or office desk.
2.2.Preparing for Installation
Your T10C is designed and pre-configured for easy setup and use. This
section describes the installation steps you should follow to get the
system running as quickly as possible.
2.2.1.Switch ON the main battery
a. Main battery switch is located on rear side of
battery door
b. Adjust DIP switch to “ON”
26
yellow label
T10C User Guide
c. Place back the battery door
2.2.2.Plugging to the DC supply
The AC adapter provides external power source to your system and
charges the internal battery pack at the same time. The AC adapter
also has an auto-switching design that can connect to any 100VAC ~
240VAC power outlets.
To connect the power adapter:
3. Plug the AC adapter connector to the DC-Jack socket on the left
side of the system.
4. Plug the power cord to the AC adapter.
27
T10C User Guide
5. Plug the other end of the power cord to a live wall outlet, at the
same time, the Power LED at front panel lights up.
--
For the power supply of this equipment, an approved power cord has
to be used.
--
Make sure the socket and any extension cord(s) you use can support
the total current load of all the connected devices.
--
Remove all power from the device prior to installing or removing any
accessories, hardware, or cables
--
Before cleaning the system, make sure it is disconnected from
any external power supplies (i.e. AC adapter).
2.2.3.Starting Your System
The Power/Resume button is found on the right side of the Tablet PC.
Press the Power/Resume button to start your system and check that if
the Power LED turns on.
After a few seconds, the system’s display will turn on and your system
will begin to execute the Power On Self Test or POST to check if all
system components are running properly. Any error found during the
test will be displayed on the screen.
After the test, the screen will also display a message "press <F2> to
enter SETUP". You don’t need to run this program at the moment as
your dealer already made the necessary settings for your computer
28
T10C User Guide
optimal operation.
After the test has completed, your computer will start to search and
boot up the operating system from your hard drive.
2.2.4.Connecting the keyboard and mouse
Before setting up the system, please make sure the following items are
available.

Keyboard

Mouse (for system software installation)
A keyboard is an input device; a mouse is a pointing device. Please
connect these two devices as graphics shown below to interact with
your system.
29
T10C User Guide
Chapter 3
Using the T10C
3.1.Introduction
This chapter describes the basic features and procedures for using the
panel PC. It includes the I/O ports connecting and the touch screen
operation.
3.2.Using the USB Ports
USB (Universal Serial Bus) is a hardware interface that enables you to
connect multiple devices (such as printers, mice, keyboards, storage
devices, joysticks, digital cameras, and video conference cameras, etc.)
to your tablet pc and up to 127 devices can be attached.
Besides,
USB’s hot swap capability allows everything to be plugged in and
unplugged without turning the system off.
USB 2.0 is fully backward compatible, you will be able to use an USB
1.1 device in an USB 2.0 compliant system.
1. Connect the external device to the system.
2. The USB ports support hot plug-in connections. Install the device
driver before using the device.
30
T10C User Guide
3.3.Using the External Audio System
At the right side of your Tablet PC, you will find the built-in audio ports
for connecting Microphone jacks, earphone or powered speaker.
To connect to an audio jack:
1. Locate the audio ports (Microphone and Headphone) that you
want to use to the target device.
2. Plug the jack into the port on the right side of the system.
3.4.Installing the Battery (optional)
T10C provides optional external battery to extend the power of your
system.
For installing the battery pack, please follow the steps below:
1. Turn off the system.
2. Align the hook wall at the rear side, then place and screw it
securely.
3. Remove the cover of the external battery connector (as marked
 below) and place it on the lower position (as marked 
below).
31
T10C User Guide
4. Snap the battery pack into the external battery connector and
latch into the hook wall securely.
For removing the external battery, repeat the above steps in reverse
order to remove the battery.
3.5.Using a SIM Card
Your T10C can be equipped with a 3.5G module (optional) that can
work with SIM card. (SIM card is always working with 3.5G module.)
3.5.1.Inserting a SIM Card
To insert a SIM card into the SIM Card slot:
1. Turn off your System.
The T10C must be powered off while the SIM Card is being connected.
Otherwise, it is harmful to both devices and it shortens the life of these
devices.
2. Unscrew the optional accessory cover on top of the Tablet PC.
32
T10C User Guide
3. Make sure the clipped corner facing inward with the metallic label of
the card facing down. Push the SIM Card firmly but slowly into the
SIM Card slot.
To insert a SIM card into the slot, please pay attention only one correct
side can be accepted for the card slot. If you cannot insert the card into
the slot or you had inserted the card but it is not recognized by the Tablet
PC, please remove the card and insert it again. To prevent the damage
made both on card and the slot, never forced an entry into the slot with
incorrect side.
4. When the full length of the card is almost inside the slot, the SIM
Card will be automatically detected.
5. Place the optional accessory cover back to the place and screw it
firmly on top of the system.
3.5.2.Removing a SIM Card
To remove a SIM Card from the SIM Card slot:
1. Turn off your system.
2. Slightly push the SIM card to pop it out and pull it out directly. When
the SIM card has moved out a space out of the slot, hold the edges
of the card and slowly slide it out.
3.6. Using a Barcode Scanner Module
33
T10C User Guide
or MSR (optional)
The T10C System provides barcode scanner and MSR functions for your
optional selection, before installing either of these two modules on the top
side of the system, please remove the screws previously (illustrated in the
following graphics as indicated step 1).
To install the Barcode Scanner /MSR Module:
1. Make sure the system is turned off. Unscrew four screws from the
accessory door on top of the system.
2. Mount and secure the Barcode/MSR daughter board into
the mainboard with screws.
34
T10C User Guide
3. Insert FFC cable of barcode scanner into connector slot or
attached the MSR cable to the connectors on the daughter
board.
4. Screw to secure the Barcode Scanner/MSR onto the tablet.
35
T10C User Guide
Chapter 4
The BIOS Setup
Program
This system comes with a chip from Phoenix BIOS that contains the ROM
Setup information for your system. (This chip serves as an interface
between the processor and the rest of the system components.) This
section explains the information contained in the Setup program and tells
you how to modify the settings according to your system configuration.
The Setup utility program allows updates to the main board configuration
settings. The BIOS setup values will be saved in the CMOS. It is executed
when you change the system configuration, you change the system backup
battery, or the system detects a configuration error and asks you to run the
Setup program. You must have connected a USB type of keyboard, and
Use the arrow keys to select, and press Enter to run the selected program.
Function Key
Please check the following table for the function description of each
direction key.
Function
Key (s)
/
/
36
Function Description
Moves cursor left or right to select menu on
menu bar.
Moves cursor up or down to select items
T10C User Guide
Function
Key (s)
Function Description
+ / -
To change option for the selected items
<Tab>
To bring up the selected screen
To display the General Help screen
To load bios setup defaults value.
To save changes and exit the BIOS SETUP
UTILITY
To jump to the Exit Screen or exit the current
screen
<F1>
<F9>
<F10>
<ESC>
4.1.Main Screen Setup Utility
When you enter the BIOS SETUP UTILITY, the Main screen will appear
and display the system overview.
37
T10C User Guide
The Standard CMOS Setup screen is displayed above. Each feature
may have one or more option settings. Use the arrow keys to highlight
the feature you want to change and then use “”or “” to select the
value you want for that feature.
NOTE: The system BIOS automatically detects EC version, board
version, Processor, memory size, thus no changes are necessary.








38
System Date
To set the date, highlight the Date field and then press +/- keys to
set the current date. Follow the month, day and year format.
System Time
To set the time, highlight the Time field and then press +/- keys to
set the current time. Follow the hour, minute, and second format.
BIOS Version
The system will automatically displays the information of BIOS
version.
Build Time
The system will automatically displays the build time of BIOS.
EC Version
The system will automatically displays the information of EC
(Embedded Controller) firmware version.
VBIOS Version
The system will automatically displays the information of VBIOS
version of internal graphics.
Board Version
The system will automatically displays the information of PCB
version of mainboard.
Processor Type
The system will automatically displays the information of Processor
Type and speed.
T10C User Guide



System Memory Speed
The system will automatically displays the information of System
Memory Speed.
L2 Cache RAM
The system will automatically displays the information of L2 Cache
RAM.
Total Memory
The system will automatically displays the information of Total
Memory.
4.2.Advanced BIOS Features
For Advanced Settings, the BIOS will automatically display the Platform
information and let you define the configuration when system booting.
In this section, you may set the configurations for the following items:
Quick boot, UEFI boot, Legacy boot, and Boot Priority.
39
T10C User Guide




Select Language
Lets you select the language displayed in SETUP UTILITY. (The
current BIOS support the languages of English, Japanese and
French.)
UEFI Boot
Lets you activate or close the UEFI boot function by selecting
Enabled or Disabled option.
Legacy Boot
Lets you activate or close the Legacy boot function by selecting
Enabled or Disabled option.
Boot Priority
Lets you set the boot priority from UEFI boot or HDD boot.
4.3.Security Chip Configuration
40
T10C User Guide





41
Supervisor Password is:
This option displays the status of Supervisor Password. If the
password is entered, it will display “Set” information, or it will
display “Cleared” information when there is no password setting.
User Password is
This option displays the status of User Password. If the password is
entered, it will display “Set” information, or it will display “Cleared”
information when there is no password setting.
Set Supervisor Password
This field let you set or clear the Supervisor account’s password.
Set User Password
This field let you set or clear the User account’s password.
TPM Support
Lets you activate or close the TPM function by selecting Enabled or
Disabled option. (For the non-TPM SKU, this item will display “no
detected”.)
T10C User Guide
4.4.Boot Management Setup
This page allows you to set the search drive sequence where the
system will try to boot up first.
To select the boot device, you can use the up or down arrow key, then
press <+> to move up the device in the list or press <-> to move down
the device in the list. To exit from this menu, press <Esc>.
42
T10C User Guide
4.5.Exit Control




43
Exit Saving Changes
When you select this option, it will pop-out the following message,
“Save configuration changes and exit setup?” Select [OK] to save
the changes and exit the BIOS SETUP UTILITY.
Exit Discarding Changes
When you select this option, it will pop-out the following message,
“Discard changes and exit setup?”. Select [OK] to exit the BIOS
SETUP UTILITY without saving any changes.
Load Setup Defaults
When you select this option, it will pop-out the following message,
“Load optimal defaults?” Select [OK] to load the default values for
all the setup configurations.
Save Changes
When you select this option, it will pop-out the following message,
“Save changes?” Select [OK] to save all changes.
T10C User Guide
Chapter 5
User Interface for
T10C
5.1.Introduction
This user interface provides specific mobile utility to let you easily
setup some helpful functions and aware the system status directly.
This utility also let you adjust some function to fit the requirements,
such as brightness and volume adjustment, webcam launch, screen
orientation and monitor switching.
Furthermore, it also provides system information for your reference,
such as battery status, RF setting with its signal strength, firmware
(BIOS & EC) version information. Besides these features, you can
press the soft button to hibernate this device.
5.2.About the User Interface
5.2.1.Enable or disable the User Interface
To display the User Interface, please press the Fn button or point the
Hot key Utility on the screen.
To close the User Interface function, please press the
44
button on
T10C User Guide
the top right corner on this User Interface for disabling this utility from
the screen.
If there is no action took for this utility in 5 seconds, the UI screen will
close automatically.
5.2.3.System Status Information
This utility shows you the battery capacity status, RF status with its
signal strength and system information, and provides the control panel
for the function setting.
45
T10C User Guide
For battery capacity status:
The T10C is equipped with one internal battery and one optional
external battery.
The battery capacity status shown below advises you, that only one
internal battery is embedded with the system which is fully charged,
and there is no 2
nd
optional battery installed in the system.
If the system installs both the 1st internal battery and 2nd optional
battery, the illustration shown below indicates its current charging
status and capacity.
If 1st battery capacity drops to 15%, the system will display the
following warning message for 5 seconds.
46
T10C User Guide
For RF status:
The following RF status shows you that the system is equipped with
Wi-Fi, and Bluetooth functions. If you want to close either of these
functions, please refer section for how to disable it.
The following signal strength shows you that the Wi-Fi function is
connecting currently, the stronger the signal strength, the more scale
will show on the bar. If there is no module in the system, there will be
no status scale in the following status bar.
47
T10C User Guide
For System Information :
The system information shown on the left shows you the hotkey utility
version, BIOS and EC version and you can use them for customer
service when asked.
5.3.Using the Application
Your T10C has numbers of applications on the control panel for executing
specific command. It provides you to adjust brightness, volume, launch
webcam, make screen orientation and switch monitor.
5.3.1.Brightness Control
For brightness adjustment, press the Brightness
48
command.
T10C User Guide
When you press it, the brightness control panel is appeared as follows:

You can click
or
to reduce or increase the
brightness.

Also, you can slide the scale bar
to set the
brightness.

Since the system supports the light sensor, if you tick the
brightness Auto adjustment
, the screen
brightness will automatically adjust according to the operating
environment.
5.3.2.Volume Control
For Volume adjustment, press the Volume
49
command.
T10C User Guide
When you press it, the Volume control panel is appeared as follows:

You can click
or
to reduce or increase the audio
volume incrementally.

Also, you can slide the scale bar
to set the
audio volume.

You can tick the Mute
to mute the audio.
5.3.3.Webcam Launch
For Webcam Launch, press the Webcam
Webcam utility.
50
icon to launch the
T10C User Guide
5.3.4.Monitor Switch
For Monitor switch, press the Monitor Switch
to pop-up the
selection bar for choosing the display mode within following four
options.

You can click Duplicate
to display the same contents
both on the T10C screen and external display device. The
resolution on these two display modes are same, it is not
available to adjust the resolution on the external display mode.

You can click Extend
to display the different
contents on the T10C screen and external display device. You
only can adjust the resolution on the external display device.

51
You can click Projector only
to display on external
T10C User Guide
projector only.

5.3.5.RF Device ON/OFF Control
Press this soft button (via hotkey utility menu) to enable or disable
Wi-Fi, Bluetooth, WWAN, or GPS devices. When you press the RF
ON/OFF soft button, the screen pops-up the option list for your
selection.
You can see all functions in this option list have been ticked. To close
any device function, please touch the option to close the execution as
shown in the following graphics.
52
T10C User Guide
Disable Wi-Fi function
Disable WWAN function
Disable Bluetooth function
Disable GPS function
To activate the function, please again tick the option as shown in the
following graphics to make the device enable.
Activate Wi-Fi function
53
Activate Bluetooth function
T10C User Guide
Activate WWAN function
54
Activate GPS function
T10C User Guide
Chapter 6
Maintenance
Your T10C needs occasional cleaning to prolong their life. Please read
this section carefully to ensure proper care of T10C. When it is necessary
to clean it, use a soft, lint-free cloth, slightly dampened with a mild
detergent solution or use the contents of any commercially available
computer cleaning kit.
Never use petroleum-based solvents, or harsh detergents to clean the
system. Also never spray any liquids directly on the computer case or
screen. If the display screen has become smeared or dusty, clean the
screen by first applying a mild glass cleaner to a soft, clean, lint-free cloth,
and gently wipe the glass. Never apply liquids directly on the screen
surface. Moreover, do not use paper towels to clean the display screen.
Paper can scratch the display screen matte.
6.1.Maintaining the Battery

Do not expose heat or attempt to disassemble the battery, and
do not place the battery in water or in a fire.

Do not subject the battery to strong impact, such as a blow from
a hammer, or stepping on or dropping it.

Do not puncture or disassemble the battery.

Do not attempt to open or service the battery.

Replace only with batteries designed specifically for this product.

Keep the battery out of reach of children.
55
T10C User Guide

Dispose of used batteries according to local regulations.
6.2.Maintaining the LCD Display

Do not scratch the surface of the screen with any hard objects.

Do not spray liquid directly on the screen or allow excess liquid
to drip down inside the device.

Do not place anything, such as food and drink, on the screen at
any time to prevent damage to the screen.

Clean the LCD display only with a soft cloth dampened with
denatured alcohol or a proprietary LCD screen cleaner.
6.3.Cleaning the T10C

Turn off the T10C and unplug the power cord.

Wipe the screen and exterior with a soft, damp cloth moistened
only with water. Do not use liquid or aerosol cleaners on the
screen, as these will discolor the finish and damage the screen.
56
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement