Eizo | FlexScan L560T-CB | User`s manual | Eizo FlexScan L560T-CB User`s manual

Eizo FlexScan L560T-CB User`s manual
Important
Please read this User's Manual carefully to familiarize yourself with safe
and effective usage. Please retain this manual for future reference.
Wichtig
Bitte lesen Sie diese Bedienungsanleitung sorgfältig durch, um sich mit
dem sicheren und rationellen Betrieb dieses Produkts vertraut zu
machen. Bewahren Sie das vorliegende Handbuch zu Referenzzwecken
auf.
Important
Veuillez lire attentivement ce Manuel d'utilisation afin de vous familiariser
avec ce produit et de l'utiliser efficacement et en toute sécurité. Veuillez
conserver ce manuel pour référence ultérieure.
For U.S.A, Canada, etc. (rated 100-120 Vac) Only
FCC Declaration of Conformity
We, the Responsible Party
EIZO Inc.
5710 Warland Drive, Cypress, CA 90630
Phone: (562) 431-5011
declare that the product
Trade name: EIZO
Model: FlexScan L560T-CB
is in conformity with Part 15 of the FCC Rules. Operation of this product is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures.
* Reorient or relocate the receiving antenna.
* Increase the separation between the equipment and receiver.
* Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
* Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Note
Use the attached specified cable below or EIZO signal cable with this monitor so as to keep
interference within the limits of a Class B digital device.
- AC Cord
- Shielded Signal Cable (enclosed)
Canadian Notice
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de le classe B est comforme à la norme NMB-003 du Canada.
User’s Manual
Touch Panel Color LCD Monitor
It shall be assured that the final system is in compliance
to IEC60601-1-1 requirement.
English
SAFETY SYMBOLS
This manual uses the safety symbols below. They denote critical information. Please read them
carefully.
WARNING
Failure to abide by the information in a WARNING may result in serious injury and
can be life threatening.
CAUTION
Failure to abide by the information in a CAUTION may result in moderate injury
and/or property or product damage.
Indicates a prohibited action.
Indicates to ground for safety.
• This product has been adjusted specifically for use in the region to which it was originally
shipped. If operated outside this region, the product may not perform as stated in the
specifications.
• Power supplied equipment can emit electromagnetic waves, that could influence, limit or
result in malfunction of the monitor. Install the equipment in a controlled environment, where
such effects are avoided.
• This is a monitor intended for use in a medical imaging system. It does not support the
display of mammography images for diagnosis.
No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any
form or by any means, electronic, mechanical, or otherwise, without the prior written permission
of EIZO Corporation.
EIZO Corporation is under no obligation to hold any submitted material or information
confidential unless prior arrangements are made pursuant to EIZO Corporation's receipt of said
information. Although every effort has been made to ensure that this manual provides up-todate information, please note that EIZO monitor specifications are subject to change without
notice.
Mac OS is a registered trademark of Apple Inc.
Windows and Windows Vista are registered trademarks of Microsoft Corporation in the United
States and other countries.
VESA is a registered trademark or a trademark of Video Electronics Standards Association in
the United States and other countries.
EIZO, EIZO Logo, FlexScan and ScreenManager are registered trademarks of EIZO
Corporation in Japan and other countries.
All other company and product names are trademarks or registered trademarks of their
respective owners.
2
English
TABLE OF CONTENTS
PRECAUTIONS ....................................................................................... 4
1. INTRODUCTION ................................................................................... 10
1-1. Features ......................................................................................................10
1-2. Package Contents........................................................................................10
1-3. Controls & Connectors ..............................................................................11
2. CABLE CONNECTION ......................................................................... 13
2-1. Before connecting .......................................................................................13
2-2. Connecting the signal cable ........................................................................14
2-3. Touch Operation.........................................................................................16
2-4. Connecting two PCs to the monitor............................................................16
3. ScreenManager .................................................................................... 17
3-1. How to use the ScreenManager ..................................................................17
3-2. Adjustments and Settings ............................................................................18
3-3. Useful Functions .........................................................................................19
4. ADJUSTMENT ...................................................................................... 21
4-1. Screen Adjustment ......................................................................................21
4-2. Color Adjustment .......................................................................................24
5. ATTACHING A STAND .......................................................................... 26
6. TROUBLESHOOTING........................................................................... 27
7. SPECIFICATIONS ................................................................................. 31
8. GLOSSARY........................................................................................... 34
APPENDIX/ANHANG/ANNEXE .................................................................. i
TABLE OF CONTENTS
3
English
PRECAUTIONS
IMPORTANT
• This product has been adjusted specifically for use in the region to which it was
originally shipped. If the product is used outside the region, it may not operate as
specified in the specifications.
• To ensure personal safety and proper maintenance, please read carefully this section
and the caution statements on the monitor.
[Location of the Caution Statements]
[Symbols on the unit]
Symbol
This symbol indicates
Power button
Press to turn the monitor’s power on or off.
Alternating current
Alerting electrical hazard
Caution
Refer to SAFETY SYMBOLS section in this manual.
4
PRECAUTIONS
English
WARNING
If the unit begins to emit smoke, smells like something is burning, or
makes strange noises, disconnect all power connections immediately
and contact your dealer for advice.
Attempting to use a malfunctioning unit may result in fire, electric shock, or
equipment damage.
Do not open the cabinet or modify the unit.
Opening the cabinet or modifying the unit may result in fire, electric shock, or
burn.
Refer all servicing to qualified service personnel.
Do not attempt to service this product yourself as opening or removing covers
may result in fire, electric shock, or equipment damage.
Keep small objects or liquids away from the unit.
Small objects accidentally falling through the ventilation slots into the cabinet
or spillage into the cabinet may result in fire, electric shock, or equipment
damage.
If an object or liquid falls/spills into the cabinet, unplug the unit immediately.
Have the unit checked by a qualified service engineer before using it again.
Place the unit at the strong and stable place.
A unit placed on an inadequate surface may fall and result in injury or
equipment damage.
If the unit falls, disconnect the power immediately and ask your dealer for
advice. Do not continue using a damaged unit. Using a damaged unit may
result in fire or electric shock.
OK
Use the unit in an appropriate location.
Not doing so may result in fire, electric shock, or equipment damage.
* Do not place outdoors.
* Do not place in the transportation system (ship, aircraft, trains, automobiles,
etc.)
* Do not place in a dusty or humid environment.
* Do not place in a location where water is splashed on the screen (bathroom,
kitchen, etc.).
* Do not place in a location where the steam comes directly on the screen.
* Do not place near heat generating devices or a humidifier.
* Do not place in a location where the product is subject to direct sunlight.
* Do not place in an inflammable gas environment.
PRECAUTIONS
5
English
WARNING
To avoid danger of suffocation, keep the plastic packing bags away
from babies and children.
Use the enclosed power cord and connect to the standard power outlet
of your country.
Be sure to remain within the rated voltage of the power cord.
Not doing so may result in fire or electric shock.
Power Supply: 100-120/200-240 Vac 50/60Hz
To disconnect the power cord, grasp the plug firmly and pull.
Tugging on the cord may damage and result in fire or electric shock.
The equipment must be connected to a grounded main outlet.
Failure to do so may result in fire or electric shock.
Use the correct voltage.
* The unit is designed for use with a specific voltage only. Connection to
another voltage than specified in this User’s Manual may cause fire, electric
shock, or equipment damage.
Power Supply: 100-120/200-240 Vac 50/60Hz
* Do not overload your power circuit, as this may result in fire or electric
shock.
Handle the power cord with care.
* Do not place the cord underneath the unit or other heavy objects.
* Do not pull on or tie the cord.
If the power cord becomes damaged, stop using it. Use of a damaged cord
may result in fire or electric shock.
For the electrical safety, do not connect or disconnect the power cord
in the presence of patients.
Never touch the plug and power cord if it begins to thunder.
Touching them may result in electric shock.
When attaching an arm stand, please refer to the user’s manual of the
arm stand and install the unit securely.
Not doing so may cause the unit to become unattached, which may result in
injury or equipment damage. Before installation, make sure that desks, walls,
and others an arm stand is fixed on have adequate mechanical strength.When
the unit is dropped, please ask your dealer for advice. Do not continue using a
damaged unit. Using a damaged unit may result in fire or electric shock. When
reattaching the tilt stand, please use the same screws and tighten them
securely.
6
PRECAUTIONS
OK
English
WARNING
Do not touch a damaged LCD panel directly with bare hands.
The liquid crystal that may leak from the panel is poisonous if it enters the
eyes or mouth.
If any part of the skin or body comes in direct contact with the panel, please
wash thoroughly.
If some physical symptoms result, please consult your doctor.
Fluorescent backlight lamps contain mercury (the products that have
LED backlight lamps contain no mercury), dispose according to local,
state or federal laws.
Exposure to elemental mercury can result in effects on the nervous system,
including tremor, memory loss, and headache.
CAUTION
Handle with care when carrying the unit.
Disconnect the power cord and cables when moving the unit. Moving the unit
with the cord attached is dangerous. It may result in injury.
When handling the unit, grip the bottom of the unit firmly with both
hands ensuring the panel faces outward before lifting.
Dropping the unit may result in injury or equipment damage.
OK
Do not block the ventilation slots on the cabinet.
* Do not place any objects on the ventilation slots.
* Do not install the unit in a closed space.
* Do not use the unit laid down or upside down.
Blocking the ventilation slots prevents proper airflow and may result in fire,
electric shock, or equipment damage.
Do not touch the plug with wet hands.
Doing so may result in electrical shock.
Use an easily accessible power outlet.
This will ensure that you can disconnect the power quickly in case of a
problem.
Periodically clean the area around the plug.
Dust, water, or oil on the plug may result in fire.
Unplug the unit before cleaning it.
Cleaning the unit while it is plugged into a power outlet may result in electric
shock.
PRECAUTIONS
7
English
CAUTION
If you plan to leave the unit unused for an extended period, disconnect
the power cord from the wall socket after turning off the power button
for the safety and the power conservation.
This product is only suitable for a patient environment, but not for
contact with a patient.
Notice for this monitor
This product is suited to general purposes like creating documents, viewing multimedia content.
This product may not be covered by warranty for uses other than those described in this manual.
The specifications noted in this manual are only applicable when the following are used:
• Power cords provided with the product
• Signal cables specified by us
Only use optional products manufactured or specified by us with this product.
As it takes about 30 minutes for the performance of electrical parts to stabilize, adjust the
monitor 30 minutes or more after the monitor power has been turned on.
Monitors should be set to a lower brightness to reduce changes in luminosity caused by long-term
use and maintain a stable display.
When the screen image is changed after displaying the same image for extended periods of time,
an afterimage may appear. Use the screen saver or power save function to avoid displaying the
same image for extended periods of time.
Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation
lifetime. (Refer to “Cleaning” on the next page.)
The LCD panel is manufactured using high-precision technology. Although, missing pixels or lit
pixels may appear on the LCD panel, this is not a malfunction. Percentage of effective dots:
99.9994% or higher.
The backlight of the LCD panel has a fixed life span. When the screen becomes dark or begins to
flicker, please contact your dealer.
Do not scratch or press on the panel with any sharp objects, as this may result in damage to the
panel. Do not attempt to brush with tissues as this may scratch the panel.
When the monitor is cold and brought into a room or the room temperature goes up quickly, dew
condensation may occur on the interior and exterior surfaces of the monitor. In that case, do not
turn the monitor on. Instead wait until the dew condensation disappears, otherwise it may cause
some damage to the monitor.
8
PRECAUTIONS
English
Cleaning
Attention
• Chemicals such as alcohol and antiseptic solution may cause gloss variation, tarnishing, and
fading of the cabinet or panel, and also quality deterioration of the image.
• Never use any thinner, benzene, wax, and abrasive cleaner, which may damage the cabinet or
panel.
• Do not allow liquid to enter the clearance between the panel and the panel frame.
NOTE
• The optional ScreenCleaner is recommended for cleaning the panel surface.
If necessary, the stains on the cabinet and panel surface can be removed by moistening part of a
soft cloth with water.
To use the monitor comfortably
An excessively dark or bright screen may affect your eyes. Adjust the brightness of the monitor
according to the environmental conditions.
Staring at the monitor for a long time tires your eyes. Take a 10-minute rest every hour.
PRECAUTIONS
9
English
1. INTRODUCTION
Thank you very much for choosing an EIZO Color Monitor.
1-1. Features
• Dual inputs compliant
• DVI (p.34) Digital input (TMDS (p.35)) compliant.
• Horizontal scanning frequency:
Vertical scanning frequency:
Resolution:
Analog input 30 - 81 kHz
Digital input 30 - 65 kHz
Analog input 49.5 - 75.5 Hz
Digital input 59 - 61 Hz (VGA TEXT: 70 Hz)
1 M pixels (1280 dots x 1024 lines)
• Auto Adjustment compliant
• Support to sRGB (p.35) standard
• The height adjustable stand incorporated
• Touch Panel provided (USB serial communication)
• Touch Panel Pointer “TP1” is available (optional, p.16)
1-2. Package Contents
Please contact your local dealer for assistance if any of the listed items are missing or
damaged.
• LCD Monitor
• Power Cord
• Signal Cable (MD-C87)
• USB Cable (MD-C93)
• User’s Manual
• ScreenManager Quick Reference
• LIMITED WARRANTY
• Recycling Information
• EIZO Touch Panel Disk (CD-ROM)
(Contents: MT 7 (Touch Panel Driver), Installation Guide)
NOTE
• Please retain the packing materials for future transference.
• For the touch panel driver installation procedure and cautions, refer to the
Installation Guide on the CD-ROM.
10
1. INTRODUCTION
English
1-3. Controls & Connectors
Front
(1)
Control Panel
SIG.
AUTO
ENT.
(2) (3) (4)
(5)
(1) ScreenManager®
(6)
(7)
Monitor Adjustment menu (p.17).
(2) SIG.
Input Signal
Selection Button
Switch the input signals when connecting 2
PCs (p.16).
(3) AUTO
Auto Adjustment
Button
Adjust the screen to appropriate condition
automatically(analog input only).
(4) ENT.
Enter Button
Show the ScreenManager on the screen.
Confirm the setting / adjustment function.
Save the adjustment values.
(5)
Control Buttons
(Left, Down, Up,
Right)
Select the desired function.
Increase and decrease the adjustment value.
(6)
Power Button
Turns the power on or off.
(7)
Power Indicator
Indicate monitor’s operation status.
Blue: Operating
Flashing blue: Last 15 min. of operation
time before entering the power off state.
(p.19)
Flashing orange slowly: Power off
1. INTRODUCTION
11
English
Rear
(8)
219'4
+0276
&8+
219'4
&57$
+0276
&8+
&57$
(10)
(9)
Bottom
(11)
12
(12) (13) (14)
(8) Hole for TP1
Hole for installing the lead of the TP1
(Optional Touch Panel Pointer).
(9) Stand (Detachable)
The LCD monitor can be used with an other
stand by removing the stand (p.26).
(10)
Security Lock Slot
Allows for connection of a security cable.
This lock supports Kensington’s MicroSaver
security system.
(11)
Power Connector
(POWER INPUT)
Connect the power cord.
(12)
DVI-D Connector
(DVI)
Connect the optional digital cable.
(13)
D-Sub mini 15 pin
Connector (D-SUB)
Connect the enclosed analog cable
(MD-C87).
(14)
USB port
Connect the enclosed touch panel cable
(MD-C93).
1. INTRODUCTION
English
2. CABLE CONNECTION
2-1. Before connecting
Before connecting your monitor to the PC, change the display screen settings (resolution
(p.35) and frequency) in accordance with the charts below.
NOTE
• The lower display modes like 640x 480, automatically enlarge to the maximum
display mode (1280 x 1024), and some lines of the characters may become fuzzy. In
this case, use <Smoothing> function (p.23) to make the lines clear.
• When your computer and display support VESA DDC, the suitable resolution and
the refresh rate are set by just plugging your display into the computer without any
manual settings.
Analog Input
Resolution
Frequency
320 x 200
640 x 480
720 x 400
800 x 600
1024 x 768
1152 x 864
1280 x 960
1280 x 1024
70 Hz
~75 Hz
70 Hz
~75 Hz
~75 Hz
75 Hz
60 Hz
~75 Hz
Dot Clock
Remarks
135 MHz (Max)
VGA Graphics
VGA, VESA
VGA TEXT
VESA
VESA
VESA
VESA
VESA
Digital Input
Resolution
Frequency
Dot Clock
Remarks
640 x 480
720 x 400
800 x 600
1024 x 768
1280 x 1024
60 Hz
70 Hz
60 Hz
60 Hz
60 Hz
109 MHz (Max)
VGA
VGA TEXT
VESA
VESA
VESA
2. CABLE CONNECTION
13
English
2-2. Connecting the signal cable
NOTE
• Be sure that the powers of the PC and the monitor are OFF.
1.
Plug the signal cable into the connector at the rear of the monitor
and the other end of the cable into the video connector on the PC.
After connecting, secure the connection with the screw-in fasteners.
Digital Signal Input Connecter Analog Signal Input Connecter
2. Power Cord
1. Signal Cable
5. USB Cable
Analog Input
Signal Cable
Signal Cable (enclosed, MDC87)
Connector of PC
Video Output Connector/ D-Sub mini 15 pin
Input Connector (monitor)/ D-Sub mini 15 pin
Digital Input
Signal Cable
FD-C39 (Optional)
14
2. CABLE CONNECTION
Connector of PC
Video Output Connector DVI-I
Input Connector (monitor)/ DVI
English
2.
Plug the power cord into the power connector on the rear of the
monitor. Then, plug the other end of the cord into a power outlet.
WARNING
Use the enclosed power cord and connect to the standard
power outlet of your country.
Be sure to remain within the rated voltage of the power cord.
Not doing so may result in fire or electric shock.
Power Supply: 100-120/200-240 Vac 50/60Hz
The equipment must be connected to a grounded main
outlet.
Failure to do so may result in fire or electric shock.
3.
Turn on the monitor’s main power and then switch on the PC's
power.
The monitor’s power indicator will light up (blue).
If an image does not appear, refer to the “6. TROUBLESHOOTING” (p.27) for
advice.
4.
Install the touch panel driver according to the instructions included
in the EIZO Touch Panel Disk (CD-ROM).
NOTE
• For the touch panel driver installation procedure and cautions, refer to the
Installation Guide on the CD-ROM.
5.
Connect the upstream port of the monitor to the downstream port of
the USB compliant PC by using the USB cable (MD-C93).
After connecting the USB cable, the USB function can be set up automatically.
NOTE
• Do your part to conserve energy, turn off the monitor when you are finished using it.
Disconnecting the monitor from the power supply is recommended to save energy
completely.
• Adjust brightness of the screen depending on the brightness of your environment (p.
24). Too dark or too bright of a screen can cause eyestrain.
• Be sure to take adequate rests. A 10-minute rest period each hour is suggested.
2. CABLE CONNECTION
15
English
2-3. Touch Operation
Point and touch with one finger only.
NOTE
• Do not touch the screen while turning on the PC and the monitor. Touch the screen
five seconds later after appearing the image.
• Touch the screen five seconds later after connecting the USB cable.
• For the users with gloves, we recommend to use touch panel pointer, “TP1”
(optional). Regarding the installation, please refer to the User’s Manual of TP1.
2-4. Connecting two PCs to the monitor
Two PCs can be connected to the monitor through the DVI and the D-Sub mini 15 pin
connector on the back of the monitor.
NOTE
• The touch panel operation is effective for one computer only.
Selecting the active input
The Input Signal Selection Button on the control panel can be used to select either Signal
1 or Signal 2 as the active input at any time. Every time the Input Signal Selection
Button is pressed, the input changes. When switching the signal, the kind of the input
signal (Analog or Digital) is displayed for a few seconds on the right top corner of the
screen.
Input Signal Selection Button
16
2. CABLE CONNECTION
SIG.
AUTO
ENT.
English
3. ScreenManager
3-1. How to use the ScreenManager
ScreenManager
Main Menu
Control Buttons
Left, Down, Up, Right
Auto Adjustment Enter Button
Button
1.
Entering the ScreenManager
Press the Enter Button once to display the main menu of the ScreenManager.
2.
Making Adjustments and Settings
(1) Select the desired sub menu icon using the Control Buttons and press the Enter
Button. The sub menu appears.
(2) Use the Control Buttons to select the desired setting icon and press the Enter
Button. The setting menu appears.
(3) Use the Control Buttons to make all required adjustments and press the Enter
Button to save the settings.
3.
Exiting the ScreenManager
(1) To return to the main menu, select the <Return> icon or press the Down
Button twice, followed by the Enter Button.
(2) To exit the ScreenManager, select <Exit> icon or press the Down Button twice,
followed by the Enter Button.
NOTE
• Double clicking the Enter Button at any time also exits the ScreenManager menu.
3. ScreenManager
17
English
3-2. Adjustments and Settings
The following table shows all the ScreenManager’s adjustment and setting menus.
“*” indicates adjustments of analog input only.
Main menu
Screen
Sub menu
Reference
Clock
*
Phase
*
Position
*
Range Adjustment
*
4-1. Screen Adjustment (p.21)
Smoothing
Color
Brightness
4-2. Color Adjustment (p.24)
Color Mode
• Custom
Temperature
Gamma
Gain
Reset
• sRGB
Others
*1
18
Input Signal
Set the input signal selection of
automatic or manual (p.20)
Off Timer
Set the power save (p.19)
VGA Selection
Select the display mode. (p.28)
Menu Position
Adjust the menu position.
Translucent
Set the transparency of the menu.
Menu Off Timer
Set the menu displaying time.
Reset
Return to the factory default settings.
(p.32)
Information
Information
Review the ScreenManager’s settings,
model name, serial number and usage
time*1.
Language
English, German,
French, Spanish,
Italian, Swedish and
Japanese
Select the ScreenManager’s language.
Due to the inspection on the factory, the usage time may not “0 hour” at shipping.
3. ScreenManager
English
3-3. Useful Functions
Adjustment Lock
Use the “Adjustment Lock” function to prevent any accidental changes.
Locked function
• Adjustments and settings in the ScreenManager
• Auto Adjustment Button
Unlocked function
• Adjustment of brightness by the Control Buttons
• Input Signal Selection Button
[To lock]
(1) Turn off the monitor’s power by the power button on the control panel.
(2) Press on the Auto adjustment button while switching on the monitor’s power.
[To unlock]
(1) Turn off the monitor’s power by the power button on the control panel.
(2) Hold down the Auto adjustment button once again and turn the power back on.
Off Timer
The off timer function causes the monitor to automatically enter a power off state after
a predetermined amount of time has lapsed. This function was created to reduce
afterimage characteristics that are particular to LCD monitors when the monitor screen
is left on for a long period without use.
[Procedure]
(1) Select <Off Timer> in the ScreenManager <Others> menu.
(2) Select “Enable” and press the Right and Left Buttons to adjust the “On Period” (1
to 23 hours).
[Off timer system]
Timer
Monitor
Power Indicator
On Period (1H - 23H)
Operation
Blue
Last 15 min. in “On period”
Advance Notice *1
Blue Flashing
“On period” expired
Power off
Flashing orange slowly
*1
Advance notice (Power Indicator flashing blue) will be given 15 minutes before the monitor
automatically enters the “Power Off” mode. Pressing the power button during the advanced
notice period can reset “On Period” for another 90 minutes. It is possible to reset “On Period”
as many times as needed.
[Power Resumption Procedure]
Press the power button to return a normal screen.
3. ScreenManager
19
English
EIZO Logo display
Enables to display the EIZO logo for a while when switching on the monitor (Default is
no logo). If you desire to display or undisplay this logo, use this function.
[To display]
(1) Turn off the monitor’s power by the Power button on the control panel.
(2) Hold down the Enter button once again and turn the power back on.
[To undisplay]
(1) Turn off the monitor’s power by the Power button.
(2) Hold down the Enter button once again and turn the power back on.
Automatically selecting the input signal function
The monitor will automatically detect the inputted signal of either the connection for
display.
Connecting two PCs to the monitor
When the one computer is switched off, the monitor will automatically dislay the other
signal.
Use the ScreenManager to switch the input selection to manual.
[Procedure]
(1) Select <Input Signal> in the <Others> menu.
(2) Select “Manual”.
20
3. ScreenManager
English
4. ADJUSTMENT
When digital signals are input, images are displayed correctly based on the
preset data of the monitor, but if characters and/or lines appear blurred, go to
step 5 [Smoothing]. When performing more advanced adjustment, see “4-2.
Color Adjustment” (p.24) and subsequent pages.
4-1. Screen Adjustment
Screen adjustments for the LCD monitor should be used in suppressing screen flickering
and also for adjusting the screen to its proper position. There is only one correct
position for each display mode. It is also recommended to use the ScreenManager
function when first installing the display or whenever changing the system.
Adjustment Procedure
NOTE
• Allow the LCD monitor to stabilize for at least 30 minutes before making image
adjustments.
1.
Press the Auto Adjustment Button on the control panel.
The message “Your setting will be lost, if you press again now.” appears and
remains on the screen for 5 seconds. While the message is on the screen, press the
Auto Adjustment Button again to automatically adjust the clock, phase, and screen
position. If you do not wish to do adjust the screen, do not press the Auto
Adjustment Button again.
NOTE
• The Auto Adjustment function is intended for use on AT-compatible PC running
Windows. It may not work properly in either of the following cases.
When running an AT-compatible PC on MS-DOS (Not windows).
The background color for the wall paper" or "desktop" pattern is set to black.
If the appropriate screen can not be made by using the Auto Adjustment
Button, adjust the screen through the following procedures. If the
appropriate screen can be made, proceed to step 4.
4. ADJUSTMENT
21
English
2.
We recommend setting the desktop pattern to that as shown in the
diagram below.
NOTE
• More precise adjustment is available for using the “Screen Adjustment
program” software. It can be downloaded from the EIZO homepage
(http://www.eizo.com).
3.
Adjust by using <Screen> menu in the ScreenManager.
(1) Vertical bars appear on the screen
Use the <Clock> (p.34) adjustment.
→
Select the <Clock> and eliminate the vertical bars by using the Right and Left
of the Control Buttons.
Do not continuously press the Control Buttons, as the adjustment value will
change quickly and make it difficult to locate the most suitable adjustment
point. If the horizontal flickering, blur or bars appear, proceed to <Phase>
adjustment as follows.
(2) Horizontal bars appear on the screen.
Use the <Phase> (p.34) adjustment.
→
Select the <Phase> and eliminate the horizontal flickering, blurring or bars by
using the Right and Left Buttons.
NOTE
• Horizontal bars may not completely disappear from the screen depending on
the PC.
22
4. ADJUSTMENT
English
(3) The screen position is incorrect.
→
Use the <Position> adjustment.
The correct displayed position of the monitor is decided because the number
and the position of the pixels are fixed. The “Position” adjustment moves the
image to the correct position.
Select <Position> and adjust the position by using the Up, Down, Right and
Left Buttons.
If vertical bars of distortion appear after finishing the <Position> adjustment,
return to <Clock> adjustment and repeat the previously explained adjustment
procedure. Clock→ Phase→ Position
4.
To adjust the output signal range (Dynamic Range) of the signal.
→
Use the <Range Adjustment> (p.34).
This controls the level of output signal range to display the whole color gradation
(256 colors).
[Procedure]
Press the Auto Adjustment Button on the control panel while displaying the
<Range Adjustment> menu to automatically adjust the range. The screen blanks
for a moment, and adjusts the color range to display the whole color gradation of
the current output signal.
5.
To smooth the blurred texts of the enlarged screen of the lower
resolutions.
Switch the <Smoothing> setting.
→
<Smoothing> is clear-cut the letters or lines.
Select <Smoothing> in the screen menu and select the suitable level from 1 ~ 5.
NOTE
• The “Smoothing” is disabled in the resolution 1280 x 1024.
• Since the displayed image is enlarged, the blurred texts may not be
necessarily lost completely.
4. ADJUSTMENT
23
English
4-2. Color Adjustment
In the analog input, perform the “Range Adjustment” (p.23) before making the
color adjustments.
The <Color> menu in the ScreenManager enables to change the color of the screen. By
using the <Color Mode>, the adjustment mode can be selected from <Custom> mode (to
adjust the color settings according to your preference) and <sRGB> mode.
NOTE
• Allow the LCD monitor to stabilize for at least 30 minutes before making image
adjustments. (Allow the monitor to warm up for at least 30 minutes before making
adjustments.)
• Performing the <Reset> of the <Color> menu returns the color settings to the
default settings.
• The values shown in percentages represent the current level within the specific
adjustment. They are available only as a reference tool. (To create an uniform white
or black screen, the percentages for each will probably not be the same.)
Adjustment Contents
Menu
Brightness
Color Mode
Custom
sRGB
√
√
Function Descriptions
To set the brightness of the
screen
Adjustable range
0 ∼ 100%
NOTE
• The values shown in the “%” are available only as
reference.
• Direct pressing the up and down control button also
can adjust the brightness (When ScreenManager
does not appear.). After the adjustment, press Enter
button to save the data.
Temperature
(p.34)
√
-
To set the color temperature
4000 ∼ 10000 K
in 500 K increments
(including 9300 K).
NOTE
• The values shown in the Kelvin are available only as a
reference tool.
• While color temperature is adjusted, <Gain> is
adjusted automatically according to the color
temperature.
• Setting the temperature under 4000 K or over 10000 K
invalidates the color temperature setting. (The color
temperature’s setting turns “Off”.)
• Setting the <Gain> invalidates the <Temperature>
adjustment.
24
4. ADJUSTMENT
English
Menu
Gamma
(p.34)
Color Mode
Custom
sRGB
√
-
Function Descriptions
To set the gamma value
Adjustable range
1.8 ∼ 2.6
NOTE
• If setting the gamma value, the using the monitor in
the digital signal input is recommended.
If using the monitor in the analog input signal, set the
gamma value from 1.8 to 2.2.
NOTE
• The <Hue> adjustment may cause undisplayable color
tone.
Gain (p.34)
√
-
To change each color (red,
green and blue)
0 ∼ 100%
By adjusting the red,
green and blue color
tones for each mode,
custom colors can be
defined. Display a
white or gray
background image and
adjust the <Gain>.
NOTE
• The values shown in the percentage are available only
as a reference tool.
• Setting the <Temperature> (p.34) invalidates the
<Gain> adjustment. The <Gain> setting varies with
color temperature.
Reset
√
-
To return the color settings
to the default settings
Select the <Reset>.
4. ADJUSTMENT
25
English
5. ATTACHING A STAND
The LCD monitor can be used with other stand by removing the tilt stand and attaching
the stand to the LCD monitor.
NOTE
• When attaching an arm or stand, follow the instructions of their user’s manual.
• When using another manufacturer’s arm or stand, confirm the following in advance
and select one conforming to the VESA standard.
- Clearance between the screw holes: 100 mm x 100 mm
- Thickness of plate: 2.6 mm
- Strong enough to support weight of the monitor unit (except the stand) and
attachments such as cables.
• Attach an arm or stand to meet the following tilt angles of the monitor.
- Up 45 degrees, down 0 degrees (Within operating range)
• Please connect cables after attaching a stand.
Setup Procedure
1.
Lay the LCD monitor down. Do not scratch the panel.
2.
Remove the tilt stand by loosening the 4 screws.
3.
Attach a stand to the LCD monitor securely with the same screws.
stand
4 Mounting Screws: M4 x 12 mm
26
5. ATTACHING A STAND
English
6. TROUBLESHOOTING
If a problem persists even after applying the suggested remedies, contact an EIZO dealer. The
latest FAQ information is supplied on EIZO homepage (http://www.eizo.com).
•
No Picture Problems
Problems
1. No picture
• Indicator status: Off
• Indicator status: Blue
• Indicator status: Orange Flashing
Points to check with possible solutions
Check that the power cord is correctly
connected. If the problem persists, turn off the
monitor power for a few minutes, then turn it
back on and try again.
Check the “Brightness” setting.
Switch the signal input by pressing the Input
Signal Selection Button on the front control
panel.
Try pressing the power button.
These message appear when the signal is not
2. Following messages appear.
(Error messages shown below will inputted correctly, even if the monitor functions
properly.
remain on the screen for 40
seconds.)
When the image is displayed correctly after a
short time, there is no problem with the
monitor. (Some PCs do not output the signal
soon after powering on.)
Check that the PC is turned ON.
Check that the signal cable is properly
connected to the PC or graphics board.
Switch the signal input by pressing the Input
Signal Selection Button on the front control
panel.
• The message below shows that the
input signal is out of the specified
frequency range. (Such signal
frequency is displayed in red.)
Check whether the signal setting of your PC
matches the resolution and the vertical
frequency settings for the monitor(p.13).
Reboot the PC.
Select an appropriate display mode using the
graphics board’s utility. Refer to the manual of
the graphics board for details.
fD: Dot Clock
(Displayed only when the digital signal inputs)
fH: Horizontal Frequency
fV: Vertical Frequency
6. TROUBLESHOOTING
27
English
•
Imaging problems
Problems
Points to check with possible solutions
3. Display position is incorrect.
Adjust the image position using the <Position>
(p.23)
The two display modes, VGA 720 x 400 (70
Hz) and 320 x 200 (70 Hz), have the same
signal timings. Using this adjustment selects the
appropriate display mode. (This function effects
only when the resolution is VGA 720 x 400 (70
Hz) or 320 x 200 (70 Hz).
If the problem persists, use the graphics board’s
utility software to change the display position if
available.
4. Vertical bars of distortion appear.
Decrease the vertical bars using the <Clock>.
(p.22)
5. Horizontal bars of distortion
appear.
Decrease the horizontal bars using the <Phase>.
(p.22)
6. Letters and lines appear blurred.
Switch the <Smoothing> mode. (p.23)
7. The screen is too bright or too
dark.
Adjust the <Brightness> (The backlight of the
LCD monitor has a fixed life span. When the
screen becomes dark or begins to flicker, please
consult your dealer.)
8. Afterimages appear.
Do you use the screen saver or timer (p.19)
when displaying the same image for extended
periods of time?
Afterimages are particular to LCD monitors.
Avoid displaying the same image for extended
periods of time. (p.19)
9. The screen has defective pixels
(e.g. slightly light or dark).
This is due to the characteristics of the panel
itself, and not the LCD product.
28
6. TROUBLESHOOTING
English
•
Other problems
Problems
Points to check with possible solutions
10.The <Smoothing> cannot be
selected.
<Smoothing> is disabled when the screen is
displayed in the 1280 x 1024.
11.The Enter Button does not
operate.
The adjustment lock is probably on. To unlock:
switch the LCD monitor off. Then, while
pressing the Auto Adjustment Button switch,
the power on. (p.19)
12.The Auto Adjustment Button does
not operate.
The adjustment lock is probably on. To unlock:
switch the LCD monitor off. Then, while
pressing the Auto Adjustment Button switch,
the power on. (p.19)
The Auto adjustment function is intended for
use on the AT-compatible PC running Windows.
It may not work properly in either of the
following cases.
• When running an AT-compatible PC on MSDOS (Not Windows).
• The background color for the “wall paper”
or “desktop” pattern is set to black.
Some signals from a graphics board may not
function properly.
6. TROUBLESHOOTING
29
English
•
Touch Panel Problems
Problems
Points to check with possible solutions
13.Cursor is jittery. / Drawing lines
are not straight and smooth.
The influence of metal may cause jittery cursor.
When multiple monitors are placed close to
each other, leave space between monitors.
14.Cursor position is not correct. /
Cursor jumps.
When cursor position is incorrect or cursor
jumps, turn off and on the monitor. If the
symptom is not improved, perform the
calibration on the monitor.
• Do not touch the screen while turning on the
PC and the monitor. Touch the screen five
seconds later after appearing the image.
• Touch the screen five seconds later after
connecting the USB cable.
• Changing the position or angle of the
monitor will cause cursor jump.
The drawing touch and dragging the finger on
the touch panel to draw the picture may cause
incorrect cursor position.
Keep metals away from the panel surface.
Touch with one finger only. Keep other fingers
away from the touch screen. Do not rest the
hand in the monitor or bezel while touching the
screen.
The spray for preventing static electricity may
infl uences the sensibility of the touch panel. Do
not use it on cleaning.
15.No touch sound.
30
6. TROUBLESHOOTING
Under Windows 7, touch sound is only output
through the audio output terminal of the PC. To
hear touch sound, connect speakers.
The touch sound may not be output from the
external line out of the PC depending on the
hardware configuration.
English
7. SPECIFICATIONS
LCD Panel
43 cm (17.0 inch), TFT color LCD panel with Anti-Glare Hard
Coating, Viewing Angle: H: 178°, V: 178° (CR≥10)
Dot Pitch
0.264 mm
Horizontal Scan Frequency
Analog: 30 ~ 81 kHz (Non-interlace)
Digital: 30 ~ 65 kHz
Vertical Scan Frequency
Analog: 49.5 ~ 75.5 Hz (Non-interlace)
Digital: 59 ~ 61 Hz, (VGA TEXT : 70Hz)
Resolution
1 M pixels (1280 dots x 1024 lines)
Dot Clock (Max.)
Analog: 135 MHz
Digital: 109 MHz
Display Colors
16.77 million colors (max.)
Display Area
337.9 mm (H) x 270.3 mm (V) (13.3” (H) x 10.6” (V))
(Viewable image size: 432 mm (17.0”))
Touch Panel
OS
Microsoft Windows 7 (32 bit/64 bit)
Microsoft Windows Vista Service Pack 2 (32 bit)
Microsoft Windows XP Service Pack 3 (32 bit)
(Not compatible with Mac OS)
Communication USB
protocol
Communication Full speed
Speed
Detective
Analog capacitive technology, finger touch
method
Power Supply
100-120/200-240 VAC±10%, 50/60 Hz,
0.55-0.5 A/0.35-0.3 A
Power Consumption
Max.: 32 W
Input Connector
D-Sub mini 15 pin, DVI-D
Analog Input Signal (Sync)
Separate, TTL, Positive/Negative
Analog Input Signal (Video)
0.7Vp-p/75Ω Positive
Input Signal (Digital)
TMDS (Single Link)
Signal registration
Analog: 45 (Factory preset: 16)
Plug & Play
VESA DDC 2B / EDID structure 1.3
Dimensions
with stand
380 mm (W) x 432.5 ~514.5mm(H) x 208.5 mm (D)
(15.0”(W) x 17.0” ~ 20.3”(H) x 8.2”(D))
without stand
380 mm (W) x 353 mm (H) x 58 mm (D)
(15.0”(W) x 13.9”(H) x 2.28” (D))
Weight
with stand
8.2 kg (18.1 lbs.)
without stand
5.2 kg (11.5 lbs.)
Environment
Temperature
Operating: 0 °C ~ 35 °C (32 °F ~ 95 ° F)
conditions
Transportation/Storage: -20 °C ~ 60 °C (-4 °F ~ 140 ° F)
Humidity
Operating: 20% to 80% R.H. Non-condensing
Transportation/Storage: 10% to 80% R.H. Non-condensing
Pressure
Operating: 700 hPa to 1060 hPa
Transportation/Storage: 200 hPa to 1060 hPa
7. SPECIFICATIONS
31
English
Classification of Equipment
Type of protection against electric shock : Class I
EMC class : EN60601-1-2:2007 Group1 Class B
Classification of medical device (MDD 93/42/EEC) : Class I
Mode of operation : Continuous
IP Class : IPX0
Default settings
Brightness
100%
Smoothing
3
Temperature
Off (normal white: approx. 6500 K)
Input Signal
Auto
Off Timer
Disable
Language
English
Optional
Touch Panel Pointer
TP1
Signal Cable
FD-C39
Cleaning kit
EIZO “ScreenCleaner”
Dimensions
#761
'06
33.5 35.5(1.4)
(1.32)
140(5.5)
346.2(13.6)
322.2(12.7)
168(6.6)
301.5(11.9)
67.5
(2.66)
272.2(10.7)
160(6.3)
193(7.6)
272.5(10.7)
432.5(17.0)
5+)
TILT
:40˚
58(2.28)
56.9
353(13.9)
23.9(0.94)
20.1
(0.79)
82(3.23)
( )
380(15.0)
339.8(13.4)
20.1
(0.79)
Unit:mm (inches)
35˚
35˚
SWIVEL
(325.5(12.8))
32
7. SPECIFICATIONS
208.5(8.2)
English
Pin Assignment
D-Sub mini 15 pin connector
3
4
5
10
15
9
1
2
8
7
6
14 13 12 11
Pin
No.
1
2
3
4
5
Signal
Red video
Green video
Blue video
Ground
NC*
Pin
No.
6
7
8
9
10
Signal
Red video ground
Green video ground
Blue video ground
NC*
Ground
Pin
Signal
No.
11
Ground
12
Data (SDA)
13
H. Sync
14
V. Sync
15
Clock (SCL)
(*NC: No Connection)
DVI-D Connector
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
17 18 19 20 21 22 23 24
Pin
No.
1
2
3
4
5
6
7
8
Signal
TMDS Data2TMDS Data2+
TMDS Data2/4
Shield
NC*
NC*
DDC Clock (SCL)
DDC Data (SDA)
NC*
Pin
No.
9
10
11
12
13
14
15
16
Signal
TMDS Data1TMDS Data1+
TMDS Data1/3
Shield
NC*
NC*
+5V Power
Ground (For +5V)
Hot Plug Detect
Pin
No.
17
18
19
20
21
22
23
24
Signal
TMDS Data0TMDS Data0+
TMDS Data0/5
Shield
NC*
NC*
TMDS Clock shield
TMDS Clock+
TMDS Clock(*NC: No Connection)
USB Port
Upstream
No.
1
2
3
4
Signal
VCC
- Data
+ Data
Ground
Signal
Cable power
Serial data
Serial data
Cable Ground
Series B
7. SPECIFICATIONS
33
English
8. GLOSSARY
Clock
With the analog input signal display, the analog signal is converted to a digital signal
by the LCD circuitry. To convert the signal correctly, the LCD monitor needs to
produce the same number clock pulse as the dot clock of the graphics system. When
the clock pulse is not correctly set, some vertical bars of distortion are displayed on
the screen.
Color Temperature (Temperature)
Color Temperature is a method to measure the white color tone, generally indicated
in degrees Kelvin. At high temperatures the white tone appears somewhat blue, while
at lower temperatures it appears somewhat red. Computer monitors generally give
best performance at high temperature settings.
5000 K: Slightly reddish white.
6500 K: White called daylight color.
9300 K: Slightly bluish white.
DVI (Digital Visual Interface)
A digital flat panel interface. DVI can transmit digital data from the PC directly
without loss with the signal transition method “TMDS”.
There are two kinds of DVI connectors. One is DVI-D connector for digital signal
input only. The other is DVI-I connector for both digital and analog signal inputs.
Gain
Adjusts each color parameter for red, green and blue. The color of the LCD monitor
is displayed through the color filter of the LCD panel. Red, green and blue are the
three primary colors. The colors on the monitor are displayed by combining these
three colors. The color tone can change by adjusting the illumination amount passed
through each color’s filter.
Gamma
Generally, the relationship that the light intensity values of a monitor change
nonlinearly to the input signal level is called “Gamma Characteristic”. On the
monitor, low gamma values display the whitish images and high gamma values
display the high contrast images.
Phase
The phase adjustment decides the sampling timing point for converting the analog
input signal to a digital signal. Adjusting the phase after the clock adjustment will
produce a clear screen.
Range Adjustment
The Range Adjustment controls the level of output signal range to display the whole
color gradation.
34
8. GLOSSARY
English
Resolution
The LCD panel consists of a fixed number of pixel elements which are illuminated to
form the screen image. The display panel of this monitor consists of 1280 horizontal
pixels and 1024 vertical pixels. At a resolution of 1280 x 1024, images are displayed
as a full screen (1:1).
sRGB (Standard RGB)
“International Standard for Red, Green, and Blue color space”
A color space was defined with the aim of the color matching between applications
and hardware devices, such as monitors, scanners, printers and digital cameras. As a
standard default space, sRGB allows Internet users to closely match colors.
TMDS (Transition Minimized Differential Signaling)
A signal transition method for the digital interface.
8. GLOSSARY
35
APPENDIX/ANHANG/ANNEXE
Preset Timing Chart for Analog input
Timing-Übersichten für Analog Eingang
Synchronisation des Signaux pour Analog numerique
Based on the signal diagram shown below factory presets have been registered in the
monitor's microprocessor.
Der integrierte Mikroprozessor des Monitors unterstützt werkseitige
Standardeinstellungen (siehe hierzu die nachfolgenden Diagramme).
Signaux ont été enregistrés en usine dans le microprocesseur du moniteur, conformément
au diagramme de synchronisation ci-dessous.
Mode
i
Dot Clock
MHz
Sync Polarity
H
V
Frequencies
H kHz
V Hz
VGA Graphics
320 x 200
25.2
Nega.
Nega.
31.47
70.09
VGA
640 x 480
25.2
Nega.
Nega.
31.47
59.94
VGA TEXT
720 x 400
28.3
Nega.
Posi.
31.47
70.09
VESA
640 x 480
31.5
Nega.
Nega.
37.86
72.81
VESA
640 x 480
31.5
Nega.
Nega.
37.50
75.00
VESA
800 x 600
36.0
Posi.
Posi.
35.16
56.25
VESA
800 x 600
40.0
Posi.
Posi.
37.88
60.32
VESA
800 x 600
50.0
Posi.
Posi.
48.08
72.19
VESA
800 x 600
49.5
Posi.
Posi.
46.88
75.00
VESA
1024 x 768
65.0
Nega.
Nega.
48.36
60.00
VESA
1024 x 768
75.0
Nega.
Nega.
56.48
70.07
VESA
1024 x 768
78.8
Posi.
Posi.
60.02
75.03
VESA
1152 x 864
108.0
Posi.
Posi.
67.50
75.00
VESA
1280 x 960
108.0
Posi.
Posi.
60.00
60.00
VESA
1280 x 1024
108.0
Posi.
Posi.
63.98
60.02
VESA
1280 x 1024
135.0
Posi.
Posi.
79.98
75.03
APPENDIX/ANHANG/ANNEXE
EMC Information
Essential performance of FlexScan L560T-CB is to display images and operate functions normally.
CAUTION
The FlexScan L560T-CB requires special precautions regarding EMC and need to be installed, put
into service and used according to the following information.
Do not use any cables other than the cables that provided or specified by us.
Using other cables may cause the increase of emission or decrease of immunity.
Do not put any portable and mobile RF communications equipment close to the FlexScan L560TCB. Doing so may affect the FlexScan L560T-CB.
The FlexScan L560T-CB should not be used adjacent to or stacked with other equipment. If
adjacent or stacked use is necessary, the equipment or system should be observed to verify
normal operation in the configuration in which it will be used.
Guidance and manufacturer’s declaration - electromagnetic emissions
The FlexScan L560T-CB is intended for use in the electromagnetic environment specified below.
The customer or the user of the FlexScan L560T-CB should assure that it is used in such an environment.
Emission test
Compliance
Electromagnetic environment - guidance
RF emissions
EN55011
Group 1
The FlexScan L560T-CB uses RF energy only for its internal
function.
Therefore, its RF emission are very low and are not likely to cause
any interference in nearby electronic equipment.
The FlexScan L560T-CB is suitable for use in all establishments,
including domestic establishments and those directly connected
to the public low-voltage power supply network that supplies
buildings used for domestic purposes.
RF emissions
Class B
EN55011
Harmonic emissions Not applicable
EN61000-3-2
Voltage fluctuations / Complies
flicker emissions
EN61000-3-3
Guidance and manufacturer’s declaration - electromagnetic immunity
The FlexScan L560T-CB is intended for use in the electromagnetic environment specified below.
The customer or the user of the FlexScan L560T-CB should assure that it is used in such an environment.
Immunity test
IEC60601 test level
Compliance level
Electrostatic
discharge (ESD)
EN61000-4-2
±6kV contact
±8kV air
±6kV contact
±8kV air
Electromagnetic environment guidance
Floors should be wood, concrete or
ceramic tile. If floors are covered
with synthetic material, the relative
humidity should be at least 30%.
Electrical fast
±2kV
±2kV
Mains power quality should be
transient / burst
for power supply lines for power supply lines that of a typical commercial or
EN61000-4-4
±1kV
±1kV
hospital environment.
for input/output lines
for input/output lines
Surge
±1kV line(s) to line(s) ±1kV line(s) to line(s) Mains power quality should be
EN61000-4-5
±2kV line(s) to earth
±2kV line(s) to earth that of a typical commercial or
hospital environment.
Voltage dips, short
<5% UT (>95% dip in <5% UT (>95% dip in Mains power quality should be
UT) for 0.5 cycle
UT) for 0.5 cycle
that of a typical commercial or
interruptions and
40% UT (60% dip in hospital environment. If the user
voltage variations on 40% UT (60% dip in
UT) for 5 cycles
of the FlexScan L560T-CB requires
power supply input UT) for 5 cycles
70% UT (30% dip in
70% UT (30% dip in continued operation during
lines
UT) for 25 cycles
UT) for 25 cycles
power mains interruptions, it is
EN61000-4-11
<5% UT (>95% dip in <5% UT (>95% dip in recommended that the FlexScan
UT) for 5sec
UT) for 5sec
L560T-CB be powered from an
uninterruptible power supply or a
battery.
Power frequency
3A/m
3A/m
Power frequency magnetic fields
(50/60Hz)
should be at levels characteristic
magnetic field
of a typical location in a
EN61000-4-8
typical commercial or hospital
environment.
NOTE UT is the a.c. mains voltage prior to application of the test level.
Guidance and manufacturer’s declaration - electromagnetic immunity
The FlexScan L560T-CB is intended for use in the electromagnetic environment specified below. The
customer or the user of the FlexScan L560T-CB should assure that it is used in such an environment.
Immunity test
IEC60601 test level
Compliance level
Electromagnetic environment guidance
Conducted RF
EN61000-4-6
3Vrms
150kHz to 80MHz
3V
Radiated RF
EN61000-4-3
3V/m
80MHz to 2.5GHz
3V/m
Portable and mobile RF
communications equipment should
be used no closer to any part of
the FlexScan L560T-CB, including
cables, than the recommended
separation distance calculated from
the equation applicable to the
frequency of the transmitter.
Recommended Separation distance
d = 1.2 √P
d = 1.2 √P, 80MHz to 800MHz
d = 2.3 √P, 800MHz to 2.5GHz
Where “P” is the maximum output
power rating of the transmitter
in watts (W) according to the
transmitter manufacturer and “d”
is the recommended separation
distance in meters (m).
Field strengths from fixed RF
transmitters, as determined by an
electromagnetic site surveya, should
be less than the compliance level in
each frequency rangeb.
Interference may occur in the
vicinity of equipment marked with
the following symbol.
NOTE 1 At 80 MHz and 800 MHz, the higher frequency range applies.
NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by
absorption and reflection from structures, objects and people.
a
Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and
land mobile radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted
theoretically with accuracy. To assess the electromagnetic environment due to fixed RF transmitters, an
electromagnetic site survey should be considered. If the measured field strength in the location in which
the FlexScan L560T-CB is used exceeds the applicable RF compliance level above, the FlexScan L560TCB should be observed to verify normal operation. If abnormal performance is observed, additional
measures may be necessary, such as reorienting or relocating the FlexScan L560T-CB.
b
Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 3 V/m.
Recommended separation distances between portable and mobile RF communications
equipment and the FlexScan L560T-CB
The FlexScan L560T-CB is intended for use in an electromagnetic environment in which radiated RF
disturbances are controlled. The customer or the user of the FlexScan L560T-CB can help prevent
electromagnetic interference by maintaining a minimum distance between portable and mobile RF
communications equipment (transmitters) and the FlexScan L560T-CB as recommended below, according
to the maximum output power of the communications equipment.
Rated maximum output
Separation distance according to frequency of transmitter
power of transmitter
m
150kHz to 80MHz
80MHz to 800MHz
800MHz to 2.5GHz
W
d = 1.2 √P
d = 1.2 √P
d = 2.3 √P
0.01
0.12
0.12
0.23
0.1
0.38
0.38
0.73
1
1.2
1.2
2.3
10
3.8
3.8
7.3
100
12
12
23
For transmitters rated at a maximum output power not listed above, the recommended separation distance
“d” in meters (m) can be estimated using the equation applicable to the frequency of the transmitter, where
“P” is the maximum output power rating of the transmitter in watts (W) according to the transmitter
manufacturer.
NOTE 1 At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.
NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by
absorption and reflection from structures, objects and people.
Cable length
Power Cord :
Signal Cable (MD-C87) :
USB Cable (MD-C93) :
Signal Cable (FD-C39) :
Accessary
Accessary
Accessary
Option
2.0m
1.8m
1.8m
2.0m
153 Shimokashiwano, Hakusan, Ishikawa 924-8566 Japan
Phone: +81 76 277 6792 Fax: +81 76 277 6793
中国苏州市苏州工业园区展业路8号中新科技工业坊5B
Phone: +86 512 6252 0100 Fax: +86 512 6252 1508
Siemensallee 84, 76187 Karlsruhe, Germany
Phone: +49 721 20321 0 Fax: +49 721 20321 471
http://www.eizo.com
Copyright © 2009-2013 EIZO Corporation All rights reserved.
5th Edition-October 2013 Printed in Japan.
00N0L507E1
(U.M-L560T-CB-EU)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising