kingston-hyperx-fury-red-ddr3-1866-8-gb-kit-hx318c10frk2 8

kingston-hyperx-fury-red-ddr3-1866-8-gb-kit-hx318c10frk2 8
HX318C10FRK2/8
8GB (4GB 512M x 64-Bit x 2 pcs.)
DDR3-1866 CL10 240-Pin DIMM Kit
SPECIFICATIONS
CL(IDD)
10 cycles
Row Cycle Time (tRCmin)
44.75ns (min.)
Refresh to Active/Refresh
Command Time (tRFCmin)
260ns (min.)
Row Active Time (tRASmin)
32.125ns (min.)
Maximum Operating Power
TBD W* (per module)
UL Rating
94 V - 0
Operating Temperature
0o C to 85o C
Storage Temperature
-55o C to +100o C
*Power will vary depending on the SDRAM used.
DESCRIPTION
FEATURES
HyperX HX318C10FRK2/8 is a kit of two 512M x 64-bit (4GB)
DDR3-1866 CL10 SDRAM (Synchronous DRAM) 1Rx8 memory
•
JEDEC standard 1.5V (1.425V ~1.575V) Power Supply
•
VDDQ = 1.5V (1.425V ~ 1.575V)
modules, based on eight 512M x 8-bit DDR3 FBGA components
per module. Total kit capacity is 8GB. Each module kit has
•
933MHz fCK for 1866Mb/sec/pin
been tested to run at DDR3-1866 at a low latency timing of
10-11-10 at 1.5V. Additional timing parameters are shown in
•
8 independent internal bank
the PnP Timing Parameters section below. The JEDEC standard electrical and mechanical specifications are as follows:
•
Programmable CAS Latency: 13, 11, 10, 9, 8, 7, 6
•
Programmable Additive Latency: 0, CL - 2, or CL - 1 clock
•
8-bit pre-fetch
•
Burst Length: 8 (Interleave without any limit, sequential with
starting address “000” only), 4 with tCCD = 4 which does not
allow seamless read or write [either on the fly using A12 or
MRS]
•
Bi-directional Differential Data Strobe
•
Internal(self) calibration : Internal self calibration through ZQ
pin (RZQ : 240 ohm ± 1%)
•
On Die Termination using ODT pin
•
Average Refresh Period 7.8us at lower than TCASE 85°C,
3.9us at 85°C < TCASE < 95°C
•
Asynchronous Reset
•
PCB : Height 1.180” (30.00mm), single sided component
Note: The PnP feature offers a range of speed and timing options to support
the widest variety of processors and chipsets. Your maximum speed will
be determined by your BIOS.
PnP JEDEC TIMING PARAMETERS:
•
•
•
DDR3-1866 CL10-11-10 @1.5V
DDR3-1600 CL9-10-9 @1.5V
DDR3-1333 CL8-9-8 @1.5V
Continued >>
kingston.com/hyperx
Document No. 4807031-001.A00
03/11/14
Page 1
continued
HyperX
MODULE DIMENSIONS
MODULE WITH HEAT SPREADER
FOR MORE INFORMATION, GO TO WWW.KINGSTON.COM/HYPERX
All Kingston products are tested to meet our published specifications. Some motherboards or system configurations may not operate at
the published HyperX memory speeds and timing settings. Kingston does not recommend that any user attempt to run their computers
faster than the published speed. Overclocking or modifying your system timing may result in damage to computer components.
kingston.com/hyperx
Document No. 4807031-001.A00
Page 2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising