Mitsubishi Electric PAC-SE51CRA Installation Manual Eng

Mitsubishi Electric PAC-SE51CRA Installation Manual Eng
MITSUBISHI ELECTRIC
Building Air-Conditioning Control System
Remote Controller
PAC-SE51 CRA
lnstallation Manual
This manual contains only the lnstallation procedure for the remote controller. For informatlon about how to wlre and lnstall alr conditionlng
units, see their installatlon manua;,;.ls,,_.~~~~----~
For your safety, thoroughly read (11 Safety Precautlons) descrlbed below before lnstalllng the remote controller correctly.
( 1
•
1 Safety Precautions )
The following two symbols are used to denote dangers that may
&WARNING
&CAUTION
•
Ье
caused
Ьу
lncorrect use:
Thls symbol denotes what could lead to serlous lnjury or death lf the remote controller is mlsused.
This symbol denotes what could lead to personal lnjury or property damage lf the remote controller ls mlsused.
After reading thls lnstallation manual, keep it in а safe place where the user can refer to lt whenever necessary.
Make sure that thls manual ls forwarded to the next user.
&WARNING
Aak your dealer or technlcal repreaentatlve to lnatall the unlt.
Any deflclency caused Ьу your own lnstallatlon may result ln an electrlc
shock or flre.
Enaure that lnatallatlon work la done correctly followlng thla lnatallatlon manual.
Any deflclency caused Ьу lnstallatlon may result ln an electrlc shock or flre.
lnatall ln а place whlch la atrong enough to wlthatand the welght of
the PAC-SE51CRA.
Any lack of strength may cause the PAC-SE51 CRA to fall down, resultlng
ln personal lnjury.
АН
Flrmly connect the wlrlng ualng the apeclfled саЫеа. Carefully check
that the саЫеа do not exert any force оп the termlnala.
lmproper wlrlng connectlons may produce heat and posslЫy а flre.
Do not move and re-lnatall the PAC-SE51 CRA youraelf.
Any deflclency caused Ьу lnstallatlon may result ln an electrlc shock or flre.
Ask your dlstrlbutor or speclal vendor for movlng and lnstallatlon.
electrlcal work muat Ье performed Ьу а Jlcenaed technlclan, accordlng to local regulatlona and tha lnatructlona glven ln thla manual.
Any lack of electrlc clrcult or any deflclency cauaed Ьу lnstallatlon may result ln an electrlc shock or flre.
Never modlfy or repalr the PAC-SE51CRA Ьу youraelf.
Any deflclency caused Ьу your modlflcatlon or repalr may result ln an electrlc shock or tlre.
Consult wlth your dealer about repalrs.
&CAUTION
Do not lnatall ln any place expoaed to flammaЫe gaa leakage.
Flammable gases accumulated around the body of PAO-SE51CRA may
cause an exploslon.
Do not lnatall ln any ateamy place auch а bathroom or kltchen.
Avold any place where molsture ls condensed lnto dew. Dolng so may cause
an electrlc shock or а malfunctlon.
Do not uae ln any apeclal envlronment.
Uslng ln any place exposed to oll (lncludlng machlne oll), steam and sulfurlc gas may deterlorate the performance slgnlflcantly or glve damage to the
component parts.
Do not lnatall ln any place where acldlc or alkallne aolutlon or apeclal
apray are often uaed.
Dolng so may cause an electrlc shock or malfunctlon.
Wlre ао that lt doea not recelve any tenalon.
Tenslon may cause wlre breakage, heatlng or flre.
А
Uae atandard wlre• ln compllanoe wlth the current capaclty.
fallure to thls may result ln an electrlc leakaga. heatlng or flre.
Do not touch any РСВ (Prlnted Clrcult Board) wlth your handa or wlth
toola. Do not allow duat to collect on the РСВ.
Dolng so may cause flre or an electrlc shock.
Completely aeal the wlre lead-ln port wlth putty etc.
Any dew, molsture. cockroaches, lnsects enterlng the unlt may cause an
electrlc shock or а maltunctlon.
Do not waah wlth water.
Dolng so may cause an .electrlc shock or
Do not touch any control button wlth your wat handa.
Dolng so may cause an electrlc shock or а malfunctlon.
а
malfunctlon.
Do not preaa any control button ualng а aharp objact.
Dolng so may cause an electrlc shock or а maltunctlon.
Do not lnatall ln any place at а temperature of more than 40"С or leaa
than О С or axpoeed to dlrect aunllght.
0
Never contact the powar aupply wlth the control wlrlng termlnala.
Dolng so wlll certalnly cause the controller to catch flre.
(2
Specification )
Source power requlrement
DC17 V - DСЗО V, 0.02 А
Power recelved from outdoor unlt via M-NET transmlsslon llne.
M-NET transmlsslon line ; DСЗО V+AMI slgnal (DC±S V)
lnput voltage
lnterface condition for transmission line
Number of M-NET controlled indoor
unlt controlled Ьу PAC-SE51 САА
Envlronmental condition
Temperature
Dlmenslons
Weiaht
Humlditv
120 (Hloh)
О.15 ka
(з
1 - 16
х
о - 40°С
Operating
Non operatlng
о - 70°С
1 30 - 90%RH (No condensation)
70 (Width) х 8<41> (Depth) mm
1
Checklng the Supplied Parts )
Check that the
Ьох
lncludes the followlng parts ln addltlon to thls lnstallatlon manual:
Enclosed Parts
Remote Controller Model Name
PAC-SE51CRA
NOTE:
(1)
The parts llsted below must Ье purchased separately.
СаЫе
connectlng the remote controller to the lndoor unlt:
Use the саЫе speclfled below.
1СаЫе tvpe 1 VCTF or CW (2-core): 0.75 *
(1) Remote controller .........•.. " ............ "" ........................................ " ................ " ................................. 1
(2) Cross-recessed pan-head screws ........... " ................................................ " .................. " .. " ........... 2
(З) Operatlon manual ..... " ...........................•.............. " ... " " ..•.•......•.................. ". .... .. . ... ...... .. ..... .. .. . .. .. 1
1.25 mm• or equlvalent
1
CVV ls а control саЫе whlch is sheathed ln polyvlnyl chlorlde wlth polyvlnyl insulated wires inslde.
NOTE:
lf you need to use а саЫе extension longer than 1 О
meters, select an electrlc wire that meets the followlng speclflcations:
Wire specification ..... VCTF or CVV (2-core):
1 .25 mm 2 or equlvalent
(2)
(4
The swltch
Ьох
ls
for
mouпtlпg.
Use the swltch
Ьох
speclfled
the right.
Ьох.
lпstall
the swltch
explalпed below.
Swltch
Ьох
(purchased separately) as
Outllneofremo~W
NOTE:
•
•
•
,
L _ ,
-
40mmormore
Purchase the
thlп-copper wlrlпg
plpe
Ве
sure to
lпstal/
Ьох
the switch
with the clearaпce showп lп the
the space betweeп the uпit апd апу
lllustratioп at the left. (Check
projectloп such as а stud.)
Projectlng
object such as
astud
Ьох ~гФ=-11
controller
(2)
iп
lnstalling the Remote Controller )
1. Mount the swltch
(1)
пecessary
апd lockпuts апd bushlпgs
Leave а space of 120 mm or more below the remote coпtroller so
that the screwdrlver сап Ье used.
Slnce the remote coпtroller ls equipped wlth а temperature seп­
sor, lпstall the remote coпtroller lп а locatloп where the average
room temperature сап Ье detected апd whlch ls поt directly affected Ьу some heat source, dlrect suпllght or alr Ыоwп from ап
alr coпdltloпer.
separately.
2. lnatall thf!t remote controller.
(1)
(2)
Pull out about 80 mm of саЫе from the wall апd remove the lnsulatioп from its епd.
Use putty to seal the саЫе lead-lп hole lп order to preveпt lпsects from damagiпg the wirlпg апd to preveпt alr from
remote coпtroller circult board. lf the hole ls поt sealed well, the remote coпtroller clrcult Ьoard may Ье damaged.
11
Leadlng
wlre
(З)
Соппесt
the
саЫе
to the
....
lnsulatlon
termlпal
Sheath
board
iп
the bottom rear of the remote
The
~--- ~ =.":. . .
~ саЫе.
саЫе
does
поt
coпtroller uпit.
have polarity.
Wheп соппесtlпg straпded саЫе,
iпsertlпg
The
the
hold
dowп
the
buttoп оп
the
termlпal
board whlle
саЫе.
саЫе соппесts
to the
malп termlпal
board
wheп
it ls
lпserted lпto
the bottom
termlпal.
Wheп discoппectiпg the саЫе, hold dowп the buttoп whlle pulllпg out the саЫе.
Atter lпsertiпg the саЫе, sllghtly tug on it to check that lt does поt easlly dlscoппect.
lf the саЫе ls поt securely соппесtеd, а short-circult or malfuпctloп may occur.
lnsertthe
(4)
the
10
1
1
coпdeпslпg оп
Remove the remote coпtroller cover uslпg а staпdard screwdrlver, theп attach the remote coпtroller uпlt to the swltch Ьох usiпg the two
cross-recessed paп-head screws. Use а staпdard screwdrlver wlth а Ыаdе that is 4 mm or wlder to remove the _cover.
eпclosed
Remote controller cover
iЪCAUTION:
•
•
(5)
Set the remote
Forclпg off the cover uslпg а screwdrlver that ls less thaп 4 mm wlde may result lп damage to the equlpmeпt
or lпjurles.
Attach the remote coпtroller to а level surface. Do поt overtlghteп the screws, otherwlse the case may become deformed or break.
coпtroller
address.
SW1
SW2
[й] ~
Rotary awltchea
Set the remote coпtroller address
the front of the remote coпtroller.
•
uslпg
the rotary swltches SW1
апd
SW2
оп
Settlпg raпge:
1 01 to 200
Rotary switch SW1 lпdlcates the teпs dlglt апd SW2 lпdlcates the опеs diglt.
lп addltlon. 100 is automatlcally added to the settlng as shown below.
Rotary swltch settlng
Remote controller address
The address ls set to 01
wheп
00
200
01 - 99
101 - 199
the remote
coпtroller
ls shlpped from the
maпufacturer.
iЪCAUTION:
(6)
The address must Ье set lf the remote coпtroller ls used as а part of а multluпit system. Set the address accordlпg to lts posltloп iп the system. lп addltion, refer to the air coпdltioпer lпstallatioп Maпual formore lпformatioп
coпcemlпg the settlng of the addresses.
Atter settlпg the remote controller address, attach the remote controller cover.
attachlng the remote controller cover, set the top of the cover опtо the two top hooks, then push ln on the bottom of the cover untll
lt snaps into place.
lf the bottom of the cover ls attached first, the top of the cover cannot be.attached. Forcefully pushlng ln the top of the cover to attach
lt may break the hooks.
Wheп
iЪCAUTION:
(7)
•
•
Press ln оп the bottom of the cover uпtll it sпaps lnto place.
When attachiпg the remote controller cover, Ье careful not to move
the room temperature sensor out of place. Movlng the seпsor out of
place or plпching lt whlle attachlng the cover may result ln the seпsor
malfunctionlng or belng damaged.
·
1IW
Aoom'8mpe'8ture
sensor
1О.11О.1
c:::J
о
When the lndoor unlt must Ье registered wlth the remote controller ln а group arrangement or а system where
used, refer to(5\ Reglsterlng the indoor Onlt Wlth the Remote Controller).
dlffereпt
refrigerants are
(5
Reglstering the lndoor Unlt Wlth the Remote Controller )
(lnltlal reglstratlon mode operatlon)
Ап lпdoor uпit
Ье reglstered wlth the remote coпtroller lп а group arraпgemeпt or а system where dlffereпt refrlgeraпts are used. Reglster
the lпltlal reglstratloп mode as showп below. lп addltioп, the lпltlal reg/stratloп mode сап Ье used to search for ап lпdoor unlt
reglstered to the group or to delete а reglstratloп.
Thls remote coпtroller саппоt Ье used to perform ап lпterlocklпg reglstratloп of lпterlocked uпlts. The ceпtral coпtroller (MJ-103MTRA) or
пetwork remote coпtroller (PAR-F25MA) must Ье used to make lпterlocklпg reglstratloпs.
must
ап lпdoor uпlt us/пg
Settlng Procedure
Q)
®
Turп
off the uпlt.
(Perform the followlпg
operatloп
after "НО" flashes
оп
the dlsplay.)
Hold dowп both ТЕМР. Ci::> апd СУ::> for more thaп 2 secoпds.
Thls starts the lпitlal registratloп mode апd the set remote coпtrol­
ler address flashes оп the dlsplay.
1 / /
- ' '/П
/
_. IU ~'""==~------­
/
®
/ \
Press ТЕМР. ~ to select the address of the lпdoor uпlt
that you wlsh to register wlth thls remote coпtroller.
After the butloп is pressed опсе, the remote coпtroller address, апd theп the lпdoor uпit address ls dlsplayed. Afterwards, each press of the butlon lпcreases the lпdoor unlt
address Ьу 1 as showп below. Holdlпg down the buttoп
chaпges the address more qulckly.
[101) -+ [- - -]
-+
[001]
[002) -+
-+
-+
[049]
-+
[050]
Conflrmatlon of reglstered address
®
Address delectlon
(Set remote controller address)
(j)
Flashes
@
Dlsplay the addresses of the lпdoor uпlts that are reglstered
wlth thls remote controller.
Each press of ТЕМР. СУ::> lп step ® or @ dlsplays the address of а reglstered Jndoor unlt апd lts type, "IC".
lf no lndoor uпlt ls reglstered, "- - -" appears ln the address
dlsplay апd по type ls dlsplayed.
Wheп
the address of the iпdoor uпlt that you wlsh to reglster
ls dlsplayed, press ~ to beglп reglsterlпg.
lf the reglstratloп ls completed correctly, the dlsplay appears
as showп below.
Delete the address of ап lndoor unlt reglstered wlth thls remote controller.
Hold down [ON/OFF] twlce for 2 seconds each tlme elther ln
step @ or after the reglstratlon ls complete to delete the registratloп of the lndoor unlt that ls curreпtly dlsp/ayed.
пп
ии
IГ
пп
ии
The lndoor unlt type, "IC",
ls dlsplayei:t.
IL
When the dlsplay appears as showп above, hold down [ON/
OFF] twlce for 2 secoпds each tlme.
lf the reglstratloп ls not completed correctly, "88" flashes ln
the dlsplay. Check that the selected lndoor unlt address or
the wirlng are correct.
Up to 16 lndoor uпlts can Ье reglstered.
®
/
1
J,
[ ии
nn. //
After reglsterlng, hold dowп both ТЕМР. ~ and СУ::> for
more thaп 2 secoпds to епd the lnltial reglstratlon mode and
the normal dlsplay appears.
lf the reglstratlon ls deleted correctly, "- - " appears lп the
dlsplay.
lf the reglstratlon ls not deleted correctly, "88" flashes in the
dlsplay. Check that the selected lndoor unlt address and the
wlring are correct.
NOTE:
( 6
•
•
Up to 16 lndoor uпlts сап Ье reglstered.
lf the reglstratloп cannot Ье completed or deleted correctly, elther the set address or the wlrlng of the lndoor unlt whose
reglstratlon you wlsh to add or delete may Ье lncorrect. Check the wlrlng and the address that ls set.
Operatlng Durlng the Test Run )
1.
2.
How to Use the Test Run
The test run свпnоt Ье started uslng thls remote controller. Use the network or group remote controller to start the test run. During
run, thls remote controller appears as shown below. After two hours, the test run stops automat/cally.
Press [ON/OFF] durlng the test run to
speed сап Ье adJusted.
сапсеl
lt and turn off the
uпlt.
The room temperature cannot
Ье
set
durlпg а
test
ruп;
а
test
only the alr
lndoor unlt address of the dlsolaved оlов temoerature
The address of the lndoor unlt reglsterad wlth thls remote controller ls dlsplayed. lf
more than one lndoor unlt ls reglstered, the addresses of the other unlts oan Ье dlsplayed Ьу presslng ТЕМР. ~- Dlsplay range: 001 to 050
DJ
1
1
Q
0
,._-'
C'·S
-"
/
·~·
-
~п
Т
си·с
lndoor unlt plpe temperature
The plpe temperature of the lndoor unlt address shown ls dlsplayed.
Dlsplay range: -99°С to 99°с
lf the temperature exceeds thls range, "-99°С" or "99°С" f\ashes on the dlsplay.
@
Remalnlng tlme of the test run
The amount of tlme remalnlng for the test run ls dlsplayed.
Dlsplay range: 2:00 to 0:01
Thls product ls deslgned and lnteпded for use ln а resldentlal, commerclal or llght-lndustrlal envlronment.
The product at hand ls based on the follow/ng EU regulatlons:
Low Voltage Defectlve 73/23/ЕЕС
Electromagпetlc Compatlbllity Dlrectlve 89/336/ЕЕС
~ MITSUBISHI ELECTRIC CORPORATION
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising