SPU16D SERIES 15W Desk Top Switching Power Supplies For I.T.E. Description: The SPU16D series of AC/DC switching mode power supplies provide 15 Watts of continuous output power. All supplies are UL 94V-1 min compliant. All models meet FCC Part-15 class B and CISPR-22 class B emission Limits and are designed to comply with UL/c-UL(UL 60950-1:2ndEdition), TUV/GS (EN 60950-1:2ndEdition) and new CE requirements. All units are 100% burned in and tested. Features: Wide Operating Voltage 90 to 264 VAC,47 to 63 Hz A Stand And Mains AC Power Cord Optional Output Connector (See appendix) Single Output Energy Star 2.0, Efficiency level V Class II 2 year warranty Safety Approvals: CB Agree to apply for the PSE if order on hand Electrical Characteristics: Sym. Vin fin Parameter Operate Voltage Range Input Frequency Output Power Range Io Output Current Range Vo Output Voltage Range Iil Input Current (Low Line) Iih Input Current (High Line) Irl Low Line Inrush Current Irh High Line Inrush Current Eff Efficiency REG-i Line Regulation REG-o Load Regulation OVP OCP Ttr Over Voltage Protection Over Current Protection Time of Transient Response Thold Hold-Up Time Ts * Vp-p Ilk TC Test Conditions Safety Approvals Input Voltage Range Po Start Up Time Sym. Unit 100 240 VAC 90 264 VAC 15 W See rating chart 0.4 Io=Full load, Vin=230VAC 0.26 Io=Full load, 25°c, Cool start, Vin=115VAC Io=Full load, 25°c, Cool start, Vin=230VAC Io=Full Load, Vin=230VAC Io=Full Load Vin=230VAC All output T e s t Conditions Operating Temperature Storage Temperature Operating Humidity Storage Humidity Operating Temperature at 25 C, Calculated per MIL-HDBK-217F Derate linearly from 100% load at 40 C to 50% load at 70 C A A 26 30 A 85 % 0.5 1 % 3 10 % Io=Full Load to Half Load, Vin=100VAC 4 8 0.3 A A Nil.But,Output protected to short circut conditions Io=Full Load, Vin=100VAC V 15 Nil Io=Full Load, Vin=110VAC Hz 12 72 % % ms ms 1 2 S 0.5 1 % 0.5 0.75 mA 0.04 % /°C Min. Typ. Max. Unit Safety Ground Leakage Current Io=Full Load, Vin=240VAC Parameter 63 See rating chart Io=Full load, Vin=115VAC * Note: The Ripple & Noise which is under 3.3VCD at 2% max Environmental : Toper Tstg Ho Hr MTBF Pd Min. Typ. Max. 47 Vin=90 to 264VAC Ripple & Noise (Peak to Peak) Full Load, Vin=90VAC Temperature Coefficient S&E -0.04 0 -40 0 0 0.1M 40 70 85 95 75 C C % % Hrs SPU16D SERIES 15W Desk Top Switching Power Supplies For I.T.E. Safety Specifications: Sym. Vps Ris Parameter Dielectric Withstanding Voltage for Primary to secondary Isolation Resistance CISPR EMI requirements for CISPR-22 FCC EMI requirements for FCC PART-15 Min. Typ. Max. Unit Primary to secondary 4242 VDC Test Voltage=500VDC 50 Vin=220VAC B CLASS Vin=110VAC B CLASS T e s t Conditions M Output Voltage And Current Rating Chart ( Single Output ) : Model Number Output Voltage SPU16D-101 03 ~ 05 VDC SPU16D-103 06 ~ 08 VDC SPU16D-102 SPU16D-104 SPU16D-105 SPU16D-106 SPU16D-107 SPU16D-108 SPU16D-109 SPU16D-110 SPU16D-111 Output Current 2.50 A max Total Regulation 7% Maximum Outpu t Power 12W 05 ~ 06 VDC 2.50 ~ 2.00 A 5% 12W 08 ~ 11 VDC 1.87 ~ 1.36 A 5% 15W 11 ~ 13 VDC 13 ~ 16 VDC 16 ~ 21 VDC 21 ~ 27 VDC 27 ~ 33 VDC 33 ~ 40 VDC 40 ~ 48 VDC 2.00 ~ 1.50 A 1.36 ~ 1.15 A 1.15 ~ 0.94 A 0.94 ~ 0.72 A 0.72 ~ 0.55 A 0.55 ~ 0.45 A 0.45 ~ 0.37 A 0.37 ~ 0.31 A 5% 5% 5% 5% 5% 5% 3% 3% 12W 15W 15W 15W 15W 15W 15W 15W The output voltage under 15V had been approved by TUV/PSE. SPU16D-101 had been approved by CEC level IV. SPU16D-102~111 had been approved by CEC level V. Mechanical Specifications : Note: 1. Dimensions are shown in mm. 2. Weight: 165gs approx. (Unincluded an input cord) 3. Optional output connector: See Page Appendix.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project