FOUR

CHANNEL

WIRELESS

RECEIVER

Manual

of

four

channel wireless receiver

Thank you for selecting this kind of n,ireless monitor receiver, in order to help you use the product better, please read the manual carefulll.

I.

Basic

specification

:

Receiving frequency

:

2.4l4GIJz. 2.432GH2.

2.450GH2. 2.468GH2.

Video output: 75QlIVp-p

Audio output: l0KQ/200mVp-p

Signal output: Can output two channels with the same audio and viedo signal

PowerAdapter: DC 12Vl500mA

Power consumption: < 2W

Remote control distance: 6- 8M

Working temperature: -10 - 50oC

Volume: 120 X 99 X 3()mm

Weight: l50g

II.

Diagram:

Channel key(on/off)

CH+

CH-

Power

Video 2

2 vid eo I

III.

Instructions

of the

function

and

operation:

1. Put the camera in the place where need to monitor.

2.

Insert the input end of the power adapter

in

the AC normal voltage socketl insert the DC output plug of power adapter in the power input jack of the camera.

3. The distance between the cameras, the camera between the receiver should be kept about or over 2 meters, other-wise receiving will be interfered.

4. Use theAV cable to connect one channel

of

audio and videooutput ofthe receiverwith the audioand video input plugs

of

the.TV set or monitor.

5. Connect the DC 12Vl500mApower adapter

with

the receiver and

put

through the circuit, the channel display window will show red

light

point.

6. Press the off/on key ofthe remote controller, or press the channel key of the receiver and open the power adapter of the receiver. The receiver will acquiesce the channel

I

after opening.

7. Press the channel key of remote controller(Number 1,

2r 3,4) in order to make the camera and receiver on the same channel,or press the channel key ofthe receiver in order to make the channel on the blue display window of receiver the same as the camera.

1

8.Youcan seethevideo and listento the voice through the television or monitor, adjust the place of the camera, aim at the monitor object then can make the valid monitoring, can adjust thevoiceby"vol+"r "vol-"key of_the remote controller, can change the channel in

turn

by the "CH

*", "CII-

"key.

9. Press the ON/OFF key of the remote controller, or pressthe channel button on the receiver

for

3 seconds to turn

off

the power of the receiver.

IV. The

familiar problems

and

solutions:

1.The indicator of the channel display window

is

not lighting.

Check whether the socketofthe power adapterworks well or not, and make sure the power switch is on.

2. The receiver cannot receive picture or the received picture flashes.

o Please checkwhether the wireless camera have already

put

connected with power.

aWhetherthe distance between wireless camera and receiver is too

faror

whether there is electromagnetic shielding barrierbetweenwireless camera and receiver

( eg: Building

of

steel structure will make much hindrance for transmitting signal).

3

oDon't make two wirelesscameras withthesame frequency work at the same time, otherwise they will cause interference.

o When the transmitting cameras of different frequency work at the same time, the distance between the cameras should be kept about or over 2 meters, otherwise receiving will be interfered.

O

lf

there are high-power transmission signals with the same frequency and car-mounted radio working around, they will cause interference to the receiver'

V.

Accessories:

l.Antenna

2. AV

Line

3. DC12V/500mA Power

I

Pcs

2 Pcs adaPter lPcs

4.

Manual

5. Camera (2.4G)

1

Pcs l-4pcs optional

6. Camera power adapter l-4pcs optional

Warranty

card

This card is an important evidence to receive our service, please keep it well.

@ When used normally, the following services can be offered:

A.Repair free ofcharge for functional disorder within I year.

B.Service for all the life( only charge material cost and freight ifthe warranty date expires.)

O The following conditions are excluded for warranty service

( repairable ifneeded, but will charge material cost and repair charge.)

A.Malfunctions or damages by incorrect installation or the using ofthe products exceeds the limited operating conditions.

B.Malfunctions or damages by repair and any other misuse.

C.Spare parts missed,artificial damages

D.Unmatchable products.

@ Repair cycle

Excluding the shipping dates, the quality department will submit the examine report in one day on receipt ofthe products, the products on the quantity under 50 setswill be repaired in

3 days after customers signed back the test report.

Product name

User's name:

User's address:

Tel

Purchase date

Invoice No.:

Distributor:

Contact person

Zip code

Tel:

Dealer:( Valid by sealed)