Polycom UC Software 4.1.5 Release Notes

Polycom UC Software 4.1.5 Release Notes
RELEASE NOTES
Software 4.1.5 | August 2013 | 3804-11530-415
Polycom® UC Software 4.1.5
Applies to the Polycom® VVX® 300/310, VVX® 400/410, VVX® 500,
and VVX® 600 Business Media Phones
1
Polycom UC Software 4.1.5 Release Notes
Copyright ©2013, Polycom, Inc. All rights reserved. No part of this document may be reproduced, translated into
another language or format, or transmitted in any form or by any means, electronic or mechanical, for any purpose,
without the express written permission of Polycom, Inc.
6001 America Center Drive
San Jose, CA 95002
USA
Trademarks
Polycom®, the Polycom logo and the names and marks associated with Polycom products are trademarks and/or
service marks of Polycom, Inc. and are registered and/or common law marks in the United States and various other
countries. All other trademarks are property of their respective owners. No portion hereof may be reproduced or
transmitted in any form or by any means, for any purpose other than the recipient's personal use, without the express
written permission of Polycom.
End User License Agreement
By installing, copying, or otherwise using this product, you acknowledge that you have read, understand and agree to
be bound by the terms and conditions of the End User License Agreement for this product.
Patent Information
The accompanying product may be protected by one or more U.S. and foreign patents and/or pending patent
applications held by Polycom, Inc.
Open Source Software Used in this Product
This product may contain open source software. You may receive the open source software from Polycom up to
three (3) years after the distribution date of the applicable product or software at a charge not greater than the
cost to Polycom of shipping or distributing the software to you. To receive software information, as well as the open
source software code used in this product, contact Polycom by email at OpenSourceVideo@polycom.com.
Disclaimer
While Polycom uses reasonable efforts to include accurate and up-to-date information in this document, Polycom
makes no warranties or representations as to its accuracy. Polycom assumes no liability or responsibility for any
typographical or other errors or omissions in the content of this document.
Limitation of Liability
Polycom and/or its respective suppliers make no representations about the suitability of the information contained in
this document for any purpose. Information is provided “as is” without warranty of any kind and is subject to change
without notice. The entire risk arising out of its use remains with the recipient. In no event shall Polycom and/or its
respective suppliers be liable for any direct, consequential, incidental, special, punitive or other damages whatsoever
(including without limitation, damages for loss of business profits, business interruption, or loss of business
information), even if Polycom has been advised of the possibility of such damages.
Customer Feedback
We are striving to improve our documentation quality and we appreciate your feedback. Email your opinions and
comments to DocumentationFeedback@polycom.com.
Visit the Polycom Support Center for End User License Agreements, software downloads, product
documents, product licenses, troubleshooting tips, service requests, and more.
Polycom, Inc.
2
Contents
General ......................................................................................... 6
What’s in These Release Notes? .................................................................................................... 6
Important Upgrade Notes and Considerations in UC Software ................................................... 7
Upgrading to or Downgrading from UC Software 4.1.x ................................................................... 7
Understanding Phone Features and Licenses .............................................................................. 7
Downloading the Distribution Files ................................................................................................ 8
Downloading the Combined ZIP File ............................................................................................... 8
Understanding the Split ZIP Resource Files .................................................................................. 10
What’s New for Polycom UC Software 4.1.5? ......................... 13
New or Enhanced Features............................................................................................................ 13
Enhanced Capabilities ................................................................................................................... 13
Configuration File Enhancements ................................................................................................ 18
Updates to Previous Software Releases ................................. 19
Understanding Updates to UC Software 4.1.4 ............................................................................. 19
New or Enhanced Features ........................................................................................................... 19
Enhanced Capabilities ................................................................................................................... 19
Understanding Updates to UC Software 4.1.3 Rev G .................................................................. 19
New or Enhanced Features ........................................................................................................... 20
Enhanced Capabilities ................................................................................................................... 20
Configuration File Enhancements .................................................................................................. 22
Understanding Updates to UC Software 4.1.3 ............................................................................. 23
New or Enhanced Features ........................................................................................................... 23
Enhanced Capabilities ................................................................................................................... 23
Configuration File Enhancements .................................................................................................. 24
Understanding Updates to UC Software 4.1.2 Rev B .................................................................. 32
New or Enhanced Features ........................................................................................................... 33
Enhanced Capabilities ................................................................................................................... 33
Understanding Updates to UC Software 4.1.2 ............................................................................. 33
New or Enhanced Features ........................................................................................................... 33
Enhanced Capabilities ................................................................................................................... 34
Configuration File Enhancements .................................................................................................. 34
Understanding Updates to UC Software 4.1.0 Rev B .................................................................. 35
New or Enhanced Features ........................................................................................................... 35
Enhanced Capabilities ................................................................................................................... 36
Configuration File Enhancements .................................................................................................. 36
Understanding UC Software 4.1.0 for the SpectraLink 84xx and VVX 500 ............................... 36
New or Enhanced Features ........................................................................................................... 36
Enhanced Capabilities ................................................................................................................... 37
Configuration File Enhancements .................................................................................................. 39
3
Polycom UC Software 4.1.5 Release Notes
Understanding Updates to UC Software 4.0.2 Rev B .................................................................. 41
New or Enhanced Features ........................................................................................................... 41
Enhanced Capabilities ................................................................................................................... 41
Configuration File Enhancements .................................................................................................. 43
Understanding Updates to UC Software 4.0.2 (Limited Release) .............................................. 43
New or Enhanced Features ........................................................................................................... 44
Enhanced Capabilities ................................................................................................................... 44
Configuration File Enhancements .................................................................................................. 45
Understanding Updates to UC Software 4.0.1B .......................................................................... 46
Understanding Updates to UC Software 4.0.1 ............................................................................. 46
New or Enhanced Features ........................................................................................................... 46
Enhanced Capabilities ................................................................................................................... 49
Configuration File Enhancements .................................................................................................. 52
Understanding Updates to UC Software 4.0.0 ............................................................................. 54
New or Enhanced Features ........................................................................................................... 54
Enhanced Capabilities ................................................................................................................... 57
Configuration File Enhancements .................................................................................................. 63
Understanding Updates to UC Software 3.3.2 ............................................................................. 77
New or Enhanced Features ........................................................................................................... 77
Enhanced Capabilities ................................................................................................................... 78
Configuration File Enhancements .................................................................................................. 82
Understanding Updates to UC Software 3.3.1F ........................................................................... 87
Enhanced Capabilities ................................................................................................................... 87
Understanding Updates to UC Software 3.3.1 ............................................................................. 88
New or Enhanced Features ........................................................................................................... 88
Enhanced Capabilities ................................................................................................................... 89
Configuration File Enhancements .................................................................................................. 91
Understanding Updates to UC Software 3.3.0 ............................................................................. 92
New or Enhanced Features ........................................................................................................... 92
Discontinued Features ................................................................................................................... 95
Enhanced Capabilities ................................................................................................................... 95
Configuration File Enhancements ................................................................................................ 103
Understanding Updates to SIP 3.2.5 ........................................................................................... 104
New or Enhanced Features ......................................................................................................... 104
Enhanced Capabilities ................................................................................................................. 104
Configuration File Enhancements ................................................................................................ 106
Understanding Updates to SIP 3.2.4B ........................................................................................ 107
Enhanced Capabilities ................................................................................................................. 107
Understanding Updates to SIP 3.2.4 ........................................................................................... 107
Enhanced Capabilities ................................................................................................................. 107
Understanding Updates to SIP 3.2.3 ........................................................................................... 108
New or Enhanced Features ......................................................................................................... 108
Enhanced Capabilities ................................................................................................................. 108
Configuration File Enhancements ................................................................................................ 110
Understanding Updates to SIP 3.2.2 ........................................................................................... 112
New or Enhanced Features ......................................................................................................... 112
Discontinued Features ................................................................................................................. 113
Enhanced Capabilities ................................................................................................................. 113
Configuration File Enhancements ................................................................................................ 115
Polycom, Inc.
4
Polycom UC Software 4.1.5 Release Notes
Understanding Updates to SIP 3.2.1B ........................................................................................ 120
New or Enhanced Features ......................................................................................................... 120
Configuration File Enhancements ................................................................................................ 120
Understanding Updates to SIP 3.2.1 ........................................................................................... 121
Enhanced Capabilities ................................................................................................................. 121
Understanding Updates to SIP 3.2.0 ........................................................................................... 121
New or Enhanced Features ......................................................................................................... 121
Discontinued Features ................................................................................................................. 123
Enhanced Capabilities ................................................................................................................. 123
Configuration File Enhancements ................................................................................................ 131
Understanding Updates to SIP 3.1.7 ........................................................................................... 142
New or Enhanced Features ......................................................................................................... 142
Enhanced Capabilities ................................................................................................................. 142
Configuration File Enhancements ................................................................................................ 145
Known Issues and Suggested Workarounds ....................... 147
Reference Documents ............................................................ 156
Polycom, Inc.
5
General
®
Polycom Unified Communications (UC) software 4.1.5 is a general release for all open SIP platforms or
®
®
®
®
for Microsoft Lync Server 2010 and Microsoft Lync Server 2013. Polycom UC software 4.1.5 supports
the following phone platforms:
 Polycom VVX 300/310 business media phone
®
®
 Polycom VVX 400/410 business media phone
®
®
 Polycom VVX 500 business media phone
®
®
 Polycom VVX 600 business media phone
®
®
Note: End User License Agreement
Read the terms and conditions in the end user license agreement for Polycom VVX software
products before you start using UC software 4.1.5.
Note: Registering with Lync Server
If you are using Polycom UC software 4.1.5 with Microsoft Lync Server, you can only register one
line. You cannot use UC software 4.1.5 to register multiple lines on a phone with Lync Server.
These release notes provide important information on software updates, phone features and feature
licenses, and known issues. In addition, these release notes refer to previous UC software versions to
assist administrators who are updating to a UC software 4.1.5 release from an earlier software release.
What’s in These Release Notes?
The Polycom UC software 4.1.5 Release Notes contain the following sections:
 General Read this section to understand how the changes in UC software 4.1.5 affect Polycom
hardware, deployment, and configuration of the software.
 What’s New for Polycom UC Software 4.1.5?
software features.
 Updates to Previous Software Releases
features in previous software releases.
This section lists enhanced and discontinued software
 Known Issues and Suggested Workarounds
workarounds, if available.
 Reference Documents
This section lists new, enhanced, and discontinued
This section lists existing known issues and suggests
This section lists all documents relevant to these release notes.
6
Polycom UC Software 4.1.5 Release Notes
Important Upgrade Notes and Considerations in UC Software
This section contains important notes on Polycom hardware and UC software.
Upgrading to or Downgrading from UC Software 4.1.x
As of UC software 4.x.x, Polycom has changed the process of upgrading and downgrading software on
the phones. To upgrade to UC software 4.1.x, you will first need to install the new Upgrader application.
Once you have installed the Upgrader, you can install UC software 4.1.x.
To downgrade from UC software 4.1.x, you will first need to install a new application called the
Downgrader. Once you have installed the Downgrader, you can install an earlier UC software version.
For detailed instructions on how to upgrade and downgrade your UC software, see Engineering Advisory
64731: Polycom® UC Software 4.0.x: Upgrade and Downgrade Methods.
Note: Understanding UC Software Versions
To understand which version of UC software can be used with Polycom phones, and for access to
major supporting documentation for each UC software version, use the SIP/UC Software Downloads
Matrix.
Understanding Phone Features and Licenses
The phone features and licenses required to operate a feature vary by phone model. Use this section to
find out which phone features and licenses you require for your phone model.
The following table lists features available for each phone model and indicates whether or not a feature
license is required.
Use Table 1: VVX Series Features and Licenses if you are deploying VVX 300/310, VVX 400/410, VVX
500, or VVX 600 business media phones. In the following table, (No) indicates that a phone does not
support a feature, (Yes) indicates a phone supports a feature and no license is required, and (Yes*)
indicates that the phone requires a feature license to support a feature.
Table 1: VVX Series Features and Licenses
Feature
VVX 300/310
VVX 400/410
VVX 500
VVX 600
VQMon
Yes*
Yes*
Yes (Audio only)
Yes (Audio only)
Call Recording
Yes
Yes
Yes
Yes
Conference
Management
Yes
Yes
Yes
Yes
Electronic Hookswitch
Yes
Yes
Yes
Yes
Polycom, Inc.
7
Polycom UC Software 4.1.5 Release Notes
Feature
VVX 300/310
VVX 400/410
VVX 500
VVX 600
Enhanced Feature
Keys
Yes
Yes
Yes
Yes
Customizable UI
Background
Yes
Yes
Yes
Yes
Asian Languages
Yes
Yes
Yes
Yes
Enhanced BLF
Yes
Yes
Yes
Yes
*Feature License needs to be purchased from Polycom.
Downloading the Distribution Files
You can download UC software 4.1.5 using the combined or the split file in ZIP file format. For general
use, Polycom recommends using the split resource file that corresponds to the phone model(s) for your
deployment. Use Table 3: Understanding the Split ZIP Resource Files to match the correct UC software
resource file to your phone model. If you are provisioning your phones centrally using configuration files,
download the corresponding resource file and extract the configuration files to the provisioning server,
maintaining the folder hierarchy in the ZIP file.
The current build ID for the sip.ld and resource files is UCS 4.1.5.3071.
Downloading the Combined ZIP File
Use Table 2: Understanding the Combined ZIP File as a reference guide to each of the files distributed in
the combined ZIP file and a brief description of each file.
Table 2: Understanding the Combined ZIP File
Distributed Files
File Purpose and Application
sip.ld
Concatenated SIP application executable
sip.ver
Text file detailing build-identification(s) for the release
000000000000.cfg
Master configuration template file
000000000000-directory~.xml
Local contact directory template file. To apply on a per phone basis, replace
the 0s with the MAC address of the phone and remove ‘~’ from the file
name.
applications.cfg
Contains configuration parameters for microbrowser and browser
applications
features.cfg
Contains configuration parameters for telephony features
H323.cfg
Contains configuration parameters for the H.323 signaling protocol
Polycom, Inc.
8
Polycom UC Software 4.1.5 Release Notes
Distributed Files
File Purpose and Application
reg-advanced.cfg
Contains configuration parameters for line and call registration and
advanced phone feature settings
reg-basic.cfg
Contains configuration parameters for line and call registration and basic
phone settings
region.cfg
Contains configuration parameters for regional and localization settings
such as time and date and language
sip-basic.cfg
Contains configuration parameters for the VoIP server and softswitch
registration
sip-interop.cfg
Contains configuration parameters for the VoIP server, softswitch
registration, and interoperability configuration
site.cfg
Contains configuration parameters that are set on a per site basis
video.cfg
Contains configuration parameters for video connectivity
video-integration.cfg
Contains configuration parameters for SoundStation IP 7000 and Polycom
HDX integration
Polycom, Inc.
9
Polycom UC Software 4.1.5 Release Notes
Distributed Files
File Purpose and Application
SoundPointIP-dictionary.xml
Includes native support for the following languages:

Chinese, Traditional (for IP 321, 331, 335, 450, 550, 560, 650, 670;
IP 5000, 6000, 7000, Duo)

Chinese, Simplified (for IP 321, 331, 335, 450, 550, 560, 650, 670; IP
5000, 6000, 7000, Duo)

Danish, Denmark

Dutch, Netherlands

English, Canada

English, United Kingdom

English, United States

French, France

German, Germany

Italian, Italy

Japanese, Japan (for IP 450, 550, 560, 650, 670; IP 5000, 6000,
7000, Duo)

Korean, Korea (for IP 450, 550, 560, 650, 670; IP 5000, 6000, 7000,
Duo)

Norwegian, Norway

Polish, Poland

Portuguese, Portugal

Russian, Russia

Slovenian, Slovenia

Spanish, Spain
 Swedish, Sweden
SoundPointIPWelcome.wav
Start up welcome sound effect
LoudRing.wav
Loud ringer sound effect
Warble.wav
Loud ringer sound effect
Understanding the Split ZIP Resource Files
Polycom recommends using the split ZIP file to shorten upgrade times. Use Table 3: Understanding the
Split ZIP Resource Files to find the split resource file for your phone model.
Table 3: Understanding the Split ZIP Resource Files
Resource Files
File Purpose and Application
3111-46135-002.sip.ld
SIP application executable for VVX 300
3111-46161-001.sip.ld
SIP application executable for VVX 310
Polycom, Inc.
10
Polycom UC Software 4.1.5 Release Notes
Resource Files
File Purpose and Application
3111-46157-002.sip.ld
SIP application executable for VVX 400
3111-46162-001.sip.ld
SIP application executable for VVX 410
3111-44500-001.sip.ld
SIP application executable for VVX 500
3111-44600-001.sip.ld
SIP application executable for VVX 600
sip.ver
Text file detailing the build-identification(s) for the release
000000000000.cfg
Master configuration template file
000000000000-directory~.xml
Local contact directory template file. To apply on a per-phone basis, replace
the 0s with the MAC address of the phone, and remove ‘~’ from the file
name.
applications.cfg
Contains configuration parameters for microbrowser and browser
applications
device.cfg
Contains Network Configuration device parameters
features.cfg
Contains configuration parameters for telephony features
firewall-nat.cfg
Contains Firewall parameters. Typical MS LYNC Environment
lync.cfg
Contains LYNC specific configuration parameters
pstn.cfg
Contains parameters for PSTN Use
reg-advanced.cfg
Contains configuration parameters for the line and call registration and
advanced phone feature settings
reg-basic.cfg
Contains configuration parameters for the line and call registration and
basic phone feature settings
region.cfg
Contains configuration parameters for regional and localization settings
such as time and date and language
sip-basic.cfg
Contains configuration parameters for the VoIP server, soft switch
registration
sip-interop.cfg
Contains configuration parameters for the VoIP server, soft switch
registration, and interoperability configuration
site.cfg
Contains configuration parameters that are set on a per-site basis
Polycom, Inc.
11
Polycom UC Software 4.1.5 Release Notes
Resource Files
File Purpose and Application
SoundPointIP-dictionary.xml
Includes native support for the following languages:

Chinese, Traditional (for IP 321, 331, 335, 450, 550, 560, 650, IP
5000, Duo)

Chinese, Simplified (for IP 321, 331, 335, 450, 550, 560, 650 IP
5000, Duo)

Danish, Denmark

Dutch, Netherlands

English, Canada

English, United Kingdom

English, United States

French, France

German, Germany

Italian, Italy

Japanese, Japan (for IP 450, 550, 560, 650, IP 5000, Duo)

Korean, Korea (for IP 450, 550, 560, 650, IP 5000, Duo)

Norwegian, Norway

Polish, Poland

Portuguese, Portugal

Russian, Russia

Slovenian, Slovenia

Spanish, Spain
 Swedish, Sweden
SoundPointIPWelcome.wav
Start-up welcome sound effect
LoudRing.wav
Loud ringer sound effect
Warble.wav
Loud ringer sound effect
Polycom, Inc.
12
What’s New for Polycom UC Software
4.1.5?
Polycom Unified Communications (UC) software 4.1.5 is a general release for all open SIP platforms or
for Microsoft Lync Server 2010 and Microsoft Lync Server 2013. Note that if you are using Polycom UC
software 4.1.5 with Microsoft Lync Server, you can only register one line. You cannot use UC software
4.1.5 to register multiple lines on a phone with Lync Server.
Polycom UC software 4.1.5 supports the following phone platforms:
 Polycom VVX 300/310 business media phone
 Polycom VVX 400/410 business media phone
 Polycom VVX 500 business media phone
 Polycom VVX 600 business media phone
This section lists all changes, additions, removals, enhancements, and configuration file parameter
changes to UC software 4.1.5 beside their respective Polycom tracking identification number.
New or Enhanced Features
84966 Added support to handle URIs up to 256 characters in length.
85344 Added a Lync status menu on the phone's web interface.
Enhanced Capabilities
72893 Date format options on the phone’s web interface are improved when the Chinese language is
configured.
76468 In a Hoteling scenario, the phone now fetches the previous status of the guest after a reboot.
76769/82121
Calls without SIP DISPLAY INFO now log under the missed or received call lists.
79064/84264 A call initiated from the phone now successfully fails over to the second server when the
primary server fails during the call initiation.
79638/84307 The phone no longer plays the message waiting tone when all pending pages are
received.
79723/80958 The phone now plays 183 early media and 180 local ringback independently and one after
the other.
80852/84844 The phone’s touch screen responsiveness after a call or after using an application is
improved (applies to VVX 500 and VVX 600).
81327/84602 Changing the static BLF line key configurations on the web interface no longer causes any
effect on the configured soft keys.
81422 The caller name with quotes (') or double quotes (") now displays on the caller screen without any
issue.
13
Polycom UC Software 4.1.5 Release Notes
82044 The phone’s menu is now optimized to hide all the soft key impressions of the previous menu.
82319/83255/83806/83834/82286/86548 The phone now displays all the new pop-ups and strings in
the configured language instead of the default language.
82781 In a call forward scenario with Lync deployment, the phone now shows the details of both the
caller and the call forwarder.
83619/86104/87146 The phone now sends 'A' as the standard query to the DNS server when the phone
uses IPv4.
82630/80609/82970 The phone no longer goes to the DND active state after a reboot when the DND
feature is disabled on the server, and the parameter reg.x.serverFeatureControl.dnd is
set to 1.
83708 The phone now successfully answers an incoming call when it is transferred through the
Exchange Auto Attendant.
83776 The phone’s idle browser no longer displays the “invalid host name” error after a reboot or restart.
83806/84304/86642/87028/88324/88325 The “Clear browsing data” and “Return to calls” strings on the
phone’s menu display in the configured language.
83854 In a BLF scenario, the New Call soft key now displays on the incoming call screen of the
monitoring user when there is an incoming call to one of the monitored users.
84140/84834 When the phone sends a TCP SYN request and does not receive any response, the
phone now switches to the failover server.
84161/80529/87856 The selection of ringtone patterns in multiple scenarios is optimized.
84271/82209 The date and time are now arranged successfully on the phone screen using the
parameters lcl.ml.lang.clock.1.dateTop and lcl.datetime.date.dateTop.
84471/84341 The graphical user interface response on the phone is improved when the phone is used
for a long time.
84514 The phone’s web interface now accepts a blank admin password.
84534/82075 The phone is now able to park and retrieve the call successfully from the park orbit when
the parameters reg.1.lineKeys and reg.1.callsPerLineKey are set to 1.
84643 In a Lync environment, the phone now correctly normalizes the emergency E911 dial plan.
84645 In a call forward scenario, the phone now displays an error message when the server rejects the
call forward setting.
84664 The phone now returns to the idle screen when the user presses any termination key without
initiating a call from the directory menu on the dialer screen.
84717 The web browser now displays the volume index bar on the phone’s screen when the user tries to
increase the volume for a media file.
84799 The phone now answers an incoming call automatically, without any issues, when the auto
answer is configured.
84803 In a BLF scenario, the monitoring phone can now establish calls when one of its monitored lines
is on a call and attendant.resourceList.1.type="automata",
attendant.behaviors.display.spontaneousCallAppearances.normal="0" are set.
Polycom, Inc.
14
Polycom UC Software 4.1.5 Release Notes
84811/83432 The line label now displays the configured Chinese characters in the call logs screen of
the phone.
84815 While using the Polycom Desktop Connector, the ‘<<’ soft key is now available on the phone’s
screen when the user tries to edit the Desktop User option.
84823 Audio quality on the speaker is improved when the user mutes and unmutes the speaker while
receiving a page.
84905 The More soft key no longer displays on the ACD queue status pop-up when the user acts as an
agent.
84909 Answering an incoming call from E911 is now available when the phone is in a locked state.
84928/85674
Call logs of the phone now update the PSTN calls properly without any issue.
84931 The power saving state on the phone is now optimized while using the BroadSoft Event Hoteling
package (applies to VVX 500).
84974 Enabling call forward using the phone’s web interface is now available.
85034 Pressing the Select hard key in the phone’s corporate directory now displays the details of the
contact on the phone’s screen.
85105 The Hold/Mute keys are now non-functional when the user tries to place a call in a locked state.
85109/84725/84428/84892 The subnet mask now correctly updates on the phone’s screen and the serial
port when the DHCP sends an option 43 vendor class.
85373 In a Lync environment, the phone now retains the registration when federated contacts (~60) are
added and receives 504 server timeout errors from the server.
85403 In a Lync call server deployment, the phone now adds the ‘+’ prefix automatically for emergency
E911 dialing, irrespective of the dial plan.
85408/87180 The ringback for outbound PSTN calls is now optimized and no longer produces any
double ringback.
85651 In the ACD scenario, the phone now retains the ACD icon when the server-based call forward is
enabled.
85675/85676/85369 In a Lync environment, the user now successfully signs in when the root certificate
is downloaded using DHCP option 43.
85711/86579 In a Lync environment, users now successfully sign in using Pin-Authentication when the
pin contains leading zeros.
85728/86157 In a shared call scenario, the LED or line status on the phone now changes and shows a
solid red color when the incoming call is answered by one of the remote destinations.
85794/86721 The phone now sends a publish request to the VQMon server when the VQMon server is
configured with the fully qualified domain name (FQDN).
85947/84435/86548 Strings and phrases in various language directories are improved, and the
unwanted spaces are removed.
85962/85984/86764 The phone now displays both the Start and Ping soft keys when the user tries to
trace an IP from the phone’s menu for the second time immediately after cancelling the first
attempt.
Polycom, Inc.
15
Polycom UC Software 4.1.5 Release Notes
86054 The phone now successfully receives the ICMP message "Fragmentation needed" without any
failover.
86064 During auto discovery, the phone now includes the IP address by comparing the domain name in
the sign-in address with the domain name in the DCHP option 120.
86075 Sending a voicemail from the phone is now available without any issue when the parameters
msg.mwi.1.callBackMode="contact" and msg.mwi.1.callBack="voicemail" are
configured (applies to VVX 400/410).
86206 The phone now displays only the Conf soft key in the active call state when the parameter
softkey.feature.basicCallManagement.redundant is set to 0.
86237 The phone gets a grace period of an extra 25% of the validity date of the TLS-DSK certificate and
does not get de-registered during that period.
86261 The phone now establishes a two-way audio path when the BroadWorks Anywhere extensions
are configured as mobile or PSTN numbers.
86276/86767 The phone no longer updates the directory.xml file when the presence of the monitored
buddy changes.
86277 The phone now honors the 302 moved temporary request and performs the corresponding DNS
lookup without any issue.
86425/84572 The phone’s status menu now updates the AOR details with the primary server when
there are two active servers for a single registered number.
86568 The user can successfully disable the call forward no answer from the phone’s screen when the
parameter reg.1.serverFeatureControl.cf is set to 1.
86575/85968/84650/83991 The phone now successfully downloads the updates from the macdirectory.xml file and modifies the speed dial list accordingly.
86623 The phone now plays the defined custom ringtone for a directory contact.
86636 In a call center environment, the LED status on the phone now updates correctly for an incoming
call on a shared line (applies to VVX 300/310 and VVX 400/410).
86709/85370 The call logs menu on the phone will now not get updated for the missed calls when the
parameter call.advancedMissedCalls.reasonCodes=487 is set (applies to VVX 500 and
VVX 600).
86730/86869/87504 The phone now transfers a call successfully when the language is set to German,
Japanese, Chinese, Taiwanese, and Korean.
86772 Soft key strings on the phone’s microbrowser now format correctly for French.
86873/86256/86569/85368/85957 In a Lync deployment, the phone’s stability is improved for different
network environments.
86877/84668 When there are no entries present on the phone’s dialer screen, the Send soft key no
longer displays (applies to VVX 400/410).
86908/86909/87873 In a Lync environment, the phone will dial the entered number according to the
dialplan.1.lyncdigitmap.timeout parameter.
87025 A power saving menu is now available on the phone’s web interface (applies to VVX 300/310 and
VVX 400/400).
Polycom, Inc.
16
Polycom UC Software 4.1.5 Release Notes
87026 A password field entry page now displays on the phone’s screen when the user tries to answer an
incoming call in the locked state.
87029 The MWI LED no longer blinks when the phone is in power saving mode and has not received
any new message.
87031 The phone now retains the configured language even after a reboot.
87032 In a BLF scenario, the phone shows only the LED activity and does not show the call appearance
when attendant.behaviors.display.spontaneousCallAppearances.normal is set to
0.
87059 Sending a visual voicemail from the phone is now available when the VVX camera is not
attached, and the video.enable parameter is set to 1.
87063 The phone now accepts the MIME message without a SDP and no longer sends a 415 error
message.
87075 Placing an emergency call from an unregistered phone is now available from all the call
terminations.
87076 The enhanced feature key $Tinvite now works and no longer causes the phone to reboot.
87092 The phone now establishes a two-way audio when the video is disabled, and a BroadWorks
Anywhere extension is configured.
87096 The Log-in soft key is now available on the phone after a software upgrade without needing to
change the configuration.
87112 Upgrading the touch screen firmware displays only the visual indicators and no longer shows the
progress bar.
87114 Accessing the phone menu in the locked state is no longer available when the parameter
up.idleStateView is set to 1.
87115 The phone is now able to perform Transfer or Conference functions when an incoming call is
answered in a locked state by entering the password.
87151 Enhanced feature keys like Blind Transfer and Voice Mail Transfer now work without any issue.
87220 Contact information of the caller is no longer shown on the phone’s screen when caller ID is
disabled on the server.
87394/87599 In a call center environment, the phone no longer produces any beep sound when one of
its monitored phones has its handset lifted, or receives a call, or goes off hook using any
termination.
87440/87098 The digit map value now displays as empty on the phone’s web interface when the
reg.1.applyServerDigitMapLocally is set to 0.
87453/87632/87262 The phone now establishes a two-way audio path without any issues after
successfully establishing a number of (~50) PTT and paging calls.
87560/87422 The phone’s microbrowser invokes a backspace soft key (for non-touch based phones) or
an on-screen key board (for touch based phones) when the user tries to enter numeric values.
87679 The phone no longer displays the “Please try again” message when the parameters
reg.1.serverFeatureControl.cf="1", reg.1.server.1.expires="10" are set.
Polycom, Inc.
17
Polycom UC Software 4.1.5 Release Notes
87792 The phone lock feature is now redesigned. The phone will not return to the locked state after
answering a call by entering the password from the locked phone.
87890 The ethernet port information of the phone now displays correctly when the LLDP mode is
enabled.
87891/87062 The phone’s screen now updates without any issue while using hookswitch in quick
succession.
Configuration File Enhancements
Refer to the following table for a list of all enhancements made to the UC software 4.1.5 configuration file
parameters.
Table 4: UC Software 4.1.5 Parameter Enhancements
Parameter
Permitted
Values
Default
Description
up.numOfDisplayColumns
0 to 4
3 (VVX 500),
4 (VVX 600)
4 lines display when parameter value
is 0 or 1.
8 lines display when parameter value
is 2.
12 lines display when parameter value
is 3.
12 lines (for VVX 500) and 16 lines (for
VVX 600) display when parameter
value is 4.
dialplan.1.lyncdigitmap.
timeout
1 to 99
3
Entered digits in the dial screen will
dial out automatically after the defined
timeout.
video.allowWithSource
0 or 1
0
If set to 1 and camera is detached, no
video codecs are advertised in SDP.
If set to 1 and camera is attached,
video codecs are advertised in SDP.
If set to 0 and camera is attached or
detached, video codecs are advertised
in SDP (default).
Polycom, Inc.
18
Updates to Previous Software Releases
This section lists enhanced and discontinued software features in previous software releases.
Understanding Updates to UC Software 4.1.4
Polycom Unified Communications (UC) software 4.1.4 is a general release for all open SIP platforms and
®
®
is compliant with Microsoft Lync Server 2010. Note that if you are using Polycom UC software 4.1.4
with Microsoft Lync Server, you can only register one line. You cannot register multiple lines on a phone
with Lync Server.
Polycom UC software offers support for the following phone platforms:
 VVX 300/310 business media phones
 VVX 400/410 business media phones
 VVX 500 business media phones
 VVX 600 business media phones
Note: Visual Voice Mail Not Supported
Visual Voice Mail support for the Metaswitch server is not fully qualified in this release and is
currently unavailable for these platforms.
This section lists all changes, additions, removals, enhancements, and configuration file parameter
changes to UC software 4.1.4 beside their respective Polycom tracking identification number.
New or Enhanced Features
71881 Added support for VVX 300/310 and VVX 400/410.
Enhanced Capabilities
No changes were made from the previous UC software release.
Understanding Updates to UC Software 4.1.3 Rev G
Polycom Unified Communications (UC) software 4.1.3 Rev G is a general release for all open SIP servers
including Microsoft Lync Server and is available on the following endpoint platforms:
 Polycom VVX 500 business media phone
 Polycom VVX 600 business media phone
 Polycom SoundStructure
19
Polycom UC Software 4.1.5 Release Notes
Note: VVX Camera Support
UC software 4.1.3 Rev G offers video support for the VVX Camera for all the open SIP servers
except Microsoft Lync. UC software 4.1.3 Rev G does support all other features of Microsoft Lync.
®
Web Info: Polycom BroadSoft UC-One Features and Configuration Details
For information on the Polycom BroadSoft UC-One features, available for the VVX 500 and VVX
600 business media phones, and configuration procedures, see Feature Profile 84393: Using the
Polycom BroadSoft UC-One Application on Polycom VVX Business Media Phones on the Polycom
Support web site.
This section lists all changes, additions, removals, enhancements, and configuration file parameter
changes to UC software 4.1.3 Rev G beside their respective Polycom tracking identification number.
New or Enhanced Features
79861 Added support for BroadSoft directory search, presence and favorites.
84273 A video mute icon is now displayed on the phone’s local video pane when the VVX camera
shutter is closed.
Enhanced Capabilities
85148/84908 In the locked state, the phone no longer initiates the call to the emergency 911 upon offhooking the handset twice in quick succession, i.e. within 2 seconds.
84954 SoundStructure Studio now shows the correct status when the SoundStructure card is restarted
from the web configuration page.
84943/84991
The phone now supports long URIs up to 256 characters in length.
84651 In a BLF scenario, the phone is now able to answer an incoming call using a headset when one
of the monitored users is in an active/altering state (applies to VVX 500).
84608/84751 The parameter voIpProt.SIP.supportFor100rel is introduced for handling 1XX
provisional responses.
84439 When both call servers fail, the phone first tries the primary server. It then fails over to the
secondary server and back to the primary server. This loop continues until the phone registers
with one of the servers.
84407/84390 In a conference call scenario, audio path loss is no longer observed when a Lync PC
client is re-added to a conference call with CX 600 and a video-enabled VVX phone (applies to
VVX 500 and VVX 600).
84299 Call appearance details on the studio UI console are now displayed when a call is made from a
private line (applies to SoundStructure).
84221 Establishing a federated call using the long URI from the phone contacts or quick dialed list is
now available without any issue.
Polycom, Inc.
20
Polycom UC Software 4.1.5 Release Notes
84138/84139 After a call, the presence status of the user is now updated correctly on the phone when
the parameter reg.1.callsPerLineKey is set to 1.
84019 Line key is now updated with a 10 digit number immediately after a successful Lync registration
(applies to SoundStructure).
83945 The phone is now able to auto answer an incoming call with multiple call-info headers without any
issue when the parameters voIpProt.SIP.alertInfo.1.value="auto-answer" and
voIpProt.SIP.alertInfo.1.class="autoAnswer" are set.
83781 The phone lock option has been removed (applies to SoundStructure).
83776 The idle browser on the phone appears automatically after a reboot/restart without displaying an
"Invalid Hostname" message.
83564/84405 On the Russian SKUs, only the SIP signaling is encrypted during in-band provisioning,
leaving the media unencrypted.
83460 The phone is now able to resume an outbound PSTN held call successfully when the user dials
the PSTN number without any area code.
83326 Scrolling through the contact directory’s menu using * or # is now working.
83308 During DND, the phone’s missed call lists are now correctly updated.
83069 Music on Hold (MOH) no longer disconnects when the phone is using SRTP traffic.
83022 The phones now send SIP INFO packet with a new line between content attributes.
82915 Added the configuration parameter tcpIpApp.sntp.AQuery. If set to 1, the phone will send a
DNS query directly for NTP requests.
82319/83255/83806/83834 The phone now displays all the new pop-ups and strings in the configured
language instead of the default language.
81639 The phone is now able to handle the bit rate mismatch during a call for G.722.1 codec by setting
the parameter voIpProt.SIP.fmtpMustForG7221 to 1.
81554 In a call center scenario, the phone now displays the correct status and soft keys on the phone's
screen after a reboot.
81327 Changing the static BLF line key configurations on the web interface no longer affects the
configured soft keys.
80578 Enabling the exchange calendar feature no longer causes problems when connecting to the
hosted exchange server.
80293 The “Service Unavailable” message is no longer displayed on the phone’s screen when a paging
soft key is enabled and then disabled.
80125 Quickly pressing ACD Sign-In/Sign-Out keys is now working properly and does not take the
phone to the service unavailable state.
79846 The phone now retains the server-based DND even after the phone is locked.
77877 Missed/received calls are now logged in the respective configured list when the parameters
call.advancedMissedCalls.enabled and
call.advancedMissedCalls.addToReceivedList are set.
77097 The phone’s user interface is now improved to handle 486busy response.
Polycom, Inc.
21
Polycom UC Software 4.1.5 Release Notes
Configuration File Enhancements
Refer to the following table for a list of all enhancements made to the UC software 4.1.3 Rev G
configuration file parameters.
Table 5: UC Software 4.1.3 Rev G Parameter Enhancements
Parameter
Permitted Values
Default
Description
feature.qml.enabled
0 or 1
0
If 1, the QML viewer is enabled on
phone. If 0, the viewer is disabled.
The viewer is used to load the QML
applications.
feature.broadsoftdir.enable
d
0 or 1
0
If 1, the BroadSoft Enterprise directory
is enabled. If 0, the directory is
disabled.
feature.broadsoftUcOne.
enabled
0 or 1
0
If 1, the BroadSoft UC-One feature is
enabled. If 0, the feature is disabled.
dir.broadsoft.xsp.address
Dotted-decimal IP
address or
hostname or FQDN
Null
The IP address or hostname of the
BroadSoft XSP server.
For example, http://xspidc1.asia.polycom.com.
dir.broadsoft.xsp.username
String
Null
The username used to authenticate
the BroadSoft XSP server.
dir.broadsoft.xsp.password
String
Null
The password used to authenticate the
BroadSoft XSP server.
feature.presence.enabled
0 or 1
0
To enable the BroadSoft Presence
dir.broadsoft.qml.home
String
"file:////usr/
local/apps
/BSD/BSD
.qml"
xmpp.1.auth.password
True/false
True (1)
Password used for XMPP registration.
When provisioned from CMA, the
value is set to the CMA account
password.
xmpp.1.dialMethod
String
min 0, max 256
sip
For "sip" dialing, the destination XMPP
URI is converted to a SIP URI, and the
first available SIP line is used to place
the call.
xmpp.1.enable
True/false
False(0)
Flag to determine if XMPP presence is
enabled
xmpp.1.jid
String
min 0, max 256
“”
Jabber identity used to register with
presence server
Polycom, Inc.
22
Polycom UC Software 4.1.5 Release Notes
Parameter
Permitted Values
Default
Description
xmpp.1.jid
Duplicate
xmpp.1.server
String
min 0, max 256
“”
Presence server IP or FQDN
xmpp.1. verifyCert
True/false
True(1)
Flag to determine if the phone should
verify the TLS certificate provided by
the XMPP presence server.
Understanding Updates to UC Software 4.1.3
Polycom Unified Communications (UC) software 4.1.3 is a general release for all open SIP servers and
offers video support for the VVX Camera on the following phone platforms:
 VVX 500 business media phone
 VVX 600 business media phone
UC software 4.1.3 does not support Lync video on Microsoft Lync Server. It does support all other
features on Microsoft Lync Server available in UC software 4.1.2.
This section lists all changes, additions, removals, enhancements, and configuration file parameter
changes to UC software 4.1.3 beside their respective Polycom tracking identification number.
New or Enhanced Features
62655 Added support for the Polycom VVX Camera.
82204 Added video support (SIP and H323) on VVX 500 and VVX 600 business media phones.
Enhanced Capabilities
84089 The phone does now not show the incoming call appearance pop-up for the second time when
the call is answered after the initial pop-up has timed out.
83752 The phone’s UI/display is improved when switching between active call and other menus.
83725/81683 The phone is now able to transfer the location information to E911 successfully using
NTLM credentials in MS Lync Server.
83716 In a BLF scenario, phone is now able to retain the monitored user when the registration switches
between private and shared.
83513 The phone is now equipped to display the E911 disclaimer pop-up when set on the Lync server.
83273 Muting and unmuting the call by double-tapping the mute area on Jabra 9465 USB headset/touch
control is now working as expected.
82898 Changing the SIP line to a “SIP + H.323” line using the phone’s web interface during an active
call does not cause any call drop or reboot.
Polycom, Inc.
23
Polycom UC Software 4.1.5 Release Notes
82282 Calendar parser on the phone is now able to correctly identify the 'dial in numbers' for conference
calls.
82149 In a BLF scenario, phone no longer displays the call appearance of the monitored parties when
the parameter
attendant.behaviors.display.spontaneousCallAppearances.normal="0" is set.
82073 Answering a call using EHS is now available on the phone when the BLF status is active for any
monitored user.
82051/81016 Blind transfer from the contact directory/recent call list/favorites is now working as
expected.
82005 When the URL dialing is disabled, and the user tries to transfer an active call made to a BLFmonitored line, the user will no longer see the prompt screen.
81541 In a call center scenario, the guest user is now able to sign out from the host phone in a single
attempt when the guest has already signed in or out once.
81504 In a call center scenario, phone now updates the previous state of the user after a line reregistration is performed.
81439 In a call center scenario, phone no longer displays “Back” soft key during an incoming call to an
ACD line.
81245 Incoming call pop-up will no longer flash on the phone’s screen when the call is answered after
10 seconds.
80959/79673/79242 Provisioning the phone using the SIP-TLS option is now functioning as expected.
79915 Local contact search on the phone now displays all the contacts when there is no search
criterion.
79330 The phone now allows the STP traffic from the phone’s PC port.
76769 Missed and received calls are now updated on the phone when the “SIP DISPLAY INFO” portion
is missing in the initial SIP INVITE.
75937 The phone’s browser now updates the content properly during scrolling when the toolbar is in a
hidden state.
74871 In a PTT call, a beep sound is now played on the phone from the first call, indicating the start of
voice transmission.
Configuration File Enhancements
Refer to the following table for a list of all enhancements made to the UC software 4.1.3 configuration file
parameters.
Table 6: UC Software 4.1.3 Parameter Enhancements
Parameter
Permitted Values
Default
Description
call.autoAnswer.H323
0 or 1
0
If 0, auto-answer is disabled for H.323
calls. If 1, auto-answer is enabled for
all H.323 calls.
Polycom, Inc.
24
Polycom UC Software 4.1.5 Release Notes
Parameter
Permitted Values
Default
Description
call.autoAnswer.videoMute
0 or 1
0
If 0, video begins transmitting (video
Tx) immediately after a call is autoanswered. If 1, video transmission
(video Tx) is initially disabled after a
call is auto-answered.
call.autoRouting.preference
line or protocol
line
If set to line, calls are placed via the
first available line, regardless of its
protocol capabilities. If the first
available line has both SIP and H.323
capabilities, the preferred protocol will
be used
(call.autoRouting.preferredProtocol). If
set to protocol, the first available line
with the preferred protocol activated is
used, if available. If not available, the
first available line will be used.
Note: Auto-routing is used when
manual routing selection features
(up.manualProtocolRouting)are
disabled.
call.autoRouting.preferred
Protocol
SIP or H323
SIP
If set to SIP, calls are placed via SIP if
available, or via H.323 if SIP is not
available. If set to H323, calls are
placed via H.323 if available, or via SIP
if H.323 is not available.
call.enableOnNotRegistered
0 or 1
1
If 1, users can make calls when the
phone is not registered. If 0, calls are
not permitted without registration.
Note: Setting this parameter to 1
allows VVX phones to make calls
using the H.323 protocol even though
an H.323 gatekeeper is not configured.
feature.audioVideoToggle.
enabled
0 or 1
0
If 0, the audio/video toggle feature is
disabled. If 1, the feature is enabled.
reg.x.protocol.H323
0 or 1
0
If 0, H.323 signaling is not enabled for
registration x. If 1, H.323 signaling is
enabled.
reg.x.server.H323.y.address
dotted-decimal IP
address or
hostname
Null
Address of the H.323 gatekeeper.
reg.x.server.H323.y.port
0 to 65535
0
Port to be used for H.323 signaling. If
set to Null, 1719 (H.323 RAS
signaling) is used.
reg.x.server.H323.y.expires
positive integer
3600
Desired registration period.
Polycom, Inc.
25
Polycom UC Software 4.1.5 Release Notes
Parameter
Permitted Values
Default
Description
sec.H235.mediaEncryption.
enabled
0 or 1
1
If 0, H.235 Voice Profile RTP media
encryption will be disabled. If 1, H.235
media encryption will be enabled and
negotiated when such encryption is
requested by the far end.
sec.H235.mediaEncryption.
offer
0 or 1
0
If 0, media encryption negotiations will
not be initiated with the far end. If 1
and
sec.H235.mediaEncryption.enabled is
also 1, media encryption negotiations
will be initiated with the far end.
However, successful negotiations are
not a requirement for the call to
complete.
sec.H235.mediaEncryption.
require
0 or 1
0
If 0, media encryption negotiations will
not be required. If 1 and
sec.H235.mediaEncryption.enabled is
also 1, media encryption negotiations
will be initiated or completed with the
far end; if negotiations fail, the call will
be dropped.
sec.srtp.lifetime
0, positive integer
minimum 1024 or
power of 2 notation
0
The lifetime of the master key used for
the cryptographic parameter in SDP.
The value specified is the number of
SRTP packets. If 0, the master key
lifetime is not set. If set to a valid value
(at least 1024, or a power such as
2^10), the master key lifetime is set.
When the lifetime is set, a re-invite with
a new key will be sent when the
number or SRTP packets sent for an
outgoing call exceeds half the value of
the master key lifetime.
Note: Setting this parameter to a nonzero value may affect the performance
of the phone. If you are using a VVX
Camera on a VVX 500 and 600 phone,
set to 2^31.
up.manualProtocolRouting
Polycom, Inc.
0 or 1
1
If 1, the user is presented with a
protocol routing choice in situations
where a call can be placed using either
protocol (for example, with SIP and
H.323 protocols). If 0, the default
protocol is used, and the user does not
choose.
26
Polycom UC Software 4.1.5 Release Notes
Parameter
Permitted Values
Default
Description
up.manualProtocolRouting.
softKeys
0 or 1
1
Choose whether you want to display
soft keys that control Manual Protocol
Routing options. When Soft Key
Control is enabled, you can use soft
keys to choose between the SIP or
H.323 protocol. When disabled, soft
keys for protocol routing will not
display. The soft keys are enabled by
default.
video.autoFullScreen
0 or 1
0
If 0, video calls only use the full screen
layout if it is explicitly selected by the
user. If 1, video calls use the full
screen layout by default, such as when
a video call is first created or when an
audio call transitions to a video call.
video.autoStartVideoTx
0 or 1
1
When enabled, video transmission to
the far side begins when you start a
call. When disabled, video
transmission does not begin until you
press the Video > Start Video soft
keys. This parameter controls video
sent to the far side. Video from the far
side will always be displayed if it is
available, and far side users can
control when to send video.
video.callMode.default
audio or video
audio
Allows the user to select the mode to
use when using SIP protocol only.
video.callRate
128 to 2048
512
The default call rate (in kbps) to use
when initially negotiating bandwidth for
a video call.
video.camera.brightness
0 to 6
3
Set brightness level. The value range
is from 0 (dimmest) to 6 (brightest).
video.camera.contrast
0 to 4
0
Set contrast level. The value range is
from 0 (no contrast increase) to 3
(most contrast increase), and 4 (noise
reduction contrast).
video.camera.flicker
Avoidance
1 to 2
1
Set flicker avoidance. If set to 1, 50Hz
AC power frequency flicker avoidance
(Europe/Asia). If set to 2, 60Hz AC
power frequency flicker avoidance
(North America).
Polycom, Inc.
27
Polycom UC Software 4.1.5 Release Notes
Parameter
Permitted Values
Default
Description
video.camera.frameRate
5 to 30
25
Set target frame rate (frames per
second). Values indicate a fixed frame
rate, from 5 (least smooth) to 30 (most
smooth).
Note: If video.camera.frameRate is set
to a decimal number, the value 25 is
used.
video.camera.saturation
0 to 6
3
Set saturation level. The value range is
from 0 (lowest) to 6 (highest).
video.camera.sharpness
0 to 6
3
Set sharpness level. The value range
is from 0 (lowest) to 6 (highest).
video.codecPref.H264
1 to 4
1
Specifies the video codec preferences.
video.codecPref.H263
3
video.dynamicControlMethod
0 or 1
0
If 1, the first I-Frame request uses the
method defined by
video.forceRtcpVideoCodecControl,
and subsequent requests alternate
between RTCP-FB and SIP INFO.
video.enable
0=Disable,
1=Enable
0
If 0, video is not enabled and all calls—
both sent and received—are audio
only. If 1, video is sent in outgoing calls
and received in incoming calls if the
other device supports video.
video.enable for VVX 500
video.enable for VVX 600
0
0
video.forceRtcpVideoCodec
Control
0 or 1
0
If set to 1, the phone is forced to send
RTCP feedback messages to request
fast update I-frames for all video calls
(the phone includes a=rtcp-fb in the
SDP). If 0, RTCP feedback messages
are not forced.
video.iFrame.delay
0 to 10, seconds
0
When non-zero, an extra I-frame is
transmitted after video starts. The
amount of delay from the start of video
until the I-frame is sent is configurable
up to 10 seconds. Use a value of 2
seconds if you are using this
parameter in a Microsoft Lync
environment.
video.iFrame.minPeriod
1 - 60
2
After sending an I-frame, the phone
will always wait at least this amount of
time before sending another I-frame in
response to requests from the far end.
Polycom, Inc.
28
Polycom UC Software 4.1.5 Release Notes
Parameter
Permitted Values
Default
Description
video.iFrame.onPacketLoss
0 or 1
0
If 1, an I-frame is transmitted to the far
end when a received RTCP report
indicates that video RTP packet loss
has occurred.
video.localCameraView.
fullscreen.enabled
0 or 1
1
Determines whether the local camera
view is shown in the full screen layout.
If set to 0, the local camera view is not
shown. If set to 1, the local camera
view is shown.
video.localCameraView.
fullscreen.mode
pip, side-by-side
pip
Determines how the local camera view
is shown. If set to pip, the local camera
view displays as a picture-in-picture
with the far end window. If set to sideby-side, the local camera view displays
side-by-side with the far end window.
video.maxCallRate
128 to 2048 kbps
768
The maximum call rate allowed. This
allows the administrator to limit the
maximum call rate that the users can
select. If video.callRate exceeds this
value, this value will be used as the
maximum.
video.profile.H263.CifMpi
1 to 32
1
Specify the frame rate divider that the
phone uses when negotiating Quarter
CIF resolution for a video call. You can
enter a value between 0-4. To disable,
enter ‘0’.
video.profile.H263.
jitterBufferMax
(video.profile.H263.
jitter BufferMin +
500ms) to 2500ms
2000ms
video.profile.H264.
jitterBufferMax
(video.profile.H264.
jitter BufferMin +
500ms) to 2500ms
The largest jitter buffer depth to be
supported (in milliseconds). Jitter
above this size will always cause lost
packets. This parameter should be set
to the smallest possible value that will
support the expected network jitter.
video.profile.H263.
jitterBufferMin
33ms to 1000ms
150ms
The smallest jitter buffer depth (in
milliseconds) that must be achieved
before play out begins for the first time.
Once this depth has been achieved,
the depth may fall below this point and
play out will still continue. This
parameter should be set to the
smallest possible value which is at
least two packet payloads and larger
than the expected short-term average
jitter.
video.profile.H264.
jitterBufferMin
Polycom, Inc.
29
Polycom UC Software 4.1.5 Release Notes
Parameter
Permitted Values
Default
Description
video.profile.H263.
jitterBufferShrink
33ms to 1000ms
70ms
The absolute minimum duration time
(in milliseconds) of RTP packet Rx with
no packet loss between jitter buffer
size shrinks. Use smaller values (33
ms) to minimize the delay on known
good networks. Use larger values
(1000ms) to minimize packet loss on
networks with large jitter (3000 ms).
video.profile.H263.
payloadType
96 to 128
34
RTP payload format type for H263
MIME type.
video.profile.H264.
payloadType
96 to 128
109
RTP payload format type for
H264/90000 MIME type.
video.profile.H264.
profileLevel
1, 1b, 1.1, 1.2, and
1.3 (1 to 2)
1.3
Specify the highest profile level within
the baseline profile supported in video
calls. The phone supports the following
levels: 1, 1b, 1.1, 1.2, 1.3. The default
level is 1.3. For more information, refer
to ITU-T H.264.
video.profile.H263.QcifMpi
1 to 32
1
Specify the frame rate divider that the
phone uses when negotiating Quarter
CIF resolution for a video call. You can
enter a value between 0-32. To
disable, enter ‘0’.
video.profile.H263.SqcifMpi
1 to 32
1
Specify the frame rate divider that the
phone uses when negotiating Sub
Quarter CIF resolution for a video call.
You can enter a value between 0-32.
To disable, enter ‘0’.
video.quality1
motion, sharpness
Null
The optimal quality for video that you
send in a call or a conference. Use
motion if your outgoing video will have
motion or movement. Use sharpness
or Null if your outgoing video will have
little or no movement.
video.profile.H264.
jitterBufferShrink
Note: If motion is not selected,
moderate to heavy motion can cause
some frames to be dropped.
Polycom, Inc.
30
Polycom UC Software 4.1.5 Release Notes
Parameter
Permitted Values
Default
Description
video.screenMode
normal, full, crop
normal
The screen mode for the video window
shown in non-full screen mode. If set
to normal or Null, the entire view is
displayed and horizontal or vertical
black bars may appear on the edges to
maintain the correct aspect ratio. If set
to full, the entire view is stretched
linearly and independently to fill the
video frame. If set to crop, black bars
are not shown, the image is re-sized
and enlarged to cover the entire video
frame, and parts of the image that do
not fit in the display are cropped
(removed).
video.screenModeFS
normal, full, crop
normal
The screen mode for the video window
shown in full screen mode. If set to
normal or Null, the entire view is
displayed and horizontal or vertical
black bars may appear on the edges to
maintain the correct aspect ratio. If set
to full, the entire view is stretched
linearly and independently to fill the
screen. If set to crop, black bars are
not shown, the image is re-sized and
enlarged to cover the entire screen,
and parts of the image that do not fit in
the display are cropped (removed).
voIpProt.H323.autoGateKeeper
Discovery
0 or 1
1
If set to 1, the phone will attempt to
discover an H.323 gatekeeper address
via the standard multicast technique,
provided that a statically configured
gatekeeper address is not available. If
set to 0, the phone will not send out
any gatekeeper discovery messages.
voIpProt.H323.blockFacility
OnStartH245
0 or 1
0
If set to 1, facility messages when
using H.245 are removed.
voIpProt.H323.dtmfViaSignal
ing.enabled
0 or 1
1
If set to 1, the phone will use the H.323
signaling channel for DTMF key press
transmission.
voIpProt.H323.dtmfViaSignal
ing.H245alphanumericMode
0 or 1
1
If set to 1, the phone will support H.245
signaling channel alphanumeric mode
DTMF transmission.
Note: If both alphanumeric and signal
modes can be used, the phone gives
priority to DTMF.
Polycom, Inc.
31
Polycom UC Software 4.1.5 Release Notes
Parameter
Permitted Values
Default
Description
voIpProt.H323.dtmfViaSignal
ing.H245signalMode
0 or 1
1
If set to 1, the phone will support H.245
signaling channel signal mode DTMF
transmission.
voIpProt.H323.enable
0 or 1
0
A flag to determine if the H.323
protocol is used for call routing, dial
plan, DTMF, and URL dialing. If set to
1, the H.323 protocol is used.
voIpProt.H323.local.port
1 to 65535
1720
Local port to be used for H.323
signaling. Local port for sending and
receiving H.323 signaling packets. If
set to 0, 1720 is used for the local port
but is not advertised in the H.323
signaling. If set to some other value,
that value is used for the local port and
is advertised in the H.323 signaling.
voIpProt.H323.local.RAS.port
1 to 65535
1719
Local port for RAS signaling.
voIpProt.server.H323.x.
address
dotted-decimal IP
address or
hostname
Null
Address of the H.323 gatekeeper.
Note: Only one H.323 gatekeeper per
phone is supported. If more than one is
configured, only the first is used.
voIpProt.server.H323.x.port
0 to 65535
1719
Port to be used for H.323 signaling.
Note: The H.323 gatekeeper RAS
signaling uses UDP, while the
H.225/245 signaling uses TCP.
voIpProt.server.H323.x.
expires
positive integer
3600
Desired registration period.
Understanding Updates to UC Software 4.1.2 Rev B
Polycom Unified Communications (UC) software 4.1.2 Rev B is a general release for the VVX 500 and
VVX 600 products with all supported SIP servers including Microsoft Lync Server 2010 and qualified
compatible Microsoft Lync Server 2013. For Microsoft Lync Server, this release supports a single
registered line.
Note: UC Software 4.1.x - New and Enhanced Features
Microsoft Lync users can refer to Understanding Updates to UC Software 4.1.0 Rev B for
information on new and enhanced features and capabilities available with Lync-compatible UC
software.
Polycom, Inc.
32
Polycom UC Software 4.1.5 Release Notes
This section lists all changes, additions, removals, enhancements, and configuration file parameter
changes to UC software 4.1.2 Rev B beside their respective Polycom tracking identification number.
New or Enhanced Features
82450 The phone now sends the SIP INVITE and REGISTER messages in the MS-Subnet header.
Enhanced Capabilities
81683 The phone now fetches the Location Information Service by using either NTLM credentials or the
Lync-signed user certificate.
83754 Restarting the phone after a network outage automatically registers and signs in the user.
83564 On the Russian SKUs, only the SIP signaling is encrypted during in-band provisioning, leaving
the media unencrypted.
84105 Frequent multiple Sign in- Sign out no longer causes any reboot on the phone.
84218 The phone no longer caches the call history of the previously signed user.
84221 The phone can now dial to a federated contact with a long URI from the quick dial list.
84298 The phone calls now comply with the enterprise Lync server bandwidth policy.
84305 The risk of accidentally dialing an emergency number in the locked state is reduced. The user
now has to select a number from the authorized contact list and press the send button to initiate a
call.
Understanding Updates to UC Software 4.1.2
Polycom Unified Communications (UC) software 4.1.2 is a general release for the VVX 500 and VVX 600
products with all supported SIP servers including Microsoft Lync Server 2010. For Microsoft Lync Server,
this release supports a single registered line.
Note: UC Software 4.1.X - New and Enhanced Features
Microsoft Lync users can refer to Understanding Updates to UC Software 4.1.0 Rev B for
information on new and enhanced features and capabilities available with Lync-compatible UC
software.
New or Enhanced Features
62651 Added Support for the Polycom VVX 600 product.
82042 Added support for BroadSoft Hoteling Event Package.
80220 Added support for Pin Authentication on MS Lync.
82162 Added support for Verizon (Baltimore CA 2048) certificate.
Polycom, Inc.
33
Polycom UC Software 4.1.5 Release Notes
Enhanced Capabilities
82101 The “mute” hard key and mute display on the phone while initiating a conference call are now
synchronized.
81878 On the phone’s virtual keyboard the input mode key will no longer overlap with other keys on the
screen.
81536 On the contact entry/edit screen, the default encoding “Abc” mode is changed to “abc” by
pressing the “Caps” key on the phone virtual keyboard.
80790 The phone no longer deregisters when trying to install an unknown certificate.
80761 When using Polycom Desktop Connector (PDC) the “Alt + numeric” keys are configured to off
hock the lines accordingly.
79968 Users can now scroll up/down in the phone voice recording menu while deleting recorded files.
79680 The phone displays a pop-up message when there is a low bandwidth detected while hosting a
centralized conference.
79625 When the phone tries to park a call using blind transfer and fails, the call is retained back
between the caller and called phone.
78256 In a Lync environment, contacts screen now displays 5 soft keys.
75808 When the phone is configured with one or more BLF lines, the first incoming call to the BLF lines
during prompt stage is displayed on main display and the second stacks on top.
74607 Soft key label is corrected as “select” under the unavailable reason codes in ACD menu.
73618 Changing the phone web UI language reflects on all the contents except ringtones.
72197 Clicking the “check for updates” button the phone web UI now populate all the available software
versions from the Polycom hosted server in the combo box.
72055 Enhanced the pop-up message to “Failed to fetch available software from the Polycom Hosted
server. Please try again later or contact your Network Administrator if the problem persists” when
trying to connect to the Polycom hosted server from the phone web UI.
64091 Resetting the local configuration on the phone will no longer reboot the phone.
Configuration File Enhancements
Refer to the following table for a list of all enhancements made to the UC software 4.1.2 configuration file
parameters.
Web Info: Understanding Polycom Configuration Parameters
You can find detailed descriptions of these parameters and their values in the Polycom UC Software
4.1.0 Administrators’ Guide on the support web site.
Polycom, Inc.
34
Polycom UC Software 4.1.5 Release Notes
Table 7: UC Software 4.1.2 Parameter Enhancements
File
Modification
Parameter
Modification Description
Feature
Added
reg.X.auth.usePinCredentials
“0” or “1” to enable or disable the
Pin authentication. This will be
disabled by default and enabled
when the Base Profile is set to
‘Lync’.
="0" or “1”
X= line, e.g.1,2,3, etc.
Feature
Added
reg.X.auth.useLoginCredentials="0"
or “1”
To enable or disable the login
credentials. The treatment of this
parameter has not changed by
the PIN Authentication Feature.
X= line, e.g.1,2,3, etc.
Feature
Added
reg.X.auth.loginCredentialType="user
nameAndPassword"
X= line, e.g.1,2,3, etc.
To enable the type of login
credentials.
Below are the available options:
1. loginCredentialNone
2. usernameAndPassword
3. extensionAndPIN
The default value is
loginCredentialNone.
Understanding Updates to UC Software 4.1.0 Rev B
®
®
Polycom UC software 4.1.0 Rev B is for use only with Microsoft Lync Server using a single registered
line.
UC software 4.1.0 Rev B supports the following Polycom devices:
 SoundPoint IP 321, 331, 335, 450, 550, 560, and 650 (The SoundPoint IP 670 is not supported.)
 SoundStation IP 5000 conference phones
 SoundStation Duo conference phones
 VVX 500 business media phone
Note: UC Software 4.1.0 Rev A with SpectraLink 84xx Series Wireless Handsets
If you are using SpectraLink 84xx series wireless handsets, you must use UC software 4.1.0 Rev A.
For limitations and enhancements to UC software 4.1.0 Rev B, see the section Understanding UC
Software 4.1.0 for the SpectraLink 84xx and VVX 500Understanding UC Software 4.1.0 for the
SpectraLink 84xx and VVX 500 in this document.
For further details about support for SpectraLink series, see SpectraLink 8400 Wireless Telephones
on the Polycom Support web site.
New or Enhanced Features
78286 Added support for enabling/disabling auto discovery per line
Polycom, Inc.
35
Polycom UC Software 4.1.5 Release Notes
74716 Add support for dialing by extension
Enhanced Capabilities
80554 When the phone language is set to any non-English language and locked, the language on the
phone is preserved even after a reboot.
80519 When a new user is added to an existing IM conversation on a PC client, the added user’s phone
does not ring anymore when there is a join request.
80144 On the private line, the phone remains quiet when the ring type is set to silent.
80081 Enable/disable of Polycom desktop connector (PDC) from the phone’s web user interface work as
per the design.
79955 The phone automatically installs the CA certificate and registers to Lync sever after reboot, when
the certificate is deleted from the phone menu.
79916 The line labels are now updating after performing update configuration on the phone.
79797 The message waiting indicator (MWI) no longer blinks after the user signs out of the phone.
79225 The phone logs out the non-default user automatically as per the set time in the automatic logout
parameter.
79070 Enabling login credentials of the user on the phone’s web user interface automatically disable the
user domain id/credentials on the phone.
77192 Adding a ‘+’ sign to the Line Identification address via the phone’s Web Configuration Utility is
now displayed correctly.
Configuration File Enhancements
For information on enhancements to UC software 4.1.0 Rev B configuration files, see Configuration File
Enhancements for UC software 4.1.0.
For details on all UC software 4.1.0 configuration files and parameters, refer to the Polycom UC Software
4.1.0 Administrators’ Guide on the Polycom PartnerConnect web site.
Understanding UC Software 4.1.0 for the SpectraLink 84xx
and VVX 500
Polycom UC software 4.1.0 (Rev A) was released to support only the SpectraLink 84xx series wireless
handsets and the VVX 500 business media phones. UC software 4.1.0 Rev B supports the VVX 500. If
you are using SpectraLink 84xx series wireless handsets, you must use UC software 4.1.0 Rev A. This
section explains enhanced features and capabilities of UC software 4.1.0 Rev A.
UC software 4.1.0 is a software upgrade for phones that are qualified to deliver direct interoperability for
Lync.
New or Enhanced Features
42163 Added support for simplified best-effort SRTP.
Polycom, Inc.
36
Polycom UC Software 4.1.5 Release Notes
66597 Added support for Microsoft STUN/TURN/ICE.
68649 Added support for Lync Certificate Provisioning using MS Web Ticket.
68652 Added support for Microsoft E911.
68653 Added support for Lync Call admission control.
68802 Added support for Lync In-band provisioning.
68803 Added support for Lync server address discovery.
68654 Added support for Lync Media bypass.
69089 Added support for Lync Private incoming line.
69094 Added support to switch over to local ring when early media fails.
69096 Added support for Lync dial plans.
69106 Added support for Branch office resiliency (BOR) feature.
70673 Added support for alternative call forwarding identities.
74216 Added support for video synchronization with Lync client.
74567 Added support for Microsoft Web Ticket Client Protocol.
74510 Added ability to route all outbound requests via Outbound Proxy Server with different callee and
caller URI domains.
74557 Added support for a manual configuration re-sync with the Lync provisioning server.
74616 Added support for extension-based dialing.
74894 Added ability to retrieve Lync server root certificate automatically using DHCP Option 43.
75141 Added Base profile menu option for easy out-of-the-box experience.
77281 Added support for Lync mode on phones (Lync Base profile).
Enhanced Capabilities
79321 Significant improvements made on the battery threshold levels (applies to SpectraLink 8400).
79063 The phone now updates the presence status information for all watched buddies (applies to VVX
500).
78107 The phone now displays a warning message upon reaching the maximum number of buddies.
78100 On the phone Presence - Idle timeout settings, changing the office hours timeout value will not
change the Off hours timeout value.
78087 When a call is made from a SpectraLink Wi-Fi phone, the receiving phone now displays the
complete number of the caller.
77089 In a Lync environment, any changes to the buddy presence state are now immediately reflected
on the presence icons and status.
76995 In a Lync environment, phone call list details are no longer uploaded to the provisioning server
when setting the configuration parameter feature.callList.enabled=”0” (applies to VVX
500).
Polycom, Inc.
37
Polycom UC Software 4.1.5 Release Notes
76981 The phone now displays call forwarding icon and forwards calls correctly when the function is
enabled from the phone web user interface.
76446 Calls to PSTN network now work correctly, even when Media Bypass is enabled on the PSTN
gateway.
76261 The phone password field for Lync configuration now remains empty when no password is set,
thereby allowing the user to set a new password.
76194 Incoming calls now first display as a pop-up before being minimized to call appearance/filter view
on the phone.
76028 The Polycom Desktop Connector (PDC) has been improved and now connects to the user’s
laptop/PC after installation.
75874 Only the internal headset ring tone is played on Jabra PRO 9450 headsets (applies to VVX 500).
75872 The phone ringer now functions correctly while user is attaching/detaching a USB headset during
an incoming call.
75743 Corrected the usage of a configured outbound proxy server address for Voice quality monitoring
feature on phones.
75715 Local directory can now save contacts searched from the phone’s corporate directory, even when
the local directory is disabled.
75694 Adding/removing a USB headset no longer affects phones configured with EHS headsets (Jabra,
Plantronics or Sennheiser).
75674 URL dialing is now possible between unregistered phones.
75643 “Call list display” now functions correctly when the configuration parameter
feature.callList.enabled="0".
75605 Contacts containing long information fields (first name, last name, etc.) in detail view now display
correctly on the phone.
75431 PTT and Paging feature has now been enhanced to user iLBC codec.
75355 Improved the synchronization of contacts and addition/deletion between the Lync MOC client on
PC and Phone IM.
75245 Buddy presence status is now updated when the phone is disconnected from network.
74901 When the lock feature is enabled, after a phone reboot, the emergency/authorized call list
displays when the user tries to place a call using the headset/speaker key.
74888 Host status display during a multiparty Lync conference call now functions correctly.
74175 When the phone presence state is set to Be Right Back, it no longer changes to Offline when the
phone is left idle for a long period of time.
73797 Caller details now display correctly for participants in a Lync consultative transfer call.
72518 On the Lync soft client, only mobile platforms are now categorized as mobile.
70723 The phone now fetches the correct available software from the Polycom provisioning server when
the parameter upgrade.plcm.server.url is set correctly.
57864 Changes to SRTP parameters now take effect immediately, without rebooting the phone.
Polycom, Inc.
38
Polycom UC Software 4.1.5 Release Notes
Configuration File Enhancements
Refer to the following table for a list of all enhancements made to the UC software 4.1.0 configuration file
parameters.
Web Info: Find Detailed Descriptions of Parameters and Values
You can find detailed descriptions of these parameters and their values in the Polycom UC Software
4.1.0 Administrators’ Guide on the Polycom PartnerConnect web site.
Table 8: UC Software 4.1.0 Parameter Enhancements
File
Modification
Parameter
feature
Added
apps.telNotification.appInitializationEvent
feature
Added
apps.telNotification.networkUpEvent
feature
Added
apps.telNotification.uiInitializationEvent
feature
Added
apps.telNotification.taInitializationEvent
feature
Added
apps.telNotification.uiInitializationEvent
feature
Added
device.baseProfile device.baseProfile.set
feature
Added
dialplan.applyToForward
feature
Added
dialplan.x.applyToForward
feature
Added
locInfo.x.A1
feature
Added
locInfo.x.A3
feature
Added
locInfo.x.country
feature
Added
locInfo.x.HNO
feature
Added
locInfo.x.HNS
feature
Added
locInfo.x.label
feature
Added
locInfo.x.LOC
feature
Added
locInfo.x.NAM
feature
Added
locInfo.x.PC
feature
Added
locInfo.x.POD
feature
Added
locInfo.x.PRD
feature
Added
locInfo.x.RD
Polycom, Inc.
39
Polycom UC Software 4.1.5 Release Notes
File
Modification
Parameter
feature
Added
locInfo.x.STS
feature
Added
log.level.change.afe
feature
Added
log.level.change.ice
feature
Added
log.level.change.loc
feature
Added
log.level.change.tickt
feature
Added
log.level.change.xml
feature
Added
np.custom1.ringing.privateLine.tonePattern
feature
Added
np.custom1.ringing.privateLine.vibration
feature
Added
np.meeting.ringing.privateLine.tonePattern
feature
Added
np.meeting.ringing.privateLine.vibration
feature
Added
np.normal.ringing.privateLine.tonePattern
feature
Added
np.normal.ringing.privateLine.vibration
feature
Added
np.silent.ringing.privateLine.tonePattern
feature
Added
np.silent.ringing.privateLine.vibration
feature
Added
prov.login.lcCache.domain
feature
Added
prov.login.lcCache.user
feature
Added
reg.x.dialPlanName
feature
Added
reg.x.lisdisclaimer
feature
Added
reg.x.lync.autoProvisionCertLocation
feature
Added
reg.x.ringType.privateLine
feature
Added
reg.x.serverAutoDiscovery
feature
Added
reg.x.srtp.simplifiedBestEffort
feature
Added
sec.srtp.simplifiedBestEffort
feature
Added
softkey.feature.simplifiedSignIn
feature
Added
tcpIpApp.ice.mode
feature
Added
tcpIpApp.ice.password
feature
Added
tcpIpApp.ice.realm
feature
Added
tcpIpApp.ice.username
Polycom, Inc.
40
Polycom UC Software 4.1.5 Release Notes
File
Modification
Parameter
feature
Added
tcpIpApp.ice.stun.passwordServer
feature
Added
tcpIpApp.ice.stun.server
feature
Added
tcpIpApp.ice.stun.udpPort
feature
Added
tcpIpApp.ice.tcp.enabled
feature
Added
tcpIpApp.ice.turn.server
feature
Added
tcpIpApp.ice.turn.tcpPort
feature
Added
tcpIpApp.ice.turn.udpPort
feature
Added
voice.page.handsfree.rxag
feature
Added
voice.ptt.handsfree.rxag
Understanding Updates to UC Software 4.0.2 Rev B
This section details updates to UC software 4.0.2 Rev B.
New or Enhanced Features
72403 Added support for DHCP renews after loss and recovery of Wi-Fi LAN connection (applies to
SpectraLink 8400).
76730 Enhanced the digitmap by removing the prepending ‘+’ to the outbound calls and giving the
option of configuring the ‘+’ in the dial plan (applies to Lync mode only).
77038 Added support for early media followed by local ringback.
Enhanced Capabilities
73667 The syslog counter on the SpectraLink 8400 phones are updated accordingly when audio packets
are received.
75557 On the web interface of the phone, the logging module parameter Wi-Fi Manager log value is
updated in the field help section when the mouse is over parameter name as well as its value as
(applies to SpectraLink 8400).
76057 When a phone is registered with a single shared line, the Join soft key is no longer displayed
inappropriately when the monitored phone puts the call on hold.
76084 In a shared BLF line scenario, the monitoring phone no longer resumes the call from the
monitored phone without playing any busy tone.
76095 In a shared BLF line scenario, phone now displays the incoming call status of the monitored
phone (applies to VVX 500).
Polycom, Inc.
41
Polycom UC Software 4.1.5 Release Notes
76131 The phone default call appearance eliminates the display of remote on hold calls (applies to VVX
500).
76321/76515 The phone does not reboot when multiple URI’s are pushed to the phone in frequent
intervals. (Customer issue ID VESC-1635, VESC-1650).
76427 The phone displays only the incoming call received from a line that is also being monitored using
BLF (used to display this as two calls in the list) (applies to VVX 500).
76467 Improved Call list display for caller ID with long names (applies to VVX 1500).
76591 The phones display the correct Asian language fonts for the Lync contacts.
76679 Unauthorized request for configuration files using phone web interface is now restricted.
76754 The Filtered call view of a BLF monitored line is shown properly when the phone is in off-hook
state.
76862 During an active BLF call session, frequent pressing of the BLF key on the origination phone no
longer causes the caller ID information to be blanked out.
76889 The PPT key can now be configured as a Speed dial key on the SpectraLink 8400 phones.
76911 The dialer screen UI on the phone is refreshed when an incoming ringing call is terminated.
76934 On-hook dialing work as expected when the phone has an incoming call and the remote party
ends the call.
76939 The phone highlights the last incoming call as per the order in call appearance screen (applies to
VVX 500).
76940 Incorrect soft key options no longer displayed on the BLF monitoring phone when there is an
incoming call in certain scenarios.
76944 Auto Answer now works correctly when alert information header carrying the string within the
angle brackets ‘< >’ is received.
76946 The phone current draw is optimized as per its state (applies to SpectraLink 8400).
76947 The audio/ sound effect termination is always on the dock station when there is an active call on
the phone (applies to SpectraLink 8400).
76949 The browser application on the phone times out as expected (applies to SpectraLink 8400).
76976 The phone no longer inadvertently goes off-hook on line1 instead of line2 when the user presses
the second line key while lifting the handset with call hold on line1.
77099 Manual configuration of the IP address no longer causes a ‘network is down’ message to be
displayed (applies to SoundStation IP 6000, 7000).
77135 Addressed some Directed call pickup failures in certain situations.
77173 Turning the backlight OFF on the phone no longer sends the browser to the session list (applies
to SpectraLink 8400).
77226 When the phone is registered to a Lync line and another call server, the Lync contact presence
subscription is now correctly sent through the Lync registered line.
77363 Addressed the issue that could cause a reboot when the user has many buddy contacts
configured (applies to VVX 500). (Customer issue ID VESC-1763)
Polycom, Inc.
42
Polycom UC Software 4.1.5 Release Notes
77396 Addressed a phone reboot issue in a certain ACD/call center configuration (Found in UC software
3.3.2).
77549 Addressed an issue relating to use of the ‘Join’ key which was displayed even when only one call
was in progress (applies to SoundPoint IP 33x, SoundStation Duo and SpectraLink 8400
models).
77626 Two way audio between the phones is now working as expected after resuming the call from
MOH when voIpProt.SIP.musicOnHold.uri or reg.X.musicOnHold.uri is used for the
address of the MoH server.
77749 The registration failing issue with Lync server front end due to error in Subject Alternative Name
(SAN) validation implementation is addressed.
77830 Addressed an issue where when the phone is configured with certain languages options,
attempting to select LLDP or CDP using Ethernet caused a reboot (applies to SoundStation IP
6000).
Configuration File Enhancements
Refer to the following table for a list of all enhancements made to the UC software 4.0.2 Rev B
configuration file parameters.
Table 9: UC Software 4.0.2 Rev B Parameter Enhancements
File
Modification
Parameter
Modification Description
Wireless
Added
device.dhcp.releaseOnLinkRecovery
1 Phone performs a DHCP
release on network link recovery
(Default)
0 Phone does NOT perform a
DHCP release on network link
Note: Also refer to configuration parameter changes in UC software 4.0.2.
Note: Ensuring Digitmap Compatibility between UC Software Versions 4.0.1 and 4.0.2 Rev B
The existing digitmap dialplan.digitmap = [2-9]11|0T|011xxx.T|[0-1][29]xxxxxxxxx|[2-9]xxxxxxxxx|[2-9]xxxT in the UC software 4.0.1 release where the phones
were automatically pre-pending a + to outbound calls is now removed in UC software 4.0.2 Rev B.
For UC software 4.0.2 Rev B to be backwards compatible to UC software 4.0.1, the digitmap should
be dialplan.digitmap=RR+R[2-9]11|0T|RR+R011xxx.T|RR+R[0-1][29]xxxxxxxxx|RR+R[2-9]xxxxxxxxx|RR+R[2-9]xxxT, or if the digitmap is to apply for a
certain line, use dialplan.1.digitmap=RR+R[2-9]11|0T|RR+R011xxx.T|RR+R[0-1][29]xxxxxxxxx|RR+R[2-9]xxxxxxxxx|RR+R[2-9]xxxT.
Understanding Updates to UC Software 4.0.2 (Limited
Release)
Polycom, Inc.
43
Polycom UC Software 4.1.5 Release Notes
This section lists the additions, changes, removals, enhancements and configuration file parameter
changes to UC software 4.0.2.
Note: UC software 4.0.2 is a limited release that was distributed only to select partners and customers
and is shipping with SoundStation Duo. The build-ID for this release was UC software 4.0.2.8017.
New or Enhanced Features
40451/75448
Added support for XT9 PinYin input for Chinese characters (applies to VVX 1500).
52485/66494
Added support for BroadSoft Hoteling Event Package.
57167/66494/76023 Added support for BroadSoft Call Center Status Event Package.
54576 Added support for the new SpectraLink 8452 Wi-Fi handset with 2D barcode reader.
Enhanced Capabilities
69469 The display name with special character < or > causes phones to respond with a bad request.
73614 An unintentional touch on the phone initiates a call automatically (applies to VVX 500).
73946 On the Trapeze/Juniper infrastructure, when multiple SpectraLink phones are involved in a call,
one or more phones may lose wireless connectivity.
74292 The Bluetooth radio can now be activated on SpectraLink 8400 phones.
74427 On a redirected call, the phone now sends a PRACK (acknowledgement) message.
75299 The dialpad key presses are now captured when hot dialing from the idle browser screen (applies
to VVX 500).
75419 The ADHOC conference call now works when there is a + sign, for example,
(SIP:voip+world@voipworld.com) in the Sip URI contact header.
75632 Slowness in dialing with large number of contacts on the phone is resolved (applies to VVX 500).
75686 The up and down arrow keys are now available on the phone during call transfer (applies to
SoundPoint IP 450.)
75726/75716 The phone numbers dialed using the auto complete remembers the line info on which the
calls are placed earlier (applies to SpectraLink 8400, VVX 500 and VVX 1500).
75811 Reassigning the line keys preserves the presence information.
75888 A scrolling status message is now displayed when a line is unregistered on the phone.
75945 When the phone is off hook, auto dialing remember the line information (applies to SpectraLink
8400, VVX 500 and VVX 1500).
75954 The overlap of idle browser on the call list screen is now set (applies to VVX 1500).
75949/76258 The SoundStation Duo phone complies with clause 5.5.1.4.1 of Australian spec S002 of
the Australian analog telephony specification as per clause 5.5.1.4.1 of Australian spec S002.
76141 The call lists on the VVX 1500 phone get updated as required.
76171 The phone no longer continuously reboots on reassignment of the line keys.
Polycom, Inc.
44
Polycom UC Software 4.1.5 Release Notes
76229 A break down observed on the phone monitoring a BLF contact is now fixed. (Customer issue ID
VESC-1670)
76315 The pop-up message Error Line: Unregistered will no longer appear as a result of an absence of
a register request.
76316 The default hookflash timing is set on the SoundStation Duo when the country is set to Australia.
76329 Soft keys on the VVX 500 are now responsive to touch.
76376 An unregistered pop-up no longer appears the on SoundStation Duo in PSTN mode.
76379 Double quotes appended to the calling party display name on a shared line are now removed.
76408 Shared lines will continue to ring when another phone with the same shared line answers an
incoming call on another line appearance.
76420 After reboot, the phone will correctly display incoming calls of a monitored BLF contact even on
the first call.
76422 All the incoming call appearances on a BLF monitored phone are displayed when the monitoring
phone cancels the call to the BLF contact.
76423 In a BLF monitored scenario, multiple calls to a monitored phone display the incoming call
appearance and call counter appropriately.
76428 The phone will properly display incoming call appearance after terminating a call on phone using
the End Call soft key.
76535 The phone will now correctly display a warning icon and a pop-up message for unregistered
H.323 lines. (applies to VVX 1500)
76600 The blank call appearance on the monitoring BLF enabled phone is set.
76601/76685 In a multi-party BLF enabled call, the widget displaying the call appearance, counter,
icons, and the indicator is updated with the appropriate incoming and outgoing call status.
76690 The phone now functions normally with the call appearance of the monitored BLF contacts.
76694 The phone will no longer crash when a monitored line ends the call that is associated with the
remote call appearance screen.
76838 On a PSTN line the invocation of redial is restricted by pressing the # key after entering the digits
(applies to SoundStation Duo).
76849 On a PSTN line pressing the # key is now restricted to send the dialed number only once (applies
to SoundStation Duo).
76875 The phone now picks up the call forwarding settings from the override file after a reboot.
Configuration File Enhancements
Refer to the following table for a list of new parameters. Note that these configuration parameters are
detailed in Feature Profile 76179: Hoteling and ACD, which will be made available on Polycom Profiled
UC Software Features.
Polycom, Inc.
45
Polycom UC Software 4.1.5 Release Notes
Table 10: UC Software 4.0.2 Parameter Enhancements
File
Modification
Parameter
Modification Description
feature
Added
feature.callCenterStatus.enabled
Call feature parameter
feature
Added
feature.hoteling.enabled
Call feature parameter
feature
Added
hoteling.reg
Call feature parameters
wireless
Added
barcode.X.Y
Parameters used to configure
the 2D barcode scanner*
*For a detailed description of new parameters specific to the SpectraLink 8400 product family, their properties and
values, refer to the Polycom SpectraLink 8400 Series Wireless Telephone Deployment Guide.
Understanding Updates to UC Software 4.0.1B
There are no functional differences between Polycom UC software 4.0.1B and Polycom UC software
4.0.1. Polycom UC software 4.0.1B was released to include the VVX 500 and SoundStructure sip.ld files
in the software release package.
Understanding Updates to UC Software 4.0.1
This section lists additions and changes, removals, enhancements, and configuration file parameter
changes to the UC software 4.0.1 beside their respective Polycom tracking identification number.
New or Enhanced Features
48734 In a server-based, centralized conference, the phone can now send parallel REFERs without
waiting for a 202 Accepted.
67081/70634 Added support for phones to interoperate with a limited set of Microsoft® Lync™ server
features (applies to SoundPoint IP 321, 331, 335, 450, 550, 560, 650, 670, VVX 500, 1500,
SoundStation IP 5000, SoundStation Duo, and SpectraLink 84xx).
67090 Syslog now includes the ability to identify multiple audio streams (applies to SpectraLink 84xx).
67594 Added interoperability between the Message Waiting Indicator (MWI) and Microsoft Lync.
68500 The SpectraLink 84xx handsets now display the X-Loader version information in the Phone menu
(Menu > Settings > Status > Platform > Phone).
68602 Added support for SSRTP.
68798 Added support for Microsoft SRTP extensions.
69962/70924 Added Microsoft OCS/Lync Presence functionality to phones (applies to SoundPoint IP
321, 331, 335, 450, 550, 560, 650, 670, VVX 500, 1500, SoundStation IP 5000, SoundStation
Duo, and SpectraLink 84xx).
Polycom, Inc.
46
Polycom UC Software 4.1.5 Release Notes
70122 The phones now display the Away presence status after a period of user inactivity specified by
the following parameters: pres.idleTimeout.offHours.period,
pres.idleTimeout.officeHours.period, pres.idleTimeout.offHours.enabled,
and pres.idleTimeout.officeHours.enabled.
70232 Added a parameter call.transfer.blindPreferred to control whether the Transfer soft
key on the SpectraLink 84xx should be a consultative transfer or blind transfer.
70614 Added support for Microsoft 2008 Radius (802.1X).
71025 Added new per-registration configuration options for several SRTP parameters:
reg.x.srtp.enable, reg.x.srtp.offer, reg.x.srtp.require.
71183 Added missing barcode symbologies (applies to SpectraLink 84xx).
71198 Added an option in the Web Configuration Utility for SIP and Provisioning TLS applications to
make the Common Name of Subject test configurable.
71424 Updated the presence icon on the phones to be consistent with the Microsoft Lync/OCS style
(applies to SpectraLink 84xx).
71439 Not including the parameter oai.userID in the configuration file or setting the value to NULL
both result in the phone using its MAC address to check in into the OAI server (applies to
SpectraLink 84xx).
71660 Enhanced the Reset to Default option in the Updater to match the option in the application
software.
71774 The call forward status on the status bar now displays when Forward – No Answer or Forward –
Busy is enabled (applies to SpectraLink 84xx).
71997 Added full support for RFC2782 (DNS load balancing).
72074 In the Web Configuration Utility, the Country Code field has been renamed to Regulatory Domain
(applies to SpectraLink 84xx).
72193 In the phone menu, the Country Code field has been renamed to Regulatory Domain (applies to
SpectraLink 84xx).
72279 Enabled an EFK to allow a user to invoke the Call Back feature while on hook (applies to VVX
1500).
72304 The default value for the configuration parameter up.useDirectoryNames is now 1 (enabled).
72310/74129 The SpectraLink series handsets can now display the BootL1 version information in
Phone menu (Menu > Status > Platform > Phone).
72319 The phone displays a warning icon when the WLAN Network Manager detects an invalid
Regulatory Domain request (applies to SpectraLink 84xx).
72320 The phone displays a warning triangle when the WLAN Network Manager detects an invalid
Regulatory Domain limit setting (applies to SpectraLink 84xx).
72367 The phone automatically publishes an Inactive (Idle) presence status after 5 minutes of user
inactivity.
72554 Added the ability to configure the pres.idleTimeout parameters through the phone menus.
Polycom, Inc.
47
Polycom UC Software 4.1.5 Release Notes
72555 Added the ability to configure the pres.idleTimeout parameters through the Web
Configuration Utility.
72654 The Exchange Calendaring feature on the SpectraLink handsets has been improved with the
following enhancements:

The Calendar icon is shown in the main menu once the calendar is authorized.

The phone displays a Calendar: synchronizing scrolling message in the status bar.
72791 The microbrowser on the SoundPoint phones has been functionally improved with the following
enhancements:

The audio tag element will inject a Play soft key when in focus.

The user can now specify additional attributes to the audio tag which will be interpreted as a
soft key, thus allowing the user to do things such as a Details soft key.

The audio tag will have a descriptive label which will be used as the button label for the audio
element in the page. This enables each audio tag to be rendered as a single element in the
page with an icon and a descriptive text. The user no longer needs to switch to the text to see
the details.

The descriptive label will also be used for the title of the playback screen.
72823 In the media player, the Exit soft key has been renamed to Back.
72824 Playback automatically starts when selecting an audio element from the browser.
73420 When the phone language is set to Japanese, the phone now uses the English AM/PM string for
the time/date display (applies to all SoundPoint IP, all SoundStation IP, and SoundStation Duo).
73500 The ‘Connect/disconnect from the server’ option has been moved to the Calendar menu
(Features > Calendar) in the SpectraLink 84xx handsets.
73510 The Web Configuration Utility language now supports multiple default language labels and help
text in English, with the option to add/access other languages.
73669 Updated the 2048-bit Trusted CA Root Certificate List from VeriSign.
73670 Added new VeriSign Intermediate CA certificates.
73671 Added RSA 2048 V3 Root Certificate to Root Store to all phones.
73805 The phone can now display up to 4 Chinese characters in the soft keys (applies to SoundPoint IP
450).
73907/74289 Added the ability to automatically upgrade the BootL1 and BootBlock (applies to
SpectraLink 84xx).
74247 In the Web Configuration Utility, the default available utility languages depend on the platform.
74417 The Updater (BootROM) now supports Basic Authentication with HTTP/HTTPS.
75308 Added the ability to upload encrypted call lists to the provisioning server (applies to SpectraLink
84xx).
75469 The volume of PTT audio has been increased and setting the parameter
voice.handsfree.rxag.SL8440=10, then updating the phone using Update Configuration
does not cause the phone to restart (applies to SpectraLink 84xx).
Polycom, Inc.
48
Polycom UC Software 4.1.5 Release Notes
Enhanced Capabilities
55237 Dialing a semicolon using on-hook dialing no longer displays the off-hook dialing dialog (applies
to VVX 1500).
61038 The phone no longer becomes unresponsive to hard key and touch screen presses for several
seconds (applies to VVX 1500 phones provisioned with CMA using UC software 3.3.1).
66864 Using a dial plan containing #, when a user dials #1#2#, the phone now sends out an invite
message containing %231%232%23 (applies to SoundStation Duo).
68356 The phones can now fragment packets when instructed to by an ICMP message (applies to
SoundStation IP 6000 and 7000).
68501 When using Exchange Calendaring, the passcode now enters automatically (applies to
SpectraLink 84xx).
68835 The phone can now properly sniff EAP type frames (applies to VVX 1500).
69020 SoundPoint IP phones capable of downloadable fonts now correctly display certain Czech
characters.
69540 A call dropped by the other party no longer displays as a held call.
69558 An Avaya 10x0 and a VVX 1500 can successfully establish a video call.
69882 In PSTN only mode, a received call is now recorded in the Received Calls call list when the call is
finished (applies to SoundStation Duo).
69883 In PSTN only mode, an incoming call is now recorded in the Missed Calls call list when the call is
not answered (applies to SoundStation Duo).
70228 The phone no longer reboots when attempting a conference using an SCA line (applies to
SoundPoint 321, 331).
70542 The registered line icon and BLF icon are no longer corrupted in the SpectraLink 84xx handsets.
70944 A dialed number no longer overwrites a registered line’s label if the label is very long (all
SoundStation phones).
71041 The phones can now play audio from the Lync voicemail system (applies to SpectraLink 84xx).
71348 Calls between a VVX and RMX no longer cause the VVX to crash and reboot.
71368 Remote shared line activity no longer affects local phone presence.
71433 The phones crash after loading se.pat.callProg.dialTone parameters and pressing the
New Call button (applies to SoundPoint IP 450, 650, and SpectraLink 84xx).
71604 The configuration parameter sec.TLS.SIP.strictCertCommonNameValidation can be
updated without requiring a phone reboot.
71616 The conference feature can now properly handle a 480 response to a BroadSoft SCA line seize
SUBSCRIBE.
71763 The phone no longer sends a re-INVITE to the conference server after sending a REFER for
each leg of the conference (applies to SoundPoint 321, 331).
71764 Sennheiser and Jabra headsets can now go off-hook after switching to a different headset type
(applies to SoundPoint IP 335, 450, 550, 650).
Polycom, Inc.
49
Polycom UC Software 4.1.5 Release Notes
71802 Warning icons and records are now removed after the error condition is removed (applies to all
SoundPoint IP).
71829 An EFK has been created to display the corporate directory Advanced Find menu from the idle
screen (applies to VVX 1500).
71910 The text ‘Enter password’ in the Advanced menu is now translated when switching phone
languages.
72113 The Polycom Quick Barcode Connector icon now appears and disappears for both multiple and
single endpoint modes (applies to SpectraLink 84xx).
72250 The phone no longer reboots when queued messages are accessed on the phone (applies to
SpectraLink 84xx).
72368 URL Dialing from the call list is now fully disabled when feature.urlDialing.enabled=0
(applies to SpectraLink 84xx).
72442 The SoundPoint IP 321 and 331 phones now display the correct call x/y widget when
filterReflectedBlaDialogs=0.
72298 The Join soft key is no longer missing after establishing the maximum number of calls on all the
lines using when using a Sylantro call server (applies to SoundPoint IP 650 and VVX 1500).
72469 When feature.urlDialing.enabled is set to 0, the phone accepts contact entries with a
contact number longer than 10 digits (applies to SpectraLink 84xx).
72739 The phones can now play the audio files using the microbrowser (applies to all SoundStation
phones).
72800 Lines registered to a Microsoft Lync 2010 server now display in the Ring Type menu (Menu >
Settings > Basic > Ring Type).
72820 The VVX 1500 phone can be registered with up to 29 lines, but a max of 24 can be displayed.
72822 The phone no longer gets into a bad state (which required an auto-reboot) upon receiving two
consecutive 401 to a line-seize SUBSCRIBE during conference initiation.
72837 The speed dial icon no longer disappears after a Reset Local Config or Reset Web Config option
is selected (applies to SoundPoint IP 321, 331, 331C, 335, 335C).
72895 The phone override file is no longer created on the provisioning server when values are not
changed through the phone (applies to VVX 1500).
72907 Improved the phone’s conference call management when a cell phone is connected to the 2.5mm
port (applies to SoundStation Duo and SoundStation IP 7000).
72961 Bellcore Caller ID detection in PSTN mode works reliably now (applies to SoundStation Duo).
72996 A conference call between three parties now successfully connect all parties after there is a no
response to line seize SUBSCRIBE.
73027 A Plantronics Savi740 EHS headset no longer has intermittent pairing issues with a VVX 1500.
73054 Call appearances are now displayed correctly when pressing the New Call soft key while there is
an incoming call (applies to SoundStation Duo).
73084 Key in Keypad Diagnostics menu is now translated on SoundPoint IP 321, 331, and 335 phones
for all languages.
Polycom, Inc.
50
Polycom UC Software 4.1.5 Release Notes
73145 Regulatory Domain Error when radio set to 802.11a and band1 is set to P6 (applies to
SpectraLink 84xx).
73153 Hot dial window now disappears after auto answering a call (applies to SoundPoint IP 450, 650).
73183 The phone now displays the error message ‘Network link is down’ when the DHCP server is down
(applies to SoundPoint IP 335, 450, 560, 670).
73195 The bootloader menu for WEP has the correct spelling of Encryption (applies to SpectraLink
84xx).
73227 The phone UI now displays the proper network parameters such as IP address, subnet mask,
and IP gateway when DHCP is enabled (applies to SoundStation Duo).
73238 Changing the options in the directory search, then logging into the phone no longer causes the
phone to restart (applies to SoundPoint IP 321, 331, 331C, 335, 335C).
73247/74912
In the Quick Setup menu, user entry fields are now set to numeric as default.
73259 Simultaneous incoming and monitored BLF calls are now both displayed on the unified call
appearance list (applies to SoundPoint IP 450, 550, 560, 650, 670).
73263 Ending a PTT or page no longer causes the active call appearance to disappear for 10 seconds
(applies to SoundPoint IP 450, 550, 560, 650, 670).
73264 A phantom call appearance no longer displays when there is an active BLF monitored call and
the phone has another call appearance.
73290 The User Profiles Log In soft key is no longer missing when the feature presence is enabled
(applies to SoundPoint IP 670).
73401/74688 With intercom configured, the handset now rings once and incoming calls are answered
automatically (applies to SpectraLink 84xx).
73405 The Missed Calls list no longer displays on a peer shared line if the call was barged in from a
remote shared line (applies to SoundPoint IP 321, 331, and 335).
73409 In the Web Configuration Utility, all instances of the text ‘extension module’ have been replaced
with ‘expansion module’.
73419 When the IP 670 is configured for 34 lines using three expansion modules, a large contact
directory, LDAP, idle browser, and a microbrowser, it no longer crashes due to a lack of memory.
73459 The User Profiles feature is now fully supported on the SoundStation Duo.
73527 If barge-in is enabled on a shared line, remote active calls will not appear.
73561 When using the Web Configuration Utility, the phone now updates the line key icons properly
when static BLF is configured (applies to SoundPoint IP 450, 550, and 650).
73697 The flash timing is now correct for France and Singapore (applies to SoundStation Duo).
73749 Plugging in (or in and out) a 2.5mm mobile phone or PC cable no longer causes the phone to
reboot (applies to SoundStation Duo).
73910 The phone’s LCD contrast no longer turns darker after upgrading to UC software 4.0.0 (applies to
SoundPoint IP 450).
74018 The phone no longer locks up and reboots when there are a large number of incoming calls
(applies to SoundPoint IP 650).
Polycom, Inc.
51
Polycom UC Software 4.1.5 Release Notes
74045 The phone can now boot up to the idle screen properly after being issued a check sync to enable
the paging feature soft key.
74050 The phone no longer segfaults on boot due to language dictionary files (applies to all SoundPoint
IP).
74060 OAI PT Select Connections are now accepted by phone before an OAI call is answered by the
Start key (applies to SpectraLink 84xx).
74167 In the Web Configuration Utility, the authentication password can no longer be seen in clear text
when opening the line page source code.
74259 In PSTN mode, the phone now displays the date and time information on the idle screen after a
reboot (applies to SoundStation Duo).
74431 The phone no longer generates a beep sound when a monitored user goes off-hook (applies to
SoundPoint 650).
74956 The phone will no longer go into an INVITE loop and reboot if it receives a 503 response to its
initial INVITE message (applies to all SoundPoint IP).
74991 A call between a VVX 1500 and CX series phone can now be properly resumed after it has been
held for longer than 30 seconds.
75151 Audio files are now directly downloaded to the ramdisk.
75194 The phones now use an outbound proxy when an outgoing call’s URI domain is different from the
caller’s domain.
75334 Fail over on a 503 response can now be disabled.
75458 The maximum values for the DNS TTL parameters in the static cache have changed to
2147483647.
75485 The default input type for the Unavailable Code field is now numeric.
75491 Ampersand characters are now escaped properly and are no longer being stripped off of a URL
(applies to VVX 500, 1500).
75743 The Voice Quality monitoring feature now uses an outbound proxy server address for a SIP
Publish.
75600 The call appearance for an outgoing call no longer displays the transport string.
75618 Users can now place a call from the Placed Calls call list when the original call was placed using
a Click-To-Dial Refer message with Refer-To: header as sip:number ext. number @IPaddress;
transport=TCP (applies to SpectraLink 84xx).
Configuration File Enhancements
Refer to the following table for a list of enhancements made to the UC software 4.0.1 configuration file
parameters.
Polycom, Inc.
52
Polycom UC Software 4.1.5 Release Notes
Web Info: Parameters Changed in UC Software 4.0.1
The following table includes parameters modified in UC software 4.0.1. You can find detailed
descriptions of the parameters and their values in the Polycom UC Software 4.0.1 Administrators’
Guide.
Table 11: UC Software 4.0.1 Parameter Enhancements
File
Modification
Parameter
Modification Description
sip-interop
Added
call.transfer.blindPreferred
Call feature parameter
debug
Added
feature.lyncDebug
Call feature parameter
site
Added
reg.x.srtp.enable
Call feature parameters
reg.x.srtp.offer
reg.x.srtp.require
wireless
Added
np.custom1.ringing.toneVolume.us
bHeadset
Notification profiles parameter
wireless
Added
np.meeting.ringing.toneVolume.us
bHeadset
Notification profiles parameter
wireless
Added
np.normal.ringing.toneVolume.
Notification profiles parameter
usbHeadset
wireless
Added
np.silent.ringing.toneVolume.
Notification profiles parameter
usbHeadset
site
Added
sec.encryption.upload.
Security parameter
callLists
sip-interop
Added
sec.srtp.mki.length
Security parameter
sip-interop
Added
sec.srtp.padRtpToFourByte
Security parameter
Alignment
reg-advanced,
site
Added
up.headset.phoneVolumeControl
User preferences parameter
debug
Added
up.headset.AlwaysUseIntrinsic
User preferences parameter
Ringer
reg-advanced,
site
Added
up.idleStateView
User preferences parameter
video
Added
video.iFrame.delay
Video parameter
debug
Added
video.iFrame.period
Video parameter
techsupport
Added
voice.usb.headset.rxdg
Audio parameter
Polycom, Inc.
53
Polycom UC Software 4.1.5 Release Notes
File
Modification
Parameter
Modification Description
techsupport
Added
voice.usb.headset.txdg
Audio parameter
site
Added
voice.volume.persist.usb
Audio parameter
Headset
sip-interop
Added
voIpProt.SIP.conference.
Call feature parameter
parallelRefer
site
Added
webutility.language.plcm
ServerUrl
Web Configuration Utility
parameter
techsupport
Removed
voice.gain.rx.digital.headset.IP
_330
Audio parameter
techsupport
Removed
voice.gain.rx.digital.headset.IP
_335
Audio parameter
site
Changed
dns.cache.NAPTR.x.ttl
The maximum value increased
from 65535 to 2147483647
dns.cache.SRV.x.ttl
dns.cache.A.x.ttl
reg-advanced,
site
Changed
up.useDirectoryNames
The default value changed from
0 (disabled) to 1 (enabled).
pstn
Changed
up.operMode
The default value changed from
0 to auto.
techsupport
Changed
voice.headset.rxag.adjust.
The default value changed from
-11 to 4 and the maximum
value changed from -11 to 90.
IP_335
techsupport
Changed
voice.headset.rxag.adjust.
IP_330
sip-interop
Changed
VoIpProt.SIP.failoverOn503
Response
The default value changed from
-5 to 4 and the maximum value
changed from -5 back to 90.
The default value changed from
1 (enabled) to 0 (disabled).
Understanding Updates to UC Software 4.0.0
This section lists additions and changes, removals, enhancements, and configuration file parameter
changes to UC software 4.0.0 beside their respective Polycom tracking identification number.
New or Enhanced Features
26549 Enhanced the local missed call feature for shared line appearances. This feature supports RFC
3326 Reason Header.
28514 Enhanced the method of selecting a ring type on the menu screen.
Polycom, Inc.
54
Polycom UC Software 4.1.5 Release Notes
29056 Enhanced the method of notifying the user of unregistered lines.
30251 Added support for non-volatile call lists (applies to SpectraLink 84xx).
30887 Added support for 802.1X authentication. Authentication methods include MD-5, EAP-PEAP,
EAP-FAST, EAP-TLS, and EAP-TTLS.
32169 The user is now notified with a confirmation when deleting contact information.
33546 Added a host name field to the DHCP registration.
35170 Added support for User Profiles. Users may log into and out of the phone using a serverindependent, configuration file-based, authentication method. When successfully authenticated,
the user’s personal configuration files are applied as well as the user’s personal local contact
directory and call lists.
35171 Updated most configuration parameters to be updated without the need of a reboot. Only a select
number of configuration parameters require a reboot in order to be invoked.
36166 Added the option for the user to allow ringer volume levels to persist after the phone reboots.
38201 The Web-based configuration utility no longer requires the user to submit changes along with a
reboot after each page has been modified.
41429 Added the ability in the microbrowser to manage allowable characters into the input field.
41430 Added the ability in the microbrowser for the user to select an item from a list using the dial-pad.
44258 Enhanced the API by enhancing the HTTP Push capability by supporting mutual TLS.
44699 Added a Reset to Factory capability.
45777 Added user accessible diagnostic functions ping and traceroute.
47730 The scrolling status bar has been enhanced. The time between scrolled lines has been increased
(applies to SoundPoint IP 3xx).
47766 The Trusted CA Pool Management capability has been enhanced. The number of supported
customer certificates has been increased to six.
48714 Added ability for the phone to mute the microphone when auto-answering a call.
48750 The Web-based configuration utility now enables the user to configure outbound proxies on a perline basis.
48757 Contacts added to the list are now highlighted and displayed without the need to scroll up or
down to view the addition.
50258 Enhanced the method of notifying the user of error and warning indications.
51101 Added the ability to use an Emergency Location Identification Number (ELIN) from LLDP-MED to
add a P-Asserted-Identity when using emergency routing:
dialplan.routing.emergency.preferredSource=[ELIN|Config] (default ELIN)
dialplan.routing.emergency.outboundIdentity=xxxxxxxx (default null)
dialplan.routing.emergency.outboundIdentity.lldp=xxxxxxxx (default null).
51471 Added a configuration option to disable the test of subject’s CommonName against the
registration address (associated with CA management).
52844 Added certificate validation for 802.1X.
Polycom, Inc.
55
Polycom UC Software 4.1.5 Release Notes
53128 Added a configuration option to modify the Backlight timeout duration.
53360 Added the ability to display the phones current ARP table in the diagnostic menu (applies to
SpectraLink 84xx).
53908 The Web-based configuration utility now offers the ability to configure soft keys and line-keys.
54301 The timestamp is now displayed alongside the caller in the Call Lists.
54648 Added HTTPS support in the Updater that was previously called BootROM.
54680 Introduced the ability to import and export local and global configuration files using a PC browser.
54683 The browser-based SW Upgrade button that enables user to upgrade phones with one of multiple
compatible software versions is available on the Polycom provisioning server.
54730 Noticeable enhancement from the time the phone is powered up and when it is ready for use.
56150 Added Data Link Layer L2 Discovery between phones and PC.
56187 Added ToID and FromID in SIP Publish packets for VQMon reports.
56274 Added multicast group paging based on the SpectraLink PTT solution.
56942 Configuring Soft key (EFK) settings no longer require a reboot in order to take effect.
57392 Added support to the microbrowser for HTTP proxy authentication (applies to SpectraLink 84xx).
57981 Added support for custom device certificates.
58007 Added the ability to revoke certificates used in SSL transactions by using OCSP.
58336 Added SHOULD SDP answer behavior as per RFC 3264.
58507 Enhanced the Web-based configuration and provisioning utility.
60297 Added the ability of random distribution of polling to check for software upgrades.
60907 Added the ability to disable Call Waiting while still allowing further outgoing calls.
61051 Added the ability to display custom soft keys on input forms in the microbrowser.
61138 Added support for incoming TLS connections on the Web server.
61343 Added the ability to disable authentication verification for received SRTP packets.
62671 Added a time-stamped log event indicating when the phone is ready to be used.
63592 Added API calls to the microbrowser for Media Player.
63629 Added Sennheiser EHS configuration menus and options.
64144 The alerting LED and associated line-key animation for second and subsequent incoming calls
are now disabled when the Call Waiting feature waiting is disabled.
64243 The API Data push message size limit has been increased to 2048 bytes from 1024 bytes.
64359 Converted the BLA dialog rendering from No to Yes for user agents that are a remote party to the
existing call dialog.
65287 Added the ability to prevent a phone from being provisioned at start-up.
Configuration parameter prov.startupCheck.enabled [default = 1 (enabled)]
66212 Added support for setting the syslog server address from DHCP.
Polycom, Inc.
56
Polycom UC Software 4.1.5 Release Notes
66323 Added an administrator operations menu in the Updater to the setup menu: Reboot, Reset
Settings, Format File System, and Install BootBlock.
66604 The phone reports connectivity event notifications to an 802.1x enabled switch port when a nonauthenticated PC disconnects or reconnects to the phone.
67600 Password and other security entry fields now perform a brief echo of entered characters before
being obscured from view.
68110 Added control of available telephony features on the Office Communications Server (OCS) using
the reg.x.telephony configuration parameter.
68899 Added the ability on the microbrowser to enter two-digit dial pad values for selecting entries in a
list.
69225 Added the ability to allow a hard key to be directly assigned an Enhanced Feature Key (EFK)
style macro.
69442 Productivity features such as LDAP, Local Call Recording, and Visual Conference Management
are enabled without the requirement of a license file. Note that VQMon will remain a licensable
feature.
71633 The Reset setting in the Updater menu does not erase the CA and Device Certificates.
Enhanced Capabilities
31158 Instant messages can now be sent if msg.bypassInstantMessage=1. The phone menu will
no longer be bypassed after pressing the Messages button.
38407 After reboot, the phones now transmit a TCP message to the outbound proxy address.
39249 Distortion on sound from a gateway call back has been removed (applies to SoundPoint IP 330,
550, 560, and 650).
40103 The file name of a file copied to a full USB stick full no longer displays (applies to SoundPoint IP
650 and 670).
40393 The backlight adjustment has been adjusted to work correctly when the incoming call times out.
41662 The buzzing sound heard on the far end user in hands free mode when a call is answered while
ringing has been removed (applies to SoundPoint IP 550, 650, and 670).
41897 The sound heard on the phone when attempting to cancel a conference or transfer has been
removed.
42427 On the phone microbrowser, the thin line over the data field has been removed.
42442 The Select hard key has been made functional in the speed dial menu (applies to SoundPoint IP
330).
43822 When there is an active call, the backlight now adjusts properly.
43846 The menu widget now scales to the correct size of the menu (applies to SpectraLink 84xx).
43864 The Soft key, line key and status widgets can now be scaled (applies to SpectraLink 84xx).
44981 The phone now seizes the correct line for speed dial when
call.stickyAutoLineSeize.onHookDialing=1.
Polycom, Inc.
57
Polycom UC Software 4.1.5 Release Notes
45411 The SoundPoint IP 550 and 650 speaker phone volume can now be adjusted via gain settings for
Rx audio.
45806 An unsupported format message no longer appears when trying to play a short WAV file.
45889 Lighten and Darken soft keys now display for the selected background image only in the
Background menu (applies to SoundPoint IP 450, 550, 560, and 650).
45900 The time and date now display on the multiple call appearances screen (applies to SoundPoint IP
450).
46134 The phones now play a default ringtone when the ringtone size is larger than the tone quota or
the ringtone is not in the cache.
46170 On the phone menu, the Local Directory or Corporate Directory cursor can now reach the end of
the highlighting bar (applies to SoundPoint IP 450).
46773 On the microbrowser, the backspace soft key is now made available when the user enters a
character to the input box (applies to SoundPoint IP 320, 330, 430, and 450).
48153 In the phone menu password settings, deleting a character before the character timeout now
clears the last asterisk symbol.
48217 When ramdisk.nBlocks=0 is set, ramdisk.nBlocks no longer consumes extraneous
memory.
48753 The XML dictionary download no longer fails when the dictionary file size exceeds the defined
size.
50234 The phone no longer crashes while starting a native application (applies to SpectraLink 84xx).
50633 When the user enters text for a contact in the Contact Directory, the backspace soft key now
appears before the character selection widget for the first character has closed (applies to
SoundPoint IP 330 and 331).
50735 After a conference call, redial now dials the last dialed number (applies to SoundPoint IP 330 and
335).
50745 Pressing the hookswitch toggle quickly no longer creates a phone and headset mismatch.
50766 During a save confirmation screen, if there is a missed call, the contact can now be saved.
(SoundPoint IP 330, 331, and 335).
50788 When the user tries to play a recorded audio file from Menu/Status/Diagnostics/Test
Hardware/Audio Diagnostics on different termination points (Handsfree/Headset/Handset), the
icons are now updated (applies to SoundPoint IP 450).
50972 SIP call format is no longer missing for URL dialing (applies to SoundPoint IP 330 and 335).
51238 In the Install Custom CA Certificate menu on the phone, the 1/A/a soft key is no longer missing
(applies to SoundPoint IP 450, 550, 560, 650, and 670).
51301 A loud ring has been removed from the speaker when canceling a conference call or switching
between calls.
51493 When call forward is enabled on the second registered line, phones now display the text string
Call Forward Enabled on the top of the UI (applies to SoundPoint IP 450, 550, 560, 650, and
670).
Polycom, Inc.
58
Polycom UC Software 4.1.5 Release Notes
51751 When there are multiple calls waiting, dropping one remote party now plays the call waiting ring
on the originating phone.
51767 The phone no longer crashes when trying to add a large number of contacts.
51930 The phone now shows Connecting: instead of Transfer to: on the top UI when initiating a transfer
(applies to SoundPoint IP 330 and 335).
51994 When the contact is highlighted in the Contact Directory, pressing the character selection widget
no longer erases the highlight bar (applies to SoundPoint IP 330, 331, and 335).
51996 Trying to dial an invalid speed dial number no longer causes slight corruption in the phone UI
(applies to SoundPoint IP 330, 331, and 335).
52006 The call waiting tone no longer changes to a single beep when a double beep is configured on
the phone.
52007 When a call is automatically disconnected at the far end phone after time out, the current active
call no longer goes on hold inadvertently.
52103 The phones no longer display the first line label in scrolling status bar when it is visible (applies to
SoundPoint IP 330, 331, and 335).
52112 In the phone Contact Directory menu, when the 1/A/a soft key is pressed to change the
capitalization of the letters, the encoding no longer resets to ASCII (applies to SoundPoint IP 450,
560, and 670).
52219 In the phone Audio Diagnostics Menu, pressing the left arrow to exit now restores the previously
selected termination state (applies to SoundPoint IP 450, 560, and 670).
52270 Backlight values now match the phone menu option and override file parameters.
52276 When a call is answered automatically while a recorded WAV file is playing the audio player
screen now exits properly (applies to SoundPoint IP 650).
52380 When the phone lines are configured to call server and presence server respectively, the
presence information now displays on the first line as well as the presence line.
52489 Character encoding is no longer available while entering the contact information in the contact
directory (applies to SoundPoint IP 430, 550, 650, and 670).
52552 The momentarily observed UI corruption/flickering during an incoming call with a long caller ID
has been resolved (applies to SoundPoint IP 330, 331, and 335).
52560 Menu titles now fit in the phone UI (applies to SoundPoint IP 330, 331, and 335).
52688 Enhanced the mb.main.idleTimeout parameter behavior.
52692 The character entry mode now shows consistently when entering passwords in the phone menu
(applies to SoundPoint IP 450, 560, and 670).
52734 The password field now clears after entering an invalid password (applies to SoundPoint IP 330,
331, and 335).
52766 The speaker/headset key LED no longer remains ON when the active call is on hold while there is
an incoming call on the same line (applies to SoundPoint IP 550, 560, 650, and 670).
52789 The phone settings menu now has an appropriate label for the menu item in Handsfree Mode.
Polycom, Inc.
59
Polycom UC Software 4.1.5 Release Notes
52917 In the phone Install Custom CA Cert menu, the character selection widget no longer remains
visible when closed (applies to SoundPoint IP 330, 331, and 335).
52920 When a custom CA cert URL is unreachable, an appropriate message now displays on the
phone.
52945 Inappropriate characters no longer display in the quick search menu (applies to SoundPoint IP
330, 331, and 335).
52948 When long text is entered in the quick search menu, the text now moves forward and displays the
last character (applies to SoundPoint IP 330, 331, and 335).
53055 When composing a new instant message and if there is a new incoming instant message, the UI
no longer becomes corrupted (applies to SoundPoint IP 560 and 670).
53101 VQMon values displayed on the SQmediator are now the same as the single SIP-Publish packet
values.
53138 Instant messaging strings now have spaces in between words in all instances.
53142 Extra spaces at the beginning and end of the phone labels have been removed.
53235 Extra spaces in the phone exit menu have been removed.
54147 The phone conference screen titles are no longer truncated when using certain languages
(applies to SoundPoint IP 330, 331, and 335).
54449 The phone no longer displays an error message when trying to edit a long contact number.
54553 When the user tries to use two lines to dial, the user no longer sees a scrolling message instead
of Enter Number text (applies to SoundPoint IP 450, 650, and 670).
54913 In a BLF scenario, when the monitored phone places a call to another phone, the Dialog Event
Package no longer contains repeated remote identity when its INVITE has received an initial 407
or 401 response.
55639 When the enhanced BLF feature is enabled on an active call, the call state no longer changes in
the call appearance for monitored users (applies to SoundPoint IP 650).
55655 Pressing the message hard key now leads the user to voicemail (applies to SoundPoint IP 450,
550, 560, 650, and 670).
55669 When the phone is configured as TCP only, and the phone receives a REFER in UDP, the phone
now sends an INVITE in TCP.
55681 When transport is set to TCP, Refer-Based Click-To-Dial now works when the phone has an
active call.
55852 When the phone is in the setup menu, pressing * key now always moves a page up (applies to
SoundPoint IP 450, 550, 560, 650, and 670).
55957 When the BLF feature is enabled, the remote call appearance screen now properly times out and
does not wait until the call is ended by the monitored user.
57538 In the phone menus, field names no longer truncate when the user tries to make edits (applies to
SpectraLink 84xx).
57625
Applications are now loading as per the order specified (applies to SpectraLink 84xx).
Polycom, Inc.
60
Polycom UC Software 4.1.5 Release Notes
58860 When the forward feature is enabled, the number of rings set now matches the actual ring
cadences.
59086 When the phone is configured to an external server like CMA, the phone clock format (12 hrs –
24 hrs) does not get affected until the phone reboots.
59202 When the phone loses an active call on hold, pressing resume no longer drops the call.
59285 The phone no longer shows a delete (<<) soft key when there are no numbers to delete (applies
to SoundPoint IP 330, 331, and 335).
59355 The phone no longer logs error messages when it is unable to connect to any of the telephony
notification URLs.
59463 When using the phone’s Web configuration, the phone no longer restarts when updating
telephony notification event or URL.
59478 In the phone digit map, segments longer than 40 characters no longer truncated to 40 when
applied.
61100 Added the ability to override complex audio codec instance count definition for each individual
codec type.
61553 The phone no longer crashes when trying to split a conference service which is unavailable.
63190 The macro $FServerACDSignIn$ now works when configuring the soft key using EFK to exercise
the ServerACDSignIn function.
63582 The excessively long boot time resulting from FTP errors and failures has been noticeably
decreased (applies to SpectraLink 84xx).
64389 Added the ability to set the correct TLS Profile using the Updater and/or Application UI menus.
64455 There is no longer a delay between the time the Push URL is sent to the phone and the time it
takes the browser to execute the fetch URL (applies to SpectraLink 84xx).
64464 The phones no longer wait to auth/re-associate to AP until AP starts the full security exchange
(applies to SpectraLink 84xx).
64693 The payload settings specified by the phone are now used by the receiving phone.
64932 When the server side Call Forward No Answer (CFNA) is enabled, the user no longer has the
option to select the number of rings on the local phone.
65081 The user is now able to navigate on the phone menus having select options available (applies to
SpectraLink 84xx).
65082 The radio performance has been improved to reduce the reported number of missed packets and
high retry rates (applies to SpectraLink 84xx).
65255 Selected options on the menus no longer disappear when selected from the phone navigation
right hard key (applies to SpectraLink 84xx).
65275 When persistence login is enabled for default, the user log out no longer reboots the phone.
65309 Incorrect soft key options no longer show up when certain selections are invoked in the menu/UI
(applies to SpectraLink 84xx).
65337 The phones now provision correctly via HTTPS.
Polycom, Inc.
61
Polycom UC Software 4.1.5 Release Notes
65622 In case of emergency failover, the correct information with Invite request is routed (applies to
SoundPoint IP 450, 650, and 335).
66582 In the quick setup menu, the unwanted Ok soft key no longer appears while changing the Boot
server options (applies to SpectraLink 84xx).
66975 The voicemail icon now displays when there is a voicemail notification on the phone (applies to
SpectraLink 84xx).
67928 In the phone buddy list, the pop-up message Contact already exists has been resolved.
68345 The phone dial pad keys now wake/light up when the phone comes back from the power save
mode (applies to SpectraLink 84xx).
68533 A reboot is no longer necessary to change the parameter
voIpProt.SIP.conference.address in the configuration files.
69372 During an IM chat session, the phone now displays all messages using the same quick note
string (applies to SpectraLink 84xx).
69373 When provisioning TLS applications, the CommonName of a server certificate is now
configurable with the new configuration option.
69374 User interface changes have been made in the Application menu and BootROM menu for SIP
and Provisioning applications respectively to make CommonName configurable.
69929 When the BLF feature is enabled, the monitored BLF line status now updates as busy after the
attendant phone transfers a call to that line (applies to SoundPoint IP 650).
69965 When the soft key is configured with capital HTTP in the URL, it no longer tries to dial instead of
using the phone microbrowser.
70258 Resetting the phone to factory settings no longer clears the password (applies to SpectraLink
84xx).
70458 Text on the input fields and soft keys are now properly displayed.
70547 Download Custom CA Cert screen now disappears after saving a certificate (applies to all
SoundPoint IP).
70633 The phone no longer mishandles 403 responses to first REFER sent to phone to centralized
conference server.
70732 The links on the microbrowser page are no longer hidden when the links are highlighted and
moves to another link.
70908 When using user profiles, the phone no longer powers off at the user login prompt (applies to
SpectraLink 84xx).
71046 When the phone is in a conference call and a roaming attempt is made, the access point no
longer rejects the reassociation request (applies to SpectraLink 84xx).
71103 When the phone is configured as per call center mode, call hold is no longer treated as a missed
call (applies to SoundPoint IP 650).
71156 When there is an active call between two parties, accepting another call no longer makes the
phone vibrate continuously when the mode is set to Ring and Vibrate (applies to SpectraLink
84xx).
Polycom, Inc.
62
Polycom UC Software 4.1.5 Release Notes
71913 Registered lines now display on Expansion modules (applies to SoundPoint IP 650, 670).
Configuration File Enhancements
Certain groups of configuration parameters have been modified in UC software 4.0.0. In these cases,
instead of listing every parameter, the following table will specify a group of related parameters with an
abbreviated XML path name ending with (.*).
For example, suppose the following parameters are modified: device.wifi.enabled,
device.wifi.ipAddress, and device.wifi.ssid. Since these parameters all begin with
device.wifi, the following table abbreviates these parameters as device.wifi.*
Note: Parameters with .set
Most device parameters have identical parameters ending with .set. The .set parameters are
not included in the following table.
Web Info: Parameters Changed in UC Software 4.0.0
The following table includes parameters changed in UC software 4.0.0. You can find the new
descriptions and values in the Polycom UC Software Administrators Guide.
Table 12: UC Software 4.0.0 Parameter Enhancements
Modification
Configuration Parameter
Description
Discontinued
apps.x.Label
Productivity Applications parameter
Discontinued
apps.x.Url
Productivity Applications parameter
Discontinued
apps.ucdesktop.IP
Productivity Applications parameter
Discontinued
apps.ucdesktop.name
Productivity Applications parameter
Discontinued
apps.ucdesktop.port
Productivity Applications parameter
Discontinued
device.auth.*
Provisioning parameters
The parameters
device.auth.localAdminPassword and
device.auth.localUserPassword have not been
removed
Discontinued
device.dhcp.offerTimeout
Provisioning parameter
Discontinued
device.prov.appProvString
Provisioning parameter
Discontinued
device.prof.appProvType
Provisioning parameter
Discontinued
device.sec.SSL.*
Provisioning parameters
Polycom, Inc.
63
Polycom UC Software 4.1.5 Release Notes
Modification
Configuration Parameter
Description
Discontinued
device.sec.deviceCertEnabled
Provisioning parameter
Discontinued
exchange.server.address
Productivity Applications parameter
Discontinued
httpd.lp.port
Provisioning parameter
Discontinued
lcl.datetime.date.digitFormatEnable
User preference parameter
Discontinued
log.level.change.lp
Log parameter
Discontinued
log.level.change.nwmgr
Log parameter
Discontinued
log.level.change.sync
Log parameter
Discontinued
reg.x.filterReflectedBlaDialogs
Call feature parameter
Discontinued
reg.x.server.H323.y.register
Call feature parameter
Discontinued
sec.TLS.customDeviceCert.enable
Security parameter
Discontinued
sec.dot1x.eapollogoff.pcforcelanlinkreset
Security parameter
Discontinued
voIpProt.SDP.useLegacyPayloadType
Call feature parameter
Negotiation
Discontinued
voIpProt.server.H323.x.register
Call feature parameter
Discontinued
voice.aec.hd.*
Audio parameters
The parameter voice.aec.hd.enable has not
been removed
Discontinued
voice.aec.hf.*
Audio parameters
The parameter voice.aec.hf.enable has not
been removed
Discontinued
voice.aec.hs.*
Audio parameters
The parameter voice.aec.hs.enable has not
been removed
Discontinued
voice.aes.hd.duplexBalance
Audio parameter
Discontinued
voice.aes.hf.*
Audio parameters
The parameter voice.aes.hf.enable has not
been removed
Discontinued
voice.aes.hs.duplexBalance
Audio parameter
Discontinued
voice.gain.rx.digital.ringer.*
Audio parameters
The parameter voice.gain.rx.digital.ringer
has also been removed
Discontinued
Polycom, Inc.
voice.handset.wideband
Audio parameter
64
Polycom UC Software 4.1.5 Release Notes
Modification
Configuration Parameter
Description
Discontinued
voice.rxEq.hf.postFilter.*
Audio parameters
The parameter
voice.rxEq.hf.postFilter.enable has not
been removed
Discontinued
voice.rxEq.hf.preFilter.*
Audio parameters
The parameter
voice.rxEq.hf.preFilter.enable has not been
removed
Discontinued
voice.rxEq.hs.postFilter.*
Audio parameters
The parameter
voice.rxEq.hs.postFilter.enable has not
been removed
Discontinued
voice.rxEq.hs.preFilter.*
Audio parameters
The parameter
voice.rxEq.hs.preFilter.enable has not been
removed
Added
apps.x.label
Productivity Applications parameter
Added
apps.x.url
Productivity Applications parameter
Added
apps.push.secureTunnelEnabled
Productivity Applications parameter
Added
apps.push.secureTunnelPort
Productivity Applications parameter
Added
apps.push.secureTunnelRequired
Productivity Applications parameter
Added
apps.statePolling.responseMode
Productivity Applications parameter
Added
apps.telNotification.callStateChangeEvent
Productivity Applications parameter
Added
apps.telNotification.userLogInOutEvent
Productivity Applications parameter
Added
apps.ucdesktop.*
Productivity Applications
parameters
The parameter apps.ucdesktop.enabled has
existed in previous versions
Added
bg.color.*
Background parameter
Added
bluetooth.radioOn
Call feature parameter
Added
call.advancedMissedCalls.*
Call feature parameters
Added
call.callWaiting.enable
Call feature parameter
Added
call.localConferenceEnabled
Call feature parameter
Added
callLists.*
Call feature parameters
Added
device.hostname
Provisioning parameter
Polycom, Inc.
65
Polycom UC Software 4.1.5 Release Notes
Modification
Configuration Parameter
Description
Added
device.net.dhcpBootServer
Provisioning parameter
Added
device.net.dot1x.*
Provisioning parameters
Added
device.pacfile.*
Provisioning parameters
Added
device.prov.upgradeServer
Provisioning parameter
Added
device.sec.TLS.*
Provisioning parameters
Added
device.usbnet.*
Provisioning parameters
Added
device.wifi.*
Provisioning parameter
Added
dialplan.applyToPstnDialing
Call feature parameter
Added
dialplan.routing.emergency.outboundIdentity
Call feature parameter
Added
dialplan.routing.emergency.outboundIdentity
.lldp
Call feature parameter
Added
dialplan.routing.ermgency.preferredSource
Call feature parameter
Added
exchange.meeting.*
Productivity Applications parameter
Added
exchange.server.url
Productivity Applications parameter
Added
feature.audioVideoToggle.enabled
Call feature parameter
Added
feature.bluetooth.enabled
Call feature parameter
Added
feature.enhancedCallDisplay.enabled
Call feature parameter
Added
feature.exchangeCalendar.enabled
Call feature parameter
Added
feature.nonVolatileRingerVolume.enabled
Call feature parameter
Added
httpd.cfg.secureTunnelEnabled
Web Configuration Utility parameter
Added
httpd.cfg.secureTunnelPort
Web Configuration Utility parameter
Added
httpd.cfg.secureTunnelRequired
Web Configuration Utility parameter
Added
httpd.ta.secureTunnelEnabled
Web Configuration Utility parameter
Added
httpd.ta.secureTunnelPort
Web Configuration Utility parameter
Added
httpd.ta.secureTunnelRequired
Web Configuration Utility parameter
Added
ind.pattern.blink.*
LED indicator parameter
Added
ind.pattern.flashSlow2.*
LED indicator parameter
Added
lcl.x.pstnCountry
Multilingual parameter
Added
lcl.aidt
Multilingual parameter
Polycom, Inc.
66
Polycom UC Software 4.1.5 Release Notes
Modification
Configuration Parameter
Description
Added
lcl.callerId
Multilingual parameter
Added
lcl.callerIdType
Multilingual parameter
Added
lcl.country.*
Multilingual parameters
The parameter lcl.country has also been
added
Added
lcl.dtmfLevel
Multilingual parameter
Added
lcl.dtmfTwist
Multilingual parameter
Added
lcl.flashTiming
Multilingual parameter
Added
lcl.pstnCountryIndex
Multilingual parameter
Added
lineKey.*
Flexible line key assignment
parameters
Added
log.level.change.barcd
Log parameter
Added
log.level.change.bluet
Log parameter
Added
log.level.change.clist
Log parameter
Added
log.level.change.daa
Log parameter
Added
log.level.change.dock
Log parameter
Added
log.level.change.drvbt
Log parameter
Added
log.level.change.oaip
Log parameter
Added
log.level.change.ocsp
Log parameter
Added
log.level.change.pdc
Log parameter
Added
log.level.change.pres
Log parameter
Added
log.level.change.pstn
Log parameter
Added
log.level.change.ptt
Log parameter
Added
log.level.change.rtls
Log parameter
Added
log.level.change.tls
Log parameter
Added
log.level.change.wifi
Log parameter
Added
log.render.stdout.*
Log parameter
The parameter log.render.stdout has existed
in previous versions
Polycom, Inc.
67
Polycom UC Software 4.1.5 Release Notes
Modification
Configuration Parameter
Description
Added
mb.main.toolbar.autoHide.*
Microbrowser parameters
The parameter
mb.main.toolbar.autoHide.enabled has
existed in previous versions
Added
messaging.*
SpectraLink instant messaging
parameters
Added
np.*
SpectraLink notification profiles
parameters
Added
oai.*
SpectraLink Open Application
Interface parameters
Added
prov.login.*
Distributed polling parameters
Added
prov.loginCredPwdFlushed.enabled
Distributed polling parameter
Added
prov.polling.timeRandomEnd
Distributed polling parameter
Added
prov.startupCheck.enabled
Provisioning parameter
Added
pstn.*
Added
ptt.*
Paging and push-to-talk
parameters
Added
qbc.*
SpectraLink quick barcode
connector parameters
Added
qos.ethernet.*
SpectraLink QoS parameters
The parameters
qos.ethernet.callControl.user_priority,
qos.ethernet.other.user_priority,
qos.ethernet.rtp.user_priority, and
qos.ethernet.rtp.video.user_priority
existed in previous versions
Added
reg.x.auth.domain
Call feature parameter
Added
reg.x.auth.useLoginCredentials
Call feature parameter
Added
reg.x.gruu
Call feature parameter
Added
reg.x.server.y.specialInterop
Call feature parameter
Added
reg.x.server.y.useOutboundProxy
Call feature parameter
Added
reg.x.srtp.enable
Call feature parameter
Added
reg.x.srtp.offer
Call feature parameter
Added
reg.x.srtp.require
Call feature parameter
Polycom, Inc.
68
Polycom UC Software 4.1.5 Release Notes
Modification
Configuration Parameter
Description
Added
reg.x.telephony
Call feature parameter
Added
se.pat.misc.customX.*
Sound effects parameters
Added
se.pat.misc.miscX.*
Sound effects parameters
Added
se.rt.answerMute.*
Sound effects parameters
Added
se.rt.autoAnswer.micMute
Sound effects parameter
Added
se.rt.autoAnswer.videoMute
Sound effects parameter
Added
se.rt.customX.micMute
Sound effects parameter
Added
se.rt.customX.videoMute
Sound effects parameter
Added
se.rt.default.micMute
Sound effects parameter
Added
se.rt.default.videoMute
Sound effects parameter
Added
se.rt.emergency.micMute
Sound effects parameter
Added
se.rt.emergency.videoMute
Sound effects parameter
Added
se.rt.external.micMute
Sound effects parameter
Added
se.rt.external.videoMute
Sound effects parameter
Added
se.rt.internal.micMute
Sound effects parameter
Added
se.rt.internal.videoMute
Sound effects parameter
Added
se.rt.precedence.micMute
Sound effects parameter
Added
se.rt.precedence.videoMute
Sound effects parameter
Added
se.rt.ringAnswerMute.*
Sound effects parameters
Added
se.rt.splash.micMute
Sound effects parameter
Added
se.rt.splash.videoMute
Sound effects parameter
Added
se.rt.visual.micMute
Sound effects parameter
Added
se.rt.visual.videoMute
Sound effects parameter
Added
sec.TLS.SIP.strictCertCommonNameValidation
Security parameter
Added
sec.TLS.customCaCert.*
Security parameters
Added
sec.TLS.customDeviceCert.*
Security parameters
Added
sec.TLS.customDeviceKey.*
Security parameters
Added
sec.TLS.profile.*
Security parameters
Polycom, Inc.
69
Polycom UC Software 4.1.5 Release Notes
Modification
Configuration Parameter
Description
Added
sec.TLS.profileSelection.*
Security parameters
Added
sec.hostMoveDetect.*
Security parameters
Added
sec.srtp.holdWithNewKey
Security parameter
Added
sec.srtp.mki.length
Security parameter
Added
sec.srtp.resumeWithNewKey
Security parameter
Added
softkey.x.insert
Security parameter
Added
tcpIpApp.fileTransfer.waitForLinkIfDown
IP parameter
Added
tone.chord.misc.A3Major.*
Tone parameters
Added
tone.chord.misc.C3Major.*
Tone parameters
Added
tone.chord.misc.Db3Major.*
Tone parameters
Added
tone.chord.misc.E3Major.*
Tone parameters
Added
tone.chord.misc.cs12.*
Tone parameters
Added
up.25mmRealTime
Default 1
Used to configure whether a mobile
phone or a PC is connected to the
2.5 mm port in the conference
phones.
min="1" max="2"
Added
up.backlight.timeout.*
User preferences parameters
The parameter up.backlight.timeout has also
been added
Added
up.cfgWarningsEnabled
User preferences parameter
Added
up.displayOperMode
Default 0
Phone can display the status i.e.,
Up/Down when it is working on
PSTN mode(Applicable to
SoundStation duo).
Added
up.headsetOnlyAlerting
User preferences parameter
Added
up.hearingAidCompatibility.enabled
User preferences parameter
Added
up.hideDateTimeWhenNotSet
User preferences parameter
Added
up.multiKeyAnswerEnabled
User preferences parameter
Added
up.operMode
User preferences parameter
Polycom, Inc.
70
Polycom UC Software 4.1.5 Release Notes
Modification
Configuration Parameter
Description
Added
up.pstnSetup
Default 0
User can setup the PSTN line by
selecting the country when the
phone initially boots up
Added
up.warningLevel
User preferences parameter
Added
upgrade.*
Provisioning parameter
Added
video.callMode.default
Video parameter
Added
video.debug
Video parameter
Added
voIpProt.SIP.dialog.strictXLineId
Call feature parameter
Added
voIpProt.SIP.IM.autoAnswerDelay
Call feature parameter
Added
voIpProt.SIP.mtls.enable
Call feature parameter
Added
voIpProt.SIP.pingMethod
Call feature parameter
Added
voIpProt.server.x.specialInterop
Call feature parameter
Added
voIpProt.server.x.useOutboundProxy
Call feature parameter
Added
voice.aec.bt.hd.enable
Audio parameter
Added
voice.aec.usb.hf.enable
Audio parameter
Added
voice.aes.bt.hd.enable
Audio parameter
Added
voice.aes.usb.hf.enable
Audio parameter
Added
voice.agc.bt.hd.enable
Audio parameter
Added
voice.agc.usb.hf.enable
Audio parameter
Added
voice.bt.*
Audio parameters
Added
voice.handset.rxag
Audio parameter
Added
voice.handset.rxdg
Audio parameter
Added
voice.handset.st.
Audio parameter
Added
voice.handset.txag
Audio parameter
Added
voice.handset.txdg
Audio parameter
Added
voice.handsfree.*
Audio parameters
Added
voice.headset.rxag
Audio parameter
Added
voice.headset.rxdg
Audio parameter
Added
voice.headset.st
Audio parameter
Polycom, Inc.
71
Polycom UC Software 4.1.5 Release Notes
Modification
Configuration Parameter
Description
Added
voice.headset.txag
Audio parameter
Added
voice.headset.txdg
Audio parameter
Added
voice.ns.bt.*
Audio parameters
Added
voice.ns.usb.*
Audio parameters
Added
voice.ringer.rxag
Audio parameter
Added
voice.rxEq.usb.*
Audio parameters
Added
voice.rxQos.ptt.*
Audio parameters
Added
voice.rxQos.wireless.*
Audio parameters
Added
voice.txEq.usb.*
Audio parameters
Added
voice.usb.*
Audio parameters
Added
voice.volume.persist.bluetooth.headset
Audio parameter
Added
voice.volume.persist.usb.handsfree
Audio parameter
Added
wifi.*
Wifi parameters
Changed
apps.push.messageType
Productivity Applications parameter
Changed
apps.uc.desktop.enabled
Productivity Applications parameter
Changed
call.autoRouting.preferredProtocol
Call feature parameter
Changed
device.auth.*
Provisioning parameters
Changed
device.cma.mode
Provisioning parameter
Changed
device.dhcp.*
Provisioning parameters
The parameter device.dhcp.bootSrvOpt has not
been changed
Changed
device.dns.*
Provisioning parameters
Changed
device.em.power
Provisioning parameter
Changed
device.line.*
Provisioning parameters
Changed
device.net.*
Provisioning parameters
The parameters device.net.dhcpBootServer,
device.net.IPgateway,
device.net.subnetMask, and
device.net.vlanId have not been changed
Changed
Polycom, Inc.
device.ntlm.versionMode
Provisioning parameter
72
Polycom UC Software 4.1.5 Release Notes
Modification
Configuration Parameter
Description
Changed
device.prov.*
Provisioning parameters
The parameters device.prov.password,
device.prov.serverName,
device.prov.upgradeServer, and
device.prov.user have not been changed
Changed
device.serial.enable
Provisioning parameter
Changed
device.sntp.gmtOffset
Provisioning parameter
Changed
device.syslog.*
Provisioning parameters
The parameter device.syslog.serverName has
not been changed
Changed
dialplan.x.digitmap
Call feature parameter
Changed
dialplan.x.routing.server.y.transport
Call feature parameter
Changed
dialplan.digitmap
Call feature parameter
Changed
dialplan.digitmap.timeOut
Call feature parameter
Changed
dialplan.impossibleMatchHandling
Call feature parameter
Changed
dialplan.removeEndOfDial
Call feature parameter
Changed
dialplan.routing.server.x.transport
Call feature parameter
Changed
dir.H350.dev.attribute.x.type
Directory parameter
Changed
dir.H350.dev.transport
Directory parameter
Changed
dir.H350.group.attribute.x.type
Directory parameter
Changed
dir.H350.group.transport
Directory parameter
Changed
dir.H350.person.attribute.x.type
Directory parameter
Changed
dir.H350.person.transport
Directory parameter
Changed
dir.corp.attribute.x.type
Directory parameter
Changed
dir.corp.transport
Directory parameter
Changed
dir.local.nonVolatile.maxSize
Directory parameter
Changed
dir.local.volatile.maxSize
Directory parameter
Changed
divert.x.autoOnSpecificCaller
Call feature parameter
Changed
divert.x.contact
Call feature parameter
Changed
divert.x.sharedDisabled
Call feature parameter
Changed
divert.busy.*
Call feature parameters
Polycom, Inc.
73
Polycom UC Software 4.1.5 Release Notes
Modification
Configuration Parameter
Description
Changed
divert.dnd.*
Call feature parameters
Changed
divert.fwd.x.enabled
Call feature parameter
Changed
divert.noanswer.*
Call feature parameters
Changed
ind.led.x.index
LED indicator parameter
Changed
keypadLock.*
Phone lock parameters
Changed
lcl.ml.lang.clock.x.format
Multilingual parameter
Changed
lcl.ml.lang.list
Multilingual parameter
Changed
lcl.ml.lang.menu.*
Multilingual parameters
Changed
lcl.ml.lang.tags.*
Multilingual parameters
Changed
log.level.change.slog
Log parameter
Changed
log.render.file.size
Log parameter
Changed
log.render.file.upload.append.limitMode
Log parameter
Changed
log.render.file.upload.period
Log parameter
Changed
log.render.stdout
Log parameter
Changed
log.sched.*
Log parameters
Changed
msg.bypassInstantMessage
Voicemail parameter
Changed
nat.*
IP parameters
The parameter nat.keepalive.interval has
not been changed
Changed
phoneLock.enabled
Phone lock parameter
Changed
pnet.remoteCall.dtmfDuration
Peer networking parameter
Changed
powerSaving.enable
Power saving parameter
Changed
prov.fileSystem.ffs0.minFreeSpace
Provisioning parameter
Changed
prov.polling.mode
Distributed polling parameter
Changed
prov.polling.time
Distributed polling parameter
Changed
qos.ethernet.*
Quality of Service parameters
Changed
qos.ip.callControl.*
Quality of Service parameters
The parameters qop.ip.callControl.dscp.*
have not been changed
Polycom, Inc.
74
Polycom UC Software 4.1.5 Release Notes
Modification
Configuration Parameter
Description
Changed
qos.ip.rtp.*
Quality of Service parameters
The parameters qos.ip.rtp.dscp.* and
qos.ip.rtp.video.dscp.* have not been
changed
Changed
reg.x.callsPerLineKey
Line registration parameter
Changed
reg.x.outboundProxy.transport
Line registration parameter
Changed
reg.x.ringType
Line registration parameter
Changed
reg.x.server.y.transport
Line registration parameter
Changed
res.finder.minFree
Phone memory parameter
Changed
res.finder.sizeLimit
Phone memory parameter
Changed
res.quotas.background
Phone memory parameter
Changed
res.quotas.bitmap
Phone memory parameter
Changed
res.quotas.cache
Phone memory parameter
Changed
res.quotas.font
Phone memory parameter
Changed
res.quotas.tone
Phone memory parameter
Changed
res.quotas.xmlui
Phone memory parameter
Changed
roaming_buddies.reg
SpectraLink call feature parameter
Changed
roaming_privacy.reg
SpectraLink call feature parameter
Changed
se.destination
Sound effects parameter
Changed
se.pat.callProg.msgWaiting.name
Sound effects parameter
Changed
se.pat.misc.instantMessage.name
Sound effects parameter
Changed
se.pat.misc.localHoldNotification.name
Sound effects parameter
Changed
se.pat.misc.messageWaiting.name
Sound effects parameter
Changed
se.pat.misc.negativeConfirm.name
Sound effects parameter
Changed
se.pat.misc.positiveConfirm.name
Sound effects parameter
Changed
se.pat.misc.remoteHoldNotification.name
Sound effects parameter
Changed
se.pat.misc.welcome.name
Sound effects parameter
Changed
sec.H235.*
Sound effects parameters
Changed
tcpIpApp.keepalive.*
IP parameters
Changed
tcpIpApp.port.*
IP parameters
Polycom, Inc.
75
Polycom UC Software 4.1.5 Release Notes
Modification
Configuration Parameter
Description
Changed
up.25mm
User preferences parameter
Changed
up.analogHeadsetOption
User preferences parameter
Changed
up.backlight.idleIntensity
User preferences parameter
Changed
up.oneTouchVoiceMail
User preferences parameter
Changed
up.useDirectoryNames
User preferences parameter
Changed
up.welcomeSoundEnabled
User preferences parameter
Changed
up.welcomeSoundOnWarmBootEnabled
User preferences parameter
Changed
video.camera.frameRate
Video parameter
Changed
video.localCameraView.fullScreen.mode
Video parameter
Changed
video.maxCallRate
Video parameter
Changed
video.screenMode
Video parameter
Changed
video.screenModeFS
Video parameter
Changed
voIpProt.H323.dtmfViaSignaling
Call feature parameter
Changed
voIpProt.H323.enable
Call feature parameter
Changed
voIpProt.H323.local.port
Call feature parameter
Changed
voIpProt.SIP.local.port
Call feature parameter
Changed
voIpProt.SIP.outboundProxy.transport
Call feature parameter
Changed
voIpProt.SIP.specialEvent.lineSeize.
nonStandard
Call feature parameter
Changed
voIpProt.server.x.transport
Call feature parameter
Changed
voIpProt.server.dhcp.option
Call feature parameter
Changed
voice.audioProfile.Lin16.16ksps.payloadSize
Audio parameter
Changed
voice.audioProfile.Lin16.32ksps.payloadSize
Audio parameter
Changed
voice.audioProfile.Lin16.44_1ksps.
payloadSize
Audio parameter
Changed
voice.audioProfile.Lin16.48ksps.payloadSize
Audio parameter
Changed
voice.audioProfile.Lin16.8ksps.payloadSize
Audio parameter
Changed
voice.codecPref.iLBC.*
Audio parameters
Changed
voice.gain.rx.analog.*
Audio parameters
Polycom, Inc.
76
Polycom UC Software 4.1.5 Release Notes
Modification
Configuration Parameter
Description
Changed
voice.gain.rx.digital.*
Audio parameters
Changed
voice.gain.tx.analog.*
Audio parameters
Changed
voice.gain.tx.digital.*
Audio parameters
Changed
voice.handset.rxag.adjust.*
Audio parameters
Changed
voice.handset.sidetone.adjust.*
Audio parameters
Changed
voice.handset.txag.adjust.*
Audio parameters
Changed
voice.headset.sidetone.adjust.*
Audio parameters
Changed
voice.headset.txag.adjust*
Audio parameters
Changed
voice.ns.hd.*
Audio parameters
The parameter voice.ns.hd.enable has not
been changed
Changed
voice.ns.hf.signalAttn
Audio parameter
Changed
voice.ns.hf.silenceAttn
Audio parameter
Changed
voice.ns.hs.signalAttn
Audio parameter
Changed
voice.ns.hs.silenceAttn
Audio parameter
Understanding Updates to UC Software 3.3.2
This section lists additions and changes, removals, enhancements, and configuration file parameter
changes to UC software version 3.3.2 beside their respective Polycom tracking ID number.
New or Enhanced Features
56249 Added user confirmation on the phone before placing outgoing calls as part of the click to dial
behavior.
64548 Added missed-call synchronization. When local call lists are disabled on the phones, Missed calls
notifications are sent from the call server to the respective users.
66464 Provides simplified display option by removing protocol tag and host details (applies to VVX
1500D).
66466 When the parameter up.simplifiedSipCallInfo is enabled, the caller ID will not display the
host name for incoming and outgoing calls and the protocol information will not be shown.
66624 Geographical redundancy enhancements.
68836 Added support for Sennheiser EHS headset to the phone menus and configuration.
Polycom, Inc.
77
Polycom UC Software 4.1.5 Release Notes
70475 Extended the dialplan.digitmap String to support up to 100 from 30 segments.
Enhanced Capabilities
27469 Local Conferencing is no longer disabled if G.729 is in the Codec preference list (applies to
SoundStation IP 4000).
27777 The phone now plays a local hold reminder tone (applies to SoundStation IP 4000).
34454 If the microbrowser is enabled and it is refreshed too frequently and the pages contain large
images, the phone no longer locks up.
34743 A phone no longer freezes when it receives a check-sync if the resources on the phone are
heavily used by a downloaded wave files or by a large/complex microbrowser pages.
39630 When using the SoundPoint IP 330/320 phone with LCS2005, blocking a roaming buddy from the
privacy list no longer prevents the user from viewing the blocked buddy’s status.
45247 The SoundPoint IP 430 no longer reboot when viewing microbrowser pages and the internal
memory is being used for other function/operations.
47827 Voice Quality Monitor feature on SoundPoint IP now uses the correct units for Jitter in SIP
PUBLISH VQSession Reports.
49324 When dialing 99* from the phone with an integrated Polycom HDX, the * is no longer changed to
a dot on the HDX (applies to SoundStation IP 7000).
51904 When a Polycom HDX system is configured for SIP using UDP, it now makes a video connection
with the VVX 1500 phone.
52592 The phone now provisions when using the combined sip.ld file and a TFTP provisioning server
that does not support the bulk size option (applies to SoundStation IP 6000).
52782 Resolved some video issues that occur when VVX 1500 phones are bridged on Polycom HDX
and VSX MCUs.
55910 The phone no longer freezes/stops while preparing to boot up (applies to SoundPoint IP 430).
57838 When there is a call between two SoundStation IP 7000 phones along with a HDX system, the
HDX9004 system added a video call to HDX9002. There is no longer a hold between the
SoundPoint IP 7000 phones.
58177 When attempting to do a blind transfer from a PSTN line to an internal extension, three beeps are
no longer heard after pressing the Send soft key. Cancelling the operations enables the call
transfer.
60086 The SoundPoint IP 650 phones now send an Off-Hook or On-Hook notification when set to Auto
Answer.
60131 Reassignment of the speed dial keys now functions properly (applies to SoundStation IP 5000,
6000, and 7000).
60186 Call connection bandwidth between the HDX and VVX 1500 now synchronizes when the VVX
1500 is in CMA provisioning mode.
60255 A noticeable high-frequency flicker has been removed from the display when an update for BLA
remote hold/resume status occurs (applies to SoundPoint IP 650/670).
Polycom, Inc.
78
Polycom UC Software 4.1.5 Release Notes
60729 The phone now honors a BLA NOTIFY when the version number in the message body has
increased by more than 1.
60733 Can now establish a local conference bridge by using a speed-dial key, BLF line key or via call
lists.
60984 The dir.local.contacts.maxNum parameter no longer accepts 0 as stated in the
Administrators’ Guide; dir.local.contacts.naxNum accepts 1 to 99 OR 1 to 9999.
61013 On the VVX 1500, the Call Rate value can no longer be set higher than Max Call Rate value
when configured using the Web Configuration Utility.
61067 On the phone interface menu, pressing the Back soft key in the Authentication menu now
restores the menu title correctly.
61089 A pop-up no longer appears when adjusting the ringer volume while the call is on hold. Handsfree Volume no longer appears instead of Ringer Volume (applies to SoundPoint IP 320, 321,
330, 331, and 335).
61145 The dialplan.digitmap uses up to a maximum of 767 characters. The last character is no
longer truncated.
61147 The phone no longer reboots when a GET request is sent to the phone to
/TA/getParam?paramName=reg.1.ringType (applies to SoundPoint IP 331, 335, 450, 550,
560, 650, 670 and SoundStation IP 5000).
61316 The message waiting indicator on the VVX 1500 shows up on the correct line after the
registrations are moved to different line keys.
61955 An RTP audio delay is no longer detected when calling or receiving calls from a PSTN line.
62389 When the VVX 1500 phone is left idle for an extended period of time and a call is made between
the CMA users, the pop-up on the phone user interface is no longer delayed for both incoming
and outgoing H.323 calls.
62450 When the value in configuration parameter mb.idleDisplay.home is set to point to a URL with
an image, the phones idle display no longer shows a break in the border located at the bottom-left
corner.
62664 The VVX 1500 phones no longer drop the domain information when sending call setup to the
gatekeeper.
62675 Calls placed with the VVX 1500 using the URL dialing now show up in the missed calls list.
62687 Disabling local call forward now stops the phone from forwarding calls.
62974 Local call forwarding rules are now disabled when the feature is disabled.
63070 Call Forward CF messages such as Call Forward destination:Fwd:<number> now display when
DND is active.
63262 When using the SoundPoint 650 to dial a call using the Out of Dialog REFER based method, the
user no longer needs to press the Speakerphone key twice in order to terminate the call.
63277 During a call, a macro which is set to simulate a soft key press no longer displays an error
(applies to the VVX 1500).
63452 When URL dialing is disabled on the phone, transferring call initiated by BLF speed dial key no
longer prompts again for the URL.
Polycom, Inc.
79
Polycom UC Software 4.1.5 Release Notes
63746 During fail-back attempt, line icon shows as unregistered.
64036 Caller ID on the VVX 1500 now works properly when both Contact Directory Matching and
Chinese characters are enabled.
64190 Enhanced video quality during conferences with RMX 1500.
63850/64430
Initial dialog event NOTIFY after subscribe has the correct version.
64859 When a call is made using SRTP and TLS, the far end can now hear any audio even when the
SRTP packet sequence counter rolls over to zero.
64896 When Call Forwarding is on, the phone no longer updates the display before the server has
confirmed operation via NOTIFY.
65014 When a VVX 1500 phone is provisioned using CMA 5.3, LDAP directory searches now return
meeting rooms names when searching the CMA directory.
65207 Resolved a memory leak on the phones in specific call server environments when a call is
answered from a hunt group.
65288 When server side DND is enabled, an incoming call from a white list phone number can now be
picked.
65345/64862 One of the callers is no longer dropped when trying to set up a conference between PSTN
users.
65617 When Auto answer is enabled, the phone no longer sends a 180 response to the server.
65754 The XML string <key key.25.VVX 1500.function.prim=null/> no longer disables the Menu soft key
or the Menu hard key (applies to the VVX 1500).
65758 An extra space has been removed from each side of an umlauted character in the microbrowser
idle display: G Ä rtner instead of GÄrtner.
65979 The SoundPoint IP phone quick setup menu user name entry has been set to numeric characters
as the default.
66027 When the phone lock feature is enabled, trying to dial any number will no longer dial the
emergency number.
66106 When a call is made from the phone from the dial pad and pressing the speakerphone key it
correctly selects line 2 instead of line 1.
66217 Directed Call Pick-up soft key now works properly (applies to the SoundPoint IP 650 and VVX
1500).
66554 During a video call on the VVX 1500, the phone no longer drops video momentarily when there
are periodic offer less re-invites/ session refresh messages from server.
66593 When trying to dial an extension of four digits by pressing only two digits, a prompt displays on
the phone to enter more digits. After entering the other two digits, it no longer appends to the
earlier two digits thereby resulting in a failed call (applies to SoundPoint IP 3xx running UC
software3.3.x).
66621/66619 Created configuration parameters that allow phones to perform fail-over when a 503
response is received.
66625 The phone no longer sends three extra registration requests to primary proxy during fail-over.
Polycom, Inc.
80
Polycom UC Software 4.1.5 Release Notes
66626 DNSTTL no longer counts down during fail-back that fails. TTL is reset after re-registering to
secondary.
66666 The SoundStation IP 7000 phone is now being provisioned via FTP when the Windows 2003
server path MTU Discovery is disabled.
66964 Local call forward behavior is now working, as mentioned in the Admin Guide for the parameter
voIpProt.SIP.serverFeatureControl.localProcessing.cf .
67455 The phone no longer crashes during registration with TLS (applies to SoundPoint IP 650/670).
67622 The phone displays the correct caller name in the user interface where there is a call from a
group pickup number.
67633 Added support for the Zero-Touch Provisioning (ZTP) feature. Note that feature should not be
enabled unless the phone has been registered for use with the associated provisioning system
offered by your service provider.
67641 Pressing the Directory soft key on the VVX 1500 phone no longer redirects to the Advanced Find
screen automatically.
67642 When using the VVX 1500 to dial contacts from the corporate directory for which the dialing
entries are not filled appropriately, the phones no longer displays the attributes and no longer
skips null values.
67753 The phone no longer plays ringback after the call is timed out.
67867 The phone seizes the correct line after transferring an incoming call to the line when going offhook.
67966 When a call is made between two VVX 1500s the answering VVX 1500 which comes up after first
reboot no longer plays a noise pattern on the screen before playing video.
68063 The phone no longer reboots when DHCP failover occurs.
68195 Directed Pickup using star codes, for example, *200,*300 now works on the SoundPoint IP 650.
68267 When the BLF feature is enabled on the SoundPoint IP 650 and there is an active call, a ringtone
heard in low sound within the handset has been removed.
68344 Request Validation feature no longer rejects requests from another (second) server listed in the
configuration files.
68376 The VVX 1500 phone no longer reboots when the DND button is pressed repeatedly during the
idle state.
68382 The phone shows the correct time when the IP address on the NTP server is 12 digits.
68446 The parameter call.hold.localReminder.startDelay value is now honored when the
value is less than 60 seconds.
68476 The SoundPoint IP 331 phone is now bootable when set with Option 60, ASCII String and DHCP
Server Option 43.
69166 Placing a call is on hold in which RFC 3264 directionality attributes are present no longer results
in failure of terminating music on hold session.
69421 The VVX 1500 phones no longer fail to pass special character $ in the password via DHCP
Option 66.
Polycom, Inc.
81
Polycom UC Software 4.1.5 Release Notes
69671 The phones accept VLAN ID from DHCP option 129.
70027/62203
Conference with Genband CS2000 now works properly.
70988 The SoundPoint IP 550, when powered by external AC power, no longer reboots when certain
audio plays on full volume.
70233 When URL dialing is disabled, the user is no longer prompted for a URL when attempting to
transfer calls after using directed call pickup of a monitored BLF line.
70317 During an active IVR call, if there is a second incoming call to the same line, the phone now
sends DTMF.
70456 The SoundPoint IP 450 phones now show the complete text on the microbrowser screen.
71071 The inbound caller ID on the SoundPoint IP 33x now displays for new calls during an active call
on the phone. Observed this in version 3.2.5 and 3.3.1
71328 Modifying the phone username via phone Web user interface no longer changes the password
from numeric values to ???? (four question marks).
71947 When the phone lock feature is enabled on the SoundPoint IP 650, outbound calls can no longer
be dialed using line key, handset, headset and speakerphone key.
72766 When the configuration parameter device.set is set on the SoundPoint IP 650/670 with a new
boot server IP address, it now forces the phone to reboot.
Configuration File Enhancements
Refer to the following table for a list of enhancements made to the UC software version 3.3.2
configuration file parameters.
Table 13: UC Software 3.3.2 Parameter Enhancements
Configuration Parameter
Action
Property
Old Value New Value
call.clickToDial.referBased.
userConfirm
added
accessType
Admin
callback
DefaultCbNone
cfgParamType
param
default
0
help
call.shared.notifyTransferHold
AsActive
added
templates
sip-interop
type
Bool
accessType
Admin
callback
DefaultCbRestart
cfgParamType
param
default
0
help
Polycom, Inc.
max
1
min
0
82
Polycom UC Software 4.1.5 Release Notes
Configuration Parameter
device.prov.ztpEnabled
Action
added
Property
Old Value New Value
templates
hidden
type
Bool
callback
DefaultCbRestart
cfgParamType
param
default
help
device.prov.ztpEnabled.set
added
max
256
min
0
templates
device, site, new
type
String
callback
DefaultCbRestart
cfgParamType
param
default
0
help
dialplan.x.routing.server.y.transport
dialplan.routing.server.x.transport
dir.H350.dev.transport
dir.H350.group.transport
dir.H350.person.transport
Polycom, Inc.
changed
changed
changed
changed
changed
templates
device, site, new
type
Bool
enum
transport
max
256
min
0
type
String
enum
Enum
transport
max
256
min
0
type
String
Enum
default
TCP
enum
dirCorpTransport
max
256
min
0
type
String
Enum
default
TCP
enum
dirCorpTransport
max
256
min
0
type
String
Enum
default
TCP
enum
dirCorpTransport
83
Polycom UC Software 4.1.5 Release Notes
Configuration Parameter
dir.corp.transport
mb.main.toolbar.autoHide.enabled
pnet.joinOnAutoAnswer
Action
changed
added
added
Property
Old Value New Value
max
256
min
0
type
String
Enum
default
TCP
enum
dirCorpTransport
max
256
min
0
type
String
Enum
accessType
User, Admin
callback
CbMicroBrowser
cfgParamType
param
default
1
help
Enable/Disable
browser tool bar
auto hide feature
templates
applications
type
Bool
accessType
Admin
callback
DefaultCbNone
cfgParamType
param
default
0
help
reg.x.outboundProxy.failOver.
onlySignalWithRegistered
added
templates
video-integration
type
Bool
callback
CbReg
cfgParamType
paramArray
defaultAll
1
help
reg.x.outboundProxy.transport
reg.x.server.y.failOver.onlySignal
Polycom, Inc.
changed
added
numReplace1Ma
x
Const_NumLine
Reg
templates
reg-advanced
type
Bool
enum
transport
max
256
min
0
type
String
callback
Enum
CbReg
84
Polycom UC Software 4.1.5 Release Notes
Configuration Parameter
Action
WithRegistered
Property
Old Value New Value
cfgParamType
param2DArray
defaultAll
1
help
reg.x.server.y.transport
sec.srtp.newContextOnResume
changed
added
numReplace1Ma
x
Const_NumLine
Reg
numReplace2Ma
x
Const_NumServ
ers
templates
site
type
Bool
enum
transport
max
128
min
0
type
String
Enum
callback
DefaultCbRestart
cfgParamType
param
default
1
help
up.simplifiedSipCallInfo
added
templates
hidden
type
Bool
accessType
Admin
callback
DefaultCbNone
cfgParamType
param
default
0
help
voIpProt.SIP.dialog.strictVersion
Validation
added
templates
new
type
Bool
accessType
Admin
callback
CbSipStack
cfgParamType
param
default
1
help
voIpProt.SIP.failoverOn503Response
Polycom, Inc.
added
templates
new
type
Bool
callback
CbSipStack
cfgParamType
param
default
1
85
Polycom UC Software 4.1.5 Release Notes
Configuration Parameter
Action
Property
Old Value New Value
help
voIpProt.SIP.outboundProxy.failOver.
onlySignalWithRegistered
added
templates
sip-interop
type
Bool
callback
CbReg
cfgParamType
param
default
1
help
voIpProt.SIP.outboundProxy.transport
voIpProt.SIP.serverFeatureControl.
missedCalls
changed
added
templates
sip-interop
type
Bool
enum
transport
max
256
min
0
type
String
Enum
accessType
Admin
callback
DefaultCbRestart
cfgParamType
param
default
0
help
voIpProt.server.x.failOver.onlySignal
WithRegistered
added
templates
sip-interop
type
Bool
callback
CbReg
cfgParamType
paramArray
defaultAll
1
help
voIpProt.server.x.transport
voice.gain.rx.digital.headset.IP _330
changed
added
numReplace1Ma
x
Const_NumServ
ers
templates
sip-interop
type
Bool
enum
transport
max
256
min
0
type
String
Enum
callback
DefaultCbRestart
cfgParamType
param
default
-12
help
Polycom, Inc.
86
Polycom UC Software 4.1.5 Release Notes
Configuration Parameter
voice.gain.rx.digital.headset.IP _335
Action
added
Property
Old Value New Value
max
1000
min
-1000
templates
techsupport
type
SInt
callback
DefaultCbRestart
cfgParamType
param
default
-9
help
voice.gain.vol.ringer.gain.adjust
added
max
1000
min
-1000
templates
techsupport
type
SInt
callback
DefaultCbRestart
cfgParamType
param
default
-9
help
voice.headset.rxag.adjust.IP _335
added
max
1000
min
-1000
templates
new
type
SInt
callback
DefaultCbRestart
cfgParamType
param
default
-11
help
max
-11
min
-1000
templates
new
type
SInt
Understanding Updates to UC Software 3.3.1F
This section lists additions and changes, removals, enhancements, and configuration file parameter
changes to UC software version 3.3.1F beside their respective Polycom tracking ID number.
Enhanced Capabilities
Polycom, Inc.
87
Polycom UC Software 4.1.5 Release Notes
66743 The phones may be vulnerable to Denial of Service attacks when used in certain configurations.
Sending HTTP GET requests with a broken authorization header can produce a device restart
under certain circumstances in certain models of phones. For full details, refer to Technical
Bulletin 66743.
Understanding Updates to UC Software 3.3.1
This section lists additions and changes, removals, enhancements, and configuration file parameter
changes to UC software version 3.3.1 beside their respective Polycom tracking ID number.
New or Enhanced Features
50065 Added support to the VVX 1500 for CMA presence.
52476 Added support for Premium extensions to server synchronized ACD feature.
55061 Added support for the Team Function feature. This feature extends the compatibility of statically
configured Busy Lamp Field (BLF) to operate in a system requires the use of two URIs one for
call operations and another one to subscribe for notification of dialog events. It also provides
Ringing Indication and a Directed call pick-up capability in a system that does not generate RFC
4235 compliant dialog-info+xml documents.
58888 Added the ability to trigger a reboot (or configuration update) from the microbrowser. For
example, <softkey index=3 label=Reboot action=Action:UpdateConfig />
59000 The phones now ignore BLA dialog documents (via NOTIFY) that are reflected to User Agents
that are party to the dialog.
60306 The server certificate Serial Number SN is now verified against the server/proxy’s A record
domain names if the SRV record domain does not match the SN.
61343 The phones now provide a configurable parameter that allows the verification of the
authentication tag to be disabled for received SRTP packets. The purpose of this is to allow
system administrators to resolve defects in other endpoints where the authentication tag is not
computed correctly. Supported parameter: sec.srtp.noAuthRxRTP
61389 During the 802.1x - EAPOL Logoff, the phone will recycle the LAN link (e.g. it will bring it down
and up in an interval of one second) upon detecting a PC link down event. This shall force the
802.1X switch to refresh the authorized port state and start to send request for identity challenge
messages. The associated configuration parameter is
sec.dot1x.eapollogoff.pcforcelanlinkreset with values 0 - Never recycle LAN link
and 1 - The phone will unconditionally recycle the LAN link upon detecting PC link down event.
61861 Corporate Directory LDAP initialization supports the bind authentication.
62115 The phones now display the full text strings of the Phone Lock feature (applies to SoundPoint IP
320, 321, 330, 331, and 335).
62259 The phones now display the Call Forward destination on Idle Display.
62775 The toolbar slide-out option is now configurable on the VVX 1500. The associated configuration
parameter is mb.main.toolbar.autohide.feature
1 feature is enabled (default)
Polycom, Inc.
88
Polycom UC Software 4.1.5 Release Notes
0 feature is disabled. The Autohide enable/disable buttons are no longer visible to the user in
the toolbar.
Enhanced Capabilities
44337 Configured characters ;, /, ?, &, =, ~, %, \ are now escaped in INVITE messages.
55794 The SoundStation IP 6000 and 7000 phones no longer reboot upon receiving a call with incorrect
SRTCP indices.
56491 As of SIP 3.2.x, the screen no longer displays the IP address of the server when disabling the
Call Forwarding feature using a # code.
59824 The phone now changes all of the menu option labels into the selected language.
59843 On the VVX 1500, the caller ID correctly displays during an active call after switching
(exchanging) valid logon credentials between two phones.
60015 The phone no longer sends RTP media for 2.4 seconds after call is declined with 603 Decline.
60175 When using the Contact Directory speed dial, the left and right arrow keys no longer increment
and decrement the index unexpectedly (applies to SoundPoint IP 320, 321, 330, 331, and 335).
60514 The user password can now be changed by an administrator if the old password is unknown.
60572 An EFK soft key no longer requires at least one valid entry in <efk.efklist /> configuration in order
to be enabled.
60645 The VVX 1500 phone no longer resets to previous values in the Edit contact menu when the
mode is changed from Tel to Url.
60761 The Transfer and Conference soft keys on the SoundStation IP 5000 and 6000 are no longer
absent upon the 8th active outgoing call.
60788 When operating with a sip X server, there is now music on resume from a double Music On Hold
(MOH) between two phones.
60814 The Login soft key on the SoundStation IP 7000 now displays when
feature.acdLoginLogout.enabled is set.
60831 Ringback tone no longer continues to play for 30 seconds after the SoundStation IP 6000 phone
sends a BYE message.
60848 After invoking the Update Configuration menu option, the phone now returns to the idle screen.
60897 The Custom Ringer Types menu no longer uses the file name rather than configured name.
61030 The Buddy Watch presence now works on the VVX 1500 phone after it boots initially with
voIpProt.H323.enable=1.
61031 Active call now has a timer when attempting to transfer or conference the call (applies to
SoundPoint IP 450, 550, 560, 650, 670).
61041 The Call Server Configuration Menu now displays Options (1, 2, …) within the Menu items
(applies to the VVX 1500).
61042 The Directed call pick-up feature now works when the SUBSCRIBE message expires=0.
Polycom, Inc.
89
Polycom UC Software 4.1.5 Release Notes
61046 The Saved Certificate prompt is now shown when a new CA certificate is downloaded (applies to
SoundPoint IP 320, 321, 330, 331, 335, and SoundStation 5000 and 7000).
61088 The VVX 1500 phone no longer freezes and reboots after making a call with
tcpIpApp.port.rtp.forceSend=1024.
61090 The configuration parameter voIpProt.SIP.musicOnHold.uri is now updated after a
configuration change.
61095 While dialing a URL using the on-screen keyboard on the VVX 1500, the first entered character is
no longer unexpectedly deleted.
61102 The Handset or Speaker icon no longer appears instead of the Ringer icon when you adjust the
ringer volume while the SoundStation 500 and 6000 phones are idle.
61104 With a shared line configured on the VVX 1500 phone, activity on the remote shared line no
longer causes the idle browser content to cycle off then on.
61114 The VVX 1500 phone boots-up with the DHCP VLAN 256 DVD option.
61115 Can now answer calls after a configuration update is invoked.
61242 The configuration parameter voIpProt.SIP.useCompleteUriForRetrieve updates after a
configuration change.
61246 The voIpProt.SIP.allowTransferOnProceeding XML schema lists the correct type as
stated in the Administrators’ Guide.
61273 Joining calls into a local conference when 1 leg is a remotely held BLA line now maintains audio
between both remote users.
61314 The number of characters for custom names has been extended to 127 from 12.
61367 When dialing a number with a + sign, e.g. +492101099210, user=phone is now added to the To
header.
61677 The VVX 1500 phone no longer escapes the % character as %25 when is present in the
destination of a call.
61723 The VVX 1500 phone is no longer missing the first string <?xml version=1.0 encoding=utf-8 ?> in
FAST UPDATE requests.
61779 The phone no longer reboots spontaneously from the idle state or in-use state.
61904 A call is placed with the correct signaling protocol on the VVX 1500 when the line is configured as
dual line protocol.
62036 The SoundPoint IP 320 and 330 phones now send DTMF RTP EVENTS when receiving a
second incoming call during an active primary call.
62114 The user can now unlock the VVX 1500 phone after the phone is locked with a password
containing letters.
62325 Chinese characters no longer cause the VVX 1500 phone to become unresponsive to user
requests.
62333 The correct Chinese characters are displayed in the reboot menu on the VVX 1500.
62417 When an off-hook event is received from the headset base station, the phone no longer sends
three events to the base station in DHSG headsets and platforms.
Polycom, Inc.
90
Polycom UC Software 4.1.5 Release Notes
62453 The phone no longer displays a ghost call appearance labeled Unknown Party if a remote party is
held while the reorder tone is played locally.
62490 Enabling the Screen capture function with httpd.enabled=0 no longer causes the phone to
freeze and reboot.
62576 The phone now reboots in order to pick up new sip.ld file after an Update Configuration is
invoked from the menu.
62642 The phone no longer plays a dial tone and RTP media when resuming on a call held at another
phone.
62704 BLA presence now recovers properly on the monitoring phone when the LAN cable is
disconnected and then re-connected.
62906 The phone correctly provisions using the HTTPS protocol option when using a server certificate
with an older MD2 digest message algorithm.
63076 The phones with BLA lines are now able to establish more than 10 outgoing calls.
63214 The phone no longer reboots if it receives more REFERs that reg.x.callsPerLineKey is
configured for.
64742 Using a dial plan containing #, when a user goes off-hook and dials #1#2#, the phone now sends
out an invite message containing %231%232%23.
Configuration File Enhancements
Refer to the following table for a list of changes in configuration parameters. The list applies only to the
changes made since UC software 3.3.0.
The configuration files, their respective parameters and defaults, as well as the provisioning methods
have been simplified but extensively modified starting from UC software 3.3.0.
Before installing the software, it is highly recommended that you first familiarize yourself with the changes
outlined in the Administrators Guide for the Polycom® UC Software – 3.3.0 and Technical Bulletin 60519.
Table 14: UC Software 3.3.1 Parameter Enhancements
Configuration Parameter
Action
attendant.resourceList.x.callAddress
added
attendant.resourceList.x.proceedingIsRecipient
added
device.cma.disableTlsForDebug
added
device.cma.disableTlsForDebug.set
added
dir.H350.dev.bindOnInit
added
dir.H350.group.bindOnInit
added
dir.H350.person.bindOnInit
added
dir.corp.bindOnInit
added
Polycom, Inc.
91
Polycom UC Software 4.1.5 Release Notes
Configuration Parameter
Action
feature.acdPremiumUnavailability.enabled
added
reg.x.filterReflectedBlaDialogs
added
sec.dot1x.eapollogoff.pcforcelanlinkreset
added
sec.srtp.noAuthRxRTP
added
voIpProt.SIP.allowTransferOnProceeding
changed
Understanding Updates to UC Software 3.3.0
This section lists additions and changes, removals, enhancements, and configuration file parameter
changes to UC software version 3.3.0 beside their respective Polycom tracking ID number.
New or Enhanced Features
23335 Configuration parameter values can now be updated at run-time.
24111 Enhanced the user interface for selecting a distinctive ringtone associated with a contact in the
local directory. You can now review the ring name and play the ringtone before accepting and
associating the ringtone for specific contacts.
23394 Configuring parameters are now self-contained (default parameter values) and the configuration
process is more fault-tolerant.
35245 Line key behavior (configurable) has changed such that keys can now be used to hangup/terminate calls as well as establishing calls. The associated configuration parameter is
up.lineKeyCallTerminatetype=Booldefault=0 min=0 max=1.
38826 Added configuration parameters to expand the range of ports as well as to randomize port
selection for the purpose of downloading configuration files to the phone using TCP connections.
48138 Added support for dynamic support of G.729AB and iLBC codecs. G.729AB / iLBC (applies to
SoundPoint IP 320, 321, 330, 331, 335, 450, 550, 560, 650, 670).
48526 Simplified selection of codec configuration preferences. See Technical Bulletin 60519 for more
information. This change is not backward compatible to configuration files used with previous
software releases.
48690 Added the ability for users to lock the phone and restrict its access from unauthorized users.
Users must enter a PIN in order to access and use the phone. Refer to Quick Tip 57215 for more
information regarding this feature and configuration.
49658 Added configuration parameter to allow the phone to obtain Caller ID from the From header
instead of the P-Asserted-Identity segment. The associated configuration parameter is
voIpProt.SIP.CID.sourcePreference = P-Asserted-Identity, Remote-Party-ID, or From.
50067 Local contact directory now matches the Polycom CMA products style and user experience.
50151 Removed redundant levels of abstraction associated with arrays in configuration files.
Polycom, Inc.
92
Polycom UC Software 4.1.5 Release Notes
50644 Enhanced the visual indicator of incoming calls on the VVX 1500 for the hearing impaired. Upon
receiving an incoming call, the phone will ring and the display will flash on and off with a bright
orange and white screen. This visual indicator can be seen even when the display is viewed at an
indirect angle. The associated configuration parameter is up.accessibilityFeatures=1.
51121 RAM disk configuration parameters have been optimized.
51314 Added a configuration option to allow for minimal latency in order to meet JITC requirements. The
associated configuration parameter is voice.txPacketDelay. Normal or NULL (default) = no
change to Tx latency; low = low delay
51523 Added the ability to scroll horizontally caller ID information (if it is truncated when the number of
characters in the caller ID string exceeds the capacity of the display).
51446 Added configuration parameters supporting TLS cipher suites.
51594 Digit map replacements no longer need to be reflected in the placed calls list.
51725 Added support for G.719 audio codec in H.323 calls (applies to VVX 1500).
51979 Added support for asymmetric audio codecs.
52253 Configuration parameter values modified by an administrator logon credential using the phones
Web server are not permitted to be altered by user level logon credentials.
52493 Added support for MD4 encryption key (OpenSSL).
52532 The phones no longer invoke a reboot during the uploading of override files as a result of an
unresponsive provisioning server (after a timeout).
52864 Enhanced the user experience of confirming a Local Directory Search (applies to SoundPoint IP
320, 321, 330, 331, and 335).
53021 Added support for NTLM version 2 authentication [via XMPP, LDAP and HTTP(s)] for use with
CMA.
53023 Edit fields have been expanded to display additional content (applies to VVX 1500).
53231 Added a configuration parameter to control the behavior of terminating a 3-way conference by the
conference initiator. Options now include either terminating all conference legs or allowing the
other parties to stay connected.
53417 Implemented a slider bar on the VVX 1500 for adjusting levels in various menu screens.
53703 Added the ability for phones to send an 802.1x EAPOL Logoff message on behalf of an attached
PC when the PC is disconnected from the data port.
53932 Presence and BLF is supported on Avaya CS2100 soft switches.
54037 Attempting a Transfer/Conf of a held party while in active call is now consistent with all phones.
54045 Registration parameters can now be modified and activated without requiring the phone to restart
or reboot.
54098 Added the ability to automatically upgrade the BootBlock section of the BootROM.
54167 The BootROM and application software versions may now be obtained by using the on-board
Web interface.
54301 A timestamp displays in Call Lists alongside the Caller ID.
Polycom, Inc.
93
Polycom UC Software 4.1.5 Release Notes
54308 The navigation keys can now be used as a spin box control (ability to select values using the up
and down arrow keys) for numeric fields (applies to SoundPoint IP 320, 321, 330, 331, 335).
54678 The phones can now be deployed with a pre-set language. This supports out-of-the box
localization.
54928 Added a new API Telephony Event (XML) which is sent to the attached application upon a
successful line registration with a PBX.
55028 The maximum size of the contact directory contact field has been increased to 128 to
accommodate complex dialing scenarios.
55040/57981 Added the ability for administrators to install custom device certificates. The administrator
can add private and public keys (certificate) via TLS links.
55068 Added support for Null Ciphers to be used with TLS Authentication.
55318 The Advanced LDAP Search screen now supports languages other than English.
55334 Added the ability for the tool bar on the VVX 1500 to hide automatically.
55490 The configuration Web interface has been expanded to include parameters associated with
security.
55508 When a precedence call is offered to the phone, it now rings with a corresponding precedence
ringtone.
55509 When a precedence outgoing call is initiated, a precedence style ring-back tone is generated.
55510 The DSCP Differentiated Services Code Point levels for standard and precedence level calls are
aligned.
55513 The current precedence level of a call is now displayed.
55546 The following diacritic letters and ligature are now supported (language option selection) and can
be displayed without having to change the character encoding scheme ä, ö, ü / Ä, Ö, Ü ß.
55745 The phones now generate a MLPP resource-priority Header based on the dialed number.
55985 The SoundPoint IP 7000 now displays the LogOut soft key when configured to be enabled.
56666/56668
Added dynamic codec switching.
56790 Enhanced the computation of jitter buffer parameters based on received Quality of Service QoS
and expected payload size values.
56944 Enhanced the ability for application developers to implement changes to the phone’s
configuration. Configuration parameters can be modified via the Web interface. The Enhanced
method also eliminates the need to reboot the phone in order to register the changes.
57504 A new Warble.wav file is available which can be configured as an audible ringer for incoming
calls. This file will generate a loud ringer tone for phones deployed in areas with a high ambient
noise background.
58103 The default maximum call data rate has been increased to 768 Kbps from 512 on the VVX 1500.
58156 The user video call rate setting parameter value options have been shortened on the VVX 1500.
58758 Enhanced the rendering performance of the browser on the VVX 1500.
Polycom, Inc.
94
Polycom UC Software 4.1.5 Release Notes
58764 Added the ability of uploading configuration files representing the phones current set of
configured parameter values to the provisioning server.
59307 Added a diagnostic menu option that enables the display of configuration file statistics.
60316 Added an option in the user interface that allows the user to invoke the phone to force it to reconfigure itself based on newly administered configuration file parameter values.
60353 Custom ring classes (se.rt) can now be set to a maximum value of 17.
60363 Custom ringer chords (tone.chord.ringer.spareX) can now be set to a maximum value of
19.
Discontinued Features
50200/53590 Removed configuration parameters that are no longer required for custom bit-mapped
graphic indicator icons.
56209 Removed support for the SoundPoint IP 430.
59917 Removed support for the animated idle display images (static idle display images are still
supported).
Enhanced Capabilities
33425 On the SoundStation IP 7000, users can now reply to instant messages.
42509 Can now invoke the speed dial list using the Up Arrow key when first call is kept on hold (applies
to VVX 1500).
43660 URL addresses on the SoundPoint IP 330 are now saved in the call list entry. When the phone
receives a URL call from SPIP @xxx.xxx.xxx.xxx, the phone now saves the incoming URL call
address into call list entry.
44034 On the SoundPoint IP 330, the cursor now blinks in hot dial prompt.
44278 The phone number now displays correctly on a line key when the number of digits exceeds 10.
44478 Configurable soft key features now work on the VVX 1500.
44889 The Polycom bitmapped logo now displays on the SoundPoint IP 330 idle screen.
45013 The phones no longer reboot after a check-sync request when a call is held and a new call is
initiated and then cancelled.
47135 Casing of current encoding indication at title bar now match corresponding soft keys on the VVX
1500.
47542 The URL entry field on the VVX 1500 allows for 32 instead of only 28 characters.
48228 The Contact Directory now has a functional <New Entry> option and a correct Navigation Cluster
Guide NCG while dialing (applies to SoundPoint IP 320, 321, 330, 331, and 335).
48257 The default background image on the VVX 1500 now displays after the following sequence of
events: select an image file, followed by selecting an invalid image (file not found) and select the
default background image.
48463 Can now view JPEG images with file extensions .jpe or .jfif (applies to VVX 1500).
Polycom, Inc.
95
Polycom UC Software 4.1.5 Release Notes
48701 The touch-screen no longer disables during keypad diagnostics (applies to VVX 1500).
48776 Scrolling in the Ethernet menu no longer causes the selected highlighted item to be positioned at
the bottom of the screen (applies to VVX 1500).
48840 Pressing the Slower and Faster soft keys no longer causes the update cursor to advance
immediately.
49331 Audio is no longer lost when disabling the hands-free mode while on a speakerphone call (applies
to VVX 1500).
50812 Changes to configuration options are no longer lost without warning if you exit from the Settings
menu without passing through confirmation dialog.
50855 An error message is no longer shown when a contact is saved with an empty contact number
(applies to SoundPoint IP 320, 321, 330, 331, and 335).
50920 The phones display a correct contact upon pressing the speed dial line key while editing the
contact entry (applies to SoundPoint IP 320, 321, 330, 331, and 335).
50922 Dial plan now applies after editing a call list item and attempting to dial the number.
50969 The language displayed for a Missed call notification now changes when the option is changed to
another language setting (applies to SoundPoint IP 320, 321, 330, 331, and 335).
50997 Upon pressing a line key, the phone now dials the stored hot dial number (applies to SoundPoint
IP 320, 321, 330, 331, and 335).
51152 Back arrow now works as back-space when in the Display and Touch Screen Diagnostics or
Media Statistics screens (applies to VVX 1500).
51237 In the Server Menu, the Server Password option no longer accepts digits instead of characters as
the default (applies to SoundPoint IP 320, 321, 330, 331, and 335)
51656 Interactive microbrowser will now timeout if mb.main.idleTimeout > 600.
51664 The VVX 1500 phone no longer enters LCD Power-down mode in 3 to 4 minutes instead of the
time set by powerSaving.userDetectionSensitivity.officeHours=0.
51669 After both SIP and H.323 Call Server parameters in Admin Settings are reconfigured on the VVX
1500, only one dialog method is now offered to exit. A reboot is no longer required.
51947 Can now delete the URL on the VVX 1500 by selecting it right-to-left and pressing the backspace
key.
51993 Cancelling the deletion of a contact no longer appends an ellipsis to that contacts entry in the list
(applies to SoundPoint IP 320, 321, 330, 331, and 335).
52212 The phone now restarts while another extension on a shared line is in use. The phone no longer
thinks it is active on a call.
52374 Options in the Forwarding menu are no longer appended with an ellipsis after returning from the
selected option.
52438 Typing in a fully filled field no longer prevent the cursor from advancing and overwriting existing
content (applies to SoundPoint IP 320, 321, 330, 331, and 335).
52447 After placing 21 encrypted calls on hold, the VVX 1500 phone no longer locks-up and reboots at
the 22nd multiple encrypted calls.
Polycom, Inc.
96
Polycom UC Software 4.1.5 Release Notes
52590 The Add Video soft key is no longer accessible when flashing the POTS line to make a second
POTS call. While playing dial tone for second POTS call, pressing the Add Video soft key and
dialing a video number no longer causes the HDX to lock-up and reboot (applies to SoundStation
IP 7000).
52629 The phones accept tel URIs as tel://number and tel:number.
52655 Upon disabling the directory, saving a contact from the corporate directory to the directory file no
longer causes the saved contact to reuse the speed dial index starting from 1.
52690 The Add Phone soft key no longer appears while the Call Type is set to Conference-SIP and the
phone is rebooted without a network connection (applies to SoundStation IP 7000).
52772 In the Corporate Directory, when sortControl=1, a quick search on multiple searchable
attributes no longer causes the entry list to display items that are not starting from the beginning.
52851 Cancelling the Directory Search configuration change no longer appends an ellipsis to menu item
label (applies to SoundPoint IP 320, 321, 330, 331, and 335).
52895 Enabling the Call Forwarding feature without entering a contact number no longer causes it to fail
(applies to SoundPoint IP 320, 321, 330, 331, and 335).
52896 The Forwarding status field in the Forward menu option screen now correctly corresponds to the
actual call forwarding status (applies to SoundPoint IP 320, 321, 330, 331, and 335).
52945 In the Corporate Directory, when performing a quick search, the Select/Submit indicator in the
Navigation Cluster Guide displays correctly.
53066 When hot dialing on the VVX 1500, the white screen no longer flashes after pressing the Dial soft
key, termination key, and dual line key.
53104 When an attempt to change the language option fails, the list of available language options are
now sorted correctly.
53447 Initiating a URL based hot-dial by pressing the # or * key on the VVX 1500 no longer causes an
invalid character to be inserted in the SIP URL.
53679 The Back soft key on the VVX 1500 is no longer always present in the APP menu screen.
53953 In the LDAP feature on the VVX 1500, the Scroll icons for navigating up and down pages now
display when the last contact in the search list is reached.
54131 The SoundStation IP 5000 phone now displays the Volume control while the ringer volume is
being adjusted in Quick Search mode.
54175 The Swedish Group soft key is no longer truncated; the visible portion translates properly.
54219 The phones can now establish a link when connected to some switches when both phone and
switch are configured for 100Mbits/Full Duplex (applies to SoundPoint IP 560 670).
54292 On the VVX 1500, the information in the Line status menu accurately reflects the Gatekeeper
address in use by the phone.
54343 Added the ability to save changes to text or IP entry fields while in the Admin Settings menu after
viewing the Web browser on the VVX 1500.
54356 The Delete key on the VVX 1500 does not dismiss the character selection control or prevents
character entry in the browser.
Polycom, Inc.
97
Polycom UC Software 4.1.5 Release Notes
54614 The VVX 1500, upon originating a conference call, no longer shows a blank black screen instead
of the No Video - crossed out camera image, while the call is on hold.
54616 When DND is enabled on the VVX 1500 on both SIP and H.323 lines, a SIP call no longer
generates a busy tone and an H.323 call will no longer generate a re-order tone.
54617 While listening to a fast busy tone, if an incoming call is offered, the speaker LED is no longer
turned off even though the fast busy tone is still present.
54638 Opening and closing the Web browser on the VVX 1500 no longer resets ABC/abc/123 and
encoding soft keys.
54656 The phone now displays an x/y indicator when multiple calls are active if the Time and date
display is disabled.
54720 Placing the handset on-hook no longer unexpectedly closes the Audio Diagnostics menu on the
VVX 1500.
54727 Invoking the Abc/ASCII entry mode on the VVX 1500 capitalizes entered letters properly in the
Corporate Directory search field.
54735 Upon pressing the VIDEO key on the VVX 1500, the focus now changes to Active Conference
pane.
54756 The VVX 1500 phone can display the dialing screen when an alpha character is configured and
entered into the contact field followed by a call to the specified contact.
54757 The Call Timer on the VVX 1500 displays a correct duration value.
54834 The VVX 1500 no longer connects with audio only when an MGC IVR Video Welcome Slide is
used.
54876 Inter-digit DTMF signaling interval now matches the tone.dtmf.offTime setting.
54949 An unassigned soft key no longer operates as a Dir soft key on the SoundStation IP 7000.
54966 The Lin16.16ksps codec now engages if it is the only supported codec.
54988 The user is now able to make additional changes to the selected item in the Prioritize Background
menu after making an initial selection (applies to SoundPoint IP 450, 550, 560, 650, and 670).
54993 The SoundStation IP 7000 phone no longer displays Enter name instead of Enter URL in the
Install Custom CA Cert menu.
54995 Pressing the # key while in an idle call state no longer displays the character in dial screen.
55001 The Backspace soft key no longer shows at left edge of a dialed SIP URL (applies to SoundPoint
IP 320, 321, 330, 331, and 335).
55002 The user is now able to press and hold the Backspace soft key to clear the contents of the dialing
fields (applies to SoundPoint IP 320, 321, 330, 331, and 335).
55005 The user Interface no longer becomes corrupted when change the language while hot-dialing
(applies to SoundPoint IP 320, 321, 330, 331, and 335).
55014 Soft keys no longer disappear from a shared line when a hold/resume operation is performed on
another remote shared line (applies to SoundStation IP 5000 and 6000).
Polycom, Inc.
98
Polycom UC Software 4.1.5 Release Notes
55017 Auto Reject now functions as expected when the feature is enabled through the Contact Directory
when an Alpha-character is present in the CONTACT field (applies to SoundPoint IP 320, 321,
330, 331, and 335).
55039 The Navigation Control Group (NCG) Indicator no longer shows the right-pointing arrow even
when there are no calls in the call lists.
55053 The Page up arrow now functions correctly when the Server menu is highlighted and the DHCP
client is set to disabled.
55063 It is no longer possible to select a disabled menu item using the * key, resulting in a nonfunctional Edit soft key.
55094 When taking the phone off-hook and dialing the # key, the # no longer displays in the Enter more
digits field (applies to SoundPoint IP 320, 321, 330, 331, and 335).
55129 The Transfer and Conference soft keys on the SoundStation IP 7000 now display upon an 8th
active call.
55139 The user can now view the full date when the phone is configured for Norwegian language Norsk
(no-no) (applies to SoundPoint IP 320, 321, 330, 331, and 335).
55271
The Please Enter a Contact pop-up no longer shows up unexpectedly when adding/editing
contacts.
55287 The phone no longer drops the incorrect call if the user selects (on the phone UI) a held call and
then attempts to terminate the active call (e.g. by placing the handset on hook).
55297 An audio and video conference call appears as a single video call (applies to the SoundStation IP
7000).
55313 The Routing soft keys on the VVX 1500 now display correctly when the Call Park feature is
enabled.
55339 Resuming a conference while running the Slide Show application on the VVX 1500 no longer
causes the user interface to become dysfunctional.
55340 The user can no longer launch picture frame on the VVX 1500 while a recording is in progress
causing the USB busy icon to disappear.
55375 The Outgoing Call control interface on the VVX 1500 now displays when the Speed Dial Contact
Enhanced Feature Key macro fails to execute.
55423 The correct soft keys and user interface displays on the VVX 1500 after exiting the screen that
was previously opened from the icon in the status bar; while hot dialing digits.
55457 When the dual protocol line is registered only to the gatekeeper and not to the SIP server on the
VVX 1500, this no longer causes hot-dialed SIP URL to call via H323 and dialog options to
appear when a hot dial URL call is attempted.
55477 SRTP Key renewal now occurs during local conference calls.
55478 DHCP VLAN Discovery (DVD) no longer reports as not active when it actually is.
55485 The Camera Settings Save soft key on the VVX 1500 no longer loses its context-sensitivity upon
second visit to the menu option.
55514 Calling into a Video Server on the VVX 1500 no longer causes the phone to connect the audio
portion of call but does not establish a video connection.
Polycom, Inc.
99
Polycom UC Software 4.1.5 Release Notes
55560 On occasion, the VVX 1500 phone no longer displays an incorrect call duration timer value while
on an H.323 call to an RMX-2000.
55641 The Y-axis auto-scaling of the Network Load graph on the VVX 1500 is now accurate.
55697 The phone no longer rejects calls with 486 if NOTIFY:Alerting is received before the INVITE
and reg.x.lineKeys and reg.x.callsPerLineKey is set to 1.
55644 The VVX 1500 now uses the correct routing protocol when dialing an LDAP contact from the onhook state via termination.
55907 On the VVX 1500, typing a or # no longer causes the on-screen keyboard to unexpectedly close
and discard any edits.
55911 Changing the text entry mode no longer causes the backspace soft key to disappear (applies to
SoundPoint IP 320, 321, 330, 331, and 335).
55929 Pressing the down arrow no longer affects a change on the Navigational Cluster Guide (NCG)
(applies to SoundPoint IP 320, 321, 330, 331, and 335).
55964 The VVX 1500 phone no longer seizes the only unregistered share line using the New Call soft
key, speaker and headset function key.
56046 The default value of the Sound Effect Destination parameter setting is now removed from the
override file when a new value is selected from the menu option.
56057 The phones no longer de-registered upon receiving a large number of NOTIFY messages for
watch buddy enabled contacts.
56147 Adding Contacts to the SoundPoint IP 550 and 670 that are longer than 10 characters or
numbers are no longer truncated on the idle screen.
56156 The abc/ASCII string no longer remains in the title bar on the VVX 1500 after leaving edit mode
for a menu item.
56161 Emergency numbers matched against dialplan.routing.emergency.x.value are now
sent to servers listed in dialplan.routing.emergency.x.server.y.
56168 When adding more than 7 characters and/or digits to a local contact directory entry on the
SoundPoint IP 450, the characters and/or numbers no longer overlap on the idle screen, when
they should be truncated.
56294 The Dutch_Netherlands localization now displays the correct default 24 hour time format in
SIP 3.2.x.
56289 Label text is no longer drawn past the edge of the speed dial label on the display next to the key
(applies to SoundPoint IP 550, 560, 650, 670).
56333 The SoundStation IP 5000 phone no longer reboots automatically when lease time expires after
disabling and enabling the DHCP server.
56334 The phone no longer plays a short burst of ringtone upon switching initiating a call sequence of
transfer, conference initiation, and then cancels.
56338 The SoundStation IP 7000 phone no longer reboots when the user presses the Manage soft key
during an 8-way MP call plus 1 audio EP conference.
56381 The conference phones now accept a DHCP offer that do include the terminating END (0xFF)
option (applies to SoundPoint IP 5000, 6000, 7000).
Polycom, Inc.
100
Polycom UC Software 4.1.5 Release Notes
56401 The Admin password length in the boot menu and Menu > Settings > Advanced menu now
match.
56678 Local contact directory entries now store up to 32 characters instead of only 31.
56708 The SIP URL dialing field accepts up to 32 characters instead of 256.
56787 The phone no longer plays a short tone while retrieving a parked call using an incorrect contact.
56788 The contact field of the local contact directory now accepts 128 characters instead of only 32
(applies to SoundPoint IP 320, 321, 330, 331, and 335).
56797 The SoundPoint IP 450 Admin Settings sub-menus correctly display the titles in a white
background box.
56809 The configuration parameter voice.audioProfile.Lin16.48ksps.payloadType has a
default value of 118 instead of 119.
56827 The soft keys associated with Conference Remote Pickup NewCall, Transfer, and Conf soft keys
on the SoundStation IP 7000 are no longer missing when the conference call is split.
56868 Published CDP power values in TB 48152 now match actual measured consumption.
57146 The phone no longer freezes and reboots when it receives an INVITE message with special
characters in the FROM header and the call is placed on hold.
57368 The second contact in the Local Contact Directory on the SoundStation IP 5000 is no longer
highlighted when it is selected.
57369 The Contact entry in the Local Contact Directory no longer takes a long time to display (applies to
SoundStation IP 6000 and 7000).
57398 The phone no longer displays Please enter a contact pop-up message after adding a contact in
the local contact directory.
57443 The display on the SoundStation IP 6000 and 7000 no longer flickers while making an outgoing
call.
57597 Using the VVX 1500 phone with an HDX, the phone now transmits video upon resuming a SIP
call.
57615 The Autohide feature on the VVX 1500 now functions when PIN is pressed while the tool bar is
sliding down out of view.
57849 The phone now acquires the correct VLAN using LLDP after a bootup.
57863 The phone accepts a DHCP END (0xFF) option in a DHCP INFORM response.
57958 In the fail-over feature, while re-registering, there is no longer a 32 second delay before sending
INVITE to the third server.
58023 A call into a 3COM VCX audio conference server when using the VVX 1500 no longer causes the
phone to reboot.
58172 Hot-dial numbers no longer disappear from the screen if there is an incoming call during the
outgoing hot-dialing state (applies to SoundStation IP 5000 and 6000).
58197 After upgrading from 3.0.0 to 3.1.3 Rev C, there is no longer a delay in the audio signal when
answering a call using the speakerphone.
Polycom, Inc.
101
Polycom UC Software 4.1.5 Release Notes
58296 H.323 digit-map no longer routes files when the reg.1.lineKeys configuration parameter has a
value of greater than 1 and reg.1 is assigned a SIP number (applies to VVX 1500).
58362 Initiating a URL hot-dial call by pressing the # or * key on the VVVX 1500 no longer causes the
Enter URL dialog to pop-up with the # character already inserted into the field, even though the #
character is not a valid SIP URL character.
58464 A Contact can now be saved from a Corporate Directory search result into a local directory. This
is as a result of not checking the correct attribute such as SIP vs. H.323.
58498 Within the re-registration on fail-over feature, Subscribe now triggers the fail-over. The phone now
sends the register request to the second server after received an ICMP from the primary server.
58509 Within the Re-registration on failover feature, the phone no longer sends an extra Register
request to primary server after the first fail-over.
58520 Resolved a uni-directional Video Streaming interoperation issue with Siemens Video Desktop
Client ODC (applies to VVX 1500).
58574 The SoundPoint IP 650 phone now validates an existing registration when it is registered with a
BroadSoft server.
58619 The line no longer becomes unregistered when an invalid name and password is entered from
the menu options on the phone. The line becomes unregistered until the phone is rebooted.
58782 The phone sets the Call Control 802.1Q Priority correctly when using TCP. The value is set
correctly when using UDP.
58785 The VVX 1500 phone now appends the MAC address to HTTP user agent headers when
configured to do so.
58787 The VVX 1500 phone no longer reboots immediately after making a call to an RMX when the
Camera Target Frame Rate is set to minimum.
58874 When using TCP preferred transport, the phone now resends a 200 OK message after answering
a call without receiving an ACK.
58906 The phone now clears its BLA state table when receiving a NOTIFY message with state = full
after a SUBSCRIBE message.
58907 The VVX 1500 phone now sends an INVITE SIP packet when the configuration parameter
msg.mwi.1.callBack=voicemail and the user presses the Messages key.
58908 With BootROM 4.2.1.0334, the VVX 1500 phone no longer sends a truncated Option 60
message.
58913 The phone no longer reboots when pressing the Messages key while Message Waiting Indicator
is disabled. When the phone has more than one registration and
msg.mwi.1.callBackMode=disabled and msg.mwi.2.callBackMode=disabled, the
phone no longer freezes when the Messages key is pressed. The phone will no longer respond to
any further key presses.
59129 The Centralized Conference feature no longer fails when a URI is incorrectly assigned to
voIpProt.SIP.conference.address.
59262 A conference notification no longer causes the phone to lock-up and then reboot.
59308 A retransmitted INVITE message no longer results in a 400 response.
Polycom, Inc.
102
Polycom UC Software 4.1.5 Release Notes
59430 Calls received from a mobile to the VVX 1500 no longer cause the phone to display SIP +86…@.
The @ should not be displayed.
59561 The VVX 1500 phone no longer displays an incorrect time after the configuration parameter
tcpIpApp.sntp.daylightSavings.enable is set to disabled.
59737 The Line Label now displays on the top line of the screen when using the HTML idle display
micro-browser page (applies to SoundPoint IP 320, 321, 330, 331, and 335)
59777 When using NN# speed dial feature, the title no longer displays Directory instead of Speed Dial
(applies to SoundPoint IP 320, 321, 330, 331, and 335).
59949 Idle bitmap graphic is no longer displayed on the bottom of the screen so that only half of the
display is utilized when ind.idleDisplay.mode=2 or 3 (applies to SoundPoint IP 320, 321,
330, 331, and 335).
59954 The phone no longer locks up and reboots when a Re-INVITE message within same dialog is
sent to the phone immediately after sending a CANCEL message for the initial INVITE.
59967 When an incorrect CA certificate is installed, the phone will not attempt to retry a TLS handshake
(applies to LDAP on the VVX 1500).
60013 The phone no longer locks up and reboots when accessing the contact directory if
dir.local.readonly=1 (applies to SoundPoint IP 320, 321, 330, 331, and 335).
60126 Gateways no longer reject an INVITE message when reg.1.csta=1. The INVITE includes the
header Acceptapplication/sdp/application/csta+xml.
60145 The SoundPoint IP 650 phone now correctly presents 2 BLA call appearances. The 2nd call
appearance now correctly indicates a remotely held line, when it is not.
60264 When a BLA line is showing the dialing screen, remote call appearances no longer display when
the remote BLA line resumes a call (applies to SoundPoint IP 450, 550, 560, 650, and 670).
60266 When a phone is in dialing screen, if a remote SCA/BLA line holds and resumes, the dialing icon
no longer changes between the animation arrow and the termination (speaker) icon. The
termination icon displays continuously and no longer changes (applies to SoundPoint IP 320,
321, 330, 331, and 335).
60267 Can now change a checked item twice in the Prioritize Background menu (applies to SoundPoint
IP 550, 560, 650, and 670).
60340 The Join soft key on the SoundPoint IP 650 no longer displays on a phone with a BLA line when
there is only one call on the phone.
60650 The idle browser on the VVX 1500 no longer alternates between current content and earlier
content when it the display is refreshed.
62621 SoundPoint IP 321 and 331 phones running SIP 3.2.3.3122 and configured for HTTPS no longer
display the error messages Alert: Fatal, Description, Decode Error.
Configuration File Enhancements
Note that the configuration files, their respective parameters and defaults, as well as the provisioning
methods have been simplified but extensively modified compared to previous releases.
Polycom, Inc.
103
Polycom UC Software 4.1.5 Release Notes
Before installing the software, it is highly recommended that you first familiarize yourself with the changes
outlined in the Administrators Guide for the Polycom® UC Software – 3.3.0 and Technical Bulletin 60519:
Simplified Configuration Enhancements in Polycom® UC Software 3.3.0.
Understanding Updates to SIP 3.2.5
This section lists additions and changes, removals, enhancements, and configuration file parameter
changes to SIP 3.2.5 beside their respective Polycom tracking ID number.
New or Enhanced Features
59000 The phones now ignore BLA dialog documents sent within NOTIFY messages that are reflected
to User Agents that are party to the dialog.
62939 Various enhancements to the Geo-Redundancy (multiple server fail-over support) feature. For full
details, refer to the list of documents in Reference Documents.
64359 Bridged Line Appearance BLA line dialog rendering is now converted from No to Yes on User
Agents that are a remote party to the dialog.
Enhanced Capabilities
54219 The SoundPoint IP 560 and 670 phones now establish a data link when connected to some
switches when both phone and switch are configured for 100Mbits/Full Duplex.
57570 A fail-over is now performed as a result of a SIP Response code 503.
60851 Dialing using the Speaker or Headset key no longer drops the initial call appearance.
60973 Entering a username and password using the Quick Setup (QSetup) soft key followed by a
request to save, now automatically invokes the phone to reboot the phone in order to the changes
to be applied.
61248 After configuring a phone with 3 line registrations, while the 2nd line is on hold, if a user hot-dials
using the speaker/headset termination key, the phone no longer inadvertently seizes line 3 to dial
out.
61283 The phone no longer incorrectly sends a NOTIFY with <param pname=+sip.rendering pvalue=no
/> when a user attempts to place a conference call on hold and the phone receives a 400 Bad
request.
61541 When a user attempts to place a conference on hold and the phone receives a 400 Bad request,
the phone correctly sends a NOTIFY with I=no. This no longer causes the incorrect presence, on
the other Bridged Line Appearance line, to be displayed.
62206 The phone no longer displays Service Unavailable upon lifting the handset and pressing the Line
2 key (applies to SoundPoint IP 320, 321, 330, 331, and 335).
62226 The phones no longer join a conference after receiving a 403 Forbidden from the switch.
62383 A held call on a Bridged Line Appearance with remote phones is now presented (applies to
SoundPoint IP 601).
Polycom, Inc.
104
Polycom UC Software 4.1.5 Release Notes
62567 SoundPoint IP 3xx phones monitoring each other in a 2x2 BLA configuration are now able to pick
up held calls.
62621 SoundPoint IP 3xx phones configured for HTTPS no longer display the error messages Alert:
Fatal, Description, Decode Error.
62642 The phones no longer play a dial tone as well as RTP audio when resuming a call held at another
phone.
62643 When the user presses both line keys (Line 1-hold and Line 2-Active call) simultaneously on the
SoundPoint IP 3xx, the active call on Line 2 is no longer dropped.
62669 Multiple phones no longer try to resume a held Bridge Line Appearance BLA line at the same
time.
62672 Directed Call Pickup DCP or Group Call Pickup feature (using soft keys instead of *53 and *54
feature access codes) no longer fail when the user enters an account code. The account code is
not appended to the user portion of the URI.
62855 Invoking either the Group Call Pickup or Directed Call Pickup feature, using its corresponding soft
key, now functions properly. The display shows Unknown and the call is not picked up (applies to
SoundPoint IP 3xx).
62902 The phone now accepts inbound SIP requests from an RROFO (Geo-redundancy) server that is
not registered with that phone.
62926 The Resume soft key on the SoundPoint IP 3xx is now presented when the line key is pressed
continuously while the line is in a remote held call state. This occurs when the line is configured
as callsPerLineKey=1.
63099 The phones monitoring Bridged Line Appearance BLA line, configured for one call per line, can
now pick up the held call after the call on a BLA line has been put on hold using the
Transfer/Conference key.
63280 Regarding Geo-redundancy RROFO, calls on hold are now released when pressing the Resume
soft key after the IP BE fail-over occurs while using the geo-redundancy feature. The user no
longer needs to press the End Call soft key to complete the intended result.
63388 If a phone’s SIP lines are not registered with a call server, and the Emergency Call Routing
Feature is enabled (by configuring the dialplan.routing.emergency.x.value and
dialplan.routing.emergency.x.server.y parameters) dialing the configured
emergency number will now work when you use on-hook dialing and when URL Dialing is
enabled.
63536 The Redial feature functions correctly after invoking an outgoing call accompanied with an
account code.
63631 The counting down aspect of the Geo-redundancy RROFO-DNSTTL feature no longer fails
during fail-back. The Time-To-Live TTL timer should be reset after re-registering to the secondary
server.
63704 Regarding Geo-redundancy RROFO, the phone no longer sends three extraneous registration
requests to the primary proxy server during a fail-over.
64093 Regarding Geo-redundancy RROFO, a fail-over using either the Conference or Transfer feature
now stops a consultative call when the primary call is terminated.
Polycom, Inc.
105
Polycom UC Software 4.1.5 Release Notes
64212 Invoking the Call Park feature on the SoundPoint IP 3xx with the soft key now functions correctly
when the soft key is configured as 1 line and 1 call per line.
64219 The SoundPoint IP 3xx phone sends a proper hold NOTIFY message after a consultative transfer
is canceled when the configuration parameter notifyTransferHoldAsActive is disabled.
64274 In an attempt to resume a held call, the held call is no longer terminated when the user
inadvertently seizes two line keys simultaneously.
64327 In an attempt to answer an incoming call, the user no longer inadvertently presses 2 line keys.
The user is no longer connected to both lines one with an incoming caller and the other with dial
tone.
64340 The indicator, on a Bridged Line Appearance BLA line that is monitoring other lines, no longer
remains on continuously after the monitored phone performs the following sequence transfer >
split > endcall > resume > hold.
64356 The display on the SoundPoint IP 3xx showing a remote call appearance now times out properly
when the user presses continuously a BLA line key followed by pressing a down arrow key while
there are multiple calls on hold on the remote BLA.
64360 The state of the indicator of a BLA line appearance is now properly reported after the phone
receives an INVITE containing replaces.
64762 When special characters in the FROM field are received, they no longer prevent the SoundPoint
IP 430 phone from displaying Caller ID information.
64862 Joining an internal extension with an external PSTN call no longer causes one call to drop.
65119 When a Bridged Line Appearance BLA line is presented in a dialing screen, the remote call
appearance now displays when the remote BLA line resumes a call.
65207 A slow memory leak no longer occurs in the SIP stack due to the receipt of hunt group INVITE
containing replaces with phones using ADTRAN switches.
65368 When the configuration parameter signalWithUnregistered=0, the phone now always
ignores all of the messaging traffic.
65842 Call waiting tone no longer continues to play after an inbound call has been forwarded and
answered by the PSTN.
67178 Centralized conference can now be established when reg.1.lineKeys is 5 or greater (applies
to all SoundPoint IP).
Configuration File Enhancements
Refer to the following table for a list of enhancements made to the SIP 3.2.5 configuration file parameters.
Table 15: Software Version 3.2.5 Parameter Enhancements
File
Change
Configuration Parameter
Old Value
New Value
phone1
added
reg.n.server.m.failOver.onlySignalWith
N/A
Null
Registered
Polycom, Inc.
106
Polycom UC Software 4.1.5 Release Notes
File
Change
Configuration Parameter
Old Value
New Value
phone1
added
reg.n.outboundProxy.failOver.onlySignal
N/A
Null
WithRegistered
phone1
added
reg.n.filterReflectedBlaDialogs
N/A
Null
sip
added
voIpProt.server.n.failOver.onlySignalWith
N/A
Null
Registered
sip
added
voIpProt.SIP.CID.sourcePreference
N/A
Null
sip
added
voIpProt.SIP.failoverOn503Response
N/A
1
sip
added
voIpProt.SIP.outboundProxy.failOver.only
N/A
Null
N/A
1
SignalWithRegistered
sip
added
call.localConferenceEnabled
Understanding Updates to SIP 3.2.4B
This section lists additions and changes, removals, enhancements, and configuration file parameter
changes to SIP 3.2.4B beside their respective Polycom tracking ID number.
Enhanced Capabilities
66743 The phones may be vulnerable to Denial of Service attacks when used in certain configurations.
Sending HTTP GET requests with a broken authorization header can produce a device restart
under certain circumstances in certain models of phones. For full details, refer to Technical
Bulletin 66743.
Understanding Updates to SIP 3.2.4
This section lists additions and changes, removals, enhancements, and configuration file parameter
changes to SIP 3.2.4 beside their respective Polycom tracking ID number.
Enhanced Capabilities
59308 A retransmitted INVITE message causes a 400 Bad Response reply. This is in violation of RFC
3261 section 17.2.1.
65207 A consistent but slow memory leak occurs as a result of receiving INVITE messages containing
replaces.
65435/65725 With reference to IEC 60268-1, the default and maximum values for the headset and
headphone audio levels have been adjusted to ensure compliance with the IEC 60268-1 TUV
safety requirements (applies to SoundPoint IP/VVX 1500).
Polycom, Inc.
107
Polycom UC Software 4.1.5 Release Notes
65660 The BootBlock may become corrupted as a result of accessing unprotected section of flash
memory.
Understanding Updates to SIP 3.2.3
This section lists additions and changes, removals, enhancements, and configuration file parameter
changes to SIP 3.2.3 beside their respective Polycom tracking ID number.
New or Enhanced Features
43099 Added support for the SoundStation IP 5000 conference phone.
43297 Sound effects can now be played out of a destination based on user configuration. The available
destinations are: chassis, handset, headset or active. The default is chassis.
45462 All SoundPoint and SoundStation phones now comply with retry-after instructions embedded in
SIP Response codes 500 and 503 as part of REGISTER and other requests.
50739 On a multi-leg conference on the SoundStation IP 7000, when the End Call soft key or the On
Hook hard key is pressed, the conference phone will ask the user if the entire call should
terminate. A negative response will guide the user to the conference manage menu to allow the
user to terminate the individual legs of the call. The dialog only appears for multi-leg conference
calls.
51753 Enhanced the appearance on the SoundPoint IP 450 of anti-aliased characters.
51940 All SIP phones now have a fail-over feature that enables phones to re-register before diverting
SIP signaling to an alternate server. This feature will be formally released and documented in a
future release.
54041 Format of DHCP Option 60 Data is now configurable and added support for Option 125 as per
RFC 3925.
54983 Internal IP address of the VVX 1500 phone (instead of an alias) is no longer being sent in the
Facility Message.
55524 Logs no longer display Cant set 802.1Q VLAN ID for TCP protocol messages at default when
running on a VLAN.
56272 Network Configuration DHCP sub menu now supports Option 60 format. The new options include
setting either RFC 3925 Binary [default] or ASCII String.
Enhanced Capabilities
45188 The minimum acceptable amount of free RAM has been increased on the SoundPoint IP 320,
330, and 430 in order that functions such as ringtones are not affected.
47897 The Back soft key works when a user tries to exit from Instant Message menu.
52119 VVX 1500 phones no longer reboot during G.729 packet loss concealment such as when the
remote phone is placed on hold.
52787 The configuration parameter voIpProt.SIP.requestValidation.x.method=source does
works with DNS SRV Static Cache
Polycom, Inc.
108
Polycom UC Software 4.1.5 Release Notes
53473 When the SoundStation IP 7000 is used with an HDX, the parameter
voice.volume.persist.handsfree=0 also affects the HDX.
54549 Changes in the display color palette on the SoundPoint IP 450 no longer cause contrast
problems.
54751 SIP INVITE messages can be sent when dialing a number containing the period character.
54832 The phone enables user to add more than 32 characters in Hot Dial screen (applies to VVX 1500,
321, 325, 330, 331, and 335).
54867 In the Contact Directory, the text fields scroll to the left to reveal the first character as you move
the text cursor left (applies to SoundPoint IP 321, 325, 330, 331, and 335).
54908 An unexpected colon has been removed in the scrolling status line during an incoming call
(applies to SoundPoint IP 321, 325, 330, 331, and 335).
55099 In a long SRTP conference, steering video on the VVX 1500 between active and inactive no
longer causes the video leg to fail.
55120 Dialing numbers in the Contact Directory no longer opens contacts for editing (applies to
SoundPoint IP 550, 560, 650, and 670).
55296 On the VVX 1500, the dial pad widget displays when attempting to conference or transfer a held
call while in a ringback state.
55378 The VVX 1500 phone can invoke LCD power down mode after a remote end places the call on
hold.
55415 The phone enables the user to enter more characters than it is capable of saving in the Contact
Directory fields.
55420 The VVX 1500 phone can play back video after a SIP re-INVITE message is sent to an RMX
meeting room.
55560 The VVX 1500 phone displays correct call timer values while in an H.323 call to an RMX-2000.
55618 Switching to Katakana characters before the character selection widget times out no longer
produces random characters that on occasion cause the phone to malfunction (applies to
SoundPoint IP 450, 550, 560, 650, 670; SoundStation 5000 and 7000).
55844 Proceeding outgoing call state on one line is adversely affected by an outgoing call on another
line (applies to SoundPoint IP 321, 325, 330, 331, and 335).
55884 The displays on a SoundPoint IP 650 with expansion modules no longer freeze during a
consultative transfer.
56032 SoundPoint IP 650 phones with two expansion modules no longer reboot while monitoring
continuous BLF traffic.
56488 In packets sent from the client, the Parameter Request List option no longer contains two
duplicate requests for the options Router (3) and Domain Name (15) (applies to SoundStation IP
6000 and 7000).
56641 The phone no longer ignores the LLDP broadcast from a switch. It will default to the data VLAN
instead of the voice VLAN. There is a LOSS of LINK during the boot process causing LLDP to fail
(applies to SoundStation IP 6000 and 7000).
Polycom, Inc.
109
Polycom UC Software 4.1.5 Release Notes
56836 After dialing and then adjusting the volume, lifting the handset no longer dials the last hot-dialed
number immediately (applies to SoundPoint IP 550, 560, 650, and 670).
57133 The SoundPoint IP 321, 330, and 331 phones can display a customer supplied logo.
57457 The LoudRing.wav audio file has been distributed in release 3.2.2.
57796 Invalid Message-Summary Event no longer results in invalid MWI notification.
57849 The SoundPoint IP 330 and 550 phones can acquire the correct VLAN via LLDP.
58024 The Hold function on the VVX 1500D no longer fails in a specific customer scenario.
58024 The Hold function on the VVX 1500D no longer fails in a specific customer scenario.
Configuration File Enhancements
Refer to the following table for a list of enhancements made to the SIP 3.2.3 configuration file parameters.
Table 16: Software Version 3.2.3 Parameter Enhancements
File
Change
Configuration Parameter
phone1
added
reg.n.server.1.failOver.reRegisterOn
phone1
added
reg.n.server.1.failOver.failBack.mode
phone1
added
reg.n.server.1.failOver.failBack.timeout
phone1
added
reg.n.server.2.failOver.reRegisterOn
phone1
added
reg.n.server.2.failOver.failRegistrationOn
phone1
added
reg.n.server.2.failOver.failBack.mode
phone1
added
reg.n.server.2.failOver.failBack.timeout
phone1
added
reg.n.outboundProxy.failOver.reRegisterOn
phone1
added
reg.n.outboundProxy.failOver.failRegistrationOn
phone1
added
reg.n.outboundProxy.failOver.failBack.mode
phone1
added
reg.n.outboundProxy.failOver.failBack.timeout
phone1
added
reg.n.useCompleteUriForRetrieve
sip
added
voIpProt.server.1.failOver.reRegisterOn
sip
added
voIpProt.server.1.failOver.failRegistrationOn
sip
added
voIpProt.server.1.failOver.failBack.mode
sip
added
voIpProt.server.1.failOver.failBack.timeout
sip
added
voIpProt.server.2.failOver.reRegisterOn
sip
added
voIpProt.server.2.failOver.failRegistrationOn
Polycom, Inc.
New Value
1
110
Polycom UC Software 4.1.5 Release Notes
File
Change
Configuration Parameter
sip
added
voIpProt.server.2.failOver.failBack.mode
sip
added
voIpProt.server.2.failOver.failBack.timeout
sip
added
voIpPort.SIP.useCompleteUriForRetrieve
sip
added
voIpProt.SIP.outboundProxy.failOver.reRegisterOn
sip
added
voIpProt.SIP.outboundProxy.failOver.failRegistrationOn
sip
added
voIpProt.SIP.outboundProxy.failOver.failBack.mode
sip
added
voIpProt.SIP.outboundProxy.failOver.failBack.timeout
sip
added
voIpProt.H323.blockFacilityOnStartH245
0
sip
added
se.destination
chassis
sip
added
voice.codecPref.IP _5000.G711Mu
2
sip
added
voice.codecPref.IP _5000.G711A
3
sip
added
voice.codecPref.IP _5000.G729AB
4
sip
added
voice.codecPref.IP _5000.G722
1
sip
added
voice.codecPref.IP _5000.iLBC.13_33Kbps
sip
added
voice.codecPref.IP _5000.iLBC.15_2Kbps
sip
added
voice.gain.rx.analog.chassis.IP _5000
0
sip
added
voice.gain.rx.analog.ringer.IP _5000
0
sip
added
voice.gain.rx.digital.chassis.IP _5000
11
sip
added
voice.gain.rx.digital.ringer.IP _5000
-12
sip
added
voice.gain.tx.analog.chassis.IP _5000
0
sip
added
voice.gain.tx.digital.chassis.IP _5000
15
sip
added
voice.aes.hf.duplexBalance.IP _5000.0
10
sip
added
voice.aes.hf.duplexBalance.IP _5000.1
9
sip
added
voice.aes.hf.duplexBalance.IP _5000.2
8
sip
added
voice.aes.hf.duplexBalance.IP _5000.3
7
sip
added
voice.aes.hf.duplexBalance.IP _5000.4
6
sip
added
voice.aes.hf.duplexBalance.IP _5000.5
5
sip
added
voice.aes.hf.duplexBalance.IP _5000.6
4
Polycom, Inc.
New Value
1
111
Polycom UC Software 4.1.5 Release Notes
File
Change
Configuration Parameter
New Value
sip
added
voice.aes.hf.duplexBalance.IP _5000.7
3
sip
added
voice.aes.hf.duplexBalance.IP _5000.8
2
sip
added
voice.ns.hf.IP _5000.enable
1
sip
added
voice.ns.hf.IP _5000.signalAttn
-6
sip
added
voice.ns.hf.IP _5000.silenceAttn
-9
sip
added
voice.rxEq.hf.IP _5000.preFilter.enable
1
sip
added
voice.rxEq.hf.IP _5000.postFilter.enable
0
sip
added
voice.txEq.hf.IP _5000.preFilter.enable
0
sip
added
voice.txEq.hf.IP _5000.postFilter.enable
1
Understanding Updates to SIP 3.2.2
This section lists additions and changes, removals, enhancements, and configuration file parameter
changes to SIP 3.2.2 beside their respective Polycom tracking ID number.
New or Enhanced Features
41450 Change of the real time operating system (applies to VVX 1500).
43760 H.323 signaling protocol support for video (applies to VVX 1500).
43862 Support for Webkit browser to replace the XHTML browser (applies to VVX 1500).
45172 Support for iLBC audio codec (applies to VVX 1500).
47173 Support for H.261 video codec (applies to VVX 1500).
48557 Max video bit rate defaults to 384 Kbps (applies to VVX 1500).
48743 Upgraded curl library to version 7.19 (applies to VVX 1500).
48961 Support for H.235 security (applies to VVX 1500).
49069 Added support for iLBC audio codec (applies to SoundStation IP 6000 and 7000).
49079 Support for mutual TLS authentication (applies to VVX 1500).
49277 Support for LLDP protocol (applies to VVX 1500).
49430 Added ITU-T G.719 vocoder (applies to VVX 1500)
50125 Outgoing calls support dual (SIP /H.323) protocols (applies to VVX 1500).
51084 Support for video fast update request via RTCP, RFC 5104 (applies to VVX 1500).
52944 Menu support applicable to H.323 usage (applies to VVX 1500).
Polycom, Inc.
112
Polycom UC Software 4.1.5 Release Notes
53849 Formalized support for DTMF via SIP INFO (initially supported in SIP 3.2.0).
54025 Increased maximum size of contact directory to 128 to facilitate complex dialing scenarios.
54239 Added user accessible menu option to select the video call rate. Default configured using the
configuration parameter video.callRate (applies to VVX 1500).
Discontinued Features
52522 Removed Launchpad Feature (applies to VVX 1500).
Enhanced Capabilities
44782 Improved phone UI response when a local conference is active (applies to VVX 1500).
44980 The phone falls back to configured video codec configuration for Tx video when incoming
signaling lacks codec modifiers (applies to VVX 1500).
47023 Text font no longer randomly changes (applies to VVX 1500).
47476 Using the XML API, when the user is inside an XHTML Form Field, the Submit soft key displays
properly.
47768 CDP power usage advertisement matches the peak power conditions (applies to SoundPoint IP
450).
48175 EFK feature can establish conference calls (applies to VVX 1500).
48784 Soft keys are restored after rejecting a call from within the Applications UI context (applies to VVX
1500).
48857 Recording (R) no longer stops or reboots phone in various high load scenarios such as (a)
recording during SRTP conference call, or (b) recording while browsing the application menu
during non-SRTP conference call (applies to VVX 1500).
48921 Digit key presses are no longer missed in certain scenarios (applies to VVX 1500).
50152 Change non-null sticky primary filter, search (filtered) bar remains on old data (applies to VVX
1500).
50192 Media Statistics menu displays correctly for several languages (applies to VVX 1500).
50286 Pressing page down key # does not move entry list after pressing page up key * in quick search
menu (applies to VVX 1500).
50531 The SoundStation IP 7000 phone can startup without network connection when using the PIC
cable.
50624 The phone sends a 603 Decline message when an inbound call times out.
51141 A small number on the left side of the scrolling status bar has been removed.
51449 Out of Dialog Refer based dialing on the VVX 1500 no longer fails. SDP on INVITE from VVX is
missing media attributes, generating a 606 response.
51533 Backlight intensity change updates appropriately in Overrides configuration file.
51605 VVX 1500 phones correctly handle back-to-back Push requests.
Polycom, Inc.
113
Polycom UC Software 4.1.5 Release Notes
51643 Japanese displays properly on the SoundStation IP 6000 and VVX 1500.
51753 Display text on the SoundPoint IP 450 looks clearer.
51959 Handling of Hold re-Invites is correct after one-touch blind transfer to full park orbit.
51965 HTTP request messages are directed to proxy.
52164 Hot-dial on the VVX 1500 works in headset mode.
52360 Auth Password field can no longer be viewed in Web configuration page.
52365 The phones can easily transition from LLDP to CDP.
52370 Removing Ethernet cable from the SoundStation IP 7000 no longer un-mutes the muted phone.
52376 The parameter daylightSavingsTime can now be disabled. Introduced in SIP 3.2.0 (applies
to SoundStation IP 6000 and 7000).
52381 The Retrieve, Directed, and Group soft keys no longer disappear after entering some digits. This
occurs when using the Call Park/Pick-Up feature using SIP signaling. Introduced in SIP 3.2.0
(applies to SoundPoint IP 430, 450, and SoundStation 6000).
52415 When using enhanced BLF, ringtones are no longer suppressed when a user is parked.
52568 The SoundStation IP 7000 phone plays DTMF tone with the default configuration.
52580 Delayed DTMF audio feedback is heard when conferencing third POTS end while using the
SoundStation IP 7000 User Interface.
52656 The VVX 1500 phone supports transcoding of video codecs that are not included in the far-ends
capability set
52678 Using the quick/AdvFind search on full last name in the Corporate Directory no longer misses
some entries.
52709 License menu displays Active to indicate a license with no expiry date.
52770 Message-summary SUBSCRIBE is sent when reg.x.type=shared.
52836 The phone no longer enables the user to enter more than the maximum allowed (32) characters
in hot dial and contact directory operations.
52860 Split soft key no longer displays while transferring calls if the call per line limit is reached.
52883 When a call is placed to a shared line, the ringer for an IP 650 no longer stutters when the call is
picked up at another station.
52943 LLDP reported power usage in logs indicates appropriate power consumption.
52950 Packet Loss and Burst Gap Loss metrics too high when calling IVR, caused by valid gap in audio
sent from IVR.
52963 The SoundPoint IP 320, 321, 330, and 331 phones no longer reboot when the user presses NN#
from idle screen to invoke Contact Directory entry screen for NN speed dial index.
52971 The phone no longer reboots when the efkprompt label is longer than 32 characters.
52977 The Directory soft key on the VVX 1500 does not disappear after selecting Blind transfer mode.
53007 VQMon on the VVX 1500 phone computes RFactor and MOS quality scores for the G7221C
codec.
Polycom, Inc.
114
Polycom UC Software 4.1.5 Release Notes
53034 SUBSCRIBE for BLA with expires: 0 received from server is recognized as terminating the
subscription
53254 VVX 1500 enables users to change Auth Password for SIP Lines through the phone’s user
interface.
53598 Side-tone disappears after a call hangs up on headset using GN9350e with EHS.
53656 Part number in Phone Status menu displays proper part number.
53855 When a phones extension has an underscore in the name, followed only by numbers, the
underscore is no longer removed in SIP signaling and the device can be found.
53917 The phone no longer reboots in a certain scenario when using the Join key.
53944 SoundPoint IP 320, 330, 321, and 331; SoundStation IP 7000: Phone displays Dir soft key in
Korean and Slovenian languages.
53946 SoundPoint IP 550, 560, 650, and 670 phones no longer randomly display the time and date
behind a custom idle display.
53975 The phones will send a SUBSCRIBE message in a certain scenario when using SCA with barge
in enabled.
54034 The VVX 1500 phone no longer generates loud static when CNG packets are received.
54139 Consultative transfer uses the correct URI on REFER.
54262 The Ethernet status menu on the SoundPoint IP 320 and 321 displays the correct information.
54631 The Voice/Video call type prompt on the SoundStation IP 7000 defaults to Voice.
54765 The VVX 1500 phone fails to resend INVITE after 401 from server when second INVITE is
roughly 1500 bytes.
54768 VVX 1500 phones can establish calls properly when booted without a network connection.
54886 The phones send re-Invite with SDP containing session attribute a=sendrecv upon resuming a
call when the call is initiated with a=sendrecv offered.
54940 New REQUESTS sent directly to far end; route set ignored after a call is placed on MOH,
resulting in a loss of audio.
55052 Additional parameter in the From header of INVITE no longer causes 1-way audio when it is not
found in the ACK to a 200 OK.
Configuration File Enhancements
Refer to the following table for a list of enhancements made to the SIP 3.2.2 configuration file parameters.
Table 17: Software Version 3.2.2 Parameter Enhancements
File
Change
Configuration Parameter
phone1
added
call.autoOffHook.1.protocol
phone1
added
call.autoOffHook.2.protocol
phone1
added
call.autoOffHook.3.protocol
Polycom, Inc.
Old Value
New Value
115
Polycom UC Software 4.1.5 Release Notes
File
Change
Configuration Parameter
phone1
added
call.autoOffHook.4.protocol
phone1
added
call.autoOffHook.5.protocol
phone1
added
call.autoOffHook.6.protocol
phone1
added
reg.1.protocol.H323
phone1
added
reg.1.protocol.SIP
phone1
added
reg.1.server.H323.1.address
phone1
added
reg.1.server.H323.1.expires
phone1
added
reg.1.server.H323.1.port
phone1
added
reg.2.protocol.H323
phone1
added
reg.2.protocol.SIP
phone1
added
reg.2.server.H323.1.address
phone1
added
reg.2.server.H323.1.expires
phone1
added
reg.2.server.H323.1.port
phone1
added
reg.3.protocol.H323
phone1
added
reg.3.protocol.SIP
phone1
added
reg.3.server.H323.1.address
phone1
added
reg.3.server.H323.1.expires
phone1
added
reg.3.server.H323.1.port
phone1
added
reg.4.protocol.H323
phone1
added
reg.4.protocol.SIP
phone1
added
reg.4.server.H323.1.address
phone1
added
reg.4.server.H323.1.expires
phone1
added
reg.4.server.H323.1.port
phone1
added
reg.5.protocol.H323
phone1
added
reg.5.protocol.SIP
phone1
added
reg.5.server.H323.1.address
phone1
added
reg.5.server.H323.1.expires
phone1
added
reg.5.server.H323.1.port
Polycom, Inc.
Old Value
New Value
116
Polycom UC Software 4.1.5 Release Notes
File
Change
Configuration Parameter
phone1
added
reg.6.protocol.H323
phone1
added
reg.6.protocol.SIP
phone1
added
reg.6.server.H323.1.address
phone1
added
reg.6.server.H323.1.expires
phone1
added
reg.6.server.H323.1.port
sip
added
call.autoAnswer.H323
0
sip
added
call.autoAnswer.micMute
1
sip
added
call.autoAnswer.ringClass
4
sip
added
call.autoAnswer.SIP
0
sip
added
call.autoAnswer.videoMute
0
sip
added
call.autoRouting.preference
line
sip
added
call.autoRouting.preferredProtocol
SIP
sip
removed
httpd.lp.port
sip
removed
httpd.ta.enabled
sip
added
log.level.change.h323
4
sip
added
log.level.change.poll
4
sip
added
log.level.change.push
4
sip
added
log.level.change.wmgr
4
sip
removed
mb.launchpad.enabled
sip
removed
mb.main.1.icon
sip
removed
mb.main.1.text
sip
removed
mb.main.1.url
sip
removed
mb.main.2.icon
sip
removed
mb.main.2.text
sip
removed
mb.main.2.url
sip
removed
mb.main.3.icon
sip
removed
mb.main.3.text
sip
removed
mb.main.3.url
Polycom, Inc.
Old Value
New Value
117
Polycom UC Software 4.1.5 Release Notes
File
Change
Configuration Parameter
sip
removed
mb.main.4.icon
sip
removed
mb.main.4.text
sip
removed
mb.main.4.url
sip
removed
mb.main.5.icon
sip
removed
mb.main.5.text
sip
removed
mb.main.5.url
sip
removed
mb.main.6.icon
sip
removed
mb.main.6.text
sip
removed
mb.main.6.url
sip
added
sec.H235.mediaEncryption.enabled
1
sip
added
sec.H235.mediaEncryption.offer
0
sip
added
sec.H235.mediaEncryption.require
0
sip
added
up.callTypePromptPref
1
sip
added
up.enableCallTypePrompt
1
sip
changed
up.idleBrowser.enabled
sip
added
up.manualProtocolRouting
1
sip
added
up.manualProtocolRouting.softKeys
1
sip
changed
video.autoStartVideoTx
1
sip
added
video.callRate
448
sip
added
video.codecPref.H261
4
sip
changed
video.enable
1
sip
added
video.forceRtcpVideoCodecControl
0
sip
changed
video.maxCallRate
512
sip
added
video.profile.H261.annexD
sip
added
video.profile.H261.CifMpi
1
sip
added
video.profile.H261.jitterBufferMax
2000
sip
added
video.profile.H261.jitterBufferMin
150
sip
added
video.profile.H261.jitterBufferShrink
70
Polycom, Inc.
Old Value
New Value
0
118
Polycom UC Software 4.1.5 Release Notes
File
Change
Configuration Parameter
Old Value
New Value
sip
added
video.profile.H261.QcifMpi
1
sip
changed
video.screenMode
normal
sip
changed
video.screenModeFS
normal
sip
added
voice.audioProfile.G719.32Kbps.
107
payloadType
sip
added
voice.audioProfile.G719.48Kbps.
108
payloadType
sip
added
voice.audioProfile.G719.64Kbps.
109
payloadType
sip
added
voice.audioProfile.G719.jitterBufferMax
200
sip
added
voice.audioProfile.G719.jitterBufferMin
40
sip
added
voice.audioProfile.G719.jitterBuffer
1500
Shrink
sip
added
voice.audioProfile.G719.payloadSize
sip
added
voice.codecPref.VVX_1500.G719.32Kbps
sip
added
voice.codecPref.VVX_1500.G719.48Kbps
sip
added
voice.codecPref.VVX_1500.G719.64Kbps
sip
changed
voice.gain.tx.digital.chassis.VVX_1500
sip
added
voIpProt.H323.autoGateKeeperDiscovery
0
sip
added
voIpProt.H323.dtmfViaSignaling.enabled
1
sip
added
voIpProt.H323.dtmfViaSignaling.
1
20
6
3
H245alphanumericMode
sip
added
voIpProt.H323.dtmfViaSignaling.
1
H245signalMode
sip
added
voIpProt.H323.enable
0
sip
added
voIpProt.H323.local.port
1720
sip
removed
voIpProt.local.port
sip
added
voIpProt.server.H323.1.address
sip
added
voIpProt.server.H323.1.expires
sip
added
voIpProt.server.H323.1.port
Polycom, Inc.
119
Polycom UC Software 4.1.5 Release Notes
File
Change
Configuration Parameter
Old Value
New Value
sip
added
voIpProt.SIP.dtmfViaSignaling.rfc2976
sip
added
voIpProt.SIP.enable
1
sip
added
voIpProt.SIP.local.port
5060
Understanding Updates to SIP 3.2.1B
This section lists additions and changes, removals, enhancements, and configuration file parameter
changes to SIP 3.2.1B beside their respective Polycom tracking ID number.
New or Enhanced Features
48947 Support for the SoundPoint IP 335 product.
Configuration File Enhancements
Refer to the following table for a list of enhancements made to the SIP configuration file parameters.
Table 18: Software Version 3.2.1B Parameter Enhancements
File
Change
Configuration Parameter
New Value
Description
sip
added
ind.anim.IP_335.42.frame.1.bitmap
Handset
sip
added
ind.anim.IP_335.42.frame.1.duration
1300
See Administrators
Guide for SIP 3.2.2
for details
sip
added
ind.anim.IP_335.42.frame.2.bitmap
PlumHd
sip
added
ind.anim.IP_335.42.frame.2.duration
1300
sip
added
ind.anim.IP_335.43.frame.1.bitmap
Headset
sip
added
ind.anim.IP_335.43.frame.1.duration
1300
sip
added
ind.anim.IP_335.43.frame.2.bitmap
PlumHd
sip
added
ind.anim.IP_335.43.frame.2.duration
1300
sip
added
ind.anim.IP_335.44.frame.1.bitmap
Speaker
sip
added
ind.anim.IP_335.44.frame.1.duration
1300
sip
added
ind.anim.IP_335.44.frame.2.bitmap
PlumHd
sip
added
ind.anim.IP_335.44.frame.2.duration
1300
Polycom, Inc.
See Administrators
Guide for SIP 3.2.2
for details
120
Polycom UC Software 4.1.5 Release Notes
Understanding Updates to SIP 3.2.1
This section lists additions and changes, removals, enhancements, and configuration file parameter
changes to SIP 3.2.1 beside their respective Polycom tracking ID number.
Enhanced Capabilities
53322 Setting voIpProt.local.port to a non-standard port does not send from or advertise that
port.
53611 User Language Selection is retained during an upgrade to SIP 3.2.0.
53685 The phones no longer ignore nat.ip parameters.
53852 DTMF duration on the SoundStation IP 7000 defaults to 300ms for HDX integration.
Understanding Updates to SIP 3.2.0
This section lists additions and changes, removals, enhancements, and configuration file parameter
changes to SIP 3.2.0 beside their respective Polycom tracking ID number.
New or Enhanced Features
22527 Implemented Scrolling Status Bar on the SoundPoint IP 320, 321, 330, 331, 550, 560, 650, 670,
and SoundStation IP 6000 and 7000.
26754 Support for the iLBC codec on the SoundPoint IP 320, 321, 330, 331, 450, 550, 560, 650, and
670.
30079 Added support for mutual TLS authentication. See Technical Bulletin 52609 for more details on
this feature.
32259 Microbrowser recognizes multiple mime types.
32753 Support for LLDP protocol. To take full advantage of this feature, you will need to use BootROM
4.2.0.
34782 Replaced libSRTP algorithms with OpenSSL versions.
35525 The DND icon contains text identifying that DND is active.
37118 Added the ability to take a screen capture.
39358 Added a Loud Ringer Ringtone selection. See Technical Bulletin 39358 for instructions on how
this can be configured.
30855 Create a SoundStation IP 7000 Setup Guide.
41579 Met requirements of ETSI TS 102 027-2 v4.1.1 RFC 3261 compliance test for Anatel/Brazil.
43141 Support for Statically Configured BLF and Call Park and Retrieve enhancements.
43142 Support for single button Blind Transfer and Retrieve of a call designated as an automata in the
dialog used for Statically Configured BLF.
43646 Improved boot speed in some situations where the boot server is incorrectly configured.
Polycom, Inc.
121
Polycom UC Software 4.1.5 Release Notes
45057 Languages selection presented in appropriate language.
45174 Upgraded zlib to version 1.2.3.
45743 Upgraded curl library to version 7.19.2.
45787 Added instructions to the SoundPoint IP 450, 550, 560, 650, and 670 for changing label colors in
the User Guides.
45791 Added a configuration option on the SoundStation IP 7000 to disable digit-map rules for Remote
Dialing when connected to an HDX.
46093 Added the ability for User to enable/disable display of idle browser from menu.
46113 Added navigation button shortcuts in Idle Mode consistent with other phone models (applies to
SoundPoint IP 320, 321, 330, and 331).
46248 Added an Admin menu option on the SoundStation IP 7000 to manually specify the value to be
used as the extension displayed on the phone screen.
46424 Improved readability of Menu items when using Background images on the display.
46446
New menu option to view the status of feature licenses.
46683 Removed Background from scrolling Status Bar for improved readability.
47355 Scrolling Status Bar gives equal time to each status message.
47390 Added configuration parameters for select ETSI SIP compliance requirements.
47463 The phones allow for secure entry of passwords in the micro-browser API.
47487 Added the ability to enable/disable a Back soft key in the microbrowser
47689 Added support for SoundStation IP 7000/HDX6000 Integration. This feature requires a future
update release to the HDX6000 software.
47749 Support Transmission of Join Header as per RFC 3911.
48004 Support for BLF call pick-up using Dialog-info within an INVITE with Replaces header.
48055 Improved user experience of the Enhanced BLF feature when an incoming call occurs whilst the
user is viewing BLF monitored line call details.
48109 Included fmtp attribute specifying Mode=30 in the SDP when 13.33 Kbps iLBC is used.
48136 Removed platform specific TFTP code and instead used TFTP support in curl library 7.19.2.
48137 Support for BLF call pick-up using Dialog-info within an INVITE with Replaces header.
48205 Support for the iLBC Codec (applies to SoundStation IP 6000 and 7000).
48559 Consistent scrolling status line on various phones (applies to SoundPoint IP 450, 550, 560, 650,
and 670; SoundStation IP 6000 and 7000).
48578 Reduced the local Contact Directory maximum to 99 on the SoundPoint IP 430.
48579 Reduced the maximum number of calls supported to 4 (from 8) on the SoundPoint IP 430.
48664 Added user accessible menu option to display whether a device certificate is installed.
48678 Media Statistics menu is more easily accessible. Accessed from Menu > Status > Diagnostics >
Media Statistics.
Polycom, Inc.
122
Polycom UC Software 4.1.5 Release Notes
48738 Added configurable behavior for Directed Call Pick-Up as used for Enhanced BLF.
48780 Added option to apply digit-map rules to tel:URI initiated calls.
48846 Added configuration option for whether the call appearance on a remotely monitored BLF line
should be presented on the monitoring/attendant phone.
48861 Add configuration option voIpProt.SIP.strictReplacesHeader to control whether the
phone requires call-id, to-tag, and from-tag to perform and INVITE with Replaces.
48984 The phone will populate the display-name field in the To header of responses that it generates.
48998 Added configuration option for the phone to send 486 Busy when a call is rejected.
49309 Combined the SoundPoint IP 550 and 560 user guides.
49465 Updated Destination of outbound call based on the display name in the SIP To header
responses.
49660 During call forwarding user=phone should be included in refer-to parameter of Refer header.
49695 Allow for SDP offer or answer in provisional reliable response and PRACK request and response.
49839 RTP Rx detects and corrects for G.722, G.722.1, G.722.1C, and G.719 RTP timestamp
increments based on different sample rates.
50769 Added support for Hook-Flash during POTS calls on the SoundStation IP 7000.
50927 Added Equifax Secure eBusiness CA-1 to the trusted CA list.
51419 RFC2543 Hold not working when video SDP present in certain scenarios.
Discontinued Features
48283 Removed support for SoundPoint IP 301, 501, 600, and 601 phones.
48698 Removed support for SoundStation IP 4000.
Enhanced Capabilities
Application load progress bar matches actual progress.
29148 The phone formats the file system when it notes an error on the screen while loading large
configuration files.
29344 HTTP Digest Authentication works on IIS.
30219 Logs are uploaded when phone resets to factory default.
31858 When two phones with a shared line simultaneously resume a held call, the phone which did not
retrieve the call shows call in progress on its shared line indicator.
34681 The parameters stickyAutoLineSeize and call.enableOnNotRegistered=0 do not
seize correctly if the 1st line is unregistered.
35288 The Web Configuration Utility uses less memory during initialization.
35991 The Roaming Buddy list with Office Communicator reports the proper status of all buddies.
36969 The SoundStation IP 6000 displays Japanese language correctly.
Polycom, Inc.
123
Polycom UC Software 4.1.5 Release Notes
38348 The SRTP call displays proper line icons in a certain scenario on the SoundPoint IP 320, 321,
330, and 331.
38392 Performing a Blind Transfer from an encrypted phone to an unencrypted private line establishes
the new call as encrypted.
38418 The phones no longer show SRTCP authentication failure at log level 0.
38824 After audio diagnostics such as Record and Play in handset, the 1st call is no longer established
in handset mode even if the handset is ON-HOOK.
39013 Attaching a cell phone cable to the SoundStation IP 7000 no longer invokes the Cell phone UI
until a physical cell phone is attached.
39143 The P-Asserted-Identity header in initial INVITE message is no longer used for caller ID.
39949 The navigation icon in the Corporate Directory correctly displays the available navigation options
when using the keypad to navigate (applies to SoundPoint IP 320, 321, 330, and 331).
40679 Changing the status on the MyStatus menu of the SoundStation IP 6000 changes the OC client
status when roaming_buddies.reg= 1.
40892 The Time/Date displays on the SoundStation IP 7000 when the first phone call is established.
41939 The user is not able to play the WAV file when it has a call on hold and also in remote busy state.
Junk characters appear in audio player.
42092 Special Slovenian characters are included in the phone’s fonts.
42213 The SIP: string displays on the SoundStation IP 7000 when using URL dialing.
42611 Recording no longer begins when a full USB drive is attached
42761 Pressing the Content soft key on the SoundStation IP 7000 no longer prompts the user to choose
VGA input.
43910 The microbrowser can process an http response which contains an image/bmp.
43916 Configured sampled wave files can be downloaded onto the phone depending on sufficient RAM
Disk size.
43990 Missing glyphs in the Katakana bit stream fonts on the SoundStation IP 7000.
44100 Call display names containing an @ symbol no longer truncate characters after the @ symbol.
44248 The microbrowser displays an error message when unsupported media is configured in the
microbrowser URL.
44273 The phones can process all contacts in a SIP Contact header containing a comma separated list.
44278 The phone numbers are displayed correctly on line keys when the length of a phone number is
more than 10 characters.
44301 The Date on the SoundStation IP 6000 and 7000 when the idle browser is enabled.
44377 The Redial key can be reassigned.
44443 The Menu exit via the Menu key is ignored while in Edit mode (applies to SoundPoint IP 320, 321,
330, and 331).
44635 The SoundStation IP 6000 phone uses the correct configuration parameters to download
customizable fonts.
Polycom, Inc.
124
Polycom UC Software 4.1.5 Release Notes
44783 The Cipher list is the same for different TLS transactions.
44844 USB Call Recording can be stopped using the Stop soft key.
44855 When using Call Lists, the
Missed Calls are incremented on Call Forward on Busy.
44892 When using SCA Barge-In on the SoundStation IP 6000 and 7000 phones, the user no longer
barges in to the wrong call in certain scenarios.
44962 The phone no longer displays 3-way animation icon in held screen when conference legs on hold.
45143 When the maximum conference size is reached when using Centralized Conference, the phone
no longer displays a local conference UI.
45327 When the user establishes a call between two phones configured as shared lines, and presses
the down arrow key, all soft keys no longer disappear.
45428 An unexpected re-INVITE no longer occurs before BYE when removing a leg from a conference
call.
45650 In a double hold with music on hold and a non-Polycom SIP phone, – MOH no longer fails.
45658 The platform string in transmitted CDP packets is consistent across SoundPoint IP products.
45716 Text on the SoundPoint IP 450 is consistent as on other phones.
45835 Status Bar text on the SoundPoint IP 450 is easier to read on some backgrounds.
45943 Correct logic is used when picking line for outgoing call in a multiple registration scenario.
46068 Transfer On Proceeding is supported when using a proxy server.
46334 DTMF local rendering does not stop. If the far end holds while local digit key is pressed then the
far end resumes.
46478 On the EFK feature, the phone sends invite when executing $Cwaitdialtone$.
46513 Dialog Event Package Content Guideline 6B (Local Identity).
46514 Dialog Event Package Content Guideline 6C (Local Target).
46547 Warning Header Text notification on the SoundStation IP 7000 displays on phone (when
configured).
46550 Directed-Call-Pickup no longer fails when SIP server is a proxy.
46588 Info soft key on the SoundStation IP 7000 is no longer missing in the Contact Directory.
46738 The attendant.ringType parameter is removed from the override file when default (silent)
attendant ring type is selected.
46741 Using enhanced BLF, when the watched line hangs up an outgoing call, the remote call
appearance screen times out on the console phone.
46770 On the microbrowser, the * and # buttons work correctly when the text input mode is set to
numeric on input fields.
46899 When using the electronic hookswitch, audio is heard during an active call if the user answers by
pressing the hookswitch button immediately on a Jabra headset under a specific scenario.
47039 The line LED flashes instead of remaining a stable green when an active call is kept on hold
during an incoming call.
Polycom, Inc.
125
Polycom UC Software 4.1.5 Release Notes
47123 When using the USB Call Recording, the missed call notification no longer displays on the audio
player screen if an incoming call is not answered during playback.
47207 When the MUTE is active on the SoundStation IP 7000, it no longer covers up the dialing fields.
47248 Hot dial works when lifting the handset for the second call when
call.stickyAutoLineSeize=1.
47300 URL dial disabled message displays and successfully routes to voicemail from Message Center
tab.
47336 The Received\Missed call list on the SoundStation IP 7000 no longer shows the IP address of the
SIP server instead of the Extension number of a call received/Missed from a SIP extension.
47464 When two incoming calls are active on a phone, lifting the handset or pressing the handsfree key
to answer the call no longer results in the most recent call being answered even though the ring
tone is played according to the first incoming call (applies to SoundPoint IP 320 and 330, and
SoundStation IP 7000).
47535 The soft keys no longer reset to the default layout on an inbound call in some multiple call
handling scenarios.
47566 When an internal URI is executed with multiple VolUp and VolDown action URIs, the Ringer
horizontal bar is seen and the Volume sound going UP and DOWN is heard.
47578 When using the Corporate Directory on the SoundPoint IP 320, 321, 330, 331, the sticky
attributes are saved.
47612 When using BLF, cancelling a Transfer for a call that was initiated using Directed Call Pick-Up
sequence results in the correct caller-id display to the user.
47641 The Network Link Down message on the SoundStation IP 7000 displays on the screen unless the
phone reboots and comes up with Ethernet cable.
47695 When the phones have two registrations, the NewCall soft key no longer displays for alerting call
appearance when there are max call appearances (applies to SoundPoint IP 320, 321, 330, 331,
430, and 450).
47699 When using XML API Internal URIs on the SoundStation IP 6000, the Tel URI is works properly if
embedded within a couple of internal URI actions.
47712 A local contact directory search on the SoundPoint IP 320, 321, 330, and 331 works correctly.
47724 Mute icon and Call appearance counter on the SoundPoint IP 450 no longer conflict when DND is
turned on and multiple call appearances are present on the phone.
47729 The on-hook dialing widget no longer uses multi-tap behavior but is not in multi-tap mode.
47746 The NewCall soft key is not displayed when phone holds max conference calls.
47798 The location of the Transfer and Conference soft keys on the SoundStation IP 7000 are more
easily accessible during conference setup.
47847 When using BLF, the monitoring phone continues ringing if a shared line is seized while the
monitored line has an incoming call.
47853 When the headset memory mode is active, the Headset key continues blinking during incoming
calls after ending the first active call.
47862 The Time and Date on the SoundStation IP 6000 displays during a call.
Polycom, Inc.
126
Polycom UC Software 4.1.5 Release Notes
47863 The phone’s HTTP server is no longer sending some HTTP traffic in very small TCP segments.
47916 The Resume soft key on the SoundPoint IP 320, 321, 330, and 331 is available for second call
appearance after splitting conf established through Join from different shared line registrations.
47921 The order of call appearances on the SoundPoint IP 320, 321, 330, and 331
other phones after splitting a conference.
is consistent with
47929 Rendering special characters like no longer break the hyperlink style display.
47932 The Call widget counter (1/n) appears while in the dial tone state.
47951 Transfer has precedence over pickup of a ringing BLF line when pressing the line key during a
call transfer.
47953 Call info display on the SoundStation IP 6000 displays properly when volume up/down key is
pressed.
47958 More than one contact can be added when the SoundStation IP 7000 is configured with no
Ethernet cable connected + HDX.
47962 An incorrect icon is no longer displayed when Redialing POTS call on the SoundStation IP 7000.
48003 The SoundStation IP 7000 phone no longer dials a POTS call as a video call when dialing from
the idle state for a certain configuration.
48011 Use of the Idle Browser on the SoundStation IP 7000 no longer interferes with some display
elements such as the Mute Icon, Video/Phone Call pop-up when connected to HDX.
48019 The pop-up message Video or Phone Call? is no longer overwritten by the idle browser on the
SoundStation IP 7000.
48045 When using enhanced BLF, the phone holds the first call when pressing the Dial soft key to make
the second call to the same called party.
48049 When using BLF, the attendant phone displays all remote calls on a BLF monitored line if the
Monitored Phone has a call in the Ringing state.
48061 When using enhanced BLF, the attendant phone updates the 1/x widget when the BLF monitored
line has one or multiple incoming calls being ended.
48069 When using the SCA Barge-In feature, extra soft keys are no longer displayed on remote shared
phone while viewing call appearance list by long pressing line key.
48071 Key:Handsfree internal URI action is executed by the phone in a certain scenario.
48115 HDX no longer plays a ring sound after answering POTS call on the SoundStation IP 7000.
48131 Call Forwarding Status now shows multiple Call Forward Types are selected.
48149 SDP attribute is no longer truncated when first character of the value is a digit.
48162 The Boot Server status field no longer shows an incomplete or blank path if a / is included in the
setting.
48174 A failed call no longer causes subsequent calls to skip URL/Number mode selection.
48179 A called Party number is no longer shown overlapped in incoming event notification when IP
dialed calls are made between unregistered phones.
48209 Left-most character can be deleted before character selection timeout.
Polycom, Inc.
127
Polycom UC Software 4.1.5 Release Notes
48213 Key:LineX is executed only if X is a supported line key for that platform.
48333 When using the USB Call Recording, the USB busy indicator appears on main screen when
recording in progress.
48414 The phone no longer occasionally fails to act on the electronic hookswitch up/down signal from
Plantronics and Hydra headsets.
48700 When using the USB Call Recording, playback can be stopped through a Stop soft key.
48745 LDAP Critical Extension Error 0x0c no longer causes the CD Server to not respond to messages
from phone.
48981 SRTP no longer fails in 3.1.2 when the user presses Hold then Resume during a call. This
happens on several different models of IP phone.
48996 The phone tags correct DSCP value to some packets (Trying, Ringing and OK).
49106 The entire dialed URL is saved in the phone’s call history
49251 The Polish XML Dictionary includes Polish characters.
49300 Ensure that the DTMF tones are being sent via the dtmf start/stop Clink2 API (applies to
SoundStation IP 7000).
49417 The phone no longer reports MOH dialog if SUBSCRIBE received while on hold.
49459 Cancel works after entering hot dial digits.
49461 DND symbol(X) appears after the DND feature is disabled in a certain configuration.
49473 When using the Corporate Directory on the SoundPoint IP 320, 321, 330, 331, using the # key to
change text entry mode it resets the Quick Search timeout timer.
49476 The scrolling indicators on the Corporate Directory work better.
49512 HTTP Refresh header response loads the specified URL on the phones after the specified
amount of time has passed, in a certain situation.
49516 Hanging up the handset terminates calls in Audio or Display Diagnostics.
49523 Asian fonts are clearer on the SoundPoint IP 450 and SoundStation IP 7000.
49548 The Edit and Delete soft keys on the SoundPoint IP 320, 321, 330 and 331 disappear after
deleting the last contact.
49572 When using the Corporate Directory on the SoundStation IP 7000, numeric characters can be
entered in the Quick Search entry field.
49617 The phone plays a dial tone after a hold reminder is played in certain scenarios.
49619 The call waiting beep plays on phone when call hold reminder is set.
49620 Volume settings for Recording work in handsfree mode.
49639 The Handsfree dial tone is no longer interrupted by hold reminder and call waiting ringtones.
49641 Call info display on the SoundStation IP 6000 and 7000 displays properly while changing volume.
49677 The phone complies with RFC4475 3.1.2.3 Negative Content-Length.
49685 On SoundPoint IP 320, 321, 330, and 331, you can enter URLs with uppercase letters.
Polycom, Inc.
128
Polycom UC Software 4.1.5 Release Notes
49692 The seconds colon in the time display blinks for every second on the SoundPoint IP 450.
49693 The ACD icon displays when the parameter voIpProt.SIP.serverFeatureControl.cf=1
is enabled.
49696 After a long LAN outage while downloading a new application, when the phone re-connects to the
network, it displays an error message.
49701 The SoundStation IP 7000 phone response with reg.1.server.1.expires=5 setting is
consistent.
49706 The SIP Extension display on the SoundStation IP 7000 is no longer disabled after disconnecting
from HDX with HDX-Preference option.
49757 The SoundStation IP 7000 phone displays Network Link is Down after the cable is disconnected
from a hub
49758 The SoundStation IP 7000 phone no longer gets into a bad state and can recover from
temporarily unplugging network connection during an active call.
49776 If dir.corp.user is misconfigured, the phone displays Login Error.
49813 When using the Corporate Directory, the phones no longer display Enter More Chars... when
submitting a string that returns no results in the Quick search mode.
49825 When using the Corporate Directory, the black background for the Search bar displays
consistently on different platforms.
49829 NTP Time synchronization is reliable in a particular scenario.
49834 When using the Corporate Directory, if VLV indexing is configured and an Advanced Find yields
more results than the configured page Size (Default is 64), scrolling through the entries works
correctly.
49836 If the Corporate directory is down and the phone reboots, the phones displays a static Please try
again message.
49911 Incoming ring tones are played on the phone in a certain enhanced BLF use case.
49926 The SoundPoint IP 320, 321, 330, and 331 phones no longer auto-increment the new contacts
speed dial index to 100 even though the maximum amount of entries is 99.
49927 After an AdvFind search, exit and re-enter Corp Dir menu, phone displays search bar as Search:
not Search (Filtered) (applies to SoundPoint IP 320,321,330,331 and VVX 1500).
49929 The SoundStation IP 7000 is displays HDX Extension, when voice call type is set to Auto and
phone is not registered to SIP server.
49981 After rebooting the SoundStation IP 7000, the proper HDX extension displays.
49982 The SoundPoint IP 320, 321, 330, and 331 phones reconfigure when DHCP lease expires.
49989 The SoundStation IP 7000 phone is no longer adding contact directories from the call list with the
existing speed dial number.
49977 The SoundPoint IP 320, 321, 330, and 331 phones display the selected status under MyStat
menu.
50090 The SoundStation IP 7000 phone displays an Active Conference screen on joining a remotely
held SLA call without first holding the local call.
Polycom, Inc.
129
Polycom UC Software 4.1.5 Release Notes
50099 Consultative Transfer no longer fails if the second leg is forwarding and its 302 response is
handled by proxy.
50109 Volume levels on the SoundStation IP 7000 are in Sync when Dialing a Video call
50110 An Enter number message displays for Video and audio calls once the Ethernet is removed on
the SoundStation IP 7000.
50115 The DTMF tone of the first digit on the SoundStation IP 7000 plays at the SoundStation IP 7000
volume instead of the HDX volume.
50118 Dial tone volume and Hands Free volume are in sync on the SoundStation IP 7000.
50137 The volume no longer resets to default on the SoundStation IP 7000 after a POTS call is
connected if voice.volume.persists.handsfree=0.
50153 When using the Corporate Directory, setting the Primary Attribute as sticky
dir.corp.attribute.1.sticky=1 gives a clearer user interface behavior.
50159 When using the Corporate Directory, a Quick search on a non-null sticky primary filter is no
longer missing records.
50189 SIP responses are no longer missing the to-tag after the phone challenges INVITE.
50212 Scrolling upward for a while on the Corporate Directory sorts the phone entry list in order.
50253 When using the Corporate Directory on the SoundStation IP 7000and the edit phone number
attribute in AdvFind menu, pressing on the 1/A/a soft key creates an Encoding soft key.
50254 The phone does honors SDP sent in PRACK.
50255 SIP Reliable Provisional responses are retransmitted.
50256 When not yet registered, phones will experience a random delay of 30-60 sec between
registration attempts.
50264 Global prefix +present on calls made from Placed Calls list.
50299 When using the Corporate Directory on the SoundStation IP 7000, Quick search text input starts
at the first multi tap character.
50381 Pressing the left navigation key on the SoundPoint IP 320, 321, 330, and 331 before the
character selection timeout no longer moves cursor 2 spots.
50397 The SoundStation IP 7000 phone displays licenses correctly in the status screen.
50407 When the Corporate Directory server is down with phone connecting to LDAP server, a quick
search results in the phone displaying a proper error message.
50523 When using the Corporate Directory on the SoundPoint IP 320, 321, 330, 331, the phone displays
the Contact title in the View menu.
50546 With URL dialing disabled, a BLIND soft key appears in the third soft key slot after pressing
TRNSFER.
50811 P-Asserted ID display name is a sticky on UI call appearance and in the placed call list.
50869 The phone will only offer SRTP when SRTP crypto suite is selected.
50891 The Resume soft key on the SoundStation IP 6000 and 7000 displays when the phone is put on
hold on another shared line phone.
Polycom, Inc.
130
Polycom UC Software 4.1.5 Release Notes
50989 Receiving a 603 Decline by a BLF monitored user plays a reorder tone.
51041 Regarding X-IdleBrowserSelectUrl, http://url is no longer remembered by the phone.
51245 BLF state is updated on receipt of the first full state NOTIFY after a reboot.
51320 The message Conference in Another Video or phone call? Is no longer displayed in a loop for
each press on Conf hard key (applies to SoundStation IP 7000).
51432 The Conference Hard key Pop-up Message on the SoundStation IP 7000 does not display any
message except directly allowing the user to make a video call.
51554 The phones no longer add an additional CRC to some 802.1X packets received on the PC port.
51567 Server based CFWD/DND sync no longer fails on 3.1.2.0392.
51605 API Push request will no longer be lost if it immediately follows another push request.
51631 The phone releases the first assigned IP address when VLAN is set via DHCP.
51633 The phone plays busy/reorder tone upon a refer-based transfer when it gets a 603 or 486
response.
51644 Certain Japanese strings now display correctly.
51690 The EFK feature is used for one touch Voicemail dialing. When using EFK with SIP 3.1.3, the
phone honors the stickyautolineseize.
51718 The phone no longer continues to ring after a call has been answered with a certain call signaling
sequence.
51763 When adding video to an existing call on a SoundStation IP 7000, pressing the Mute key
successfully mutes the far end.
51838 Japanese characters are properly displayed.
52014/53597 In SIP 3.x.x, when an IP phone picks up a transferred call in a certain scenario, the call is
connected instead of being placed on hold.
52017 The Web interface issue Password entry is masked when entered.
52108 The phone successfully restores destination to Asserted Identity or Remote ID after a transfer
fails.
Configuration File Enhancements
Refer to the following table for a list of the parameters that have been added, changed, or deleted from
the template phone1.cfg and sip.cfg files. You can find further descriptions of parameters in
Administrators’ Guide for the SIP 3.2.0 Release.
Note also that the template file 000000000000.cfg has been modified in order to facilitate support for the
Legacy phones and the VVX 1500 in this release.
Polycom, Inc.
131
Polycom UC Software 4.1.5 Release Notes
Table 19: Software Version 3.2.0 Parameter Enhancements
File
Change
Configuration Parameter
sip
added
sip
added
Old Value
New Value
Description
call.directedCallPickup
Method
native or
See Administrators
Guide for SIP 3.2.0
for details.
call.parkedCallRetrieve
Method
native or
legacy
legacy
sip
added
call.parkedCallRetrieve
String
Star code
See Administrators
Guide for SIP 3.2.0
for details.
sip
added
dialplan.applyToRemote
Dialing
0 or 1;
A flag to determine if
the dial plan applies
to calls made
through the Polycom
HDX system.
dialplan.applyToTelUriDial
0 or 1
sip
added
Default is 0
Default is 1
sip
added
ind.class.2.state.35.index
44
sip
added
ind.class.2.state.36.index
42
sip
added
ind.class.2.state.37.index
43
sip
changed
ind.gi.IP _400.4.physX
122
0
sip
changed
ind.gi.IP _400.5.physX
112
10
sip
changed
ind.gi.IP _4000.6.physH
12
0
sip
changed
ind.gi.IP _4000.6.physW
14
0
sip
changed
ind.gi.IP _4000.6.physX
16
0
sip
changed
ind.gi.IP _4000.6.physY
2
0
sip
changed
ind.gi.IP _450.16.physX
176
196
sip
changed
ind.gi.IP _450.17.physX
176
196
sip
changed
ind.gi.IP _450.18.physX
176
196
sip
changed
ind.gi.IP _450.19.physX
176
196
sip
changed
ind.gi.IP _450.2.physX
40
20
sip
changed
ind.gi.IP _450.3.physH
20
0
sip
changed
ind.gi.IP _450.3.physW
20
0
Polycom, Inc.
A flag to determine if
the dial plan applies
to uses of the tel://
URI.
Changes Relating to
screen layout
modifications.
132
Polycom UC Software 4.1.5 Release Notes
File
Change
Configuration Parameter
Old Value
New Value
sip
changed
ind.gi.IP _450.3.physX
20
0
sip
changed
ind.gi.IP _450.3.physY
2
0
sip
changed
ind.gi.IP _600.13.physH
103
111
sip
changed
ind.gi.IP _600.13.physY
0
25
sip
changed
ind.gi.IP _600.4.physY
105
3
sip
changed
ind.gi.IP _600.6.physH
20
0
sip
changed
ind.gi.IP _600.6.physW
20
0
sip
changed
ind.gi.IP _600.6.physX
113
0
sip
changed
ind.gi.IP _600.6.physY
110
0
sip
changed
ind.gi.IP _7000.3.physH
20
0
sip
changed
ind.gi.IP _7000.3.physW
20
0
sip
changed
ind.gi.IP _7000.3.physX
20
0
sip
added
lcl.ml.lang.menu.1.label
简体中文
(zh-cn)
sip
added
lcl.ml.lang.menu.10.label
日本語
(ja-jp)
sip
added
lcl.ml.lang.menu.11.label
한국어
(ko-kr)
sip
added
lcl.ml.lang.menu.12.label
Norsk
(no-no)
sip
added
lcl.ml.lang.menu.13.label
Polski
(pl-pl)
sip
added
lcl.ml.lang.menu.14.label
Português
(pt-br)
sip
added
lcl.ml.lang.menu.15.label
Сский
(ru-ru)
sip
added
lcl.ml.lang.menu.16.label
Slovenski
(sl-si)
sip
added
lcl.ml.lang.menu.17.label
Español
(es-es)
sip
added
lcl.ml.lang.menu.18.label
Svenska
(sv-se)
Polycom, Inc.
Description
Language selection
displayed in the
appropriate
language.
133
Polycom UC Software 4.1.5 Release Notes
File
Change
Configuration Parameter
sip
added
lcl.ml.lang.menu.2.label
Dansk
(da-dk)
sip
added
lcl.ml.lang.menu.3.label
Nederlands
(nl-nl)
sip
added
lcl.ml.lang.menu.4.label
English
(en-ca)
sip
added
lcl.ml.lang.menu.5.label
English
(en-gb)
sip
added
lcl.ml.lang.menu.6.label
English
(en-us)
sip
added
lcl.ml.lang.menu.7.label
Français
(fr-fr)
sip
added
lcl.ml.lang.menu.8.label
Deutsch
(de-de)
sip
added
lcl.ml.lang.menu.9.label
Italiano
(it-it)
sip
added
log.level.change.lldp
4
Control the logging
detail level for the
LLDP feature.
sip
added
mb.main.autoBackKey
1
See Administrators
Guide for SIP 3.2.0
for details.
sip
changed
ramdisk.minfree
3072
3150
Minimum amount of
free space that must
be left after the RAM
disk has been
created.
sip
changed
se.pat.ringer.13.name
Sampled
1
sip
changed
se.pat.ringer.14.name
Sampled
2
sip
changed
se.pat.ringer.15.name
Sampled
3
sip
changed
se.pat.ringer.16.name
Sampled
4
sip
changed
se.pat.ringer.17.name
Sampled
5
Polycom, Inc.
Old Value
New Value
Description
Customer ringer file
names.
134
Polycom UC Software 4.1.5 Release Notes
File
Change
Configuration Parameter
Old Value
sip
changed
se.pat.ringer.18.name
Sampled
6
sip
changed
se.pat.ringer.19.name
Sampled
7
sip
changed
se.pat.ringer.20.name
Sampled
8
sip
changed
se.pat.ringer.21.name
Sampled
9
sip
changed
se.pat.ringer.22.name
Sampled
10
sip
added
sec.srtp.requireMatchingTag
sip
changed
tone.dtmf.rfc2833Payload
sip
added
sip
added
Polycom, Inc.
New Value
Description
0 or 1
A flag to determine
whether or not to
check the tag value
in the crypto
attribute in an SDP
answer.
127
The phone-event
payload encoding in
the dynamic range
to be used in SDP
offers.
up.idleBrowser.enabled
0 or 1;
default is 0
A flag to determine
whether or not the
background takes
priority over the idle
browser. Used in
conjunction with
up.prioritizeBackgro
und.enable.
up.prioritizeBackgroundMenu
Item.enabled
0 or 1;
default is 1.
If set to 1, the
Prioritize
Background menu is
available to the
user. The user can
then decide whether
or not the
background takes
priority over the idle
browser. Used in
conjunction with
up.idleBrowser.enab
led.
101
135
Polycom UC Software 4.1.5 Release Notes
File
Change
Configuration Parameter
sip
added
sip
New Value
Description
up.screenCapture.enabled
0 or 1;
Default is 0
A flag to determine
whether or not the
user can get a
screen capture of
the current screen
shown on a phone.
The flag is cleared
when the phone
reboots.
added
voice.audioProfile.iLBC.
13_33Kbps.payloadSize
30
sip
added
voice.audioProfile.iLBC.
15_2Kbps.payloadSize
See Administrators
Guide for SIP 3.2.0
for details.
20
sip
added
voice.audioProfile.iLBC.
jitterBufferMax
160
sip
added
voice.audioProfile.iLBC.
jitterBufferMin
40
sip
added
voice.audioProfile.iLBC.
itterBufferShrink
500
sip
added
voice.audioProfile.iLBC.
payloadType
110
sip
removed
voice.audioProfile.Lin16.
44.1ksps.payloadType
sip
added
voice.audioProfile.Lin16.
44_1ksps.payloadType
120
See Administrators
Guide for SIP 3.2.0
for details
sip
added
voice.audioProfile.Lin16.
8ksps.payloadType
116
sip
added
voice.codecPref.iLBC.
13_33Kbps
See Administrators
Guide for SIP 3.2.0
for details
sip
added
voice.codecPref.iLBC.
15_2Kbps
sip
added
voice.codecPref.IP_6000.
iLBC.13_33Kbps
sip
added
voice.codecPref.IP_6000.
iLBC.15_2Kbps
sip
added
voice.codecPref.IP_650.
iLBC.13_33Kbps
Polycom, Inc.
Old Value
120
Parameter renamed.
136
Polycom UC Software 4.1.5 Release Notes
File
Change
Configuration Parameter
sip
added
voice.codecPref.IP_650.
iLBC.15_2Kbps
sip
added
voice.codecPref.IP_7000.
iLBC.13_33Kbps
sip
added
voice.codecPref.IP_7000.
iLBC.15_2Kbps
sip
added
voIpProt.SDP.early.answer
OrOffer
If set to 1, an SDP
offer or answer is
generated in a
provisional reliable
response and
PRACK request and
response.
If set to 0, an SDP
offer or answer is
not generated.
sip
added
voIpProt.SDP.offer.iLBC.
13_33Kbps.includeMode
See Administrators
Guide for SIP 3.2.0
for details.
sip
changed
voIpProt.server.1.port
sip
added
voIpProt.server.2.address
sip
added
voIpProt.server.2.expires
sip
added
voIpProt.server.2.expires.
lineSeize
sip
added
voIpProt.server.2.expires.
overlap
sip
added
voIpProt.server.2.lcs
sip
added
voIpProt.server.2.port
sip
added
voIpProt.server.2.register
1
sip
added
voIpProt.server.2.retryMax
Count
0
sip
added
voIpProt.server.2.retry
TimeOut
0
sip
added
voIpProt.SIP.compliance.RFC
3261.validate.contentLength
Polycom, Inc.
Old Value
New Value
5060
Description
The port of a SIP
server that accepts
registration.
Minimum now 10
30
If set to 1, validation
of the SIP header
content language is
enabled.
137
Polycom UC Software 4.1.5 Release Notes
File
Change
Configuration Parameter
Old Value
New Value
sip
added
voIpProt.SIP.compliance.RFC
3261.validate.uriScheme
If set to 1 or Null,
validation of the SIP
header URI scheme
is enabled.
sip
added
voIpProt.SIP.strictReplaces
Header
This parameter
applies only to
directed call pick-up
attempts initiated
against monitored
BLF resources.
sip
added
voIpProt.SIP.use486for
If set to 1 and the
phone is indicating a
ringing inbound call
appearance, phone
will transmit a 486
response to the
received INVITE
when the Reject soft
key is pressed.
Reject
phone1
added
attendant.behaviors.display
.remoteCallerID.automata
1
phone1
added
attendant.behaviors.display
.remoteCallerID.normal
1
phone1
added
attendant.behaviors.display
.spontaneousCallAppearances
.automata
0
phone1
added
attendant.behaviors.display
.spontaneousCallAppearances
.normal
1
phone1
added
attendant.resourceList.x.
address
The value of
x depends
on the
phone.
For IP 450
x=1-2;
IP 550, 560
x=1-3;
IP 650, 670
x=1-47
Polycom, Inc.
Description
Flags to determine
whether or not
remote party caller
ID information is
presented to the
attendant.
Flags to determine
whether or not a call
appearance is
spontaneously
presented to the
attendant when calls
are alerting on a
monitored resource
The user referenced
by attendant.reg=
will subscribe to this
URI for dialog.
138
Polycom UC Software 4.1.5 Release Notes
File
Change
Configuration Parameter
phone1
added
attendant.resourceList.x.
label
phone1
added
attendant.resourceList.x.
type
normal
phone1
changed
attendant.ringType
1
phone1
added
dialplan.1.applyToTel
UriDial
1
phone1
added
dialplan.2.applyToTel
UriDial
1
phone1
added
dialplan.3.applyToTel
UriDial
1
phone1
added
dialplan.4.applyToTel
UriDial
1
phone1
added
dialplan.5.applyToTel
UriDial
1
phone1
added
dialplan.6.applyToTel
UriDial
1
phone1
changed
divert.noanswer.1.timeout
60
55
phone1
changed
divert.noanswer.2.timeout
60
55
phone1
changed
divert.noanswer.3.timeout
60
55
phone1
changed
divert.noanswer.4.timeout
60
55
phone1
changed
divert.noanswer.5.timeout
60
55
phone1
changed
divert.noanswer.6.timeout
60
55
phone1
added
reg.1.server.2.address
phone1
added
reg.1.server.2.expires
phone1
added
reg.1.server.2.expires.
lineSeize
phone1
added
reg.1.server.2.expires.
overlap
phone1
added
reg.1.server.2.lcs
phone1
added
reg.1.server.2.port
phone1
added
reg.1.server.2.register
Polycom, Inc.
Old Value
New Value
Description
Text label to appear
on the display
adjacent to the
associated line key
Type of resource
being monitored.
When present, and
if dialplan.x.digitmap
is not Null, this
attribute overrides
the global dial plan
defined in the
sip.cfg
configuration file.
Modified No Answer
Timeout
See Administrators
Guide for SIP 3.2.0
for details
139
Polycom UC Software 4.1.5 Release Notes
File
Change
Configuration Parameter
phone1
added
reg.1.server.2.retryMax
Count
phone1
added
reg.1.server.2.retryTimeOut
phone1
added
reg.2.musicOnHold.uri
phone1
added
reg.2.server.1.lcs
phone1
added
reg.2.server.2.address
phone1
added
reg.2.server.2.expires
phone1
added
reg.2.server.2.expires.line
Seize
phone1
added
reg.2.server.2.expires.over
lap
phone1
added
reg.2.server.2.lcs
phone1
added
reg.2.server.2.port
phone1
added
reg.2.server.2.register
phone1
added
reg.2.server.2.retryMax
Count
phone1
added
reg.2.server.2.retryTimeOut
phone1
added
reg.2.tcpFastFailover
phone1
added
reg.3.musicOnHold.uri
phone1
added
reg.3.server.1.lcs
phone1
added
reg.3.server.2.address
phone1
added
reg.3.server.2.expires
phone1
added
reg.3.server.2.expires.line
eize
phone1
added
reg.3.server.2.expires.
overlap
phone1
added
reg.3.server.2.lcs
phone1
added
reg.3.server.2.port
phone1
added
reg.3.server.2.register
phone1
added
reg.3.server.2.retryMax
Count
phone1
added
reg.3.server.2.retryTimeOut
Polycom, Inc.
Old Value
New Value
Description
140
Polycom UC Software 4.1.5 Release Notes
File
Change
Configuration Parameter
phone1
added
reg.3.tcpFastFailover
phone1
added
reg.4.musicOnHold.uri
phone1
added
reg.4.server.1.lcs
phone1
added
reg.4.server.2.address
phone1
added
reg.4.server.2.expires
phone1
added
reg.4.server.2.expires.line
Seize
phone1
added
reg.4.server.2.expires.
overlap
phone1
added
reg.4.server.2.lcs
phone1
added
reg.4.server.2.port
phone1
added
reg.4.server.2.register
phone1
added
reg.4.server.2.retryMax
Count
phone1
added
reg.4.server.2.retryTimeOut
phone1
added
reg.4.tcpFastFailover
phone1
added
reg.5.musicOnHold.uri
phone1
added
reg.5.server.1.lcs
phone1
added
reg.5.server.2.address
phone1
added
reg.5.server.2.expires
phone1
added
reg.5.server.2.expires.line
Seize
phone1
added
reg.5.server.2.expires.
overlap
phone1
added
reg.5.server.2.lcs
phone1
added
reg.5.server.2.port
phone1
added
reg.5.server.2.register
phone1
added
reg.5.server.2.retryMax
Count
phone1
added
reg.5.server.2.retryTimeOut
phone1
added
reg.5.tcpFastFailover
Polycom, Inc.
Old Value
New Value
Description
141
Polycom UC Software 4.1.5 Release Notes
File
Change
Configuration Parameter
phone1
added
reg.6.musicOnHold.uri
phone1
added
reg.6.server.1.lcs
phone1
added
reg.6.server.2.address
phone1
added
reg.6.server.2.expires
phone1
added
reg.6.server.2.expires.line
Seize
phone1
added
reg.6.server.2.expires.
overlap
phone1
added
reg.6.server.2.lcs
phone1
added
reg.6.server.2.port
phone1
added
reg.6.server.2.register
phone1
added
reg.6.server.2.retryMax
Count
phone1
added
reg.6.server.2.retryTimeOut
phone1
added
reg.6.tcpFastFailover
Old Value
New Value
Description
Understanding Updates to SIP 3.1.7
This section lists additions and changes, removals, enhancements, and configuration file parameter
changes to SIP 3.1.7 beside their respective Polycom tracking ID number.
New or Enhanced Features
61028 Added support for SoundPoint IP 430.
61547 The phones now send a 486 (Busy) response to a received INVITE message when a call is
rejected.
Enhanced Capabilities
51718 Under certain configurations, phone no longer continues to ring after the call has been answered.
52968 Deleted instant messages can be removed from the main screen.
53975 The phones send a SUBSCRIBE message in a certain scenario when using an SCA with bargein enabled.
55884 The displays on a SoundPoint IP 650 with expansion modules no longer freeze during a
consultative transfer.
Polycom, Inc.
142
Polycom UC Software 4.1.5 Release Notes
58689 The phones no longer send a 486 if an INVITE is received after a NOTIFY for the alerting state
and the configuration parameter callsPerLineKey is set to 1.
58728 The phone presents the New Call soft key and the End Call soft key to allow the user to release
the call and place the phone into idle state after hanging up the call during a consultative transfer.
59789 On the SoundPoint IP 650, the user is able to properly resume a held call after answering a
different call.
60051 On the SoundPoint IP 650 using a BLA, the display does shows the status of the remotely held
call while there is an active call currently displayed. Pressing the Down Arrow key followed by the
Up Arrow key refreshes the display to properly show the status of the held call.
60141 On the SoundPoint IP 650, on a Bridged Line Appearance BLA line, the display incorrectly
indicates 2 call appearances when there should only be one for the active call. The 2nd call
appearance is for the previously held remote call that is no longer on hold.
60145 On the SoundPoint IP 650 using a BLA, the display on the phone correctly presents 2 call
appearances instead of only one.
60177 The display on the SoundPoint IP 5xx and 6xx presents hot-dialed digits when the idle display
feature is enabled.
60264 During a call using a BLA line, when the display is showing the dialing screen, remote call
appearances are no longer displayed when the remote phones BLA line resumes a call.
60340 The Join soft key no longer displays for phones with BLA lines when there is only one call active
on the phone.
60480 A phone monitoring other BLA lines show the presence (LED goes out) of a BLA line when that
monitored line joins two other calls.
60756 A phone monitoring a Shared Call Appearance line presents a correct presence indication of a
BLA line when that monitored line joins two other calls in a centralized conference.
61264 Calls placed on hold using a shared BLA line timeout when a remote phone picks up the held call
(on the BLA line).
61283 When a user attempts to place a conference call on hold and the phone receives a 400 Bad
request. The phone no longer sends a NOTIFY with <parampname=+sip.rendering pvalue=no />.
61298 When 1.2Mbps of multicast traffic is passed through the PC port on the SoundPoint IP 601
phone, the data port no longer experiences a packet loss of 17%.
61299 When a phone has established a centralized conference call, the user is able to transfer a third
incoming call.
61321 When a phone joins a centralized conference bridge, other monitoring phones correctly show the
BLA line as being on hold instead of being in use.
61547 The phone sends a 486 Busy message when a call (INVITE) is rejected. A binary configuration
parameter is added to sip.cfg called voIpProt.SIP.use486forReject. By default,
(parameter is 0) the feature is disabled. If the parameter equals 1, the feature is enabled. If
enabled and the phone is indicating a ringing inbound call appearance, then upon pressing the
Reject soft key, the phone will transmit a 486 Response to the originator of the received INVITE
message.
61725 Users can pick up a held call after multiple hold/resume interactions on the phone.
Polycom, Inc.
143
Polycom UC Software 4.1.5 Release Notes
61950/62024 The phone honors a retry-after header in a 500 Glare message responding to a BLA reSUBSCRIBE message.
62036 The SoundPoint IP 3xx phone continues sending DTMF RTP EVENTS when receiving a second
incoming call while it is already active on a previously established call.
62050 The SoundPoint IP 650 phone properly updates the number of held calls after sending 200 OK
messages as part of the notifications process.
62127 The Blind transfer soft key on the SoundPoint IP 650 is presented on the display when the
Transfer soft key is pressed on the second call.
62223 The phone no longer crashes after resuming a held call using a BLA.
62226 The phone no longer proceeds to join a conference after receiving a 403 Forbidden from the
switch.
62262 The phone no longer establishes a 1-way audio path after it has re-established a centralized
rd
conference call with the dropped 3 party. This behavior is observed with Sylantro switches.
62279 The presence indicator on a Bridged Line Appearance displays correctly after the phone receives
a 486 message.
62313 Using a BLA configuration, a dial tone is present when pressing the second line key followed by
lifting handset after holding a call on first line appearance.
62361 The call status on a BLA Bridged Line Appearance (configured for 1 call per line appearance) of a
monitoring phone is updated correctly when transfer/conference soft key is pressed.
62435 The SoundPoint IP 650 phone correctly displays a call appearance labeled Unknown Party if the
remote party is held while reorder tone is played locally.
62511 In certain situations, the monitored Busy Lamp Field line invokes an incoming call notification
(icon and tone).
62514 In certain situations, the status of the monitored Busy Lamp Field lines on the SoundPoint IP 670
is removed from the display even though the status has been updated by the switch.
62569 The phone no longer generates a redundant NOTIFY message when triggered by a 100
response during a re-INVITE.
62669 When multiple phones try to resume a held Bridge Line Appearance BLA line at the same time,
the presence indicator on the BLA line is preserved on the trailing phone when the reorder tone is
played.
62672 Either Directed Call Pickup DCP or Group Call Pickup feature (using soft keys instead of *53 and
*54 feature access codes) no longer fail when the user enters an account code. The account
code is appended to the user portion of the URI.
62704 The presence indicator of a Bridged Line Appearance BLA is updated correctly on monitoring
phones when the phones LAN data cable is disconnected and then re-connected.
62926 The Resume soft key on the SoundPoint IP 3xx displays when the line key is pressed
continuously while the line is in a remote held call state. This occurs when the line is configured
as callsPerLineKey=1.
Polycom, Inc.
144
Polycom UC Software 4.1.5 Release Notes
63099 The phones monitoring Bridged Line Appearance BLA line, configured for one call per line, can
pick up the held call after the call on a BLA line has been put on hold using the
Transfer/Conference key.
63286 The phone’s Part Number is listed correctly instead of YYYY-YYYYY-YYY.
64212 Invoking the Call Park feature with the soft key on the SoundPoint IP 3xx functions correctly when
the soft key is configured as 1 line and 1 call per line.
64219 The SoundPoint IP 3xx phone sends a proper hold NOTIFY message after a consultative transfer
is canceled when the configuration parameter notifyTransferHoldAsActive is disabled.
64271 In an attempt to answer an incoming call, the call is no longer unintentionally terminated. This
occurs when the incoming calls line key is pressed simultaneously as the handset is lifted.
64274 In an attempt to resume a held call, the held call is no longer unintentionally terminated when the
user inadvertently seizes two line keys simultaneously.
64327 In an attempt to answer an incoming call with the user inadvertently pressing 2 line keys, the user
is no longer connected to both lines one with an incoming caller on one and a dial tone on the
other.
64340 The indicator, on a Bridged Line Appearance BLA line that is monitoring other lines, blink after the
monitored phone performs the following sequence: Transfer > Split > EndCall > Resume > Hold.
64356 The display on the SoundPoint IP 3xx showing a remote call appearance times out when the user
presses continuously a BLA line key followed by pressing a down arrow key while there are
multiple calls on hold on the remote BLA.
64822 When configuring the SoundPoint IP 3xx phones using sip_att.cfg, the phone no longer shows
Service Unavailable when the speed dial key is pressed while the phone is off-hook.
64862 Joining an internal extension with an external PSTN call no longer causes one call to drop.
65119 When a Bridged Line Appearance BLA line is presented in a dialing screen, the remote call
appearance is correctly displayed when the remote BLA line resumes a call.
65207 A slow memory leak due to the receipt of hunt group INVITE containing replaces no longer occurs
in the SIP stack.
67186 All soft keys on the SoundPoint IP 301, 501, and IP 601 no longer disappear on the assistant
phone when pressing down the arrow key after placing multiple calls on hold with the boss line
appearance.
Configuration File Enhancements
Refer to the following table for a list of enhancements made to software version 3.1.7 configuration file
parameters.
Table 20: Software Version 3.1.7 Parameter Enhancements
File
Action
Parameter
Modification Description
sip
added
voIpProt.SIP.use486forReject
Defaults to null
sip
added
call.localConferenceEnabled=1
Defaults to 1
Polycom, Inc.
145
Polycom UC Software 4.1.5 Release Notes
Polycom, Inc.
146
Known Issues and Suggested
Workarounds
The following issues are known to be present in the current release. They will be reviewed for possible
fixes in a future release if no reasonable workaround is available.
26615 Subnet mask forces all packets through gateway when not using DHCP and when using the
wrong subnet mask for the network class in use. For example, using 192.168.X.X addresses with
a 255.255.0.0 subnet mask. Exists in SIP 1.4.x.
Workaround: Use the correct subnet mask.
26920 Centralized conference fails due to RTP port opening too slowly in some cases.
Workaround: No workaround is currently available.
30086 Boot servers running explicit FTPS are not supported.
Workaround: Use implicit FTPS or HTTPS.
30371 Pattern generator for tones does not work well in the case of a single repeating chord.
Workaround: Start the pattern with a short period of silence followed by the desired initial chord.
Loop back to the desired initial chord instead of the initial silence.
33445 LCS Presence and dialing from Buddy Lists does not work across federations.
Workaround: To dial contacts across federations, program a speed dial with the SIP URI of the
contact. There is no workaround for watching Federated Buddy status from the phone.
37175 If configuration files are used to set the SNTP server address, date validity checking on CA
certificates will be ignored for https provisioning.
Workaround: Set the SNTP server address through the phone UI or use DHCP to inform the
phone of the SNTP server address.
37273 If the custom idle display and idle browser features are both enabled, the phone UI displays
incorrectly.
Workaround: Do not set ind.idleDisplay.enabled=1 and enable the Idle Browser at the
same time.
37984 Enabling the Idle bit-map on SoundPoint IP 330 and 320 phones causes the Line Key labels and
dialed digits to be invisible.
Workaround: Do not use the idle bit-map on 330/320 phones; instead, set
ind.idleDisplay.enabled=0.
41993 Scrolling through the Corporate Directory may not return complete results if results contain
Unicode character values > 127 (server does not support sorting).
Workaround: Start the search in a different location or avoid use of Unicode characters >127 in
directories.
42027 In certain scenarios, the time-stamping in log files of a SoundStation IP 7000 that is used as a
secondary/slave device is incorrect.
Workaround: As of SIP 3.1.0 the occurrence of this issue only relates to the treatment of Daylight
savings Time settings.
147
Polycom UC Software 4.1.5 Release Notes
44764 SRTP processing may cause performance degradation with certain video/audio codec
combinations on the VVX 1500.
Workaround: If SRTP is being used, limit the video bit rate to 384 Kbps.
46997 Camera brightness adjustment does not work between levels 3 to 6 on the VVX 1500.
Workaround: No workaround is currently available.
48905 Jitter parameter is not correctly computed on the SoundStation IP 6000/7000 as per RFC3550.
Workaround: No workaround is currently available.
52141 Daisy-chained SoundStation IP 7000 phones sometimes become stuck during software upgrade.
Workaround: Pressing any key on the phone will continue the upgrade.
52142 Video connections with CounterPath Eyebeam client on the VVX 1500 do not work if H.263-1998
codec is selected. This was experienced with Eyebeam version 1.5.19.5 build 52345.
Workaround: Try using a different codec. Try other versions of Eyebeam client as some do work.
53514 H.264 calls to an HDX9002 device using an MGC 50 Gateway using H.320 result in lip sync
issues (applies to VVX 1500).
Workaround: Set the call for transcoding on the MGC.
54027 The receiving phone does not re-invite with a new key at the half-life of the key life-time.
Workaround: Ensure that both ends use the same key life time so that the sending phone will
initiate a key re-negotiation.
54028 Key changes do not function correctly when multiple crypto suites are enabled.
Workaround: Configure a single crypto suite on the phone.
54321 The VVX 1500 does not receive video (does receive audio) when calls are initiated from a
Tandberg C20 (running 2.0.0.191232) device using SIP.
Workaround: No workaround is currently available.
54799 The VVX 1500 transmits H.264 QCIF video to Tandberg MXPs in H.323 calls.
Workaround: Set the video bit rate on the VVX 1500 to 512 Kbps to avoid the issue.
54976 H.264 calls to a Tandberg Edge95 MXP device using a Tandberg Gateway using encrypted
media (offered but not required) results in distorted audio and no video on the VVX 1500.
Workaround: Configure system for encryption required.
54977 H.264 calls to a Tandberg Edge95 MXP device using a Tandberg Gateway result in lip sync
issues on the VVX 1500.
Workaround: No workaround is currently available.
59812 Blind transfer to a URL is not successful on the SoundStation IP 7000. Eventually, the URL soft
key becomes unavailable.
Workaround: No workaround is currently available.
61091 The configuration parameter tcpIpApp.port.rtp.forceSend=1024 works only for the
SoundStation IP 6000, 7000 and VVX 1500. It does not function properly for SoundPoint IP
phones.
Workaround: No workaround is currently available.
Polycom, Inc.
148
Polycom UC Software 4.1.5 Release Notes
62387 Adding a new line registration to a phone with BLF causes the notifications (ringing) for the BLF
line to display on the previous line. Introduced in UC software 3.3.1
Workaround: A phone reset will resolve the issue.
62482 Server certificate Serial Number is checked against the host name if the outbound proxy is
configured.
Workaround: No workaround is currently available.
63123 Instead of initiating a new call, an attendant phone plays a reorder tone when a BLF line key is
pressed for the second time.
Workaround: No workaround is currently available.
63527 The phone sends out INVITE and CANCEL if no provisional response is received.
Workaround: No workaround is currently available.
63609 Cannot answer a call using the speaker soft key when DND is enabled and
call.rejectBusyOnDnd is set to zero (applies to SpectraLink 84xx).
Workaround: No workaround is currently available.
66251 British Telecom Caller ID type is not correctly supported (applies to SoundStation Duo).
Workaround: No workaround is currently available.
68815 The phone does not send a CallState=CallConference notification when a conference is
established (applies to all SoundPoint IP and SpectraLink 84xx).
Workaround: No workaround is currently available.
69502 Confirm Click-to-dial text does not appear on the SoundPoint IP 331 phone when SNTP fails.
Workaround: Configure SNTP.
69552 Music on hold (MOH) call dialog does not get terminated when there is an update from the MOH
server.
Workaround: End the call to restore normal state.
69735 When the phone is registered with a H.323 line, DTMF digits are not sent in the Tel URI call with
Ext and Postd options (applies to VVX 500, 1500).
Workaround: No workaround is currently available.
69898 Quick search bar on the SoundPoint IP 321, 330, 331, and 355 only accept 15 characters when
the corporate directory is configured.
Workaround: No workaround is currently available.
70480 When the phone is using the Polycom Desktop Connector, the keyboard arrow keys do not
support active and inactive call navigation (applies to VVX 500).
Workaround: No workaround is currently available.
70728 Software Upgrade does not work if <partnumber>.xml file is not specified as a part of
upgrade.custom.server.url configuration value.
Workaround: Ensure the part-number.xml file is part of the upgrade.custom.serverurl
configuration value.
71386 Soft keys URIs do not function when the phone is in the Enter Number screen (applies to VVX
1500).
Polycom, Inc.
149
Polycom UC Software 4.1.5 Release Notes
Workaround: No workaround is currently available.
71800 Users cannot change the user password using the Web Configuration Utility.
Workaround: Use the phone’s user interface to change the user password.
72082 The phones do not detect a server certificate status change from REVOKED to GOOD until the
phone is rebooted (applies to SoundPoint IP 321, 331, 450, 550, 560, 650, and 670, and
SoundStation 5000.)
Workaround: No workaround is currently available.
72211 An explicitly trusted Intermediate CA fails TLS verification when it is the issuer of a server
certificate.
Workaround: No workaround is currently available.
72242 The phone is not able to connect to radius server when configured with EAP method as PEAP
and inner authentication as GTC (applies to VVX 500).
Workaround: Recommend to use Cisco ACS server 5.1 or higher.
72299 When the SoundPoint IP 450, 560, 650 phones are registered with BLA lines, they continue to
display remote hold appearances even after the remote BLA resumes the call.
Workaround: No workaround is currently available.
72387 After pressing the Transfer soft key, the remote BLA line does not show remote hold status when
call.shared.exposeAutoHolds is set to 1.
Workaround: No workaround is currently available.
72601 The SoundPoint IP 33x phones fail to dial authorized call when in the Phone Locked state.
Workaround: No workaround is currently available.
72677 When a NOTIFY message with a higher version is sent, the phone re-subscribes to the server
and gets a NOTIFY with the correct version, but fails to update the dialog with the state (applies
to SoundPoint IP 450/560/650).
Workaround: No workaround is currently available.
72898 Hard key external URL mapping requires EFK enabled on the SoundPoint IP 650.
Workaround: Enable EFK using configuration files.
73015 The LifeSize Team 220 behaves incorrectly by remaining in a connecting state when there is a
call from VVX 1500 over H323.
Workaround: No workaround is currently available.
74120 Plantronics Audio 646 DSP USB headset volume control does not work (applies to VVX 500).
Workaround: Adjust the volume using the volume keys on the phone.
74533 A phone configured with a Synergy call server displays the incorrect caller ID on the UI for an
incoming call (applies to VVX 1500).
Workaround: No workaround is currently available.
74650 In an active audio-only call between a PC client and a VVX 1500, the far-end video never starts
on the PC client when a user presses Add Video.
Workaround: No workaround is currently available.
74763 The MKC5 key to upload logs does not work (applies to SoundStation Duo).
Polycom, Inc.
150
Polycom UC Software 4.1.5 Release Notes
Workaround: No workaround is currently available.
74901 When the lock feature is enabled after phone reboot, the emergency/authorized call list is not
displayed when the user tries to place a call using headset/speaker key.
Workaround: No workaround is currently available.
74958 When DND is enabled, the phone is missing the call forward message Fwd:<number> (applies to
VVX 500, 1500, and SpectraLink 84xx).
Workaround: No workaround is currently available.
75157 A phone configured with a Synergy call server displays the incorrect soft keys after a “Conference
service unavailable” error is shown. This exists in UC software 3.3.3.
Workaround: No workaround is currently available.
75195 Hold/Transfer/Conference does not display when the parameter
softkey.feature.basicCallManagement.redundant = 0 (applies to SoundStation
Duo).
Workaround: No workaround is currently available.
75229 A phone configured with a Synergy call server displays the local conference UI when establishing
a centralized conference using the Join soft key.
Workaround: No workaround is currently available.
75427 The Unified Call Appearance List (UCAL) filtered view times out to the default UCAL view when a
user scrolls the filtered list and does not change the focus (applies to VVX 500).
Workaround: No workaround is currently available.
75591 In the Lync environment, when the user logs out, the phone does not logout all the user login
credential-dependent applications.
Workaround: No workaround is currently available.
75661 The multi-key combination shortcuts for uploading logs and rebooting the phone sometimes do
not work (applies to VVX 500).
Workaround: No workaround is currently available.
75671 When parking a call from the Favorites menu, the call park input dialog (where users enter a park
extension) disappears (applies to VVX 500).
Workaround: No workaround is currently available.
75759 Numeric data entered using the dialpad on the phone browser cannot be deleted using the
dialpad.
Workaround: Use the virtual keyboard.
75778 Using Microsoft Lync, if a user dials an invalid extension, the entry is sometimes not logged in the
Placed Calls call list.
Workaround: No workaround is currently available.
75869 Changing the local contact directory search option from first name to last name and vice versa
causes the Restart and Save soft keys to disappear on the phone.
Workaround: Exiting and re-entering the directory.
75898 Pressing the App hard key on the phone and trying to dial the highlighted/focused SIP/Tel URI
does not work with the microbrowser (applies to VVX 1500 and VVX 500).
Polycom, Inc.
151
Polycom UC Software 4.1.5 Release Notes
Workaround: No workaround is currently available.
76468 In the Premium ACD, Call Agent state changes from Unavailable to Available after a phone
reboot. This could be an interoperability issue with the call server.
Workaround: No workaround is currently available.
76522 In the hoteling call center feature, the phone does not display the status of the call center when
there is a special character in the call center name.
Workaround: The call center administrator can set the call center name.
76655 Using a star (*) in the dial string on the SoundStation IP 7000 causes the phone to send the star
as a dot (.) to the HDX video end points.
Workaround: Two stars (**) should be used.
76753 Removing a BLF line from the server causes the speed dial icon to disappear.
Workaround: Restart or reboot the phone, and the icon will re-appear.
76881 On a shared call, the reorder tone is not played to the user when a Resume attempt fails.
Workaround: No workaround is currently available.
76977 Adding a new registration line changes the BLF-monitored lines label from first/last name to its
extension number.
Workaround: Reboot the phone.
77039 When PTT is enabled, sender name/ID, updated through the parameter reg.x.displayname,
does not get updated during the PPT call.
Workaround: No workaround is currently available.
77076 When the XT9 input mode is enabled, the phone displays unmatched UIMA-focused items in the
st
1 position during XT9 (PinYin) input.
Workaround: No workaround is currently available.
77195 Reboots occur occasionally if the roaming contacts exceeds 100 on the SoundPoint IP and 200
on VVX phones.
Workaround: No workaround is currently available
78232 During a remote conference pickup on a shared line, the phone does not display the call
appearance and call indicator.
Workaround: No workaround is currently available.
78340 Sending several MWI NOTIFY messages within a few seconds of each other may cause the
phone to reset.
Workaround: Avoid sending multiple MWI messages close together.
79634 During paging, the receiving phone displays the MAC address of the sender instead of the caller
ID.
Workaround: Try restarting the phone.
79735 Changing the language of the phone from German to any other language (other than English)
may result in a display of diacritic letters (applies to VVX 500 and SoundPoint 331).
Workaround: Try changing the language to English first.
Polycom, Inc.
152
Polycom UC Software 4.1.5 Release Notes
80212 In a Lync environment, when the corporate directory and parameter dir.corp.sortcontrol
are enabled, the contact search does not fetch any contacts.
Workaround: Set the parameter dir.corp.sortcontrol=0.
80227 The phone does not display the saved name of the contact in the local contact directory.
Workaround: Use the full URI while adding the contacts in the local contact directory.
81272 When the held call is transferred to a CX 600 phone, the call will be established as a one-way call
on the far end.
Workaround: Try hold/resume on the CX 600 to establish a two-way call.
81315 The call logs of the first user are available on the phone when a new user logs in without signing
out the first user.
Workaround: No workaround is currently available.
82030 When the Calendar is configured on the phone and the active directory credentials are changed
by the user/admin, the phone fails to register to Lync server.
Workaround: The user needs to register the phone manually with the correct credentials.
82043 When a Lync profile is used along with the bootserver, any changes performed to the MAC.cfg
file using XML notepad and uploaded to the phone will cause the phone to deregister. The xml
notepad adds an extra space in the certificate which makes the certificate invalid and causes the
phone to deregister.
Workaround: Use VI editor or Edit Plus editor.
82212 Immediately answering a call on a phone which is outside the enterprise (remote
worker/federation scenario) when the UDP is blocked by a firewall, may result in a reboot (applies
to SoundPoint IP 321/331).
Workaround: No workaround is currently available.
82302 In a CAC (Call Admission Control) scenario, when a call transfer fails from the phone to remote
Lync client, the phone is unable to resume the call.
Workaround: Try doing consultative transfer.
82401 The call order widget disappears on the phone screen after scrolling through five of the maximum
number of calls (24).
Workaround: No workaround is currently available.
82873/82877 The phone fails to update its presence state when it is trying to dial out the emergency call
number 911.
Workaround: No workaround is currently available.
83101 In a federated environment, when the UDP traffic is blocked on the firewall, the phone may fail to
connect the calls.
Workaround: No workaround is currently available.
83157 The phone does not display the protocol field for the local contacts.
Workaround: No workaround is currently available.
83875 In a conference call scenario, the first phone connected to the conference does not transmit video
when joined in a H.323 video conference call to a Cisco SX20 IMCU (applies to VVX 500 and
VVX 600).
Polycom, Inc.
153
Polycom UC Software 4.1.5 Release Notes
Workaround: No workaround is currently available.
83884 The VVX phone displays a gray image when a video call is established with Grandstream Video
phone using DMA server.
Workaround: Use a bit rate of 512 Kbps or 384 Kbps, or reduce the packet size to 1200.
83888 In a conference call scenario, the first phone connected to the conference does not transmit video
when joined in a H.323 conference call to a HDX 8006 at a bit rate of 768 Kbps.
Workaround: Use any other bit rate except 768 Kbps, i.e., 384, 512, 1024, etc.
83887/83889 VSX displays a blank or reduced image in a video call with VVX when the phone is
transmitting at a bit rate of 384 Kbps or 786 Kbps.
Workaround: Use H.263 video codec with a bit rate greater than 1500 Kbps.
83910 An elongated video displays on the phone when it receives video at bit rates greater than 512
Kbps from a “Real Presence Mobile” client.
Workaround: No workaround is currently available.
84061 In a call center scenario, the phone does not display the call center information on the default
screen when the VVX Camera is attached.
Workaround: Press the call center info soft key to retrieve the related information.
84125 The phone is unable to switch the call mode from audio-video to audio only in SIP protocol when
auto routing is enabled and feature.audioVideoToggle.enabled=1 is set (applies to VVX
500 and VVX 600).
Workaround: Select SIP protocol manually from the protocol menu to switch phone from video
mode to audio only mode.
84450 An incorrect pop-up error message "DHCP failed" displays on the phone's screen, instead of
"Duplicate IP", when the phone detects a duplicate IP.
Workaround: No workaround is currently available.
84598 When a Lync user saves contacts locally on the phone, the contacts are displayed on the screen
even after the user signs out and a second user signs in.
Workaround: Reboot the phone after the second user signs in.
85011 In a Push-to-Talk (PTT)/Paging scenario and when navigating with the arrow keys, the active
page does not go to the waiting state when the Talk soft key is released.
Workaround: Browse through the menu again after releasing the Talk soft key.
85154 An error pop-up message does not display on the phone’s screen when the user tries to play an
unsupported media file on the phone’s microbrowser.
Workaround: No workaround is currently available.
84795 A pop-up message covers the details view of the contacts on the phone when the user tries to
add a contact to favorites (applies to VVX 300/310).
Workaround: No workaround is currently available.
84774 Calls are displayed in the Call logs menu according to the logging time.
Workaround: No workaround is currently available.
84692 The sign-in pop-up message takes slightly longer (~30s) to display when a Lync user reboots the
phone after a few contacts (~15) are pinned to “frequent contacts” (applies to VVX 300/310).
Polycom, Inc.
154
Polycom UC Software 4.1.5 Release Notes
Workaround: No workaround is currently available.
85606 Setting DND presence state from the “UC-One Application” or “My status” menu doesn't set the
local DND to ON.
Workaround: No workaround is currently available.
86113 Favorite contacts appear on the phone screen even after the parameter
feature.broadsoftdir.enabled is set to 0.
Workaround: Set feature.broadsoftUcOne.enabled to 0.
86172 Adding or deleting or editing the BroadSoft directory contact from the phone is not available.
Workaround: No workaround is currently available.
87611 The phone’s screen turns off when the dial tone times out after the configured time and the
parameters powerSaving.idleTimeout.userInputExtension=1 and
call.dialtoneTimeOut=180 are configured.
Workaround: No workaround is currently available.
88312 The phone displays some menus, e.g., ring type list, network diagnostics, in English instead of
the configured language.
Workaround: No workaround is currently available.
Polycom, Inc.
155
Reference Documents
This section lists all documents referred to in these release notes as well as other relevant documents.
For information and support for all Polycom voice products and software, and for access to supporting
documentation, see Polycom UC Software Support Center.
Polycom UC Software Administrators’ Guide
Polycom UC Software 4.1.0 Administrators’ Guide
Technical Bulletins, Quick Tips, White Papers, and Engineering Advisories
Feature Profile 84393: Using the Polycom BroadSoft UC-One Application on Polycom VVX Business
Media Phones
White Paper: Configuration File Management on Polycom® SoundPoint® IP, SoundStation® IP, and
VVX® Phones
Technical Bulletin 35311: Maintaining Older Polycom® Phones Beyond Their Last Supported Software
Release
Technical Bulletin 39358: Using Custom Ringtones on Polycom® SoundPoint® IP, SoundStation® IP,
and Polycom VVX® 1500 Phones
Technical Bulletin 52609: Mutual Transport Layer Security Provisioning Using Microsoft® Internet
Information Services 6.0
Technical Bulletin 56449: Polycom® SoundPoint® IP /SoundStation® IP /VVX® Software Changes in the
Next Release
Quick Tip 57215: Phone Lock Feature on Polycom® Phones Running Polycom UC Software
Technical Bulletin 60519: Simplified Configuration Enhancements in Polycom® UC Software 3.3.0
Engineering Advisory 64731: Polycom® UC Software 4.0.x: Upgrade and Downgrade Methods
Technical Bulletin 66743: Security Advisory Relating to Denial of Service Vulnerability on Polycom®
SoundPoint® IP and SoundStation® IP Phones
Feature Profile 72430: Using Polycom Phones with Microsoft Lync Server 2010
User Guides
SoundPoint IP Phones
SoundStation IP Phones
VVX Business Media Phones
Miscellaneous
SIP/UC Software Downloads Matrix
156
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising