004-3039-272
MULTI-NET® CONSOLE SETUP INSTRUCTIONS
Third Printing
September 1995
Supersedes Part No. 004-3039-271 1-93
Part No. 004-3039-272
9-95mwp
Printed in U.S.A.
MULTI-NET® CONSOLE
SETUP INSTRUCTIONS
Copyright 1995 by the E.F. Johnson Company
The E.F. Johnson Company designs and manufactures two-way radio equipment to serve a wide variety of communications needs. Johnson produces equipment for the mobile telephone and land mobile radio services which include
business, industrial, government, public safety, and personal users. In addition, Johnson designs and manufactures
electronic components used in communications equipment and other electronic devices.
LAND MOBILE PRODUCT WARRANTY
The manufacturer’s warranty statement for this product is available from your product supplier or from the E.F.
Johnson Company, 299 Johnson Avenue, Box 1249, Waseca, MN 56093-0514. Phone (507) 835-6222.
WARNING
This device complies with Part 15 of the FCC rules. Operation is subject to the condition that this device does not
cause harmful interference. In addition, changes or modification to this equipment not expressly approved by E. F.
Johnson could void the user’s authority to operate this equipment (FCC rules, 47CFR Part 15.19).
DO NOT allow the antenna to come close to or touch, the eyes, face, or any exposed body parts while the radio is
transmitting.
DO NOT operate the radio near electrical blasting caps or in an explosive atmosphere.
DO NOT operate the radio unless all the radio frequency connectors are secure and any open connectors are properly
terminated.
DO NOT allow children to operate transmitter equipped radio equipment.
SAFETY INFORMATION
Proper operation of this radio will result in user exposure below the Occupational Safety and Health Act and Federal
Communication Commission limits.
The information in this document is subject to change without notice.
® Multi-Net is a registered trademark of the E.F. Johnson Company.
TABLE OF CONTENTS (CONT.)
1
INTRODUCTION
1.1
1.2
1.3
1.4
1.5
1.6
1.7
SCOPE OF THIS MANUAL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
MULTI-NET CONSOLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
AUDIO INTERFACE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
911 INTERFACE MODULE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
UNSELECT AUDIO PERSONALITY CARD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
CONSOLE MANAGER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
CONSOLE USER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
2
CONSOLE SCREEN LAYOUT
2.1
PHYSICAL FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
SCREEN GRAPHICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
STANDARD KEYBOARD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
TRACKBALL MOUSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
KEY DESCRIPTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
TRACKING SENSITIVITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
CUSTOM KEYBOARD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
KEY DESCRIPTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
2.2
2.3
2.4
3
CONSOLE SETUP
3.1
3.2
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
SETUP CONSOLE CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
TITLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
SETUP TIMERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
UID MNEMONICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
STATUS MNEMONICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
SETUP SITE, HOME, AND GROUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
SETUP CALL BLOCKS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
PATCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
ALL CALL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
SCREEN SAVER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
UID HOLD/TRANSFER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
LISTEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
ALL MUTE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
SINGLE MUTE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
ALARM INDICATOR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
RELAY CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
INTERROGATE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
LOAD FILE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
SAVE/DELETE FILE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
COLOR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
INCOMING UID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
INCOMING TELCO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
EMERGENCY QUEUE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
UNIQUE ID DIRECTORY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
DTMF DIRECTORY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
BLOCK DIRECTORY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
GROUP DIRECTORY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
TONES DIRECTORY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
TELCO DIRECTORY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
BLOCKED / LIMITED / UNLIMITED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
3.3
1
TABLE OF CONTENTS (CONT.)
3.4
SETUP FUNCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-5
CONSOLE VERSION NUMBER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
SELECT FILES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
UNIQUE ID MNEMONICS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
SYSTEM FEATURES LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
SELECT INCOMING CALLS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
SETUP INPUT/OUTPUT CONTACTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
STATUS MNEMONICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11
SET AMUTE TIME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11
SET HOLD TIME. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11
TITLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12
DTMF LEVEL SET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12
3.5
BLOCK LOAD FUNCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-12
BLOCK LOAD SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12
3.6
GROUP DIRECTORY FUNCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-13
GROUP DIRECTORY SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13
3.7
UNIQUE ID DIRECTORY FUNCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-14
UNIQUE ID DIRECTORY SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15
3.8
DTMF DIRECTORY FUNCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-16
DTMF DIRECTORY SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16
3.9
PATCH FUNCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-16
PATCH SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-17
VIEW/DELETE PATCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-17
ADD TO A PATCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-18
3.10 TONES FUNCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-18
SETUP TONES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-18
3.11 COLOR CHANGES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-19
4
ENCRYPTION
4.1
4.2
4.3
MODIFYING EXISTING FILES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1
BLOCK DIRECTORY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1
UNIQUE ID DIRECTORY SETUP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1
5
911 INTERFACE
5.1
5.2
5.3
5.4
MICROPHONE INPUTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1
MICROPHONE OUTPUTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1
OPERATOR AND SUPERVISOR EAR OUTPUTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1
CIRCUIT DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1
GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
INPUTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
HEADSETS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
TELEPHONE/HEADSET INTERFACE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
CONTROL INPUTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
OUTPUTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
MECHANICAL ASSEMBLIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
THEORY OF OPERATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
6
911 INTERFACE MODULE INSTALLATION AND SETUP
6.1
6.2
6.3
6.4
CONSOLE HARDWARE CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-1
911 INTERFACE MODULE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-1
911 JACK BOX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-1
CONSOLE AUDIO PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-2
2
TABLE OF CONTENTS (CONT.)
6.5
6.6
6.7
6.8
6.9
7
IDC AUDIO INTERFACE CARD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
JUMPER DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
JUMPER USAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3
SWITCH SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3
PCM SUMMATION CARD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
I/O ALARM RELAY CARD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
ALARMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
OUTPUTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
RELAY INPUTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
RELAY OUTPUTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5
CONNECTOR PIN ASSIGNMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5
IDM PRE-ALIGNMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7
RECEIVE AUDIO ALIGNMENT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7
TRANSMIT AUDIO ALIGNMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7
911 INTERFACE ALIGNMENT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8
911 TUNING PROCEDURE/GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8
HEADSET MICROPHONE INPUT/ CONSOLE MICROPHONE OUTPUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8
DESK MICROPHONE ADJUSTMENTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9
SUPERVISOR MICROPHONE ADJUSTMENTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9
PAGING AUDIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9
HEADSETS RECEIVE AND CONSOLE AUDIO. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9
911 RECEIVE AUDIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-10
911 TRANSMIT AUDIO AND 911 RECORDER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-10
OPTIONAL INPUT/OUTPUT ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11
PARTS LIST
IDC AUDIO CONTROL CARD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
SPEAKER CONSOLE PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4
PCM SUMMATION BOARD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4
911 INTERFACE MODULE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5
JACK BOX. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-10
8
SCHEMATICS AND COMPONENT LAYOUTS
8-1
8-2
8-3
8-4
8-5
8-6
8-7
8-8
8-9
8-10
8-11
8-12
8-13
8-14
8-15
8-16
8-17
911 INTERFACE MODULE CONSOLE INTERCONNECT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2
DESK MICROPHONE SCHEMATIC AND BOARD LAYOUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3
CONSOLE AUDIO PANEL COMPONENT LAYOUT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-4
CONSOLE AUDIO PANEL SCHEMATIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-4
IDC COMPONENT LAYOUT (COMP SIDE VIEW) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5
IDC COMPONENT LAYOUT (OPP COMP SIDE VIEW) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5
IDC SCHEMATIC (1 OF 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-6
IDC SCHEMATIC (2 OF 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7
PCM SUMMATION BOARD COMPONENT LAYOUT (COMP SIDE VIEW) . . . . . . . . . . . . . . . . . . . . . . . . . 8-8
PCM SUMMATION BOARD COMPONENT LAYOUT (OPP COMP SIDE VIEW) . . . . . . . . . . . . . . . . . . . . . 8-8
PCM SUMMATION SCHEMATIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9
911 INTERFACE COMPONENT LAYOUT (COMP SIDE VIEW) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10
911 INTERFACE COMPONENT LAYOUT (OPP COMP SIDE VIEW) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-11
911 INTERFACE SCHEMATIC (1 OF 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-12
911 INTERFACE SCHEMATIC (2 OF 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-13
911 INTERFACE JACK BOX WIRING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-14
911 INTERFACE JACK BOX SCHEMATIC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-14
A
CUSTOM TO STANDARD KEYBOARD CROSS REFERENCE
3
TABLE OF CONTENTS (CONT.)
LIST OF FIGURES
1-1
2-1
2-2
2-3
3-1
3-2
3-3
3-4
3-5
3-6
3-7
3-8
3-9
3-10
3-11
3-12
3-13
3-14
3-15
3-16
3-17
3-18
3-19
3-20
3-21
3-22
3-23
3-24
3-25
3-26
3-27
3-28
3-29
3-30
3-31
3-32
3-33
3-34
3-35
4-1
4-2
5-1
6-1
6-2
6-3
6-4
6-5
6-6
6-7
6-8
6-9
BASIC CONSOLE SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
MULTI-NET CONSOLE SCREEN LAYOUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
TRACKBALL MOUSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
CUSTOM KEYBOARD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
SETUP FUNCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
MULTI-NET SYSTEM BLOCK DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
SELECT FILES FLOWCHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
FILE NAME POPUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
PASSWORD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
NEW PASSWORD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
VERIFY NEW PASSWORD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
FILE NAME POPUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
FILE NAME MENU. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
SITE POPUP WINDOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
SITE SELECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
HOME SELECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
SITE AND HOME POPUP WINDOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
GROUP SELECTION POPUP WINDOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
SETUP I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
ALARM SETUP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
RELAY SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
MNEMONICS SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11
STATUS MNEMONICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11
MUTE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11
HOLD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11
BLOCK LOAD FUNCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12
FILE NAME POPUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13
GROUP DIRECTORY FUNCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14
FILE NAME MENU. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14
UNIQUE ID DIRECTORY FUNCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15
FILE NAME POPUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15
FILE NAME MENU. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15
SETUP PATCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-17
SETUP PATCH WINDOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-17
PATCH INSTRUCTIONAL WINDOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-17
CALL BLOCK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-17
VIEW/DELETE PATCH WINDOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-17
ADD TO PATCH WINDOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-18
TONES POPUP WINDOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-18
BLOCK DIRECTORY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
ENCRYPTION TITLE BLOCK. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
911 INTERFACE BLOCK DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
CONSOLE BLOCK DIAGRAM WITH 911 INTERFACE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
AUDIO CARD S1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3
AUDIO CARD S2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3
S1 350 HEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
RELAY BLOCK DIAGRAM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6
DCC CONSOLE AUDIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7
S5 TEST 1 SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7
S5 TEST 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7
IDM S5 TEST 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-10
4
TABLE OF CONTENTS (CONT.)
6-10
6-11
6-12
IDC ALIGNMENT POINTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-12
PCM SUMMATION ALIGNMENT POINTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-12
911 INTERFACE ALIGNMENT POINTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-13
LIST OF TABLES
3-1
3-2
3-3
5-1
5-2
5-3
6-1
6-2
6-3
6-4
6-5
FEATURES LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
TONE NUMBERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-18
KEYBOARD FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-19
JUMPER PROGRAMMING FOR INPUT BLOCKS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
JUMPER PROGRAMMING FOR OUTPUT BLOCKS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
JUMPER PROGRAMMING FOR LOGIC BLOCKS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
CONSOLE HARDWARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
INTERFACE CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
LINE ITEMS/ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
ALARM RELAY OUTPUTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
CONNECTOR PINOUTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5
5
TABLE OF CONTENTS (CONT.)
6
INTRODUCTION
SECTION 1 INTRODUCTION
1.1 SCOPE OF THIS MANUAL
An output is also provided for connection to a
recorder.
The scope of this manual is to describe the setup
and selection of features in the E.F. Johnson Console
for the Multi-Net system. It is intended as a guide for
the screens and provides definitions of the functions.
Use the Table of Contents and Index to locate specific
information. Use this manual to become familiar with
the console’s operation before using the console, and
then as a reference for functions.
1.4 911 INTERFACE MODULE
The 911 Interface Module contains the jumpers
that selects the operator’s headset, supervisor’s headset
or desk microphone. The selected audio is then routed
to the computer. The computer, foot pedal PTT, desk
microphone, headsets and interconnect to the RNT are
all connected to the interface module.
1.2 MULTI-NET CONSOLE
1.5 UNSELECT AUDIO PERSONALITY CARD
The Multi-Net Console is based on a computer
driven CRT system consisting of a 386 based computer with 4 MB of RAM, hard disk drive, 3.25"
floppy disk drive, VGA CRT, 2 serial ports and a 101
AT style keyboard (See Section 2.2). The computer
must be equipped with a trackball mouse (see Section
2.2) and custom keyboard (see Section 2.4). The computer uses the extended memory via a software memory manager.
The Multi-Net Console connects to a single Intelligent Dispatch Module (IDM) in the RNT at 9600
baud. There is an unselect audio personality card on
the IDM if the console is optioned to have unselect
audio.
1.6 CONSOLE MANAGER
1.3 AUDIO INTERFACE
The Console Manager is the person responsible
for the setup and maintenance of Call Blocks, Directories, etc. in all the consoles. Therefore, this manual is
structured for the Manager.
Audio is connected to the console through an
expansion slot in the computer. This connection provides the audio volume control for the speaker, headset and unselect audio speaker. This connection also
controls the alert tones to be transmitted to the
mobiles.
1.7 CONSOLE USER
The Console User is the person using the console,
i.e. Dispatcher. Refer to the Console Operator’s Manual, Part No. 002-3039-272.
Two inputs to this connection provide the transmit audio function for the transmitter, the desk microphone or a headset microphone.
1-1
September 1995
Part No. 004-3039-272
INTRODUCTION
Figure 1-1 BASIC CONSOLE SETUP
September 1995
Part No. 004-3039-272
1-2
INTRODUCTION
CONSOLE SPECIFICATIONS
Audio Output
Audio Input
+7 dBm maximum into 600 ohms
-30 dBm input minimum from 600 ohms
Boom Microphone
Desk Microphone
Headset Input
GN Profile III (-024)
Plantronics series (-030/-032)
-80 dBm input
-40 dBm input
Line Balance
Distortion
66 dB at 1 kHz
< 3% at full output levels
Frequency Response
-3 to +1 dB from 300 to 3 kHz
Speaker Output
5 watts
Mute Level
> 50 dB from full output
RS-232 Interface
Tx/Rx with ground, 4-wire MODEM option
Recorder Output
600 ohm balanced or 300 ohm unbalanced
Diagnostics
Displayed on CRT and at the System Management Module
Capacity
1 position per Intelligent Dispatch Module. Number of positions
essentially unlimited (Contact E.E. Johnson Systems Marketing).
-57 dBm input
-22 dBm input
Power Input
Computer
CRT
Dimensions
Computer
CRT
Keyboard
Mouse
911 Interface Module
911 Jackbox
Speaker Panel
Custom Keyboard
Environment
Telco Input
115V AC 6A or 230V AC 4A 50/60 Hz
120/240V AC 90 Watts 50/60 Hz
Height
Width
Depth
18.0"
14.00"
6.50"
18.0"
14.00"
14.50"
8.0"
19.00"
2.75"
4.5"
5.00"
1.50"
2.0"
19.00"
5.25"
1.5"
7.25"
4.50"
4.5"
19.00"
5.25"
5.5"
16.00"
2.00"
10°C to 50°C with 10% to 90% noncondensing humidity
0 dB maximum, -17 dB minimum (Typically -7 dB)
1-3
September 1995
Part No. 004-3039-272
INTRODUCTION
DIGITAL INPUTS
Number of Inputs
8
Type
Non-polarized, optically isolated from each other and from the
computer (not TTL/CMOS compatible).
Voltage Range
5 to 24V DC or AC (50 to 1 kHz)
Isolation
500V channel-to-ground or channel-to channel
Input Resistance
470 ohms in series with two diodes and an LED
Response Time
10 ms w/filter, 20 µs w/o filter
RELAY OUTPUTS
Number of outputs
8
Contact Rating
2A carry current, bifurcated, gold clad, silver palladium
Contact Arrangement
Channels 0-4 are SPDT Form C
Channels 5-7 are SPST Form A
Contact Resistance
Initial 100 milliohms maximum
Contact Life
Mechanical 100 million operations minimum
Electrical
5 million operations minimum at full load
Operating Time
5 milliseconds maximum
POWER REQUIRED
+5V DC at 0.5A (all relays ON)
ENVIRONMENTAL
Ambient Temperature
Operating 0° to +50° C
Storage -20° to +70° C
Humidity
0 to 90% (non-condensing)
Weight
Approximately 8 ounces
September 1995
Part No. 004-3039-272
1-4
CONSOLE SCREEN LAYOUT
SECTION 2 CONSOLE SCREEN LAYOUT
2.1 PHYSICAL FEATURES
given a Unique ID when receiving (or the Unique
ID number if a name is not assigned) and the
Unique ID’s status and Priority.
The Console utilizes a window style of operation.
Refer to Figure 2-1 for an example of the screen presentation and Sections 2.2 and 2.4 for example of the
keyboards.
3. The Console title, month, day, year and time in
hours:minutes:seconds (and hours:minutes in large
numbers) are in the upper left corner. Refer to Figure 2-1.
2.1.1 SCREEN GRAPHICS
4. There are 2 sets of 15 function icons displayed
along the lower left. The name of the function is
displayed in the key.
1. The blue logo in the upper left corner of the console
screen is a transmit indicator. The logo changes to
white when the PTT is pressed and the call is in
queue while the logo remains white. The logo
changes to red when system access is gained and the
transmitter has actually been keyed.
5. The area on the lower right is a scroll area. Information concerning calls are displayed in this window as calls are received.
2. There are 16 Call Blocks displayed on the upper
right side. Each call block displays the title identifying the block. The block also shows the name
6. Active alarm and relay indicators are displayed in a
vertical area to the left of the call blocks.
Figure 2-1 MULTI-NET CONSOLE SCREEN LAYOUT
2-1
September 1995
Part No. 004-3039-272
CONSOLE SCREEN LAYOUT
2.2 STANDARD KEYBOARD
With the custom keypad, the keys are designated
to select icons without having to place the cursor on
the screen icon and press the Enter key. Pressing the
TOG M icon key enables the function in the lower half
of the key, and pressing the TOG M icon key again
toggles the icon keys to the functions at the top portion
of the icon key.
The standard keyboard is used for Disk Operating
System (DOS) operations only. See Appendix A for a
cross reference to custom keyboard keys.
2.3 TRACKBALL MOUSE
The arrow keys are used to move the cursor
around the screen to the various menu selections. The
alphabet keyboard is used to enter names of Call
Blocks, etc. and the keypad at the right is used to
select Call Blocks. The numerical keypad in the center is used to enter numbers and DTMF digits.
The console can be equipped with a trackball
style mouse. When the mouse is used the trackball
moves the cursor to selections in the same manner as
the arrow keys.
2.3.1 KEY DESCRIPTIONS
2.4.1 KEY DESCRIPTIONS
As shown in Figure 2-2 the left mouse key is used
as the Enter key, the middle key as the PTT key and
the right key as the Escape key. When making data
entries such as Site Selection etc., the keyboard Enter,
Escape and arrow keys must be used to accept entries,
exit the menus and move the cursor, the mouse keys
have no effect during the data entry operation.
1. Alphabetical Key Section
These keys are used to enter filenames, call block
titles, etc. by the console manager.
2. Numeric Key Section
2.3.2 TRACKING SENSITIVITY
These keys are used to enter numbers and to send
DTMF tones.
Set the sensitivity of the mouse by pressing the
CNTL, ALT and mouse middle key at the same time.
A popup window appears and the ballistics can be
adjusted for the sensitivity of the trackball (Normal
settings are: ballistics=high, sensitivity=2).
3. Function Icon Key Section
The keys are designated to select function icons
without having to place the cursor on the screen icon
and press the Enter key.
Pressing the TOG M icon key enables the function in the lower half of the key, and pressing the TOG
M icon key again toggles the function icon keys to the
functions at the top portion of the icon keys.
The arrow keys are used to move the cursor
around the screen to the various menu selections.
4. Call Block Key Section
The keypad at the right is used to select Call
Blocks.
Figure 2-2 TRACKBALL MOUSE
2.4 CUSTOM KEYBOARD
September 1995
Part No. 004-3039-272
2-2
CONSOLE SCREEN LAYOUT
Figure 2-3 CUSTOM KEYBOARD
2-3
September 1995
Part No. 004-3039-272
CONSOLE SCREEN LAYOUT
September 1995
Part No. 004-3039-272
2-4
CONSOLE SETUP
SECTION 3 CONSOLE SETUP
3.1 INTRODUCTION
The SETUP function allows the setup of Site,
Homes and Groups each console is allowed to use
(See Figure 3-2). Call Blocks, Group Directories and
Unique ID Directories can be selected from this menu
by their 8 character names. This function also permits
the customization of the title (See Section 3.4).
NOTE: The descriptions for setup are given for the
custom keyboard. Refer to Section 2.2 for use of the
computer keyboard and trackball mouse.
Different functions and directories must be configured before the console will operate correctly.
Some of these features may not pertain to your console, therefore those steps will be skipped.
This page intentionally left blank.
Figure 3-1 SETUP FUNCTION
September 1995
Part No. 004-3039-272
3-1
CONSOLE SETUP
This page intentionally left blank.
Figure 3-2 MULTI-NET SYSTEM BLOCK DIAGRAM
September 1995
Part No. 004-3039-272
3-2
CONSOLE SETUP
3.2 SETUP CONSOLE CONFIGURATION
3.2.8 ALL CALL
This setup configures functions and directories to
allow the console to operate correctly. Not all of the
possible features listed here may apply to your specific
console. Basic console software (Multi-Net DCC software PN 023-9998-205) is loaded at the factory,
options setup per sales order.
All Call is a feature that can be enabled or disabled (see Section 3.4.4). Refer to Console Operator’s
Manual, Part No. 002-3039-272, for definition and
usage instructions.
3.2.1 TITLE
Screen Saver is a feature that can be enabled or
disabled (see Section 3.4.4).
3.2.9 SCREEN SAVER
Refer to Section 3.4.10 for changing the console’s
title.
3.2.10 UID HOLD/TRANSFER
3.2.2 SETUP TIMERS
UID Hold/Transfer is a feature that can be
enabled or disabled (see Section 3.4.4). Transfer is
only used to connect Telco to UID or UID to Telco
calls. Refer to Console Operator’s Manual, Part No.
002-3039-272 for definition and usage
instructions.
Refer to Section 3.4.8 for setting the AMUTE
Time and Section 3.4.9 for setting the Hold Time.
3.2.3 UID MNEMONICS
3.2.11 LISTEN
Refer to Section 3.4.3 for defining each UID.
3.2.4 STATUS MNEMONICS
Listen is a function that allows the console operator to monitor the communication between another
console and a mobile unit. Listen is a feature that can
be enabled or disabled (see Section 3.4.4). Refer to
Console Operator’s Manual, Part No. 002-3039-272,
for definition and usage instructions.
Refer to Section 3.4.7 for defining each Status.
3.2.5 SETUP SITE, HOME, AND GROUP
3.2.12 ALL MUTE
The Sites, Home Channels and Groups to be used
by the Console need to be enabled. These same Sites,
Homes and Groups must be defined in the associated
RNT. Refer to Section 3.4.5 for defining the Sites,
Home Channels and enabling the associated Talk
Groups.
All Mute is a feature that can be enabled or disabled (see Section 3.4.4). Refer to Console Operator’s
Manual, Part No. 002-3039-272, for definition and
usage instructions.
3.2.13 SINGLE MUTE
3.2.6 SETUP CALL BLOCKS
Single Mute is a feature that can be enabled or
disabled (see Section 3.4.4). Refer to Console Operator’s Manual, Part No. 002-3039-272, for definition
and usage instructions.
Each Call Block used on the Console must be
defined and should be saved to a file. Refer to Section
3.5 for defining the Call Block parameters.
3.2.14 ALARM INDICATOR
3.2.7 PATCH
The Alarm indicators can be redefined and this
feature can be enabled or disabled (see Section 3.4.4).
Refer to Section 3.4.6 for definition and setup of the
Alarm inputs.
Patch is a feature that can be enabled or disabled
(see Section 3.4.4). If this feature is enabled refer to
Section 3.9 to create a Patch.
3-3
September 1995
Part No. 004-3039-272
CONSOLE SETUP
3.2.15 RELAY CONTROL
3.2.23 UNIQUE ID DIRECTORY
The Relays can be defined to function normally
open or normally closed. The redefining of the relays
feature can be enabled or disabled (see Section 3.4.4).
Refer to Section 3.4.6 for definition and setup of the
Relay outputs.
The Unique ID Directory consists of files of
defined Unique IDs. This directory can be defined as
Blocked, Limited or Unlimited (see Section 3.3).
Refer to Section 3.7 for definition and setup instructions.
3.2.16 INTERROGATE
3.2.24 DTMF DIRECTORY
Interrogate is a feature that can be enabled or disabled (see Section 3.4.4). Refer to Console Operator’s
Manual, Part No. 002-3039-272, for definition and
usage instructions.
The DTMF Directory consists of files of defined
DTMF tones. This directory can be defined as
Blocked, Limited or Unlimited (see Section 3.3). The
DTMF tones are transmitted to the mobiles only.
Refer to Section 3.8 for definition and setup instructions.
3.2.17 LOAD FILE
The loading of a file from any of the directories
(Unique ID, DTMF, Block, Group, Tones and Telco)
can be enabled or disabled (see Section 3.4.4).
3.2.25 BLOCK DIRECTORY
3.2.18 SAVE/DELETE FILE
The Block Directory consists of files of defined
Call Blocks. This directory can be defined as
Blocked, Limited or Unlimited (see Section 3.3).
Refer to Section 3.5 for definition and setup instructions.
The saving of a new file or deleting of an existing
file in a directory (Unique ID, DTMF, Block, Group,
Tones and Telco) can be enabled or disabled (see Section 3.4.4).
3.2.26 GROUP DIRECTORY
3.2.19 COLOR
The Group Directory consists of files of defined
Talk Groups. This directory can be defined as
Blocked, Limited or Unlimited (see Section 3.3).
Refer to Section 3.6 for definition and setup instructions.
The Colors of the console display may be
changed and is a feature that can be enabled or disabled (see Section 3.4.4). Refer to Section 3.11 for
definition and setup instructions.
3.2.20 INCOMING UID
3.2.27 TONES DIRECTORY
Incoming Unique ID calls is a feature that can be
enabled or disabled (see Section 3.4.4).
The Tones Directory consists of files of defined
Tones. This directory can be defined as Blocked,
Limited or Unlimited (see Section 3.3). Refer to Section 3.10 for definition and setup instructions.
3.2.21 INCOMING TELCO
Incoming Telco calls is a feature that can be
enabled or disabled (see Section 3.4.4).
3.2.28 TELCO DIRECTORY
3.2.22 EMERGENCY QUEUE
The Telco Directory consists of files of defined
Telephone numbers. This directory can be defined as
Blocked, Limited or Unlimited (see Section 3.3).
Refer to Section 3.6 for definition and setup instructions.
Emergency Queue is a feature that can be enabled
or disabled (see Section 3.4.4). Refer to Console
Operator’s Manual, Part No. 002-3039-272 for definition and usage instructions.
September 1995
Part No. 004-3039-272
3-4
CONSOLE SETUP
3.3 BLOCKED / LIMITED / UNLIMITED
3.4.2 SELECT FILES
The use of the Directory functions can be configured or defined to be Blocked, Limited or Unlimited.
If the directory is to be defined as Blocked nothing
more needs to be defined. If Limited, each directory
must be completely defined under Unlimited before
being defined as Limited.
The select files command allows loading all files
saved under the same file name. These files include:
Group Directory, Unique ID Directory, Call Block,
Site, Home and Group.
NOTE: If the same file name is used to Save Files in
all setup functions (Site, Home, Group, GRP D, UID
D, BLK LD), when the Select Files icon key is pressed
all setup functions with the same file name are loaded
(see Figure 3-3).
Unlimited: Anything can be changed in the use of
this function by the Console Operator. An example is
in TELCO; any of the 32 possible TELCO names and
numbers assigned can be changed.
Limited: Use of this function is limited to the
Console Operator. An example is in TELCO; only the
first line of the 32 possible TELCO names and numbers can be changed. When the popup window
appears, an "L" is displayed in the border on the upper
right if the function has been defined as Limited. In
this mode the first line should be reserved as a scratch
pad line to handle any changes.
Blocked: This function has been disabled to the
Console Operator. When a function is selected that
has been Blocked, a popup window appears stating
"This feature is BLOCKED. NO access is permitted".
3.4 SETUP FUNCTION
Select the SETUP icon key. If the SETUP icon is
not present on the screen, press the TOG M key and
then select the SETUP key.
NOTE: The descriptions for setup are given for the
custom keyboard. Refer to Section 2.2 for use of the
computer keyboard and trackball mouse.
3.4.1 CONSOLE VERSION NUMBER
Figure 3-3 SELECT FILES FLOWCHART
1. Press the SETUP icon key.
1. Press the SETUP icon key.
2. Move the cursor bar to highlight Console Version
Number and press Enter.
2. Move the cursor bar to highlight SELECT FILES
and press Enter.
3. The Version popup window appears with the Revision number.
3. The File Name popup window appears.
4. Press any key to clear popup window.
4. Highlight the file name to load and press Enter.
3-5
September 1995
Part No. 004-3039-272
CONSOLE SETUP
Features 18 through 23 can be toggled between
three modes; Blocked, Limited or Unlimited. When a
feature is in Blocked Mode it is disabled. Limited
Mode allows the Console Operator to change only the
first entry of the directory. Unlimited Mode allows the
Console Operator to change all or any part of an entry
of the directory.
Table 3-1 FEATURES LIST
Figure 3-4 FILE NAME POPUP
3.4.3 UNIQUE ID MNEMONICS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
This allows an alphanumeric mnemonic to be
associated with each of the 8163 different Unique IDs.
1. Press the SETUP icon key.
2. Move the cursor bar to highlight UID MNEMONICS and press Enter. The UID Mnemonic popup
window appears.
3. Enter in the desired UID to be labeled and press
Enter.
4. The cursor automatically moves to the Mnemonics
entry point.
5. Enter in the Mnemonic and press Enter.
6. The popup window automatically increments to the
next UID and label this UID.
FEATURE
Patch
All Call
Screen Saver
UID Hold/Transfer
Last Received Queue
Listen
All Mute
Single Mute
Alarm Indicator
Relay Control
Interrogate
Load File
Save File
Color
Incoming UID
Incoming Telco
Emergency Queue
UID Directory
DTMF Directory
Block Directory
Group Directory
Tones Directory
Telco Directory
7. Repeat Steps 4 and 5 for consecutive UIDs.
1. Press the SETUP icon key.
8. Use the arrow keys to move to another UID or if
large gap in UIDs occurs repeat starting at Step 3.
2. Move the cursor bar to highlight SYSTEM FEATURE LIST and press Enter. The System Feature
List popup window appears.
3.4.4 SYSTEM FEATURES LIST
3. Move the cursor bar to highlight FEATURE LIST
and press Enter. The Enter Password popup window
appears.
The Consoles are purchased with some or all of
the possible options offered. These options have been
separated into 23 features (see Table 3-1). Each feature can be password protected once it is defined and
configured. It is highly recommended the password
function be used to safe guard against any inadvertent
changes during the operation of the Console. The Features function allows Features 1 through 17 to be disabled or enabled.
Figure 3-5 PASSWORD
September 1995
Part No. 004-3039-272
3-6
CONSOLE SETUP
File Selection
4. Type in the password or if a previous password has
not been stored press the Enter key. The Feature
List popup window appears.
1. To SAVE this file with File Selection highlighted
from the file menu press the ENTER key and the
Load/Save File popup window appears.
5. Move the cursor to scroll through and highlight the
desired feature to change. Pressing the Enter key
toggles the feature between Enabled/Disabled or
Blocked/Limited/Unlimited.
2. Move the cursor to highlight SAVE TO NEW FILE
and press Enter. The File Name popup window
appears (see Figure 3-8).
6. Repeat this for each feature to be changed.
7. Press the ESC key to exit and return to the System
Feature List popup window. The entries are automatically saved when exiting.
Figure 3-8 FILE NAME POPUP
3.4.5 SELECT INCOMING CALLS
3. Type in the name of the file and press Enter. The file
is saved and automatically exits to the Incoming
Call popup window.
1. To enter in a password or a new password, move the
cursor to highlight NEW PASSWORD and press
Enter. The New Password popup window appears if
a password does not exist (see Step 12).
4. To ADD to an existing file press the LOAD/ SAVE
FILE key and the Load/Save File popup window
appears.
5. Move the cursor to highlight SAVE TO DIRECTORY FILE and press Enter. The Directory File
popup window appears (see Figure 3-9).
Figure 3-6 NEW PASSWORD
6. Move the cursor to highlight the desired file and
press Enter. The file is saved and automatically
exits to the Incoming Call popup window.
2. Type in the new password and press Enter. Verify
New Password popup window appears.
7. To LOAD an existing file press the LOAD/ SAVE
FILE key and the Load/Save File popup window
appears.
Figure 3-7 VERIFY NEW PASSWORD
8. Move the cursor to highlight LOAD FILE and press
Enter. The Directory File popup window appears
(see Figure 3-9).
3. Type in the new password and press Enter. This
confirms the new password and exits back to the
System Feature List popup window.
9. Move the cursor to highlight the desired file and
press Enter. The file is loaded and automatically
exits to the Incoming Call popup window.
4. Press the ESC key to exit the System Feature List
popup window.
10.To DELETE an existing file press the LOAD/
SAVE FILE key and the Load/Save File popup window appears.
5. If a password already exists, the Enter Old Password
popup window would have appeared. Type in the
old password and press Enter. Now the New Password popup window appears and you can continue
at Step 9.
11. Move the cursor to highlight DELETE FILE and
press Enter. The Directory File popup window
appears (see Figure 3-9).
3-7
September 1995
Part No. 004-3039-272
CONSOLE SETUP
Home Selection, enables or disables the Home numbers assigned to a given site. Refer to Figure 3-1 for the
Setup screen. The Popup screens in Figures 3-10 and
3-12 appear when Home Selection is selected in the
setup menu. (See Save Selection Files.)
12.Move the cursor to highlight the desired file and
press Enter. The file is deleted and automatically
exits to the Incoming Call popup window.
13.To EXIT the Incoming Call popup window press
the Escape (ESC) key.
1. Press the SETUP icon key.
2. Move the cursor bar to highlight Select Incoming
Calls and press Enter.
3. Move the cursor bar to highlight Home Selection
and press Enter.
Figure 3-9 FILE NAME MENU
4. The Enter Site popup window appears (see Figure
3-10).
Site Selection, enables all the sites in which the
Home and Group of the mobiles to establish calls with
are located. Refer to Figure 3-1 for the Setup screen.
The popup screen in Figure 3-11 is selected in the setup
menu. (See Save Selection Files.)
1. Press the SETUP icon key.
Figure 3-10 SITE POPUP WINDOW
2. Move the cursor bar to highlight Select Incoming
Calls and press Enter.
5. Type the site number (1 to 255) where the Home is
located and press Enter. (An invalid number displays an error message).
3. Move the cursor bar to highlight Site Selection and
press Enter.
6. The Home popup window appears (see Figure 312).
4. The Site popup window appears with sites that are
enabled or disabled.
7. Move the cursor using the arrow keys to highlight
the Home number to Enable or Disable. The Home
number in the popup window changes to indicate
the selected number.
5. Move the cursor with the arrow keys to an empty
box.
6. Type the number of the site to enable and press
Enter. (There are 255 sites available.)
8. When the Home number is selected, press Enter to
toggle the Enable or Disable of this Home.
7. When all site entries have been made, press escape
(ESC).
September 1995
Part No. 004-3039-272
9. Press Escape (ESC) to exit.
3-8
CONSOLE SETUP
Figure 3-11 SITE SELECTION
4. The Enter Site popup window appears.
Figure 3-13 SITE AND HOME POPUP WINDOW
5. Type Site number (1 to 255) and press Enter.
6. The Home popup window appears.
Figure 3-12 HOME SELECTION
7. Type Home number (1-30) and press Enter. (An
invalid number displays an error message.)
Group Selection, enables or disables Groups for a
given Site and Home. Refer to Figure 3-1 for the
Setup screen. The Popup screens in Figures 3-13 and
3-14 appear when Site is entered in the setup menu.
(See Save Selection Files.)
8. The popup window shows all 256 Groups.
NOTE: Groups 1-225 are available Groups. 226 to
256 are reserved by the system and normally disabled.
1. Press the SETUP icon key.
2. Move the cursor bar to highlight Select Incoming
Calls and press Enter.
9. Move the cursor using the arrow keys to the position
of the Group number.
3. Move the cursor bar to highlight Group Selection
and press Enter.
10.Press Enter to toggle between Enable/Disable.
3-9
September 1995
Part No. 004-3039-272
CONSOLE SETUP
11. Press Escape (ESC) to exit.
Figure 3-15 SETUP I/O
Input Setup
1. Press the SETUP icon key.
2. Move the cursor bar to highlight SETUP I/O and
press Enter. The Setup I/O popup window appears
(see Figure 3-15).
3. Move the cursor bar to highlight Alarm Setup and
press Enter. The Alarm Setup popup window
appears (see Figure 3-16).
Figure 3-14 GROUP SELECTION POPUP
WINDOW
3.4.6 SETUP INPUT/OUTPUT CONTACTS
The Input contacts are for warning or alarm indications. There are three modes of indication for the
eight possible alarms: Non-Alarm, Alarm and Alarm
with Tone. Each alarm can be defined with a mnemonic label at the time the alarm is setup. Refer to
Figure 3-1 for the Setup screen.
Mode
Alarm
Alarm w/Tone
Non-Alarm
Figure 3-16 ALARM SETUP
4. Move the cursor bar to highlight the desired alarm to
change. Pressing the Enter key toggles between the
three different modes: Non-Alarm, Alarm, and
Alarm with Tone.
Indication
Visual Only
Visual and Audible
Monitoring Visual
5. Press the ESC key to exit and return to the Setup I/
O popup window. The entries are automatically
saved when exiting.
The Output contacts are the opening and closing
of a relay. There are two modes of closing the 8 available relays: Toggle or Non-Toggle. Each alarm can be
defined with a mnemonic label at the time the alarm is
setup. Refer to Figure 3-1 for the Setup screen.
Output Setup
1. Move the cursor bar to highlight Relay Setup and
press Enter. The Relay Setup popup window
appears (see Figure 3-17).
In the Toggle Mode, once the associated keys are
pressed the relay closes and remains closed until the
associated keys are pressed again.
In the Non-Toggle Mode, once the associated
keys are pressed the relay closes and remains closed as
long as the keys are pressed.
Figure 3-17 RELAY SETUP
September 1995
Part No. 004-3039-272
3-10
CONSOLE SETUP
2. Move the cursor bar to highlight the desired relay to
change. Pressing the Enter key toggles between the
two different modes.
3. Press the ESC key to exit and return to the Setup I/
O popup window. The entries are automatically
saved when exiting.
Figure 3-19 STATUS MNEMONICS
Mnemonics Setup
3.4.8 SET AMUTE TIME
1. Move the cursor bar to highlight Mnemonic’s Setup
and press Enter. The Mnemonic’s Setup popup window appears (see Figure 3-18).
This sets the All Mute function time-out.
1. Press the SETUP icon key.
2. Move the cursor bar to highlight Set AMUTE Time
and press Enter.
3. A popup window appears requesting up to two digits of time-out. The time is from 0 to 99 seconds.
Press Enter, the window disappears.
Figure 3-18 MNEMONICS SETUP
2. Move the cursor bar to highlight the desired alarm or
relay to define. Type in the desired title.
3. Press the ESC key to exit and return to the Setup I/
O popup window. The entries are automatically
saved when exiting.
Figure 3-20 MUTE
3.4.9 SET HOLD TIME
4. Press the ESC key to exit the Setup I/O popup window.
This sets the time for the Hold function.
3.4.7 STATUS MNEMONICS
1. Press the SETUP icon key.
This allows an alphanumeric mnemonic to be
associated with the status codes received from the field
units. Refer to the mobile control head programming
for Status Mnemonics.
2. Move the cursor bar to highlight Set Hold Time and
press Enter.
3. A popup window appears requesting up to three digits of hold time (0 to 255 seconds).
1. Press the SETUP icon key.
2. Move the cursor bar to highlight STATUS MNEMONICS and press Enter. The Status popup window appears.
Figure 3-21 HOLD
3. Move the cursor to the status number and type the
mnemonic (8 characters) in the window.
4. Press Enter, the window disappears. If invalid numbers are entered an error window appears.
4. Press ESC to exit and save the entries.
3-11
September 1995
Part No. 004-3039-272
CONSOLE SETUP
3.4.10 TITLE
3.5.1 BLOCK LOAD SETUP
This allows the console title at the upper left of
the screen to be modified (see Figure 3-1).
NOTE: If the BLKLD icon is not present on the screen,
press the TOG M icon key.
1. Press the SETUP icon key.
1. Press the BLK LD icon key. The Popup screen in
Figure 3-22 appears.
2. Move the cursor bar to highlight Title and press
Enter. The title box is highlighted.
3. Type the title change in the window. (2 lines of up
to 11 alphanumeric characters each.)
4. Press ESC to exit and save the new Title.
3.4.11 DTMF LEVEL SET
Figure 3-22 BLOCK LOAD FUNCTION
1. Press the SETUP icon key.
2. Move the cursor to highlight the line for the Call
Block. Type the Title for this block or press the right
arrow key if no title is assigned.
2. Move the cursor bar to highlight DTMF Level Set
and press Enter.
3. A DTMF digit is generated to the IDM card for console alignment.
3.5 BLOCK LOAD FUNCTION
3. Using the right arrow key, move the cursor and type
the Site (1-255), Home (1-30), Group (1-256), Priority (1-5), Hang Time (1-255 sec.), Headset Volume Setting (0-96), Select Audio Volume Setting
(0-96) and Unselect Audio Volume Setting (0-96)
for the Call Block.
The Block Load (BLK LD) function is a directory
consisting of files containing definitions of the 16 Call
Blocks. The Block Load function allows the console
manager to set the Title, Site, Home, and Group for
each of the 16 Call Blocks. If a Call Block is not set
up with a valid value for the Site, Home and Group ID,
an error message is displayed.
NOTE: The priority is the transmit priority for the
console transmit. A supervisory console may be established by having the priorities set at least 1 higher
than the priorities on the other consoles. Whenever
the supervisory console transmits it will override other
consoles, even if the other consoles are transmitting on
the same Group.
Once the file is created, the file is saved in the
directory. Each file is created to represent a Call
Block layout for a different call scenario. The only
limit to the number of files in this directory is the
available space on the hard disk.
4. Repeat Sets 2 and 3 until each desired Call Block
has been created.
The console manager is now able to select a file
by scrolling the file names in the directory menu, highlighting the desired file and pressing the Enter key.
This file is automatically loaded and displayed on the
console. To exit the Block Load function, press the
Escape (ESC) key.
5. To SAVE this file press the LOAD/SAVE FILE key
and the Load/Save File popup window appears.
4. Press any key to clear.
September 1995
Part No. 004-3039-272
NOTE: To clear an existing Call Block return all parameters to "0".
6. Move the cursor to highlight SAVE TO NEW FILE
and press Enter. The File Name popup window
appears (see Figure 3-23).
3-12
CONSOLE SETUP
3.6 GROUP DIRECTORY FUNCTION
NOTE: If the GRP D icon is not present on the screen,
press the TOG M icon key.
Figure 3-23 FILE NAME POPUP
The Group Directory (GRP D) function consists
of files that contain the definition of up to 32 Talk
Groups. The Group Directory function allows the
console manager to set the Title, Site, Home, and
Group for each of the Talk Groups. If a Talk Group is
not set up with a valid value for the Site (1-255),
Home (1-30), and Group ID (1-255) an error message
is displayed.
7. Type in the name of the file and press Enter. The file
is saved and automatically exits to the Block Load
popup window.
8. To ADD to an existing file press the LOAD/ SAVE
FILE key and the Load/Save File popup window
appears.
Once the file is created, the file is saved in the
directory. Each file is created to represent the different
Talk Groups for a different configuration. The only
limit to the number of files in this directory is the
available space on the hard disk.
9. Move the cursor to highlight SAVE TO DIRECTORY FILE and press Enter. The Directory File
popup window appears (see Figure 3-25).
10.Move the cursor to highlight the desired file and
press Enter. The file is saved and automatically
exits to the Block Load popup window.
11. To LOAD an existing file press the LOAD/ SAVE
FILE key and the Load/Save File popup window
appears.
The console manager is now able to select a file
by scrolling the file names in the directory menu, highlighting the desired file and pressing the Enter key.
This file is automatically loaded and displayed on the
console. To exit the Group Directory function, press
the Escape (ESC) key.
12.Move the cursor to highlight LOAD FILE and press
Enter. The Directory File popup window appears
(see Figure 3-25).
3.6.1 GROUP DIRECTORY SETUP
1. Press the GRP D icon key. The Group directory is
displayed in a popup window (see Figure 3-24).
13.Move the cursor to highlight the desired file and
press Enter. The file is loaded and automatically
exits to the Block Load popup window.
2. Move the cursor to highlight the line for the entry.
14.To DELETE an existing file press the LOAD/
SAVE FILE key and the Load/Save File popup window appears.
3. Type the name for this Group or press the right
arrow key if no name is assigned.
4. Using the right arrow key to move the cursor, type
the Site (1-255), Home (1-30), Group ID (1-255),
Priority (1-5) and Hang Time (1-255 sec.) for the
Group.
15.Move the cursor to highlight DELETE FILE and
press Enter. The Directory File popup window
appears (see Figure 3-25).
16.Move the cursor to highlight the desired file and
press Enter. The file is deleted and automatically
exits to the Block Load popup window.
5. Repeat Steps 2, 3 and 4 until each desired Group has
been created.
17.To EXIT the Block Load popup window press the
Escape (ESC) key.
NOTE: To clear an existing Call Block return all parameters to "0".
3-13
September 1995
Part No. 004-3039-272
CONSOLE SETUP
16.Move the cursor to highlight DELETE FILE and
press Enter. The Directory File popup window
appears (see Figure 3-25).
17.Move the cursor to highlight the desired file and
press Enter. The file is deleted and automatically
exits to the Group Directory popup window.
18.To EXIT the Group Directory popup window press
the Escape (ESC) key.
Figure 3-24 GROUP DIRECTORY FUNCTION
6. To SAVE this file press the LOAD/SAVE FILE key
and the Load/Save File popup window appears.
7. Move the cursor to highlight SAVE TO NEW FILE
and press Enter. The File Name popup window
appears (see Figure 3-23).
Figure 3-25 FILE NAME MENU
8. Type in the name of the file and press Enter. The file
is saved and automatically exits to the Group Directory popup window.
3.7 UNIQUE ID DIRECTORY FUNCTION
9. To ADD to an existing file press the LOAD/ SAVE
FILE key and the Load/Save File popup window
appears.
NOTE: If the UID D icon is not present on the screen,
press the TOG M icon key.
The Unique ID Directory (UID D) function consists of files that contain the definition of up to 32
Unique IDs. The Unique ID Directory function allows
the console manager to set Name, Unique ID and the
Priority for each of the Unique IDs.
10.Move the cursor to highlight SAVE TO DIRECTORY FILE and press Enter. The Directory File
popup window appears (see Figure 3-25).
11. Move the cursor to highlight the desired file and
press Enter. The file is saved and automatically
exits to the Group Directory popup window.
Once the file is created, the file is saved in the
UID directory. Each file is created to represent the different Unique IDs of different individuals or mobiles.
The only limit to the number of files in this directory is
the available space on the hard disk.
12.To LOAD an existing file press the LOAD/ SAVE
FILE key and the Load/Save File popup window
appears.
The Console Manager is now able to select a file
by scrolling the file names in the directory menu, highlighting the desired file and pressing the Enter key.
This file is automatically loaded and displayed on the
console. To exit the Unique ID Directory function,
press the Escape (ESC) key.
13.Move the cursor to highlight LOAD FILE and press
Enter. The Directory File popup window appears
(see Figure 3-25).
14.Move the cursor to highlight the desired file and
press Enter. The file is loaded and automatically
exits to the Group Directory popup window.
NOTE: A console may call another console via the
Unique ID of the desired console. This provides for a
private intercom function.
15.To DELETE an existing file press the LOAD/
SAVE FILE key and the Load/Save File popup window appears.
September 1995
Part No. 004-3039-272
3-14
CONSOLE SETUP
3.7.1 UNIQUE ID DIRECTORY SETUP
9. To ADD to an existing file press the LOAD/ SAVE
FILE key and the Load/Save File popup window
appears.
1. Press the UID D icon key. The Unique ID directory
is displayed in a popup window (Figure 3-26).
10.Move the cursor to highlight SAVE TO DIRECTORY FILE and press Enter. The Directory File
popup window appears (see Figure 3-28).
Figure 3-26 UNIQUE ID DIRECTORY FUNCTION
Figure 3-28 FILE NAME MENU
11. Move the cursor to highlight the desired file and
press Enter. The file is saved and automatically
exits to the Unique ID Directory popup window.
2. Move the cursor to highlight the desired entry line.
3. Type the name for this UID or press the right arrow
key if no name is assigned.
12.To LOAD an existing file press the LOAD/ SAVE
FILE key and the Load/Save File popup window
appears.
4. Press the Enter key or the right arrow key to move
the cursor, type the Unique ID number (1-8163) and
Priority (1-5).
13.Move the cursor to highlight LOAD FILE and press
Enter. The Directory File popup window appears
(see Figure 3-28).
5. Repeat Steps 2, 3 and 4 until each desired Unique ID
has been created.
14.Move the cursor to highlight the desired file and
press Enter. The file is loaded and automatically
exits to the Unique ID Directory popup window.
NOTE: To clear an existing Unique ID return all
parameters to "0".
6. To SAVE this file press the LOAD/SAVE FILE key
and the Load/Save File popup window appears.
15.To DELETE an existing file press the LOAD/
SAVE FILE key and the Load/Save File popup window appears.
7. Move the cursor to highlight SAVE TO NEW FILE
and press Enter. The File Name popup window
appears (see Figure 3-27).
16.Move the cursor to highlight DELETE FILE and
press Enter. The Directory File popup window
appears (see Figure 3-28).
8. Type in the name of the file and press Enter. The file
is saved and automatically exits to the Unique ID
Directory popup window.
17.Move the cursor to highlight the desired file and
press Enter. The file is deleted and automatically
exits to the Unique ID Directory popup window.
18.To EXIT the Group Directory popup window press
the Escape (ESC) key.
Figure 3-27 FILE NAME POPUP
3-15
September 1995
Part No. 004-3039-272
CONSOLE SETUP
3.8 DTMF DIRECTORY FUNCTION
7. Move the cursor to highlight SAVE TO NEW FILE
and press Enter. The File Name popup window
appears (see Figure 3-27).
NOTE: If the DTMF icon is not present on the screen,
press the TOG M icon key.
8. Type in the name of the file and press Enter. The file
is saved and automatically exits to the DTMF Directory popup window.
The DTMF Directory (DTMF D) function consists of files that contain the definition of up to 32
DTMF groups. The DTMF Directory function allows
the Console Manager to set the Title and DTMF
group. Each of the DTMF groups consists of up to 10
DTMF digits.
9. To ADD to an existing file press the LOAD/ SAVE
FILE key and the Load/Save File popup window
appears.
10.Move the cursor to highlight SAVE TO DIRECTORY FILE and press Enter. The Directory File
popup window appears (see Figure 3-28).
Once the file is created, the file is saved in the
Group directory. Each file can be created and saved to
represent the different Talk Groups for a different configuration. The only limit to the number of files in this
directory is the available space on the hard disk.
11. Move the cursor to highlight the desired file and
press Enter. The file is saved and automatically
exits to the DTMF Directory popup window.
12.To LOAD an existing file press the LOAD/ SAVE
FILE key and the Load/Save File popup window
appears.
The Console Manager is now able to select a file
by scrolling the file names in the directory menu, highlighting the desired file and pressing the Enter key.
This file is automatically loaded and displayed on the
console. To exit the Group Directory function, press
the Escape (ESC) key.
13.Move the cursor to highlight LOAD FILE and press
Enter. The Directory File popup window appears.
14.Move the cursor to highlight the desired file and
press Enter. The file is loaded and automatically
exits to the DTMF Directory popup window.
3.8.1 DTMF DIRECTORY SETUP
1. Press the DTMF icon key. The DTMF Directory
popup window appears (see Section 3.2.24).
15.To DELETE an existing file press the LOAD/
SAVE FILE key and the Load/Save File popup window appears.
2. Move the cursor to highlight the line for the entry.
16.Move the cursor to highlight DELETE FILE and
press Enter. The Directory File popup window
appears (see Figure 3-28).
3. Type the name for this DTMF group or press the
right arrow key if no name is assigned.
4. Press the Enter key to move the cursor to the digits.
Type in the DTMF group (1-10) desired. Press the
Enter key to move to the next entry.
17.Move the cursor to highlight the desired file and
press Enter. The file is deleted and automatically
exits to the DTMF Directory popup window.
5. Repeat Steps 2, 3 and 4 until each desired Unique ID
has been created.
18.To EXIT the Group Directory popup window press
the Escape (ESC) key.
NOTE: To clear an existing DTMF group return all parameters to "0".
3.9 PATCH FUNCTION
6. To SAVE this file press the LOAD/SAVE FILE key
and the Load/Save File popup window appears.
NOTE: If the PATCH icon is not present on the screen,
press the TOG M icon key.
September 1995
Part No. 004-3039-272
3-16
CONSOLE SETUP
3. Press the Call Block key associated with each call
block to be included in this patch. As each call
block is selected an " * " appears on the left border
of the call block.
The patch function can contain up to 16 separate patches, each consists of 2 to 8 entries. This function allows
the selection of 2 to 8 entries to communicate that normally cannot talk to one another. An entry is a Call
Block, Group or Other. Other is a call block or group
from another console.
A Call Block, Group or Other can be associated
with only one patch (see Figure 3-29).
NOTE: The actual number of patches available is
dependent on the number of enabled Group Patch
Modules (GPMs) in the Radio Network Terminal
(RNT).
Figure 3-32 CALL BLOCK
4. If Groups are to be included in the patch, press the
GRP D icon key. The Group Directory popup window appears (see Figure 3-24).
5. Move the cursor to highlight the Group to be
included in the patch. As the group is selected an
"*" appears in the column marked "P".
6. Exit the Group Directory popup window by pressing
the Escape (ESC) key.
Figure 3-29 SETUP PATCH
7. After all the entries for this patch have been selected
press the PATCH icon key. The patch number
assigned this patch will now be displayed in place of
the "*" by all the entries involved.
3.9.1 PATCH SETUP
1. Press the PATCH icon key. The Patch function
popup window appears (see Figure 3-30).
8. An Error popup window appears if the patch fails to
be setup.
9. Repeat Steps 1 through 7 for each patch required.
3.9.2 VIEW/DELETE PATCH
Figure 3-30 SETUP PATCH WINDOW
2. Move the cursor to highlight SETUP PATCH and
press Enter. The Patch Instructional popup window
appears (see Figure 3-31).
Figure 3-33 VIEW/DELETE PATCH WINDOW
10.Press the PATCH icon key. The Patch function
popup window appears (see Figure 3-30).
11. Move the cursor to highlight View/Delete Patch and
press Enter. The Patch popup window appears (see
Figure 3-29) displaying the current status of all the
16 possible patches.
Figure 3-31 PATCH INSTRUCTIONAL WINDOW
3-17
September 1995
Part No. 004-3039-272
CONSOLE SETUP
3.10 TONES FUNCTION
12.To only view the current patches, scroll the patches
up or down as needed.
13.To exit the View/Delete Patch popup window press
the Escape (ESC) key.
Refer to Figure 3-35 for an example of tones and
pause strings.
14.To delete an entire patch, move the cursor to highlight the Patch Number and press Enter.
NOTE: If the TONES icon is not present on the screen,
press the TOG M icon key.
15.To delete a single entry of a patch, move the cursor
to highlight the entry and press Enter.
16.To exit the Patch function popup window press the
Escape (ESC) key.
3.9.3 ADD TO A PATCH
Figure 3-35 TONES POPUP WINDOW
The tones function is used to transmit different
alert tones or tones and pause combinations from the
console. The maximum length and string of tones/
pauses is 30 characters. Tones are entered by the Tone
Number and a comma "," represents a pause (See
Table 3-2). Each character is 150 milliseconds long
and can be duplicated to create different time durations
of tones and pauses. The maximum number of Tone
Names is 32 with 10 characters maximum for each
name.
Figure 3-34 ADD TO PATCH WINDOW
1. Press the PATCH icon key. The Patch function
popup window appears (see Figure 3-30).
2. Move the cursor to highlight ADD TO PATCH and
press Enter.
Table 3-2 TONE NUMBERS
3. The Patch popup window appears (see Figure 3-29)
displaying the current status of all the 16 possible
patches.
Frequency
Number
0
1
2
3
4
5
6
7
4. Move the cursor to highlight the Patch Number
desired and press the Enter key. The Patch popup
window disappears.
5. Select the additional Call Block or Group to be
added to the active patch. This is done by pressing
the desired Call Block key or by highlighting the
desired Group in the Group Directory and press the
Enter key. The Patch number appears on the left
border of the Call Block or in the column marked
"P" of the desired Group.
3.10.1 SETUP TONES
1. Select the TONES icon and press Enter. On the custom keyboard press the TONES icon key.
6. To exit the Patch function popup window press the
Escape (ESC) key.
September 1995
Part No. 004-3039-272
Frequency
in Hz
697
770
852
941
1209
1336
1477
1633
2. Move the cursor to highlight the number for the
Tone Name.
3-18
CONSOLE SETUP
After all the tone names and strings have been
entered, exit the Tones function by pressing the escape
(ESC) key or this setup can now be placed in a file for
future reference. Refer to Save Selection Files on
page 6 for information on how to save files. On the
custom keyboard press the SAVE FILE key.
3. Enter the name of the mnemomic or reference for
this tone string and press Enter.
4. Enter the tone string. Refer to the example in Figure
3-35. The following are descriptions of the strings
shown in the example:
To exit the tones function press the escape (ESC)
TONE 1 is named "Tone Name1" (maximum of
10 characters). The tone sequence is 25. When
TONE 1 is selected and the PTT pressed, 852 Hz is
transmitted for 150 milliseconds and 1336 Hz is transmitted for 150 milliseconds. The transmitter then
stays keyed to allow the operator to give the message
after the tones. Press the PTT to disable the transmitter.
key.
3.11 COLOR CHANGES
The colors on the display may be changed. The
color palette window is activated by pressing the
COLOR key on the custom keyboard. Colors cannot
be activated or manipulated with the mouse.
TONE 2 is named "Tone Name2". The tone
sequence is 47,,27,,45,,67. When TONE 2 is selected
and the PTT pressed, 1209 Hz is transmitted for 150
milliseconds, 1633 Hz for 150 milliseconds, pause for
300 milliseconds, 852 Hz for 150 milliseconds, 1633
Hz for 150 milliseconds, pause for 300 milliseconds,
1209 Hz for 150 milliseconds, 1336 Hz for 150 milliseconds, pause for 300 milliseconds, 1477 Hz for 150
milliseconds and 1633 Hz for 150 milliseconds. The
transmitter then stays keyed to allow the operator to
give the message after the tones. Press the PTT to disable the transmitter.
NOTE: The different windows are interrelated.
When using the normal keyboard use the keys as
defined in the window’s border to manipulate the colors. The custom keyboard uses the same keys with
some exceptions, see Table 3-3.
Table 3-3 KEYBOARD FUNCTIONS
Keyboard
TONE 3 is named "Tone Name3". The tone
sequence is 333333666. When TONE 3 is selected
and the PTT pressed, 941 Hz is transmitted for 900
milliseconds and then 1477 Hz
Function
RGB Up
RGB Down
Move Window Up
Move Window Down
Save
Defaults
for 450 milliseconds. The transmitter then stays
keyed to allow the operator to give the message after
the tones. Press the PTT to disable the transmitter.
3-19
Standard
PgUp
PgDn
Ctrl PgUp
Ctrl PgDn
End
Home
Custom
Shift ↑
Shift ↓
Ctrl ↑
Ctrl ↓
Ctrl E
Ctrl H
September 1995
Part No. 004-3039-272
CONSOLE SETUP
September 1995
Part No. 004-3039-272
3-20
ENCRYPTION
SECTION 4 ENCRYPTION
4.1 MODIFYING EXISTING FILES
4.2 BLOCK DIRECTORY
Before using the Encryption option, any saved
Call Block and UID files must be converted. A utility
on the Console installation disk has been provided to
change these files.
The functions of Block Directory are as described
in Section 3.5, with the addition of two encryption
fields (see Figure 4-1). The field for encryption mode
(E) contains the encryption mode for the Call Block.
The encryption code field (CD) contains the encryption code (1-16) for the Call Block. The encryption
codes correspond to hexadecimal values 0-F and control the encryption module select lines.
To use the utility:
1. Copy the modify.exe file from the Console installation disk to the Console directory on the hard drive.
4.3 UNIQUE ID DIRECTORY SETUP
2. Type modify, then press Enter.
The Unique ID Directory operates as described in
Section 3.7.1, with the addition of the encryption
mode field. The "E" denotes encrypted transmissions
and "C" means transmission is in clear mode (see Figure 4-2).
The modified files will be loaded when the Console is started. The old Call Block files are saved as
<filename>.bak and the old UID files are saved as
<filename>.old. The encryption mode will be Clear
in all files.
Figure 4-1 BLOCK DIRECTORY
Figure 4-2 ENCRYPTION TITLE BLOCK
4-1
September 1995
Part No. 004-3039-272
ENCRYPTION
September 1995
Part No. 004-3039-272
4-2
911 INTERFACE
SECTION 5 911 INTERFACE
5.1 MICROPHONE INPUTS
An active low, open collector PTT output is provided to the console PTT input, which is an "OR" connection of the PTT and Paging Enable.
The 911 interface module has three microphone
inputs: Desk, Console Operator, and Supervisor.
5.3 OPERATOR AND SUPERVISOR EAR OUTPUTS
The Operator and Supervisor microphones are 1/4
inch jacks with headsets that plug into a jackbox. An
operator and supervisor can both listen to an incoming
phone call at the same time, but only one microphone
can be live. The operator’s microphone is normally
active, but the supervisor’s microphone can intercede
when the supervisor PTT or the supervisor takeover is
used.
The operator and supervisor ear outputs sum
together four inputs: Console Audio, Instant Recall,
Intercom and the Incoming Phone Call (911 Audio
Input). Both ear outputs are always live during the
911 call. 911 audio input is controlled by 911 Active
and has a four position volume control switch (S1) on
the jack box.
The desk microphone is wired to two of the PC
board termination blocks. It can be used only when
the operator microphone jack is unplugged. The desk
microphone will then function as the operator microphone. Also, when the desk microphone is active,
audio to the 911 console is muted.
911 Recorder Output provides a recording for
both microphone and earpiece audio.
Select Speaker Audio (output) is routed to this
module. Jumper programming allows the Select
Audio to be; always off, always on, or becomes active
when 911 Active becomes live. This allows for console audio to be switched from the headsets to the
select speaker during 911 calls. In addition, using
jumper programming again, the select speaker audio
can be enabled whenever the operator’s jack is
unplugged (used then with the desk microphone).
5.2 MICROPHONE OUTPUTS
The microphone audio is routed to four outputs:
Console Microphone, Auxiliary, 911 Audio Output,
and PA Output.
Console microphone output is active when either
the operator or supervisor PTT is active or when the
paging enable is activated. When paging enable is
active, both microphones are muted and paging
encoder is routed to the console mic output.
5.4 CIRCUIT DESCRIPTION
5.4.1 GENERAL
The 911 Interface module is used with the
TRACER console to provide an interface to a 911 console, the building PA system, an instant recall recorder,
an intercom system, plus provides ability for a dispatcher supervisor to take over operation of the console.
Auxiliary output is always active when the microphone audio is active.
911 audio output is active when the 911 active
logic input is active and neither PTT, PA Enable, or
Paging Enable is active. With jumper programming,
the PC board can allow 911 audio output to stay
active, regardless of the states of the PTTs and enables.
The exception is when the desk microphone option is
used, this mutes the 911 audio out and the 911 recorder
output.
5.4.2 INPUTS
All audio inputs to the 911 Interface module are
balanced inputs and provide for input impedances of
120, 620 or 910 ohms by plug-in jumper programming. In addition, selection of 300 or 3.9k ohm
impedance with a bias voltage of 2.5V or 620 ohms
with a bias voltage of 12V is provided with plug-in
The PA output is active when PA Enable is active.
5-1
September 1995
Part No. 004-3039-272
911 INTERFACE
4. 911 Audio (audio input from a 911 console)
jumper programming. Separate gain adjust trim
potentiometers are provided for each audio input. All
PTT inputs are active low with pull-up resistors to 5V.
The 911 audio input is transformer coupled for added
hum protection.
5. Console Audio (audio input from the TRACER console)
6. Instant Recall (from an instant recall recorder)
5.4.3 HEADSETS
7. Paging Input (audio from a paging encoder)
Headsets are Plantronics type with noise reduction boom microphone (with wind screen) and a single
earpiece (with cushion). The headband is fully adjustable. A stress relief clip (or clothes clip) provides tension relief from the headset assembly. The stress relief
clip is adjustable anywhere between the headset
assembly and approximately four feet down the length
of the cord. Each headset cord is coiled with a ten foot
extended length. The end connector is a plug-prong
type with tip-sleeve ends.
8. Operator PTT (active low from an operator’s PTT
switch)
9. Supervisor’s PTT (active low from a supervisor’s
PTT switch)
10.Supervisor Take-Over (active low from supervisor’s
override)
11. PA Enable (active high or low input to enable the
building PA system)
5.4.4 TELEPHONE/HEADSET INTERFACE
A Telephone/Headset Interface enables the operator to use a headset for both radio and telephone operation. When a telephone line is selected, the selected
channel audio is automatically transferred to the
selected speaker and the headset microphone and earpiece are connected to the telephone. If communication on a radio circuit is necessary, the telephone transmit audio to the caller is automatically suspended
when the transmit switch is pressed and the headset
microphone audio is transferred to the radio circuit.
The telephone caller does not hear the radio transmissions.
12.911 Active (active high or low corresponding to an
on-line condition of the 911 console)
5.4.5 CONTROL INPUTS
5.4.6 OUTPUTS
Other control inputs can be configured for active
high or active low by plug-in jumper programming.
When configured for active low, pull-up resistors are
provided to 5V.
All audio outputs from the 911 Interface module
are balanced outputs, and have plug-in jumper selectable impedances of 130, 620 or 910 ohms. All outputs
have separate gain adjustments through trim potentiometers with drive capability of 5V RMS into an open
circuit. The 911 audio output is transformer coupled
for added hum protection. The PTT is an active low,
open collector output.
13.Paging Enable (active high or low corresponding to
activation of a paging transmitter)
14.Select Audio (from the console select audio
speaker)
15.Intercom (audio input)
The 911 Interface module provides the following
inputs:
1. Operator’s Microphone (audio input)
The 911 Interface module provides the following
outputs:
2. Desk Microphone (audio input)
1. Console Microphone (audio to the TRACER console microphone input)
3. Supervisor’s Microphone (audio input)
September 1995
Part No. 004-3039-272
5-2
911 INTERFACE
the supervisor’s microphone as long as the supervisor’s
takeover input is active. The desk microphone is inoperative until the operator’s microphone jack is
removed, at which time, the desk microphone is
enabled and functions as the operator’s microphone.
When the desk microphone is active, audio to the 911
console is muted.
2. 911 Audio (audio to the 911 console microphone
input)
3. PA Output (audio to the building PA system microphone input)
4. Operator Earphone (audio output)
Microphone audio is routed to four outputs. The
console microphone output is active any time that
either the operator or the Supervisor PTT is active, or
when the Paging Enable is activated. When the Paging Enable is active, both microphones are muted, and
the paging encoder is routed to the console microphone output. The 911 audio output is active when the
911 Active line is activated, and neither PTT, PA
Enable, or Paging Enable is active. The PTT and
Intercom may be programmed individually by plug-in
jumpers to be disregarded for the 911 Audio output
control. The exception is when the desk microphone
option is used, this mutes the 911 audio out and the
911 recorder output. The PA output is active when the
PA Enable is active. The Auxiliary output is always
live for the selected microphone.
5. Supervisor Earphone (audio output)
6. PTT Out (active low, open collector to the console
PTT)
7. Auxiliary (audio output)
8. 911 Recorder (recorder for all 911 activity)
9. Select audio (audio to the select audio speaker)
5.4.7 MECHANICAL ASSEMBLIES
The 911 Interface module consists of two
mechanical assemblies. The main assembly is a
printed circuit board that attaches to the sheet metal
panel and has a snap on dust cover. This assembly
replaces the DCC in the console. This assembly contains all of the electronics for the 911 Interface module. It is interfaced into the console much the same as
the DCC.
The 911 Interface module has two earpiece audio
outputs. Both outputs are active at all times. The outputs are a summation of the 911 Audio, Console Select
Audio, Intercom Audio, and the output of an Instant
Recall Recorder. The 911 audio is gated with the 911
Active status. The 911 audio has an independent volume control consisting of four levels. This volume is
controlled by a 4-position rotary switch located in the
small connector box located under the console writing
surface. The 911 Recorder output provides for recording both the 911 microphone and earpiece audio.
The second connector assembly is constructed in
an extruded shell, and is mounted beneath the console
writing surface. This box contains the connectors for
the operator’s and supervisor’s headsets, along with the
volume control for the 911 earpiece audio. Headset
connections are made through 1/4" phone jacks. Connections from this module to the main 911 Interface
module is through ribbon cables with connectors.
The Select Speaker audio is routed to the 911
Interface module. Select audio is jumper programmed for either always on, always off, or becomes
active when the 911 Active line is enabled. This
allows for console audio to be switched from the headset to the select speaker during 911 calls. In addition,
by jumper programming, the Select Speaker audio can
be enabled whenever the operator’s earpiece is
unplugged and the desk microphone is also used.
5.4.8 THEORY OF OPERATION
Refer to Figure 5-1 for details of the operation of
the 911 Interface module.
The 911 Interface module has three microphone
inputs, one each for; the Console Operator, Desk
microphone, and the Supervisor. At any time only one
microphone is live. Normally the operator’s microphone is active, however, the supervisor’s microphone
becomes active when the Supervisor PTT is pressed.
There is also a supervisor takeover input that activates
A PTT output is provided to the console PTT
input, which is an "OR" connection of the Operator
PTT, the Supervisor PTT, and the Paging Enable.
5-3
September 1995
Part No. 004-3039-272
911 INTERFACE
Figure 5-1 911 INTERFACE BLOCK DIAGRAM
Table 5-1 JUMPER PROGRAMMING FOR INPUT BLOCKS
Bias Voltage
Impedance
Paging Audio ± (J24, 1-21)
Desk Mic ± (J83, 1-21)2
Operator Mic ± (J29, 1-21)
Supervisor Mic ± (J34, 1-21)
911 Audio Input ±
Console Audio ± (J39, 1-21)
Intercom ± (J44, 1-21)
Instant Recall ± (J49, 1-21)
2.5V
300
J21, 1-2
J80, 1-2
J26, 1-2
J31, 1-2
12V
620
J22, 1-2
J81, 1-22
J27, 1-21
J32, 1-21
2.5V
3.9k
J23, 1-2
J82, 1-2
J28, 1-2
J33, 1-2
J36, 1-2
J41, 1-2
J46, 1-2
J37, 1-2
J42, 1-21
J47, 1-21
J38, 1-2
J43, 1-2
J48, 1-2
1
2
These jumpers ground the negative terminal of the corresponding input.
Challenger desk microphone.
3 Shure boom microphone.
September 1995
Part No. 004-3039-272
5-4
0V
120
J21, 2-3
J80, 2-33
J26, 2-3
J31, 2-3
J20, 1-2
J36, 2-3
J41, 2-3
J46, 2-3
0V
620
J22, 2-31
J81, 2-3
J27, 2-3
J32, 2-3
J20, 3-41
J37, 2-31
J42, 2-3
J47, 2-3
0V
910
J23, 2-3
J82, 2-3
J28, 2-3
J33, 2-3
J20, 5-6
J38, 2-3
J43, 2-3
J48, 2-3
911 INTERFACE
Table 5-2 JUMPER PROGRAMMING FOR OUTPUT BLOCKS
Impedance
68
300*
Console Mic+
J51, 1-2
J51, 3-4
Console MicJ52, 5-6
J52, 3-4
Auxiliary +
J61, 1-2
J61, 3-4
Auxiliary J62, 5-6
J62, 3-4
911 Audio Out +
J63, 1-2
J63, 3-4
911 Audio Out J64, 5-6
J64, 3-4
PA Output +
J65, 1-2
J65, 3-4
PA Output J66, 5-6
J66, 3-4
911 Recorder +
J56, 1-2
J56, 3-4
911 Recorder J57, 5-6
J57, 3-4
Operator Ear +
J67, 1-2
J67, 3-4
Operator Ear J68, 5-6
J68, 3-4
Supervisor Ear +
J69, 1-2
J69, 3-4
Supervisor Ear J70, 5-6
J70, 3-4
* Standard configuration of jumpers.
430
J51, 5-6
J52, 1-2
J61, 5-6
J62, 1-2
J63, 5-6
J64, 1-2
J65, 5-6
J66, 1-2
J56, 5-6
J57, 1-2
J67, 5-6
J68, 1-2
J69, 5-6
J70, 1-2
Table 5-3 JUMPER PROGRAMMING FOR LOGIC BLOCKS
Low to activate [1]
J13, pins 2-3*
High to activate [1]
J13, pins 1-2
Paging Enable
on J9, pin 21
PA Enable
J14, pins 2-3(A)
J14, pins 1-2(A)
on J9, pin 22
911 Active
J15, pins 2-3(B)*
J15, pins 1-2(B)
on J9, pin 23
[1] This is the output state of the console when a logic block is selected.
Jumper
Output Result
J16, 1-2
Logic High
(+5V)
J16, 2-3*
Logic Variable
(PTT Out and Output Tx Active)
5-5
Disabled
J13, pin 1 only
J14, pin 1 only*
J15, pin 1 only
Affects
911 Audio Output
September 1995
Part No. 004-3039-272
911 INTERFACE
Table 5-3 JUMPER PROGRAMMING FOR LOGIC BLOCKS
Low to activate [1]
High to activate [1]
Disabled
J17, 1-2*
Logic High
(+5V)
911 Audio Output
J17, 2-3
Logic Variable
(J14, pin 2 and PA Enable)(A)
J18, 1-2*
Logic Variable
(J15, pin 2 and 911 Active)(B)
J19, pin 1 and Console Audio
J18, 2-3
Logic Low
(Ground)
J19, 1-2
Logic Variable
(J18, pin 2)
Select Audio
J19, 2-3*
Logic Variable
(High or J99, pin 2 Op Mic Sense)
J99, 1-2
Logic Variable
(Op Mic Sense [Low or Open])
J19, pin 3
J99, 2 only*
Disabled
Comments in parenthesis explain what would influence the logic to be High, Low, or Variable (includes pin numbers or
inputs).
* Standard configuration for jumpers.
September 1995
Part No. 004-3039-272
5-6
911 INTERFACE MODULE INSTALLATION AND SETUP
SECTION 6 911 INTERFACE MODULE INSTALLATION AND SETUP
6.1 CONSOLE HARDWARE CONFIGURATION
Table 6-2 INTERFACE CONNECTIONS
The Console consists of 13 different pieces of
hardware (see Table 6-1). Figure 6-1 is a block diagram of how each piece of hardware fits together to
create the Console and how the Console is interconnected.
Device
911 Jack Box
Console Audio Panel
IDC Audio Interface Card
PCM Summation Card
I/O Alarm Relay Card
IDM Intelligent Dispatch Module
5 ft F/F 9-pin RS-232 Cable
5 ft M/M 25-pin RS-232 Cable
Table 6-1 CONSOLE HARDWARE
Hardware
Console Audio Panel
IDC Audio Interface Card
Encrypted Console IDC
Console Custom Keyboard
PCM Summation Board
911 Interface Module
Includes:
911 Jack Box
Modular Jack Adapter Cable
Footswitch*
8 ft. AC Cord 3/18 black*
Console Computer**
Trackball Mouse
5 ft F/F 9-pin RS-232 Cable
5 ft M/M 25-pin RS-232 Cable
* Footswitch requires an AC cord.
** Consult EF Johnson.
Part Number
023-3039-260
023-3039-280
023-3039-283
023-3039-285
023-3039-780
023-3039-900
Section
6.3
6.4
6.5
6.6
6.7
6.8
Figure 6.1
Figure 6.5
Table 6-3 LINE ITEMS/ACCESSORIES
Desk Microphone
I/O Alarm Relay Card***
Profile III Headset**
GN Netcom Monaural
and 1./4" phone jack
Plantronics Monaural*
Plantronics Binaural*
Plantronics Mirage (earhook)*
* Includes plug prong adapter.
** Before 7/18/94.
*** See Section 6.7
023-3039-910
023-7175-807
583-4001-014
597-1001-002
583-3000-xxx
585-3000-127
597-0005-035
597-4003-001
Part Number
250-0742-010
585-3000-134
589-2006-023
589-9006-024
589-9006-030
589-9006-031
589-9006-032
6.3 911 JACK BOX
The Jack Box provides 1/4" phone jacks for both
the operator’s and supervisor’s headsets and has a level
control for 911 earpiece audio. The operator’s microphone jack also enables/disables the desk microphone
operation. The 911 Jack Box comes with an interface
cable that plugs directly into P2 of the 911 board.
6.2 911 INTERFACE MODULE
The 911 Interface Module is the interconnecting
point for all the console’s external devices (see Figure
6-1, Tables 6-2 and 6-3).
6-1
September 1995
Part No. 004-3039-272
911 INTERFACE MODULE INSTALLATION AND SETUP
Figure 6-1 CONSOLE BLOCK DIAGRAM WITH 911 INTERFACE
6.4 CONSOLE AUDIO PANEL
The jumpers and switches on the Audio Interface
Card must be setup and selected before installation
and alignment.
The Console Audio Panel contains the select and
unselect speaker. Each speaker has an associated mute
switch. The audio is muted by switching to a 3.3 ohm
load and muting is indicated by a light within the
switch being turned on. The console audio panel
includes two speaker coaxial cables that plug directly
into jacks J4 and J5 of the 911 board.
6.5.1 JUMPER DESCRIPTION
J2
Connects microphone - input to ground, to
+12V or open.
6.5 IDC AUDIO INTERFACE CARD
J3
Connects Select Audio for 600 ohm input.
The IDC Audio Interface Card logic board controls the audio to and from the console. A
5 foot male/male 25-pin RS-232 cable is used to connect J7 of the IDC card to J1 of the 911 board.
J4
Connects Unselect Audio - input to ground.
J5
Connects Unselect Audio for 600 ohm input.
J8
Connects 10k pull-up resistor to +5V for
non-used input.
NOTE: Console IDC board, Revision 4.0 or older
needs the following modifications made to supply
+12V to the 911 Interface Module.
J10 Connects microphone + input to +2.5V via
300 ohms.
1. Remove U27.
J11 Connects microphone + input to +12V via
1240 ohms.
2. Jumper U14, pin 5 to J7, pin 12.
J12 Connects microphone + input to +2.5V via
6100 ohms.
3. Jumper J7, pin 11 to J7, pin 12.
4. Jumper J7, pin 13 and J7, pin 14 to ground.
September 1995
Part No. 004-3039-272
6-2
911 INTERFACE MODULE INSTALLATION AND SETUP
Recorder Summation Output Selection
(On = Summed Output)
J28* Microphone audio output.
J29 Unselect speaker output.
J30 Select speaker output.
J31* Headset earpiece output.
J13 Provides high Z (10k) audio path for headset
+ output.
J14 Provides low Z (300) audio path for headset
+ output.
J15 Provides non DC blocked audio path for head
set + output (+2.5V).
Microphone Input
J16 Provides ground for headset - output.
Headset Microphone
J17 Connects Select Audio - input to ground.
J10
J11
J12
J18*
J2
J18 Connects microphone input for 600 ohm input.
J28 Connects microphone audio to recorder
summation output.
Off
Off
On Provides +2.5V via 600 ohms.
Off Provides high impedance input.
Pins 2 and 3. Provides DC ground return.
Deskset Microphone
J29 Connects Unselect Audio to recorder
summation output.
J10
J11
J12
J18
J2
J30 Connects Select Audio to recorder
summation output.
J31 Connects Headset Receive Audio to recorder
summation output.
Off
On Provides +12V via 1240 ohms.
Off
Off Provides high impedance input.
Pins 1 and 2. Provides +12V to desk mic.
Ground path provided by PTT DC return.
6.5.3 SWITCH SETTINGS
6.5.2 JUMPER USAGE
S1 and S2 provide the address for the audio card,
for example address 0C00h. FACTORY SET DO
NOT TOUCH.
NOTE: * indicates the standard configuration "on",
other jumper "off".
Unselect Audio Input
J5*
J4
On
Off
Provides 600 ohm input.
Provides balanced input.
Select Audio Input
J3*
J17
On
Off
Provides 600 ohm input.
Provides balanced input.
Figure 6-2 AUDIO CARD S1
Headset Earpiece (headset 589-9006-024)
J13
J14*
J15*
J16*
Off
On
On
On
No high impedance.
Provides low impedance 300 ohm output.
Provides for +2.5V DC output.
Provides for DC ground return.
Figure 6-3 AUDIO CARD S2
6-3
September 1995
Part No. 004-3039-272
911 INTERFACE MODULE INSTALLATION AND SETUP
6.6 PCM SUMMATION CARD
6.7.2 ALARMS
The PCM Summation Card sums the audio for
the unselect audio (see Figure 6-11).
The SMM monitors for alarm activity in the system and can set the various output relays as defined by
the user. When an external alarm relay is set, a timestamp record is recorded in the device activity log.
The alarms are cleared by the SMM operator in a simple selection by alarm number. Refer to System Management Module Operator’s Manual, Part No. 0023039-075.
1. The PCM summation board is installed on the IDM
board at the factory.
2. Insert the IDM into the slot connected to the DCC.
3. On the IDM select Test "9" by setting S5 to a "9"
(See Figure 6-8).
6.7.3 OUTPUTS
The alarm relay outputs are provided via a DB-37
pin connector. Refer to Table 6-4.
4. On a CIM select test "9" by setting S5 to a "9".
5. Connect a transmission test set to TP1 and adjust R1
for +2.5 dBm.
Table 6-4 ALARM RELAY OUTPUTS
6. Connect a transmission test set to TP2 and adjust
R25 for -3 dBm.
Alarm
1. OP0
2. OP1
3. OP2
4. OP3
5. OP4
6. OP5
7. OP6
8. OP7
7. Reset S5 on the CIM/IDM (close all sections).
6.7 I/O ALARM RELAY CARD
The I/O Alarm Relay Card contains 8 input contacts and 8 output contacts. The 8 inputs can be connected for either active high or active low. The 8 output contacts are dry contacts.
Common
37
17
34
14
31
11
10
9
NO Pin
19
36
16
33
13
30
29
28
6.7.4 RELAY INPUTS
The isolated inputs are driven by either AC or
DC signals and are not polarity sensitive. Input signals are rectified by a diode bridge and connected
across the LED of an opto-isolator. A 470 ohm resistor in series dissipates unused power. Standard 12/
24V AC control transformer outputs can be accepted
as well as DC voltages. The input voltage range is 524V RMS. External resistors connected in series may
be used to extend the input voltage range. Refer to
Figure 6-5 and Table 6-5.
The Alarm Relay Module (ARM) activates relays
when alarm trigger events occur in the System Management Module (SMM). The ARM provides 8 relay
outputs (5 SPDT and 3 SPST). The relays have a 2
amp rating.
6.7.1 SETUP
The ARM is an I/O card that is inserted in an
expansion slot of the System Management Module
computer. The ARM must be set for a specific
address by setting S1 for 350 (hex), see Figure 6-4.
Each input circuit contains a switchable slow/fast
filter with a 10 ms time constant (without filtering, the
response is 20 µs). The filter must be selected for AC
inputs in order to eliminate response to zero crossings.
The filter is also valuable for use with slow DC input
signals in a noisy environment. The filter may be
switched out for DC inputs in order to obtain faster
response. Filters are individually selected by switch
S3: IP0 is controlled by S3-1, IP1 by S3-2, IP2 by
S3-3, etc.
Figure 6-4 S1 350 HEX
September 1995
Part No. 004-3039-272
NC Pin
18
35
15
32
12
----
6-4
911 INTERFACE MODULE INSTALLATION AND SETUP
6.7.5 RELAY OUTPUTS
The electromechanical relay outputs are comprised of five FORM C SPDT outputs and three
FORM A SPST (normally open) type. The relays
are all de-energized at power-on. Data to the
relays is latched by a write to the base address. On/off
status of the relays can be read back by a read at the
base address.
6.7.6 CONNECTOR PIN ASSIGNMENTS
Table 6-5 CONNECTOR PINOUTS
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
Name
IP7
IP6
IP5
IP4
IP3
IP2
IP1
IP0
OP7(C)
OP6(C)
OP5(C)
OP4(NC)
OP4(NO)
OP3(C)
OP2(NC)
OP2(NO)
OP1(C)
OP0(NC)
OP0(NC)
IP7
IP6
IP5
IP4
IP3
IP2
IP1
IP0
OP7(NO)
OP6(NO)
OP5(NO)
OP4(C)
OP3(NC)
OP3(NO)
OP2(C)
OP1(NC)
OP1(NO)
OP0(C)
Function
Digital Input Bit 7
Digital Input Bit 6
Digital Input Bit 5
Digital Input Bit 4
Digital Input Bit 3
Digital Input Bit 2
Digital Input Bit 1
Digital Input Bit 0
Bit 7 Relay Common
Bit 6 Relay Common
Bit 5 Relay Common
Bit 4 Relay, NC Contact
Bit 4 Relay, NO Contact
Bit 3 Relay Common
Bit 2 Relay, NC Contact
Bit 2 Relay, NO Contact
Bit 1 Relay Common
Bit 0 Relay, NC Contact
Bit 0 Relay, NO Contact
Digital Input Bit 7
Digital Input Bit 6
Digital Input Bit 5
Digital Input Bit 4
Digital Input Bit 3
Digital Input Bit 2
Digital Input Bit 1
Digital Input Bit 0
Bit 7 Relay, NO Contact
Bit 6 Relay, NO Contact
Bit 5 Relay, NO Contact
Bit 4 Relay Common
Bit 3 Relay, NC Contact
Bit 3 Relay, NO Contact
Bit 2 Relay Common
Bit 1 Relay, NC Contact
Bit 1 Relay, NO Contact
Bit 0 Relay Common
6-5
September 1995
Part No. 004-3039-272
911 INTERFACE MODULE INSTALLATION AND SETUP
Figure 6-5 RELAY BLOCK DIAGRAM
September 1995
Part No. 004-3039-272
6-6
911 INTERFACE MODULE INSTALLATION AND SETUP
6.8 IDM PRE-ALIGNMENT
Headset Audio Adjust
The Intelligent Dispatch Module (IDM) to which
the dispatch console is attached must be aligned using
the procedure in the RNT Manual, Part No. 001-3039008, and have an aligned PCM Summation board (secondary audio board) attached to it.
1. On the DCC monitor, verify the headset volume
control (H) is at minimum audio level
("2" - 1 bar) see Figure 6-6.
2. On the IDC board, connect a transmission test set to
EP5 and adjust R3 for -30 dBm.
There must be at least one pre-aligned Channel
Interface Module (CIM) card in the switch to align the
IDC card. Refer to Figure 6-10 for IDC audio alignment points. Refer to the Multi-Net RNT Service
Manual, Part No. 001-3039-100 for information on the
CIM and IDM modules.
Unselect Audio Adjust
1. On the IDM select test "9" by setting S5 to a "9" (the
IDM must have a pre-aligned PCM Summation
board connected to it). See Section 6.6.
6.8.1 RECEIVE AUDIO ALIGNMENT
Install the IDC audio board into a working Dispatch Computer Console (DCC) connected to an Intelligent Dispatch Module (IDM).
Adjust all the audio sources to a minimum (level of
"2" - 1 bar) on the console monitor (Headset, Selected
and Unselected) see Figure 6-6.
Figure 6-8 S5 TEST 9
2. On a CIM select test "9" by setting S5 to a "9".
3. On the DCC monitor verify, the unselect audio volume control (U) is at minimum audio level ("2" - 1
bar) see Figure 6-6.
Figure 6-6 DCC CONSOLE AUDIO
Select Audio Adjust
4. On the IDC board, connect a transmission test set to
EP7 and adjust R6 for -12 dBm.
1. On the IDM select Test "1", set S5 to a "1".
5. On the IDC board, connect a Transmission test set to
EP8 and adjust R7 for -40 dBm.
6.8.2 TRANSMIT AUDIO ALIGNMENT
On the IDC board, inject 1 kHz tone at 0 dBm
across J7, pins 1 and 2 (microphone input).
Figure 6-7 S5 TEST 1 SETTING
J7, pin 1 = Jumper 10, pin 2
J7, pin 2 = Jumper 2, pin 2.
2. On the DCC monitor, verify the select audio volume
control (S) is at minimum audio level ("2" - 1 bar)
see Figure 6-6.
Microphone Input Audio Adjust
3. On the IDC board, connect a transmission test set to
EP4 and adjust R5 to -12 dBm.
1. Connect a transmission test set to EP2.
4. On the IDC board, measure the level at EP6 and
adjust R4 to -40 dBm.
2. Adjust R9 for -5 dBm.
6-7
September 1995
Part No. 004-3039-272
911 INTERFACE MODULE INSTALLATION AND SETUP
Microphone Audio Adjust
6.9 911 INTERFACE ALIGNMENT
1. Connect a transmission test set to EP3.
6.9.1 911 TUNING PROCEDURE/GUIDELINES
2. Key the operator PTT.
This tuning procedure covers all audio inputs,
audio outputs, and the 15 potentiometers that are
located on the 911 Interface PC board.
3. Adjust R8 for -12 dBm.
The following tuning procedures and the jumper
programming shown in Figure 6-12 are for testing
audio inputs and outputs and may have to be adjusted
and reprogrammed according to individual needs.
4. Unkey the operator PTT.
Recorder Level Adjust
Preset the 911 Jack Box Level Adjust. Switch to
maximum (fully clockwise). This controls the 911
audio only.
1. Jumper J28, pin 1 to pin 2.
2. Connect a transmission test set to EP9.
Preset the Headset Volume Control (if equipped)
to a minimum, midrange comfortable setting.
3. Key the operator PTT.
4. Adjust R2 for -12 dBm.
Preset the Console Audio Levels. Verify that the:
Set Headset, Select and Unselect Volume Controls are
at minimum (level of "2" - 1 Bar).
5. Unkey the operator PTT.
Remove the 1 kHz injected signal from J7.
(Remove the jumper of J28 if the optional recorder is
not used.)
NOTE: Console audio Levels adjust Digital 100k ohm
pots, which control the gain of OP amps. The levels
set will affect adjustments and levels of both the IDC
card and the 911 Interface Module. This procedure
uses the minimum level of "2" for alignment purposes.
DTMF Output Adjust
After alignment the console operators can tailor
the Console Audio levels to individual needs (Console Audio panel has a mute feature).
On the Console: Press TOG M; Press SETUP;
and select setup window appears. Select DTMF level
adjust and press Enter.
The console operator can also pad down (coarse
adjust) the output of the 911 amplifier to the operator/
supervisor earphone and 911 output/recorder input by
rotating the Jack Box level control counterclockwise.
1. Connect transmission test set to EP1.
2. Adjust R1 for -12 dBm.
The Headset Level can be adjusted (fine) by the
Volume Control of the headset (if equipped).
DTMF Loopback Adjust
1. Connect a transmission test set to EP10.
6.9.2 HEADSET MICROPHONE INPUT/ CONSOLE MICROPHONE OUTPUT
2. Adjust R100 for -12 dBm.
3. Press any key to clear.
(Unplugging the operator’s headset will load the circuit)
On the 911 Interface Board:
4. Press TOG M to return to normal screen.
September 1995
Part No. 004-3039-272
6-8
911 INTERFACE MODULE INSTALLATION AND SETUP
6.9.4 SUPERVISOR MICROPHONE ADJUSTMENTS
1. Inject a 1 kHz tone into P2, pins 1 and 2.
(A DC blocking capacitor is required.)
(Unplugging the supervisor’s headset will load the circuit)
Audio Level:
GN Profile III (-024) -10 dBm
Plantronics Series (-030/-032) -5 dBm
1. On the 911 Interface Board, key the Supervisory
PTT (J9, pin 18 or 19 to gnd) to gate audio to TP2
(U12, pin 5 High).
2. Adjust R2 for -5 dBm at TP2 (U19, pin 1).
3. Key the Operator’s PTT (J9, pin 20 to gnd) to gate
audio to the console microphone output (U15, pin 6
high).
2. Inject a 1 kHz tone into P2, pins 3 and 4.
(A DC blocking capacitor is required.)
Audio Level:
GN Profile III (-024) -10 dBm
Plantronics Series (-030/-032) -5 dBm
4. Remove jumpers to access J51, pin 4 and
J52, pin 4.
5. Adjust R9 for 0 dBm a J51, pin 4 and
J52, pin 4.
3. Adjust R3 for -5 dBm at TP2 (U19, pin 1).
NOTE: Console Microphone Output Level adjust R9
was previously adjusted with Headset Microphone.
6. Replace jumpers on J51, pin 4 and J52, pin 4.
On the IDC Board:
7. Adjust R9 for -5 dBm at EP2.
4. Verify 0 dBm at the Console Output if desired
(adjust R3 if required).
8. Adjust R8 for -12 dBm at EP3.
5. Unkey the Supervisory PTT on the 911 Board.
9. Unkey the Operator’s PTT on the 911 Board.
6.9.5 PAGING AUDIO
6.9.3 DESK MICROPHONE ADJUSTMENTS
6. On the 911 Interface Board, inject a -15 dBm, 1 kHz
tone into J9, pins 1 and 2.
7. Adjust R1 for -5 dBm at TP1 (U4, pin 7).
NOTE: The Desk microphone is disabled when P2,
pin 14 is Low. Remove the headset jack to enable the
desk microphone option.
NOTE: Console Microphone Output Level adjust R9
was previously adjusted with Headset Microphone.
1. On the 911 Interface Board, inject a 1 kHz tone into
J9, pins 25 and 26.
(A DC blocking capacitor is required if 12V bias is
supplied to the desk microphone.)
1. Verify -5 dBm at the Console Output (adjust R1 if
required).
2. Key Paging Enable (J9, pin 21 to ground) to gate
audio to the console microphone output (U12, pin
13 is High).
Audio Level:
Challenger Desk Microphone -15 dBm
Shure Boom Microphone -30 dBm
3. Unkey Paging Enable.
2. Adjust R8 at TP2 (U19, pin 1) for:
-5 dBm desk microphone
+10 dBm boom microphone
6.9.6 HEADSETS RECEIVE AND CONSOLE
AUDIO
1. Set IDM to a Test 1 (S5 section 1 open, close 2, 3
and 4).
3. Replace Headset Jack into 911 Jack Box.
6-9
September 1995
Part No. 004-3039-272
911 INTERFACE MODULE INSTALLATION AND SETUP
lines. The signal level at a customer’s site can be a
minimum of -17 dB, is typically -7 dB and the maximum is 0 dB. (This is typical only in domestic systems.)
On the Console:
1. verify/adjust the Headset Audio for a level of "2" (1
bar).
If the 911 Board is functioning correctly, there
should not be any insertion loss through the board.
The board should be able to compensate for a low signal level. However, if the Telco audio is suspected to
be below the minimum (-17 dB), the Telco should be
called and asked to check the level present at the site
and correct it.
On the IDC: (see Figure 6-10)
1. Adjust R5 for -12 dBm at EP4.
2. Adjust R3 for -30 dBm at EP5.
1. On the 911 board inject a -17 dBm, 1 kHz tone into
J9, pins 3 and 4.
On the 911 Interface: (see Figure 6-12)
1. Adjust R5 for -30 dBm at TP3 (U10, pin 8).
2. Activate the 911 Active line (J9, pin 23 to ground)
to gate 911 audio to TP3 (audio is also routed to the
operator’s ear, supervisor’s ear and 911 recorder).
2. Remove jumpers to access J67, pin 4 and
J68, pin 4.
3. Adjust R4 for -7 dBm at TP3 (U10, pin 8).
3. Adjust R14 for -25 dBm at J67, pin 4 and
J68, pin 4 (Operator Ear).
4. Replace jumpers on J67, pin 4 and J68, pin 4.
6.9.8 911 TRANSMIT AUDIO AND 911 RECORDER
5. Remove jumpers to access J69, pin 4 and
J70, pin 4.
NOTE: Operator/Headset Microphone Jack must be
plugged in (P2, pin 14 Low) to gate audio to 911
Audio Output/911 Recorder (U15, pin 5 high). This
also disables the Desk Microphone operation.
6. Adjust R15 for -25 dBm at J69, pin 4 and
J70, pin 4 (Supervisor Ear).
7. Replace jumpers on J69, pin 4 and J70, pin 4.
1. On the 911 board inject a 1 kHz tone into P2, pins 1
and 2.
(A DC blocking capacitor is required.)
Audio Level:
GN Profile III (-024) -10 dBm
Plantronics Series (-030/-032) -5 dBm
8. Reset the IDM to normal operation (S5 all sections
On).
NOTE: R2 was previously set.
2. Activate the 911 Active Line (J9, pin 23 to ground
to gate the Operator Microphone to the 911 Audio
Out/911 Recorder).
Figure 6-9 IDM S5 TEST 1
3. Adjust R12 for 0 dBm at J9, pins 11 and 12 (911
Audio Output).
6.9.7 911 RECEIVE AUDIO
4. Adjust R10 for -5 dBm at J9, pins 15 and 16 (911
Recorder).
911 Audio Input is connected directly to the
phone line. The Central Office (CO) is capable of
sending a Test Signal to the customers leased phone
September 1995
Part No. 004-3039-272
6-10
911 INTERFACE MODULE INSTALLATION AND SETUP
6.9.9 OPTIONAL INPUT/OUTPUT ADJUSTMENTS
Intercom
1. On the 911 board inject a -15 dBm, 1 kHz tone into
J9, pins 5 and 6.
2. Adjust R6 for unity gain at TP3 (U10, pin 8).
Instant Recall
1. On the 911 board inject a -15 dBm, 1 kHz tone into
J9, pins 7 and 8.
2. Adjust R7 for unity gain at TP3 (U10, pin 8).
Auxiliary and PA Outputs
1. On the 911 board apply a ground to J9, pin 22 (PA
Enable) to gate audio to PA Output (U15, pin 13
High) (also disables 911 Audio Ouput).
2. Inject a 1 kHz tone into P2, pins 1 and 2.
(A DC blocking capacitor is required.)
Audio Level:
GN Profile III (-024) -10 dBm
Plantronics Series (-030/-032) -5 dBm
3. Adjust R11 for -5 dBm at J9, pins 9 and 10 (Auxiliary Output).
4. Adjust R13 for -5 dBm at J9, pins 13 and 14 (PA
Output).
6-11
September 1995
Part No. 004-3039-272
911 INTERFACE MODULE INSTALLATION AND SETUP
Figure 6-10 IDC ALIGNMENT POINTS
September 1995
Part No. 004-3039-272
Figure 6-11 PCM SUMMATION ALIGNMENT
POINTS
6-12
911 INTERFACE MODULE INSTALLATION AND SET-
Figure 6-12 911 INTERFACE ALIGNMENT POINTS
6-13
September 1995
Part No. 004-3039-272
911 INTERFACE MODULE INSTALLATION AND SETUP
September 1995
Part No. 004-3039-272
6-14
PARTS LIST
SECTION 7 PARTS LIST
SYMBOL
NUMBER
PART
NUMBER
DESCRIPTION
SYMBOL
NUMBER
IDC AUDIO CONTROL CARD
PART NO. 023-3039-280
C 001
C 002
C 003
C 004
C 005
C 006
C 007
C 008
C 009
C 010
C 011
C 012
C 013
C 014
C 015
C 016
C 017
C 018
C 019
C 020
C 021
C 022
C 023
C 024
C 025
C 026
C 027
C 028
C 029
C 030
C 031
C 032
C 033
C 034
C 035
C 036
C 037
C 038
C 039
C 040
C 041
.022 µF ±10% X7R 1210
.1 µF ±10% X7R 1210
.1 µF ±10% X7R 1210
.1 µF ±10% X7R 1210
.1 µF ±10% X7R 1210
.01 µF ±10% X7R chip
.01 µF ±10% X7R chip
.01 µF ±10% X7R chip
.01 µF ±10% X7R chip
.01 µF ±10% X7R chip
.01 µF ±10% X7R chip
.01 µF ±10% X7R chip
.01 µF ±10% X7R chip
.01 µF ±10% X7R chip
.01 µF ±10% X7R chip
.01 µF ±10% X7R chip
.01 µF ±10% X7R chip
.01 µF ±10% X7R chip
.01 µF ±10% X7R chip
.01 µF ±10% X7R chip
.01 µF ±10% X7R chip
.01 µF ±10% X7R chip
.01 µF ±10% X7R chip
.01 µF ±10% X7R chip
.1 µF ±10% X7R 1210
.1 µF ±10% X7R 1210
.1 µF ±10% X7R 1210
.1 µF ±10% X7R 1210
.1 µF ±10% X7R 1210
1 µF ±20% X7R 2225
.1 µF ±10% X7R 1210
.1 µF ±10% X7R 1210
.022 µF ±10% X7R 1210
.047 µF ±10% X7R 1210
.047 µF ±10% X7R 1210
.047 µF ±10% X7R 1210
.047 µF ±10% X7R 1210
.1 µF ±10% X7R 1210
.1 µF ±10% X7R 1210
.01 µF ±10% X7R chip
.1 µF ±10% X7R 1210
C 042
C 043
C 044
C 045
C 046
C 047
C 048
C 049
C 050
C 051
C 052
C 053
C 054
C 055
C 056
C 057
C 058
C 059
C 060
C 061
C 062
C 063
C 064
C 065
C 066
C 067
C 068
C 069
C 070
C 071
C 072
C 073
C 074
C 075
C 076
C 077
C 078
C 079
C 080
C 081
C 082
C 083
C 084
510-3607-223
510-3607-104
510-3607-104
510-3607-104
510-3607-104
510-3606-103
510-3606-103
510-3606-103
510-3606-103
510-3606-103
510-3606-103
510-3606-103
510-3606-103
510-3606-103
510-3606-103
510-3606-103
510-3606-103
510-3606-103
510-3606-103
510-3606-103
510-3606-103
510-3606-103
510-3606-103
510-3606-103
510-3607-104
510-3607-104
510-3607-104
510-3607-104
510-3607-104
510-3613-105
510-3607-104
510-3607-104
510-3607-223
510-3607-473
510-3607-473
510-3607-473
510-3607-473
510-3607-104
510-3607-104
510-3606-103
510-3607-104
7-1
PART
NUMBER
DESCRIPTION
.1 µF ±10% X7R 1210
2.2 µF 20V tantalum SMD
10 µF 63V axial low temp
10 µF 63V axial low temp
10 µF 63V axial low temp
10 µF 63V axial low temp
2.2 µF 20V tantalum SMD
2.2 µF 20V tantalum SMD
10 µF 63V axial low temp
10 µF 63V axial low temp
1000 µF 16V aluminum axial
1000 µF 16V aluminum axial
2.2 µF 20V tantalum SMD
2.2 µF 20V tantalum SMD
4.7 µF 10V tantalum SMD
10 µF 16V tantalum SMD
47 µF 25V electrolytic radial
47 µF 10V tantalum SMD
47 µF 25V electrolytic radial
47 µF 10V tantalum SMD
470 µF 40V axial low temp
6.8 µF 35V tantalum SMD
470 µF 40V axial low temp
6.8 µF 35V tantalum SMD
10 µF 63V axial low temp
10 µF 63V axial low temp
2.2 µF 20V tantalum SMD
2.2 µF 20V tantalum SMD
2.2 µF 20V tantalum SMD
2.2 µF 20V tantalum SMD
2.2 µF 20V tantalum SMD
2.2 µF 20V tantalum SMD
.1 µF ±10% X7R 1210
2.2 µF 20V tantalum SMD
47 µF 10V tantalum SMD
22 µF 16V tantalum SMD
.1 µF ±10% X7R 1210
15 µF 20V tantalum SMD
15 µF 20V tantalum SMD
15 µF 20V tantalum SMD
15 µF 20V tantalum SMD
15 µF 20V tantalum SMD
15 µF 20V tantalum SMD
510-3607-104
510-2626-229
510-4363-100
510-4363-100
510-4363-100
510-4363-100
510-2626-229
510-2626-229
510-4363-100
510-4363-100
510-4316-102
510-4316-102
510-2626-229
510-2626-229
510-2624-479
510-2625-100
510-4425-470
510-2624-470
510-4425-470
510-2624-470
510-4340-471
510-2628-689
510-4340-471
510-2628-689
510-4363-100
510-4363-100
510-2626-229
510-2626-229
510-2626-229
510-2626-229
510-2626-229
510-2626-229
510-3607-104
510-2626-229
510-2624-470
510-2625-220
510-3607-104
510-2626-150
510-2626-150
510-2626-150
510-2626-150
510-2626-150
510-2626-150
September 1995
Part No. 004-3039-272
PARTS LIST
SYMBOL
NUMBER
DESCRIPTION
PART
NUMBER
SYMBOL
NUMBER
CR001 Dual switch, common cathode 523-1504-022
EP001
EP002
EP003
EP004
EP005
EP006
EP007
EP008
EP009
EP010
EP011
EP012
Pin .025" sq x .655" long
Pin .025" sq x .655" long
Pin .025" sq x .655" long
Pin .025" sq x .655" long
Pin .025" sq x .655" long
Pin .025" sq x .655" long
Pin .025" sq x .655" long
Pin .025" sq x .655" long
Pin .025" sq x .655" long
Pin .025" sq x .655" long
Crystal pin insulator
Heatsink insulator TO-220
515-7101-205
515-7101-205
515-7101-205
515-7101-205
515-7101-205
515-7101-205
515-7101-205
515-7101-205
515-7101-205
515-7101-205
018-1080-001
574-5005-060
HW001
HW002
HW003
HW004
HW005
HW006
HW007
4-40 x .063 NPB nut
4-40 panhead philips ZPS
#4 x .046 shoulder washer
4-40 x .094 NPB nut
4-40 panhead philips ZPS
#4 shakeproof washer
Ni plated card bracket
560-2104-006
575-1604-010
596-4504-008
560-2104-008
575-1604-010
596-1104-008
537-9056-070
J 002
J 003
J 004
J 005
J 007
J 008
J 010
J 011
J 012
J 013
J 014
J 015
J 016
J 017
J 018
J 028
J 029
J 030
J 031
2-pin single inline header
2-pin single inline header
2-pin single inline header
2-pin single inline header
25-pin rt angle D-sub w/ins
2-pin single inline header
2-pin single inline header
2-pin single inline header
2-pin single inline header
2-pin single inline header
2-pin single inline header
2-pin single inline header
2-pin single inline header
2-pin single inline header
2-pin single inline header
2-pin single inline header
2-pin single inline header
2-pin single inline header
2-pin single inline header
515-7100-002
515-7100-002
515-7100-002
515-7100-002
515-0506-025
515-7100-002
515-7100-002
515-7100-002
515-7100-002
515-7100-002
515-7100-002
515-7100-002
515-7100-002
515-7100-002
515-7100-002
515-7100-002
515-7100-002
515-7100-002
515-7100-002
MP001 Heat sink TO-220
MP008 Stainless steel spacer
017-2221-034
317-7378-008
P 001 Shorting socket
515-5010-001
September 1995
Part No. 004-3039-272
P 002
P 003
P 004
P 005
P 006
P 007
P 008
P 009
P 010
P 011
P 012
P 013
P 014
P 015
P 016
P 017
P 018
7-2
DESCRIPTION
Shorting socket
Shorting socket
Shorting socket
Shorting socket
Shorting socket
Shorting socket
Shorting socket
Shorting socket
Shorting socket
Shorting socket
Shorting socket
Shorting socket
Shorting socket
Shorting socket
Shorting socket
Shorting socket
Shorting socket
PART
NUMBER
515-5010-001
515-5010-001
515-5010-001
515-5010-001
515-5010-001
515-5010-001
515-5010-001
515-5010-001
515-5010-001
515-5010-001
515-5010-001
515-5010-001
515-5010-001
515-5010-001
515-5010-001
515-5010-001
515-5010-001
PC001 PC board
035-3039-280
Q 001
Q 002
N-chnl E-MOSFET TO-92
N-chnl E-MOSFET TO-92
576-0006-108
576-0006-108
R 001
R 002
R 003
R 004
R 005
R 006
R 007
R 008
R 009
R 010
R 011
R 012
R 013
R 014
R 015
R 016
R 017
R 018
R 019
R 020
R 021
R 022
R 023
R 024
100k ohm multiturn pot
100k ohm multiturn pot
100k ohm multiturn pot
100k ohm multiturn pot
100k ohm multiturn pot
100k ohm multiturn pot
100k ohm multiturn pot
100k ohm multiturn pot
100k ohm multiturn pot
10k ohm ±5% 1206 SMD
10k ohm ±5% 1206 SMD
10k ohm ±5% 1206 SMD
10k ohm ±5% 1206 SMD
2.2k ohm ±5% 1206 SMD
100k ohm ±5% 1206 SMD
10k ohm ±5% 1206 SMD
100k ohm ±5% 1206 SMD
100k ohm ±5% 1206 SMD
2.2k ohm ±5% 1206 SMD
100k ohm ±5% 1206 SMD
100k ohm ±5% 1206 SMD
100k ohm ±5% 1206 SMD
100k ohm ±5% 1206 SMD
100k ohm ±5% 1206 SMD
562-0109-104
562-0109-104
562-0109-104
562-0109-104
562-0109-104
562-0109-104
562-0109-104
562-0109-104
562-0109-104
569-0115-103
569-0115-103
569-0115-103
569-0115-103
569-0115-222
569-0115-104
569-0115-103
569-0115-104
569-0115-104
569-0115-222
569-0115-104
569-0115-104
569-0115-104
569-0115-104
569-0115-104
PARTS LIST
SYMBOL
NUMBER
R 025
R 026
R 027
R 028
R 029
R 030
R 031
R 032
R 033
R 034
R 035
R 036
R 037
R 038
R 039
R 040
R 041
R 042
R 043
R 044
R 045
R 046
R 047
R 048
R 049
R 050
R 051
R 052
R 053
R 054
R 055
R 056
R 057
R 058
R 059
R 060
R 061
R 062
R 063
R 064
R 065
R 066
R 067
R 068
R 069
R 070
R 071
DESCRIPTION
270 ohm ±5% 1206 SMD
270 ohm ±5% 1206 SMD
10k ohm ±5% 1206 SMD
270 ohm ±5% 1206 SMD
620 ohm ±5% 1206 SMD
620 ohm ±5% 1206 SMD
100k ohm ±5% 1206 SMD
200k ohm ±5% 1206 SMD
100k ohm ±5% 1206 SMD
200k ohm ±5% 1206 SMD
100k ohm ±5% 1206 SMD
100k ohm ±5% 1206 SMD
200k ohm ±5% 1206 SMD
200k ohm ±5% 1206 SMD
100k ohm ±5% 1206 SMD
100k ohm ±5% 1206 SMD
2.2k ohm ±5% 1206 SMD
2.2k ohm ±5% 1206 SMD
270 ohm ±5% 1206 SMD
2.2k ohm ±5% 1206 SMD
2.2k ohm ±5% 1206 SMD
100k ohm ±5% 1206 SMD
100k ohm ±5% 1206 SMD
100k ohm ±5% 1206 SMD
2.2k ohm ±5% 1206 SMD
2.2k ohm ±5% 1206 SMD
220k ohm ±5% 1206 SMD
220k ohm ±5% 1206 SMD
2.2k ohm ±5% 1206 SMD
2.2k ohm ±5% 1206 SMD
20k ohm ±5% 1206 SMD
20k ohm ±5% 1206 SMD
20k ohm ±5% 1206 SMD
20k ohm ±5% 1206 SMD
2.2k ohm ±5% 1206 SMD
2.2k ohm ±5% 1206 SMD
220k ohm ±5% 1206 SMD
220k ohm ±5% 1206 SMD
220k ohm ±5% 1206 SMD
220k ohm ±5% 1206 SMD
10k ohm ±5% 1206 SMD
10k ohm ±5% 1206 SMD
22k ohm ±5% 1206 SMD
22k ohm ±5% 1206 SMD
300 ohm ±5% 1206 SMD
300 ohm ±5% 1206 SMD
10 ohm ±5% 1206 SMD
PART
NUMBER
SYMBOL
NUMBER
569-0115-271
569-0115-271
569-0115-103
569-0115-271
569-0115-621
569-0115-621
569-0115-104
569-0115-204
569-0115-104
569-0115-204
569-0115-104
569-0115-104
569-0115-204
569-0115-204
569-0115-104
569-0115-104
569-0115-222
569-0115-222
569-0115-271
569-0115-222
569-0115-222
569-0115-104
569-0115-104
569-0115-104
569-0115-222
569-0115-222
569-0115-224
569-0115-224
569-0115-222
569-0115-222
569-0115-203
569-0115-203
569-0115-203
569-0115-203
569-0115-222
569-0115-222
569-0115-224
569-0115-224
569-0115-224
569-0115-224
569-0115-103
569-0115-103
569-0115-223
569-0115-223
569-0115-301
569-0115-301
569-0115-100
R 072
R 073
R 074
R 075
R 076
R 077
R 078
R 079
R 080
R 081
R 082
R 083
R 084
R 085
R 086
R 087
R 088
R 089
R 090
R 091
R 092
R 093
R 094
R 095
R 096
R 097
R 098
R 099
R 100
R 101
R 102
R 103
R 104
R 105
R 106
R 109
R 110
R 111
7-3
PART
NUMBER
DESCRIPTION
100 ohm ±5% 1206 SMD
10 ohm ±5% 1206 SMD
100 ohm ±5% 1206 SMD
2.7 ohm ±5% 1206 SMD
2.7 ohm ±5% 1206 SMD
10k ohm ±5% 1206 SMD
10k ohm ±5% 1206 SMD
100k ohm ±5% 1206 SMD
2.2k ohm ±5% 1206 SMD
2.2k ohm ±5% 1206 SMD
100k ohm ±5% 1206 SMD
620 ohm ±5% 1206 SMD
200k ohm ±5% 1206 SMD
100k ohm ±5% 1206 SMD
200k ohm ±5% 1206 SMD
300 ohm ±5% 1206 SMD
620 ohm ±5% 1206 SMD
2.2k ohm ±5% 1206 SMD
3.9k ohm ±5% 1206 SMD
620 ohm ±5% 1206 SMD
10k ohm ±5% 1206 SMD
10k ohm ±5% 1206 SMD
10k ohm ±5% 1206 SMD
1k ohm ±5% 1206 SMD
1k ohm ±5% 1206 SMD
620 ohm ±5% 1206 SMD
10k ohm ±5% 1206 SMD
10k ohm ±5% 1206 SMD
100k ohm multiturn pot
100k ohm ±5% 1206 SMD
100k ohm ±5% 1206 SMD
2.2k ohm ±5% 1206 SMD
2.2k ohm ±5% 1206 SMD
12k ohm ±5% 1206 SMD
1.5M ohm ±5% 1206 SMD
100k ohm ±5% 1206 SMD
Zero ohm ±5% SMD 1206
Zero ohm ±5% SMD 1206
569-0115-101
569-0115-100
569-0115-101
569-0115-279
569-0115-279
569-0115-103
569-0115-103
569-0115-104
569-0115-222
569-0115-222
569-0115-104
569-0115-621
569-0115-204
569-0115-104
569-0115-204
569-0115-301
569-0115-621
569-0115-222
569-0115-392
569-0115-621
569-0115-103
569-0115-103
569-0115-103
569-0115-102
569-0115-102
569-0115-621
569-0115-103
569-0115-103
562-0109-104
569-0115-104
569-0115-104
569-0115-222
569-0115-222
569-0115-123
569-0115-155
569-0115-104
569-0115-104
569-0115-104
RN001 22k ohm 9-res 10-pin SIP
RN002 22k ohm 9-res 10-pin SIP
569-6000-009
569-6000-009
S 001
S 002
8-position dip switch
8-position dip switch
583-5002-008
583-5002-008
U 001
U 002
Quad 2-input NAND 74HC00 544-3766-000
8-bit eqalzr/compartr SOIC
544-3766-688
September 1995
Part No. 004-3039-272
PARTS LIST
SYMBOL
NUMBER
U 003
U 004
U 005
U 006
U 007
U 008
U 009
U 010
U 011
U 012
U 013
U 014
U 015
U 016
U 017
U 018
U 019
U 021
U 022
U 027
U 028
U 029
DESCRIPTION
PART
NUMBER
SYMBOL
NUMBER
8-bit eqalzr/compartr SOIC
544-3766-688
1 of 16 demux SOIC 74HC154 544-3766-154
D flip-flop SOIC 74HC574
544-3766-574
D flip-flop SOIC 74HC574
544-3766-574
DTMF gen binary in 74HC165 544-4005-007
Bilateral switch SOIC 4066B 544-3016-066
Quad op amp SOIC 3403
544-2020-008
Quad op amp SOIC 3403
544-2020-008
Quad op amp SOIC 3403
544-2020-008
Quad op amp SOIC 3403
544-2020-008
10W audio pentawatt 74HC574 544-2006-013
10W audio pentawatt 74HC574 544-2006-013
Digital 100k ohm pot X9104 544-0004-202
Digital 100k ohm pot X9104 544-0004-202
Digital 100k ohm pot X9104 544-0004-202
Quad op amp SOIC 3403
544-2020-008
Quad op amp SOIC 3403
544-2020-008
Xparent latch SOIC 74HC573 544-3766-573
Bilateral switch SOIC 4066B 544-3016-066
RS232C/V.28 driver/receiver 544-2023-014
D flip-flop SOIC 74HC574
544-3766-574
Monostable multivbrtr SO-16 544-3766-123
Y 001 3.5795 MHz crystal
521-0003-579
Z 001 EMI suppression filter
Z 002 EMI suppression filter
Z 003 EMI suppression filter
532-3003-002
532-3003-002
532-3003-002
510-4325-102
DS005 T-1.75 wedge base lamp
583-4020-003
HW001 8-32 x .125 CPS nut
HW002 8 x .02 lock washer int CPS
HW003 8 x .32 flat washer NPB
HW004 Foam speaker gasket
HW005 Button
HW006 #4 shakeproof washer
HW007 6 x .028 flat washer NPB
HW008 4-40 panhead ZPS philips
HW009 4-40 panhead ZPS philips
560-1108-011
596-1108-011
596-2408-012
018-1126-001
583-4020-002
596-1104-008
596-2406-010
575-1604-008
575-1604-012
LS001 5" 15W 3.2 ohm spkr w/cloth
589-1016-002
September 1995
Part No. 004-3039-272
PART
NUMBER
MP001 Speaker console panel
MP002 1/4" cable clamp
017-2222-241
572-0001-003
PC001 PC board
035-3039-260
R 001
R 002
3.3 ohm ±10% 5W WW
3.3 ohm ±10% 5W WW
T 001
Wall transformer
S 005
Lighted push-push switch
W 017 Speaker wire w/tini plug
W 021 Speaker wire w/tini plug
569-2006-339
569-2006-339
563-001-005
583-4020-001
597-2006-100
597-2006-100
PCM SUMMATION BOARD
PART NO. 023-3039-780
C 00151 pF ±5% NPO 1206 chip510-3602-510
C 00251 pF ±5% NPO 1206 chip510-3602-510
C 0032200 pF ±5% NPO 1206 chip510-3602-222
C 0042200 pF ±5% NPO 1206 chip510-3602-222
C 005.001 µF ±5% NPO 1206 chip510-3602-102
C 006.001 µF ±5% NPO 1206 chip510-3602-102
C 007.1 µF ±5% X7R 1206510-3609-104
C 008.01 µF ±10% X7R chip510-3606-103
C 009.01 µF ±10% X7R chip510-3606-103
C 010.01 µF ±10% X7R chip510-3606-103
C 011.01 µF ±10% X7R chip510-3606-103
C 012.01 µF ±10% X7R chip510-3606-103
C 013.01 µF ±10% X7R chip510-3606-103
C 014.01 µF ±10% X7R chip510-3606-103
C 015.01 µF ±10% X7R chip510-3606-103
C 016.01 µF ±10% X7R chip510-3606-103
C 017.01 µF ±10% X7R chip510-3606-103
C 018.01 µF ±10% X7R chip510-3606-103
C 019.01 µF ±10% X7R chip510-3606-103
C 020.01 µF ±10% X7R chip510-3606-103
C 023.01 µF ±10% X7R chip510-3606-103
C 024.01 µF ±10% X7R chip510-3606-103
C 025.01 µF ±10% X7R chip510-3606-103
C 026.01 µF ±10% X7R chip510-3606-103
C 027.01 µF ±10% X7R chip510-3606-103
C 029.01 µF ±10% X7R chip510-3606-103
C 030.01 µF ±10% X7R chip510-3606-103
C 032.01 µF ±10% X7R chip510-3606-103
C 033.01 µF ±10% X7R chip510-3606-103
SPEAKER CONSOLE PANEL
PART NO. 023-3039-260
C 001 1000 µF 16V aluminum axial
DESCRIPTION
7-4
PARTS LIST
SYMBOL
NUMBER
DESCRIPTION
PART
NUMBER
SYMBOL
NUMBER
U 001
U 002
U 003
U 004
U 005
U 006
U 007
U 008
U 009
U 010
U 011
U 012
U 013
U 014
U 015
U 016
U 017
U 018
U 019
U 020
C 034
C 035
C 036
C 037
10 µF 16V tantalum SMD
10 µF 16V tantalum SMD
10 µF 16V tantalum SMD
10 µF 16V tantalum SMD
510-2625-100
510-2625-100
510-2625-100
510-2625-100
EP001
EP002
EP003
EP004
Pin .025" sq x .655" long
Pin .025" sq x .655" long
Pin .025" sq x .655" long
Pin .025" sq x .655" long
515-7101-205
515-7101-205
515-7101-205
515-7101-205
HW001 4-40 panhead philips ZPS
HW002 #4 shakeproof washer
HW003 4-40 x .063 nut NPB
575-1604-008
596-1104-008
560-2104-006
J 001
J 003
J 004
515-5012-011
515-9031-007
515-9031-008
11-pos receptacle SIP
2-pin rt angle PC mt conntr
3-pin rt angle PC mt conntr
MP001 PC board spacer
115-0260-011
P 001 11-pin single row header
515-9031-481
R 001
R 002
R 003
R 004
R 005
R 006
R 007
R 008
R 009
R 010
R 011
R 012
R 013
R 014
R 015
R 016
R 017
R 018
R 019
R 020
R 021
R 022
R 023
R 024
R 025
562-0109-104
569-0115-272
569-0115-272
569-0115-433
569-0115-433
569-0115-183
569-0115-183
569-0115-102
569-0115-302
569-0115-682
569-0115-153
569-0115-303
569-0115-623
569-0115-124
569-0115-244
569-0115-511
569-0115-754
569-0115-103
569-0115-103
569-0115-103
569-0115-301
569-0115-301
569-0111-368
569-0111-409
562-0109-104
PART
NUMBER
DESCRIPTION
8 channel mux/demux
544-3016-051
Hex inverter SOIC 74HC04 544-3766-004
Quad 2-in AND SOIC HC08 544-3766-008
Preset counter SOIC 74HC163 544-3766-163
Shift register SO-14 74HC164 544-3766-164
8-bit shift register 74HC165 544-3766-165
8-bit shift register 74HC165 544-3766-165
8-bit shift register 74HC165 544-3766-165
8-bit shift register 74HC165 544-3766-165
D flip flop SOIC 74HC574
544-3766-574
D flip flop SOIC 74HC574
544-3766-574
D flip flop SOIC 74HC574
544-3766-574
D flip flop SOIC 74HC574
544-3766-574
D flip flop SOIC 74HC574
544-3766-574
D flip flop SOIC 74HC574
544-3766-574
D/A convertr DIP-18 DAC88 544-2034-002
-5V voltage regulator LM320T 544-2003-034
Quad op amp 3403
544-2020-008
JFET op amp SOIC
544-2020-016
16-pin Tx/Rx filter PC mt
544-2038-003
W 001 11-cond flex cable 6.5" long
100k ohm multiturn pot
2.7k ohm ±5% 1206 SMD
2.7k ohm ±5% 1206 SMD
43k ohm ±5% 1206 SMD
43k ohm ±5% 1206 SMD
18k ohm ±5% 1206 SMD
18k ohm ±5% 1206 SMD
1k ohm ±5% 1206 SMD
3k ohm ±5% 1206 SMD
6.8k ohm ±5% 1206 SMD
15k ohm ±5% 1206 SMD
30k ohm ±5% 1206 SMD
62k ohm ±5% 1206 SMD
120k ohm ±5% 1206 SMD
240k ohm ±5% 1206 SMD
510 ohm ±5% 1206 SMD
750k ohm ±5% 1206 SMD
10k ohm ±5% 1206 SMD
10k ohm ±5% 1206 SMD
10k ohm ±5% 1206 SMD
300 ohm ±5% 1206 SMD
300 ohm ±5% 1206 SMD
4.99k ohm ±1% 1206 SMD
12.1k ohm ±1% 1206 SMD
100k ohm multiturn pot
597-0016-013
911 INTERFACE MODULE
PART NO. 023-3039-900
C 001
C 002
C 003
C 004
C 005
C 006
C 007
C 008
C 009
C 010
C 011
C 012
C 013
C 014
C 015
C 016
C 017
C 018
C 019
C 020
C 021
7-5
.01 µF ±10% X7R 0805 chip
.01 µF ±10% X7R 0805 chip
.01 µF ±10% X7R 0805 chip
.01 µF ±10% X7R 0805 chip
.01 µF ±10% X7R 0805 chip
2.2 µF 20V tantalum SMD
.01 µF ±10% X7R 0805 chip
47 µF 10V tantalum SMD
47 µF 10V tantalum SMD
.01 µF ±10% X7R 0805 chip
47 µF 10V tantalum SMD
.01 µF ±10% X7R 0805 chip
.01 µF ±10% X7R 0805 chip
10 µF 16V tantalum SMD
4.7 µF 10V tantalum SMD
.1 µF ±10% X7R 1210
.1 µF ±10% X7R 1210
2.2 µF 20V tantalum SMD
10 µF 16V tantalum SMD
4.7 µF 10V tantalum SMD
.1 µF ±10% X7R 1210
510-3605-103
510-3605-103
510-3605-103
510-3605-103
510-3605-103
510-2626-229
510-3605-103
510-2624-470
510-2624-470
510-3605-103
510-2624-470
510-3605-103
510-3605-103
510-2625-100
510-2624-479
510-3607-104
510-3607-104
510-2626-229
510-2625-100
510-2624-479
510-3607-104
September 1995
Part No. 004-3039-272
PARTS LIST
SYMBOL
NUMBER
C 022
C 023
C 024
C 025
C 026
C 027
C 028
C 031
C 032
C 033
C 034
C 035
C 036
C 037
C 038
C 039
C 040
C 041
C 042
C 043
C 044
C 045
C 046
C 047
C 048
C 049
C 050
C 051
C 052
C 053
C 054
C 055
C 056
C 057
C 058
C 059
C 060
C 061
C 062
C 063
C 064
C 065
C 066
C 067
C 068
C 069
C 070
DESCRIPTION
.1 µF ±10% X7R 1210
2.2 µF 20V tantalum SMD
10 µF 16V tantalum SMD
4.7 µF 10V tantalum SMD
.1 µF ±10% X7R 1210
.1 µF ±10% X7R 1210
2.2 µF 20V tantalum SMD
.1 µF ±10% X7R 1210
.1 µF ±10% X7R 1210
2.2 µF 20V tantalum SMD
10 µF 16V tantalum SMD
4.7 µF 10V tantalum SMD
.1 µF ±10% X7R 1210
.1 µF ±10% X7R 1210
2.2 µF 20V tantalum SMD
10 µF 16V tantalum SMD
4.7 µF 10V tantalum SMD
.1 µF ±10% X7R 1210
.1 µF ±10% X7R 1210
2.2 µF 20V tantalum SMD
10 µF 16V tantalum SMD
4.7 µF 10V tantalum SMD
.1 µF ±10% X7R 1210
.1 µF ±10% X7R 1210
2.2 µF 20V tantalum SMD
2.2 µF 20V tantalum SMD
2.2 µF 20V tantalum SMD
2.2 µF 20V tantalum SMD
2.2 µF 20V tantalum SMD
2.2 µF 20V tantalum SMD
2.2 µF 20V tantalum SMD
2.2 µF 20V tantalum SMD
2.2 µF 20V tantalum SMD
2.2 µF 20V tantalum SMD
2.2 µF 20V tantalum SMD
2.2 µF 20V tantalum SMD
2.2 µF 20V tantalum SMD
2.2 µF 20V tantalum SMD
2.2 µF 20V tantalum SMD
2.2 µF 20V tantalum SMD
2.2 µF 20V tantalum SMD
2.2 µF 20V tantalum SMD
2.2 µF 20V tantalum SMD
2.2 µF 20V tantalum SMD
2.2 µF 20V tantalum SMD
2.2 µF 20V tantalum SMD
2.2 µF 20V tantalum SMD
September 1995
Part No. 004-3039-272
PART
NUMBER
SYMBOL
NUMBER
510-3607-104
510-2626-229
510-2625-100
510-2624-479
510-3607-104
510-3607-104
510-2626-229
510-3607-104
510-3607-104
510-2626-229
510-2625-100
510-2624-479
510-3607-104
510-3607-104
510-2626-229
510-2625-100
510-2624-479
510-3607-104
510-3607-104
510-2626-229
510-2625-100
510-2624-479
510-3607-104
510-3607-104
510-2626-229
510-2626-229
510-2626-229
510-2626-229
510-2626-229
510-2626-229
510-2626-229
510-2626-229
510-2626-229
510-2626-229
510-2626-229
510-2626-229
510-2626-229
510-2626-229
510-2626-229
510-2626-229
510-2626-229
510-2626-229
510-2626-229
510-2626-229
510-2626-229
510-2626-229
510-2626-229
C 071
C 072
C 073
C 074
C 075
C 076
C 077
C 078
C 079
C 080
C 081
C 082
C 083
C 084
C 085
C 086
C 090
C 091
C 092
C 093
C 094
C 096
C 097
C 099
2.2 µF 20V tantalum SMD
2.2 µF 20V tantalum SMD
2.2 µF 20V tantalum SMD
2.2 µF 20V tantalum SMD
2.2 µF 20V tantalum SMD
2.2 µF 20V tantalum SMD
2.2 µF 20V tantalum SMD
2.2 µF 20V tantalum SMD
2.2 µF 20V tantalum SMD
1000 µF 16V aluminum axial
10 µF 16V tantalum SMD
.047 µF ±10% X7R chip
10 µF 63V axial low temp
10 µF 63V axial low temp
10 µF 63V axial low temp
10 µF 63V axial low temp
10 µF 16V tantalum SMD
4.7 µF 10V tantalum SMD
.1 µF ±10% X7R 1210
.1 µF ±10% X7R 1210
2.2 µF 20V tantalum SMD
2.2 µF 20V tantalum SMD
2.2 µF 20V tantalum SMD
47 µF 10V tantalum SMD
510-2626-229
510-2626-229
510-2626-229
510-2626-229
510-2626-229
510-2626-229
510-2626-229
510-2626-229
510-2626-229
510-4316-102
510-2625-100
510-3606-473
510-4363-100
510-4363-100
510-4363-100
510-4363-100
510-2625-100
510-2624-479
510-3607-104
510-3607-104
510-2626-229
510-2626-229
510-2626-229
510-2624-470
CR001
CR002
CR003
CR004
CR005
CR006
CR007
Switching diode SOT-23
Switching diode SOT-23
Switching diode SOT-23
Switching diode SOT-23
Switching diode SOT-23
Switching diode SOT-23
Switching diode SOT-23
523-1504-002
523-1504-002
523-1504-002
523-1504-002
523-1504-002
523-1504-002
523-1504-002
7-6
DESCRIPTION
PART
NUMBER
EP001 2-pos shorting socket
EP002 Heat sink insulator TO-220
515-5010-001
574-5005-060
HW001
HW001
HW002
HW003
HW004
4-40 machine panhead ZPS
4-40 machine panhead XPS
#4 shakeproof washer
4-40 x 0.063 nut NPB
Flexible grommet
575-1604-010
575-1604-008
596-1104-008
560-2104-006
574-0001-025
J 001
J 004
J 005
J 008
J 009
25-pin right angle D-submin
3.6mm encl jack (supvr mic)
3.6mm encl jack (bkgnd spkr)
26-pin mini-terminal block
26-pin mini-terminal block
515-0506-025
515-2001-011
515-2001-011
515-7110-426
515-7110-426
PARTS LIST
SYMBOL
NUMBER
J 013
J 014
J 015
J 016
J 017
J 018
J 019
J 020
J 021
J 022
J 023
J 024
J 026
J 027
J 028
J 029
J 031
J 032
J 033
J 034
J 036
J 037
J 038
J 039
J 041
J 042
J 043
J 044
J 046
J 047
J 048
J 049
J 051
J 052
J 056
J 057
J 061
J 062
J 063
J 064
J 065
J 066
J 067
J 068
J 069
J 070
J 080
DESCRIPTION
3-pin single inline header
3-pin single inline header
3-pin single inline header
3-pin single inline header
3-pin single inline header
3-pin single inline header
3-pin single inline header
6-pin double row header
3-pin single inline header
3-pin single inline header
3-pin single inline header
2-pin single inline header
3-pin single inline header
3-pin single inline header
3-pin single inline header
2-pin single inline header
3-pin single inline header
3-pin single inline header
3-pin single inline header
2-pin single inline header
3-pin single inline header
3-pin single inline header
3-pin single inline header
2-pin single inline header
3-pin single inline header
3-pin single inline header
3-pin single inline header
2-pin single inline header
3-pin single inline header
3-pin single inline header
3-pin single inline header
2-pin single inline header
6-pin double row header
6-pin double row header
6-pin double row header
6-pin double row header
6-pin double row header
6-pin double row header
6-pin double row header
6-pin double row header
6-pin double row header
6-pin double row header
6-pin double row header
6-pin double row header
6-pin double row header
6-pin double row header
3-pin single inline header
PART
NUMBER
SYMBOL
NUMBER
515-7100-003
515-7100-003
515-7100-003
515-7100-003
515-7100-003
515-7100-003
515-7100-003
515-7100-506
515-7100-003
515-7100-003
515-7100-003
515-7100-002
515-7100-003
515-7100-003
515-7100-003
515-7100-002
515-7100-003
515-7100-003
515-7100-003
515-7100-002
515-7100-003
515-7100-003
515-7100-003
515-7100-002
515-7100-003
515-7100-003
515-7100-003
515-7100-002
515-7100-003
515-7100-003
515-7100-003
515-7100-002
515-7100-506
515-7100-506
515-7100-506
515-7100-506
515-7100-506
515-7100-506
515-7100-506
515-7100-506
515-7100-506
515-7100-506
515-7100-506
515-7100-506
515-7100-506
515-7100-506
515-7100-003
J 081
J 082
J 083
J 099
3-pin single inline header
3-pin single inline header
2-pin single inline header
2-pin single inline header
515-7100-003
515-7100-003
515-7100-002
515-7100-002
MP001
MP002
MP003
MP004
MP005
Heatsink TO-220 solder tab
Interface board cover
Min support post
Rack panel interface
3/16 hex 4-40 shoulder spacer
539-0009-100
018-1007-200
574-5010-005
017-2210-200
013-1139-018
P 001
P 002
9-pos right angle D-submin
515-0506-042
16-pos right angle shrd header 515-7104-108
7-7
PART
NUMBER
DESCRIPTION
PC000 PC board
035-3039-900
Q 001
Q 002
Si NPN SOT-23
Si NPN SOT-23
576-0003-658
576-0003-658
R 001
R 002
R 003
R 004
R 005
R 006
R 007
R 008
R 009
R 010
R 011
R 012
R 013
R 014
R 015
R 016
R 017
R 018
R 019
R 020
R 021
R 022
R 023
R 024
R 025
R 026
R 027
R 028
500k ohm multiturn pot
500k ohm multiturn pot
500k ohm multiturn pot
100k ohm trim pot
100k ohm trim pot
100k ohm trim pot
100k ohm trim pot
500k ohm multiturn pot
500k ohm multiturn pot
100k ohm trim pot
100k ohm trim pot
100k ohm trim pot
100k ohm trim pot
100k ohm trim pot
100k ohm trim pot
10k ohm ±5% 0805 chip
10k ohm ±5% 0805 chip
10k ohm ±5% 0805 chip
10k ohm ±5% 0805 chip
10k ohm ±5% 0805 chip
10k ohm ±5% 0805 chip
10k ohm ±5% 0805 chip
10k ohm ±5% 0805 chip
10k ohm ±5% 0805 chip
10k ohm ±5% 0805 chip
10k ohm ±5% 0805 chip
10k ohm ±5% 0805 chip
10k ohm ±5% 0805 chip
562-0110-504
562-0110-504
562-0110-504
562-0110-104
562-0110-104
562-0110-104
562-0110-104
562-0110-504
562-0110-504
562-0110-104
562-0110-104
562-0110-104
562-0110-104
562-0110-104
562-0110-104
569-0105-103
569-0105-103
569-0105-103
569-0105-103
569-0105-103
569-0105-103
569-0105-103
569-0105-103
569-0105-103
569-0105-103
569-0105-103
569-0105-103
569-0105-103
September 1995
Part No. 004-3039-272
PARTS LIST
SYMBOL
NUMBER
R 029
R 030
R 031
R 032
R 033
R 034
R 035
R 036
R 037
R 038
R 039
R 040
R 041
R 042
R 043
R 044
R 045
R 046
R 047
R 048
R 049
R 050
R 051
R 052
R 053
R 054
R 055
R 056
R 057
R 058
R 059
R 060
R 061
R 062
R 063
R 064
R 065
R 066
R 067
R 068
R 069
R 070
R 071
R 077
R 078
R 079
R 080
DESCRIPTION
10k ohm ±5% 0805 chip
300 ohm ±5% 0805 chip
620 ohm ±5% 0805 chip
620 ohm ±5% 0805 chip
2.2k ohm ±5% 0805 chip
3.9k ohm ±5% 0805 chip
120 ohm ±5% 0805 chip
620 ohm ±5% 0805 chip
910 ohm ±5% 0805 chip
100k ohm ±5% 0805 chip
100k ohm ±5% 0805 chip
100k ohm ±5% 0805 chip
100k ohm ±5% 0805 chip
2.2k ohm ±5% 0805 chip
2.2k ohm ±5% 0805 chip
300 ohm ±5% 0805 chip
620 ohm ±5% 0805 chip
620 ohm ±5% 0805 chip
2.2k ohm ±5% 0805 chip
3.9k ohm ±5% 0805 chip
120 ohm ±5% 0805 chip
620 ohm ±5% 0805 chip
910 ohm ±5% 0805 chip
100k ohm ±5% 0805 chip
100k ohm ±5% 0805 chip
100k ohm ±5% 0805 chip
100k ohm ±5% 0805 chip
2.2k ohm ±5% 0805 chip
2.2k ohm ±5% 0805 chip
300 ohm ±5% 0805 chip
620 ohm ±5% 0805 chip
620 ohm ±5% 0805 chip
2.2k ohm ±5% 0805 chip
3.9k ohm ±5% 0805 chip
120 ohm ±5% 0805 chip
620 ohm ±5% 0805 chip
910 ohm ±5% 0805 chip
100k ohm ±5% 0805 chip
100k ohm ±5% 0805 chip
100k ohm ±5% 0805 chip
100k ohm ±5% 0805 chip
2.2k ohm ±5% 0805 chip
2.2k ohm ±5% 0805 chip
120 ohm ±5% 0805 chip
620 ohm ±5% 0805 chip
910 ohm ±5% 0805 chip
100k ohm ±5% 0805 chip
September 1995
Part No. 004-3039-272
PART
NUMBER
SYMBOL
NUMBER
569-0105-103
569-0105-301
569-0105-621
569-0105-621
569-0105-222
569-0105-392
569-0105-121
569-0105-621
569-0105-911
569-0105-104
569-0105-104
569-0105-104
569-0105-104
569-0105-222
569-0105-222
569-0105-301
569-0105-621
569-0105-621
569-0105-222
569-0105-392
569-0105-121
569-0105-621
569-0105-911
569-0105-104
569-0105-104
569-0105-104
569-0105-104
569-0105-222
569-0105-222
569-0105-301
569-0105-621
569-0105-621
569-0105-222
569-0105-392
569-0105-121
569-0105-621
569-0105-911
569-0105-104
569-0105-104
569-0105-104
569-0105-104
569-0105-222
569-0105-222
569-0105-121
569-0105-621
569-0105-911
569-0105-104
R 081
R 082
R 083
R 084
R 085
R 086
R 087
R 088
R 089
R 090
R 091
R 092
R 093
R 094
R 095
R 096
R 097
R 098
R 099
R 100
R 101
R 102
R 103
R 104
R 105
R 106
R 107
R 108
R 109
R 110
R 111
R 112
R 113
R 114
R 115
R 116
R 117
R 118
R 119
R 120
R 121
R 122
R 123
R 124
R 125
R 126
R 127
7-8
DESCRIPTION
100k ohm ±5% 0805 chip
100k ohm ±5% 0805 chip
100k ohm ±5% 0805 chip
2.2k ohm ±5% 0805 chip
2.2k ohm ±5% 0805 chip
300 ohm ±5% 0805 chip
620 ohm ±5% 0805 chip
620 ohm ±5% 0805 chip
2.2k ohm ±5% 0805 chip
3.9k ohm ±5% 0805 chip
120 ohm ±5% 0805 chip
620 ohm ±5% 0805 chip
910 ohm ±5% 0805 chip
100k ohm ±5% 0805 chip
100k ohm ±5% 0805 chip
47k ohm ±5% 0805 chip
47k ohm ±5% 0805 chip
2.2k ohm ±5% 0805 chip
2.2k ohm ±5% 0805 chip
300 ohm ±5% 0805 chip
620 ohm ±5% 0805 chip
620 ohm ±5% 0805 chip
2.2k ohm ±5% 0805 chip
3.9k ohm ±5% 0805 chip
120 ohm ±5% 0805 chip
620 ohm ±5% 0805 chip
910 ohm ±5% 0805 chip
100k ohm ±5% 0805 chip
100k ohm ±5% 0805 chip
100k ohm ±5% 0805 chip
100k ohm ±5% 0805 chip
2.2k ohm ±5% 0805 chip
2.2k ohm ±5% 0805 chip
300 ohm ±5% 0805 chip
620 ohm ±5% 0805 chip
620 ohm ±5% 0805 chip
2.2k ohm ±5% 0805 chip
3.9k ohm ±5% 0805 chip
120 ohm ±5% 0805 chip
620 ohm ±5% 0805 chip
910 ohm ±5% 0805 chip
100k ohm ±5% 0805 chip
100k ohm ±5% 0805 chip
100k ohm ±5% 0805 chip
100k ohm ±5% 0805 chip
2.2k ohm ±5% 0805 chip
2.2k ohm ±5% 0805 chip
PART
NUMBER
569-0105-104
569-0105-104
569-0105-104
569-0105-222
569-0105-222
569-0105-301
569-0105-621
569-0105-621
569-0105-222
569-0105-392
569-0105-121
569-0105-621
569-0105-911
569-0105-104
569-0105-104
569-0105-473
569-0105-473
569-0105-222
569-0105-222
569-0105-301
569-0105-621
569-0105-621
569-0105-222
569-0105-392
569-0105-121
569-0105-621
569-0105-911
569-0105-104
569-0105-104
569-0105-104
569-0105-104
569-0105-222
569-0105-222
569-0105-301
569-0105-621
569-0105-621
569-0105-222
569-0105-392
569-0105-121
569-0105-621
569-0105-911
569-0105-104
569-0105-104
569-0105-104
569-0105-104
569-0105-222
569-0105-222
PARTS LIST
SYMBOL
NUMBER
R 128
R 129
R 130
R 131
R 132
R 133
R 134
R 135
R 136
R 137
R 138
R 139
R 140
R 141
R 142
R 143
R 144
R 145
R 146
R 147
R 148
R 149
R 150
R 151
R 152
R 153
R 154
R 155
R 156
R 157
R 158
R 159
R 160
R 161
R 162
R 163
R 164
R 165
R 166
R 167
R 168
R 169
R 170
R 171
R 172
R 173
R 174
DESCRIPTION
10k ohm ±5% 0805 chip
10k ohm ±5% 0805 chip
10k ohm ±5% 0805 chip
3.9k ohm ±5% 0805 chip
3.9k ohm ±5% 0805 chip
9.1k ohm ±5% 0805 chip
100k ohm ±5% 0805 chip
100k ohm ±5% 0805 chip
100k ohm ±5% 0805 chip
100k ohm ±5% 0805 chip
100k ohm ±5% 0805 chip
51k ohm ±5% 0805 chip
51k ohm ±5% 0805 chip
2.2k ohm ±5% 0805 chip
100k ohm ±5% 0805 chip
100k ohm ±5% 0805 chip
68 ohm ±5% 0805 chip
300 ohm ±5% 0805 chip
430 ohm ±5% 0805 chip
430 ohm ±5% 0805 chip
300 ohm ±5% 0805 chip
68 ohm ±5% 0805 chip
51k ohm ±5% 0805 chip
51k ohm ±5% 0805 chip
2.2k ohm ±5% 0805 chip
100k ohm ±5% 0805 chip
100k ohm ±5% 0805 chip
68 ohm ±5% 0805 chip
300 ohm ±5% 0805 chip
430 ohm ±5% 0805 chip
430 ohm ±5% 0805 chip
300 ohm ±5% 0805 chip
68 ohm ±5% 0805 chip
2.2k ohm ±5% 0805 chip
2.2k ohm ±5% 0805 chip
100k ohm ±5% 0805 chip
100k ohm ±5% 0805 chip
68 ohm ±5% 0805 chip
300 ohm ±5% 0805 chip
430 ohm ±5% 0805 chip
430 ohm ±5% 0805 chip
300 ohm ±5% 0805 chip
68 ohm ±5% 0805 chip
2.2k ohm ±5% 0805 chip
2.2k ohm ±5% 0805 chip
100k ohm ±5% 0805 chip
100k ohm ±5% 0805 chip
PART
NUMBER
SYMBOL
NUMBER
569-0105-103
569-0105-103
569-0105-103
569-0105-392
569-0105-392
569-0105-912
569-0105-104
569-0105-104
569-0105-104
569-0105-104
569-0105-104
569-0105-513
569-0105-513
569-0105-222
569-0105-104
569-0105-104
569-0105-680
569-0105-301
569-0105-431
569-0105-431
569-0105-301
569-0105-680
569-0105-513
569-0105-513
569-0105-222
569-0105-104
569-0105-104
569-0105-680
569-0105-301
569-0105-431
569-0105-431
569-0105-301
569-0105-680
569-0105-222
569-0105-222
569-0105-104
569-0105-104
569-0105-680
569-0105-301
569-0105-431
569-0105-431
569-0105-301
569-0105-680
569-0105-222
569-0105-222
569-0105-104
569-0105-104
R 175
R 176
R 177
R 178
R 179
R 180
R 181
R 182
R 183
R 184
R 185
R 186
R 187
R 188
R 189
R 190
R 191
R 192
R 193
R 194
R 195
R 196
R 197
R 198
R 199
R 200
R 201
R 202
R 203
R 204
R 205
R 206
R 207
R 208
R 209
R 210
R 211
R 212
R 213
R 214
R 215
R 216
R 217
R 218
R 219
R 220
R 221
7-9
PART
NUMBER
DESCRIPTION
68 ohm ±5% 0805 chip
300 ohm ±5% 0805 chip
430 ohm ±5% 0805 chip
430 ohm ±5% 0805 chip
300 ohm ±5% 0805 chip
68 ohm ±5% 0805 chip
2.2k ohm ±5% 0805 chip
2.2k ohm ±5% 0805 chip
100k ohm ±5% 0805 chip
100k ohm ±5% 0805 chip
68 ohm ±5% 0805 chip
300 ohm ±5% 0805 chip
430 ohm ±5% 0805 chip
430 ohm ±5% 0805 chip
300 ohm ±5% 0805 chip
68 ohm ±5% 0805 chip
2.2k ohm ±5% 0805 chip
2.2k ohm ±5% 0805 chip
100k ohm ±5% 0805 chip
100k ohm ±5% 0805 chip
68 ohm ±5% 0805 chip
300 ohm ±5% 0805 chip
430 ohm ±5% 0805 chip
430 ohm ±5% 0805 chip
300 ohm ±5% 0805 chip
68 ohm ±5% 0805 chip
2.2k ohm ±5% 0805 chip
2.2k ohm ±5% 0805 chip
100k ohm ±5% 0805 chip
100k ohm ±5% 0805 chip
68 ohm ±5% 0805 chip
300 ohm ±5% 0805 chip
430 ohm ±5% 0805 chip
430 ohm ±5% 0805 chip
300 ohm ±5% 0805 chip
68 ohm ±5% 0805 chip
2.2k ohm ±5% 0805 chip
2.2k ohm ±5% 0805 chip
10k ohm ±5% 0805 chip
10k ohm ±5% 0805 chip
100k ohm ±5% 0805 chip
100k ohm ±5% 0805 chip
100k ohm ±5% 0805 chip
100k ohm ±5% 0805 chip
100k ohm ±5% 0805 chip
100k ohm ±5% 0805 chip
100k ohm ±5% 0805 chip
569-0105-680
569-0105-301
569-0105-431
569-0105-431
569-0105-301
569-0105-680
569-0105-222
569-0105-222
569-0105-104
569-0105-104
569-0105-680
569-0105-301
569-0105-431
569-0105-431
569-0105-301
569-0105-680
569-0105-222
569-0105-222
569-0105-104
569-0105-104
569-0105-680
569-0105-301
569-0105-431
569-0105-431
569-0105-301
569-0105-680
569-0105-222
569-0105-222
569-0105-104
569-0105-104
569-0105-680
569-0105-301
569-0105-431
569-0105-431
569-0105-301
569-0105-680
569-0105-222
569-0105-222
569-0105-103
569-0105-103
569-0105-104
569-0105-104
569-0105-104
569-0105-104
569-0105-104
569-0105-104
569-0105-104
September 1995
Part No. 004-3039-272
PARTS LIST
SYMBOL
NUMBER
R 222
R 223
R 224
R 225
R 227
R 230
R 231
R 232
R 233
R 234
R 235
R 236
R 237
R 238
R 239
R 240
R 241
R 242
R 243
R 250
R 251
R 252
R 255
R 256
R 257
R 300
R 301
R 302
R 303
R 304
R 305
R 306
DESCRIPTION
10k ohm ±5% 0805 chip
100 ohm ±5% 0805 chip
10 ohm ±5% 0805 chip
2.7 ohm ±5% 0805 chip
10k ohm ±5% 0805 chip
300 ohm ±5% 0805 chip
620 ohm ±5% 0805 chip
620 ohm ±5% 0805 chip
2.2k ohm ±5% 0805 chip
3.9k ohm ±5% 0805 chip
120 ohm ±5% 0805 chip
620 ohm ±5% 0805 chip
910 ohm ±5% 0805 chip
100k ohm ±5% 0805 chip
100k ohm ±5% 0805 chip
100k ohm ±5% 0805 chip
100k ohm ±5% 0805 chip
2.2k ohm ±5% 0805 chip
2.2k ohm ±5% 0805 chip
10k ohm ±5% 0805 chip
10k ohm ±5% 0805 chip
10k ohm ±5% 0805 chip
10k ohm ±5% 0805 chip
100k ohm ±5% 0805 chip
10k ohm ±5% 0805 chip
Zero ohm ±5% 0805 chip
Zero ohm ±5% 0805 chip
Zero ohm ±5% 0805 chip
Zero ohm ±5% 0805 chip
Zero ohm ±5% 0805 chip
10k ohm ±5% 0805 chip
1k ohm ±5% 0805 chip
PART
NUMBER
SYMBOL
NUMBER
569-0105-103
569-0105-101
569-0105-100
569-0105-279
569-0105-103
569-0105-301
569-0105-621
569-0105-621
569-0105-222
569-0105-392
569-0105-121
569-0105-621
569-0105-911
569-0105-104
569-0105-104
569-0105-104
569-0105-104
569-0105-222
569-0105-222
569-0105-103
569-0105-103
569-0105-103
569-0105-103
569-0105-104
569-0105-103
569-0105-001
569-0105-001
569-0105-001
569-0105-001
569-0105-001
569-0105-103
569-0105-102
U 008
U 009
U 010
U 011
U 012
U 013
U 014
U 015
U 016
U 017
U 018
U 109
Quad op amp SOIC
Quad op amp SOIC
Quad op amp SOIC
Quad op amp SOIC
Bilateral switch SOIC 4066B
Bilateral switch SOIC 4066B
Bilateral switch SOIC 4066B
Bilateral switch SOIC 4066B
+9V regulator TO-220
+5V regulator TO-220 7805
10W Audio amp TDA2003
Quad op amp SOIC
CR001 Si diode
CR002 Si diode
523-1500-883
523-1500-883
EP001 Receptacle pin contact
515-9024-011
HW001 Strain relief
HW002 4-40 x .25 panhead taptite
HW003 1/4" heatshrink tubing
574-0003-009
575-0604-008
042-0241-555
J 001
J 002
J 003
J 004
1/4" jack
1/4" jack
1/4" jack
1/4" jack
515-0020-005
515-0020-005
515-0020-005
515-0020-005
J 005
16-pin receptacle
515-1538-016
Module box
Panel strain relief
Jack panel
0.688 knob 0.25W/0.156
014-0777-025
017-2210-201
017-2210-202
547-0008-011
Adjustable stop switch
583-2009-010
T 001 600 ohm modem transformer
T 002 600 ohm modem transformer
592-1015-008
592-1015-008
TP001 White vertical tip jack
TP002 Green vertical tip jack
TP003 Yellow vertical tip jack
105-2201-201
105-2204-201
105-2207-201
S 001
U 001
U 002
U 003
U 004
U 005
U 006
U 007
544-3766-004
544-3766-008
544-3766-000
544-2020-008
544-2020-008
544-2020-008
544-2020-008
W 001 15 conductor cable
September 1995
Part No. 004-3039-272
544-2020-008
544-2020-008
544-2020-008
544-2020-008
544-3016-066
544-3016-066
544-3016-066
544-3016-066
544-2003-059
544-2003-016
544-2006-015
544-2020-008
JACK BOX
PART NO. 023-3039-910
MP001
MP002
MP003
MP004
Hex inverter SOIC 74HC04
Quad 2-in AND SOIC HC08
Quad 2-in NAND 74HC00
Quad op amp SOIC
Quad op amp SOIC
Quad op amp SOIC
Quad op amp SOIC
PART
NUMBER
DESCRIPTION
7-10
597-4002-080
SCHEMATICS AND COMPONENT LAYOUTS
SECTION 8 SCHEMATICS AND COMPONENT LAYOUTS
Transistors
(Bottom View Unless Otherwise Specified)
TRANSISTOR BASING DIAGRAM
REFERENCE TABLE
Transistor Part No.
Basing Diagram No.
576-0006-108
1
INTEGRATED CIRCUITS
Typical Integrated Circuit Pin Numbering
September 1995
Part No. 004-3039-272
8-1
SCHEMATICS AND COMPONENT LAYOUTS
Figure 8-1 911 INTERFACE MODULE CONSOLE INTERCONNECT
September 1995
Part No. 004-3039-272
8-2
SCHEMATICS AND COMPONENT LAYOUTS
Figure 8-2 DESK MICROPHONE SCHEMATIC AND BOARD LAYOUT
8-3
September 1995
Part No. 004-3039-272
SCHEMATICS AND COMPONENT LAYOUTS
Figure 8-3 CONSOLE AUDIO PANEL COMPONENT LAYOUT
Figure 8-4 CONSOLE AUDIO PANEL SCHEMATIC
September 1995
Part No. 004-3039-272
8-4
1
2
J3
2 1
R4
5
8
EP4
R7
R6
R2
+
R100
J17
1 2
1
U16
4
8
5
EP7
EP8
C64
EP1
J4
2
1
J12
2
1
J18
2
1
J10
2
C50
1
1
14
1
2
EP6
EP2
EP9
J11
+
4
U13
5
R8
J28
C45
U17
1
R9
4
1
2
C44
EP10
R3
R1
+
RX IN
21
1
C52
2
+
RX OUT
22
+
R5
3
J30
J5
1
Q1
CS4
CS2
5
3
8
6
4
2
J31
TX OUT
1
C67
J8
1 2
2
1
U15
C53
2
EP5
12
CODE
CS8
7
9
CS1
P12V
Y1
10
D
J2
3
1
4
J7
8
5
C66
C46
8
+
13
14
11
D
EP3
Q2
+
7
J29
2 1
S
G
+
RN2
TX IN
S
G
+
U7
RN1
2
14
1
+
GND
VCO
C62
S2
S1
16 18 19
15 17 20
J14
2
1
1
2
J15
J13
1
2
1
2
J16
25
13
PTT
1
+
C51
+
C47
1
C58
+
Z1
2
3
U14
4
5
C60
+
Z2
Z3
J1A
2
20
13
9
11
20
C26
C25
18
16
20
17
15
R47
C30
C17
+ C79
C83 +
R46
C33
R61
1
Vcc
GND
U4
14
24
13
1
8
11
20
C21
1
7
U2
U3
11
20
C20
9
U29
+ C77
R105
R106
16
8
U1
1
10
1
10
C59 +
R111
C8
R37
R32
R41
R59
R101
R66
R79
R64
R78
C54 +
R62
R44
R29
R33
R102
+ C75
C22
R39
R53
+ C48
C47
R45
C81 +
7
7
14
19
10
1
CR1
22
8
U9
1
1
21
11
C41
10
14
8
C2
C23
10
8
+ C76
PTT
1
R48
C16
R16
7
6
U28
1
14
RX OUT
RX IN
U8
C28
5
4
12
U21
C1
R60
7
C32
R35
R40
R15
P12V
R13
R103
R54
+ C49
R34
R42
C27
R30
CS4
CS8
3
CS1
CODE
R12
R68
C35
R57
TX IN
R110
1
10
U5
10
C6
R38
11
R11
R10
20
12
C70 +
C7
11
U6
1
R104
R109
R98
R99
R69
C14
14
TX OUT
8
U12
1
R58
1
U19
R92
C68 +
7
8
R93
C72 +
C78
+ C82
C5
R25
C71 +
R14
R18
7
C70
1
C97
8
U22
R55
C13
C94
R22
7
14
14
C12
11
+ C43
C9
1
C24
20
R17
R23
R24
R19
U11
C3
C80 +
+ C84
R43
C29
R36
R31
R28
7
8
R50
8
1
14
R20
R21
R49
R51
C4
C19
+ C73
R52
C10
R86
R82
7
U18
R27
R26
R56
+ C69
R65
R67
R63
C85
C40
C11
C15
+ C55
R81
R95
+ C61
R96
R77
R84
R83
R85
R90
R89
R87
R76
8
U10
1
R74
C37
R73
C56 +
C38
C39
R91
C57 +
R88
14
14
C65 +
C34
R80
R75
R72
R71
C36
C63 +
C18
C42
COMPONENT SIDE VIEW
FIGURE 8-5
J1B
8-5
OPPOSITE COMPONENT SIDE VIEW
FIGURE 8-6
September 1995
Part No. 004-3039-272
IDC COMPONENT LAYOUTS
+5V
RN2 22k
RN1 22k
31
A0
30
A1
29
A2
28
A3
A4
2 P0
Q0 3
16
1
A4
2 P0
Q0 3
16
1
27
A4
A5
4 P1
Q1 5
15
2
A5
4 P1
Q1 5
15
2
26
A5
A6
6 P2
14
3
A6
6 P2
3
A6
A7
13
4
A7
8 P3
Q2 7
U3
74HC688
Q3 9
14
25
U2
Q2 7
74HC688
8 P3
Q3 9
13
4
24
A7
A8
11 P4
Q4 12
12
5
A8
11 P4
Q4 12
12
5
23
A8
A9
13 P5
Q5 14
11
6
A9
13 P5
Q5 14
11
6
22
A9
A10 15 P6
Q6 16
10
7
A10 15 P6
Q6 16
10
7
21
A10
A11 17 P7
Q7 18
9
8
A11 17 P7
Q7 18
9
8
20
A11
19
A12
18
A13
17
A14
16
A15
15
A16
14
A17
13
A18
12
A19
1
10 9
8
7
6
5
4
3
J7
+5V
Q1
S1
10 9
1
P / EQ / Q 19
P / EQ / Q
G
8
7
6
5
4
3
S2
2
+5V
R93
10k
16 Rx ACTIVE
Q2
6108
DATA BUS (2)
19
G
1
U1A
74HC00
1
3
2
U1B
74HC00
4
6
5
WO13
(Rx WO1 RED)
WO14
(Tx WO1 RED)
D0
2 D1
D1
3 D2
D2
4 D3
D3
5 D4
D4
6 D5
7 OSC OUT
D5
7 D6
D6
8 D7
D7
9 D8
J1B
I/O WR
I/O RD
19
18
SOURCE
+12V
+12V
23
Z1
A0
23 A
A1
22 B
A2
21 C
A3
20 D
G1
O0
+ C58
47
18
1
U6-11 (2)
U4
74HC154
19
G2
SOURCE
-12V
-12V
25
Z2
WO1
(Tx WO5 GRY)
17 PTT ACTIVE
1
+5V
2
PTT IN
R92
10k
J1A
O1
D0
2 D1
Q8 12
D1
3 D2
Q7 13
D2
4 D3
D3
5 D4
D4
6 D5
U5
74HC574
Q1 19
9 D0
D5
7 D6
Q2 18
10 D1
D6
8 D7
Q3 17
D7
9 D8
Q4 16
11 D2 SINGLE TONE 3
ENABLE
12 D3
4
GRP SEL
2 TONE EN
2
6 OSC IN
Y1
3.5795 MHz
Q5 15
11 CLK
+ C60
47
Q6
U7
TP5088
DTMF
Q4 16
CLEAR/CODE
WO2 (Tx WO6 VIO)
WO3 (Rx WO11 BLK)
Q5 15 CS1
U28
74HC574
WO4 (Tx WO11 BLK)
WO5 (Rx WO10 YEL)
Q6 14 CS2
WO6 (Tx WO10 YEL)
WO7 (Rx WO9 BLU)
Q7 13 CS4
WO8 (Tx WO9 BLU)
WO9 (Rx WO8 BRN)
18 Q2
Q8 12 CS8
WO10 (Tx WO8 BRN)
17 Q3
14 TONE OUT
14
+5V
O3
SOURCE
+5V
WO15
O2
+5V
19
D1
18
D2
17
D3
16
D4
D4
15
D5
D5
14
8
D6
D6
13
9
D7
D7
12
3
D1
4
D2
5
D3
6
7
R96
1k
U10C
3403
8
SOURCE
+2.5
+ 10
+ C61
47
C40
. 01
R95
1k
9
R105
12k
MIC ON
+5V
OC
Q1
C EN
R13
10k
11
R10
10k
Q2
Q4
D4 5
U21
74HC573D6 7
Q5
D8 9
Q6
D1 2
Q7
D2 3
Q8
D3 4
Q3
R12
10k
J8
R11
10k
+ C77
22
U29
74HC123
A1 1
1
2
C2
.1
R15
100k
R16
10k
R17
100k
9
+2.5V
J7
U11C
3403
8
R EXT 1
9
U8C
4066
18
R106
1.5M
DTMF MUTE
10 +
15
6 11
DTMF
8 MUTE
U1D
74HC00
12
13
8
U1C
74HC00
9
4
10
Q1
POWER UP MUTE
15
+ C76
47
C EXT 1 14
19
D5 6
+2.5V
PTT INPUTS
R101
100k C75
2. 2
+
D7 8
DTMF LOOPBACK
ADJUST
R100
R103
100k
2.2k
R104
2.2k
EP10
+12V
1
10 +
+5V
+2.5V
R90
3.9k
J12
R89
2.2k
MIC ON
U22D
4066
+2.5V
+2. 5V
EP2
R9
100k
R81
2.2k
R80
2.2k
4
MIC INPUT 1
J18
2
2
R83
620
U10A
3403
6
3 +
C38
.1
+2.5V
R79
100k C54
2.2
5
U10B
3403
7
3
+
C55
2.2
R82
100k
U19-2 (2)
+
C45
10
AUDIO OUT 3
R24
100k
R26
270
U11D
3403
14
WO17 (Rx WO16 BLK)
1
WO20
+
C44
10
13
2
1
U22A
4066
2
U11B
3403
7
NOTES:
1. ALL CAPACITORS ARE IN MICROFARADS AND ALL RESISTORS ARE IN OHMS
UNLESS OTHERWISE SPECIFIED.
2. IC PIN NUMBERS NOT SHOWN:
C3
.1
6
PIN NUMBERS
+12V -12v +5V GND
IC
14
7
U1, U8, U22
20 10
U2, U3, U5, U6, U21, U28
24 12
U4
1
5
U7
4
11
U10
11
4
U11, U19
+ 5
WO19 (Rx WO13 BRN)
AUDIO OUT 4
R18
100k
C4
.1
R21
100k R20
100k
R22
100k
13
C43
2. 2
WO12
(Tx YEL)
+ 12
WO18 (Tx WO16 BLK)
DTMF OUTPUT
ADJUST
R1
R14
100k
2.2k
+ 3
R110
0
J28
C5
.1
R23
100k
U11A
3403
1
WO11
(Tx ORN)
MIC TO
2 RECORDER
+2.5V
3
10
R58
20k
MIC REC
2
25
C71
2.2
+
R85
200k
+12V
R19
2. 2k
12 +
5 +
EP1
U19D
3403
14
13
R84
200k
J2
EP3
MIC AUDIO
ADJUST
R8
R77
100k
10k
U8B
4066
MIC INPUT 2
1
R78
10k
+
R85
100k
+
C39
.1
J7
R94
10k
12
11
10
+2.5V
+ C56
4.7
2
1
DTMF LOOP
U15-3 (2)
U16-3 (2)
MIC ON
R87
300
J10
2
1
U19C
3403
8
9
+ C57
10
2
1
R88
620
R91
620
J11
R25
270
11
12
+12V
+12V
-12V
+5V
13
14
C10
.1
C14
.1
C15
.1
C16
.1
C17
.1
+ C81
15
+ C82
15
C6
.1
C7
.1
C8
.1
C9
.1
C11
.1
+ C83
15
+ C84
15
C12
.1
CR1
CLR1 3
1
29
D0
D0
B1 2
3
+ C59
47
2
Q1 19
3
Z3
WO16
11 CLK
4
C13
.1
C18
.1
C19
.1
C20
.1
C21
.1
C22
.1
C23
.1
September 1995
Part No. 004-3039-272
C24
.1
+ C79
15
+ C80
15
IDC SCHEMATIC (1 OF 2)
FIGURE 8-7
8-6
BACKGROUND
AUDIO ADJUST
R6
100k
R42
2.2k
EP7
R45
2.2k
C32
.1
R48
100k
BACKGROUND AUDIO INPUT 20
J5
1
U12A
2
3403
2
R30
620
C27
.1
3403
5
3 +
2
U12B
6
1
3
7
1
VH
VL
6
U/D
9104
INC
VW
+
U12C
9
5
CS
R34
100k
10
3403
8
C49
2.2
R54
2.2k
AUDIO OUTPUT
ADJUST
R60
R7
2.2k
100k
7
C1
.022
1
R64
220k
2
C35
.047
R66
10k
R38
200k
12
3403
U14
1
R68
22k
13
U12D
13
J4
EP8
BACKGROUND
MUTE GATE
R62 U8A
220k 4066
+
BACKGROUND AUDIO INPUT 21
1
+2.5V
+2.5V
U17
C53
1000
2003
+
4
22 BACKGROUND SPEAKER
2
C51
10
14
+
J29
2
2
BACKGROUND
SPEAKER AUDIO
1 TO RECORDER
+
MIC AUDIO
TO RECORDER
R58 (1)
RECORDER
LEVEL ADJUST
R2
100k
EP9
R66
10
R69
300
R99
10k
R97
4.7k
J7
+
R40
100k
R74
100
R76
2.7
R73
10
C37
.047
+
R35
100k
+
C28
.1
J7
C70
2.2
R57
20k
+
6
3403
U19A
R98
10k
U19B
7
+
+
R67
10
R56
20k
2
3403
1
3
5
R70
300
+
C69
2.2
J30
+
R33
100k
R40
100k
R41
2.2k
EP4
R44
2.2k
3
MAIN AUDIO IN 5
J3
1
U9D
13
3403
2
C25
.1
3403
14
10
12 +
R29
620
2
U9C
9
8
1
VH
VL
U16
U/D
INC
U9B
6
5
9104
5
VW
+
R32
100k
6
3403
7
C48
2.2
R53
2.2k
7
Rx IN
J17
R37
200k
1
R61
220k
C33
.022
R63
220k
U22C
4066
8
9
3
3403
C34
.047
R65
10k
U13
1
R67
22k
6
U9A
2003
+
4
C52
1000
9 MAIN SPEAKER
2
C50
10
1
+
R111
0
Rx OUT
WO22
(Rx WO15 BLU)
2
EP6
R59
2.2k
2
WO21
(Rx WO3 GRN)
MAIN AUDIO IN 6
AUDIO MUTE
GATE
VOLUME
ADJUST
R4
100k
+
CS
SPEAKER AUDIO
TO RECORDER
2
+2.5V
+2.5V
R72
100
R75
2.7
R71
10
C36
.047
+
C26
.1
1
MAIN AUDIO
ADJUST
R5
100k
+
RECORDER OUT 24
+
RECORDER OUT 23
15
16
18
Q5
D1
Q4
D2
U6
Q2
D3
2
D0
3
D1
4
D2
5
D3
6
D4
7
D5
8
D6
9
D7
74HC574
C74
.1
13
R102
100k
12
R47
100k
C30
.1
17
1
J16
C78
.1
U19C-8 (1)
DTMF LOOP
2
C47
10
J31
HANDSET
AUDIO TO
RECORDER
R27
10k
1
C58
2.2
14
6
11
U4-1 (1)
Q3
D6
Q1
D7
Q6
D8
DATA BUS (1)
CLK
+12V
2
HEADSET AUDIO ADJUST
R3
R49
R50
100k
2.2k
2.2k
U22B
C72
2.2
R28
270
U18A
R36
100k
2
3403
1
C29
.1
4
6
+ 5
+
3
+2.5V
3
C41
.1
U18D
3403
14
13
+
C42
.1
+
C62
470
C64
470
+
C63
6.8
+
C65
6.8
+ 14
U18B
3403
7
C73
2.2
4066
+
1
+
VL
VH
5
D5
R55
20k
R31
100k
HEADSET AUDIO IN 7
VW
Q8
HEADSET MUTE
2
C46
10
9104
U/D
CS
+
J13
2
3
R43
270
+
HEADSET AUDIO IN 8
R46
100k
R109
100k
U15
19
+
1
INC
7
D4
Q7
R51
220k
U18C
3403
8
9
5
R52
220k
NOTES:
+ 10
+2.5V
+2.5V
1. ALL CAPACITORS ARE IN MICROFARADS AND ALL RESISTORS ARE IN OHMS
UNLESS OTHERWISE SPECIFIED.
J15
2. IC PINS NOT SHOWN:
2
PIN NUMBERS
1
IC
U13, U14
U9, U12, U18, U19
J14
U8, U22
U15, U16, U17
2
+12V -12V
5
4
+5V GND
3
11
14
7
8
4
1
8-7
September 1995
Part No. 004-3039-272
IDC SCHEMATIC (2 OF 2)
FIGURE 8-8
9
10
TP2
U20
P1
1
TP1
2
3
18
16
1
J4
1
2
3
1
4
5
2
U21
U20
6
3
TP4
7
1
8
9
9
8
10
11
J3
2 1
R1
R25
J1
11 10 9
8 7
6 5 4
3 2 1
C23
R10
R9
R8
R11
1
10
1
10
1
10
18
1
U9
9
U13
20
11
1
U8
9
16
8
1
20
11
8
1
U7
16
9
U6
16
9
C11
8
20
C15
16
7
C38
C4
14
11
8
1
7
U15
U5
8
1
10
1
4
1
C18
7
9
16
8-8
1
U2
U4
PCM SUMMATION BOARD COMPONENT LAYOUT (OPPOSITE COMPONENT SIDE VIEW)
FIGURE 8-10
September 1995
Part No. 004-3039-272
C16
14
C19
C26
8
8
20
C1
R3
R23
C7
R24
U19
C6
C30
R4
C3
R6
1
7
C2
R20
7
R19
C29
C5
U18
1
R7
R2
8
R5
R17
14
1
U3
C17
C24
8
11
U12
C13
20
11
C12
U11
C9
R12
R14
R15
R13
U10
C14
10
C20
1
10
8
C8
R16
C25
U14
U1
1
C33
C37 +
9
C10
R18
+ C35
R22
1
9
16
C27
C32
+ C36
R21
C34 +
PCM SUMMATION BOARD COMPONENT LAYOUT (COMPONENT SIDE VIEW)
FIGURE 8-9
8
14
-12V
+12V
18
U2A
U3A
74HC04
1
2
J4
PCM 1
U5
74HC08
1
3
2
Q6
2
DS2
CLK 2
Q5
Q4
8
Q3
CP
Q2
+5V
1
SYNC 3
9
2
12
3
11
4
10
5
6
6
1Q
1D
2Q
2D
19
2
18
3
17
4
16
5
15
6
V-
VR-
U19D
IO D-
SB
IO D+
B1
13
17
DS1
Q1
Q0
MR
7
5
4
8
3
9
3D
3Q
U15
74HC574D
4Q
4D
5Q
5D
6Q
6D
7Q
7D
8Q
8D
CLK
11
B2
13
8
12
9
VR+
DAC88
R24
12.1k
11
R23
4.99k
C2
51pF
U11
+5V
74HC574D
1
A
B
CLR
R7
18k
TL084
8
NOTES:
10 +
1. ALL RESISTORS ARE IN OHMS AND CAPACITORS ARE IN
MICROFARADS UNLESS OTHERWISE SPECIFIED.
+
C6
1000pF
C5
1000pF
2. IC PIN CONNECTIONS NOT SHOWN:
PIN NUMBER
IO E-
B5
B6
IO E+
B7
EI D
OC
VLC
7
C
EN T
15
16
8
14
U10, U11, U12, U13, U14
U18
U19
20
4
10
11
8
16
R15
240k
1
R14
120k
R13
62k
R12
30k
R11
15k
R10
6.8k
R9
3k
R8
1k
10
1
2
Y4
Y3
Y5
Y2
Y6
U1
Y1
40518
4
6
3
Y0
12
-5V
15
E
Z
A0
8
Vss
+5V
14
9
Vcc
PERO+
CLK0
PWRO-
R25
100k
6
R18
10k
TP2
U18A
13
14
Y7
4
5
A1
U3B
EN P
A2
74HC08
6
D
LD
6
9
GND
7
14
U4, U5, U6, U7, U8, U9
U15, U16, U20
R16
10k
3
C38
430pF
R1
100k
4
R17
750k
11
5
U13
GND D
VFR0
74HC574D
GNDR
PWR I
7
2
11
3 +
C34
10
TL084
1
9
10
9
TL084
8
PDN
10
10 +
15
VFxI-
5
4
VFxI+
12
J3
1
Vout +
2
Vout -
R20
10k
13
U18B
VFR1
TP1
R21
300
R19
10k
U18C
10
+5V
IC
U2, U3
74HC04
5
6
15
R6
18k
TL084
7
C7
.1
U2C
RO
9
U19B
6
+9V
B4
7
14
U16
B3
R2
2.7k
5
CLK
U19C
R5
43k
12 +
16
1
2
R4
43k
TL084
14
5
74HC164
U2B
74HC04
3
4
13
+
Q7
TP3
C4
2200pF
2
6
1
5 +
TL084
7
C35
10
+
TP2
C3
2200pF
R3
2.7k
12
13
V+
C1
51pF
R22
300
CLK
TS_EN
J1
C511 9
C512 10
C513 11
D7 8
D6 7
D5 6
D4 5
D3 4
D2 3
D1 2
11
D7
D6
D7
2
D5
D6
3
D4
D5
4
D3
D4
5
D2
D3
6
D1
D2
7
6
18
5
74HC574D
17
3Q
3D
4
16
3
15
14
14
13
2D
1Q
U10
2Q
4D
4Q
5D
5Q
6Q
6D
H
SH LD 1
D7
2
2
D6
3
D5
4
D4
5
D3
6
D2
7
G
CLK
U9
F
74HC165
E
D
C
CLK INH
15
1Q
2D
2Q
3Q
U11
74HC574D
4D
4Q
5D
5Q
6Q
6D
19
6
18
5
17
4
16
3
15
14
14
13
H
G
CLK INH
F
1
11
CLK
SH LD CLK
1D
3D
2
1
CLK
QH
19
1D
11
9
CLK
15
D7
2
D6
3
D5
4
D4
5
D3
6
D2
7
U8
74HC165
E
D
C
1D
1Q
2D
2Q
3D
U12
74HC574D
3Q
4D
4Q
5D
5Q
6Q
6D
2
1
SH LD CLK
19
6
18
5
17
4
16
3
15
14
14
13
H
G
F
D7
2
D6
3
D5
4
D4
5
D3
6
D2
7
U7
74HC165
E
D
2
19
1Q
SH LD CLK
CLK INH
15
C
19
6
18
5
74HC574D
17
3D
3Q
4
16
3
15
14
14
13
1D
1Q
2D
2Q
U13
4D
4Q
5D
5Q
6Q
6D
18
H
G
17
U6
74HC165
F
E
D
CLK INH
15
D0
2
D1
3
D2
4
2Q
3Q
1D U14
74HC574D
2D
3D
OC
C
CLK
1
D0 1
D0
D1
8
D0
9
7Q
7D
8Q
8D
13
12
12
11
B
A
D1
8
D0
9
7D
7Q
8D
8Q
SER
OC
1
13
12
12
11
OC
B
A
QH
1
10
9
D1
8
D0
9
7D
7Q
8D
8Q
SER
13
12
12
11
B
A
QH
OC
1
10
9
D1
8
D0
9
7D
7Q
8D
8Q
OC
SER
1
10
13
12
12
11
CLK
A
QH
11
11
B
SER
10
9
P1
10
9
SOURCE
-12V
4
SOURCE
-12V
+5V
+12V
C32
.01
3
SOURCE
5
+
6
SOURCE
SOURCE
C36
10
C26
.1
-5V
U21
LM3201
-5V 2
3
-V IN
OUT
GND
C27
.1
1
+
7
C37
10
+12V
C33
.01
C24
.01
C25
.01
+5V
C29
.1
C30
.1
C8
.01
C9
.01
C10
.01
C11
.01
C12
.01
C13
.01
C14
.01
C15
.01
C16
.01
C17
.01
C18
.01
C19
.01
C20
.01
C23
.01
+9V
1
2
8
11
8-9
September 1995
Part No. 004-3039-272
PCM SUMMATION SCHEMATIC
FIGURE 8-11
J20
J24
J23
J22
J21
1
1
1
2
2
2
3
3
3
2
1
J83
3
1
3
3
2
2
2
J82
1
1
J81
1
J80
1
3
4
5
6
3
3
2
2
1
1
J39
3
2
1
2
1
R1
2
1
2
3
4
3
4
5
6
5
6
1
J38
J37
J36
2
26
25
J62
J61
2
U16
R9
R11
T1
R8
R4
R5
J52
TP1
1
2
3
4
5
6
J51
1
2
3
4
5
6
J65
1
2
3
4
5
6
J29
J28
1
J27
1
J26
1
2
2
2
3
3
3
2
1
J34
3
1
3
3
2
2
2
J33
1
J32
1
R3
J17
2
1
J16
3
1
2
J64
3
J8
J13
J44
1
2
3
J42
1
2
3
J41
1
2
3
J43
J48
2
3
2
1
3
2
1
J47
3
2
1
J46
J49
1
J66
R13
2
R2
1
1
2
3
4
5
6
C83
+
C84
+
1
2
3
4
5
6
1
2
3
4
5
6
J63
RV2
RV1
RV3
J14
3
1
2
2
1
R12
J56
1
2
3
4
5
6
J9
3
R10
J15
J57
1
2
3
4
5
6
RV6
RV4
RV5
1
2
J69
2
R6
2
TP2
J31
1
1
1
2
3
4
5
6
3
R7
TP3
J70
1
2
3
4
5
6
C86
+
C85
+
U18
2
R15
1
R14
WO1 WO3 WO2
U17
WO9
C80
+
J68
WO6 WO8 WO7
WO12
WO11
1
WO4
J5
WO13
25
WO10
2
3
4
5
6
J67
1
2
3
4
5
6
26
J18
WO5
J99
1
8
1
9
16
2
1
J19
2
1
3
2
3
J4
T2
1
5
6
9
J1
13
1
25
14
P2
P1
September 1995
Part No. 004-3039-272
911 INTERFACE COMPONENT LAYOUT
(COMPONENT SIDE VIEW)
FIGURE 8-12
8-10
1
R200
R199
R195
C73 +
R197
R196
R223
R227
R225
R306
R198
C17
C20
R47
+
R40
R38
R45
R43
R231
+
C94
R239
+
C90
R231
C93
R230
R242
R46
+
R61
C22
C27
C21
R54
C40
1
+
R56
7
C23
R55
R52
+
R53
C28
R67
14
8
R103
R121
R107
R120
R106
R119
R105
R104
R101
R57
R66
R70
+
+
C24
+
C9
R112
C10
+
7
+
R109
8
R111
C43
U7
1
C39
C42
R108
14
C41
R110
C47
R126
+
R127
R201
7
R194
R192
+ C74
R49
R48
R125
R303
R304
C11 +
C3
U11
R124
+ C53
+ C79
R63
C46
C48
8
R218
+ C54
+
14
R50
R100
C44
R202
R191
R51
R17
+ C52
R300
R203
+
R102
R116
+
R205
R204
R118
CR7
C81
R208
R206
R136
R224
+ C77
R207
8
R137
+ C75
R210
R209
R135
R65
R113
R152
+ C76
R158
R26
+ C60
R154
R153
C14
R39
U5
+ C45
14
R134
R222
C62 +
R159
C2
14
8
R64
R123
7
1
C82
R160
CR4
R23
U14
R114
CR6
R150
R151
+ C51
+
+
U4
R69
R117
U10
R217
1
R21
7
1
7
+
8
C78 +
R133
C99
14
R24
+ C61
R156
U13
+ C59
R216
R251
R131
R132
8
R22
14
R155
R213
+ C68
R138
R157
+
R16
R23
R130
R214
R174
CR5
R178
R173
C18
1
R68
+
C50
7
1
R28
R179
C67 +
R175
U19
R27
R180
R176
7
C26
8
R71
14
7
1
R221
7
C15
7
R177
1
R33
C16
R44
R58
R252
R59
R250
1
+ C69
R181
R302
U9
R172
U12
R128
U1
7
R30
R60
C97
8
R62
R115
14
8
+ C49
R182
8
14
+ C96
R129
R183
R35
R31
C19
R233
R83
C25
R256
R301
R184
R171
+ C72
R231
R243
R82
R80
R85
R95
+
R255
R235
R241
R188
14
1
R98
R257
R32
R81
14
C4
R29
R185
7
1
U6
8
R34
R240
+
R97
Q1
R186
+
U2
R20
+ C70
+ C71
R189
C38 +
+ C58
8
1
R37
R36
C92
R84
7
C34
14
Q2
U15
R14
CR3
R220
+ C66
8
R19
CR2
R147
R142
R187
R190
14
7
1
R148
R143
C33
R99
R149
CR1
7
C57 +
R144
C31
R96
R237
R236
R232
U3
+ C63
R145
R234
R238
8
R146
1
R79
C91
R122
14
R161
U8
R91
C36
R94
R141
R78
C32
8
R86
14
R140
R92
C37
R162
R87
R212
R163
R88
+
R77
R90
R89
R165
R164
C13
R168
+ C6
C12
+ C56
+ C55
C5
R139
8-11
September 1995
Part No. 004-3039-272
C1
R193
R305
C7
R169
R166
R211
R215
R93
C35 +
R167
R170
R219
+ C64
C8
+ C65
+
911 INTERFACE COMPONENT LAYOUT
(OPPOSITE COMPONENT SIDE VIEW)
FIGURE 8-13
R300
0
+12V
3658
P2
R33
2.2k
OPERATOR PTT 13
J8-7 (2)
+5V
+2.5V
R19
10k
SUPERVISOR PTT 12
+
R30
300
R32
620
J21
+
C14
10
C15
4.7
R34
3.9k
J9
J22
1
1
1
2
2
2
3
3
3
WO6
WO1
Q1
OPERATOR PTT 7
R31
620
J1
18 DESK PTT
R29
10k
J8
+2.5V
R20
10k
R18
10k
CR2
17 OUTPUT TX ACTIVE
U3A
U3C
74HC00
74HC00
2
OPERATOR PTT 20
3
1
9
10
U1F
74HC00
8
4
5
CR1
U2D
U3D
U3B
12
74HC04
13
12
6
74HC08
74HC00
12
13
11
13
J8
11
9 OUTPUT TX ACTIVE
SUPERVISOR PTT 18
U2C
74HC08
9
10
CR3
J9
C16
.1
R40
100k
C17
.1
R38
100k
SUPERVISOR TAKEOVER 19
R41
100k
PAGING AUDIO + 1
8
TP1
U4A
2
C18
2.2
R1
500k
R42
2.2k
R43
2.2k
U10D
13
+2.5V
R23
10k
9
8
CR4
J13
PAGING ENABLE 21
9
911 ACTIVE 23
J15
J14
1
3
3
U13A
R142
100k
+4.5V
3
J17
R28
10k
1
+5V
+5V
1
2
74HC00
3
5
R161
2.2k
R11
100k
C64
2.2
9
R234
3.9k
R164
100k
10 +
2
3
3
3
R220
100k
5
3
4
C66
2.2
R171
2.2k
R12
100k
R237
910
+
R241
100k
4066
U4C
9
C92
.1
R238
100k
C94
2.2
R242
2.2k
R8
500k
+4.5V
R243
2.2k
+2.5V
+2.5V
+4.5V
12 +
U9B
6
5
3403
7
C68
2.2
+
R10
100k
+
C95
2.2
C61
2.2
R152
2.2k
1
2
2
3
3
3
9
R154
100k
3 +
U19C
3403
8
R55
100k
C97
2.2
+4.5V
6
U12C
U5A
2
C22
.1
R52
100k
J29
5
3403
7
C62
2.2
+
3403
1
C23
2.2
4
5
J63
C85
10
11 911 AUDIO OUTPUT +
5
1
4
2
3
RV4
J64
2
1
4
5
6
5
2
1
4
5
6
5
2
1
4
5
6
5
2
1
4
5
6
5
2
1
4
5
6
5
C86
10
12 911 AUDIO OUTPUT RV5
R221
100k
R56
2.2k
R2
500k
R57
2.2k
C49
2.2
+
2
U5B
6
R130
10k
R128
10k
3403
7
+2.5V
R129
10k
R13
500k
4066
U19A
2
5 +
R181
2.2k
C70
2.2
R182
2.2k
U15A
TP2
+2.5V
1
C69
2.2
9
+4.5V
R184
100k
10 +
R183
100k
+4.5V
C50
2.2
+2.5V
J65
J65
R186
300
13 PA OUTPUT +
R188
430
U9D
13
12
3403
14
+
C71
2.2
J66
J66
R189
300
R190
68
74HC04
5
U12B
16 911 RECORDER -
U1E
4
R61
2.2k
J57
J57
3403
8
+2.5V
+
15 911 RECORDER +
R187
430
U9C
3403
1
3 +
J56
J56
R159
300
R185
68
8
3 +
2
R59
620
1
R160
68
+2.5V
13
R53
100k
1
+12V
6
+
R51
910
2
R156
300
R158
430
U10B
4066
+
R50
620
5
J64
3403
1
R153
100k
OPERATOR MIC + 1
OPERATOR MIC - 2
6
10 AUXILIARY -
RV6
9
R54
100k
5
R157
430
U10A
10 +
+2.5V
+
R49
120
2
+4.5V
R251
10k
C21
.1
4
J62
T2
+
1
2
R151
51K
R252
10k
R250
10k
J22
1
1
9 AUXILIARY +
R179
300
+
J26
C20
4.7
U14C-8 (2)
+
R47
2.2k
+
2
J63
+
R150
51k
+
C60
2.2
R48
3.9k
5
J62
+
C59
2.2
3658
+2.5V
C19
10
6
R176
300
R155
68
Q2
11
+2.5V
+
5
R180
68
4066
R46
620
4
J61
R169
300
R178
430
U12D
R256
100k
R44
300
1
10
12
R45
620
2
J9
+5V
OP MIC JACK 14
+12V
5
6
R174
100k
3403
14
R255
10k
2 CONSOLE AUDIO OUT WO8
+
2
6
J61
3403
1
3 +
U4D
13
5
R177
430
U9A
2
R173
100k
R239
100k
1
C67
2.2
10 +
DECK MIC - 26
J83
3403
8
4
J52
R170
68
R172
2.2k
U15B
R240
100k
1
R302
0
+
R236
620
12
3403
14
R175
68
DESK MIC + 25
R235
120
13
C65
2.2
+2.5V
C92
.1
2
+
2
1 CONSOLE AUDIO OUT +
WO7
R166
300
R168
430
U8D
+
2
5
WO3
C91
4.7
J81
1
6
J52
3403
8
R163
100k
+
C90
10
R301
0
R167
430
U8C
+
+
5
R149
68
R141
2.2k
+4.5V
R232
620
4
R148
300
R165
68
C63
2.2
R233
2.2k
1
5 +
R257
10k
+2.5V
R230
300
3403
7
+
6
6
+4.5V
J80
6
C58
2.2
U2A
U2B
4
5
U1C
+2.5V
1
1
+5V
3
R231
620
R147
430
U8B
3
J18-1 (2)
U14C-6 (2)
+12V
R143
100k
3 +
U1B
4
2
WO2
3403
1
+2.5V
2
+5V
+4.5V
J51
J51
R145
300
R146
430
U8A
2
2
R26
10k
4066
R141
2.2k
+5V
3
U13B
R24
10k
4066
R22
10k
LOW INPUT
4
R28
10k
1
2
5
LOW INPUT
1
J16
3
4066
HIGH INPUT
2
13
8
U13C
1
HIGH INPUT
2
LOW INPUT
R140
51K
R219
100k
4066
HIGH INPUT
2
6
8
U15C
1
CR6
PA ENABLE 22
C56
2.2
6
74HC04
9
CR5
R139
51k
+
1
2
5 +
+2.5V
C55
2.2
+
R25
10k
4066
3403
7
C57
2.2
+
+5V
R21
10k
R144
68
R9
500k
+
2
6
R215
100k
U12A
U4B
+
R39
100k
1
+2.5V
3 +
PAGING AUDIO - 2
J24
3403
1
+
R37
910
+
R36
620
+
R35
120
10
11
4066
+2.5V
3
+
R58
300
R60
620
J31
+
C24
10
R62
3.9k
C25
4.7
J32
1
1
1
2
2
2
3
3
3
C26
.1
R68
100k
C27
.1
R66
100k
R69
100k
UPERVISOR MIC + 3
R63
620
R65
620
9
J34
1
U5C
3403
8
C28
2.2
R70
2.2k
R3
500k
R71
2.2k
+
R63
120
10 +
SUPERVISOR MIC - 4
R67
100k
2
13
+2.5V
U5D
3403
14
12 +
+2.5V
September 1995
Part No. 004-3039-272
911 INTERFACE SCHEMATIC (1 OF 2)
FIGURE 8-12
8-12
14 PA OUTPUT -
+5V
R132
3.9k
R17
10k
P2
1
U14A
13
GAIN CONTROL HIGH 5
R133
9.1k
4066
2
4
U14B
5
GAIN CONTROL LOW 6
4066
R16
10k
GROUND 7
3
+5V
C63
10
+
1
RV1
RV2
2
4
6
R77
120
C64
10
+
2
C31
.1
R82
100k
C32
.1
R80
100k
4
R78
820
R78
820
R83
100k
U6A
2
3
C33
2.2
3403
1
R4
100k
R84
2.2k
U6B
6
3403
7
U14C
R131
3.9k
4066
9
R102
620
+
C39
10
R104
3.9k
C72
2.2
3403
8
R14
100k
R191
2.2k
R216
100k
R217
100k
C40
4.7
U11A
2
+4.5V
+
C73
2.2
R85
2.2k
R193
100k
3403
1
R194
100k
1
1
2
2
2
3
3
3
C74
2.2
3403
7
C42
.1
R108
100k
R198
430
9
C43
2.2
3403
8
R6
100k
R112
2.2k
R113
2.2k
R205
68
10 +
J44
U7D
13
R136
100k
C75
2.2
12 +
+2.5V
R15
100k
R201
2.2k
C76
2.2
R202
2.2k
+
2
C53
2.2
3403
14
+
R109
100k
1
2
1
4
3
6
5
2
1
4
3
6
5
2
1
4
3
6
5
J68
J69
9 OPERATOR EAR -
J69
R206
300
+
INTERCOM - 6
5
J68
R200
68
+
R107
910
6
8 OPERATOR EAR +
R199
300
R111
100k
U7C
R106
620
3
P2
INTERCOM + 5
R105
120
4
R196
300
5 +
+4.5V
R110
100k
1
R197
430
U11B
6
+4.5V
J15-2 (1)
U2A-2 (1)
C41
.1
J67
2
3 +
C78
2.2
J43
1
J67
10 +
R103
2.2k
J42
U10C
9
6
+
R100
300
8
R134
100k
R195
68
+
5 +
+2.5V
+2.5V
J41
C51
2.2
+
+2.5V
R101
620
R138
100k
C60 (1)
R81
100k
+2.5V
TP3
3 +
RV3
+12V
R85
2.2k
+
911 AUDIO INPUT - 4
T1
600
J20
5
+
J9
911 AUDIO INPUT + 3
J20
3
+
J20
1
10 SUPERVISOR EAR +
+2.5V
+2.5V
R115
620
R203
100k
3403
8
R204
100k
10 +
R117
2.2k
+2.5V
R116
620
+
C44
10
R118
3.9k
J47
J46
+
1
1
2
2
2
3
3
3
C77
2.2
3403
14
R208
430
J70
J70
12 +
C45
4.7
R209
300
+4.5V
J43
1
U11D
13
+4.5V
R114
300
R207
430
+
+12V
U11C
9
C46
.1
R124
100k
R125
100k
J99
1
U7A
R121
910
C47
.1
2
R122
100k
C48
2.2
3403
1
R7
100k
R126
2.2k
1
+
J49
U7B
6
2
R137
100k
R305
10k
R306
1k
J4
SELECT AUDIO OUT
3
C81
10
3
+2.5V
2
+12V
+2.5V
R89
2.2k
R88
620
+
C34
10
R90
3.9k
J37
J36
+
R224
10
C82
.047
11
R222
10k
12
R86
300
R225
2.7
4066
10
+2.5V
CR7
U15D
1
R87
620
R223
100
+
2
C80
1000
2
J19
5 +
+2.5V
5
+
4
C54
2.2
3403
7
+
R123
100k
1
+12V
C79
2.2
R227
10k
+5V
3 +
INSTANT RECALL - 8
15 OPERATOR EAR JACK
R127
2.2k
+
R120
620
+
IINSTANT RECALL + 7
R119
120
11 SUPERVISOR EAR -
R210
68
C35
4.7
+5V
J1
J38
1
1
1
MAIN SPEAKER 9
2
2
2
BACKGROUND SPEAKER 22
3
3
3
J8
18
J5
J1
R304
0
C36
.1
R96
100k
2
HEADSET AUDIO + 7
(CONSOLE)
U6C
WO5
WO10
R92
620
R93
910
C37
.1
9
R94
100k
8
WO4
R5
100k
R98
2.2k
R99
2.2k
+2.5V
10 +
HEADSET AUDIO - 8
WO9
C28
2.2
3403
J39
U6D
13
2
10
4066
SOURCE
C1
.01
C2
.01
C3
.01
C4
.01
C10
.01
+
U16
C9
47
78S09
VOUT
TRANSMIT AUDIO + 3
23 TRANSMIT AUDIO +
3
TRANSMIT AUDIO - 4
C52
2.2
22 TRANSMIT AUDIO -
R135
100k
SELECT AUDIO + 5
21 SELECT AUDIO +
SELECT AUDIO - 6
20 SELECT AUDIO -
+12V 11
15 +12V
+12V 12
12 +12V
8 GROUND
+5V
2
+
GND
1 GROUND UNSELECT
2
GROUND 10
+9V
VIN
11
U14D
+2.5V
+12V
R218
100k
12
3403
14
12 +
+2.5V
1
GROUND UNSELECT 25
+
R95
100k
1
+5V
74HC04
1
1
+
R91
120
R303
0
17
J18
U1A
R97
100k
UNSELECT AUDIO OUT
3
C7
.01
C8
47
SOURCE
GROUND 13
+4.5V
GROUND 14
14 GROUND
INPUT NC 15
11 INPUT NC
R211
2.2k
R212
2.2k
+
C6
2.2
C5
.01
13 GROUND
SOURCE
OUTPUT RX ACTIVE 16
10 OUTPUT RX ACTIVE
SOURCE
UNSELECT AUDIO + 20
6 UNSELECT AUDIO +
+2.5V
UNSELECT AUDIO - 21
5 UNSELECT AUDIO -
RECORDER OUT + 23
3 RECEODER OUT +
RECORDER OUT - 24
2 RECORDER OUT -
WO12
+5V
1
+
C99
47
U17
VIN
LM7805
GND
3
VOUT
2
WO13
+
C11
47
C12
.01
R213
10k
6
5 +
R214
10k
U6D
3403
7
C13
.01
19
16 GROUND
P1
RS-232 RX 2
25 RS-232 RX
RS-232 TX 3
24 RS-232 TX
GROUND 5
4 GROUND
19
P2-13 (1)
J9-20 (1)
CR2 CATHODE (1)
7 OPERATOR PTT
26
8-13
September 1995
Part No. 004-3039-272
911 INTERFACE SCHEMATIC (2 OF 2)
FIGURE8-16
September 1995
Part No. 004-3039-272
911 INTERFACE JACK BOX
FIGURE 8-17
8-14
CUSTOM TO STANDARD KEYBOARD CROSS REFERENCE
APPENDIX A CUSTOM TO STANDARD KEYBOARD CROSS REFERENCE
Definition
Emergency Queue
All Call
Simul Select
Unique ID Queue
Unique ID Directory
All Mute
Hold Queue
Group Directory
Single Mute
Clear Queue
Toggle Queue
Patch
Toggle Menu
Last Receive Calls
Enter Key
Select Call Block 1
Select Call Block 2
Select Call Block 3
Select Call Block 4
Select Call Block 5
Select Call Block 6
Select Call Block 7
Select Call Block 8
Select Call Block 9
Select Call Block 10
Select Call Block 11
Select Call Block 12
Select Call Block 13
Select Call Block 14
Select Call Block 15
Select Call Block 16
Custom
Keyboard
ICON Key
EMR Q
ALLCL
SIMLS
UID Q
UID D
AMUTE
HLD Q
GRP D
SMUTE
CLR Q
TOG Q
PATCH
TOG M
L REC
ENTER
Call Block 1
Call Block 2
Call Block 3
Call Block 4
Call Block 5
Call Block 6
Call Block 7
Call Block 8
Call Block 9
Call Block 10
Call Block 11
Call Block 12
Call Block 13
Call Block 14
Call Block 15
Call Block 16
Standard
Keyboard
Shift F1
Shift F2
Shift F3
Shift F4
Shift F5
Shift F6
Shift F7
Shift F8
Shift F9
Shift F10
Shift F11
Shift F12
CTRL F1
CTRL F2
CTRL F3
CTRL F4
CTRL F5
CTRL F6
CTRL F7
CTRL F8
CTRL F9
CTRL F10
CTRL F11
CTRL F12
ALT F1
ALT F2
ALT F3
ALT F4
ALT F5
ALT F6
ALT F7
A-1
September 1995
Part No. 004-3039-272
CUSTOM TO STANDARD KEYBOARD CROSS REFERENCE
Definition
Call Block 1 Instant XMIT
Call Block 2 Instant XMIT
Call Block 3 Instant XMIT
Call Block 4 Instant XMIT
Call Block 5 Instant XMIT
Call Block 6 Instant XMIT
Call Block 7 Instant XMIT
Call Block 8 Instant XMIT
Call Block 9 Instant XMIT
Call Block 10 Instant XMIT
Call Block 11 Instant XMIT
Call Block 12 Instant XMIT
Call Block 13 Instant XMIT
Call Block 14 Instant XMIT
Call Block 15 Instant XMIT
Call Block 16 Instant XMIT
Relay 1 Control
Relay 2 Control
Relay 3 Control
Relay 4 Control
Relay 5 Control
Relay 6 Control
Relay 7 Control
Relay 8 Control
File Control Key
I/O Mnemonic’s Toggle
Color Menu
Audio Control
Toggle Alarm Window
Reset Alarm 1
Reset Alarm 2
Reset Alarm 3
Reset Alarm 4
Reset Alarm 5
Reset Alarm 6
Reset Alarm 7
Reset Alarm 8
September 1995
Part No. 004-3039-272
Custom
Keyboard
XMIT SEC Call Block 1
XMIT SEC Call Block 2
XMIT SEC Call Block 3
XMIT SEC Call Block 4
XMIT SEC Call Block 5
XMIT SEC Call Block 6
XMIT SEC Call Block 7
XMIT SEC Call Block 8
XMIT SEC Call Block 9
XMIT SEC Call Block 10
XMIT SEC Call Block 11
XMIT SEC Call Block 12
XMIT SEC Call Block 13
XMIT SEC Call Block 14
XMIT SEC Call Block 15
XMIT SEC Call Block 16
CTRL 1
CTRL 2
CTRL 3
CTRL 4
CTRL 5
CTRL 6
CTRL 7
CTRL 8
LOAD/SAVE/FILE
CTRL #
COLOR
AUDIO Key
CTRL 0
SHIFT 1
SHIFT 2
SHIFT 3
SHIFT 4
SHIFT 5
SHIFT 6
SHIFT 7
SHIFT 8
A-2
Standard
Keyboard
Hold Down
ALT A
ALT B
ALT C
ALT D
ALT E
ALT F
ALT G
ALT H
ALT I
ALT J
ALT K
ALT L
ALT M
ALT N
ALT O
ALT P
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
ALT R
ALT S
ALT T
ALT U
ALT V
ALT W
ALT X
ALT Y
ALT Z
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising