APPC0810T
NEXCOM International Co., Ltd.
Industrial Computing Solutions
Applied Panel PC
APPC 0810T, APPC 1210T/1211T, APPC 1510T/1511T
User Manual
NEXCOM International Co., Ltd.
Published December 2010
www.nexcom.com
Contents
Contents
Preface
Chapter 2: Jumpers And Connectors
Copyright .............................................................................................. iii
Disclaimer .............................................................................................. iii
Acknowledgements ............................................................................... iii
Regulatory Compliance Statements . ...................................................... iii
Declaration of Conformity....................................................................... iii
RoHS Compliance................................................................................... iv
Warranty and RMA.................................................................................. v
Safety Information ................................................................................. vi
Installation Recommendations................................................................. vi
Safety Precautions...................................................................................vii
Technical Support and Assistance...........................................................viii
Conventions Used in this Manual...........................................................viii
Global Service Contact Information......................................................... ix
Package Contents................................................................................... xi
Ordering Information..............................................................................xii
Before You Begin...................................................................................15
Precautions............................................................................................15
Jumper Settings.....................................................................................16
Locations of the Jumpers and Connectors..............................................17
Jumpers.................................................................................................19
Connectors Pin Definitions.....................................................................21
APPC 0810T......................................................................................21
APPC 1210T/1211T/1510T/1511T.....................................................39
Chapter 3: BIOS Setup
About BIOS Setup..................................................................................57
When to Configure the BIOS..................................................................57
Entering Setup.......................................................................................58
BIOS Main Menu....................................................................................58
Appendix A: Watchdog Timer
Chapter 1: Product Introduction
WDT Programming Guide......................................................................77
APPC 0810T............................................................................................1
APPC 1210T/1211T..................................................................................4
APPC 1510T/1511T..................................................................................7
Getting to Know the APPC Series...........................................................10
APPC 0810T......................................................................................10
APPC 1210T/1211T/1510T/1511T.....................................................11
Mechanical Dimensions..........................................................................12
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
Appendix B: GPIO Programming Guide
GPIO......................................................................................................79
Appendix C: Power Consumption
Power Consumption Measurement........................................................80
ii
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Preface
Preface
Copyright
Regulatory Compliance Statements
This publication, including all photographs, illustrations and software, is
protected under international copyright laws, with all rights reserved. No
part of this manual may be reproduced, copied, translated or transmitted
in any form or by any means without the prior written consent from
NEXCOM International Co., Ltd.
This section provides the FCC compliance statement for Class A devices
and describes how to keep the system CE compliant.
Declaration of Conformity
FCC
Disclaimer
This equipment has been tested and verified to comply with the limits for
a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are
designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area (domestic environment) is likely to cause harmful interference, in which case the user will be required to correct the interference
(take adequate measures) at their own expense.
The information in this document is subject to change without prior notice
and does not represent commitment from NEXCOM International Co., Ltd.
However, users may update their knowledge of any product in use by constantly checking its manual posted on our website: http://www.nexcom.
com. NEXCOM shall not be liable for direct, indirect, special, incidental, or
consequential damages arising out of the use of any product, nor for any
infringements upon the rights of third parties, which may result from such
use. Any implied warranties of merchantability or fitness for any particular
purpose is also disclaimed.
CE
Acknowledgements
The product(s) described in this manual complies with all applicable European Union (CE) directives if it has a CE marking. For computer systems to
remain CE compliant, only CE-compliant parts may be used. Maintaining
CE compliance also requires proper cable and cabling techniques.
APPC 0810T/1210T/1211T/1510T/1511T is a trademark of NEXCOM International Co., Ltd. All other product names mentioned herein are registered
trademarks of their respective owners.
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
iii
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Preface
RoHS Compliance
How to recognize NEXCOM RoHS Products?
For existing products where there are non-RoHS and RoHS versions, the suffix “(LF)” will be added to the compliant product name.
NEXCOM RoHS Environmental Policy and Status
Update
All new product models launched after January 2006 will be RoHS compliant. They will use the usual NEXCOM naming convention.
NEXCOM is a global citizen for building the digital infrastructure. We are committed to providing green products
and services, which are compliant with European Union
RoHS (Restriction on Use of Hazardous Substance in Electronic Equipment)
directive 2002/95/EU, to be your trusted green partner and to protect our
environment.
RoHS restricts the use of Lead (Pb) < 0.1% or 1,000ppm, Mercury (Hg)
< 0.1% or 1,000ppm, Cadmium (Cd) < 0.01% or 100ppm, Hexavalent
Chromium (Cr6+) < 0.1% or 1,000ppm, Polybrominated biphenyls (PBB) <
0.1% or 1,000ppm, and Polybrominated diphenyl Ethers (PBDE) < 0.1% or
1,000ppm.
In order to meet the RoHS compliant directives, NEXCOM has established an
engineering and manufacturing task force in to implement the introduction
of green products. The task force will ensure that we follow the standard
NEXCOM development procedure and that all the new RoHS components
and new manufacturing processes maintain the highest industry quality
levels for which NEXCOM are renowned.
The model selection criteria will be based on market demand. Vendors and
suppliers will ensure that all designed components will be RoHS compliant.
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
iv
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Preface
Warranty and RMA
NEXCOM Warranty Period
?? Any products returned by NEXCOM to other locations besides the customers’ site will bear an extra charge and will be billed to the customer.
NEXCOM manufactures products that are new or equivalent to new in
accordance with industry standard. NEXCOM warrants that products will
be free from defect in material and workmanship for 2 years, beginning
on the date of invoice by NEXCOM. HCP series products (Blade Server)
which are manufactured by NEXCOM are covered by a three year warranty
period.
Repair Service Charges for Out-of-Warranty Products
NEXCOM will charge for out-of-warranty products in two categories, one
is basic diagnostic fee and another is component (product) fee.
System Level
?? Component fee: NEXCOM will only charge for main components such
as SMD chip, BGA chip, etc. Passive components will be repaired for
free, ex: resistor, capacitor.
NEXCOM Return Merchandise Authorization (RMA)
?? Customers shall enclose the “NEXCOM RMA Service Form” with the
returned packages.
?? Items will be replaced with NEXCOM products if the original one cannot
be repaired. Ex: motherboard, power supply, etc.
?? Customers must collect all the information about the problems encountered and note anything abnormal or, print out any on-screen messages,
and describe the problems on the “NEXCOM RMA Service Form” for
the RMA number apply process.
?? Replace with 3rd party products if needed.
?? If RMA goods can not be repaired, NEXCOM will return it to the customer without any charge.
?? Customers can send back the faulty products with or without accessories (manuals, cable, etc.) and any components from the card, such as
CPU and RAM. If the components were suspected as part of the problems, please note clearly which components are included. Otherwise,
NEXCOM is not responsible for the devices/parts.
Board Level
?? Component fee: NEXCOM will only charge for main components, such
as SMD chip, BGA chip, etc. Passive components will be repaired for
free, ex: resistors, capacitors.
?? Customers are responsible for the safe packaging of defective products,
making sure it is durable enough to be resistant against further damage
and deterioration during transportation. In case of damages occurred
during transportation, the repair is treated as “Out of Warranty.”
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
?? If RMA goods can not be repaired, NEXCOM will return it to the customer without any charge.
v
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Preface
Warnings
Installation Recommendations
Read and adhere to all warnings, cautions, and notices in this guide and
the documentation supplied with the chassis, power supply, and accessory
modules. If the instructions for the chassis and power supply are inconsistent with these instructions or the instructions for accessory modules,
contact the supplier to find out how you can ensure that your computer
meets safety and regulatory requirements.
Ensure you have a stable, clean working environment. Dust and dirt can
get into components and cause a malfunction. Use containers to keep
small components separated.
Adequate lighting and proper tools can prevent you from accidentally
damaging the internal components. Most of the procedures that follow
require only a few simple tools, including the following:
Cautions
Electrostatic discharge (ESD) can damage system components. Do the described procedures only at an ESD workstation. If no such station is available, you can provide some ESD protection by wearing an antistatic wrist
strap and attaching it to a metal part of the computer chassis.
•
•
•
•
Safety Information
Using your fingers can disconnect most of the connections. It is recommended that you do not use needlenose pliers to disconnect connections
as these can damage the soft metal or plastic parts of the connectors.
Before installing and using the device, note the following precautions:
▪▪ Read all instructions carefully.
▪▪ Do not place the unit on an unstable surface, cart, or stand.
▪▪ Follow all warnings and cautions in this manual.
▪▪ When replacing parts, ensure that your service technician uses parts
specified by the manufacturer.
▪▪ Avoid using the system near water, in direct sunlight, or near a heating
device.
▪▪ The load of the system unit does not solely rely for support from the
rackmounts located on the sides. Firm support from the bottom is highly
necessary in order to provide balance stability.
▪▪ The computer is provided with a battery-powered real-time clock circuit.
There is a danger of explosion if battery is incorrectly replaced. Replace
only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer’s instructions.
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
A Philips screwdriver
A flat-tipped screwdriver
A grounding strap
An anti-static pad
vi
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Preface
Safety Precautions
12. If the equipment is not used for a long time, disconnect it from the
power source to avoid damage by transient overvoltage.
1.
2. Keep this User Manual for later reference.
13. Never pour any liquid into an opening. This may cause fire or electrical shock.
3. Disconnect this equipment from any AC outlet before cleaning. Use a
damp cloth. Do not use liquid or spray detergents for cleaning.
14. Never open the equipment. For safety reasons, the equipment should
be opened only by qualified service personnel.
4. For plug-in equipment, the power outlet socket must be located near
the equipment and must be easily accessible.
15. If one of the following situations arises, get the equipment checked
by service personnel:
5. Keep this equipment away from humidity.
a. The power cord or plug is damaged.
6. Put this equipment on a stable surface during installation. Dropping
it or letting it fall may cause damage.
b. Liquid has penetrated into the equipment.
c. The equipment has been exposed to moisture.
7.
d. The equipment does not work well, or you cannot get it to work
according to the user’s manual.
e. The equipment has been dropped and damaged.
8. The openings on the enclosure are for air convection to protect the
equipment from overheating. DO NOT COVER THE OPENINGS.
f. The equipment has obvious signs of breakage.
9. Make sure the voltage of the power source is correct before connecting the equipment to the power outlet.
17. The unit uses a three-wire ground cable which is equipped with a
third pin to ground the unit and prevent electric shock. Do not defeat
the purpose of this pin. If your outlet does not support this kind of
plug, contact your electrician to replace your obsolete outlet.
Read these safety instructions carefully.
Do not leave this equipment in either an unconditioned environment
or in a above 40oC storage temperature as this may damage the
equipment.
16. Do not place heavy objects on the equipment.
10. Place the power cord in a way so that people will not step on it. Do
not place anything on top of the power cord. Use a power cord that
has been approved for use with the product and that it matches the
voltage and current marked on the product’s electrical range label.
The voltage and current rating of the cord must be greater than the
voltage and current rating marked on the product.
18. CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY
REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE
RECOMMENDED BY THE MANUFACTURER. DISCARD USED BATTERIES ACCORDING TO THE MANUFACTURER’S INSTRUCTIONS.
11. All cautions and warnings on the equipment should be noted.
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
19. The computer is provided with CD drives that comply with the appropriate safety standards including IEC 60825.
vii
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Preface
Technical Support and Assistance
Conventions Used in this Manual
1. For the most updated information of NEXCOM products, visit NEXCOM’s website at www.nexcom.com.
Warning: Information about certain situations, which if not
observed, can cause personal injury. This will prevent injury to
yourself when performing a task.
2. For technical issues that require contacting our technical support team
or sales representative, please have the following information ready
before calling:
Caution: Information to avoid damaging components or losing
data.
– Product name and serial number
– Detailed information of the peripheral devices
– Detailed information of the installed software (operating system,
version, application software, etc.)
– A complete description of the problem
– The exact wordings of the error messages
Note: Provides additional information to complete a task easily.
Warning!
1. Handling the unit: carry the unit with both hands and handle it with
care.
2. Maintenance: to keep the unit clean, use only approved cleaning products or clean with a dry cloth.
3. CompactFlash: Turn off the unit’s power before inserting or removing a
CompactFlash storage card.
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
viii
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Preface
Global Service Contact Information
Headquarters
Taiwan
Germany
Leopoldstrase Business Centre, Leopoldstrase 244 80807
Munich, Germany
Tel: +49-89-208039-278
Fax: +49-89-208039-279
http://www.nexcom.eu
18F, No. 716, Chung-Cheng Rd. Chung-Ho City,
Taipei County 235, Taiwan, R.O.C.
Tel: +886-2-8228-0606
Fax: +886-2-8228-0501
http://www.nexcom.com.tw
Italy
USA
Via Gaudenzio Ferrari 29, 21047 Saronno (VA) Italia
Tel: +39 02 9628 0333
Fax: +39 02 9619 8846
http://www.nexcom.eu
3758 Spinnaker Court,
Fremont, CA 94538, USA
Tel: +1-510-656-2248
Fax: +1-510-656-2158
http://www.nexcom.com
United Kingdom
10 Vincent Avenue, Crownhill Business Centre
Milton Keynes, Buckinghamshire, MK8 0AB
United Kingdom
Tel: +44-1908-267121
Fax: +44-1908-262042
http://www.nexcom.eu
France
Z.I. des Amandiers, 17, Rue des entrepreneurs
78420 Carrières sur Seine, France
Tel: +33 (0)1 71 51 10 20
Fax: +33 (0)1 71 51 10 21
http://www.nexcom.eu
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
ix
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Preface
China-Beijing
Japan
Room 301, Block E, Power Creative Building, No. 1
Shangdi East Rd. Haidian Dist., Beijing, 100085, China
Tel: +86-10-5885-6655
Fax: +86-10-5885-1066
http://www.nexcom.cn
9F, Tamachi Hara Bldg.,
4-11-5, Shiba Minato-ku Tokyo,
Japan 108-0014
Tel: +81-3-5419-7830
Fax: +81-3-5419-7832
http://www.nexcom-jp.com
China-Shanghai Office
Room 1505, Greenland He Chuang Building, No. 450
Caoyang Rd. Shanghai, 200063, China
Tel: +86-21-6150-8008
Fax: +86-21-3251-6358
http://www.nexcom.cn
China-Nanjing Office
Room 1206, Hongde Building, No. 20 Yunnan Rd.
Nanjing, 210018, China
Tel: +86-25-8324-9606
Fax: +86-25-8324-9685
http://www.nexcom.cn
China-Shenzhen Office
Western Room 708, Block 210, Tairan Industry & Trading Place,
Futian Area, Shenzhen, China 518040
TEL: +86-755-833 27203
FAX: +86-755-833 27213
http://www.nexcom.cn
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
x
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Preface
Package Contents
Before continuing, verify that the package you received is complete. Your package should have all the items listed in the table.
APPC 0810
APPC 1210T/1211T/1510T/1511T
Item
Part Number
Qty
Item
Part Number
Qty
1
PS2 Y Cable
1
1
PS2 Y Cable
1
2
Panel Mount Kit
6
2
Panel Mount Kit
10
3
Nexcom Driver CD
1
3
Nexcom Driver CD
1
4
Touch Controller CD
1
4
Touch Controller CD
1
5
Touch Pen
1
5
Touch Pen
1
6
Terminal blocks 3-pin Phoenix Contact Plug
1
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
xi
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Preface
Ordering Information
The following provides ordering information for the Applied Panel PC series.
• Barebone
APPC 0810T (P/N: 90IA0810T00X0)
-8” TFT LED Panel PC with Intel® Atom™ N270 1.6 GHz, touch screen,
1GB DDR2
APPC 1210T (P/N: 90IA1210T00X0)
-12.1” TFT LED Panel PC with Intel® Atom™ N270 1.6 GHz, touch
screen, 1GB DDR2
APPC 1211T (P/N: 90IA1211T00X0)
-12.1” TFT LED Panel PC with Intel® Atom™ N270 1.6 GHz, touch
screen, 1GB DDR2, Isolation on 2x RS232/422/485
APPC 1510T (P/N: 90IA1510T00X0)
-15” TFT LED Panel PC with Intel® Atom™ N270 1.6 GHz, touch
screen, 1GB DDR2
APPC 1511T (P/N: 90IA1511T00X0)
-15” TFT LED Panel PC with Intel® Atom™ N270 1.6 GHz, touch
screen, 1GB DDR2, Isolation on 2x RS232/422/485
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
xii
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 1: Product Introduction
Chapter 1: Product Introduction
APPC 0810T
Overview
Key Features
• 4:3 8” fanless LED panel computer
• Intel® Atom™ N270, low consumption CPU
• Fully flat 5-wired touch screen
• Dual GbE; 2nd display VGA
• 2x USB, 1x mini-PCIE, 1x CF, 2x COMs, PS2 KB/MS
• Optional WiFi Module
• DDR2 1GB; 2.5” HDD bracket
• IP65 protection front
• Mounting: Panel/Wall/Stand/VESA 75mm x 75mm
• Wide range power input: 11V~28V
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
1
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 1: Product Introduction
Specifications
Rear I/O
• Serial: 2x RS232
• Ethernet: 2x RJ45
• 2nd display: 1x DB15 VGA port
• Audio: Line-out, Mic-in
• USB: 2x USB 2.0
• PS2 Keyboard/Mouse
• DC power input connector
• Power Switch
Panel
• LED Size: 8”, 4:3
• Resolution: SVGA, 800x600, 262K colors
• Display type: Color TFT LCD
• Luminance: 400 cd/m2
• Contrast ratio: 400:1
• Backlight life time: 40,000 hrs
• Viewing angle: 55(U), 65(D), 65(L), 65(R )
• Backlight: LED
• Touch screen: 5-line Resistive
• Touch light transmission: 80%
• Touch interface: USB
Audio
• AC97 codec: Realtek ALC888
• Audio interfaces: Line-out and Mic-in
Ethernet
• LAN chip: Dual Realtek RTL8111C Gigabit LAN
• Ethernet interface: 10/100/1000 Based-Tx Ethernet compatible
System
• CPU: Intel® Atom™ N270 1.6GHz
• BIOS: 8Mbit Flash BIOS
• I/O chip: ITE8712
• System memory: 1x 200-pin SODIMM socket, supports up to 2GB DDR2
533MHz SDRAM
• SSD: One CF socket via IDE supports Type I/II CompactFlash card
• Hard drive bay: Optional 2.5” SATA HDD
• Watchdog timer: Reset: 1 sec. ~ 255 sec. and 1 min. ~ 255 min.
• H/W status monitor: Monitors system temperature, voltage, and cooling
fan status
• Expansion: Mini-PCIe
• Antenna (optional)
- 1x for GPS (on the top side)
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
Mechanical
• Color: Pantone black U
• IP protection: IP65 front
• Mounting: Panel/Wall/Stand/VESA 75mm x 75mm
• Power input: 11V~28V
• Power adapter: Optional AC power adapter (+12V @5A, 60W)
• Dimension: 231 x 176 x 76 mm
• Weight: 1.41 kg
2
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 1: Product Introduction
Environment
• Vibration
- Vibration Protection with Commercial SATA HDD only
- IEC 68 2-64 @ SINE condition, 2 Grms @ sine, 5~500 Hz, 1O ct./min,
1hr/axis
- IEC 68 2-64 @ Random condition, 0.3 Grms @ sine, 5~500 Hz, 1O ct./
min, 1hr/axis
• Shock
- IEC 68 2-27
- CompactFlash®: 50 G @ wall mount, half sine, 11 ms
- HDD: 30 G @ wall mount, half sine, 16 ms
• Operating Temperature: 0 to 45°C
• Storage temperature: -20 to 75°C
• Operating humidity: 5%~90% relative humidity, non-condensing
• Waterproof/Dustproof
- Front panel IP65
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
3
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 1: Product Introduction
APPC 1210T/1211T
Overview
Key Features
• 4:3 12.1” fanless LED panel computer
• Intel® Atom™ N270, low consumption CPU
• Fully flat 5-wired touch screen
• Dual GbE; 2nd display VGA
• 4x USB, 2x mini-PCIE, 1x CF, PS2 KB/MS
• 2x RS232/422/485 (isolation for APPC 1211T)
• Optional WiFi Module, 2.5” HDD, 2x COMs
• DDR2 1GB; 2.5” HDD bracket
• IP65 protection front
• Mounting: Panel/Wall/Stand/VESA 100mm x 100mm
• Wide range power input: 12V~30V
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
4
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 1: Product Introduction
Specifications
Rear I/O
• Serial: 2x RS232/422/485 (isolation for APPC 1211T)
• Ethernet: 2x RJ45
• 2nd display: 1x DB15 VGA port
• Audio: Line-out
• USB: 4x USB 2.0
• PS2 Keyboard/Mouse
• DC power input connector
• Power Switch
• Optional: 2x COM, GPIO
Panel
• LED Size: 12.1”, 4:3
• Resolution: SVGA, 800x600, 262K colors
• Display type: Color TFT LCD
• Luminance: 350 cd/m2
• Contrast ratio: 300:1
• Backlight life time: 50,000 hrs
• Viewing angle: 50(U), 60(D), 70(L), 70(R )
• Backlight: LED
• Touch screen: 5-line Resistive
• Touch light transmission: 80%
• Touch interface: USB
Audio
• AC97 codec: Realtek ALC888
• Audio interface: Line-out
Ethernet
• LAN chip: Dual Intel 82574L Gigabit LAN
• Ethernet interface: 10/100/1000 Based-Tx Ethernet compatible
System
• CPU: Intel® Atom™ N270 1.6GHz
• BIOS: 8Mbit Flash BIOS
• I/O chip: ITE8783
• System memory: 1x 200-pin SODIMM socket, supports up to 2GB DDR2
400/533MHz SDRAM
• SSD: One CF socket (external, built-in on the top side) supports Type I/II
CompactFlash card
• Hard drive bay: Optional 2.5” SATA HDD or SATA DOM
• Watchdog timer: Reset: 1 sec. ~ 255 min. and 1 sec. or 1 min./step
• H/W status monitor: Monitors system temperature and voltage
• Expansion: 2x Mini-PCIe
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
Mechanical
• Color: Pantone black U
• IP protection: IP65 front
• Mounting: Panel/Wall/Stand/VESA 100mm x 100mm
• Power input: 12V~30V
• Power adapter: Optional AC power adapter (+12V @5A, 60W)
• Dimension: 317 x 243 x 65 mm
• Weight: 3.0 kg
5
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 1: Product Introduction
Environment
• Vibration
- Vibration Protection with Commercial SATA HDD only
- IEC 68 2-64 @ SINE condition, 2 Grms @ sine, 5~500 Hz, 1O ct./min,
1hr/axis
- IEC 68 2-64 @ Random condition, 0.3 Grms @ sine, 5~500 Hz, 1O ct./
min, 1hr/axis
• Shock
- IEC 68 2-27
- CompactFlash®: 50 G @ wall mount, half sine, 11 ms
- HDD: 50 G @ wall mount, half sine, 11 ms
• Operating Temperature: 0 to 45°C
• Storage temperature: -20 to 75°C
• Operating humidity: 5%~90% relative humidity, non-condensing
• Waterproof/Dustproof
- Front panel IP65
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
6
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 1: Product Introduction
APPC 1510T/1511T
Key Features
• 4:3 15” fanless LED panel computer
• Intel® Atom™ N270, low consumption CPU
• Fully flat 5-wired touch screen
• Dual GbE; 2nd display VGA
• 4x USB, 2x mini-PCIE, 1x CF, 2x RS232/422/485, PS2 KB/MS
• Optional WiFi Module, 2.5” HDD, 2x COMs
• DDR2 1GB; 2.5” HDD bracket
• IP65 protection front
• Wide range power input: 12V~30V
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
7
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 1: Product Introduction
Specifications
Rear I/O
• Serial: 2x RS232/422/485 (isolation for APPC 1511T)
• Ethernet: 2x RJ45
• 2nd display: 1x DB15 VGA port
• Audio: Line-out
• USB: 4x USB 2.0
• PS2 Keyboard/Mouse
• DC power input connector
• Power Switch
• Optional: 2x COM, GPIO
Panel
• LED Size: 15”, 4:3
• Resolution: XGA, 1024x768, 262K colors
• Display type: Color TFT LCD
• Luminance: 350 cd/m2
• Contrast ratio: 700:1
• Backlight life time: 50,000 hrs
• Viewing angle: 80(U), 60(D), 80(L), 80(R )
• Backlight: LED
• Touch screen: 5-line Resistive
• Touch light transmission: 80%
• Touch interface: USB
Audio
• AC97 codec: Realtek ALC888
• Audio interface: Line-out
Ethernet
• LAN chip: Dual Intel 82574L Gigabit LAN
• Ethernet interface: 10/100/1000 Based-Tx Ethernet compatible
System
• CPU: Intel® Atom™ N270 1.6GHz
• BIOS: 8Mbit Flash BIOS
• I/O chip: ITE8783
• System memory: 1x 200-pin SODIMM socket, supports up to 2GB DDR2
400/533MHz SDRAM
• SSD: One CF socket (external, built-in on the top side) supports Type I/II
CompactFlash card
• Hard drive bay: Optional 2.5” SATA HDD or SATA DOM
• Watchdog timer: Reset: 1 sec. ~ 255 min. and 1 sec. or 1 min./step
• H/W status monitor: Monitors system temperature and voltage
• Expansion: 2x Mini-PCIe
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
Mechanical
• Color: Pantone black U
• IP protection: IP65 front
• Mounting: Panel/Wall/Stand/VESA 100mm x 100mm
• Power input: 12V~30V
• Power adapter: Optional AC power adapter (+12V @5A, 60W)
• Dimension: 409 x 309 x 62.5 mm
• Weight: 5.0 kg
8
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 1: Product Introduction
Environment
• Vibration
- Vibration Protection with Commercial SATA HDD only
- IEC 68 2-64 @ SINE condition, 2 Grms @ sine, 5~500 Hz, 1O ct./min,
1hr/axis
- IEC 68 2-64 @ Random condition, 0.3 Grms @ sine, 5~500 Hz, 1O ct./
min, 1hr/axis
• Shock
- IEC 68 2-27
- CompactFlash®: 50 G @ wall mount, half sine, 11 ms
- HDD: 50 G @ wall mount, half sine, 11 ms
• Operating Temperature: 0 to 45°C
• Storage temperature: -20 to 75°C
• Operating humidity: 5%~90% relative humidity, non-condensing
• Waterproof/Dustproof
- Front panel IP65
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
9
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 1: Product Introduction
Getting to Know the APPC Series
COM1 and COM2
The COM ports support RS232 compatible serial devices.
APPC 0810T
Line-out
Power Switch
Used to power-on or power-off the system.
PS/2 KB/MS
DC Input Mic-in
LAN
Used to connect the system to a local area network.
COM2
USB
Used to connect USB 2.0/1.1 devices.
VGA
Used to connect an analog VGA monitor.
Power
switch
USB
LAN
VGA
COM1
DC Input
Used to plug a DC power cord.
Mic-in
Used to connect an external microphone.
Line-out
Used to connect a headphone or a speaker.
PS/2 Keyboard/Mouse
Used to connect a PS/2 keyboard and a PS/2 mouse via a cable.
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
10
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 1: Product Introduction
APPC 1210T/1211T/1510T/1511T
Line-out
PS/2 Keyboard/Mouse
Used to connect a PS/2 keyboard and a PS/2 mouse via a cable.
PS/2 KB/MS
VGA
Used to connect an analog VGA monitor.
DC Input
Used to plug a DC power cord.
Power
switch
USB
LAN
COM1
USB
COM2
Rear Side of APPC 1210T/1211T/1510T/1511T
VGA
DC Input
Power Switch
Used to power-on or power-off the system.
Line-out
Used to connect a headphone or a speaker.
COM3
GPIO
COM4
LAN
Used to connect the system to a local area network.
USB
Used to connect USB 2.0/1.1 devices.
COM3 and COM4 (for APPC 1211T/1511T)
The COM ports support RS232 compatible serial devices.
COM1 and COM2
The COM ports support RS232/422/485 compatible serial devices. APPC
1211T/1511T supports isolation on RS232/422/485 serial devices.
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
GPIO (for APPC 1211T/1511T)
General Purpose I/O for digital input/output control.
11
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 1: Product Introduction
Mechanical Dimensions
APPC 0810T
231
M
75
141.6
170.4
176
176
121.5
6.4
88
75
4-
231
162
4
7
11
69
76
218.3
170
11
11
30.5
170
30.5
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
12
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 1: Product Introduction
APPC 1210T/1211T
186.4
243.00
247.7
View Area
173.90
225.65
317.00
270.00
100.00
100.00
28.55
13.95 +/- 0.50
45.50
134.45
28
65.00
8.00
299.50
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
13
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 1: Product Introduction
APPC 1510T/1511T
194.75
189.75
30.25
17.55
389.50
359.25
409.00
270.00
100.00
100.00
173.45
289.50
128.55
28.55
40.25
249.25
389.50
25.50
62.50
6.20
11.35
309.00
231.30
39.95
17.55
306.00
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
14
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 2: Jumpers and Connectors
Chapter 2: Jumpers and Connectors
This chapter describes the jumpers and connectors on the motherboard.
Note that information in this chapter applies to APPC 0810T/1210T/
1211T/1510T/1511T.
tronic components. Humid environment tend to have less static electricity than dry environments. A grounding strap is warranted whenever
danger of static electricity exists.
Before You Begin
Precautions
• Ensure you have a stable, clean working environment. Dust and dirt can
Computer components and electronic circuit boards can be damaged by
discharges of static electricity. Working on the computers that are still connected to a power supply can be extremely dangerous.
get into components and cause a malfunction. Use containers to keep
small components separated.
Follow the guidelines below to avoid damage to your computer or yourself:
• Adequate lighting and proper tools can prevent you from accidentally
damaging the internal components. Most of the procedures that follow
require only a few simple tools, including the following:
• Always disconnect the unit from the power outlet whenever you are
working inside the case.
• A Philips screwdriver
• A flat-tipped screwdriver
• If possible, wear a grounded wrist strap when you are working inside
• A set of jewelers Screwdrivers
the computer case. Alternatively, discharge any static electricity by
touching the bare metal chassis of the unit case, or the bare metal body
of any other grounded appliance.
• A grounding strap
• An anti-static pad
• Using your fingers can disconnect most of the connections. It is recom-
• Hold electronic circuit boards by the edges only. Do not touch the com����
mended that you do not use needle-nosed pliers to disconnect connections as these can damage the soft metal or plastic parts of the connectors.
ponents on the board unless it is necessary to do so. Don’t flex or stress
the circuit board.
• Leave all components inside the static-proof packaging that they
• Before working on internal components, make sure that the power
shipped with until they are ready for installation.
is off. Ground yourself before touching any internal components, by
touching a metal object. Static electricity can damage many of the elec-
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
• Use correct screws and do not over tighten screws.
15
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 2: Jumpers and Connectors
Jumper Settings
A jumper is the simplest kind of electric switch. It consists of two metal
pins and a cap. When setting the jumpers, ensure that the jumper caps are
placed on the correct pins. When the jumper cap is placed on both pins,
the jumper is short. If you remove the jumper cap, or place the jumper
cap on just one pin, the jumper is open.
Refer to the illustrations below for examples of what the 2-pin and 3-pin
jumpers look like when they are short (on) and open (off).
Two-Pin Jumpers: Open (Left) and Short (Right)
Three-Pin Jumpers: Pins 1 and 2 Are Short
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
16
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 2: Jumpers and Connectors
Locations of the Jumpers and Connectors
APPC 0810T
VGA
COM 1
USB 2.0 LAN 1
LAN 2
CN4
JP12/JP13/JP14/JP15
JP11
CN3
JP8
J5
JP9
JP10
J2
J3
CON2
CN2
J4
FAN1
JP4
JP6
JP5
JP7
CN1 JP3 JP1
JP2
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
SATA SATA
power
17
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 2: Jumpers and Connectors
APPC 1210T/1211T/1510T/1511T
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
18
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 2: Jumpers and Connectors
Jumpers
Panel Power Select
Clear CMOS
Connector type: 1x3 3-pin header, 2.54 mm pitch
Connector location: JP8
Connector type:1x3 3-pin header, 2.54 mm pitch
Connector location: JP4
3
1
3
1
Pin
Definition
Pin
1-2 On
3.3V
1-2 On
Normal
2-3 On
5V
2-3 On
CMOS Clear
1-2 On: default
Settings
1-2 On: default
Pin
Definition
1
VCC3
1
Battery 3.3V
2
Panel power
2
RTCRST#
3
VCC5
3
GND
Pin
Definition
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
19
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 2: Jumpers and Connectors
Power Type Select
Connector type: 1x3 3-pin header, 2.54 mm pitch
Connector location: JP9 (APPC 0810T)
JP5 (APPC 1210T/1211T/1510T/1511T)
3
1
Pin
Definition
1-2 On
AT Mode
2-3 On
ATX Mode
2-3 On: default
Pin
Definition
1
AUTO_BOT
2
PUSH_BOT
3
ATX_BOT
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
20
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 2: Jumpers and Connectors
Connector Pin Definitions
APPC 0810T
External I/O Interface
VGA Port
RS232 COM1/COM2 Port
Connector type: DB-15 port, 15-pin D-Sub
Connector location: VGA1
Connector type: DB-9
Connector location: COM1/CN1
5
1
9
15
1
6
11
Pin
Pin
5
Definition
Pin
1
Definition
Definition
DCD
Pin
Definition
6
DSR
1
RED_VGA
9
VGA_VCC
2
RxD
7
RTS
2
GREEN_VGA
10
GND
3
TxD
8
CTS
3
BLUE_VGA
11
NC
4
DTR
9
RI
4
NC
12
VGA_DDC_DATA
5
GND
5
GND
13
G_HSYNC
6
GND
14
G_VSYNC
7
GND
15
VGA_DDC_CLK
8
GND
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
21
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 2: Jumpers and Connectors
USB Ports
PS/2 Keyboard/Mouse Port
Connector type: Dual USB port
Connector location: CN5
Connector type: PS/2, Mini-DIN-6, JST-2.0mm-M-180
Connector location: JP7
5
3
6
4
2 1
Pin
Definition
Pin
Pin
Definition
1
Definition
5VSB
Pin
2
Definition
KDAT
1
VCC5
5
VCC5
2
USB0-
6
USB1-
3
KCLK
4
MDAT
5
MCLK
6
GND
3
USB0+
7
USB1+
4
GND
8
GND
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
22
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 2: Jumpers and Connectors
LAN1 Port
LAN2 Port
Connector type: RJ45 port with LEDs
Connector location: LAN1
Connector type: RJ45 port with LEDs
Connector location: LAN2
Act
Link
Act
Act
Status
Link
Status
Orange
Blinking
Data Activity
Green
Always Lighted
Linked
Off
No Acitivity
Off
No Link
Pin
Definition
Pin
Link
Act
Definition
Status
Link
Status
Orange
Blinking
Data Activity
Green
Always Lighted
Linked
Off
No Acitivity
Off
No Link
Pin
LAN2_TXD0N
3
LAN2_TXD1P
4
LAN2_TXD2P
3
LAN1_TXD1P
4
LAN1_TXD2P
5
LAN2_TXD2N
6
LAN2_TXD1N
5
LAN1_TXD2N
6
LAN1_TXD1N
7
LAN2_TXD3P
8
LAN2_TXD3N
7
LAN1_TXD3P
8
LAN1_TXD3N
9
LAN2_LINKLED#
10
VCC3
9
LAN1_LINKLED#
10
VCC3
11
LAN2_ACTLED#
12
VCC3
11
LAN1_ACTLED#
12
VCC3
MH1
GND_CHASSIS
MH2
MH1
GND_CHASSIS
MH2
23
2
Definition
2
GND_CHASSIS
LAN1_TXD0P
Pin
LAN2_TXD0P
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
1
Definition
1
LAN1_TXD0N
GND_CHASSIS
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 2: Jumpers and Connectors
Line-out Jack
Mic-in Jack (APPC 0810T only)
Connector type: 1x5 5-pin header, 2.0 mm pitch
Connector location: JP6
Connector type: 1x4 4-pin header, 2.0 mm pitch
Connector location: JP5
5
1
4
1
JP6
JP5
Rear Panel
Rear Panel
Pin
Definition
Pin
1
LOUT_L+
1
MIC_L
2
LOUT_L-
2
GND
3
GND
3
GND
4
LOUT_R+
4
MIC_R
5
LOUT_R-
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
24
Definition
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 2: Jumpers and Connectors
11V-28V DC Input
Connector type: Terminal Blocks 3-pin Phoenix Contact 5.08mm pitch
Connector location:
1
Pin
2
3
Definition
1
+
2
-
3
FG
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
25
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 2: Jumpers and Connectors
Internal Connectors
VGA Connector
LVDS Channel A Connector (APPC 0810T)
Connector type:2x8 16-pin box header, 2.0 mm pitch
Connector location: CN8
Connector type: 2x10 20-pin, LCD-1.25mm-M-180
Connector location: CN3
MH1
16
15
2
1
Pin
Definition
Pin
Definition
1
19
2
20
1
RED_VGA
9
VGA_VCC
2
GREEN_VGA
10
GND
3
BLUE_VGA
11
NC
4
NC
12
VGA_DDC_DATA
5
GND
13
G_HSYNC
6
GND
14
G_VSYNC
3
7
GND
15
VGA_DDC_CLK
4
8
GND
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
MH2
Pin
26
Definition
Pin
Definition
1
11
LVDSA_CLK1P
2
12
LVDSA_TX1N
VDD
13
LVDSA_CLK1N
LVDSA_TX0P
14
LVDSA_GND
5
LVDSA_TX3P
15
LVDSA_GND
6
LVDSA_TX0N
16
VCC12
7
LVDSA_TX3N
17
LVDSA_CLK2P
8
VDD
18
VCC12
9
LVDSA_GND
19
LVDSA_CLK2N
10
LVDSA_TX1P
20
LVDSA_GND
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 2: Jumpers and Connectors
LVDS Channel B Connector (APPC 0810T)
Panel Backlight Connector
Connector type: 2x10 20-pin, LCD-1.25mm-M-180
Connector location: CN4
Connector type: JST 7-pin, 2.54 mm pitch
Connector location: J5
MH1
1
19
2
20
1
7
MH2
Pin
Definition
1
2
3
VDD
Pin
Definition
Pin
Definition
1
+5V
11
LVDSB_CLK2P
2
+12V
12
LVDSB_TX5N
3
+12V
13
LVDSB_CLK2N
4
NC
GND
4
LVDSB_TX4P
14
LVDSB_GND
5
5
LVDSB_TX7P
15
LVDSB_GND
6
GND
7
Backlight Enable
6
LVDSB_TX4N
16
VCC12
7
LVDSB_TX7N
17
LVDSB_CLK6P
8
VDD
18
VCC12
9
LVDSB_GND
19
LVDSB_CLK6N
10
LVDSB_TX5P
20
LVDSB_GND
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
27
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 2: Jumpers and Connectors
Push Button Connector
Reset Button
Connector type:1x2 2-pin header, 2.0 mm pitch
Connector location: JP10
Connector type:1x2 2-pin header, 2.0 mm pitch
Connector location: JP1
2
1
Pin
2
1
Pin
Definition
1
VCC3
Definition
1
RESET#
2
LAN1_ACTLED#
2
GND
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
28
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 2: Jumpers and Connectors
Power LED Connector
HDD Active LED Connector
Connector type:1x2 2-pin header, 2.0 mm pitch
Connector location: JP3
Connector type:1x2 2-pin header, 2.0 mm pitch
Connector location: JP2
2
1
Pin
2
1
Definition
Pin
Definition
1
VCC5
1
VCC5
2
GND
2
HD_LED#
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
29
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 2: Jumpers and Connectors
SMBus Connector
LAN1 Active LED Connector
Connector type: 1x3 3-pin header, 2.0 mm pitch
Connector location: JP11
Connector type:1x2 2-pin header, 2.0 mm pitch
Connector location: JP14
3
1
2
1
Pin
Definition
Pin
1
SMB_DATA
1
VCC3
2
SMB_CLK
2
LAN1_ACTLED#
3
GND
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
30
Definition
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 2: Jumpers and Connectors
LAN1 Link LED Connector
LAN2 Active LED Connector
Connector type:1x2 2-pin header, 2.0 mm pitch
Connector location: JP15
Connector type:1x2 2-pin header, 2.0 mm pitch
Connector location: JP12
2
1
Pin
2
1
Definition
Pin
Definition
1
VCC3
1
VCC3
2
LAN1_LINKLED#
2
LAN2_ACTLED#
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
31
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 2: Jumpers and Connectors
LAN2 Link LED Connector
PS/2 Keyboard/Mouse Connector
Connector type:1x2 2-pin header, 2.0 mm pitch
Connector location: JP13
Connector type:2x4 8-pin header, 2.54 mm
Connector location: JP7
2
1
2
1
Pin
Definition
1
VCC3
2
LAN2_LINKLED#
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
8
7
Pin
1
32
Definition
VCC5
Pin
2
Definition
VCC5
3
KB_DATA
4
LM_DATA
5
KB_CLK
6
LM_CLK
7
GND
8
GND
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 2: Jumpers and Connectors
SATA Port
SATA Power Connector
Connector type: Standard Serial ATAII 7P (1.27mm, SATA-M-180)
Connector location: J1
Connector type: 4-pin JST wafer, 2.54 mm pitch
Connector location: CON1
7
1
4
1
Pin
Definition
GND
1
VCC12
2
TXP0
2
GND
3
TXN0
3
GND
4
GND
4
VCC5
5
RXN0
6
RXP0
7
GND
Pin
1
Definition
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
33
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 2: Jumpers and Connectors
RS232 Serial Port Connectors
USB Port Connector
Connector type:2x5 10-pin boxed header, 2.0 mm pitch
Connector location: CN1 and CN2
Connector type:1x6 6-pin boxed header, JST-2.0mm-M-180
Connector location: J2
2
1
6
10
9
Pin
Definition
Pin
1
Definition
Pin
Definition
VCC5
1
DCD
2
RXD
1
3
TXD
4
DTR
2
USB2USB2+
5
GND
6
DSR
3
7
RTS
8
CTS
4
USB3-
NC
5
USB3+
6
GND
9
RI
10
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
34
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 2: Jumpers and Connectors
USB DOM Connector
GPIO Connector
(4 digital input and 4 digital output)
Connector type: 2x5 10-pin header, 2.0 mm pitch
Connector location: J3
Connector type:2x5 10-pin header, 2.0 mm-M-180
Connector location: J4
1
2
9
10
Pin
Definition
Pin
Definition
1
VCC5
2
VCC5
3
USB4-
4
USB5-
5
USB4+
6
USB5+
7
GND
8
GND
9
GND
10
GND
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
1
2
9
10
Pin
1
35
Definition
VCC5
Pin
2
Definition
GND
3
SIO_GPI54-(GPO)
4
SIO_GPO50-(GPI)
5
SIO_GPI55-(GPO)
6
SIO_GPO51-(GPI)
7
SIO_GPI56-(GPO)
8
SIO_GPO52-( GPI)
9
SIO_GPI57-(GPO)
10
SIO_GPO53-(GPI)
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 2: Jumpers and Connectors
System Fan
DC Power Input Connector
Connector type: 3-pin Wafer, 2.54 mm pitch
Connector location: FAN1
Connector type:2x2 AUX power connector
Connector location: CON2
1
1
3
2
4
3
Pin
Definition
1
GND
2
+12V
3
SENSE
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
36
Pin
Definition
1
GND
2
GND
3
12V DC-IN
4
12V DC-IN
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 2: Jumpers and Connectors
CompactFlash
Pin
Description
Pin
Description
Connector type: CompactFlash Type 2
Connector location: CN6
29
SDD13A
30
SDD14A
31
SDD15A
32
SDCS#3
33
NC
34
SDIOR#
35
SDIOW#
36
VCC
37
HDIRQ14
38
VCC
39
CF_SEL#
40
NC
41
IDERST#
42
SIORDY
43
SDREQ
44
SDDACK#
45
IDEACTP#
46
DIAG#
Description
47
SDD8A
48
SDD9A
49
SDD10A
50
GND
Pin
Description
Pin
1
GND
2
SDD3A
3
SDD4A
4
SDD5A
5
SDD6A
6
SDD7A
7
SDCS#1
8
GND
9
GND
10
GND
11
GND
12
GND
13
VCC
14
GND
15
GND
16
GND
17
GND
18
SDA2A
19
SDA1A
20
SDA0A
21
SDD0A
22
SDD1A
23
SDD2A
24
NC
25
CF_CD2#
26
CF_CD1#
27
SDD11A
28
SDD12A
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
37
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 2: Jumpers and Connectors
Mini-PCIe Slots
Pin
Connector location: CN7
31
1
51
2
52
Pin
Definition
Pin
Definition
1
WAKE0#
2
+V3.3_MINI
3
NC
4
GND
5
NC
6
+V1.5S_MINI
7
NC
8
NC
9
GND
10
NC
11
GPP_CLK0_N
12
NC
13
GPP_CLK0_P
14
NC
15
GND
16
NC
17
NC
18
GND
19
NC
20
MINICARD1_DIS#
21
GND
22
PCIE_RST#
23
PCIE_RX2N
24
+V3.3A_MINI
25
PCIE_RX2P
26
GND
27
GND
28
+V1.5S_MINI
29
GND
30
SMB_CLK
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
38
Definition
Pin
PCIE_TX2N
32
Definition
SMB_DAT
33
PCIE_TX2P
34
GND
35
GND
36
USB_6N
37
GND
38
USB_6P
39
+V3.3A_MINI
40
GND
41
+V3.3A_MINI
42
NC
43
GND
44
NC
45
NC
46
NC
47
NC
48
+V1.5S_MINI
49
NC
50
GND
51
NC
52
+V3.3A_MINI
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 2: Jumpers and Connectors
APPC 1210T/1211T/1510T/1511T
External I/O Interface
VGA Port
USB 0/1 Ports
Connector type: DB-15 port, 15-pin D-Sub
Connector location: VGA1
Connector type: Dual USB port
Connector location: CN2
5
1
15
11
Pin
Definition
Pin
Definition
1
RED_VGA
9
VGA_VCC
2
GREEN_VGA
10
GND
3
BLUE_VGA
11
NC
4
NC
12
VGA_DDC_DATA
5
GND
13
G_HSYNC
6
GMA_DRIVER
14
G_VSYNC
7
GND
15
VGA_DDC_CLK
8
GND
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
Pin
39
Definition
Pin
Definition
1
VCC5
5
VCC5
2
USB0-
6
USB1-
3
USB0+
7
USB1+
4
GND
8
GND
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 2: Jumpers and Connectors
USB 2/3 Ports
PS/2 Keyboard/Mouse Port
Connector type: Dual USB port
Connector location: CN3
Connector type: PS/2, Mini-DIN-6, JST-2.0mm-M-180
Connector location: KM1
5
3
6
4
2 1
Pin
Definition
Pin
Pin
Definition
1
Definition
5VSB
Pin
2
Definition
KDAT
1
VCC5
5
VCC5
2
USB2-
6
USB3-
3
KCLK
4
MDAT
5
MCLK
6
GND
3
USB2+
7
USB3+
4
GND
8
GND
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
40
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 2: Jumpers and Connectors
Line-out Jack
RS232 COM1 Port
Connector type: 1x5 5-pin header, 2.0 mm pitch
Connector location: CN1
Connector type: DB-9
Connector location: COM1
9
5
1
1
5
6
CN1
Rear Panel
Pin
Definition
1
LOUT_R
2
LOUT_JD
3
NC
4
LOUT_L
5
AGND
6
AGND
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
41
Pin
Definition
Pin
Definition
1
COM1_DCD_C
2
COM1_RXD_C
3
COM1_TXD_C
4
COM1_DTR_C
5
ISO1_GND
6
COM1_DSR_C
7
COM1_RTS_C
8
COM1_CTS_C
9
COM1_RI_C
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 2: Jumpers and Connectors
RS232 COM2 Port
LAN1 Port
Connector type: DB-9
Connector location: COM2
Connector type: RJ45 port with LEDs
Connector location: LAN1
9
1
5
Act
Link
6
Pin
Definition
Pin
Definition
1
COM2_DCD_C
2
COM2_RXD_C
3
COM2_TXD_C
4
COM2_DTR_C
5
ISO1_GND
6
COM2_DSR_C
7
COM2_RTS_C
8
COM2_CTS_C
9
COM2_RI_C
Act
Status
Link
Status
Orange
Blinking
Data Activity
Green
Always Lighted
Linked
Off
No Acitivity
Off
No Link
Pin
1
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
42
Definition
LAN1_M0P
Pin
2
Definition
LAN1_M0N
3
LAN1_M1P
4
LAN1_M2P
5
LAN1_M2N
6
LAN1_M1N
7
LAN1_M3P
8
LAN1_M3N
9
LAN1_LED_ACT#
10
LAN1_LED1+
11
LAN1_LINK
12
LIN1_LINK100#
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 2: Jumpers and Connectors
LAN2 Port
12V-30V DC Input
Connector type: RJ45 port with LEDs
Connector location: LAN2
Connector type: DC 4-pin DIN Power Jack with Shield, 90°
Connector location: CN8
Act
Link
2
4
1
3
Act
Status
Link
Status
Orange
Blinking
Data Activity
Green
Always Lighted
Linked
Off
No Acitivity
Off
No Link
Pin
Definition
Pin
Definition
Pin
Definition
1
VIN
2
VIN
3
GND
4
GND
Definition
1
LAN2_M0P
2
LAN2_M0N
3
LAN2_M1P
4
LAN2_M2P
5
LAN2_M2N
6
LAN2_M1N
7
LAN2_M3P
8
LAN2_M3N
9
LAN2_LED_ACT#
10
LAN2_LED1+
11
LAN2_LINK
12
LIN2_LINK100#
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
Pin
43
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 2: Jumpers and Connectors
Internal Connectors
945GSE LVDS Channel A Connector
(APPC 1210T/1211T/1510T/1511T)
945GSE LVDS Channel B Connector (APPC 1511T)
Connector type: 2x10 20-pin, LCD-1.25mm-M-180
Connector location: LVDS1B1
Connector type: 2x10 20-pin, LCD-1.25mm-M-180
Connector location: LVDS1A1
MH1
MH1
1
19
2
20
1
19
2
20
MH2
MH2
Pin
Pin
Definition
Pin
Definition
Definition
Pin
Definition
1
L_DDC_CLK
2
L_DDC_DATA
1
L_DDC_CLK
2
L_DDC_DATA
3
PANEL1_VDD(OUTPUT)
4
LB_DATAP0
3
PANEL1_VDD(OUTPUT)
4
LA_DATAP0
5
NC
6
LB_DATAN0
5
NC
6
LA_DATAN0
7
NC
8
PANEL1_VDD(OUTPUT)
7
NC
8
PANEL1_VDD(OUTPUT)
9
GND_LVDS1
10
LB_DATAP1
9
GND_LVDS1
10
LA_DATAP1
11
LB_CLKP
12
LB_DATAN1
11
LA_CLKP
12
LA_DATAN1
13
LB_CLKN
14
GND_LVDS1
13
LA_CLKN
14
GND_LVDS1
15
GND_LVDS1
16
PANEL1_BACKLIGHT
15
GND_LVDS1
16
PANEL1_BACKLIGHT
17
LB_DATAP2
18
PANEL1_BACKLIGHT
17
LA_DATAP2
18
PANEL1_BACKLIGHT
19
LB_DATAN21
20
GND_LVDS1
19
LA_DATAN21
20
GND_LVDS1
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
44
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 2: Jumpers and Connectors
CH7308 LVDS Channel A Connector (APPC 1510T/1511T)
CH7308 LVDS Channel B Connector (APPC 1511T)
Connector type: 2x10 20-pin, LCD-1.25mm-M-180
Connector location: LVDS2A1
Connector type: 2x10 20-pin, LCD-1.25mm-M-180
Connector location: LVDS2B1
MH1
MH1
1
19
1
19
2
20
2
20
MH2
Pin
Definition
MH2
Pin
Definition
Pin
2
Definition
2
SD_DDC
3
PANEL1_VDD(OUTPUT)
4
LVDS2_TXL0P
3
PANEL1_VDD(OUTPUT)
4
LVDSB_TXL0P
5
LVDS2_TXL3P
6
LVDS2_TXL0N
5
LVDSB_TXL3P
6
LVDSB_TXL0N
7
LVDS2_TXL3N
8
PANEL1_VDD(OUTPUT)
7
LVDSB_TXL3N
8
PANEL1_VDD(OUTPUT)
9
GND_LVDS2
10
LVDS2_TXL1P
9
GND_LVDS2
10
LVDSB_TXL1P
11
LVDS2_CLKP
12
LVDS2_TXL1N
11
LVDSB_CLKP
12
LVDSB_TXL1N
13
LVDS2_CLKN
14
GND_LVDS2
13
LVDSB_CLKN
14
GND_LVDS2
15
GND_LVDS2
16
PANEL1_BACKLIGHT
15
GND_LVDS2
16
PANEL1_BACKLIGHT
17
LVDS2_TXL2P
18
PANEL1_BACKLIGHT
17
LVDSB_TXL2P
18
PANEL1_BACKLIGHT
19
LVDS2_TXL2N
20
GND_LVDS2
19
LVDSB_TXL2N
20
GND_LVDS2
45
SC_DDC
Pin
SC_DDC
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
1
Definition
1
SD_DDC
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 2: Jumpers and Connectors
Touch Panel Connector
Panel Power Connector
Connector type: 1x5 5-pin boxed header, JST 2.5mm
Connector location: USB1
Connector type: 1x5 5-pin boxed header, JST 2.5mm
Connector location: J1
1
5
Pin
1
5
Pin
Definition
1
Definition
VCC5
1
LIGHT CONTROLLER
2
USB4-
2
GND
3
USB4+
3
PANEL1_BACKLIGHT
4
GND
4
GND
5
GND
5
BACKLIGHT ENABLE
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
46
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 2: Jumpers and Connectors
USB Connector
HDD Power Connector
Connector type: 1x4 4-pin header, 2.54 mm pitch
Connector location: USB2
Connector type: 1x4 4-pin Wafer, 2.54 mm pitch
Connector location: CON1
1
4
1
4
Pin
Definition
1
VCC5
2
USB5-
Pin
3
USB5+
1
+12V
4
GND
2
GND
3
GND
4
VCC5
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
47
Definition
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 2: Jumpers and Connectors
Audio Connector
Fan Connector
Connector type:2x4 8-pin header, 2.54 mm pitch
Connector location: JP1
Connector type: 1x3 3-pin Wafer, 2.54 mm pitch
Connector location: FAN1
2
1
1
8
7
Pin
3
Definition
Pin
Definition
1
FRONT_L+
2
MIC1_L3
Pin
3
FRONT_L-
4
MIC_JD
1
GND
+12V
SYS FAN IN
5
FRONT_R+
6
NC
2
7
FRONT_R-
8
MIC1_R3
3
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
48
Definition
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 2: Jumpers and Connectors
COM3 Connector
COM4 Connector
Connector type:2x5 10-pin boxed header, 2.0 mm
Connector location: COM3
Connector type:2x5 10-pin boxed header, 2.0 mm
Connector location: COM4
2
1
2
1
10
9
Pin
Definition
Pin
Definition
10
9
Pin
2
Definition
2
SP_RXD3
3
SP_TXD3
4
SP_DTR3#
3
SP_TXD4
4
SP_DTR4#
5
COM3/4_GND
6
SP_DSR3#
5
COM3/4_GND
6
SP_DSR4#
7
SP_RTS3#
8
SP_CTS3#
7
SP_RTS3#
8
SP_CTS4#
9
SP_RI3#
10
COM3/4_GND
9
SP_RI4#
10
COM3/4_GND
49
SP_DCD4#
Pin
SP_DCD3#
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
1
Definition
1
SP_RXD4
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 2: Jumpers and Connectors
GPIO Connector
(4 digital input and 4 digital output)
LAN LED Connector
Connector type:2x4 8-pin header, 2.54 mm
Connector location: JP2
Connector type:2x5 10-pin header, 2.54 mm
Connector location: DIO1
1
2
9
10
Pin
2
1
8
7
Pin
1
Definition
Pin
Definition
1
VCC5
2
GND
3
SIO_GPO60
4
SIO_GPI64
5
SIO_GPO61
6
SIO_GPI65
7
SIO_GPO62
8
SIO_GPI66
9
SIO_GPO63
10
SIO_GPI67
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
50
Definition
3VSB
Pin
2
Definition
LAN1_ACT#
3
3VSB
4
LAN1_LINK#
5
3VSB
6
LAN2_ACT#
7
3VSB
8
LAN2_LINK#
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 2: Jumpers and Connectors
LAN LED Connector
SW Connector
Connector type:2x3 6-pin header, 2.0 mm
Connector location: JP3
Connector type:1x2 2-pin header, JST 2.5 mm pitch
Connector location: J2
2
1
1
6
5
Pin
Definition
Pin
GND
2
VCC5
3
HDD_LED#
4
VCC5
5
GND
6
LIGH CON
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
Pin
Definition
1
2
51
Definition
1
VIN
2
GND
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 2: Jumpers and Connectors
SATA DOM Power Connector
SATA Port
Connector type:1x2 2-pin header, JST 2.5 mm pitch
Connector location: J3
Connector type: Standard Serial ATAII 7P (1.27mm, SATA-M-180)
Connector location: CN4
1
2
Pin
7
1
Definition
1
VCC5
2
GND
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
Pin
52
Definition
1
GND
2
TXP0
3
TXN0
4
GND
5
RXN0
6
RXP0
7
GND
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 2: Jumpers and Connectors
SATA Port
Connector type: Standard Serial ATAII 7P (1.27mm, SATA-M-180)
Connector location: CN5
7
1
Pin
Definition
1
GND
2
TXP1
3
TXN1
4
GND
5
RXN1
6
RXP1
7
GND
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
53
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 2: Jumpers and Connectors
CompactFlash
Pin
Connector type: CompactFlash Type 2
Connector location: CF1
29
IDE_DD13
30
IDE_DD14
31
IDE_DD15
32
IDE_DCS3#
33
NC
34
IDE_DIOR#
35
IDE_DIOW#
36
VCC5
37
ICH_IDE_IRQ
38
VCC5
39
CF_SEL#
40
NC
41
IDE_RST#
42
IDE_IORDY
43
IDE_DDREQ
44
IDE_DDACK#
45
IDE_ACT#
46
IDE_66DET
Description
47
IDE_DD8
48
IDE_DD9
49
IDE_DD10
50
GND
Pin
Description
Pin
1
GND
2
IDE_DD3
3
ODEDD4
4
IDE_DD5
5
IDE_DD5
6
IDE_DD7
7
IDE_CS1#
8
GND
9
GND
10
GND
11
GND
12
GND
13
VCC5
14
GND
15
GND
16
GND
17
GND
18
IDE_DA2
19
IDE_DA1
20
IDE_DA0
21
IDE_DD0
22
IDE_DD1
23
IDE_DD2
24
NC
25
CF_CD2#
26
CF_CD1#
27
IDE_DD11
28
IDE_DD12
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
54
Description
Pin
Description
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 2: Jumpers and Connectors
Mini-PCIe Slots
Pin
Connector location: CN6
31
1
51
2
52
Pin
Definition
Pin
Definition
Pin
Definition
PET_N2
Definition
32
SMB_DATA_REAUME
33
PET_P2
34
GND
35
GND
36
USB_6N
37
GND
38
USB_6P
39
+V3.3A_MINI
40
GND
41
+V3.3A_MINI
42
NC
43
GND
44
LED_WLAN_N
45
NC
46
NC
47
NC
48
+V1.5S_MINI
49
NC
50
GND
51
NC
52
+V3.3A_MINI
1
PCIE_WAKE#
2
+V3.3A_MINI
3
NC
4
GND
MH1
GND
MH2
GND
GND
MH4
GND
GND
5
NC
6
+V1.5S_MINI
MH3
7
PCIE_MINI_CLKREQ#1
8
NC
MH6
9
GND
10
NC
11
CK_MiniPCIE#
12
NC
13
CK_MiniPCIE
14
NC
15
GND
16
NC
17
NC
18
GND
19
NC
20
MINICARD1_DIS#
21
GND
22
PLT_RST_BUF2#
23
PER_N2
24
+V3.3A_MINI
25
PER_P2
26
GND
27
GND
28
+V1.5S_MINI
29
GND
30
SMB_CLK_RESUME
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
55
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 2: Jumpers and Connectors
Mini-PCIe Slots
Pin
Connector location: CN7
31
1
51
2
52
Pin
Definition
Pin
Pin
Definition
PET_N3
Definition
32
SMB_DATA_REAUME
33
PET_P3
34
GND
35
GND
36
USB_7N
37
GND
38
USB_7P
39
+V3.3A_MINI2
40
GND
41
+V3.3A_MINI2
42
NC
43
GND
44
LED_WLAN2_N
45
NC
46
NC
47
NC
48
+V1.5S_MINI2
Definition
49
NC
50
GND
51
NC
52
+V3.3A_MINI2
1
PCIE_WAKE#
2
+V3.3A_MINI2
3
NC
4
GND
MH1
GND
MH2
GND
GND
MH4
GND
GND
5
NC
6
+V1.5S_MINI2
MH3
7
PCIE_MINI2_CLKREQ#
8
NC
MH6
9
GND
10
NC
11
CK_MiniPCIE2#
12
NC
13
CK_MiniPCIE2
14
NC
15
GND
16
NC
17
NC
18
GND
19
NC
20
MINICARD2_DIS#
21
GND
22
PLT_RST_BUF2#
23
PER_N3
24
+V3.3A_MINI2
25
PER_P3
26
GND
27
GND
28
+V1.5S_MINI2
29
GND
30
SMB_CLK_RESUME
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
56
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 3: BIOS Setup
Chapter 3: BIOS Setup
This chapter describes how to use the BIOS setup program for APPC
Series. The BIOS screens in this chapter are for reference only and may
change if the BIOS is updated in the future.
The settings made in the setup program intimately affect how the computer performs. It is important, therefore, first to try to understand all the
Setup options, and second, to make settings appropriate for the way you
use the computer.
To check for the latest updates and revisions, visit the NEXCOM Web site
at www.nexcom.com.tw.
When to Configure the BIOS
About BIOS Setup
This program should be executed under the following conditions:
The BIOS (Basic Input and Output System) Setup program is a menu driven utility that enables you to make changes to the system configuration
and tailor your system to suit your individual work needs. It is a ROMbased configuration utility that displays the system’s configuration status
and provides you with a tool to set system parameters.
• When changing the system configuration
• When a configuration error is detected by the system and you are
prompted to make changes to the Setup program
• When resetting the system clock
• When redefining the communication ports to prevent any conflicts
These parameters are stored in non-volatile battery-backed-up CMOS
RAM that saves this information even when the power is turned off.
When the system is turned back on, the system is configured with the
values found in CMOS.
• When making changes to the Power Management configuration
• When changing the password or making other changes to the security
setup
Normally, CMOS setup is needed when the system hardware is not consistent with the information contained in the CMOS RAM, whenever the
CMOS RAM has lost power, or the system features need to be changed.
With easy-to-use pull down menus, you can configure such items as:
• Hard drives, diskette drives, and peripherals
• Video display type and display options
• Password protection from unauthorized use
• Power management features
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
57
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 3: BIOS Setup
Entering Setup
BIOS Main Menu
When the system is powered on, the BIOS will enter the Power-On Self
Test (POST) routines. These routines perform various diagnostic checks; if
an error is encountered, the error will be reported in one of two different
ways:
Once you enter Award BIOS CMOS Setup Utility, the Main Menu will appear on screen. The main menu allows you to select from eight setup functions and two exit choices. Use the arrow keys to select among the items
and press <Enter> to accept or enter the sub-menu.
• If the error occurs before the display device is initialized, a series of
beeps will be transmitted.
Phoenix - AwardBIOS CMOS Setup Utility

Standard
• If the error occurs after the display device is initialized, the screen will
display the error message.
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.

PC Health Status
Load Optimized Defaults

Integrated
Peripherals
Set Password
Management Setup
Save & Exit Setup
Exit Without Saving

PnP/PCI
Configurations
Esc : Quit
F10 : Save & Exit Setup
TO ENTER SETUP BEFORE BOOT
PRESS <CTRL-ALT-ESC>
Press the <Del> key to enter Setup:
BIOS Features

Power
Powering on the computer and immediately pressing <Del> allows you to
enter Setup. Another way to enter Setup is to power on the computer and
wait for the following message during the POST:
CMOS Features

Advanced
↑ ↓ → ←:
Select Item
Time, Date, Hard Disk Type...
58
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 3: BIOS Setup
Getting Help
The following table lists the available options on the main menu.
Menu
The BIOS Setup program provides descriptions of the options available on
the menu.
Description
Standard CMOS
Features
Use this menu for basic system configuration.
Advanced BIOS
Features
Use this menu to set the advanced features available on the system.
Integrated
Peripherals
Use this menu to specify your settings for integrated peripherals.
Power
Management Setup
Use this menu to specify your settings for power
management.
PnP/PCI
Configurations
Appears if your system supports Plug and Play and
PCI Configuration.
PC Health Status
Displays CPU, System Temperature, Fan Speed,
and System Voltages Value.
Load Optimized
Defaults
Use this menu to load the BIOS default values,
that is, factory settings for optimum system performance. While Award has designed the custom
BIOS to maximize performance, the factory has
the option to change these defaults to meet their
needs.
Set Password
Enables you to change, set, or disable the supervisor or user password.
Save & Exit Setup
Saves CMOS value changes to CMOS and exits
setup
Exit Without Saving
Ignores all CMOS value changes and exits setup.
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
• If you are on the main menu, a description of the highlighted option can
be found at the bottom of the screen.
• If you are on the Status Page or Option Page setup menu, a description
of the highlighted option can be found on the right side of the screen
under the heading Item Help.
59
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 3: BIOS Setup
Using the Control Keys
The table below lists the keys that help you navigate the setup program.
Use This Key
To Do This
Up arrow
Move to previous item
Down arrow
Move to next item
Left arrow
Move to the item to the left
Right arrow
Move to the item to the right
Esc key
Main Menu: Quit without saving changes to CMOS
Status
Option Page Setup Menus: Exit current page and
return to Main Menu.
Enter Key
Select or Accept an Item
PgUp/plus key
Increase the numeric value or make changes
PgDn/minus key
Decrease the numeric value or make changes
F1 key
General help, only for Status Page Setup Menu and
Option Page Setup Menu
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
60
Use This Key
To Do This
F2/Shift + F2 key
Change color from total 16 colors. F2 to select color
forward, (Shift) F2 to select color backward
F5 key
Restore the previous CMOS value from CMOS (only
for Option Page Setup Menu)
F6 key
Load the default CMOS value from BIOS default
table (only for Option Page Setup Menu)
F7 key
Load the Setup default value (only for Option Page
Setup Menu)
F9 Key
Menu in BIOS
F10 key
Save all the CMOS changes (only for Main Menu)
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 3: BIOS Setup
BIOS Setup Utility
IDE Channel 0 Master and IDE Channel 2 Slave
Standard CMOS Features
To configure the IDE drives, move the cursor to a field then press <Enter>. The following screen will appear.
Phoenix - AwardBIOS CMOS Setup Utility
Standard CMOS Features
Date (mm:dd:yy)
Time (hh:mm:ss)
Thu, Nov 12 2009
16 : 27 : 53

IDE

IDE

IDE

IDE
[None]
[None]
[None]
[None]
Channel
Channel
Channel
Channel
0
0
2
2
Master
Slave
Master
Slave
Video
Halt On
Base Memory
Extended Memory
Total Memory
Phoenix - AwardBIOS CMOS Setup Utility
IDE Channel 0 Master
Item Help
Menu Level

Change the day, month,
year and century
IDE HDD Auto-Detection
[Press Enter]
IDE Channel 0 Master
Access Mode
Auto
Auto
Capacity
[EGA/VGA]
[All, But Keyboard]
639K
913408K
914432K
Cylinder
Head
Precomp
Landing Zone
Sector
↑↓→←:
↑↓→←:
Move
Enter: Select
+/-/PU/PD: Value
F5: Previous Values
F10: Save
ESC: Exit
F7: Optimized Defaults
F1: General Help
Enter: Select
+/-/PU/PD: Value
F5: Previous Values

To auto-detect the
HDD’s size, head... on
this channel
F10: Save
ESC: Exit
F7: Optimized Defaults
F1: General Help
IDE HDD Auto-Detection
Date
Detects the parameters of the drive. The parameters will automatically be shown on the screen.
The date format is <day>, <month>, <date>, <year>. Day displays a day,
from Sunday to Saturday. Month displays the month, from January to December. Date displays the date, from 1 to 31. Year displays the year, from
1999 to 2099.
IDE Channel 0 Master / IDE Channel 0 Slave
If you select ”Auto”, the BIOS will auto-detect the HDD & CD-ROM
drive at the POST stage and show the IDE for the HDD & CD-ROM
drive. If a hard disk has not been installed, select “None”.
Time
The time format is <hour>, <minute>, <second>. The time is based on
the 24-hour military-time clock. For example, 1 p.m. is 13:00:00. Hour
displays hours from 00 to 23. Minute displays minutes from 00 to 59.
Second displays seconds from 00 to 59.
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
Move
0 MB
0
0
0
0
0
Item Help
Menu Level
61
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 3: BIOS Setup
Access Mode
Video
For hard drives larger than 528MB, you would typically select the LBA
type. Certain operating systems require that you select CHS or Large.
Please check your operating system’s manual or Help desk on which
one to select.
This field selects the type of video adapter used for the primary system
monitor. Although secondary monitors are supported, you do not have to
select the type. The default setting is EGA/VGA.
EGA/VGA
Enhanced Graphics Adapter/Video Graphics Array. For EGA, VGA,
SVGA and PGA monitor adapters.
Capacity
Displays the approximate capacity of the disk drive. Usually the size
is slightly greater than the size of a formatted disk given by a disk
checking program.
CGA 40
Color Graphics Adapter. Power up in 40-column mode.
CGA 80
Color Graphics Adapter. Power up in 80-column mode.
Cylinder
Mono
Monochrome adapter. Includes high resolution monochrome adapters.
This field displays the number of cylinders.
Head
This field displays the number of read/write heads.
Halt On
Precomp
This field determines whether the system will stop if an error is detected
during power up. The default setting is All Errors.
This field displays the number of cylinders at which to change the
write timing.
No Errors
The system boot will not stop for any errors detected.
Landing Zone
All Errors
The system boot will stop whenever the BIOS detects a non-fatal error.
This field displays the number of cylinders specified as the landing
zone for the read/write heads.
All, But Keyboard
The system boot will not stop for a keyboard error; it will stop for all
other errors.
Sector
This field displays the number sectors per track.
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
62
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 3: BIOS Setup
Base Memory
Displays the amount of base (or conventional) memory installed in the
system. The value of the base memory is typically 512K for systems with
512K memory installed on the motherboard or 640K for systems with
640K or more memory installed on the motherboard.
Extended Memory
Displays the amount of extended memory detected during boot-up.
Total Memory
Displays the total memory available in the system.
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
63
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 3: BIOS Setup
Advanced BIOS Features
Hard Disk Boot Priority
This field is used to select the boot sequence of the hard drives. Move
the cursor to this field then press <Enter>. Use the Up or Down arrow
keys to select a device then press <+> to move it up or <-> to move it
down the list.
Phoenix - AwardBIOS CMOS Setup Utility
Advanced BIOS Features

Hard
Disk Boot Priority
First Boot Device
Second Boot Device
Third Boot Device
Security Option
** VGA Setting **
On-Chip Frame Buffer Size
Boot Display
Init Display First
Panel Number
↑↓→←:
Move
Item Help
Press Enter
USB-FDD
USB-CDROM
Hard Disk
Setup
Menu Level

Select Hard Disk Boot
Device Priority
Phoenix - AwardBIOS CMOS Setup Utility
Hard Disk Boot Priority
8MB
CRT
Onboard
1024x768 18bit S
Enter: Select
+/-/PU/PD: Value
F5: Previous Values
F10: Save
ESC: Exit
F7: Optimized Defaults
Item Help
1. Bootable Add-in Cards
Menu Level
F1: General Help
↑↓:
Move
PU/PD/+/-: Change Priority
F5: Previous Values
F6: Fail-Safe Defaults
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.

64
F10: Save
ESC: Exit
F7: Optimized Defaults
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 3: BIOS Setup
First Boot Device, Second Boot Device and Third Boot Device
On-Chip Frame Buffer Size
Select the drive to boot first, second and third in the “First Boot Device”
“Second Boot Device” and “Third Boot Device” fields respectively. The
BIOS will boot the operating system according to the sequence of the
drive selected.
This field is used to select the onboard VGA’s frame buffer size that is
shared from the system memory.
The options are:
1MB
8MB
The options are:
Hard Disk
CDROM
USB-FDD
USB-ZIP
USB-CDROM
LAN
Disabled
Boot Display
This field is used to select the type of display to use when the system
boots.
CRT1
LFP
CRT1 + LFP
CRT2
CRT1 + CRT2
DVI
CRT1+DVI
Security Option
This field determines when the system will prompt for the password everytime the system boots or only when you enter the BIOS setup. Set
the password in the Set Supervisor/User Password submenu.
System
The system will not boot and access to Setup will be denied unless
the correct password is entered at the prompt.
Setup
The system will boot, but access to Setup will be denied unless the
correct password is entered at the prompt.
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
65
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 3: BIOS Setup
Init Display First
Onboard
When the system boots, it will first initialize the onboard VGA.
PCI Slot
When the system boots, it will first initialize PCI.
Panel Number
This field is used to select the type of panel that you are using. The options are:
640x480 18bit S
800x600 18bit S
1024x768 18bit S
1280x1024 18bit D
1400x1050 18bit D
1280x800 24bit D
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
66
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 3: BIOS Setup
Integrated Peripherals
OnChip IDE Device
Move the cursor to this field and press <Enter>. The following screen will
appear.
Phoenix - AwardBIOS CMOS Setup Utility
Integrated Peripherals

OnChip
IDE Device
Azalia Audio
Onboard LAN Boot ROM
Onboard Serial Port 1
Onboard Serial Port 2
Onboard Serial Port 3

USB Device Setting
↑↓→←:
Move
Press Enter
Enabled
Disabled
3F8/IRQ4
2F8/IRQ3
3E8/IRQ4
Press Enter
Enter: Select
+/-/PU/PD: Value
F5: Previous Values
Item Help
Menu Level
F10: Save
ESC: Exit
F7: Optimized Defaults
Phoenix - AwardBIOS CMOS Setup Utility
OnChip IDE Device

IDE HDD Block Mode
On-Chip Primary PCI IDE
IDE Primary Master PIO
IDE Primary Slave PIO
IDE Primary Master UDMA
IDE Primary Slave UDMA
Enabled
Enabled
Auto
Auto
Auto
Auto
x
*** On-Chip Serial ATA Setting ***
On-Chip Serial ATA
PATA IDE Mode
SATA Port
Enhanced Mode
Secondary
P0, P2 is Primary
Item Help
Menu Level

If your IDE hard drive
supports block mode
select Enabled for automatic direction of
the optimal number of
block read/writes per
sector the drive can
support
F1: General Help
↑↓→←:
Move
Enter: Select
+/-/PU/PD: Value
F5: Previous Values
F10: Save
ESC: Exit
F7: Optimized Defaults
F1: General Help
IDE HDD Block Mode
Enabled
The IDE HDD uses the block mode. The system BIOS will check the
hard disk drive for the maximum block size the system can transfer.
The block size will depend on the type of hard disk drive.
Disabled
The IDE HDD uses the standard mode.
On-Chip Primary PCI IDE
Enables or disables the primary IDE. The default is Enabled. Select
Disabled if you want to add a different hard drive controller.
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
67
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 3: BIOS Setup
IDE Primary Master PIO and IDE Primary Slave PIO
On-Chip Serial ATA
Disabled
Disables the onboard SATA.
PIO means Programmed Input/Output. Rather than have the BIOS issue
a series of commands to effect a transfer to or from the disk drive, PIO
allows the BIOS to tell the controller what it wants and then let the
controller and the CPU perform the complete task by themselves. Your
system supports five modes, 0 (default) to 4, which primarily differ in
timing. When Auto is selected, the BIOS will select the best available
mode after checking your drive.
Combined Mode
PATA and SATA are combined. Maximum of 2 IDE drives in each
channel.
Enhanced Mode
Enables both SATA and PATA. Supports maximum of 5 IDE drives.
Auto
The BIOS will automatically set the system according to your hard
disk drive’s timing.
SATA Only
This option automatically sets the SATA drives to Primary Master
mode. Since the SATA drives are in Master mode, you cannot set
the IDE drive to Master mode.
Mode 0-4
You can select a mode that matches your hard disk drive’s timing. Caution: Do not use the wrong setting or you will have drive
errors.
PATA IDE Mode
This field is used to select the function mode of the IDE 1 connector
and its relation to the SATA ports.
IDE Primary Master UDMA and IDE Primary Slave UDMA
Primary
IDE 1 serves as Primary Master and Primary Slave channel. SATA
2 and SATA 4 serve as Secondary Master and Secondary Slave
channel. SATA 1 and SATA 3 are disabled.
These fields allow you to set the Ultra DMA in use. When Auto is
selected, the BIOS will select the best available option after checking
your hard drive or CD-ROM.
Auto
The BIOS will automatically detect the settings for you.
Secondary
IDE 1 serves as Secondary Master and Secondary Slave channel.
SATA 1 and SATA 3 serve as Primary Master and Primary Slave
channel. SATA 2 and SATA 4 are disabled.
Disabled
The BIOS will not detect these categories.
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
68
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 3: BIOS Setup
SATA Port
If the “PATA IDE Mode” field is set to Primary, this field will show
“P1, P3 is Secondary”; meaning SATA 2 and SATA 4 are Secondary.
If the “PATA IDE Mode” field is set to Secondary, this field will show
“P0, P2 is Primary”; meaning SATA 1 and SATA 3 are Primary.
Azalia Audio
Enables or disables the Azalia audio controller.
Onboard LAN Boot ROM
Enable this field if you wish to use the boot ROM (instead of a disk drive)
to boot-up the system and access the local area network directly.
If you wish to change the boot ROM’s settings, type the <Shift> and
<F10> keys simultaneously when prompted during boot-up. Take note:
you will be able to access the boot ROM’s program (by typing <Shift> +
<F10>) only when this field is enabled.
Onboard Serial Port 1 to Onboard Serial Port 3
3F8/IRQ4, 2F8/IRQ3, 3E8/IRQ4, 2E8/IRQ3, 2E0/IRQ4
Allows you to manually select an I/O address for the serial port.
Disabled
Disables the serial port.
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
69
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 3: BIOS Setup
USB Device Setting
USB Keyboard Function
Due to the limited space of the BIOS ROM, the support for legacy
USB keyboard (in DOS mode) is by default set to Disabled. With more
BIOS ROM space available, it will be able to support more advanced
features as well as provide compatibility to a wide variety of peripheral devices.
Phoenix - AwardBIOS CMOS Setup Utility
USB Device Setting
USB 1.0 Controller
USB 2.0 Controller
USB Keyboard Function
USB Storage Function
Enabled
Enabled
Enabled
Enalbed
Item Help
Menu Level

[Enable] or [Disable]
Universal Host
Controller Interface
for Universal Serial
Bus.
If a PS/2 keyboard is not available and you need to use a USB keyboard to install Windows (installation is performed in DOS mode) or
run any program under DOS, set this field to Enabled.
USB Storage Function
↑↓→←:
Move
Enter: Select
+/-/PU/PD: Value
F5: Previous Values
This field is used to enable or disable the support for legacy USB
mass storage.
F10: Save
ESC: Exit
F1: General Help
F7: Optimized Defaults
USB 1.0 Controller
This field is used to enable or disable the Universal Host Controller
Interface (USB 1.0).
USB 2.0 Controller
This field is used to enable or disable the Enhanced Host Controller
Interface (USB 2.0).
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
70
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 3: BIOS Setup
Power Management Setup
Power Supply Type
Power Management Setup lets you control the system power. The system
has various power-saving modes — including powering down the hard
disk, turning off the video, suspending to RAM, and software power down
— that allows the system to automatically resume by certain events.
This field is used to select the type of power supply used.
PWRON After PWR-Fail
Off
When power returns after an AC power failure, the system’s power is
off. You must press the Power button to power-on the system.
The power-saving modes can be controlled by timeouts. If the system is
inactive for a time, the timeouts begin counting. If inactivity continues
and reaches the defined timeout period, the system enters a power saving
mode. If any item in the list of Reload Global Timer Events is enabled, then
any activity on that item will reset the timeout counters to zero.
On
When power returns after an AC power failure, the system will automatically power-on.
Former-Sts
When power returns after an AC power failure, the system will return
to the state where you left off before power failure occurs. If the
system’s power is off when AC power failure occurs, it will remain off
when power returns. If the system’s power is on when AC power failure occurs, the system will power-on when power returns.
If the system is suspended or has been powered down by software, it can
be resumed by a wake up call that is generated by incoming traffic to a
modem, a LAN card, a PCI card, or a fixed alarm on the system real-time
clock.
Phoenix - AwardBIOS CMOS Setup Utility
Power Management Setup
Power-Supply Type
PWRON After PWR-Fail
PCI Express PME
ACPI Function
Video Off Method
Video Off In Suspend
Soft-Off by PWR-BTTN
Power On by Ring
ATX
On
Disabled
Enabled
DPMS
Yes
Instant-Off
Enabled
PCI Express PME
Item Help
Menu Level

This field is used to configure the PCI Express PME.
ACPI Function
By default, the ACPI function is enabled. This function should be enabled
only in operating systems that support ACPI.
↑↓→←:
Move
Enter: Select
+/-/PU/PD: Value
F5: Previous Values
F10: Save
ESC: Exit
F7: Optimized Defaults
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
F1: General Help
71
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 3: BIOS Setup
Video Off Method
Soft-Off by PWR-BTTN
This determines the manner in which the monitor is blanked.
This field allows you to select the method of powering off your system.
V/H SYNC + Blank This selection will cause the system to turn off the vertical and horizontal synchronization ports and write blanks to the video buffer.
Delay 4 Sec.
Regardless of whether the Power Management function is enabled or
disabled, if the power button is pushed and released in less than 4 sec,
the system enters the Suspend mode. The purpose of this function is
to prevent the system from powering off in case you accidentally “hit”
or pushed the power button. Push and release again in less than 4
sec to restore. Pushing the power button for more than 4 seconds will
power off the system.
Blank Screen This option only writes blanks to the video buffer.
DPMS Support Initializes display power management signaling. Use this option if
your video board supports it.
Instant-Off
Pressing and then releasing the power button at once will immediately
power off your system.
Video Off In Suspend
This field is used to activate the video off feature when the system enters
the Suspend mode. The options are Yes and No.
Power On By Ring
Set this field to Enabled to use the modem ring-on function. This will allow your system to power-on to respond to calls coming from an external
modem.
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
72
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 3: BIOS Setup
PnP/PCI Configurations
Resources Controlled By
The Award Plug and Play BIOS has the capability to automatically configure all of the boot and Plug and Play compatible devices.
Phoenix - AwardBIOS CMOS Setup Utility
PnP/PCI Configurations
Reset Configuration Data
Resources Controlled By
x IRQ Resources
Disabled
Item Help
Menu Level
Auto(ESCD)
Press Enter
Auto(ESCD)
The system will automatically detect the settings for you.

Manual
Choose the specific IRQ resources in the “IRQ Resources” field.
IRQ Resources
Set each system interrupt to either PCI Device or Reserved.
↑↓→←:
Move
Enter: Select
+/-/PU/PD: Value
F5: Previous Values
F10: Save
ESC: Exit
F7: Optimized Defaults
Phoenix - AwardBIOS CMOS Setup Utility
IRQ Resources
F1: General Help
IRQ-3 assigned to
IRQ-4 assigned to
IRQ-5 assigned to
IRQ-7 assigned to
IRQ-9 assigned to
IRQ-10 assigned to
IRQ-11 assigned to
IRQ-12 assigned to
IRQ-14 assigned to
IRQ-15 assigned to
Reset Configuration Data
Enabled The BIOS will automatically reset the Extended System Configuration
Data (ESCD) once. It will then recreate a new set of configuration
data.
PCI
PCI
PCI
PCI
PCI
PCI
PCI
PCI
PCI
PCI
Device
Device
Device
Device
Device
Device
Device
Device
Device
Device
Item Help
Menu Level

Legacy ISA for devices
compliant with the
original PC AT bus
specification. PCI/ISA
PnP for devices
compliant with the
Plug and Play standard
whether designed for
PCI or ISA bus
architecture.
Disabled
The BIOS will not reset the configuration data.
↑↓→←:
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
73
Move
Enter: Select
+/-/PU/PD: Value
F5: Previous Values
F10: Save
ESC: Exit
F7: Optimized Defaults
F1: General Help
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 3: BIOS Setup
PC Health Status
Load Optimized Defaults
Phoenix - AwardBIOS CMOS Setup Utility
PC Health Status
Current System Temp
Current CPU Temperature
System Fan Speed
Vcore
+12 V
+1.5 V
+3.3 V
28OC/82OF
34OC/93OF
0 RPM
1.17V
11.80V
1.50V
3.28V
Phoenix - AwardBIOS CMOS Setup Utility
Item Help
Menu Level

Standard

CMOS Features

PC Health Status

Advanced
BIOS Features
Load Optimized Defaults

Integrated
Peripherals
Set Password
Management Setup
Save & Exit Setup

Power

PnP/PCI
Configurations
Load Optimized Defaults
(Y/N)?
N
Exit Without
Saving
Esc : Quit
F9 : Menu in BIOS
F10 : Save & Exit Setup
↑ ↓ → ←:
Select Item
Time, Date, Hard Disk Type...
↑↓→←:
Move
Enter: Select
F5: Previous Values
+/-/PU/PD: Value
F10: Save
F6: Fail-Safe Defaults
ESC: Exit
F1: General Help
F7: Optimized Defaults
This option opens a dialog box that lets you install optimized defaults for
all appropriate items in the whole setup utility. Press the <Y> key and then
<Enter> to install the defaults. Press the <N> key and then <Enter> if you
do not want to install the defaults. The optimized defaults place demands
on the system that may be greater than the performance level of the components, such as the CPU and the memory.
Current System Temp to +3.3V
These fields will show the temperature, fan speed and output voltages of
the monitored devices or components.
Fatal errors or instability may occur if you install the optimized defaults
when your hardware does not support them. If you only want to install
setup defaults for a specific option, select and display that option, and
then press the <F7> key.
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
74
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 3: BIOS Setup
Set Password
Save & Exit Setup
Phoenix - AwardBIOS CMOS Setup Utility

Standard
PC Health Status

Standard

Advanced
BIOS Features
Load Optimized Defaults

Advanced
BIOS Features
Load Optimized Defaults

Integrated
Peripherals
Set Password

Integrated
Peripherals
Set Password
Management Setup
Save & Exit Setup

Power
Management Setup
Save & Exit Setup
Exit Without Saving

PnP/PCI

Power

PnP/PCI
CMOS Features
Phoenix
Phoenix--AwardBIOS
AwardBIOSCMOS
CMOSSetup
SetupUtility
Utility
Configurations
Enter Password:
Esc : Quit
F9 : Menu in BIOS
F10 : Save & Exit Setup

↑ ↓ → ←:
Select Item
CMOS Features
Configurations

PC Health Status
Exit Without Saving
SAVE to CMOS and EXIT (Y/N)? Y:
Esc : Quit
F9 : Menu in BIOS
F10 : Save & Exit Setup
↑ ↓ → ←:
Select Item
Time, Date, Hard Disk Type...
Time, Date, Hard Disk Type...
The User Password utility sets the password. The main board is shipped
with the password disabled. If you want to change the password, you
must first enter the current password, then at the prompt enter your new
password. The password is case sensitive. You can use up to eight alphanumeric characters. Press <Enter> after entering the password. At the next
prompt, confirm the new password by retyping it and pressing <Enter>
again.
Selecting this option and pressing <Enter> will save the new setting information in the CMOS memory and continue with the bootup process.
To disable the password function, highlight “Set Password” then press
<Enter>, instead of typing in a new password. A message appears confirming that the password has been disabled. If you have set supervisor
and user Password, only the supervisor password allows you to enter the
BIOS setup program.
Note: If you forgot your password, the only way to solve this problem is
to discharge the CMOS memory by turning power off and placing a shunt
(jumper cap) on the RTC Clear jumper to short pin 2 and pin 3 for five
seconds, then putting the shunt back to pin 1 and pin 2.
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
75
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Chapter 3: BIOS Setup
Exit Without Saving
Phoenix
Phoenix--AwardBIOS
AwardBIOSCMOS
CMOSSetup
SetupUtility
Utility

Standard
CMOS Features

PC Health Status

Advanced
BIOS Features
Load Optimized Defaults

Integrated
Peripherals
Set Password
Management Setup
Save & Exit Setup

Power

PnP/PCI
Configurations
Exit Without Saving
Quit Without Saving (Y/N)? N:
Esc : Quit
F9 : Menu in BIOS
F10 : Save & Exit Setup
↑ ↓ → ←:
Select Item
Time, Date, Hard Disk Type...
Selecting this option and pressing <Enter> will exit the Setup utility without recording any new values or changing old ones.
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
76
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Appendix A: Watchdog Timer
Appendix A: Watchdog Timer
WDT Programming Guide
Watch Dog Sample Code
APPC Series Watchdog Function Configuration Sequence Description:
===============================================
SetupWDT
PROC
mov
dx, 2eh
mov
al, 087h
out
dx, al
nop
nop
out
dx, al
Start
Step 1
See “SetupWDT” procedure
#Setup Watchdog Timer Environment
Step 2
mov
out
mov
out
ret
SetupWDT
See “TimeBaseWDT” procedure
#Initial Watchdog Timer
Users can select second or minute
Step 3
See “TimeCountWDT” procedure
#Set Watchdog Timer Time-out Value
Users can set time-out value
al, 07h
2eh, al
al, 08h ;Select logical device for Watch Dog.
2fh, al
ENDP
===============================================
TimeBaseWDT
PROC
mov
al, 0F5h
out
2eh, al
mov
al, 02h ;Set WDT reset upon KBRST#
or
al, 00h ;Here!! set 00h for second, set 08h for minute
out
2fh, al
Step 4
See ExitSetup procedure
#Exit Setup Environment
End
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
77
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Appendix A: Watchdog Timer
ret
TimeBaseWDT
ENDP
===============================================
TimeCountWDT PROC
mov
al, 0F6h ;WDT Time-out register.
out
2eh, al
mov
al, 03h ;Here!! Set count 3.
out
2fh, al
ret
TimeCountWDT ENDP
===============================================
ExitSetup
PROC
mov
dx, 2eh
mov
al, 0AAh
out
dx, al
ExitSetup
ENDP
===============================================
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
78
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Appendix B: GPI/O Programming Guide
Appendix B: GPI/O Programming Guide
I/O Base Address: 800h
This appendix provides definitions for the GPI/O pins on APPC Series.
GPI/O (General Purpose Input/Output) pins are provided for custom system
design. The pin programmed as input mode (GPI) or output mode (GPO)
depends on the configuration.
Bit0 : GPI 50
Bit1 : GPI 51
Bit2 : GPI 52
Bit3 : GPI 53
Bit4 : GPO 54
Bit5 : GPO 55
Bit6 : GPO 56
Bit7 : GPO 57
GPIO
Pin
Description
Pin
Pin 9
1
+5V
2
GND
3
GPO54
4
GPI50
5
GPO55
6
GPI51
7
GPO56
8
GPI52
9
GPO57
10
GPI53
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
1. Select GPIO group5 by setting I/O port 800h to 5h.
2. Read/Write GPIO data by I/O port 802h.
79
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Appendix C: Power Consumption
Appendix C: Power Consumption
Power Consumption Measurement - APPC 0810T
Low AC Line 110~115V (System Only)
12V
Total(W)
S1 (Power On Suspend)
0.75A
9.00W
Light-Loading Mode (A/W)
1.02A
12.24W
Full-Loading Mode (A/W)
1.22A
14.64W
Power Consumption Measurement - APPC 1210T/1211T/1510T/1511T
Power Type
DC-in 12-30V
Consumed Watts (W)
82.6
Consumed Currents (Item A)
9.2
Actual Required Currents (Item A/0.80 )
11.5
Actual Required Watt (W)
103.25
Copyright © 2010 NEXCOM International Co., Ltd. All Rights Reserved.
80
APPC 0810T/1210T/1211T/1510T/1511T User Manual
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising