Manual 12660750
E L A TI ON | PLATINUM BEAM 5R EXTREME™ | user manual 1.0
PLATINUM BEAM 5R EXTREME™
user manual 1.0 www.elationlighting.com
©2014 ELATION PROFESSIONAL all rights reserved. Information, specifications,
diagrams, images, and instructions herein are subject to change without notice.
ELATION PROFESSIONAL logo and identifying product names and numbers herein
are trademarks of ELATION PROFESSIONAL. Copyright protection claimed includes
all forms and matters of copyrightable materials and information now allowed by
statutory or judicial law or hereinafter granted. Product names used in this
document may be trademarks or registered trademarks of their respective
companies and are hereby acknowledged. All non-ELATION brands and product
names are trademarks or registered trademarks of their respective companies.
ELATION PROFESSIONAL and all affiliated companies hereby disclaim any and all
liabilities for property, equipment, building, and electrical damages, injuries to any
persons, and direct or indirect economic loss associated with the use or reliance of
any information contained within this document, and/or as a result of the improper,
unsafe, insufficient and negligent assembly, installation, rigging, and operation of
this product.
Elation Professional USA | 6122 S. Eastern Ave. | Los Angeles, CA. 90040
323-582-3322 | 323-832-9142 fax | www.elationlighting.com | info@elationlighting.com
Elation Professional B.V. | Junostraat 2 | 6468 EW Kerkrade, Netherlands
+31 45 546 85 66 | +31 45 546 85 96 fax | www.elationlighting.eu | info@elationlighting.eu
2
PLATINUM BEAM 5R EXTREME™ User Manual 1.0
www.elationlighting.com
CONTENTS
General Information
4
Warranty
6
Safety Instructions
7
General Guidelines
8
Discharge Lamp Warning
9
Fixture Overview
10
Lamp Installation Instructions
11
Fixture Installation
19
Understanding DMX
22
Fixture Menu
26
EWDMX Wireless DMX Receiver Set Up
36
DMX Channel Functions And Values
38
Error Codes
41
Cleaning and Maintenance
43
Technical Specifications
44
Optional Accessories
47
cETLus Approval Mark
47
3
PLATINUM BEAM 5R EXTREME™ User Manual 1.0
www.elationlighting.com
GENERAL INFORMATION
INTRODUCTION
Congratulations, you have just purchased one of the most innovative and
reliable lighting fixtures on the market today! The PLATINUM BEAM 5R EXTREME™
has been designed to perform reliably for years when the guidelines in this
booklet are followed. Please read and understand the instructions in this manual
carefully and thoroughly before attempting to operate this unit. These instructions
contain important information regarding safety during use and maintenance.
UNPACKING
Thank you for purchasing the PLATINUM BEAM 5R EXTREME™ by Elation
Professional®. Every PLATINUM BEAM 5R EXTREME™ has been thoroughly tested
and has been shipped in perfect operating condition. Carefully check the
shipping carton for damage that may have occurred during shipping. If the
carton appears to be damaged, carefully inspect your unit for
damage and
be sure all accessories necessary to operate the unit have arrived intact. In the
event damage has been found or parts are missing, please contact our
customer support team for further instructions. Please do not return this unit to
your dealer without first contacting customer support at the number listed below.
Please do not discard the shipping carton in the trash. Please recycle whenever
possible.
BOX CONTENTS
•
(2) Omega Brackets
•
(1) 3pin DMX Cable
•
(1) powerCON Cable
•
(1) Safety Cable
•
Manual & Warranty Card
M A N U A L
U P D A T E S
Please check www.elationlighting.com for the latest updated version of this manual.
4
PLATINUM BEAM 5R EXTREME™ User Manual 1.0
www.elationlighting.com
CUSTOMER SUPPORT
Elation Professional® provides a customer support line, to provide set up help and
to answer any question should you encounter problems during your set up or
initial operation. You may also visit us on the web at www.elationlighting.com for
any comments or suggestions. For service related issue please contact Elation
Professional®.
ELATION SERVICE USA - Monday - Friday 8:00am to 5:00pm PST
Voice: 323-582-3322
Fax: 323-832-9142
E-mail: support@elationlighting.com
ELATION SERVICE EUROPE - Monday - Friday 08:30 to 17:00 CET
Voice: +31 45 546 85 30
Fax: +31 45 546 85 96
E-mail: support@elationlighting.eu
WARRANTY REGISTRATION
The PLATINUM BEAM 5R EXTREME™ carries a two-year (730 days) limited warranty.
Please fill out the enclosed warranty card to validate your purchase. All returned
service items whether under warranty or not, must be freight pre-paid and
accompany a return authorization (R.A.) number. The R.A. number must be
clearly written on the outside of the return package. A brief description of the
problem as well as the R.A. number must also be written down on a piece of
paper and included in the shipping container. If the unit is under warranty, you
must provide a copy of your proof of purchase invoice. Items returned without a
R.A. number clearly marked on the outside of the package will be refused and
returned at customer’s expense. You may obtain a R.A. number by contacting
customer support.
IMPORTANT
NOTICE!
There are no user serviceable parts inside this unit. Do not attempt any repairs
yourself; doing so will void your manufactures warranty. Damages resulting from
modifications to this fixture and/or the disregard of safety and general user
instructions found in this user manual void the manufactures warranty and are
not subject to any warranty claims and/or repairs.
5
PLATINUM BEAM 5R EXTREME™ User Manual 1.0
www.elationlighting.com
2-YEAR LIMITED WARRANTY
A.
Elation Professional® hereby warrants, to the original purchaser, Elation Professional® products to
be free of manufacturing defects in material and workmanship for a period of two years, (730 days)
from the date of purchase. This warranty shall be valid only if the product is purchased within the
United States of America, including possessions and territories. It is the owner’s responsibility to
establish the date and place of purchase by acceptable evidence, at the time service is sought.
B.
For warranty service, send the product only to the Elation Professional® factory. All shipping
charges must be pre-paid. If the requested repairs or service (including parts replacement) are within
the terms of this warranty, Elation Professional® will pay return shipping charges only to a designated
point within the United States. If the entire instrument is sent, it must be shipped in its original package.
No accessories should be shipped with the product. If any accessories are shipped with the product,
Elation Professional® shall have no liability what so ever for loss of or damage to any such accessories,
nor for the safe return thereof.
C.
This warranty is void if the serial number has been altered or removed; if the product is modified
in any manner which Elation Professional® concludes, after inspection, affects the reliability of the
product; if the product has been repaired or serviced by anyone other than the Elation Professional®
factory unless prior written authorization was issued to purchaser by Elation Professional®; if the
product is damaged because not properly maintained as set forth in the instruction manual.
D.
This is not a service contract, and this warranty does not include maintenance, cleaning or
periodic check-up. During the period specified above, Elation Professional® will replace defective
parts at its expense, and will absorb all expenses for warranty service and repair labor by reason of
defects in material or workmanship.
The sole responsibility of Elation Professional® under this
warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the
sole discretion of Elation Professional®. All products covered by this warranty were manufactured
after January 1, 1990, and bare identifying marks to that effect.
E.
Elation Professional® reserves the right to make changes in design and/or improvements upon its
products without any obligation to include these changes in any products theretofore
manufactured.
F.
No warranty, whether expressed or implied, is given or made with respect to any accessory
supplied with products described above. Except to the extent prohibited by applicable law, all
implied warranties made by Elation Professional® in connection with this product, including
warranties of merchantability or fitness, are limited in duration to the warranty period set forth above.
And no warranties, whether expressed or implied, including warranties of merchantability or fitness,
shall apply to this product after said period has expired. The consumer’s and or Dealer’s sole remedy
shall be such repair or replacement as is expressly provided above; and under no circumstances shall
Elation Professional® be liable for any loss or damage, direct or consequential, arising out of the use
of, or inability to use, this product.
G.
This warranty is the only written warranty applicable to Elation Professional® Products and
supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore
published.
6
PLATINUM BEAM 5R EXTREME™ User Manual 1.0
www.elationlighting.com
SAFETY INSTRUCTIONS
The PLATINUM BEAM 5R EXTREME™ is an extremely sophisticated piece of
electronic equipment. To guarantee a smooth operation, it is important to
follow the guidelines in this manual. The manufacturer of this device will not
accept responsibility for damages resulting from the misuse of this fixture
due to the disregard of the information printed in this manual.
This device falls under PROTECTION CLASS 1. It’s essential this device be
grounded properly. Only qualified personnel should perform all electrical
connections.
•
For proper operation, follow the Installation guidelines described in this manual. Only qualified
and certified personnel should perform installation of this fixture and only the original rigging parts
(brackets) included with this fixture should be used for installation. Any modifications will void the
original manufactures warranty and increase the risk of damage and/or personal injury.
•
Never look directly into the light source of this fixture to prevent risk of injury to your retina, which
may induce blindness. Those suffering from EPILEPSY should avoid looking directly into the light
source of this unit at all times.
•
The fan and air inlets must remain clean and never blocked. Allow approx. 6” (15cm) between
this fixture and other devices or a wall for proper cooling.
•
Always disconnect from main power source before performing any type of service and/or
cleaning procedure. Only handle the power cord by the plug end, never pull out the plug by
tugging the wire portion of the cord.
•
Do not operate this fixture if the power cord has become frayed, crimped and/or damaged. If
the power cord is damaged, replace it immediately with a new one of similar power rating.
7
PLATINUM BEAM 5R EXTREME™ User Manual 1.0
www.elationlighting.com
GENERAL GUIDELINES
•
N E V E R
O P E N
T H I S
F I X T U R E
W H I L E
I N
U S E !
•
During the initial operation of this fixture, a light smoke or smell may emit from the
interior of the fixture. This is a normal process and is caused by excess paint in the
interior of the casing burning off from the heat associated with the lamp and will
decrease gradually over time.
•
This fixture is a professional lighting effect designed for INDOOR / DRY LOCATIONS
ONLY on stage, in nightclubs, theatres, etc.
•
Please make sure there are NO FLAMMABLE MATERIALS close to the fixture while
operating, to prevent any fire hazard.
•
The fixture must be installed in a location with adequate ventilation, at least 1.5
feet (.5m) from adjacent surfaces. Be sure no air ventilation slots are blocked.
•
DO NOT attempt installation and/or operation without knowledge how to do so.
•
DO NOT permit operation by persons who are not qualified to operate this type
of fixture. Most damages are the result of operations by nonprofessionals.
•
Consistent operational breaks may ensure the fixture will function properly for
many years to come.
•
DO NOT shake fixture, avoid brute force when installing and/or operating fixture.
•
Always install the fixture with an appropriate safety cable. When installing the
fixture in a suspended environment, always use mounting hardware that is no less
than M10 x 25 mm, also be sure the hardware is insert in the pre-arranged screw
holes in the bracket of the fixture.
•
Use the original packaging and materials to transport the fixture in for service.
•
DO NOT TOUCH the housing bare-hand during its operation. Turn OFF the power
and allow approximately 15 minutes for the fixture to cool down before replacing
or serving.
8
PLATINUM BEAM 5R EXTREME™ User Manual 1.0
www.elationlighting.com
DISCHARGE LAMP WARNING
This fixture is fitted with a DISCHARGE LAMP, which is highly
susceptible to damage if improperly handled. NEVER touch the
lamp with your bare hands, as the oil from your hands will shorten
the life of the lamp. Also, NEVER move the fixture until the lamp
has had ample time to cool. Lamps are NOT covered under
warranty conditions.
Avoid switching the fixture ON and OFF repeatedly in short
intervals, as this will reduce lamp life and intensity. To achieve the intensity
associated with discharge lamps, these lamps use gas sealed in a high-pressure
environment to emit a brilliant output.
Due to the high pressure involved with the construction of the lamp, the
lamp MAY EXPLODE DURING PROLONGED EXTENSIVE USE. This risk is increased with
age; added care is encouraged when dealing with older lamps. Thus, the lamp
must always be replaced at the end of their recommended duty cycle. Extreme
caution should be used when operating this or any fixture fitted with a gas
discharge lamp.
U V
R A D I A T I O N
N O T I C E
This fixture emits intense UV radiation, which is harmful to the
eyes and skin. The intense luminance of the lamp can cause
severe damage to the retina. NEVER operate this fixture with
ANY of the protective covers removed. These covers have
been specially designed to shield against UV radiation.
L A M P
R E P L A C E M E N T
Please note that due to the nature of the Phillips™ Platinum 5R
Lamp and the optical path of the Elation PLATINUM BEAM 5R
EXTREME fixture, the lamp MUST BE replaced at 2,000 hours.
Use only Genuine Original Phillips™ platinum lamps. Other
brand lamps may cause damage and void warranty!
9
PLATINUM BEAM 5R EXTREME™ User Manual 1.0
www.elationlighting.com
FIXTURE OVERVIEW
10
1.
LED Assembly
2.
LCD Menu Function Display
3.
Wireless DMX Indicator
4.
DC Switch
5.
Microphone
6.
LEFT Button
7.
DOWN Button
8.
RIGHT Button
9.
MODE/ESC Button
10.
UP Button
11.
ENTER Button
12.
Wireless DMX Antenna
13.
Carrying Handle(s)
14.
Lamp Access/Cover Panel
15.
3pin DMX Input
16.
3pin DMX Output
17.
5pin DMX Output
18.
5pin DMX Input
19.
powerCON Input
20.
Fuse
PLATINUM BEAM 5R EXTREME™ User Manual 1.0
www.elationlighting.com
LAMP INSTALLATION INSTRUCTIONS
L A M P
R E P L A C E M E N T
Please note that due to the nature of the Phillips™ Platinum 5R
Lamp and the optical path of the Elation PLATINUM BEAM 5R
EXTREME fixture, the lamp MUST BE replaced at 2,000 hours.
Use only Genuine Original Phillips™ Platinum 5R Lamps. Other
brand lamps may cause damage and void warranty!
INSTALLING OR REPLACING THE LAMP
To ensure a proper/safe lamp change, carefully read all the following instructions.
LAMP PROTECTION CIRCUITRY
Because of the nature of the extreme heat associated with the Phillips™ Platinum 5R
lamp and the tight nature of the internal optical system, it is IMPERATIVE that the
lamp be replaced every 2,000 Hours. This is done to protect the internal optical
system as well as prevent accidental lamp explosion, which could lead to hot glass
particles falling from the fixture.
FAILURE TO CHANGE THE LAMP WITHIN 300 HOUR of the 2,000 HOUR RATED
LIFE, WILL CAUSE THE FIXTURE TO AUTOMATICALLY SHUT DOWN!
At 2,000 Hours the LCD control display will begin to flash, “Replace The Lamp” and
the lamp will flicker for the first five minutes of operation. At this point the lamp has
reached the maximum rated life and should be replaced immediately. After the
lamp has flickered for about five minutes it should strike normally allowing the fixture
to be used temporarily until a replacement lamp can be installed. The fixture will
continue to operate for an additional 300 hours, however the “Replace the Lamp”
warning will continue to flash in the display. Keep in mind that the flicker protection
circuitry will only work for about 300 Hours (lamp clock life of 2,000-2,300 Hours).
After 2,300 Hours the fixture will no longer respond to DMX commands and
immediately enter a hibernation mode that will electronically discontinue all fixture
functionality with the exception of a few menu commands. The fixture will continue
to enter hibernation mode until the lamp is replaced and the lamp clock has been
reset. To replace the lamp follow the safety guidelines and procedures listed on the
next page.
11
PLATINUM BEAM 5R EXTREME™ User Manual 1.0
www.elationlighting.com
LAMP SAFETY INSTRUCTIONS
•
ALWAYS replace lamp every 2,000 Hours.
•
Use only Genuine Original Phillips™ Platinum 5R lamps. Other brand lamps may
cause damage and void the warranty!
•
NEVER touch the lamp with your bare hands, as the oil from your hands will
shorten the life of the lamp.
•
Always disconnect the fixture’s main power supply before replacing lamp.
•
Allow fixture to cool for at least 15 minutes before attempting any type of service.
•
Make sure ALL covers/panels are replaced/secured before operating the fixture
to prevent any risk and/or damage to eye retina from UV Radiation exposure!
LAMP INSTALLATION PROCEDURE
1. Place fixture on a flat surface and remove (4) screws marked “A”, “B”, “C”, and
“D” and then remove rear cover plate (see image below) to access the lamp.
LAMP COVER PLATE
12
PLATINUM BEAM 5R EXTREME™ User Manual 1.0
www.elationlighting.com
2. Gently remove (2) Red Wires connected to spade terminals on base of lamp.
3. Using two fingers on your RIGHT hand, pull the retention handle OUT and towards
the RIGHT as far as possible.
13
PLATINUM BEAM 5R EXTREME™ User Manual 1.0
www.elationlighting.com
4. While pulling the retention handle with your RIGHT hand, use your LEFT hand to
gently twist the lamp COUNTERCLOCKWISE to remove it from under the retention
brackets.
14
PLATINUM BEAM 5R EXTREME™ User Manual 1.0
www.elationlighting.com
5. Using two fingers on your RIGHT hand, pull the retention handle OUT and towards
the RIGHT as far as possible.
6. While pulling the retention handle with your RIGHT hand, use your LEFT had to
gently install the lamp under the retention brackets by holding the lamp at a
slight angle and positioning it until it is flush with the base.
15
PLATINUM BEAM 5R EXTREME™ User Manual 1.0
www.elationlighting.com
7. While still holding the retention handle with your RIGHT hand, gently turn the
lamp CLOCKWISE with your LEFT hand until the lamp is correctly aligned under
the retention brackets.
8. Release the retention handle with your RIGHT hand and make sure the handle is
upright and not at an angle.
16
PLATINUM BEAM 5R EXTREME™ User Manual 1.0
www.elationlighting.com
9. Gently attached (2) Red Wires connected to spade terminals on base of lamp.
10. Replace the lamp cover back into place by securing (4) screws marked “A”, “B”,
“C”, and “D”.
11. Be sure to reset the LAMP HOURS in the system menu to prevent the protection
circuitry from accidently shutting off the lamp during normal operation.
12. If the lamp protection circuitry has already been initiated and the LAMP HOURS is
not reset, the “Replace the Lamp” warning will continue to flash and fixture will
eventually shut down. To reset LAMP HOURS, see instructions on the next page.
17
PLATINUM BEAM 5R EXTREME™ User Manual 1.0
www.elationlighting.com
LAMP HOURS RESET PROCEDURE
1. Activate the main menu by pressing MODE/ESC and toggle to “Information”.
2. Press ENTER and press UP or DOWN to toggle to “Time Information”.
3. Press UP or DOWN to toggle to “L-Timer Password” and press ENTER. Then press UP
or DOWN to enter the reset pass code, “038” and press ENTER to confirm. The
display will automatically revert to “L-Timer Password”, next press UP or DOWN to
toggle down to “Clear Lamp Time”.
4. Press ENTER and select “ON”. The lamp timer has now been reset, press
MODE/ESC to exit the menu and return to the home screen.
LAMP OPTIMIZATION
Unlike traditional discharge lamps the Phillips™ Platinum 5R PRO Lamp does NOT
require optimization. The lamp orientation and optimization procedure has been
preset during the manufacturing process of the lamp.
Please remember the Phillips™ Platinum 5R PRO Lamp is NOT a hot-restrike lamp
therefore, you must wait approximately 15 minutes before you can attempt to
restrike the lamp once it has been turned off.
18
PLATINUM BEAM 5R EXTREME™ User Manual 1.0
www.elationlighting.com
FIXTURE INSTALLATION
T he el ec tri c c onnec ti on m ust onl y b e c arri ed out b y a qu al if i ed el ec tri c i an. CAUTIONS
•
For added protection, mount the fixture in areas outside walking paths, seating
areas, or in areas were unauthorized personnel might reach the fixture.
•
Ambient operating temperature range for this fixture is 14° to 113°F. (-10° to 45°C)
Do not use the fixture under or above this temperature.
•
Before mounting the fixture to any surface, make sure the installation area can
hold a minimum point load of 10 times the weight of the fixture. (419 lbs / 190 kg)
•
Fixture installation must always be secured with a secondary safety attachment,
such as an appropriate safety cable.
•
Never stand directly below the device when mounting, removing or servicing.
FLAMMABLE MATERIAL WARNING
Keep fixture at least 1.5 ft (1.5m) away from any
flammable materials, decorations, pyrotechnics, etc.
19
PLATINUM BEAM 5R EXTREME™ User Manual 1.0
www.elationlighting.com
MOUNTING POINTS
•
Overhead mounting requires extensive experience, including amongst others
calculating working load limits, installation material being used, and periodic
safety inspection of all installation material and the device. If you lack these
qualifications, do not attempt the installation yourself. Improper installation can
result in bodily injury.
•
Fixture is fully operational in the specific mounting positions as illustrated below.
SAFETY
CABLE
Always use a Safety Cable whenever installing this fixture in a suspended
environment to ensure the fixture will not drop if the clamp fails.
20
PLATINUM BEAM 5R EXTREME™ User Manual 1.0
www.elationlighting.com
CLAMP MOUNTING
The PLATINUM BEAM 5R EXTREME™ provides a unique mounting bracket assembly
that integrates the bottom of the base, the included Omega Brackets (x2) and
safety cable rigging point in one unit (see the illustration below). When mounting this
fixture to truss be sure to secure an appropriately rated clamps to the included
omega brackets using a M10 screw fitted through the center hole of the Omega
Bracket. Be sure to attach the included Safety Cable to the fixture using the safety
cable rigging point integrated in the base assembly.
SECURING
Regardless of the rigging option you choose for your PLATINUM BEAM 5R EXTREME™
always be sure to secure your fixture with a safety cable. The fixture provides a
built-in rigging point for a safety cable on the hanging bracket as illustrated above.
Be sure to only use the designated rigging point for the safety cable and never
secure a safety cable to a carrying handle.
21
PLATINUM BEAM 5R EXTREME™ User Manual 1.0
www.elationlighting.com
UNDERSTANDING DMX
DMX-512
DMX is short for Digital Multiplex. This is a universal protocol used by most lighting and
controller manufactures as a form of communication between intelligent fixtures
and controllers. DMX allows all makes and models of different manufactures to be
linked together and operate from a single controller. This is possible as long as all the
fixtures and the controller are DMX compliant. A DMX controller sends the DMX data
instructions to the fixture allowing the user to control the different aspects of an
intelligent light. DMX data is sent out as serial data that travels from fixture to fixture
via data “IN” and data “OUT” XLR terminals located on the fixtures (most controllers
will only have output jacks).
DMX LINKING
To ensure proper DMX data transmission, always use proper DMX cables and a
terminator. When using several DMX fixtures try to use the shortest cable path
possible. Never split a DMX line with a “Y” style connector. The order in which the
fixtures are connected in a DMX line does not influence the DMX addressing. For
example; a fixture assigned a starting DMX address of 1 may be placed anywhere in
the DMX chain, at the beginning, at the end, or anywhere in the middle. The DMX
controller knows to send data assigned to address 1 to that fixture no matter where
it is located in the DMX chain. The PLATINUM BEAM 5R EXTREME™ can be controlled
via DMX-512 protocol and the DMX address is set via the control menu.
DATA CABLE (DMX Cable) REQUIREMENTS (For DMX and Master/Slave Operation)
Your fixture and your DMX controller require a standard 3pin or 5pin XLR connector
for data input and data output (see figure below). If you are making your own
cables, be sure to use two conductor, shielded digital DMX cable rated at 120 ohms;
this cable is designed for DMX transmission and may be purchased from your Elation
dealer or at most professional lighting retailers. Your cables should be made with a
male and female XLR connector on either end of the cable. Also, remember that a
DMX line must be daisy chained and cannot be split, unless using an approved DMX
splitter such as Elation’s Opto Branch 4™, Opto Branch 8™, or DMX-Branch/4™.
22
PLATINUM BEAM 5R EXTREME™ User Manual 1.0
www.elationlighting.com
Be sure to follow the above figure when making your own cables. Do
not use the ground lug on the XLR connector. Do not connect the
cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
DMX-512 CONTROLLER CONNECTION
Connect the provided XLR cable to the female XLR output of your controller and the
other side to the male XLR input of the PLATINUM BEAM 5R EXTREME™ The diagram
below illustrates a typical DMX-512 connection when the fixture is in the 18 Channel
Extended Mode. You can chain multiple panels together through serial linking. The
cable that should be used is two conductor, shielded DMX cable with XLR input and
output connectors. Always be sure daisy chain your in and out data connections,
never split or “Y” your DMX connections unless you are using an approved DMX
splitter such as Elation’s Opto Branch 4™, Opto Branch 8™, or DMX-Branch/4™.
Address 37
Address 19
23
Address 1
PLATINUM BEAM 5R EXTREME™ User Manual 1.0
www.elationlighting.com
DMX-512 CONNECTION WITH DMX TERMINATOR
A DMX terminator should be used in all DMX lines especially in longer runs. The use of
a terminator may avoid erratic behavior in your DMX line. A terminator is a 120 ohm
1/4 watt resistor that is connected between pins 2 and 3 of a male XLR connector
(DATA + and DATA -). This fixture is inserted in the female XLR connector of the last
fixture in your daisy chain to terminate the line. Using a line terminator will decrease
the possibilities of erratic behavior.
5pin XLR DMX CONNECTORS
Some manufactures use 5pin XLR connectors for DATA transmission in place of 3pin.
5pin XLR fixtures may be implemented in a 3pin XLR DMX line. When inserting
standard 5pin XLR connectors in to a 3pin line a cable adaptor must be used, these
adaptors are readily available at most electric stores. The following chart details a
proper cable conversion.
24
PLATINUM BEAM 5R EXTREME™ User Manual 1.0
www.elationlighting.com
DMX ADDRESSING
All fixtures should be given a DMX starting address when using a DMX controller, so
the correct fixture responds to the correct control signal. This digital starting address
is the channel number from which the fixture starts to “listen” to the digital control
information sent out from the DMX controller. The allocation of this starting DMX
address is achieved by setting the correct DMX address on the digital display
located on the back of the fixture.
You can set the same starting address for all fixtures or a group of fixtures, or set
different address for each individual fixture. Be advised that setting all fixtures to the
same DMX address will subsequently control all fixtures in the same fashion, in other
words, changing the settings of one channel will affect all the fixtures simultaneously.
If you set each fixture to a different DMX address, each unit will start to “listen” to the
channel number you have set, based on the quantity of control channels (DMX
channels) of each fixture. That means changing the settings of one channel will only
affect the selected fixture.
In the case of the PLATINUM BEAM 5R EXTREME™, when in the 18 Channel Extended
Mode you should set the starting DMX address of the first unit to 1, the second unit to
19 (18 + 1), the third unit to 37 (19 + 18), and so on.
Note: During start-up the PLATINUM BEAM 5R EXTREME™ will automatically detect
whether a DMX data signal is being received or not. If DMX data signal is being
received, the display will show "Addr=XXX" (XXX representing the actual DMX
address). If the fixture is not receiving a DMX signal the display will flash. If your fixture
is connected to a DMX controller and the display is flashing (not receiving a DMX
signal), please check the following:
-
The 3pin or 5pin XLR input plug (cable with DMX signal from controller) is not
connected or is not inserted completely into the DMX input jack of the fixture.
-
The DMX controller is switched off or defective.
-
The DMX cable or connector is defective.
-
A DMX terminator has been inserted into the last fixture in your DMX chain.
25
PLATINUM BEAM 5R EXTREME™ User Manual 1.0
www.elationlighting.com
FIXTURE MENU
ON-BOARD SYSTEM MENU
The PLATINUM BEAM 5R EXTREME™ comes with an easy to navigate system menu.
The next section will detail the functions of each command in the system menu.
LCD MENU CONTROL PANEL
The control panel (see image below) located on back of the fixture allows you to
access the main menu and make all necessary adjustments to the PLATINUM BEAM
5R EXTREME™. During normal operation, pressing MODE/ESC button once will access
the fixture’s main menu. Once in the main menu you can navigate through the
different functions and access the sub-menus with the UP, DOWN, RIGHT, and LEFT
buttons. Once you reach a field that requires adjusting, press the ENTER button to
activate that field and use the UP and DOWN buttons to adjust the field. Pressing the
ENTER button once more will confirm your setting. You may exit the main menu at
any time without making any adjustments by pressing the MODE/ESC button.
NOTE: To access the LCD Menu Control Display via the internal battery, press and
hold the DC SWITCH button for 2 seconds. The LCD Menu Control Display will shut
OFF automatically about 1 minute from the last button press. To shut OFF the LCD
Menu Control Display immediately, set "Reset Default" menu option to “ON” in the
“Personality” menu and press the ENTER button to confirm your selection.
26
PLATINUM BEAM 5R EXTREME™ User Manual 1.0
www.elationlighting.com
27
PLATINUM BEAM 5R EXTREME™ User Manual 1.0
www.elationlighting.com
FUNCTION - Set DMX Address
Define desired DMX address via the Control Panel.
FUNCTION - DMX Value
Display DMX 512 value of each channel.
FUNCTION - Set To Slave
Define fixture slave mode (Slave1, Slave2, Slave3).
FUNCTION - Auto Program
Define fixture mode (Master or Alone) for running Auto Programs. Select desired
internal programs under “Select Program”, set the number of steps under “Edit
Program”, and edit individual scenes under “Edit Scenes”.
FUNCTION – Sound Control
Define fixture mode (Master or Alone) for running Auto Programs via sound
activation, default is Master.
INFORMATION - Time Information - Current Time
Displays fixture run time from last power ON.
The counter is reset after each time the fixture is powered OFF.
INFORMATION - Time Information - Total Run Hours
Displays fixture total run time.
28
PLATINUM BEAM 5R EXTREME™ User Manual 1.0
www.elationlighting.com
INFORMATION - Time Information - Last Run Hours
Displays fixture run time for a given period of time (i.e. rental period).
This counter can be reset.
INFORMATION - Time Information - Lamp Hours
Displays lamp total run time.
This counter should be reset at each lamp change.
INFORMATION - Time Information - Lamp Off Time
Displays lamp run time from the last power ON.
This counter is automatically reset after each time the lamp is powered ON.
INFORMATION - Time Information - LastRun Password
Display the fixture timer password. (038)
INFORMATION - Time Information - Clear Last Run
Resets the last run time of the fixture.
INFORMATION - Time Information - LampTime Password
Displays the lamp timer password. (038)
INFORMATION - Time Information - Clear Lamp Time
Resets the run time of the lamp.
INFORMATION - Temperature Information - Head Temperature
Displays temperature of the fixture.
INFORMATION - Software Version
Displays software version of the fixture.
LAMP CONTROL - Lamp ON or OFF
When ON, manual control of lamp power can be accessed via system menu.
LAMP CONTROL - Automatic Lamp ON/OFF
When ON, lamp is automatically powered ON when power is applied to fixture.
LAMP CONTROL - Lamp ON via DMX
When ON, lamp can be powered ON via a DMX controller.
LAMP CONTROL - Lamp OFF via DMX
When ON, lamp can be powered OFF via a DMX controller.
29
PLATINUM BEAM 5R EXTREME™ User Manual 1.0
www.elationlighting.com
LAMP CONTROL - Lamp ON at Temp
The fixture is designed to shut the lamp OFF when an excessive temperature is
sensed inside the head by the on-board CPU. The lamp is shut OFF to prevent
damage to the lamp and avoid possible internal damage to the fixture head.
This function sets the MIN internal operating temperature of the fixture head before
the lamp will restrike after the lamp has been automatically shut OFF.
LAMP CONTROL - Lamp OFF at Temp
The fixture is designed to shut the lamp OFF when an excessive temperature is
sensed inside the head by the on-board CPU. The lamp is shut OFF to prevent
damage to the lamp and avoid possible internal damage to the fixture head.
This function sets the MAX internal operating temperature of the fixture head when
the lamp will automatically be shut OFF.
PERSONALITY - Status Settings - Address Via DMX
Define desired DMX address via an external controller.
PERSONALITY - Status Settings - No DMX Status
Define how fixture operates if NO DMX signal is detected.
PERSONALITY - Status Settings - Pan Reverse
When ON, all PAN movements are reversed (inverted).
PERSONALITY - Status Settings - Tilt Reverse
When ON, all TILT movements are reversed (inverted).
PERSONALITY - Status Settings – Pan Degree
Select desired maximum degree of the Pan movement.
PERSONALITY - Status Settings - Feedback
When ON, the fixture automatically performs PAN / TILT correction in the event either
one is disrupted during normal operation.
PERSONALITY - Status Settings – Movement Speed
Select desired Movement Speed.
PERSONALITY - Status Settings – Mic Sensitivity
Select desired Microphone Sensitivity.
30
PLATINUM BEAM 5R EXTREME™ User Manual 1.0
www.elationlighting.com
PERSONALITY - Status Settings – Hibernation
Select desired Hibernation time.
PERSONALITY – Fans Control
Select desired Fan setting.
PERSONALITY - Display Setting – Shutoff Time
Define how many minutes before the LCD Menu display will automatically shut OFF.
PERSONALITY - Display Setting – Display Reverse
When ON, the LCD Menu display by is rotated (inverted) 180°.
PERSONALITY - Display Setting – Key Lock
When ON, Control Panel buttons lock automatically after exiting main menu for 15
seconds. To unlock, keep MODE/ESC button pressed for 3 seconds.
PERSONALITY – Temperature C/F
Define how fixture displays internal temperature (Celsius or Fahrenheit).
PERSONALITY – Initial Effect
Create custom PAN/TILT and Effect settings and save as a custom Home Position.
PERSONALITY – Wireless DMX
Control the functionality of the internal wireless DMX receiver.
PERSONALITY – Reset Default
When ON, all factory settings are restored.
RESET FUNCTION - Reset ALL
Reset ALL internal motors to Home Position.
RESET FUNCTION - Reset PAN and TILT
Reset only PAN and TILT motors to Home Position.
RESET FUNCTION - Reset Colors
Reset only Color Wheel to Home Position.
RESET FUNCTION - Reset Gobos
Reset only Gobo Wheels to Home Position.
RESET FUNCTION - Reset Shutter
Reset only blackout Shutter to Home Position.
31
PLATINUM BEAM 5R EXTREME™ User Manual 1.0
www.elationlighting.com
RESET FUNCTION - Reset Others
Reset ALL other motors not associated previously listed commands to Home Position.
EFFECT ADJUST – Test Channel
Select and auto test each individual channel function independently from the DMX
control board.
EFFECT ADJUST – Manual Control
Select and manually test and fine adjust each individual channel function
Independently from DMX control board. This function will center PAN and TILT motors
and set dimmer to 100%. PAN and TILT functions will still operate if the fixture needs to
be positioned to a flat clear surface. With the individual functions, you can focus the
light on a flat surface (wall) and perform fine adjustments.
EFFECT ADJUST – Calibration
ONLY QUALIFIED TECHNICIANS SHOULD PERFORM THIS FUNCTION.
This function allows small adjustments to be made to the effect wheels (Color, Gobo,
Shutter, etc.) to compensate for ware or in the event a sensor has been knocked
slightly out of place. Because improper use of this function can result in undesired
operation this function has been password protected. The password is 050 and must
be entered each time the calibration menu function is entered. Because calibration
is an extremely delicate procedure, instructions on performing this action are left out
of this manual. For a first time calibrator, please contact our customer support team
for step-by-step instructions.
USER MODE SET – User Mode
Select operating mode, which includes DMX Channel and User defined modes.
USER MODE SET – Edit User Mode
Create user defined channel orders allowing the fixture to match the channel order
of other fixtures on the market for easier operation. A total of three user modes may
be configured: User Mode A, User Mode B, and User Mode C.
EDIT PROGRAM – Select Program
Select one of the (10) user defined internal Auto Programs.
EDIT PROGRAM – Edit Program
Edit any of the (10) user defined internal Auto Programs.
32
PLATINUM BEAM 5R EXTREME™ User Manual 1.0
www.elationlighting.com
EDIT PROGRAM – Edit Scenes
Edit any of the scenes of the internal Auto Programs.
EDIT PROGRAM – Record Controller
The fixture features an integrated DMX-recorder by which you can transmit the
programmed scenes from your DMX-controller to the moving head. Adjust the
desired scene numbers via the encoder (from – to). When you call up the scenes at
your controller, they will automatically be transmitted to the moving head.
EDIT PROGRAM – Record Controller – Working With Built In Programs
A Master unit can send up to 3 different data groups to the Slave units, i.e. a Master
unit can start 3 different Slave units, which run 3 different programs. The Master unit
sends the 3 program parts in a continuous loop.
The Slave unit receives data from the Master unit according to the group which the
Slave unit was assigned to. If e.g. a Slave unit is set to “Slave 1” in the menu “Set to
Slave”, the Master unit sends “Auto Program Part 1” to the Slave unit.
If set to “Slave 2”, the Slave unit receives “Auto Program Part 2”.
To start an Auto Program proceed as follows:
1. Slave Setting
• Select “Function Mode”.
• Press ENTER to confirm.
• Select “Set to Slave”.
• Press ENTER to confirm.
• Select “Slave 1”, “Slave 2” or “Slave 3”.
• Press ENTER to confirm.
• Press MODE/ESC in order to return to the main menu.
33
PLATINUM BEAM 5R EXTREME™ User Manual 1.0
www.elationlighting.com
EDIT PROGRAM – Record Controller – Working With Built-In Program [continued]
2. Automatic Program Run
• Select “Function Mode”.
• Press ENTER to confirm.
• Select “Auto Program”.
• Press ENTER to confirm.
• Select “Master” or “Alone”.
• Press ENTER to confirm.
• Press MODE/ESC in order to return to the main menu.
3. Program Selection for Auto Pro Part
• Select “Edit Program”.
• Press ENTER to confirm.
• Select “Select Programs”.
• Press ENTER to confirm.
• Select “Auto Pro Part 1”, “Auto Pro Part 2” or “Auto Pro Part 3”, and select which
Slave program is to be sent. Selection “Part 1” means, that the Slave unit runs the
same program as the master units.
• Press ENTER to confirm.
• Press MODE/ESC in order to return to the main menu.
4. Program Selection for Edit Program
• Select “Edit Program”.
• Press ENTER to confirm.
• Select “Edit Program”.
• Press ENTER to confirm.
• Select the desired program. With this function you can edit specific scenes into a
specific program.
• Press ENTER to confirm.
• Press MODE/ESC in order to return to the main menu.
34
PLATINUM BEAM 5R EXTREME™ User Manual 1.0
www.elationlighting.com
EDIT PROGRAM – Record Controller – Working With Built-In Program [continued]
5. Automatic Scene Recording
• Select “Edit Program”.
• Press ENTER to confirm.
• Select “Edit Scenes”.
• Select desired scene numbers. A maximum of 250 scenes can be programmed.
• Press ENTER to confirm.
• Press MODE/ESC in order to return to the main menu.
Example:
Program 2 includes scenes: 10, 11, 12, & 13
Program 4 includes scenes: 8, 9, & 10
Program 6 includes scenes: 12, 13, 14, & 15
Auto Pro Part 1 is Program 2
Auto Pro Part 2 is Program 3
Auto Pro Part 3 is Program 6
The 3 Slave groups run the Auto Program in certain time segments, as shown in the
following picture:
35
PLATINUM BEAM 5R EXTREME™ User Manual 1.0
www.elationlighting.com
INTERNAL WIRELESS DMX RECIEVER (EWDMX)
The PLATINUM BEAM 5R EXTREME™ is equipped with an internal Elation Wireless DMX
Receiver, which is fully compatible with an Elation Wireless DMX System.
WORKING WITH THE INTERNAL WIRELESS DMX (EWDMX) System
Access the “Wireless DMX” sub menu from the “PERSONALITY” menu. The “Wireless
DMX” sub menu allows you to “Activate” (turn ON) the system, “Deactivate” (turn
OFF) the system, or “Reset” (CLEAR) the EWDMX system.
When the EWDMX system is “Activated” the internal DMX “IN” XLR jacks are turned
OFF. However the internal DMX “OUT” XLR jacks will function normally.
If the fixture is powered ON with the internal EWDMX system “Activated”, it will
automatically scan for a wireless DMX signal from an Elation Wireless Transmitter. If
NO wireless signal is received, it will electronically switch to the wired DMX mode.
WARNING!
NEVER connect a fixture to a controller via a DMX cable when the EWDMX
system is in use. This could cause serious damage to the controller!!
SETTING UP THE EWDMX SYSTEM
Follow the instructions included with the Elation EWDMX Transmitter and connect it to the
output of your DMX controller.
To sync your fixture with the Elation EWDMX Transmitter follow the steps below
•
Initially, the EWDMX indicator on the fixture should be solid RED.
•
Press and hold the configuration button on your EWDMX Transmitter for about 3
seconds. The RED/GREEN LED indicators on the EWDMX Transmitter and the fixture
should then begin to flash rapidly for about 5~ 10 seconds while the two systems pair.
•
Once the fixture is paired with the EWDMX Transmitter (T1), the EWDMX status
indicators on the both the fixture and the EWDMX Transmitter will stop flashing and
glow solid GREEN. If paring is unsuccessful repeat the process until paring is secured.
•
The fixture will store the pairing information inside a nondestructive memory bank once a
link is created between the fixture and an EWDMX Transmitter. The fixture will
remember the paired EWDMX Transmitter even if the fixture is turned OFF for extended
periods of time.
36
PLATINUM BEAM 5R EXTREME™ User Manual 1.0
www.elationlighting.com
CLEARING EWDMX TRANSMITTER LINK
•
Access the fixture’s main menu and toggle to the “PERSONALITY” menu, then access
the “Wireless DMX” sub menu and select “Clean WDMX Memo” to clear any existing
link between the fixture and a EWDMX Transmitter. The EWDMX indictor on the fixture
will turn solid RED when the link is severed.
•
You may also clear the link directly from the EWDMX Transmitter. First, be sure the
fixture(s) is powered ON, and then hold down the configuration button on the WDMX
Transmitter for as least 5 seconds. This will automatically clear the link between the
EWDMX Transmitter and any fixture that is powered ON. All EWDMX indictors will glow
solid RED if the procedure was successful.
EWDMX INDICATORS
RED/GREEN (Rapid Flashing) = Syncing to a EWDMX Transmitter
RED/GREEN (Slow Flashing) = Paired with a EWDMX Transmitter but not receiving a
DMX signal from a controller.
GREEN (Solid) = Paired with a EWDMX Transmitter and receiving DMX data
RED (Solid) = Not paired with a EWDMX Transmitter (FREE)
37
PLATINUM BEAM 5R EXTREME™ User Manual 1.0
www.elationlighting.com
DMX CHANNEL FUNCTIONS AND VALUES
38
PLATINUM BEAM 5R EXTREME™ User Manual 1.0
www.elationlighting.com
39
PLATINUM BEAM 5R EXTREME™ User Manual 1.0
www.elationlighting.com
40
PLATINUM BEAM 5R EXTREME™ User Manual 1.0
www.elationlighting.com
ERROR CODES
When power is applied, the unit will automatically enter a “Reset/Test” mode. This
mode brings all the internal motors to a home position. If there is an internal problem
with one or more of the motors an error code will flash in the display in the form of
“XXer” were as XX will represent a function number. For example, when the display
shows “0Er” it means there is some type of error with the Pan motor. If there are
multiple errors during the start-up process they will all flash in the display. For
example: if the fixtures has errors on Channel 1, 2, and 5 all at the same time, you will
see the error message “01Er”, “02Er”, and ”05Er” flash repeated 5 times.
If an error does occur during the initial start-up procedure the fixture will
self-generate a second reset signal and try to realign all the motors and correct the
errors. If the error persists after a second attempt a third attempt will be made. If
after a third attempt all the errors have not been corrected the fixture will make the
following determinations:
•
3 or More Errors - The fixture cannot function properly with three or more errors
therefore the fixture will place itself in a stand-by mode until subsequent repairs
can be made.
•
Less Than 3 Errors - The fixture has less than 3 errors; therefore most other functions
will work properly. The fixture will attempt to operate normally until the errors can
be correct by a technician. The errors in question will remain flashing in the
display as a reminder of internal errors.
PAN Movement Er
The yoke is not located in the default position after start-up or after a reset
command.
This message will appear after a fixture reset if the pan’s
magnetic-indexing circuit malfunctions (sensor failed or magnet is missing) or there is
a motor failure (defective motor or a defective motor IC drive on the main PCB). This
error may also be displayed if the head/yoke was blocked during a reset function.
TILT Movement Er
This message will appear after a fixture reset if the tilt’s magnetic-indexing circuit
malfunctions (sensor failed or magnet is missing) or there is a motor failure (defective
motor or defective motor IC drive on main PCB). This error may also be displayed if
the head was blocked during a reset function.
41
PLATINUM BEAM 5R EXTREME™ User Manual 1.0
www.elationlighting.com
Color Wheel Er
The color wheel is not located in the default position after start-up or after a reset
command. This message will appear after a fixture reset if the color wheel’s
magnetic-indexing circuit malfunctions (sensor failed or magnet is missing) or there is
a stepper motor failure (defective motor or defective motor IC drive on main PCB).
Gobo Wheel 1 Er
The gobo-wheel is not located in the default position after start-up or after a reset
command. This message will appear after a fixture reset if the gobo wheel’s
magnetic-indexing circuit malfunctions (sensor failed or magnet is missing) or there is
a stepper motor failure (defective motor or defective motor IC drive on main PCB).
Gobo Rot 1 Er
The gobo is not located in the default position after start-up or after a reset
command. This message will appear after a fixture reset if the gobo positioning
magnetic-indexing circuit malfunctions (sensor failed or magnet is missing) or there is
a stepper motor failure (defective motor or defective motor IC drive on main PCB).
Focus Er
This message will appear after the reset of the fixture and if the magnetic indexing
circuit malfunctions (sensor failed or magnet missing) or the stepping-motor is
defective (or its driver circuit on the main PCB). The focus motor is not located in the
default position after the reset.
Prism Rot Er
This message will appear after the reset of the fixture and if the magnetic indexing
circuit malfunctions (sensor failed or magnet missing) or the stepping-motor is
defective (or its driver circuit on the main PCB). The prism wheel is not located in the
default position after the reset.
42
PLATINUM BEAM 5R EXTREME™ User Manual 1.0
www.elationlighting.com
CLEANING AND MAINTENANCE
CLEANING
Frequent cleaning is recommended to insure proper function, optimized light output,
and an extended life. The frequency of cleaning depends on the environment in
which the fixture operates: damp, smoky or particularly dirty environments can
cause greater accumulation of dirt on the fixture’s optics.
•
Clean the external lens surface at least every 20 days with a soft cloth to avoid
dirt/debris accumulation.
•
Never use alcohol, solvents, or ammonia based cleaners.
MAINTENANCE
Regular inspections are recommended to insure proper function and extended life.
There are no user serviceable parts inside this fixture, please refer all other service
issues to an authorized Elation service technician. Should you need any spare parts,
please order genuine parts from your local Elation dealer.
Please refer to the following points during routine inspections:
•
A detailed electric check by an approved electrical engineer every three
months, to make sure the circuit contacts are in good condition and prevent
overheating.
•
Be sure all screws and fasteners are securely tightened at all times. Lose screws
may fall out during normal operation resulting in damage or injury as larger parts
could fall.
•
Check for any deformations on the housing, color lenses, rigging hardware and
rigging points (ceiling, suspension, trussing). Deformations in the housing could
allow for dust to enter into the fixture. Damaged rigging points or unsecured
rigging could cause the fixture to fall and seriously injure a person(s).
•
Electric power supply cables must not show any damage, material fatigue or
sediments. Never remove the ground prong from the power cable.
43
PLATINUM BEAM 5R EXTREME™ User Manual 1.0
www.elationlighting.com
TECHNICAL SPECIFICATIONS
FEATURES
3° Sharp Pin Spot Beam
CTO and CTB Color Correction
8 Facet Rotating Prism and Frost Effects
Super Fast 16 bit 3-Phase Pan and Tilt Motors
Flicker Free Operation for TV and FILM
Internal EWDMX Wireless DMX Receiver
Remote Device Management Protocol Support
SOURCE
189W Platinum 5R Lamp
2,000 Hour Average Life
PHOTOMETRIC DATA
100,100 LUX 9,299 FC @49.2’ (15M)
EFFECTS
Frost
Motorized Focus
Strobe (1-18 fps)
Electronic Dimming: 0% - 100%
8 Facet Rotating Prisms and Macros
COLOR
(12) Colors Including UV, CTO, CTB + White
GOBOS
(8) Metal Rotating, Indexing, Interchangeable Gobos
CONTROL / CONNECTIONS
(3) DMX Channel Modes (12/14/18)
Remote Device Management
Pan Movement: 540°/630° / Tilt Movement: 270°
6 Button Control Panel
Full Color 180° Reversible LCD Menu Display
16 Bit 3-Phase Pan/Tilt Motors
3pin & 5pin DMX In/Out
powerCON In
Internal EWDMX Wireless DMX Receiver
SIZE / WEIGHT
Length: 13.9” (352mm)
Width: 13.0” (329mm)
Vertical Height: 20.0” (509mm)
Weight: 44.0 lbs. (20.0 kg)
ELECTRICAL / THERMAL
AC 100-240V - 50/60Hz
350W Max Power Consumption
14°F to 113°F (-10°C to 45°C)
APPROVALS / RATINGS
CE Approved, cETLus Approved, IP20 Rated
Please Note: Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice.
44
PLATINUM BEAM 5R EXTREME™ User Manual 1.0
www.elationlighting.com
COLORS + GOBOS
PHOTOMETRIC DATA
Please Note: Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice.
45
PLATINUM BEAM 5R EXTREME™ User Manual 1.0
www.elationlighting.com
DIMENSIONAL DRAWINGS
CIRCUIT SCHEMATICS
Please Note: Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice.
46
PLATINUM BEAM 5R EXTREME™ User Manual 1.0
www.elationlighting.com
OPTIONAL ACCESSORIES
ORDER CODE
ITEM
TRIGGER CLAMP
Heavy Duty Wrap Around Hook Style Clamp
DRCPLAT
Dual Flight Case For Platinum Beam 5R EXTREME™
DRCPLATQUAD
Quad Flight Case For Platinum Beam 5R EXTREME™
ELO211
Eloader II™ Software Updater Box
EWDMXSYSTEM
Wireless DMX System (1 Transmitter, 1 Receiver)
EWDMXT
Wireless DMX Transmitter
EWDMXR
Wireless DMX Receiver
AC3PDMX5PRO
5 ft. (1.5m) 3pin PRO DMX Cable
AC3PDMX10PRO
10 ft. (3m) 3pin PRO DMX Cable
AC5PDMX5PRO
5 ft. (1.5m) 5pin PRO DMX Cable
AC5PDMX10PRO
10 ft. (3m) 5pin PRO DMX Cable
Additional cable lengths available: 15, 25, 50, 100 ft (4.5, 7.5, 15.2, 30.5m)
47
PLATINUM BEAM 5R EXTREME™ User Manual 1.0
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising