RP-M251CE, RP-M301CE and RP
RP-series slicer
M251CE/M301CE/M351CE
Service Instructions
76102-908
ENGLISH
issue 2 18.07.00
2.1 — Safety
Contents
Table of Contents:
1
Introduction
2
Safety
3
Operation
4
Installation
5
Electrical Drawings
6
Technical Information
7
Appendices
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
i
2.1 — Safety
ii
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
Section 1
Introduction
Table of Contents:
page no
1.1
General
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
1-3
1-1
1 — Introduction
1-2
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
1 — Introduction
1.1
General
The Avery Berkel slicing machine and its accessories are manufactured in
accordance with the EEC 89/392 Machinery Directive and further modifications.
They meet all legislative requirements valid at the date of manufacture.
Its principle characteristics are easy cleaning, robust manufacture, safe and
reliable operation.
The materials utilised, anodised aluminium, stainless steel and plastics have
been selected with due regard to hygiene regulations, and ensure that the
machine has a long life.
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
1-3
1 — Introduction
1-4
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
Section 2
Safety
Table of Contents:
page no
2.1
2.2
Electrical safety devices
Mechanical safety devices
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
2-3
2-4
2-1
2 — Safety
2-2
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
2 — Safety
2.1
Electrical safety devices
The electrical safety devices in accordance
with the EN 60204 standards are:
• Start and stop pushbuttons.
• Control circuit provided with electric
servo-control; in the case of blade
clamping the machine must be restarted manually.
• Device to stop the rotation of the
blade if the clamping handle of the
blade guard is released.
Note:
When the machine is not used:
• Make sure that it is off.
• Re-position the slice thickness control
to zero.
Do not remove the labels placed on the
machine. Only replace them if damaged.
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
V 230
2-3
2 — Safety
2.2
Mechanical safety devices
The slicer is manufactured according to
EEC 89/392 Machinery Directive and
further modifications.
The mechanical safety devices are:
• Product holder removable only with
the slice thickness control on 0 (slice
thickness plate positioned to protect
the blade). After removing the
product holder the slice thickness
plate is mechanically clamped.
• Protection devices mounted on the
product holder to prevent the operator
from any accidental contact with the
blade.
• Blade guard. This fixed ring protects
that part of the blade which is not
used for the cutting operation.
• A special mechanical safety device
which permits sharpening of the
blade, keeping the fingers of the
operator away from the cutting edge
of the blade.
2-4
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
Section 3
Operation
Table of Contents:
page no
3.1
3.2
RP-M251CE/M301CE
3.1.1
Definitions
3.1.2
Technical specification
3.1.3
Slicer operation and use
3.1.4
Cleaning and operator removable parts
3.1.5
Sharpening
3.1.6
Lubrication
RP-M351CE
3.2.1
Definitions
3.2.2
Technical specification
3.2.3
Slicer functioning and use
3.2.4
Cleaning and operator removable parts
3.2.5
Sharpening
3.2.6
Lubrication
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
3-3
3-3
3-4
3-5
3-9
3-12
3-16
3-17
3-17
3-18
3-19
3-23
3-26
3-30
3-1
3 — Operation
3-2
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
3 — Operation
3.1
RP-M251CE/M301CE
3.1.1
Definitions
1.
Control pushbuttons
2.
Slice thickness control
3.
Carriage
4.
Product holder clamping
handle
5.
Product holder
6.
Product holder pushing
handle
7.
Last slice device
8.
Pusher
9.
Carriage bar oiler
10.
Blade
11.
Blade cover
12.
Blade guard
13.
Slice thickness plate
14.
Slice deflector
15.
Slice receiving tray
16.
Blade cover fastener
handle
17.
Blade sharpener cover
18.
Integrated blade
sharpener
11
12
8
7
10
13
6
4
1
2
3
5
17
15
18
16
14
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
9
3-3
3 — Operation
3.1.2
Technical specification
1.
Blade Ø mm
2.
Slicing capacity
3.
Dimensions mm
4.
Weight Kg
a. without packaging
b. with packaging
5.
Range temperature +5 C - +40 C
6.
Slice thickness control 0 - 14 mm
7.
Blade 300 rev/min
8.
Acoustic <70 dB
9.
Protection of the electrical system
and switches grade IP 55
10.
Cutting zone
RP-M251CE
RP-301CE
250
300
A
130
170
B
200
210
C
190
220
D
170
200
1.
2.
3.
4.
E
460
F
330
G
580
H
420
I
630
a.
24
b.
29
Motors: electrical data
130
3-4
270 230 50
1~
A
0,8 0,8 1450
CL
B
S1
Degree of
Protection
n
min
Service
Cos ϕ
Hz
Phase No.
V
Connection
Max.
Nominal
W
A
VL
F
IP
3
400
8
33
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
3 — Operation
3.1.3
Slicer operation and use
The following products can be sliced:
sausages, ham, cheese, bread. If large
quantities of bread or cheese are usually
cut, a teflon coating is recommended.
(Optional accessory 97).
Note:
The following must not be sliced:
• non-edible products.
• foodstuffs with bones.
• frozen products.
How to load the product to be cut
1.
Check that the slicer is switched off
and set the slice thickness control to
zero.
2.
Pull the product holder towards the
operator.
3.
Lift and rotate the last slice device
outwards
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
3-5
3 — Operation
3-6
4.
Place the product to be cut against
the wall of the product holder and the
slice thickness plate.
5.
Place the last slice device on the
product to be cut in a position away
from the slice thickness plate. The
product is fed by gravity to the slice
thickness plate making cutting easier.
6.
Set the slice thickness control to the
thickness desired.
7.
Press switch
machine.
8.
Push the product holder at a steady
speed towards the blade end then
pull it back towards the operator, and
repeat the operation.
9.
After cutting the product, leave the
product holder in position back
towards the operator end.
10.
to stop; re-set
Press pushbutton
the slice thickness control to zero,
and remove the product.
to switch on the
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
3 — Operation
How to load short goods for
cutting (last slice)
WARNING:
DO NOT USE YOUR HANDS TO
PUSH THE GOODS TOWARDS THE
BLADE.
FOLLOW THESE INSTRUCTIONS
WITH GREAT CARE.
1.
Check that the slice thickness control
is set on zero and the slicer is
switched off.
2.
Pull the product holder towards the
operator.
3.
Lift and rotate the last slice device
outwards.
4.
Place the product to be cut against
the wall of the product holder and the
slice thickness plate.
5.
Push the goods against the slice
thickness plate using the last slice
device.
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
3-7
3 — Operation
6.
Set the slice thickness control to the
required thickness.
7.
Press pushbutton
machine.
8.
Hold the handle of the last slice
device. Apply a light pressure on the
goods towards the slice thickness
plate and push the product holder to
the end of the blade stroke; then pull
it back to the operator and repeat the
operation.
9.
After cutting the product, move the
product holder back towards the
operator.
10.
to stop. Reset
Press pushbutton
the slice thickness control to zero,
and remove the product.
to start the
Sharpening
If the product is not cut frequently, the blade
must be sharpened following the
instructions indicated in 3.1.5.
3-8
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
3 — Operation
3.1.4
Cleaning
The machine must be cleaned once a day or
more frequently if necessary.
Clean all the parts using a cloth moistened
with water and washing up liquid, and a
brush (do not use strong detergents).
WARNING:
DO NOT USE A WATER JET.
DANGER:
PERFORM THE CLEANING
OPERATIONS WITH GREAT CARE:
DANGER OF INJURY.
Component removal
Product holder
1.
Rotate the product holder clamping
handle counterclockwise.
2.
Set the slice thickness control to zero.
3.
Pull the carriage to the operator end of
its travel. A click will inform the
operator that the product holder is
clamped.
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
3-9
3 — Operation
4.
Remove the last slice device from the
guide bar.
5.
Lift the product holder from the
carriage. The slice thickness control
remains clamped on zero.
Note:
The slicer thickness control is clamped on
zero.
Slice deflector
1.
Loosen the fixing screw and remove
the slice deflector.
Blade cover
1.
Loosen the blade cover fastening
handle by rotating it counterclockwise.
2.
Lift the blade cover from the blade by
pushing on the handle in the direction
indicated by the arrow.
Note:
Once removed from the blade cover, an
interlocking device stops the rotation of the
blade.
3 - 10
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
3 — Operation
Blade cleaning
1.
Lift the blade cover.
DANGER:
TAKE CARE TO AVOID ANY
ACCIDENTAL CONTACT WITH
THE BLADE WHILE CLEANING IT.
2.
Press a damp cloth on the front side
of the blade and move slowly from
the centre towards the edge in the
direction of the arrow.
3.
Follow these instructions to clean the
other side of the blade.
4.
Dry both sides of the blade with a
cloth in the same way.
5.
Insert a damp cloth between the
blade and the protection ring. Pull it
outwards and move it to and fro to
clean the inside of the protection ring.
6.
After cleaning re-place the blade
cover; insert the fastener and screw it
clockwise to clamp the blade cover.
Lower the sharpener protective cover.
IMPORTANT:
Leave all the parts to soak in warm water
and washing-up liquid (do not use strong
detergents) and clean them by using a
brush or a cloth. Rinse them in warm water
and dry them.
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
3 - 11
3 — Operation
To assemble the machine follow the
reverse of the procedure for disassembly.
3.1.5
Blade sharpening
If the cut is unsatisfactory, the blade must
be sharpened. The intervals between the
sharpening operations depend on the use
of the slicer and the kind of products
being cut.
This operation must be carried out by
qualified personnel.
The blade must be replaced when its
diameter is 10 mm less than that of a new
one.
WARNING:
THE REPLACEMENT OF THE
BLADE IS A DANGEROUS
OPERATION.
IF THE SHARPENING QUALITY IS
NOT SATISFACTORY, REPLACE
THE STONES.
CONTACT CUSTOMER SERVICE
AT AVERY-BERKEL.
WARNING:
SLICERS FITTED WITH A
TOOTHED KNIFE (OPTION) ARE
ONLY SUITABLE FOR CUTTING
BREAD. THE KNIFE
SHARPENING MUST BE DONE
ONLY BY A TECHNICAL
ASSISTANCE CENTRE.
3 - 12
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
3 — Operation
The sharpening operation
Wear protective gloves
Follow the instructions below for correct
blade sharpening:
1.
Clean the blade and remove any
greasy residue.
2.
Make sure that the machine is
switched off.
3.
Set the slice thickness control at zero
to make sure that the blade is
covered by the slice thickness plate.
WARNING:
DURING THE FOLLOWING
OPERATIONS THE BLADE MUST
ALWAYS BE COVERED BY THE
REMOVABLE PROTECTION.
4.
Lift the sharpener cover.
5.
Pull the sharpener release lever and
rotate it towards the blade.
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
3 - 13
3 — Operation
6.
Release the lever; the blade
sharpener will be correctly located.
7.
Push pushbutton
machine.
to start the
Note:
The sharpening operation will take 10-15
seconds.
3 - 14
8.
Sharpening: rotate the handle to
bring the two grinding wheels on to the
blade. The blade will be sharpened
and burred simultaneously.
9.
After sharpening press the stop
pushbutton.
STOP
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
3 — Operation
10.
Pull the lever to restore the sharpener
to its initial position.
11.
Lower the sharpener cover.
Cleaning the grinding wheels
For satisfactory sharpening the grinding
wheel must always be clean.
Remove dirt and grease with alcohol and
the special brush supplied.
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
3 - 15
3 — Operation
3.1.6
Guides lubrication
This operation must be carried out after
cleaning the slicer or whenever the sliding
action is difficult.
Use Berkel slicer oil.
Lubrication of the guide bar for
the last slice device
1.
Drop some oil on the bar.
2.
Slide the last slice device along the
guide bar.
Lubrication of the guide bar for
the product holder carriage
1.
Push the product holder towards the
operator.
2.
Pour lubricating oil into the special
carriage bar lubricator.
3.
Push the product holder to and fro
and repeat the operation.
Leave it in a position at the end
nearest to the operator.
3 - 16
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
3 — Operation
3.2
RP-M351CE
3.2.1
Definitions
1.
Control pushbuttons
2.
Slice thickness control
3.
Carriage
4.
Product holder clamping
handle
5.
Product holder
6.
Product holder pushing
handle
7.
Last slice device
8.
Pusher
9.
Carriage bar oiler
10.
Blade
11.
Blade cover
12.
Blade guard
13.
Slice thickness plate
14.
Slice deflector
15.
Slice receiving tray
16.
Blade cover fastener
handle
17.
Blade sharpener cover
18.
Self-contained blade
sharpener
12
11
10
13
6
1
4
2
3
8
5
7
17
18
15
14
16
9
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
3 - 17
3 — Operation
3.2.2
Technical data
1.
Blade Ø mm
2.
Slicing capacity
3.
Dimensions mm
4.
Weight Kg
a. without packaging
b. with packaging
5.
Range temperature +5 C - +40 C
6.
Slice thickness control 0 - 14 mm
7.
Blade 200 rev/min
8.
Acoustic <70 dB
9.
Protection of the electrical system and switches grade IP 55
10.
Cutting zone
RP-M351CE
1.
2.
3.
4.
350
A
190
B
260
C
280
D
250
E
540
F
420
G
650
H
540
I
740
L
950
a.
39
b.
48
Motors: electrical data
3 - 18
330 230 50
1~
0,8
2
1450
CL
B
S1
Degree of
Protection
A
n
min
Service
Phase No.
Hz
Connection
V
Cos ϕ
160
Max.
Nominal
W
A
VL
F
IP
5
250
35
33
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
3 — Operation
3.2.3
Slicer operation and use
The following products can be sliced:
sausages, ham, cheese, bread. If large
quantities of bread or cheese are usually
cut a teflon coating is recommended
(Optional accessory 97).
Note:
The following cannot be sliced:
• non-edible products.
• foodstuffs with bones.
• frozen products.
How to load the product to be cut
1.
Check that the slicer is switched off
and set the slice thickness control to
zero.
2.
Push the product holder towards the
operator.
3.
Lift and rotate the last slice device.
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
3 - 19
3 — Operation
3 - 20
4.
Place the product to be cut against
the wall of the product holder and the
slice thickness plate.
5.
Place the last slice device on to the
product to be cut in a position away
from the slice thickness plate. The
product is fed to the slice thickness
plate by gravity to make the cut
easier.
6.
Set the slice thickness control to the
required thickness.
7.
Press switch
machine.
8.
Push the product holder at a steady
speed to the end of the blade, then
pull it back towards the operator and
repeat the operation.
9.
After cutting the product, pull the
product holder back towards the
operator.
10.
to stop; reset
Press pushbutton
the slice thickness control to zero,
and remove the product.
to switch on the
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
3 — Operation
How to load short goods for
cutting (last slice)
WARNING:
DO NOT USE YOUR HANDS TO
PUSH THE GOODS TOWARDS THE
BLADE. FOLLOW THESE
INSTRUCTIONS WITH GREAT
CARE.
1.
Check that the slice thickness control
is set on zero and the slicer is
switched off.
2.
Pull the product holder towards the
operator.
3.
Lift and rotate the last slice device
outwards.
4.
Place the product to be cut against
the wall of the product holder and the
slice thickness plate.
5.
Push the goods against the slice
thickness plate using the last slice
device.
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
3 - 21
3 — Operation
6.
Set the slice thickness control to the
required thickness.
7.
Press pushbutton
machine.
8.
Hold the handle of the last slice
device. Apply a light pressure on the
goods towards the slice thickness
plate and push the product holder to
the end of the blade; then pull it back
towards the operator and repeat the
operation.
9.
After cutting the product, pull the
product holder back towards the
operator.
10.
to stop; reset
Press pushbutton
the slice thickness control to zero and
remove the product.
to start the
Sharpening
If product is not cut frequently the blade
must be sharpened. Follow the instructions
indicated in 3.2.5.
3 - 22
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
3 — Operation
3.2.4
Cleaning
The machine must be cleaned once a day
or more frequently if necessary.
Clean all the parts using a cloth moistened
with water and washing up liquid, and a
brush (do not use strong detergents).
WARNING:
DO NOT USE A WATER JET.
DANGER:
CARRY OUT THE CLEANING
OPERATIONS WITH GREAT CARE:
DANGER OF INJURY
Component removal
Product holder
1.
Loosen the product holder by rotating
the product holder clamping handle
counterclockwise.
2.
Set the slice thickness control to zero.
3.
Pull the product holder towards the
operator until it clicks. The click will
inform the operator that the product
holder is clamped.
4.
Lift the last slice device from the guide
bar.
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
3 - 23
3 — Operation
5.
Lift the product holder from the
carriage.
Note:
The slice thickness control remains
clamped on zero.
Slice deflector
1.
Rotate the slice deflector and keep it
away from the blade.
Blade cover
1.
Loosen the blade cover fastening
handle by rotating it counterclockwise.
2.
Push on the handle in the direction
indicated by the arrow to lift the blade
cover from the blade.
Blade cleaning
1.
Lift the blade cover.
Note:
When the blade cover is removed an
interlocking device prevents blade rotation.
DANGER:
DURING BLADE CLEANING
OPERATIONS, TAKE CARE TO
AVOID ACCIDENTAL CONTACT
WITH IT.
3 - 24
2.
Press a damp cloth on the front side
of the blade and move slowly from the
center towards the edge in the
direction of the arrow.
3.
Follow these instructions to clean the
other side of the blade.
4.
Dry both sides of the blade with a
cloth in the same way.
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
3 — Operation
5.
Insert a damp cloth between the
blade and the protection ring. Pull it
outwards and move it to and fro to
clean the inside of the protection ring.
6.
After cleaning replace the blade
cover, insert the fastener and screw it
clockwise to clamp the blade cover.
7.
Lower the sharpener protective cover.
IMPORTANT:
Leave all the parts to soak in warm water
and washing-up liquid (do not use strong
detergents) and clean them by using a
brush or a cloth. Rinse them in warm water
and dry them.
To assemble the machine follow the reverse
of the disassembly procedure.
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
3 - 25
3 — Operation
3.2.5
Blade sharpening
If the cut is not satisfactory, the blade must
be sharpened. The intervals between the
sharpening operations depend on the use
of the slicer and the kind of products cut.
This operation must be carried out only by
qualified personnel.
The blade must be replaced when its
diameter is 10 mm less than that of a new
one.
WARNING:
CONTACT CUSTOMER SERVICES
AT AVERY BERKEL FOR BLADE
REPLACEMENT.
WARNING:
THE SLICERS FITTED WITH A
TOOTHED KNIFE (OPTION) ARE
SUITABLE ONLY FOR CUTTING
BREAD. KNIFE SHARPENING
MUST BE DONE AT A TECHNICAL
ASSISTANCE CENTRE.
WARNING:
IF THE SHARPNESS IS NOT
SATISFACTORY BOTH GRINDING
WHEELS IN THE BLADE
SHARPENER MUST BE
REPLACED. ONLY QUALIFIED
PERSONNEL SHOULD REPLACE
THEM.
3 - 26
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
3 — Operation
Sharpening operation
Wear protective gloves
For a correct blade sharpening, follow the
instructions below:
1.
Clean the blade and remove any
greasy residue, as in 3.2.4.
2.
Make sure that the machine is
switched off.
3.
Set the slice thickness control to zero
to ensure that the blade is shielded by
the slice thickness plate.
WARNING:
DURING THE FOLLOWING
OPERATIONS THE BLADE MUST
ALWAYS BE SHIELDED BY THE
REMOVABLE PROTECTION.
4.
Lift the sharpener cover.
5.
Pull the sharpener release handle.
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
3 - 27
3 — Operation
6.
Rotate the sharpener assembly to
stand over the blade.
7.
The blade sharpener is now correctly
fixed.
8.
Push pushbutton
machine.
to start the
Note:
The sharpening operation will take 10-15
seconds.
3 - 28
9.
Sharpening: rotate the lever and
bring the two grinding wheels on to
the blade. The blades are
simultaneously sharpened and
burred.
10.
After sharpening press the stop
pushbutton.
STOP
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
3 — Operation
11.
Pull the handle to return the sharpener
to its original position.
12.
Lower the sharpener cover.
Cleaning the grinding wheels
The grinding wheel and its pin can be
removed from the sharpener by taking it off
in the direction of the arrow.
For the sharpest blades the grinding wheel
must always be clean.
Remove dirt and grease with alcohol and the
special brush supplied.
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
3 - 29
3 — Operation
3.2.6
Guides lubrication
This operation must be performed after
cleaning the slicer or whenever the sliding
action is difficult.
Use Berkel slicer oil.
Lubrication of the guide bar for
the last slice device
1.
Drop some oil on the bar.
2.
Slide the last slice device along the
guide bar.
Lubrication of the guide bar for
the product holder carriage
1.
Pull the product holder towards the
operator.
2.
Pour lubricating oil into the special
carriage bar lubricator.
3.
Push the product holder to and fro
and repeat the operation.
Leave it at the operator end.
3 - 30
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
Section 4
Installation
Table of Contents:
page no
4.1
RP-M251CE/M301CE/M351CE
4.1.1
Positioning of slicer
4.1.2
Electrical supply
4.1.3
Preliminary cleaning
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
4-3
4-3
4-3
4-3
4-1
4 — Installation
4-2
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
4 — Installation
4.1
RP-M251CE/M301CE/M351CE
4.1.1
Installation
The slicer must be mounted horizontally on
a stable, robust and antiskid base capable
of supporting its weight (3.1.2 and 3.2.2).
The recommended height of the working
table is 800 mm.
Check that the product holder is not
clamped and the product to be cut can be
easily loaded (3.1.2 and 3.2.2).
4.1.2
Electrical supply
The machine must be installed near a
mains socket.
Check that the power supply voltage
corresponds to that on the information label
and that it is correctly connected to earth.
4.1.3
1.
Insert the plug into the mains socket.
2.
Check that the blade cover fastening
handle is screwed up tightly.
3.
Check that the blade sharpener is
lowered and that the protective cover
is closed.
4.
to switch on the
Press pushbutton
machine (the mains supply light will
illuminate).
Preliminary cleaning
Before connecting the plug clean off the
protective oil from the machine.
Follow the instructions indicated in 3.1.4
and 3.2.4.
Note:
The working table must always be cleaned.
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
4-3
4 — Installation
4-4
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
Section 5
Electrical Drawings
Table of Contents:
page no
5.1
5.2
5.3
5.4
5.5
Wiring diagram RP-M251CE/M301CE
Wiring diagram RP-M351CE
Circuit diagram RP-M251CE/M301CE
Circuit diagram RP-M351CE
Circuit diagram RP-M351CE (Three Phase)
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
5-3
5-4
5-5
5-6
5-7
5-1
5 — Operation
5-2
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
5 — Electrical Drawings
5.1
Wiring diagram RP-M251CE/M301CE
Blue
Grey
No.
Colour
1
Red
2
Green
3
Grey
4
Brown
5
Blue
6
Black
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
5-3
5 — Operation
5.2
Wiring diagram RP-M351CE
M1
Red
M2
Grey
T2
Blue
T2
Black
Gr
ey
5-4
No.
Colour
1
Red
2
Green
3
Grey
4
Brown
5
Blue
6
Black
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
5 — Electrical Drawings
Black
Grey
Green
Blue
Brown
Circuit diagram RP-M251CE/M301CE
Red
5.3
POS
DESCRIZIONE
POS
DESCRIZIONE
X1
SPINA
C3
CONDENSATORE 5 F VS25E-522-822-842
T1
TRASFORMATORE 0-230/0-24V 2,2VA
C3
CONDENSATORE 8 F GL25E-30E H-L-M25-30E
F1
FUSIBILE 160mA
R1/R2
RESISTENZA 2k2 1/4W
D1
RADDRIZZATORE 1A
R3
RESISTENZA 10k
D2
DIODO DI PROTEZIONE G001
R4
RESISTENZA 47 Hom
L1
LED LINEA ARANCIONE
K1/K2
RELE’ DI COMANDO 12Vcc OMRON
L2
LED MARCIA VERDE
K3/K4
RELE’ DI COMANDO
C1
CONDENSATORE ELETTROLITICO 220 F 50V
S1
PULSANTE STOP
C2
CONDENSATORE ELETTROLITICO 220 F 50V
No DISEGNO
S 2244
DATA
MACCHINA
27-05-99
RP-M251CE/RP-M301CE
TENSIONE: 230V-50Hz
S2
PULSANTE START
S3
PROTEZIONE DISCO COPRILAMA
RP-M254CE/RP-M304CE
Ci riserviarno la proprieta’a termini di legge di questo disegno con divieto di riprodurlo anche in parte o di renderlo noto a terzi.
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
5-5
5 — Operation
POS
DESCRIZIONE
POS
DESCRIZIONE
X1
SPINA
R1/R2
RESISTENZA 2,2k 1/2W
T1
TRASFORMATORE 0-230-400V/0-24V 5,5VA
R3
RESISTENZA 47 OHM 1/4W
F1
FUSIBILE 500mA
R4
RESISTENZA 10k 1/4W
Black
Grey
Green
Blue
Brown
Circuit diagram RP-M351CE
Red
5.4
D1
RADDRIZZATORE 1A
K1
RELE’ DI COMANDO 24Vcc OMRON
D2
DIODO
K2
MINICONTATTORE 24Vcc ABB
L1
LED LINEA VERDE
K3
RELE’ DI AVVIAMENTO
L2
LED MARCIA BIANCO
S1
PULSANTE STOP
C1
CONDENSATORE ELETTROLITICO 200 F 35V
S2
PULSANTE START
C2
CONDENSATORE ELETTROLITICO 200 F 35V
S3
CONTATTO DI PROTEZIONE DISCO COPRILAMA
C3
CONDENSATORE 35 F 250V
No DISEGNO
S 2235
DATA
MACCHINA
28-05-99
RP-M351CE
TENSIONE: 230V-50Hz
Ci riserviarno la proprieta’a termini di legge di questo disegno con divieto di riprodurlo anche in parte o di renderlo noto a terzi.
5-6
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
5 — Electrical Drawings
POS
DESCRIZIONE
POS
DESCRIZIONE
X1
SPINA
R1/R2
RESISTENZA 2,2k 1/2W
T1
TRASFORMATORE 0-230-400V/0-24V 5,5VA
R3
RESISTENZA 47 OHM 1/4W
F1
FUSIBILE 500mA
R4
RESISTENZA 10k 1/4W
D1
RADDRIZZATORE 1A
K1
RELE’ DI COMANDO 24Vcc OMRON
D2
DIODO
K2
MINICONTATTORE 24Vcc ABB
L1
LED LINEA VERDE
S1
PULSANTE STOP
L2
LED MARCIA BIANCO
S2
PULSANTE START
C1
CONDENSATORE ELETTROLITICO 220 F 35V
S3
PROTEZIONE DISCO COPRILAMA
C2
CONDENSATORE ELETTROLITICO 220 F 35V
No DISEGNO
S 2232
DATA
27-05-99
TENSIONE: 230V-50Hz
Black
Grey
Green
Blue
Brown
Circuit diagram RP-M351CE
Red
5.5
MACCHINA
RP-M351CE
RP-M254CE/RP-M304CE
RP-M354CE/RP-M374CE
RP-M353CE/RP-M373CE
Ci riserviarno la proprieta’a termini di legge di questo disegno con divieto di riprodurlo anche in parte o di renderlo noto a terzi.
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
5-7
5 — Operation
5-8
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
Section 6
Technical Information
Table of Contents:
page no
6.1
6.2
6.3
6.4
6.5
Adjustment of thickness plate
Sharpener settings/adjustments RP-M251CE/RP-M301CE
Sharpener settings/adjustments RP-M351CE
Transmission belt - replacement/tensioning
Product holder replacement
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
6-3
6-5
6-7
6-9
6-11
6-1
6 — Technical Information
6-2
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
6 — Technical Information
6.1
Adjustment of thickness plate
Figure 6-1 Adjustment of thickness plate
1.
Loosen the two screws (4) and move the thickness plate to within
1 - 1.5 mm of the knife (2), as shown in Figure 6-1.
2.
Fasten the thickness plate in position by firmly tightening the two
screws (4).
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
6-3
6 — Technical Information
Figure 6-2 Adjustment of thickness plate
As a result of shocks during transport, the thickness plate may sometimes come
into contact with the knife; to re-set the thickness plate proceed as follows:
6-4
1.
Lift the machine and loosen the screw (4) on the bracket (3).
2.
Slowly rotate the thickness plate until the center of curvature of the edge
next to the blade coincides with the centre of the knife, with an even
opening of 1 - 1.5 mm between the knife and the thickness plate, as shown
above.
3.
Fasten the thickness plate by tightening the screw (4) firmly.
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
6 — Technical Information
6.2
Sharpener settings/adjustments RP-M251CE/RP-M301CE
The knife must be replaced when its diameter falls to 10 mm less than its nominal
value. The reduction of the knife diameter could mean that a corrective
adjustment of the sharpener is needed. It should be positioned as follows:
1.
Lift up the protection cover (pos 1 fig 6.3) and rotate the sharpener into its
sharpening position (fig 6.3).
2.
Loosen the two screws (pos 1 fig 6.3); loosen the bolt (spanner 22) (pos 3)
and remove the sharpener assembly (pos 4).
3.
Rotate the bolt (pos 5 fig 6.4) clockwise as far as is necessary, and
assemble the sharpener assembly by checking that both stones are
positioned as in fig 6.5, with the finishing stone parallel to the knife (fig 6.3);
check that there is no interference with the movable protection (pos 6
fig 6.3). Put the sharpener into its non-operational position and check that
there is no interference between the finishing stone and the knife. Fix the
sharpener assembly by fastening the bolt (pos 3 fig 6.3).
4.
Reset the knob (pos 2 fig 6.3) and fasten the two screws (pos 1 fig 6.3).
Figure 6-3
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
6-5
6 — Technical Information
Figure 6-4
Figure 6-5
6-6
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
6 — Technical Information
6.3
Sharpener settings/adjustments RP-M351CE
The knife must be replaced when its diameter falls to 10 mm less than its nominal
value. The reduction of the knife diameter could mean that a corrective adjustment
of the sharpener is needed. It should be positioned as follows:
1.
Lift up the protection cover (pos 1 fig 6.6) and rotate the sharpener into its
sharpening position (pos 2).
2.
Remove the caps (pos 2 and 3 fig 6.6); loosen the grain (pos 4 fig 6.7) and
lower the sharpener until both stones are positioned in relation to the knife
as shown in figs 2 and 2, and then fasten the grain (pos 4).
3.
Loosen the grain (pos 5 fig 6.7); put the sharpener into its non-operational
position (fig 6.6), and rotate the cam (pos 6 fig 6.7) anti-clockwise as far as
possible. Loosen the grain (pos 8) and rotate the eccentric cam clockwise or
anticlockwise (pos 9 fig 2) and check that the movable protection (pos 7
fig 6.6) projects beyond the knife edge, as shown in fig 6.6a, and then fasten
the grain (pos 8 fig 6.7).
4.
Return the sharpener to its sharpening position (fig 6.7) and rotate the cam
clockwise (pos 6 fig 6.7), checking that there is no interference between the
trimming stone and the movable protection (pos 7 fig 6.7) during the rotation,
and then fasten the grain (pos 5).
Figure 6-6a
Figure 6-6
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
6-7
6 — Technical Information
Figure 6-7
Figure 6-8
6-8
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
6 — Technical Information
6.4
Transmission belt - replacement/tensioning
Before starting any operations disconnect the plug.
Remove the blade with the blade removal tool.
Operations
1.
Disassembly and removal of the transmission and motor.
2.
Replacement and adjustment of the belt.
Figure 6-9
1.
Disassembly and removal of the transmission and the motor.
a.
Unscrew knob (A) and remove the blade cover.
b.
Remove the outer bushing (B) by loosening the screw which holds it
to the bushing (C).
c.
Unscrew and remove the bushing (C) from the pin (D).
d.
Remove the blade.
e.
Remove the bottom cover.
e.
Disconnect the electrical wiring.
f.
Unscrew the 3 screws (P) fixing the motor/transmission to the casting
and remove the motor.
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
6-9
6 — Technical Information
Figure 6-10
2.
6 - 10
Replacement and adjustment of the belt.
a.
Mark the eccentric cam (E), in relation to its seat and notice the
dimension(s).
b.
Remove the screw (G), which holds the eccentric cam in its seat by
using a key, as shown above.
c.
Rotate the eccentric cam in its seat in order to draw the motor nearer
to the transmission axis.
d.
Replace the transmission belt (H).
e.
Restore the eccentric cam in its original position (refer to the
reference mark made earlier) and set the dimension(s) to the value
noted earlier, and tighten the screw (G). Reassemble by following the
reverse of the disassembly procedure.
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
6 — Technical Information
6.5
Product holder replacement
1
2
3
4
5
Product holder clamping handle
Product holder support
Carriage
Bed plate
Upper fixing screw
6
7
8
9
10
Stop nut
Threaded locking ring
Alignment pin
Bush
Support
Figure 6-11
1.
Stop the carriage (3) at the end near the operator.
2.
Place the product holder on the carraige (3) so that the upper fixing screw
(5) sits on the support (10).
3.
Loosen the threaded locking ring (7).
4.
Turn the product holder clamping handle to the right to release the carriage.
5.
Tighten the threaded locking ring (7).
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
6 - 11
6 — Technical Information
6 - 12
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
Section 7
Appendices
Table of Contents:
page no
7.1
7.2
7.3
7.4
7.5
7.6
7.7
Slicer model coding system
Routine maintenance
7.2.1
Cleaning
7.2.2
Knife control
7.2.3
Knife sharpening
7.2.4
Lubrication
7.2.5
Sliding of the food holding carriage
7.2.6
Endgrip sliding
7.2.7
Supply cord
7.2.8
Service checklist
Options
7.3.1
Option 8
Digital portioner
7.3.2
Options 12, 22 Vegetable chute 135/180 mm dia
7.3.3
Option 78
Carriage with dual fixing grippers (350)
7.3.4
Option 91
Vegetable arm
7.3.5
Option 93
Carriage with dual fixing grippers (250/300)
7.3.6
Options 81, 100 Product fence 55/20 mm high
Recommended parts
7.4.1
RP-M251CE/M301CE
7.4.2
RP-M351CE
Exploded views with part numbers
7.5.1
RP-M251CE/M301CE
7.5.2
RP-M351CE
Knife remover assemblies
Knife part numbers
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
7-3
7-4
7-4
7-4
7-4
7-4
7-4
7-4
7-4
7-5
7-6
7-6
7-7
7-8
7-9
7-10
7-11
7-12
7-12
7-13
7-14
7-14
7-21
7-32
7-40
7-1
7 — Appendices
7-2
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
7 — Appendices
7.1
Slicer model coding system
Product hierarchy
Knife size
Approvals
RP - M 25 4 CE Combi
Operation
Configuration
Weighing
Product hierarchy
RT
RP
RM
RE
=
=
=
=
Range Top
Range Professional
Range Mid
Range Economy
Operation
M
A
S
F
=
=
=
=
Manual
Semi automatic
Stacker
Fully automatic
Knife size
22
25
27
30
35
37
=
=
=
=
=
=
220
250
275
300
350
370
Configuration Table
1
2
3
4
5
P
E
=
=
=
=
=
=
=
Gravity feed with standard table
Straight feed with standard table (with standard pusher)
Straight feed with articulating arm clamp
Straight feed with sliding inner table
Straight feed with top clamp
Premier gravity feed with standard table
Economy gravity feed with standard table
Approvals
CE =
ETL =
CSA =
Std. =
CE approvals
USA approvals
Canadian approvals
Standard non CE product
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
7-3
7 — Appendices
7.2
Routine maintenance
7.2.1
Cleaning
The slicer should be cleaned often; at least once a day. To clean all accessible
parts, use a cloth moistened with water and detergent (a non aggressive one): do
not use water jets! For effective cleaning follow the instructions given in the
Instruction Manual.
7.2.2
Knife control
Check the knife diameter and replace the knife when its diameter is 10mm less
than its nominal diameter; for the replacement of the knife look at the specific
technical sheet.
7.2.3
Knife sharpening
When the slicing is not satisfactory, it is necessary to sharpen the knife. Before
sharpening the knife clean the sharpening stone. If the sharpening is not
satisfactory replace both stones.
7.2.4
Lubrication
This operation should be made after the cleaning of the slicer, or each time when
the carriage does not slide smoothly; use Berkel slicer oil.
7.2.5
Sliding of the food holding carriage
If the carriage does not slide smoothly, lubricate its sliding bar as indicated in the
Instruction Manual.
7.2.6
Endgrip sliding
If the endgrip does not slide smoothly, lubricate its sliding bar as indicated in the
Instruction Manual.
7.2.7
Supply cord
Check periodically for wear of the supply cord: if you see that there are evident
cuts, replace immediately.
7-4
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
7 — Appendices
7.2.8
Service checklist
Machine: Slicer
1
Check for noise and faults, liaise with operators.
2
Check meat table assembly/carriage/pusher plate, ensure safety guards
studs and screw function properly, lubricate assembly as necessary.
3
Remove knife plate checking screws and handles, check and adjust
distance between centre plate and knife and the inner rim of knife to
outside edge of centre of plate.
4
Clean back of knife adjust sharpener/sharpen knife.
5
Remove slice deflector, check tightness of adjustment plate, check and
adjust distance between deflector and back of knife.
6
Remove knife with correct tool, lubricate knife shaft.
7
Check drive belts for tension and replace as necessary.
8
Lubricate slider bar and wheel rail, replace buffers as necessary.
9
Check electrical safety of machine.
10
Rebuild machine and realign gauge plates.
11
Ensure machine functions correctly after complete service.
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
7-5
7 — Appendices
7.3
Options
7.3.1
Option 8
7-6
Digital portioner
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
7 — Appendices
7.3.2
Option 12, 22 Vegetable chute 135/180 mm dia
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
7-7
7 — Appendices
7.3.3
7-8
Option 78
Carriage with dual fixing grippers (350)
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
7 — Appendices
7.3.4
Option 91
Vegetable arm
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
7-9
7 — Appendices
7.3.5
7 - 10
Option 93
Carriage with dual fixing grippers (250/300)
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
7 — Appendices
7.3.6
Option 81, 100
Product fence 55/20 mm high
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
7 - 11
To order a part in RED suffix the part
number with /RED i.e. I2040/RED
7 — Appendices
7 - 12
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
7 — Appendices
7.4
Recommended parts
7.4.1
RP-M251CE/M301CE
Part No.
Description
M251CE
M301CE
A1027
Sharpener assembly
1
1
C4813
Belt
1
1
E1420
Cam
1
1
I1682
On/off switch - membrane type
1
1
I1990A/Red
Index knob assembly
1
1
I2040/Red
End grip handle
1
1
I2095/Red
Knob assembly - carriage support
1
1
L060203
Knife 250mm
1
-
L061203
Knife 300mm
-
1
M6601
Grinding stone
2
2
M6622
De-burr stone
2
2
M8356
Motor 220/240V 50Hz
1
1
P1019
Washer (pusher slide bar)
6
6
P1034
Plastic stop (pusher)
1
1
P1124
Slice deflector
1
-
P1134
Slice deflector
-
1
P5008
Foot
4
4
S3290
Circuit board
1
1
S3802
Index arm
1
1
T5119/Red
Centre plate knob assembly
1
1
T8044
Knife shaft assembly
1
1
V7014X
Knife screw
4
4
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
7 - 13
7 — Appendices
7.4.2
7 - 14
RP-M351CE
Part No.
Description
M351CE
A1026
Sharpener assembly
1
E1420
Cam
1
I1680
On/off switch - membrane type
1
I1990A/Red
Index knob assembly
1
I2040/Red
End grip handle
1
I2095/Red
Knob assembly - carriage support
1
L062303
Knife 350mm
1
M6602
Grinding stone
2
M6621
De-burr stone
2
M8469
Motor
1
P1019
Washer (pusher slide bar)
6
P1034
Plastic stop (pusher)
1
P3381
Grinding stone/spindle assembly
1
P3458
De-burr stone/spindle assembly
1
P5008
Foot
4
R2001
Motor start block
1
S3227
Circuit board
1
S3815
Index arm
1
T5006/Red
Centre plate knob assembly
1
T8027
Knife shaft - bronze gear
1
V7014X
Knife screw
4
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
7 — Appendices
7.5
Exploded views with part numbers
7.5.1
RP-M251CE/M301CE
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
7 - 15
To order a part in RED suffix the part
number with /RED i.e. I2040/RED
7 — Appendices
7 - 16
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
To order a part in RED suffix the part
number with /RED i.e. I2040/RED
7 — Appendices
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
7 - 17
To order a part in RED suffix the part
number with /RED i.e. I2040/RED
7 — Appendices
7 - 18
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
To order a part in RED suffix the part
number with /RED i.e. I2040/RED
7 — Appendices
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
7 - 19
To order a part in RED suffix the part
number with /RED i.e. I2040/RED
7 — Appendices
7 - 20
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
To order a part in RED suffix the part
number with /RED i.e. I2040/RED
7 — Appendices
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
7 - 21
To order a part in RED suffix the part
number with /RED i.e. I2040/RED
7 — Appendices
7 - 22
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
7 — Appendices
7.5.2
RP-M351CE
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
7 - 23
To order a part in RED suffix the part
number with /RED i.e. I2040/RED
7 — Appendices
7 - 24
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
To order a part in RED suffix the part
number with /RED i.e. I2040/RED
7 — Appendices
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
7 - 25
To order a part in RED suffix the part
number with /RED i.e. I2040/RED
7 — Appendices
7 - 26
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
To order a part in RED suffix the part
number with /RED i.e. I2040/RED
7 — Appendices
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
7 - 27
To order a part in RED suffix the part
number with /RED i.e. I2040/RED
7 — Appendices
7 - 28
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
To order a part in RED suffix the part
number with /RED i.e. I2040/RED
7 — Appendices
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
7 - 29
To order a part in RED suffix the part
number with /RED i.e. I2040/RED
7 — Appendices
7 - 30
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
To order a part in RED suffix the part
number with /RED i.e. I2040/RED
7 — Appendices
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
7 - 31
To order a part in RED suffix the part
number with /RED i.e. I2040/RED
7 — Appendices
7 - 32
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
7 — Appendices
To order a part in RED suffix the part
number with /RED i.e. I2040/RED
Sharpener
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
7 - 33
To order a part in RED suffix the part
number with /RED i.e. I2040/RED
Valid from
01-12-98 to 30-06-99
7 — Appendices
Sharpener
7 - 34
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
To order a part in RED suffix the part
number with /RED i.e. I2040/RED
Valid from 01-07-99
7 — Appendices
Sharpener
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
7 - 35
To order a part in RED suffix the part
number with /RED i.e. I2040/RED
7 — Appendices
7 - 36
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
7 — Appendices
To order a part in RED suffix the part
number with /RED i.e. I2040/RED
Motor
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
7 - 37
To order a part in RED suffix the part
number with /RED i.e. I2040/RED
7 — Appendices
7 - 38
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
To order a part in RED suffix the part
number with /RED i.e. I2040/RED
7 — Appendices
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
7 - 39
7 — Appendices
7.6
Knife remover assemblies
for CE models only
Knife Diameter
7.7
Part Number
220 mm
SER/BER/0151
250 mm
A2508300
300 mm
A3024300
350 mm
SER/BER/0125
Part numbers for knives
Knife
Diameter
Standard
knife
Stainless
steel
Standard knife with
remover holes
220mm
L 0611
250mm
L 0602
L 060202
L 060203
300mm*
L 0606
L 060602
L 060603
300mm
L 0612
350mm
L 0623
L 062302
370mm
L 0610
L 061002
Stainless steel knife
with remover holes
L 060207
L 060607
L 061203
L 062303
L 062307
*For model RP-M304CE only
7 - 40
Service Instructions RP-M251CE/RP-M301CE/RP-M351CE
You local service agent is:
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising