Thuraya IP Commander Quick Start Guide

Thuraya IP Commander Quick Start Guide
Copyright 2015 SRT Wireless, LLC. All rights reserved. Published 2015.
Install SIM Cards
Printed in the United States of America
SRT and SRT Wireless are trademarks of SRT Wireless, LLC in the United
States and other countries.
Wi-Fi®, Wi-Fi Alliance®, the Wi-Fi CERTIFIED™ logo, the Wi-Fi logo, WMM®
and the Wi-Fi ZONE logo are registered trademarks of the Wi-Fi Alliance;
Wi-Fi CERTIFIED™, the Wi-Fi Alliance logo, Wi-Fi ZONE, WPA, WPA2, Wi-Fi
PROTECTED SET-UP and Wi-Fi Protected Set-up logo are trademarks of
the Wi-Fi Alliance. IEEE Std 802.11-2007 is a trademark of the Institute of
Electrical and Electronics Engineers, Inc. Ethernet is a registered trademark of Ethernet Alliance, Inc. Thuraya is a registered trademark of
Thuraya Satellite Telecommunications Company. Adobe and Acrobat are
Refer to callouts in illustration above.
Open access panel and install voice and IP SIM cards:
registerd trademarks of Adobe Systems Incorporated in the United States
Item
and/or other countries.
All other trademarks or registered trademarks of products mentioned in
❶
Remove six
screws from
access panel
Using a cross-point screwdriver, remove the six
screws holding the side access panel in place.
❷
Remove
access panel
Remove panel and set aside.
❸
Remove gasket if needed
If the gasket remains completely in place,
don’t remove it. If it does come loose, set it
aside.
❹
Install SIMcard
this document are the property of their respective owners.
Information in this document is subject to change without notice. The software described in this document is furnished under a license agreement
or nondisclosure agreement. The software may be used or copied only in
accordance with the terms of those agreements. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in
any form or any means electronic or mechanical, including photocopying
and recording for any purpose other than the purchaser's personal use
without the written permission of SRT Wireless, LLC.
Procedure
SRT Wireless, LLC
4101 SW 47th Ave., Suite 102
Davie, FL 33322
With the panel removed, note the three
openings on the side of the enclosure. The
Primary SIM card goes into the center opening (labeled PRIMARY).
Insert the Primary SIM into the center opening slot. The SIM card is spring-loaded.
Push until you feel it snap into place. To
remove, press until you feel the card
release (a mechanical snap), then remove.
www.thuraya.com
www.srtwireless.net
Close and seal access panel:
920-00276 - 10/12/2015
Item
Procedure
❸
Replace
gasket
Carefully place gasket into the groove it was
removed from. Gasket must be completely
inside the groove with no overhang.
❷
Replace access Place the access panel over the area it was
panel
removed from. Align the screw holes in the
panel with the ones on the enclosure.
❶
Insert and
tighten screws
Insert the screws into the appropriate holes.
Tighten hand tight to ensure the plate is
properly aligned. Tighten the rest of the way
down with a cross-point screwdriver. Do not
overtighten!
Thuraya® IP Commander
Front Panel Indicators
Congratulations on your purchase of a Thuraya IP
Commander terminal, which gives you voice and IP
services, no matter where you go within the Thuraya
service area.
Please take a moment to review this Quick Start
Guide to help familiarize yourself with this sophisticated and powerful product.
If you require more detailed information about your
Thuraya IP Commander, please refer to the user
guide, SRTW part number 920-00275, an Adobe®
Acrobat® PDF file, which is located on the DocumentMedia CD supplied with this product.
Thuraya IP Commander product installation instructions, SRTW part number 920-00299, are provided in
an Adobe Acrobat PDF file on the Document-Media
CD supplied with this product.
The Front Panel
SUP
Power Supply is connected - Green
ON
IP Commander is powered on - Green
ACT
Activity on the satellite link - Red (blinking with satellite activity)
SAT
Thuraya Antenna sees satellite - Green
Thuraya Antenna DOES NOT see Satellite - Red
GPS
GPS satellites in view - Green
GPS satellites NOT in view - Red
ANT
Thuraya Antenna functional - Green
Thuraya Antenna not functional - Red
LAN
Change Device Mode
To switch between VOICE and IP modes, log onto the
IP Commander web page (see IP Commander Web
Pages in the center column). Click Home under the
General heading. Click the radio button related to the
IP Profile mode you wish to change to, located within
the Change Mode box (Voice or one of the IP modes),
and click Connect. In a few moments, you are
switched to the desired Device Mode. For details,
please refer to the IP Commander user guide, SRTW
part number 920-00275.
Set Up IP Commander
Setup is easy. All you need, other than the contents of
the transport case, is a power source.
❶
Local Area Network visible - Green
Local Area Network NOT visible - Red
❷
IP Commander Web Pages
This is where you adjust wired and Wi-Fi network settings, set up connection profiles, change passwords,
update firmware, and view the status of the
IP Commander device.
❶ Wi-Fi® Antenna Connector: Connect the Wi-Fi
“whip” antenna to this connector.
CAUTION: Do not overtighten the connector!
❷ Thuraya Antenna Connector: This connector
provides power and a signal path to and from the
Thuraya Antenna.
❸ Thuraya Handset Connector: This permits you to
make calls over your IP Commander device using the
specially modified handset.
To access the web page, once you have connected your
IP Commander device to your computer, type
http://192.168.1.254. The login screen is displayed.
The default login is admin, and the default password is
admin. Please change these to something more
secure as soon as possible. To do so, refer to the Password section of the IP Commander User Guide
(SRTW part number 920-00275) for instructions.
❸
❻ Status Indicator Panel: Tell at a glance if the
IP Commander is working properly.
❼ Power/Reset Button: Press and release to apply
power to the IP Commander. Press and hold the button to shut the IP Commander down, or to restart if
malfunctioning.
❹
❶
Connect whip antenna to SMA connector. NOTE: SMA connector is fragile. Tighten only finger tight!
❷
Connect the supplied rf coaxial cable between the IP Commander and the Thuraya Antenna. Ensure that the antenna
has a clear view of the sky. Do not kink or otherwise damage
the cable.
❸
Connect and lock the connector on the Thuraya handset cable
to the IP Commander at the location shown in item ❸. The
handset is powered by the IP Commander. It uses the SIM
cards installed inside the IP Commander housing.
❹
Connect and lock the power supply or mobile power adapter
connector to the power connector on the IP Commander.
❺
Connect and lock the armored end of the RJ-45 Ethernet cable
to the IP Commander and the other to your PC or network.
❹ Power Input: Connect either a 120 VAC to 240
VAC, 50-60 Hz power supply, or a 12 V mobile
DC power adapter.
❺ Ethernet Connector: Connect a standard RJ-45
Ethernet cable between the IP Commander and a
PC or other network device.
❺
When everything is connected, apply power, wait a
few minutes to acquire a signal from the Thuraya
satellite, and you’re ready to go.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising