758CSV Owner s Manual
758CSV
WEIGHT INDICATOR
With Body Mass Index Features
Owner’s Manual
8555-M433-O1 Rev J
11/12
Cardinal Scale Manufacturing Co.
PO BOX 151 WEBB CITY, MO 64870
PH (417) 673-4631 - FAX (417) 673-5001
www.detectoscale.com
Technical Support:
Ph: 866-254-8261
x techsupport@cardet.com
8555-M433-O1
Rev J y 758CSV
Owner’s
Printed in USA
1
2
8555-M433-O1 Rev J y 758CSV Owner’s
TABLE OF CONTENTS
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Standard Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Optional Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EUROPEAN DECLARATION OF CONFORMITY. . . . . . . . . . . . . . . . . . . . . . . . .
SITE PREPARATION REQUIREMENTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTERCONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Optional AC Power Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Height Rod Option – Detecto DHR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Load Cell . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
USB, Serial & Ethernet Interface Specifications . . . . . . . . . . . . . . . . . . . . . . . .
Serial I/O Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ethernet (758-IPOption) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BATTERIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Battery Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Low Battery Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Battery Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Battery Installation/Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
KEYPAD FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Basic Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Body Mass Index Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ANNUNCIATORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Basic Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Basic Operation with ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Body Mass Index Operation
(Using Mechanical Height Rod or Manually Entering Height) . . . . . . . . . . . .
Body Mass Index Operation with ID
(Using Mechanical Height Rod or Manually Entering Height) . . . . . . . . . . . .
Body Mass Index Operation (Using Digital Height Rod) . . . . . . . . . . . . . . . . . .
Body Mass Index Operation with ID (Using Digital Height Rod) . . . . . . . . . . . .
SETUP AND CALIBRATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SETUP REVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PRINTER TICKET FORMATS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WEIGHT ON DEMAND FORMATS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SERIAL AND USB DEVICE PORT COMMANDS . . . . . . . . . . . . . . . . . . . . . . . .
ERROR AND STATUS DISPLAYS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BEFORE YOU CALL SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EVENT COUNTER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CARE AND CLEANING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECURITY SEAL INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PARTS IDENTIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8555-M433-O1 Rev J y 758CSV Owner’s
Page 1
Page 1
Page 1
Page1
Page 2
Page 3
Page 4
Page 4
Page 4
Page 5
Page 5
Page 5
Page 5
Page 5
Page 5
Page 6
Page 6
Page 6
Page 7
Page 7
Page 7
Page 7
Page 8
Page 8
Page 9
Page 11
Page 13
Page 13
Page 14
Page 15
Page 15
Page 16
Page 17
Page 19
Page 30
Page 31
Page 32
Page 33
Page 35
Page 35
Page 36
Page 36
Page 37
Page 39
I1
FCC COMPLIANCE STATEMENT
WARNING! This equipment generates uses and can radiate radio frequency and if not
installed and used in accordance with the instruction manual, may cause interference to radio
communications. It has been tested and found to comply with the limits for a Class A
computing device pursuant to Subpart J of Part 15 of FCC rules, which are designed to provide
reasonable protection against such interference when operated in a commercial environment.
Operation of this equipment in a residential area may cause interference in which case the
user will be responsible to take whatever measures necessary to correct the interference.
You may find the booklet “How to Identify and Resolve Radio TV Interference Problems”
prepared by the Federal Communications Commission helpful. It is available from the U.S.
Government Printing Office, Washington, D.C. 20402. Request stock No. 001-000-00315-4.
PROPER DISPOSAL
When this device reaches the end of its useful life, it must be properly disposed of. It must not
be disposed of as unsorted municipal waste. Within the European Union, this device should
be returned to the distributor from where it was purchased for proper disposal. This is in
accordance with EU Directive 2002/96/EC. Within North America, the device should be
disposed of in accordance with the local laws regarding the disposal of waste electrical and
electronic equipment.
It is everyone’s responsibility to help maintain the environment and to
reduce the effects of hazardous substances contained in electrical and
electronic equipment on human health. Please do your part by making
certain that this device is properly disposed of. The symbol shown to the
right indicates that this device must not be disposed of in unsorted
municipal waste programs.
All rights reserved. Reproduction or use, without expressed written permission, of editorial or
pictorial content, in any manner, is prohibited. No patent liability is assumed with respect to
the use of the information contained herein. While every precaution has been taken in the
preparation of this manual, the Seller assumes no responsibility for errors or omissions.
Neither is any liability assumed for damages resulting from use of the information contained
herein. All instructions and diagrams have been checked for accuracy and ease of application;
however, success and safety in working with tools depend to a great extent upon the individual
accuracy, skill and caution. For this reason the Seller is not able to guarantee the result of any
procedure contained herein. Nor can they assume responsibility for any damage to property or
injury to persons occasioned from the procedures. Persons engaging the procedures do so
entirely at their own risk.
Serial Number ______________________
PRECAUTIONS
Date of Purchase ___________________
Before using this indicator, read this manual
and pay special attention to all "WARNING"
symbols:
Purchased From ____________________
___________________________________
___________________________________
___________________________________
IMPORTANT
RETAIN THIS INFORMATION FOR FUTURE USE
II
2II
8555-M433-O1 Rev J y 758CSV Owner’s
ELECTRICAL
WARNING
INTRODUCTION
Thank you for purchasing our Model 758CSV Weight Indicator. It has been manufactured with
quality and reliability at our factory in Webb City, MO USA. This Indicator has been tested
before leaving our factory to insure accuracy and dependability for years to come.
This manual is provided to guide you through installation, operation and maintenance of your
indicator. Please read it thoroughly before attempting to install or operate your 758CSV and
keep it handy for future reference.
SPECIFICATIONS
Power Requirements . . . . . . . . 6 “C” cell Ni-Cad or NiMH batteries (not included) OR an
optional 100 to 240 VAC 50/60Hz 12 VDC 1A wall plug-in
UL/CSA listed AC power adapter. Refer to list in PARTS
IDENTIFICATION section of this manual.
Operating Temperature . . . . . . -10 to +40 ºC
Display . . . . . . . . . . . . . . . . . . . Weight: Five digit, seven segment, 13 mm high LCD
Height: Four digit, seven segment, 10 mm high LCD
Sensitivity . . . . . . . . . . . . . . . . . 1.2 uV/division (0 to 3.0 mV/V), Class III
Signal Input Range . . . . . . . . . 0 to 15mV max.
Transducer Excitation . . . . . . . 5.0 VDC
Number of Load Cells . . . . . . . up to 4 each 350:
Load Cell Cable Length . . . . . . 3 meters max.
Resolution . . . . . . . . . . . . . . . . 5,000 divisions
Capacities . . . . . . . . . . . . . . . . 1,000 to 5,000 divisions commercial
up to 10,000 divisions noncommercial
Division Value . . . . . . . . . . . . . 1, 2, 5 or 10 x 1, 0.1, 0.01, 0.001
Sample Rate . . . . . . . . . . . . . . 1 to 10 samples per second selectable
Auto Zero Range . . . . . . . . . . . 0.5 or 1 through 9 divisions
Weighing Units . . . . . . . . . . . . . kilograms
Keyboard . . . . . . . . . . . . . . . . . Membrane type with 19 keys
Enclosure Size . . . . . . . . . . . . . 24 cm W x 17 cm H x 5 cm D
Construction . . . . . . . . . . . . . . . Painted Steel
Standard Features:
x
x
x
Auto Shut-Off Feature
Selectable Sleep-Mode
Selectable Filtering
x
x
x
Serial I/O (Input/Output)
USB Device Port
Height Rod Port (for Optional Detecto
Digital Height Rod)
x
x
Optional 12VDC AC Power Adapter
Optional Welch Allyn® WAConnect
Optional Features:
x
x
758-IP Ethernet Option
Detecto DHR (Digital Height Rod)
8555-M433-O1 Rev J y 758CSV Owner’s
1
EUROPEAN DECLARATION OF CONFORMITY
Manufacturer: Cardinal Scale Manufacturing Company
PO Box 151
203 East Daugherty
Webb City, Missouri 64870 USA
Telephone No. 417-673-4631
Fax No.
417-673-5001
Product:
Non-automatic Weight Indicating Instrument
Model Numbers 758CSV
Serial Number EXXXYY-ZZZ
where XXX = day of year
YY = last two digits of year
ZZZ = sequential number
The undersigned hereby declares, on behalf of Cardinal Scale Manufacturing Company of
Webb City, Missouri, that the above-referenced product, to which this declaration relates, is
in conformity with the provisions of:
Council Directive 2006/95/EC Low Voltage Directive
Test Report Number 0206-1 Cardinal Scale Mfg. Co.
European Standard EN55022: Class B for radiated emissions
European Standard EN61000-4-3: Class A for Radiated EMC
European Standard EN61000-4-6: Class A for Conducted Disturbances
Test Report Number 020424-537 Criterion Technology
Council Directive 90/384/EEC (20 June, 1990) on the Harmonization
of the Laws of Member States relating to non-automatic Weighing
Systems as amended by:
Council Directive 93/68/EEC (22 July, 1993)
Certificate of EU Type Approval Number: UK 2655
The Technical Construction File required by this Directive is maintained at the corporate
headquarters of Cardinal Scale Manufacturing Company, 203 East Daugherty, Webb City,
Missouri.
_____________________
Mark Levels
Quality Assurance Administrator
2
8555-M433-O1 Rev J y 758CSV Owner’s
SITE PREPARATION REQUIREMENTS
The Model 758CSV Weight Indicator is a precision weight indicating instrument. As with any
precision instrument, it requires an acceptable environment to operate at peak performance
and reliability. This section is provided to assist you in obtaining such an environment.
Environmental
The Model 758CSV Weight Indicator meets or exceeds all certification requirements within a
temperature range of -10 to +40 °C.
In order to keep cooling requirements to a minimum, the indicator should be placed out of
direct sunlight and to provide adequate air circulation, keep the area around the indicator clear.
Do not place the indicator directly in front of a heating or cooling vent. Such a location will
subject the indicator to sudden temperature changes, which may result in unstable weight
readings.
Insure that the indicator has good, clean AC power and is properly grounded. In areas subject
to lightning strikes, additional protection to minimize lightning damage, such as surge
suppressors, should be installed.
Electrical Power
The 758CSV indicator has been designed to operate from a 100 to 240 VAC 50/60Hz 12 VDC
1A wall plug-in UL/CSA listed AC power adapter. Note that a special order is not required for
operation at 230 VAC.
ƒ
The socket-outlet supplying power to the indicator should be on a separate circuit from the
distribution panel and dedicated to the exclusive use of the indicator.
ƒ
The socket-outlet shall be installed near the equipment and shall be easily accessible.
ƒ
The wiring should conform to national and local electrical codes and ordinances and should
be approved by the local inspector to assure compliance.
ƒ
On installations requiring 230 VAC power, it is the responsibility of the customer to have
a qualified electrician install the proper power adapter plug that conforms to national
electrical codes and local codes and ordinances.
8555-M433-O1 Rev J y 758CSV Owner’s
3
INSTALLATION
Unpacking
Carefully remove indicator from shipping carton and inspect it for any damage that may have
taken place during shipment. Keep carton and packing material for return shipment if it should
become necessary. The purchaser is responsible for filing all claims for any damages or loss
incurred during transit.
Should your indicator come already installed on a scale, the following installation
information does not apply to you.
Bracket Mount
Screws
Latch
Release
Latch
Battery Door
Thumb Screw
Figure No. 1
Mounting
The indicator may be mounted (using an optional bracket) to a desktop, table or bench. It can
be mounted on a wall using the two (2) holes in the mounting bracket and two (2) #10 screws
placed 51 mm apart in the wall.
To install indicator on bracket, push latch release down flush with back of indicator and hold.
Next, place large end of slotted holes in bracket over screw heads on back of indicator. Pull
down to secure indicator. Release latch release to lock indicator to bracket. See Figure No. 1.
Regardless of how and where you mount indicator, it should be in a safe area where it will not
be in the way of normal traffic. The location chosen should be free of temperature extremes
and water, is not subject to direct sunlight and should be mounted where the display is easily
viewed and within easy reach of the operator.
If wall mounted, make certain the structure and mounting bolts are of sufficient strength to
support the indicator. The mounting bracket should be securely fastened to the wall so it
cannot break loose.
4
8555-M433-O1 Rev J y 758CSV Owner’s
INSTALLATION, CONT.
INTERCONNECTIONS
All input, output, options and power connections to the 758CSV are made at the rear panel of
the indicator. Connections for the Load Cell input and the Serial I/0 are made using 9-pin "D"
shaped connectors. The Height Rod option (Detecto DHR, Digital Height Rod) and Ethernet
(758-IP) options use snap-in modular connectors. The USB port is a device (or upstream) port
using an industry standard “B” connector. The optional 12VDC wall plug-in UL/CSA listed AC
power adapter is connected using a power jack. Refer to Figure No. 1.
Optional AC Power Adapter
To power the 758CSV using the optional 12VDC wall plug-in AC power adapter, connect the
plug from the adapter into the power jack on the back of the indicator and then plug the power
adapter into the proper electrical outlet. Refer to Figure No. 1. On models requiring 220 VAC,
it is the customer’s responsibility to obtain the correct power adapter plug.
Height Rod – Detecto DHR (Digital Height Rod) Option
The optional Detecto DHR (Digital Height Rod) connects to the 758CSV by a snap-in modular
connector socket. Insert the modular connector of the DHR cable into the socket on the rear of
the display it locks in place (a clicking sound will be heard when it is locked in place).
Load Cell
The load cell cable connects to the 758CSV via a 9-pin "D" connector
on the rear panel of the indicator. Figure No. 2 shows the pin
identification for the load cell connector. Make certain that the pins
are correctly identified before soldering a wire to them. Use the
connector retaining screws to hold the load cell cable connector
securely to the rear panel.
5
9
PIN NO.
1
2
3
4
5
FUNCTION
+EXCITATION
-SIGNAL
No Connection
No Connection
SHIELD
PIN NO.
6
7
8
9
FUNCTION
-EXCITATION
+SIGNAL
No Connection
No Connection
4
8
3
7
2
6
MATING CONNECTOR INFORMATION
DESCRIPTION
ITEM
CONNECTOR
DE9-P
CONNECTOR SHELL C883010001
1
Cardinal Part #
6610-2379
6610-1131
USB
Figure No. 2
The USB port is a device (or upstream) port and uses readily
available cables with the industry standard “B” connector.
USB, Serial and Ethernet Interface Specifications
The 758CSV USB, Serial and optional Ethernet interfaces can be configured during the setup
and calibration procedure or during the setup review operation. Using either method, it is
possible to select the operation of the interfaces.
The interfaces may be connected to a computer for transmission of weight and associated
data to a PC-based EMR (electronic medical record) software program. The data can be
transmitted on demand (pressing the PRINT/ENTER key) or on receipt of a command from the
computer. Note that only the serial interface can be connected to a printer to record weight
and associated data.
8555-M433-O1 Rev J y 758CSV Owner’s
5
INSTALLATION, CONT.
Serial I/O Port
The 758CSV RS-232 serial I/O port is a 9-pin "D" connector on the
rear panel of the indicator. Figure No. 3 shows the Serial I/0
connector along with the identity of the pins used. Make certain that
the pins are correctly identified before soldering a wire to them. Use
the connector retaining screws to hold the serial cable connector
securely to the rear panel.
PIN NO.
FUNCTION
2
DATA INPUT (RXD)
3
DATA OUTPUT (TXD)
5
SIGNAL GROUND (GND)
5
9
4
8
3
Note that pins 1, 4 and 6 through 9 are not used.
The 758CSV RS-232 serial interface can be configured during the
setup and calibration procedure or during the setup review operation.
Using either method, it is possible to select the operation of the serial
interface as well as select the baud rate.
x
x
x
The baud rates supported are: 1200, 2400, 4800, 9600, 19.2K
and 38.4K baud.
The data format is fixed at 8 bits, No parity, and 1 stop bit.
The indicator is shipped from the factory with the baud rate set
to 9600 baud.
7
2
6
1
Figure No. 3
Ethernet (Optional)
The 758CSV Ethernet option requires the purchase of the optional 758-IP Ethernet Interface
Option. Once installed, connections to the 758CSV are by CAT 5 or equivalent cable. Consult
your network administrator for the proper procedure to terminate and connect the cable.
BATTERIES
The 758CSV indicator can use 6 "C" size Ni-Cad or NiMH batteries (not included). You must
first obtain and install batteries before operations can begin. Batteries are contained in a
battery holder inside indicator. Access is via a removable panel on back of indicator.
IMPORTANT! All 6 batteries must be of the same type. They must be all Ni-Cad or
all NiMH. DO NOT mix Ni-Cad or NiMH batteries.
CAUTION! The 758CSV has internal circuitry that when used in conjunction with the
AC power adapter, recharges the Ni-Cad or NiMH batteries. Because the 758CSV
has this charging capability, you CAN NOT use non-rechargeable batteries in it.
CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT
TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
ATTENTION: RISQUE D'EXPLOSION SI LA BATTERIES EST REMPLACE'E PAR UN
TYPE INCORRECT. REJETEZ LES BATTERIES UTILISE'ES SELON LES
INSTRUCTIONS.
6
8555-M433-O1 Rev J y 758CSV Owner’s
INSTALLATION, CONT.
Battery Status
If batteries are used, the indicator will show battery status on power up. The display will show
battry then change to ð YY ð, where YY indicates remaining battery voltage expressed as a
percentage (%) of total battery voltage
Low Battery Indicator
When batteries are near the point they need to be recharged, a low battery annunciator on the
display will turn on. (See Figure No. 5 or 6). If the battery voltage drops too low for accurate
weighing, the indicator will automatically shut off and you will be unable to turn it back on.
When the low battery annunciator turns on, plug the AC power adapter into the indicator and
then into the proper electrical wall outlet. The indicator will begin charging the batteries.
Battery Charging
To recharge the Ni-Cad or NiMH batteries, the AC power adapter must be connected to an AC
power outlet and plugged into the indicator. It will take approximately 6 hours to fully recharge
the batteries in the indicator. While the batteries are charging the indicator can still be
operated. Note that charging the batteries for more than 6 hours will not damage them.
Battery Installation/Replacement
To install or remove the batteries, the following steps should be followed:
1. Make sure the AC power adapter is unplugged.
2. Remove the indicator from the mounting bracket and turn the indicator over so that the
display is facing away from you.
3. Locate the rectangular panel on the back of indicator and remove the thumb screw.
4. Remove the panel (lift straight up and slide it out) exposing the battery holder.
5. If installing new batteries, proceed to step 6. If replacing the batteries, remove all 6
batteries from the battery holder and then proceed to step 6.
6. Install the new 6 "C" size batteries in the holder, noting the polarity markings located in
the battery holder. Refer to Figure No. 4.
7. After placing all 6 batteries in holder, replace panel on back of indicator (slide tab into
slot on rear panel) and install thumb screw.
8. Turn the indicator over (display facing up) and press the ON/OFF key.
9. If display turns on, batteries have been installed correctly. If not, remove panel and
check for one or more improperly positioned batteries.
10. Return the indicator to the mounting bracket.
11. The indicator is now ready for operation.
Figure No. 4
8555-M433-O1 Rev J y 758CSV Owner’s
7
KEYPAD FUNCTIONS
The membrane keypad is not to be operated with pointed objects (pencils,
pens, fingernails, etc). Damage to keypad resulting from this practice is NOT
covered under warranty.
Figure No. 5
This is the ON/OFF key. With the indicator off, pressing this key will apply
power to the indicator and turn on the display. If the indicator is already on,
pressing the key again will turn the indicator off.
Basic Functions
This is the ZERO key. It is used to reset the display to zero up to the selected
limit of either 4% or 100% of the scale capacity. The zero limit is set during
setup and calibration of the indicator.
This is the UNITS key. It is not currently used.
8
8555-M433-O1 Rev J y 758CSV Owner’s
KEYPAD FUNCTIONS, CONT.
This is the LOCK/RELEASE key. It is used to lock and unlock the display. If
the HOLD feature was enabled during setup and calibration, pressing this key
(after obtaining a stable weight value) will cause the indicator to lock onto the
weight. Pressing this key a second time will unlock the display and return the
weight display to zero.
If the AUTO LOCK feature was enabled, the weight display will lock after
placing a load on the scale and obtaining a stable weight value. Pressing this
key will unlock the display and return the weight display to zero, or if another
load is applied to the scale, lock onto the new weight after obtaining a stable
weight value. NOTE: The lock feature is for non-commercial (NOT "Legal for
Trade") applications.
Body Mass Index (BMI) Functions
This is the NET/GROSS key. It is used to toggle between Net and Gross
weight modes. The selected mode is indicated by turning on the appropriate
annunciator on the display. Note that if no valid tare weight has been entered,
pressing this key will cause a momentary display -Err- and the indicator will
remain in the Gross weight mode.
This is the TARE key. It is a dual function key. Pressing it and pressing the
PRINT/ENTER key (Pushbutton Tare mode) will cause the current gross
weight to be stored as the new tare weight and change the weight display to
the net weight display mode (Net annunciator will turn on). Pressing this key,
entering a numeric value (Keypad Tare) and then pressing the PRINT/ENTER
key will cause the value entered to be accepted as the new tare weight.
NOTE: Tare weights equal to or greater than scale capacity cannot be entered.
In addition, the keypad tare weight division value must be the same as the scale
division value. For example, a unit with .05 kg as the division value will display
-Err- if you attempt to enter 1.03 for the tare weight.
This is the ID/HEIGHT key. It is used to display and enter an identification (ID)
number for use in the ID Storage feature and for entering the height and for the
Body Mass Index (BMI) calculation.
Pressing this key will change the display to show the currently selected
identification (ID) number and allow the entry of a new ID number.
The identification (ID) number can be up to 11 digits. When entering an ID
number, the digits start displaying on the right side of the ID display and
proceed to the left. When an ID greater than 4 digits is used, the digits will
automatically scroll off the left side of the display to show the additional digits
on the right as they are entered.
This is the CLEAR key. It is used to clear an incorrect entry from the display
without processing the data. If an incorrect entry is made, press the CLEAR
key and re-enter the correct data. When entering the ID, pressing the CLEAR
key will act as a “backspace” key (it will back up one space and delete the
character in that space). NOTE: The CLEAR key must be pressed before the
PRINT/ENTER key to ensure the data is not processed.
8555-M433-O1 Rev J y 758CSV Owner’s
9
KEYPAD FUNCTIONS, CONT.
This is the PRINT/ENTER key. It serves several purposes. First, when
reviewing setup parameters, pressing the PRINT/ENTER key will display the
current setting of the parameter. Second, the PRINT/ENTER key is used to
signal completion of the data entry and causes the indicator to process the
data entered. Third, the PRINT/ENTER key is used to initiate the transmission
of weight and associated data using the selected I/O port.
NOTE: The indicator will not respond to pressing the PRINT/ENTER key unless
the weight display is stable. If displaying gross weight, only the gross weight is
printed. If displaying net weight, the gross, tare, and net weights are printed. If
the ID and BMI features are used, their data is printed along with the weight data.
The 0 through 9 numeric keys are used to enter numeric data
during the setup and calibration as well as during normal
operation of the indicator.
NOTE: The 0 and 1 keys have
dual functions. They are used to
enter numeric data during setup
and calibration as well as during
normal operations and are also
used to select yes or no to
various prompts.
nControl Feature
The 758CSV includes support for nControl. nControl
is a PC based program that can design a ticket then
download the ticket information to the indicator. The
758CSV allows 1 programmable format instead of the
ASCII format default ticket.
For more information on nControl, refer to the
nControl Fast Start Guide.
Time, dd/mm/yy
ID:
BMI:
Height:
Weight:
xxxxxxxxxxx
xx.x
xx.x cm
xxx.xuu G
xxx.xuu PT
xxx.xuu N
SAMPLE TICKET
NOTE: If the ID/HEIGHT key is disabled, the appropriate field will be left out when
printing a ticket.
10
8555-M433-O1 Rev J y 758CSV Owner’s
ANNUNCIATORS
The annunciators are turned on to indicate that the display is in the mode corresponding to the
annunciator label or that the status indicated by the label is active.
Figure No. 6
LO BAT
The LO BAT (low battery) annunciator is used with the battery operation. It will turn ON to
indicate that the batteries will soon need to be replaced. No change in operation will occur
until just before the battery voltage drops to a level where operation is affected. At this level,
the indicator will automatically turn itself off.
GROSS
The GROSS annunciator is turned on to show that the weight displayed is the gross weight.
Gross weight will be displayed when no tare weight value is stored.
TARE
The TARE annunciator is turned on to show that the indicator is in a weight mode in which a
known tare (container) weight value is stored.
NET
The NET annunciator is turned on to show that the weight displayed is the net weight. Net
weight is determined by subtracting the stored tare weight from the gross weight. The tare
weight is usually the weight of the empty container. Note that the NET annunciator is only
active when a tare weight value is stored.
[\ (STABLE)
The (Stable) annunciator is turned on when the weight display is stable. When off, it means
that the change in successive weight samples is greater than the motion limits selected during
setup and calibration of the indicator.
ZERO
The ZERO annunciator is turned on to indicate that the weight is within +/- 1/4 division of the
center of zero.
LOCK
The LOCK annunciator is turned on to show that the indicator is locked onto the weight. In
operation after obtaining a stable weight value, pressing the LOCK/RELEASE key (or
resetting the Auto Lock) will cause the indicator to lock onto the weight and turn on the
annunciator. Pressing the LOCK/RELEASE key a second time (or dropping below the Auto
Lock reset value) will unlock the display and turn off the annunciator.
NOTE: The lock feature (Hold Mode) must be enabled during setup and calibration.
8555-M433-O1 Rev J y 758CSV Owner’s
11
ANNUNCIATORS, CONT.
kg
The kg annunciator is turned on to indicate that the displayed weight is in kilograms.
cm
The cm annunciator is turned on to indicate that the displayed height measurement is in
centimeters.
BODY MASS INDEX
The BODY MASS INDEX annunciator is turned on when displaying
the calculated body fat. The bar graph is used to show a graphical
representation (ranging from Low to High) of the Body Mass Index
calculation.
12
8555-M433-O1 Rev J y 758CSV Owner’s
OPERATION
Basic Operation
To Weigh
1. Press ON/OFF key to turn indicator on.
2. Press ZERO key to zero weight display. ZERO, GROSS and kg annunciator will
turn on to show that the scale is ready for use.
3. Place patient on scale and read weight display.
4. If a printer is connected to scale, press PRINT/ENTER key to print a ticket.
5. Remove patient from scale.
Zero Weight Display
1. In Gross Weight mode (GROSS annunciator on), press ZERO key.
2. Weight display will return to zero. ZERO and STABLE [\ annunciators will turn on
to show a stable, center-of-zero gross weight condition.
Push Button Tare (Tare weight is NOT known)
1. In Gross Weight mode (GROSS annunciator
IMPORTANT! Tare entry is not
on), place item (wheelchair, walker, etc…) to
allowed if Auto Hold is enabled.
be tared on scale.
2. Press TARE key.
3. Display will show weight of item on scale and TARE annunciator will turn on.
4. Press PRINT/ENTER key.
5. Display will change to 0.0 and NET annunciator will turn on to show that net weight
is being displayed. The item's weight has been entered as "tare weight".
6. Proceed with weighing operation.
Tare Weight Entry (Tare weight is known)
1. In Gross Weight mode (GROSS annunciator on), press TARE key.
2. Display will show zero or previously entered tare and TARE annunciator will turn on.
3. If weight displayed is acceptable, press PRINT/ENTER key to save it. Otherwise,
use the numeric keys and enter a new tare weight. Note that when entering tare
weights, a maximum of 4 digits can be entered and the numbers advance from right
to left in the display. The number of leading or trailing zeros required to obtain your
desired tare is dependent upon the DIVISION VALUE selected in the setup
procedure.
For example:
Division Value:
Desired Tare Value:
Key Sequence:
0.1
1.5 kg
15
4. After the new tare weight has been entered, press PRINT/ENTER key.
5. Display will show a minus Net weight and NET annunciator will turn on.
6. Proceed with weighing operation.
Tare Weight Recall
1. In Net Weight mode (NET annunciator on), press TARE key.
2. Display will show previously entered tare for approximately 1 second and then return
to Net Weight mode (NET annunciator on).
To Clear the Tare Weight
1. Press NET/GROSS key to return to Gross weight mode.
2. Remove all material from scale platform and press ZERO key. This will reset tare
weight to zero.
8555-M433-O1 Rev J y 758CSV Owner’s
13
OPERATION, CONT.
Basic Operation with ID
To Weigh
1. Press ON/OFF key to turn indicator on.
2. Press ZERO key to zero weight display. ZERO, GROSS and kg annunciator will
turn on to show scale is ready for use.
3. Press ID/HEIGHT key.
4. Display will change to show id=.
5. Using numeric keys, key-in up to an 11 digit identification number.
6. Press PRINT/ENTER key.
7. Place patient on scale
8. Read weight display.
9. If a printer is connected to scale, press PRINT/ENTER key to print a ticket.
10. Remove patient from scale.
Push Button Tare (Tare weight is NOT known)
1. In Gross Weight mode (GROSS annunciator
IMPORTANT! Tare entry is not
on), place item (wheelchair, walker, etc…) to
allowed if Auto Hold is enabled.
be tared on scale.
2. Press TARE key.
3. Display will show weight of item on scale and TARE annunciator will turn on.
4. Press PRINT/ENTER key.
5. Display will change to zero and NET annunciator will turn on to show that net weight
is being displayed. The item's weight has been entered as "tare weight".
6. Press ID/HEIGHT key.
7. Display will change to show id=.
8. Using numeric keys, key-in up to an 11 digit identification number.
9. Press PRINT/ENTER key.
10. Proceed with weighing operation.
Tare Weight Entry (Tare weight is known)
1. In Gross Weight mode (GROSS annunciator on), press TARE key.
2. Display will show 0.0 or previously entered tare and TARE annunciator will turn on.
3. If weight displayed is acceptable, press PRINT/ENTER key to save it. Otherwise,
use the numeric keys and enter a new tare weight. Note that when entering tare
weights, a maximum of 4 digits can be entered and the numbers advance from right
to left in the display. The number of leading or trailing zeros required to obtain your
desired tare is dependent upon the DIVISION VALUE selected in the setup
procedure.
For example:
1.
2.
3.
4.
5.
6.
7.
14
Division Value:
Desired Tare Value:
Key Sequence:
0.1
1.5 kg
15
After the new tare weight has been entered, press PRINT/ENTER key.
Display will show a minus Net weight and NET annunciator will turn on.
Press ID/HEIGHT key.
Display will change to show id=.
Using numeric keys, key-in up to an 11 digit identification number.
Press PRINT/ENTER key.
Proceed with weighing operation.
8555-M433-O1 Rev J y 758CSV Owner’s
OPERATION, CONT.
Body Mass Index (BMI) Operation
Using Mechanical Height Rod or Manually Entering Height
1. Press ON/OFF key to turn indicator on.
2. Press ZERO key to zero weight display. ZERO, GROSS and kg annunciator will
turn on to show scale is ready for use.
3. Perform tare operation if required. Refer to Push Button Tare or Tare Weight Entry in
previous section for instructions on using tare.
4. Place patient on the scale and then press ID/HEIGHT key.
5. Display will change to show Cn=_.
6. Use numeric keys to enter up to 4 digits (# # # . #) for height in centimeters and then
press PRINT/ENTER key.
7. Read weight and BMI displays.
8. If a printer is connected to scale, press PRINT/ENTER key to print a ticket.
9. Remove patient from scale.
10. If Tare operation was performed, press NET/GROSS key to return to Gross weight
mode.
11. Press ZERO key. This will reset tare weight to zero.
12. BMI display will clear when weight returns to zero.
Body Mass Index (BMI) Operation with ID
Using Mechanical Height Rod or Manually Entering Height
1. Press ON/OFF key to turn indicator on.
2. Press ZERO key to zero weight display. ZERO, GROSS and kg annunciator will
turn on to show scale is ready for use.
3. Press ID/HEIGHT key.
4. Display will change to show id=.
5. Using numeric keys, key-in up to an 11 digit identification number.
6. Press PRINT/ENTER key.
7. Display will change to show Cn=_.
8. Using numeric keys enter up to 4 digits (# # # . #) for height in centimeters and then
press PRINT/ENTER key.
9. Perform tare operation if required. Refer to Push Button Tare or Tare Weight Entry
in previous section for instructions on using tare.
10. Place patient on scale.
11. Read weight and BMI displays.
12. If a printer is connected to scale, press PRINT/ENTER key to print a ticket.
13. Remove patient from scale.
14. If Tare operation was performed, press NET/GROSS key to return to Gross
weight mode.
15. Press ZERO key. This will reset tare weight to zero.
16. BMI display and ID will clear when weight returns to zero.
8555-M433-O1 Rev J y 758CSV Owner’s
15
OPERATION, CONT.
Body Mass Index (BMI) Operation with DHR
Using Digital Height Rod
IMPORTANT! Before performing the operations on this page, the digital height
rod must be in its “starting position” (inner sliding tube must be down
completely inside outer stationary tube and headpiece folded flat against
stationary tube) prior to turning on the indicator. Otherwise, the error
message 999.9 will be displayed.
1. Make sure height rod is in starting position.
2. Press ON/OFF key to turn indicator on.
3. Press ZERO key to zero weight display. ZERO, GROSS and kg annunciator will
turn on to show scale is ready for use. Note that height reading will show 110.0 cm.
4. Perform tare operation if required. Refer to Push Button Tare or Tare Weight Entry
in previous section for instructions on using tare.
5. Place patient on the scale.
6. Grasp height rod at hinge pin (see Figure No. 7) and raise
it well above patient’s head and then lift headpiece to
horizontal position. Carefully lower height rod until
headpiece rests on top of patient’s head.
7. BMI will automatically be displayed with height.
8. Read weight, height and BMI displays.
9. If height rod was used, while holding headpiece horizontal,
raise height rod well above patient’s head.
10. Remove patient from scale and return height rod to starting
position.
11. If Tare operation was performed, press NET/GROSS key
to return to Gross weight mode.
12. Press ZERO key. This will reset tare weight to zero.
13. BMI display will clear when weight returns to zero.
16
8555-M433-O1 Rev J y 758CSV Owner’s
Figure No. 7
OPERATION, CONT.
Body Mass Index (BMI) Operation with ID and DHR
Using Digital Height Rod
IMPORTANT! Before performing the operations on this page, the digital height
rod must be in its “starting position” (inner sliding tube must be down
completely inside outer stationary tube and headpiece folded flat against
stationary tube) prior to turning on the indicator. Otherwise, the error
message 999.9 will be displayed.
1. Make sure height rod is in starting position.
2. Press ON/OFF key to turn indicator on.
3. Press ZERO key to zero weight display. ZERO, GROSS and kg annunciator will
turn on to show scale is ready for use. Note that height reading will show 110.0 cm.
4. Perform tare operation if required. Refer to Push Button Tare or Tare Weight Entry
in previous section for instructions on using tare.
5. Press ID/HEIGHT key.
6. Display will change to show id=.
7. Using numeric keys, key-in up to an 11 digit identification number.
8. Press PRINT/ENTER key.
9. Place patient on scale.
10. Grasp height rod at hinge pin (see Figure No. 8) and raise
it well above patient’s head and then lift headpiece to
horizontal position. Carefully lower height rod until
headpiece rests on top of patient’s head.
11. BMI will automatically be displayed with height.
12. Read weight, height and BMI displays.
13. If a printer is connected to scale, press PRINT/ENTER key
to print a ticket.
14. If height rod was used, while holding headpiece horizontal,
raise height rod well above patient’s head.
15. Remove patient from scale and return height rod to starting
position.
Figure No. 8
16. If Tare operation was performed, press NET/GROSS key
to return to Gross weight mode.
17. Press ZERO key. This will reset tare weight to zero.
18. BMI display and ID will clear when weight returns to zero.
8555-M433-O1 Rev J y 758CSV Owner’s
17
18
8555-M433-O1 Rev J y 758CSV Owner’s
SETUP AND CALIBRATION
Your 758CSV Indicator has been thoroughly tested and calibrated before being shipped to
you. If you received the indicator with a scale, calibration is not necessary. If the indicator is
being connected to a scale for the first time or recalibration is necessary for other reasons,
proceed as indicated.
Calibration and Setup of the indicator is accomplished entirely by
the keypad. To enter the setup and calibration mode:
1. With the power off, remove the 2 screws from the right
end cap (as viewed from the indicator back) and remove
the end cap.
2. Locate the calibration jumper J2 on the circuit board and
remove the jumper. See Figure No. 9.
3. With the jumper removed, press and hold the
LOCK/RELEASE key and then press the ON/OFF key.
4. The indicator will perform a display test (turn on all digits),
show the software version for a few seconds and then
change to show SETUP.
5. Release the LOCK/RELEASE key.
6. The display will change to setgC.
7. The indicator is now ready for setup and calibration
Calibration
Jumper J2
Figure No. 9
During the setup and calibration process it is necessary to enter operational parameters via the
indicator's keypad. The following keys and the numeric keypad are used to input the values.
ON/OFF
PRINT/ENTER
NO
YES
1. Pressing the PRINT/ENTER key without entering a new value will retain the current
setting and advance to the next prompt.
2. Some prompts require only a YES or NO selection.
3. Other prompts require a numeric value to be entered. Use the numeric keypad to enter
the new value.
4. In either case, pressing the PRINT/ENTER key after changing a setting will save the new
value and advance to the next prompt.
CAUTION! The membrane keypad is not to be operated with pointed
objects (pencils, pens, fingernails, etc). Damage to keypad resulting from
this practice will NOT be covered under warranty.
setgC (SET GRAVITY CONSTANT)
This indicator is equipped with an acceleration of gravity function which means that it can be
calibrated in one location and then adjusted to match the acceleration of gravity at the
location where it will used.
With display showing setgC, press PRINT/ENTER key to show current setting. If setting
displayed is acceptable, press PRINT/ENTER key to save it. Otherwise use numeric keys
0/NO or 1/YES and enter a new setting. Press PRINT/ENTER key to save it.
0 = Gravity Constant is NOT used
1 = Set Gravity Constant
NOTE: If you select 1 (Set Gravity Constant) two additional prompts will be displayed.
8555-M433-O1 Rev J y 758CSV Owner’s
19
SETUP AND CALIBRATION, CONT.
CALgC (CALIBRATED GRAVITY CONSTANT)
With display showing CALgC, press PRINT/ENTER key to show current setting. This is the
acceleration of gravity value of the location where the scale was calibrated.
If the value displayed is acceptable, press PRINT/ENTER key to save it. Otherwise, using
numeric keys, enter a new value and then press PRINT/ENTER key to save it. Consult the
factory Tech Support for the Acceleration of Gravity value for your location.
OPgC= (OPERATING GRAVITY CONSTANT)
With display showing OPgC=, press PRINT/ENTER key to show current setting. This is the
acceleration of gravity value for the location where the scale will be operated.
If setting displayed is acceptable, press PRINT/ENTER key to save it. Otherwise, using
numeric keys, enter a new value and then press PRINT/ENTER key to save it. Consult the
factory Tech Support for the Acceleration of Gravity value for your location.
IMPORTANT! Once the Gravity Constant has been set, both CALgC
and oPgC= must be set to the same value to disable it.
int= (INTERVAL SETTING)
Press PRINT/ENTER key to show current setting. If value displayed is acceptable, press
PRINT/ENTER key to save it. Otherwise, using numeric keys, enter a new value and then
press PRINT/ENTER key to save it. Allowable values are 1, 2, 5 or 10.
NOTE: If you select an interval value of 10 (int=10), dPP= prompt will not be shown.
Setup will proceed to CAP=, scale capacity setting prompt.
Unit= (WEIGHING UNIT)
With display showing Unit=, press PRINT/ENTER key to show current setting. If value
displayed is acceptable, press PRINT/ENTER key again to save it. Otherwise, using numeric
keys, enter a new value and then press PRINT/ENTER key to save it.
0 = None
1 = Pounds Only
2 = Kilograms Only
3 = Pounds/Kilograms
4 = Kilograms/Pounds
5 = Ounces Only
6 = Grams Only
7 = Stones and Pounds
or Kilograms
IMPORTANT! If Unit=7 (7 = Stones and Pounds or Kilograms) is selected, the value
selected for int= (Scale Interval) and dPP= (Decimal Point Position) must be set to (1).
NOTE: Weight display for Stones and Pounds/Kilograms mode is XX.YY.Y,
where XX is weight in Stones and YY.Y is remainder of the weight in pounds.
Please note that in this mode, "ST" and "lb" annunciators will be turned on.
dPP= (DECIMAL POINT POSITION)
With display showing dPP=, press PRINT/ENTER key to show current setting. If value
displayed is acceptable, press PRINT/ENTER key to save it. Otherwise, using numeric keys,
enter a new value and then press PRINT/ENTER key to save it.
0 = XXXXXX
20
1= XXXXX.X
2 = XXXX.XX
3 = XXX.XXX
8555-M433-O1 Rev J y 758CSV Owner’s
SETUP AND CALIBRATION, CONT.
CAP= (SCALE CAPACITY)
With display showing CAP=, press PRINT/ENTER key to show current setting. If value
displayed is acceptable, press PRINT/ENTER key to save it. Otherwise, using numeric keys,
enter a new value and then press PRINT/ENTER key to save it. Allowable values are 1
through 99,999.
CAL= (CALIBRATION)
With display showing CAL=, press PRINT/ENTER key. Display will change to show current
setting 0 (0=NO). If scale has been previously calibrated and you wish to skip calibration and
proceed to trA=, Zero Tracking Range, simply press PRINT/ENTER key and internal
calibration factor will be retained.
To begin calibration, press 1/YES key to select yes and then press PRINT/ENTER key. After
pressing PRINT/ENTER key display will change to LOAd=.
LOAd= (LOAD CALIBRATION WEIGHT)
Display will change to LOAd= which is a prompt for entry of calibration weight value and
placement of this amount of test weights on scale platform.
1. Make certain scale platform is empty and free of debris.
2. Place the desired amount of calibrated test weights on scale platform. A minimum of
50% of scale's capacity is required. However 70% to 100% is recommended.
3. Press PRINT/ENTER key.
4. If the value displayed is acceptable, press the PRINT/ENTER key again. Otherwise,
determine the exact amount of test weights to be placed on scale platform, then using
numeric keys, enter this value.
5. Verify that the numbers entered are the same as the amount of test weights and then
press the PRINT/ENTER key.
6. Starting at the left and proceeding right, a series of dashes will appear on the display.
The dashes will stay on the display momentarily, then disappear, after which the display
will proceed to the UnLOd prompt.
UnLOd= (UNLOAD CALIBRATION WEIGHT)
With display showing the UnLOd prompt:
1. Remove the weights from the scale platform and then press the PRINT/ENTER key.
2. Starting at the left and preceding right, a series of dashes will appear on the display.
The dashes will stay on the display momentarily, then disappear, after which the
calibration factor will be saved and the display will proceed to the trA= prompt.
trL= (FOUR PERCENT ZERO TRACKING RANGE LIMIT)
This setting determines whether a 4% limit is placed on zero tracking and push button zero
and selects the format when printing the date.
If enabled, (trL= 1) zero tracking and push button zero is limited to 4 % of scale capacity
and the date format is dd/mm/yy.
If disabled, (trL= 0) zero tracking and push button zero will operate up to full scale
capacity and the date format is mm/dd/yy.
With display showing trL=, press PRINT/ENTER key to show current setting. If setting
displayed is acceptable, press the PRINT/ENTER key to save it. Otherwise use numeric
keys 0/NO or 1/YES and enter a new setting. Press PRINT/ENTER key to save it.
8555-M433-O1 Rev J y 758CSV Owner’s
21
SETUP AND CALIBRATION, CONT.
UnS= (UNSTABLE RANGE)
The Unstable Range is the number of divisions of change permitted before the STABLE
annunciator turns off.
With display showing Un5=, press PRINT/ENTER key to show current setting. If value
displayed is acceptable, press PRINT/ENTER key to save it. Otherwise, using numeric keys,
enter a new value and then press PRINT/ENTER key to save it. Allowable values are 1
through 9.
FLt= (DIGITAL FILTER LEVEL SELECTION)
Display will change to show FLt= (prompt for selection of digital filtering level). Your
indicator will arrive with factory filter settings (1 = minimal) entered. Please check with your
scale service technician should you wish to change filter level and break range.
Press PRINT/ENTER key to show current setting. If value displayed is acceptable, press
PRINT/ENTER key to save it. Otherwise, using numeric keys, enter a new value and then
press PRINT/ENTER key to save it. Note, that if you select 3 (Custom Filtering) two
additional prompts will be displayed.
0 = Disabled – NO Filtering
1 = MINIMAL FILTERING
2 = MODERATE FILTERING
3 = CUSTOM FILTERING
NOTE: The prompts, F= (Filter Level) and br= (Break Range) will only be displayed if
you select 3 (Custom Filtering) for the FLt= Digital Filter Level.
F= (FILTER LEVEL)
With Custom Filtering selected, the display will change to show FL= (Filter Level). Filter
level is a number from 1 (least) to 16 (greatest) that corresponds to the amount of filtering.
Press PRINT/ENTER key to show current setting. If value displayed is acceptable, press
PRINT/ENTER key to save it. Otherwise, using numeric keys, enter a new value and then
press PRINT/ENTER key to save it. Allowable values are 1 through 16.
br= (BREAK RANGE)
The Break Range is a number from 1 to 64 that corresponds to the number of division
changes to break out of filtering.
With display showing br=, press PRINT/ENTER key to show current setting. If value
displayed is acceptable, press PRINT/ENTER key to save it. Otherwise, using numeric
keys, enter a new value and then press PRINT/ENTER key to save it. Allowable values are
1 through 64.
Sr= (SAMPLE RATE)
With display showing Sr=, press PRINT/ENTER key to show current setting. If value
displayed is acceptable, press PRINT/ENTER key to save it. Otherwise, using numeric keys,
enter a new value and then press PRINT/ENTER key to save it. The sample rate may be set
from a minimum of 1 sample per second to a maximum of 10 samples per second in one
sample per second intervals. Allowable values are 1 through 10.
22
8555-M433-O1 Rev J y 758CSV Owner’s
SETUP AND CALIBRATION, CONT.
HOLd= (HOLD MODE)
With display showing HOLd=, press PRINT/ENTER key to show current setting. If value
displayed is acceptable, press PRINT/ENTER key to save it. Otherwise, using numeric keys,
enter a new value and then press PRINT/ENTER key to save it.
0 = NO (disable)
1 = YES (enable)
2 = AUTO (Automatic Hold)
x
If HOLd=0 or1 (NO or YES) is selected, proceed to type= (Type) section.
x
If HOLd= 2 (AUTO) is selected, an additional prompt bAnd= (Auto Lock Reset Band)
will be displayed and the tYPE= (Operation Mode) prompt will not be shown. The
operation mode will automatically be set to 0 (Transaction Storage Mode). Proceed to
bAnd= (Auto Lock Reset Band) to continue setup.
With Hold feature enabled (HOLd=1), the indicator will lock the displayed weight on the
display when LOCK/RELEASE key is pressed. Pressing the key again will unlock display.
If automatic hold (HOLd=2) is selected, the indicator will automatically lock the weight on the
display after obtaining a stable weight value that exceeds the Auto Lock Reset Band value.
Refer to the next prompt Auto Lock Reset Band.
IMPORTANT! HOLD mode of operation is only used in non-commercial
applications and must be set to 0 = NO (disabled) for "Legal for Trade"
applications.
bAnd= (AUTO LOCK RESET BAND)
If Automatic Lock is selected, display will change to show bAnd= (Auto Lock Reset Band
value). This is the number of division changes needed to reset the auto lock. For Automatic
Lock to function, load on scale must rise above bAnd= value (and remain stable). To release
Automatic Lock, load on scale must fall below bAnd= value. At that point, next weighing
operation can begin.
Press PRINT/ENTER key to show current setting. If value displayed is acceptable, press
PRINT/ENTER key to save it. Otherwise, using numeric keys, enter a new value and then
press PRINT/ENTER key to save it. Allowable values are: 0 through 99.
type= (STORAGE OPERATION MODE)
This setting determines whether the indicator operates in the Transaction Storage Mode (no
ID storage) or in the ID Storage Mode. Note that the ID Storage Mode allows up to 99 ID’s.
With the display showing tYPE=, press the PRINT/ENTER key to show current setting. If the
setting displayed is acceptable, press the PRINT/ENTER key to save it. Otherwise, using the
numeric keys, 0/NO or 1/YES, enter the new setting, then press the PRINT/ENTER key to
save it.
0 = Transaction Storage
1 = ID Storage Enabled
8555-M433-O1 Rev J y 758CSV Owner’s
23
SETUP AND CALIBRATION, CONT.
HirES= (High Resolution Mode)
The High Resolution Mode feature will display the weight at 10 times the standard resolution.
For example, a 758CSV configured for 200 kg x 0.1 kg will display weight in high resolution
mode at 200 kg x 0.01 kg.
With the display showing HirES=, press the PRINT/ENTER key to show current setting. If
the setting displayed is acceptable, press the PRINT/ENTER key to save it. Otherwise, using
the numeric keys, 0/NO or 1/YES, enter the new setting, then press the PRINT/ENTER key to
save it.
0 = NO (If High Resolution Weight
mode is not desired)
1 = YES (If High Resolution Weight
mode is desired)
NOTE: If HirES=1 (YES) is selected, the indicator will exit Setup and Calibration,
reset and then display weight in the High Resolution Weight mode.
To return to Setup and Calibration:
1. Press the ON/OFF key.
2. Press and hold the LOCK/RELEASE key and then press the ON/OFF key.
3. The indicator will perform a display test (turn on all digits), show the software
version for a few seconds and then change to show SETUP.
4. Release the LOCK/RELEASE key.
5. The display will change to setgC.
6. The indicator is now ready to continue setup and calibration from the beginning.
trA= (ZERO TRACKING RANGE)
Zero tracking range is a value in scale divisions that will be automatically zeroed off. With the
display showing trA=, press PRINT/ENTER key to show current setting. If value displayed
is acceptable, press PRINT/ENTER key to save it. Otherwise, using numeric keys, enter a
new value and then press PRINT/ENTER key to save it. Allowable values are 1 through 18
(1 to 9 divisions by 0.5 divisions). Enter a 0 (zero) to disable zero tracking.
allyn= (WELCH ALLYN)
This setting determines whether the USB port of the indicator is interfaced to a Welch Allyn
device (with an activated license). NOTE: Must purchase WACONNECT (which includes a
license key and USB cable) from Detecto to initiate connectivity with the Welch Allyn device.
With display showing Allyn=, press PRINT/ENTER key to show current setting. If setting
displayed is acceptable, press PRINT/ENTER key to save it. Otherwise use numeric keys
0/NO or 1/YES and enter a new setting. Press PRINT/ENTER key to save it.
0 = NO, Indicator is NOT interfaced to
Welch Allyn device
1 = YES, Indicator IS interfaced to
Welch Allyn device
nin= (MINUTES)
With display showing nin=, press PRINT/ENTER key to show current setting. If value
displayed is acceptable, press PRINT/ENTER key to save it. Otherwise, using numeric keys,
enter a new value and then press PRINT/ENTER key to save it. Allowable values are: 0
through 59.
24
8555-M433-O1 Rev J y 758CSV Owner’s
SETUP AND CALIBRATION, CONT.
HH= (HOURS)
With display showing hh=, press PRINT/ENTER key to show current setting. If value
displayed is acceptable, press PRINT/ENTER key to save it. Otherwise, using numeric keys,
enter a new value and then press PRINT/ENTER key to save it. Allowable values are: 0
through 23.
NOTE: Time is entered in a 24-hour format. When entering times after noon (12:00 PM),
you must add 12 to time. For example, 3:00 PM would be entered as 15.
dd= (DAY)
With display showing dd=, press PRINT/ENTER key to show current setting. If value
displayed is acceptable, press PRINT/ENTER key to save it. Otherwise, using numeric keys,
enter a new value and then press PRINT/ENTER key to save it. Allowable values are: 1
through 31.
nn= (MONTH)
With display showing nn=, press PRINT/ENTER key to show current setting. If value
displayed is acceptable, press PRINT/ENTER key to save it. Otherwise, using numeric keys,
enter a new value and then press PRINT/ENTER key to save it. Allowable values are: 1
through 12.
yy= (YEAR)
With display showing yy=, press PRINT/ENTER key to show current setting. If value
displayed is acceptable, press PRINT/ENTER key to save it. Otherwise, using numeric keys,
enter a new value and then press PRINT/ENTER key to save it. Allowable values are: 00
through 99.
iD= (ID NUMBER FEATURE)
This setting determines whether the indicator allows an ID number to be entered prior to
beginning the weighing operation. This applies to both Basic Operation and with the BMI
feature enabled.
With display showing id=, press PRINT/ENTER key to show current setting. If setting
displayed is acceptable, press PRINT/ENTER key to save it. Otherwise use numeric keys
0/NO or 1/YES and enter a new setting. Press PRINT/ENTER key to save it.
0 = ID Disabled
1 = ID Enabled
iDBAR= (ID SCANNER)
This setting determines whether the indicator allows a scanner to be used to input an ID
number to be entered prior to beginning the weighing operation. This applies to both Basic
Operation and with the BMI feature enabled.
With display showing idbar=, press PRINT/ENTER key to show current setting. If setting
displayed is acceptable, press PRINT/ENTER key to save it. Otherwise use numeric keys
0/NO or 1/YES and enter a new setting. Press PRINT/ENTER key to save it.
0 = No Scanner
1 = Yes Scanner
IMPORTANT! If the Transaction Storage Mode is set to ID Storage Enabled (type= 1)
the idbar= prompt will not be displayed.
8555-M433-O1 Rev J y 758CSV Owner’s
25
SETUP AND CALIBRATION, CONT.
Htr= (DIGITAL HEIGHT ROD)
This setting determines whether the height rod port is enabled for the Detecto DHR (Digital
Height Rod). With the port enable and the height rod connected, the BMI will automatically
be calculated and displayed when the height rod is raised and placed on the patient’s head.
With display showing Htr=, press PRINT/ENTER key to show current setting. If setting
displayed is acceptable, press PRINT/ENTER key to save it. Otherwise use numeric keys
0/NO or 1/YES and enter a new setting. Press PRINT/ENTER key to save it.
0 = Height Rod Port is Disabled
1 = Height Rod Port is Enabled
bni= (BMI CALCULATION FEATURE)
This setting determines whether the indicator operates as a basic (weigh calculation only)
indicator or performs the Body Mass Index (BMI) calculation.
With display showing bni=, press PRINT/ENTER key to show current setting. If setting
displayed is acceptable, press PRINT/ENTER key to save it. Otherwise use numeric keys
0/NO or 1/YES and enter a new setting. Press PRINT/ENTER key to save it.
0 = BMI Disabled
1 = BMI Enabled
P220= (P220 PRINTER)
This setting determines whether weight data sent to the serial port is formatted for a P220
printer or a P185 printer (see CRLF= prompt to select P185 printing mode).
With display showing P220=, press PRINT/ENTER key to show current setting. If setting
displayed is acceptable, press PRINT/ENTER key to save it. Otherwise, using numeric keys
0/NO or 1/YES, enter a new setting, then press PRINT/ENTER key to save it.
0 = NO (Weight Data is Formatted for
P185 printer)
1 = YES (Weight Data is Formatted for
P220 printer)
IMPORTANT! If you select P220=1 (Weight Data is Formatted for P220 printer), the
display will skip to the baUd= prompt.
CrLF= (P185 PRINTER MODE)
This setting determines whether weight data sent to the serial port is formatted for a P185
printer in Journal mode or a P185 printer in Ticket mode. NOTE: If you select CRLF= 1,
(Ticket Mode), an additional prompt (EOP=) will be displayed.
With display showing CRLF=, press the PRINT/ENTER key to show current setting. If setting
displayed is acceptable, press PRINT/ENTER key to save it. Otherwise use numeric keys
0/NO or 1/YES and enter a new setting. Press PRINT/ENTER key to save it.
0 = Set Serial Format for P185 Printer
in Journal Mode
1 = Set Serial Format for P185 Printer
in Ticket Mode
IMPORTANT! The EOP= END OF PRINT LINEFEEDS prompt will only be displayed if
you select P220=0 and CRLF=1.
26
8555-M433-O1 Rev J y 758CSV Owner’s
SETUP AND CALIBRATION, CONT.
EOP= (END OF PRINT LINEFEEDS)
At the end of data sent to a printer, the indicator can send a number of line feed commands
to space the paper in the printer to a desired position for withdrawal or for the next print.
With display showing EOP=, press PRINT/ENTER key to show current setting. If value
displayed is acceptable, press PRINT/ENTER key to save it. Otherwise using numeric keys,
enter a new value and then press PRINT/ENTER key to save it. Allowable values are: 00
through 99.
BAUD= (SERIAL OUTPUT BAUD RATE)
With display showing baUd=, press PRINT/ENTER key to show current setting. If value
displayed is acceptable, press PRINT/ENTER key to save it. Otherwise using numeric keys,
enter a new value and then press PRINT/ENTER key to save it.
0 = 1200 Baud
3 = 9600 Baud
1 = 2400 Baud
4 = 19.2k Baud
2 = 4800 Baud
5 = 38.4k Baud
PPORT (PRINTER OR DATA PORT)
With display showing PPORT, press PRINT/ENTER key to show current setting. If value
displayed is acceptable, press PRINT/ENTER key to save it. Otherwise using numeric keys,
enter a new value and then press PRINT/ENTER key to save it.
1 = Serial Port
2 = Ethernet (requires 758-IP option)
3 = USB Device Port
Cont1 (CONTINUOUS OUTPUT SERIAL PORT)
With display showing COnt1, press PRINT/ENTER key to show current setting. If setting
displayed is acceptable, press PRINT/ENTER key to save it. Otherwise use numeric keys
0/NO or 1/YES and enter a new setting. Press PRINT/ENTER key to save it.
0 = Serial Port Continuous
Output is Disabled
1 = Serial Port Continuous
Output is Enabled
COnt2 (CONTINOUS OUTPUT ETHERNET PORT)
With display showing COnt2, press PRINT/ENTER key to show current setting. If setting
displayed is acceptable, press PRINT/ENTER key to save it. Otherwise use numeric keys
0/NO or 1/YES and enter a new setting. Press PRINT/ENTER key to save it.
0 = Ethernet Port Continuous
Output is Disabled
1 = Ethernet Port Continuous
Output is Enabled
COnt3 (CONTINOUS OUTPUT USB DEVICE PORT)
With display showing COnt3, press PRINT/ENTER key to show current setting. If setting
displayed is acceptable, press PRINT/ENTER key to save it. Otherwise use numeric keys
0/NO or 1/YES and enter a new setting. Press PRINT/ENTER key to save it.
0 = USB Device Port Continuous
Output is Disabled
1 = USB Device Port Continuous
Output is Enable
8555-M433-O1 Rev J y 758CSV Owner’s
27
SETUP AND CALIBRATION, CONT.
btn= (BUTTON OPERATION)
This setting determines which keys (NET/GROSS, TARE, and/or ID/HEIGHT) are locked out
during normal operation.
Press PRINT/ENTER key to show current setting. If value displayed is acceptable, press
PRINT/ENTER key to save it. Otherwise using numeric keys, enter a new value and then
press PRINT/ENTER key to save it.
0 = No Keys Disabled
2 = ID/HEIGHT Keys Disabled
1 = NET/GROSS and TARE Keys
Disabled
3 = NET/GROSS, TARE, and
ID/HEIGHT Keys Disabled
niCAd (BATTERY OPERATION)
This setting is configured at the factory and should not be changed.
With display showing niCAd=, press PRINT/ENTER key to show current setting. This
setting must be set as 1. If any other value is displayed, press 1/YES and then press
PRINT/ENTER key to save it.
0 = Invalid Selection
1 = NiCad or NiMH
PUO= (POWER UP ZERO)
With display showing PUO=, press PRINT/ENTER key to show current setting. If setting
displayed is acceptable, press PRINT/ENTER key to save it. Otherwise use numeric keys
0/NO or 1/YES and enter a new setting. Press PRINT/ENTER key to save it and proceed to
the next prompt.
0 = NO (Weight display will not be
reset to zero)
1 = YES (Weight display will be reset
to zero automatically on power up)
ASH= (AUTOMATIC SHUTOFF)
The Automatic Shutoff feature will turn the indicator off after a period of approximately 1 to 9
minutes of inactivity to prolong battery life. You must press ON/OFF key to turn indicator
back on.
With display showing ASH=, press PRINT/ENTER key to show current setting. If setting
displayed is acceptable, press PRINT/ENTER key to save it. Otherwise use numeric keys to
enter a new setting and then press PRINT/ENTER key to save it. Allowable values are 0
through 9 with 0 disabling Automatic Shutoff.
SLP= (SLEEP MODE)
The Sleep Mode feature also conserves battery power when the indicator remains unused for
a period of approximately 1 to 9 minutes. When enabled, the load cell excitation will be
reduced and the display will show SLEEP. The Sleep feature requires the indicator to remain
at the center of zero to activate, unlike Automatic Shutoff feature which only requires no
motion. Weight placed on scale will activate indicator and return it to weight mode.
With display showing SLP=, press PRINT/ENTER key to show current setting. If setting
displayed is acceptable, press PRINT/ENTER key to save it. Otherwise using numeric keys,
enter a new setting and then press PRINT/ENTER key to save it. Allowable values are 0
through 9 with 0 disabling Sleep Mode
28
8555-M433-O1 Rev J y 758CSV Owner’s
SETUP AND CALIBRATION, CONT.
Setup and Calibration Is Complete
The setup and calibration process has been completed. The indicator will reset and then
display weight. Remove power from the indicator, re-install the calibration jumper J2 removed
earlier and re-assemble for use. The indicator is now ready for normal operation.
8555-M433-O1 Rev J y 758CSV Owner’s
29
SETUP REVIEW
The 758CSV indicator allows several operational parameters to be reviewed and changed as
necessary without having to remove the calibration jumper J2 and enter the setup mode.
To Enter Setup Review
1. If indicator is on, press the ON/OFF key.
2. Press and hold the ZERO key and then press the ON/OFF key.
3. The indicator will perform a display test (turn on all digits), show the software version for
a few seconds and then change to show ruie|.
4. Release the ZERO key.
5. The display will change to HirES = (prompt to enable High Resolution Mode feature).
6. Refer to instructions listed in Setup and Calibration section of manual for information on
how to change these parameters.
Parameters in Setup Review will be processed in the following sequence:
¾
x
HirES
Enable High Resolution¾ Mode feature
x
Tra=
Select the number of scale divisions automatically zeroed on power up
x
Allyn= Select whether the indicator is interfaced to a Welch Allyn device
x
Nin=
Set the minutes portion of the time
x
HH=
Set the hours portion of the time
x
Dd=
Set the day of the month
x
Nn=
Set the month of the year
x
Yy=
Set the year
x
iD=
Enable or Disable ID number input feature
x
iDbar= Enable or Disable ID Scanner
x
Htr=
Enable or Disable Digital Height Rod Port
x
Bni=
Enable or Disable BMI calculation feature
x
P220=
Select weight data format for P220 printer or P185 printer
x
CrLF=
Set P185 Printer Mode (P185 Journal Mode or P185 Ticket Mode)
x
EOP=
Set Number of End Of Print linefeeds printed
x
bAUd=
Select baud rate for serial output
x
PPORT
Select Serial or Ethernet or USB Device port for Data Port
x
COnt!
Enable or Disable Serial Port Continuous Output
x
COnt2
Enable or Disable Ethernet Port Continuous Output
x
COnt3
Enable or Disable USB Device Port Continuous Output
x
Btn=
Enable or Disable NET/GROSS, TARE and/or ID/HEIGHT keys
x
niCAd
Select to use Ni-Cad (NiMH) or Alkaline batteries
x
PUO=
Enable or Disable automatic reset of weight display to zero on power up
x
ASH=
Disable or select number of minutes for automatic shutoff timer
x
SLP=
Disable or select number of minutes of inactivity at zero for sleep mode
NOTE: If HirES= 1 (YES) is selected, the indicator will exit Setup Review and display
weight in High Resolution Weight mode. To return to Setup Review, repeat steps 1 to 4
above.
30
8555-M433-O1 Rev J y 758CSV Owner’s
PRINTER TICKET FORMATS
P220 Ticket
If the P220 Ticket printer was selected, P220=1 (1 = Enable P220 Serial Format) during
setup and calibration of the indicator, the data will be transmitted in the following format:
Time, dd/mm/yy
ID:
BMI:
Height:
Weight:
xxxxxxxxxxx
xx.x
xx.x cm
xxx.xuu G
xxx.xuu PT
xxx.xuu N
NOTE: When the P220 printer is enabled, every time the indicator is powered on, it will print a
test ticket making sure the P220 printer is in the correct mode of operation.
If the printer is in the correct mode the ticket will look like:
OEPL1
Cardinal Scale Mfg
Test Label
If the printer is not in the correct mode, the ticket will look like:
Cardinal Scale Mfg
Test Label
IMPORTANT! After printing the test ticket, the printer will switch to the correct mode.
P185 Journal Mode
If the P220 Ticket printer was not selected, P220=0 (0 = Weight Data Formatted for P185
printer) AND CRLF=0 (0 = Set Serial Format for P185 in Journal Mode) during setup and
calibration of the indicator, the data will be transmitted in the following format:
Weight, BMI, Height, Time, Date
P185 Ticket Mode
If the P220 Ticket printer was not selected, P220=0 (0 = 0 = Weight Data Formatted for P185
printer) AND CRLF=1 (1 = Set Serial Format for P185 Printer in Ticket Mode) during setup
and calibration of the indicator, the data will be transmitted in the following format:
Time, dd/mm/yy
ID:
BMI:
Height:
Weight:
xxxxxxxxxxx
xx.x
xx.x cm
xxx.xuu G
xxx.xuu PT
xxx.xuu N
NOTE: The P185 printer (both modes) doesn’t print a test ticket on power-up.
IMPORTANT! If ID or BMI are disabled, the field will be left out on any three formats.
8555-M433-O1 Rev J y 758CSV Owner’s
31
WEIGHT ON DEMAND FORMATS
Weight On Demand
If the continuous output was not selected for the serial port, Cont1=0, the USB Device port,
Cont2=0 or the optional Ethernet port, Cont3=0 and the indicator is connected to a
computer for transmission of weight data to a PC-based EMR (electronic medical record)
software program, it will transmit a single set of weight data each time the computer sends an
weight request “ENQ” (hex 05) or a SMA weight request “W”. This is known as Weight-OnDemand. Examples and explanation of the data format transmitted are shown below.
The host device (computer) sends:
ENQ (hex 05)
The 758CSV will respond:
<s><xxxxxx><d><uu><m><cc><cr>
Where:
s=
xxxxxx.xxx =
d=
uu =
m=
cc =
Sign
Weight
Decimal point
Units
Mode
Weight Status
cr =
Carriage Return
"-" = negative, " " (blank) = positive
Six digits
Added to string if enabled in setup
kg
G = Gross, N = Net
OC = overcap
CZ = center of zero
MO = motion
ee = weight not currently being displayed
(hex 0D)
SMA Standard Format
The host device (computer) sends:
<lf> W <cr>
The 758C will respond:
<lf>W01,<s><r><n><m><f><xxxxxx.xxx><uuu><cr>
Where:
32
lf =
W01
,
s=
Line Feed
W01
Comma
Flags
r=
n=
M=
f=
xxxxxx.xxx =
uuu =
cr =
Range
Mode
Motion
Custom
Weight
Units
Carriage Return
The text “W01”
(hex 2C)
Z= center of Zero, O = Overcap, E = zero Error,
e = weight not currently being displayed
1, 2, 3, ...
G = Gross, T = Tare, N = Net
M = Motion, " "(blank) = no motion
Custom flag
Six digits with decimal point
None, lb, kg, oz, g, st
(hex 0D)
8555-M433-O1 Rev J y 758CSV Owner’s
SERIAL AND USB DEVICE PORT COMMANDS
The following commands and formats apply to both the Serial port and the USB Device port.
Both the Serial port and USB Device port on the 758CSV are bi-directional ports and can
receive and transmit data. However, the USB Device port can only communicate with a
computer. The Serial port can output to a printer as well as communicate to a computer.
Serial Port
Using the serial port, it is possible to control the printing operation of the 758CSV by
transmitting commands to the indicator. Note that the PPORT parameter in the indicator
must be set to 1 = Serial Port to allow this.
USB Device Port
In order for the computer to communicate to the indicator using the USB Device port, the
PPORT parameter on the indicator must be set to 3 = USB Device Port. In addition, the
computer requires a USB driver. Contact your scale service representative for availability.
Remote Print Command
The host device (computer) sends:
<LF> P <CR>
This command is equivalent to pressing the PRINT/ENTER key on the 758CSV keypad. The
758CSV will respond by printing a ticket using the serial port (or transmit data using the USB
Device port). The ticket will be printed (or data transmitted) in the following format:
Time, dd/mm/yy
ID:
BMI:
Height:
Weight:
xxxxxxxxxxx
xx.x
xx.x cm
xxx.xuu G
xxx.xuu PT
xxx.xuu N
Journal Mode Print Command
The host device (computer) sends:
<LF> J <CR>
This command is equivalent to pressing the PRINT/ENTER key on the 758CSV keypad. The
758CSV will respond by printing a ticket using the serial port (or transmit data using the USB
Device port). The ticket will be printed (or data transmitted) in the following format:
Weight, BMI, Height, Time, Date
NOTE: This command is equivalent to pressing the PRINT/ENTER key on the 758CSV
keypad with the P220 Serial Format Disabled and CRLF Enabled (P220=0), and the
CRLF set for Serial Format for P185 Journal Mode (Crlf=0) parameters selected. Note
that this command will print a ticket (or transmit data) in the above format regardless of
how the P220= and CrLF= parameters are set.
IMPORTANT! If ID or BMI are disabled, the field will be left out on any three formats.
8555-M433-O1 Rev J y 758CSV Owner’s
33
SERIAL AND USB DEVICE PORT COMMANDS, CONT.
Data Queue Commands
The 758CSV has been equipped with storage for weight records. When taking a weight
record, once the PRINT/ENTER key is pressed, the weight, ID (if enabled and entered), date
and time are stored in the indicator. The indicator can store up to 250 weight records. Once
the limit is reached, the oldest record will be over written to make room for the new weight
record.
Delete Data Queue Command
The host device (computer) sends:
<LF> XD <CR>
The 758CSV will Delete the Data Queue.
Recall Data Queue Command
The host device (computer) sends:
<LF> XS <CR>
The 758CSV will Recall the Data Queue. The ticket will be printed (or data transmitted) in the
following format:
ID, Date, Time, Weight, Units, Mode<cr><lf>
Where:
ID =
Date =
Time =
Weight =
Units =
m=
cr =
lf =
xxxxxxxxxxx
dd/mm/yy
hh:mm
xxxxxx.x
uu
Mode
Carriage Return
Line Feed
Up to 11 digit ID number
Day, Month, Year
Hours and Minutes
Six digits with decimal point
kg
G = Gross
(hex 0D)
(hex 0A)
NOTE: Recalling the data queue does not delete the current data. The separate delete
command must be sent to clear the queue.
34
8555-M433-O1 Rev J y 758CSV Owner’s
ERROR AND STATUS DISPLAYS
Display
-Err-OF-
Meaning
General error, invalid keypad entry was attempted.
Attempting to display a negative number greater than –9,999 or a
positive number greater than 99,999
-trL-
Indicates an attempt to zero a weight outside scale zero range. Refer to
the Setup and Calibration trL= (Four Percent Zero Tracking Range
Limit) parameter.
-UnS-
Motion is present when indicator is attempting to perform one of the
following operations: Power Up, Zero, or Zero Weight Display
CALib
CERR
Indicates calibration is necessary.
AdErr
ErrA
ErrAL
ErrAH
EE Err
OCAP
Attempting to enter Setup and Calibration with the calibration jumper
(J2) installed.
Consult your scale service representative.
Scale weight exceeds scale capacity
BEFORE YOU CALL FOR SERVICE
Problem
Display does not
turn on
Possible Solutions
AC Operation:
x Is AC power supply fully inserted into wall receptacle?
x Check wall receptacle for proper AC power. Try another electrical
appliance in same receptacle, does it work?
x Check circuit breaker.
x Has there been power failure?
Battery operation:
x Check if batteries are installed and correctly.
x Are batteries discharged?
Connect the optional 12 VDC AC power adapter's connector
into the jack on the back of the indicator and then plug the
power adapter into the proper electrical outlet to operate the
indicator and recharge the batteries.
Otherwise, remove discharged batteries and replace with fully
charged ones and place discharged batteries in an external
charger to recharge.
Incorrect weight
displayed
Insure that scale platform isn't touching an adjacent object.
Have proper operation procedures been followed?
Indicator will not
display weight
Refer to Error and Status Display section and make certain that the
O CAP message is not displayed. If so, and scale is not loaded,
perform the calibration sequence.
The digital height rod was not in its “starting position” prior to turning
on the indicator. Push inner sliding tube completely down inside
outer stationary tube and fold headpiece against stationary tube.
Indicator displays
999.9 for height
8555-M433-O1 Rev J y 758CSV Owner’s
35
EVENT COUNTER
The 758CSV weight indicator has been designed with an Event Counter type of security seal.
When selected, the 758CSV will display two 3-digit numbers representing the Calibration and
Configuration counters.
Calibration Counter
The calibration counter is incremented when a value in the calibration part of setup is
changed (SetGC, CALGC, OPGC, int, Unit, trA, UnS, dPP, CAP, FLt, F, br, Sr, CAL,).
The counter is only incremented 1 time even if more than one parameter is changed each
time through setup.
Configuration Counter
The configuration counter is incremented when a value in the configuration part of setup is
changed (Hold, bAnd, PUO, niCAd, SLEEP, ASH). The counter is only incremented 1
time even if more than one parameter is changed each time through setup.
To Review the Event Counter:
1. If indicator is on, press the ON/OFF key.
2. Press and hold the UNITS key and then press the ON/OFF key.
3. The indicator will perform a display test (turn on all digits), show the software version for
a few seconds and then change to show CAL1 and CHC.
4. Release the UNITS key.
5. The display will then show two 3-digit numbers.
x The left number represents the setup Calibration counter.
x The right number represents the Configuration counter.
6. To return to the normal operation, press the UNITS key.
7. Otherwise press the ON/OFF key to turn off the indicator.
CARE AND CLEANING
36
ƒ
DO NOT submerge indicator in water, pour or spray water directly on indicator.
ƒ
DO NOT use acetone, thinner or other volatile solvents for cleaning.
ƒ
DO NOT expose equipment to temperature extremes.
ƒ
DO NOT place equipment in front of heating/cooling vents.
ƒ
DO clean the indicator with a damp soft cloth and mild non-abrasive detergent.
ƒ
DO remove power before cleaning with a damp cloth.
ƒ
ƒ
DO provide clean AC power and adequate protection against lightning damage.
DO keep the surroundings clear to provide clean and adequate air circulation.
8555-M433-O1 Rev J y 758CSV Owner’s
SECURITY SEAL INSTALLATION
The 758CSV weight indicating instrument is designed for attachment of a lead-wire security
seal which prevents the scale cable from being disconnected from the weight indicator (see
Figure No 10). Local metrology laws may or may not require this security seal. If your
metrology laws require a security seal, follow the directions provided below to install the seal.
Load Cell Cable Connection
1. Make certain the load cell cable is securely tightened to the 9-pin “D” connector on the
rear of the indicator before proceeding.
2. Thread the sealing wire through the hole in the connector and the drilled fillister head
screw near the load cell connector on the rear of the indicator as shown in Figure 10.
3. Pull the wire tight and install the lead seal.
Figure No. 10
8555-M433-O1 Rev J y 758CSV Owner’s
37
This page intentionally left blank.
38
8555-M433-O1 Rev J y 758CSV Owner’s
PARTS IDENTIFICATION
Rear View Detail
ITEM QTY. PART NUMBER
DESCRIPTION
1
1
593GR986
SERIAL TAG ASSEMBLY
3
1
6021-2071
SCW FILLISTER 6-32 X 0.25 DRILLED
4
1
6021-1032
THUMB SCRW, 6-32 X 0.25
5
4
6021-2069
SCW TRUSS HEAD SHEET METAL #6 X .50 (WHITE)
6
4
6021-6008
SCW TRUSS HEAD SHEET-METAL #6 X.375” (BLACK)
8
4
6610-2000
JACK SOCKET
12
9
6680-0004
WASHER LOCK INT. TOOTH #6 Z/P
13
4
6680-0052
WASHER LOCK HELICAL #4 Z/P
17
1
8555-B434-08
LABEL: USE ONLY RECHARGE...C...BATTERIES
18
1
8555-B166-18
BATTERY COVER
19
1
8555-B452-08
BOX, THREE CONNECTOR
20
1
8555-B453-08
BOX, TWO CONNECTOR
22
2
8555-C213-08
END CAP
23
1
8555-C448-0A
REAR PANEL ASSEMBLY
27
1
8555-C216-0A
BATTERY CHARGER PCB ASSY
28
1
6560-0005
TAPE DBL-SIDED 1” WIDE X 10MIL – CUT 2” LONG
Optional AC Adapters (not shown)
6800-1045
AC ADAPTER 100-240VAC/12VDC @ 1 AMP US PLUG
6800-1047
AC ADAPTER 100-240VAC/12VDC @ 1 AMP EURO PLUG
AC230AU
AC ADAPTER 100-240VAC/12VDC @ 1 AMP, AU PLUG
AC230UK
AC ADAPTER 100-240VAC/12VDC @ 1 AMP, UK PLUG
8555-M433-O1 Rev J y 758CSV Owner’s
39
PARTS IDENTIFICATION, CONT.
Inside Rear View Detail
ITEM QTY.
40
PART NUMBER
DESCRIPTION
2
4
6013-0039
NUT HEX #6-32
7
2
6024-0126
WASHER FLAT FOR 5/32” POP RIVET
9
1
6610-5119
BATTERY HOLDER 6-C CELLS
12
9
6680-0004
WASHER LOCK INT. TOOTH #6 Z/P
14
4
6680-0138
SPACER #6 X .187 NYLON
15
2
6680-0214
POP RIVET BH AL 5/32 DIA
16
1
8200-B369-08
GROUND SPRING
21
1
8555-B219-0A
CABLE: BATTERY
24
1
8555-C450-0A
FRONT PANEL WELDMENT
26
1
8555-D444-0A
BOARD ASSEMBLY – 758C
29
1
8555-C221-0A
CABLE: POWER CORD
8555-M433-O1 Rev J y 758CSV Owner’s
PARTS IDENTIFICATION, CONT.
Battery Cover Detail
ITEM QTY.
Side View Detail
PART NUMBER
DESCRIPTION
1
1
593GR986
SERIAL TAG ASSEMBLY
2
4
6013-0039
NUT HEX #6-32
3
2
6021-0687
SCW TRUSS HEAD #6-32 X .375 THMS
4
1
6021-1032
THUMB SCRW, 6-32 X 0.25
5
4
6021-2069
SCW TRUSS HEAD SHEET METAL #6 X .50 (WHITE)
9
1
6610-5119
BATTERY HOLDER 6-C CELLS
10
1
6650-0018
GASKET MATERIAL 1” X 1/2” X 5 1/4”
12
9
6680-0004
WASHER LOCK INT. TOOTH #6 Z/P
14
4
6680-0138
SPACER #6 X .187 NYLON
16
1
8200-B369-08
GROUND SPRING
17
2
8555-B159-08
SPACER, 758C MOUNT
18
1
8555-B166-08
BATTERY COVER
19
1
8555-B452-08
BOX, THREE CONNECTOR
21
1
8555-B219-0A
CABLE: BATTERY
25
1
8555-D222-08
KEYPAD: 758CSV (INTERNATIONAL VERSION)
26
1
8555-D444-0A
BOARD ASEMBLY – 758C
27
1
8555-C216-0A
BATTERY CHARGER PCB ASSY
29
1
8555-C221-0A
CABLE: POWER CORD
30
1
8555-B469-0A
CABLE: POWER
8555-M433-O1 Rev J y 758CSV Owner’s
41
STATEMENT OF LIMITED WARRANTY
Detecto Scale warrants its equipment to be free from defects in
material and workmanship as follows: Detecto warrants to the
original purchaser only that it will repair or replace any part of
equipment which is defective in material or workmanship for a
period of one (1) year from date of shipment. Detecto shall be the
sole judge of what constitutes a defect.
During the first ninety (90) days Detecto may choose to supply all
necessary replacement parts and service during normal weekday
working hours at no charge to the buyer.
After the first ninety (90) days Detecto will supply parts and
service at the job site provided the owner agrees to pay the Dealer
for all travel time, including mileage and test equipment, as well as
any expenses incurred over the direct labor of the technician at the
job site. This limited warranty honors only labor performed by
Detecto authorized dealers.
This warranty does not apply to peripheral equipment not
manufactured by Detecto; this equipment will be covered by certain
manufacturer’s warranty only.
This warranty does not include replacement of expendable or
consumable parts. This does not apply to any item which has
deteriorated or damaged due to wear, accident, misuse, abuse,
improper line voltage, overloading, theft, lightning, fire, water or acts
of God, or due to extended storage or exposure while in purchaser’s
possession. This warranty does not apply to maintenance service.
Purchased parts will have a ninety (90) day repair or replacement
warranty only.
Detecto may require components be returned to the factory; they
must be properly packed and shipping charges prepaid. A return
authorization number must be obtained for all returns and marked
on the outside of all returned packages. Detecto accepts no
responsibility for loss or damage in transit.
42
8555-M433-O1 Rev J y 758CSV Owner’s
STATEMENT OF LIMITED WARRANTY
Conditions Which Void Limited Warranty
This warranty shall not apply to equipment which:
A.) Has been tampered with, defaced, mishandled or have had
repairs and modifications not authorized by Detecto.
B.) Has had serial number altered, defaced, or removed.
C.) Has not been grounded according to Detecto’s recommended
procedure.
Freight Carrier Damage
Claims for equipment damaged in transit must be referred to the
freight carrier in accordance with freight carrier regulations.
This warranty sets forth the extent of our liability for breach of any
warranty or deficiency in connection with the sale or use of the
product. Detecto will not be liable for consequential damages of any
nature, including but not limited to, loss of profit, delays or expenses,
whether based on tort or contract. Detecto reserves the right to
incorporate improvements in material and design without notice and
is not obligated to incorporate improvements in equipment
previously manufactured.
The foregoing is in lieu of all other warranties, express or implied
including any warranty that extends beyond the description of the
product including any warranty of merchantability or fitness for a
particular purpose. This warranty covers only those Detecto
products installed in the forty-eight (48) contiguous continental
United States.
Ph. (800) 641-2008
E-mail: detecto@cardet.com
203 E. Daugherty
Webb City, MO 64870
8555-M433-O1 Rev J y 758CSV Owner’s
02/06
Printed in USA
D268-WARRANTY-DET
43
44
8555-M433-O1 Rev J y 758CSV Owner’s
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising