#6460 User's Guide

#6460 User's Guide
Roll-a-Ball Bead Chain Switch #6460
USER’S GUIDE
For Technical Support:
Call our Technical Service Department
Monday through Friday, 9 a.m. to 5 p.m. (EST)
1-800-TEC-TOYS or 1-800-832-8697
customer_support@enablingdevices.com
50 Broadway
Hawthorne, NY 10532
Tel. 914.747.3070 / Fax 914.747.3480
Toll Free 800.832.8697
www.enablingdevices.com
Encourages swiping!
Reach out and give the ball a swipe and feel the shiny beads on your hand while
soothing music plays and bright yellow lights glow. A mirror on the base
reflects your movements. Also has on/off vibration and can operate as a switch.
A fantastic tactile, visual and auditory experience. Size: 14½"L x 8"H x 7"W.
Requires 4 AA Batteries. Weight: 2¼ lbs.
Operation:
1. The Roll-a-Ball Bead Chain Switch requires 4 AA batteries to operate. Use
alkaline batteries only (e.g. Duracell or Energizer brand). Do not use
rechargeable batteries or any other type of batteries because they supply
lower voltage and the unit will not perform properly. Never mix old and
new batteries together or different brands or types together.
2. Carefully turn over unit to reveal battery compartments. Remove the Phillips
Head screws from the battery compartment covers. Next slide the battery
compartment covers off and insert the “AA” batteries into the holders.
Replace the covers and screws.
Clamping Options:
5. The Roll -a-Ball Bead Chain Switch has two locations on the front of the
base for clamping to table tops, or lap trays. Clamps not included. Most CClamps will work.
Please Note: When using the Roll-a-Ball Bead Chain Switch, as a switch after
use remove the switch output cable to prevent battery drain from your connected
device.
Troubleshooting:
Problem: The Roll-a-Ball Bead Chain Switch does not work.
Action #1: Check the batteries for proper installation, as noted in operation No.
2.
Action #2: Check batteries for freshness, if weak or dead replace with new
batteries.
3. Set the ON/OFF/VOLUME switch to the desired VOLUME level. There is
also a Vibration ON/OFF switch. Set the vibration ON or Off As you push
your hand through the draped beads and roll the ball back and forth you will
feel vibration and see lights illuminate as music plays. If you stop moving
the ball the lights, vibration and music will continue to play for
approximately 5 seconds and will then shut off.
Action #4: When using the Roll-a-Ball Bead Chain Switch as a switch, make
sure all connections between the Roll-a-Ball Bead Chain Switch and your device
are plugged in all the way. There should be no gaps.
Using as a Switch:
Action #5: Check your device with another switch to rule out the Roll-a-Ball
Bead Chain Switch out as the source of the problem.
4. To use the Roll-a-Ball Bead Chain Switch as a switch, plug one end of the
included double ended cable into the 1/8" jack on the back of the Roll-a-Ball
Bead Chain Switch and the other end into your switch enabled device. Make
sure both ends are plugged in all the way. There should be no gaps. When
ball is moved back and forth the connected device will activate as long there
is movement of the ball. When the ball stops moving the connected device
will run for the same time duration of the lights, vibration and music
(approximately 5 seconds).
Action #3: Make sure there is nothing obstructing the beads or ball from
moving.
Care of Unit:
The Roll-a-Ball Bead Chain Switch can be wiped clean with any household
multi-purpose cleaner and disinfectant. We recommend Simple Green, which is
a non toxic biodegradable all-purpose cleaner. The ball can be removed for
cleaning.
Do not submerge the unit, as it will damage the contents and the electrical
components.
Do not use abrasive cleaners, as they will scratch the surface of the unit.
Rev 7/20/12
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising