ST60+ Speed

ST60+ Speed
81261_1.book Page i Friday, October 28, 2005 10:02 AM
ST60+ Speed
Instrument
Owner’s Handbook
Document reference: 81261-1
Date: December 2005
81261_1.book Page ii Friday, October 28, 2005 10:02 AM
Raymarine, ST60+ and SeaTalk are trademarks of Raymarine UK Limited
© Handbook contents copyright Raymarine UK Limited 2005
81261_1.book Page i Friday, October 28, 2005 10:02 AM
i
Preface
Contents
Important information
Safety notices
WARNING: Product installation & operation
This equipment must be installed and operated in accordance
with the Raymarine instructions provided. Failure to do so could
result in personal injury, damage to your boat and/or poor
product performance.
WARNING: Electrical safety
Make sure you have switched off the power supply before you
start installing this product.
WARNING: Navigational safety
Although we have designed this product to be accurate and
reliable, many factors can affect its performance. Therefore, it
should serve only as an aid to navigation and should never
replace commonsense and navigational judgement. Always
maintain a permanent watch so you can respond to situations as
they develop.
EMC conformance
All Raymarine equipment and accessories are designed to the best industry
standards for use in the recreational marine environment.
The design and manufacture of Raymarine equipment and accessories conform to
the appropriate Electromagnetic Compatibility (EMC) standards, but correct
installation is required to ensure that performance is not compromised.
Handbook information
To the best of our knowledge, the information in this handbook was correct when
it went to press. However, Raymarine cannot accept liability for any inaccuracies
or omissions it may contain.
In addition, our policy of continuous product improvement may change
specifications without notice. Therefore, Raymarine cannot accept liability for any
differences between the product and the handbook.
81261_1.book Page ii Friday, October 28, 2005 10:02 AM
ii
ST60+ Speed Instrument Owner’s Handbook
Product disposal
Waste Electrical and Electronic (WEEE) Directive
The WEEE Directive requires the recycling of waste electrical and
electronic equipment.
Whilst the WEEE Directive does not apply to some of Raymarine's products, we
support its policy and ask you to be aware of how to dispose of this product.
The crossed out wheelie bin symbol, illustrated above, and found on our products
signifies that this product should not be disposed of in general waste or landfill.
Please contact your local dealer, national distributor or Raymarine Technical
Services for information on product disposal.
81261_1.book Page iii Friday, October 28, 2005 10:02 AM
Preface
iii
Contents
Preface
Preface ................................................................................................................................ i
Important information ............................................................................................ i
Safety notices .................................................................................................... i
WARNING: Product installation & operation.......................................... i
WARNING: Electrical safety .......................................................................... i
WARNING: Navigational safety................................................................... i
EMC conformance ............................................................................................. i
Handbook information ...................................................................................... i
Product disposal ..................................................................................................... ii
Contents........................................................................................................... iii
Introduction ..........................................................................................................vii
Data inputs ............................................................................................................vii
SeaTalk ............................................................................................................vii
Stand alone operation ....................................................................................viii
Remote control ....................................................................................................viii
Mounting options ................................................................................................viii
Parts supplied ........................................................................................................ ix
Chapter 1: Operation ..................................................................................................... 1
1.1 Getting started ................................................................................................. 1
Displayed information ...................................................................................... 1
WARNING: Calibration requirement......................................................... 1
Switching on and off......................................................................................... 1
1.2 Normal operation ............................................................................................. 1
Speed information ............................................................................................ 2
Boat speed ............................................................................................... 2
Maximum speed ...................................................................................... 2
Average speed ......................................................................................... 3
Velocity made good (to windward).......................................................... 3
Speed over ground................................................................................... 3
Log, trip & water temperature .......................................................................... 3
Boat log ................................................................................................... 3
Trip........................................................................................................... 4
Water temperature................................................................................... 4
Timers............................................................................................................... 4
Race-start timers...................................................................................... 5
1.3 Display settings ................................................................................................ 6
Illumination ...................................................................................................... 6
Contrast............................................................................................................ 6
81261_1.book Page iv Friday, October 28, 2005 10:02 AM
iv
ST60+ Speed Instrument Owner’s Handbook
1.4 Pop-up Pilot ......................................................................................................6
1.5 Remote control .................................................................................................6
Chapter 2: Maintenance & Troubleshooting ...........................................................7
2.1 Maintenance ....................................................................................................7
Servicing and safety ..........................................................................................7
Instrument ........................................................................................................7
Transducer.........................................................................................................7
Cabling..............................................................................................................8
2.2 Troubleshooting ...............................................................................................8
Preliminary procedures .....................................................................................8
Fixing faults.......................................................................................................8
CAUTION: Prevention of flooding ..............................................................8
Technical support ..............................................................................................9
World wide web....................................................................................... 9
Telephone help line.................................................................................. 9
Help us to help you .................................................................................. 9
Chapter 3: Installation ................................................................................................11
3.1 Planning your installation ...............................................................................11
Site requirements............................................................................................11
Transducer ............................................................................................. 11
Instrument.............................................................................................. 13
CAUTION: Keep the rear of the instrument dry..................................13
EMC installation guidelines.............................................................................14
Suppression ferrites................................................................................ 14
Connections to other equipment............................................................ 15
3.2 Procedures .....................................................................................................15
CAUTION: Maintain structural safety .....................................................15
Unpacking.......................................................................................................15
Fitting the instrument......................................................................................15
Surface mounting................................................................................... 16
Flush mounting ...................................................................................... 17
CAUTION: Use the correct screws.............................................................17
Bracket mounting................................................................................... 19
Fitting transducer ............................................................................................20
Running transducer cable....................................................................... 20
Connecting the instrument .............................................................................21
Types of connection ............................................................................... 21
Signal connections ................................................................................. 21
Power supply connections...................................................................... 22
81261_1.book Page v Friday, October 28, 2005 10:02 AM
Preface
v
CAUTION: Protect the power supply ...................................................... 22
3.3 Switching on .................................................................................................. 23
WARNING: Calibration requirement....................................................... 23
EMC conformance .......................................................................................... 23
Chapter 4: Calibration ................................................................................................. 25
4.1 Introduction ................................................................................................... 25
4.2 User calibration .............................................................................................. 25
Set speed units....................................................................................... 25
Set resolution......................................................................................... 26
Set log units ........................................................................................... 26
Setting the correct speed ....................................................................... 26
Set temperature units............................................................................. 28
Temperature calibration......................................................................... 28
Timer buzzer .......................................................................................... 28
Pop-up pilot ........................................................................................... 28
Leaving User calibration......................................................................... 28
4.3 Intermediate calibration ................................................................................ 28
Speed calibration............................................................................................ 29
Leaving Intermediate calibration.................................................................... 32
4.4 Dealer calibration ........................................................................................... 32
User calibration on/off .................................................................................... 32
Response settings........................................................................................... 33
Boat show mode............................................................................................. 34
CAUTION: Do NOT enable Boat Show Mode ........................................ 34
Factory defaults .............................................................................................. 34
Leaving Dealer calibration .............................................................................. 34
Glossary ........................................................................................................................... 35
Index ................................................................................................................................. 37
81261_1.book Page vi Friday, October 28, 2005 10:02 AM
vi
ST60+ Speed Instrument Owner’s Handbook
81261_1.book Page vii Friday, October 28, 2005 10:02 AM
Preface
vii
Introduction
Preface
Thank you for purchasing a Raymarine product. We are sure your ST60+
instrument will give you many years of trouble-free operation.
This handbook describes how to install and use the Raymarine ST60+ Speed
instrument. This instrument provides accurate speed, log, trip and timer
information, on a high quality Liquid Crystal Display (LCD). The instrument is
constructed in a rugged weather-proofed case to provide reliable performance,
even under the most demanding conditions.
ST
6
0+
SP
EE
D
SPE
ED
TR
IP
TIM
ER
RE
SET
1
38-
D81
Data inputs
The ST60+ Speed instrument receives data either from an appropriate speed
transducer and/or from a SeaTalk instrumentation system.
SeaTalk
SeaTalk enables a number of compatible instruments to operate as a single,
integrated navigational system. Instruments in a SeaTalk system are linked by
means of a single cable, which feeds both power and data. Instruments can
therefore be added to the system by plugging them into the network. SeaTalk is
flexible enough to adapt to any number of compatible instruments without
requiring a central processor. SeaTalk can also communicate via an interface, with
non-SeaTalk equipment using the internationally-accepted National Marine
Electronics Association (NMEA) protocol.
In a SeaTalk system, each instrument can be either a master or dedicated repeater
unit. A master instrument is directly connected to a transducer (the device that
provides the raw data), and provides data and control appropriate to its function,
81261_1.book Page viii Friday, October 28, 2005 10:02 AM
viii
ST60+ Speed Instrument Owner’s Handbook
to all other equipment on the SeaTalk network. A repeater instrument is not
directly connected to a transducer but displays information provided by other
equipment in the SeaTalk network.
The ST60+ Speed instrument can fulfil both master and repeater roles.
Stand alone operation
In Stand alone operation, the ST60+ Speed instrument is connected only to the
relevant transducer and does not display information from, or provide
information to, any other instruments.
Remote control
When connected to SeaTalk, the ST60+ Speed instrument can be controlled
remotely by a SeaTalk Remote Keypad Unit, to provide instant remote access to
the various display readouts.
Mounting options
A standard ST60+ instrument is surface-mounted at the required location. If you
do not want to surface mount your ST60+ instrument, options are available for:
• Flush mounting. If you have ordered the flush mounting option a flush mount
bezel and four fixing screws are provided.
• Bracket mounting.
81261_1.book Page ix Friday, October 28, 2005 10:02 AM
Preface
ix
Parts supplied
Unpack your ST60+ instrument and check that the following items are present:
• Item 1, ST60+ Speed instrument fitted with standard bezel for surface
mounting.
• Item 2, Fixing studs (2).
• Item 3, Thumb nuts (2).
• Item 4, Gasket.
• Item 5, Speed transducer, plus bung (not illustrated).
• Item 6, SeaTalk interconnection cable.
• Item 7, Power cable.
• Item 8, Instrument Cover.
• Item 9, Owner’s Handbook. A Warranty document and fitting
templates are included in this Handbook.
• Item 10, Quick Start Guide.
Spare spade terminals are also provided, to re-terminate the transducer cable if it
has to be cut to facilitate installation.
Note: The above packing list is for an ST60+ Speed system. Where an instrument is purchased separately, a transducer is not included.
81261_1.book Page x Friday, October 28, 2005 10:02 AM
x
ST60+ Speed Instrument Owner’s Handbook
TIMER
TRIP
3
2
3
RESET
1
8
4
5
7
6
ST60+
Speed
Instrument
Owner's
Handbook
ST60+ Speed
Instrument
Quick Start Guide
9
10
D8140-1
SPEED
2
81261_1.book Page 1 Friday, October 28, 2005 10:02 AM
1
Chapter 1: Operation
1.1 Getting started
Displayed information
Your ST60+ Speed instrument provides the following:
• Speed information.
• Log, trip and water temperature information.
• Count-up and race-start timers.
WARNING: Calibration requirement
To ensure this product performs at its best on your boat, you
MUST calibrate it before use, in accordance with the instructions
in Chapter 4, Calibration. Do NOT use the product until you have
successfully calibrated it.
Switching on and off
All the time that power is applied to the instrument, you can use the speed
button to switch the instrument off and on as follows:
• To switch the instrument off, hold down the speed button for approximately
5 seconds. After this time, a switch off count down of 4 seconds occurs. Keep
the speed button pressed during this period, to switch off the instrument.
• To switch the instrument back on, hold down the speed button for approximately 1 second.
When the power supply is switched off, none of the instrument buttons (including
speed) has any effect.
Notes: (1) Each time power to the instrument is switched on, the instrument is ini-
tially in the on condition. You do not need to use the speed button to
switch the instrument on.
(2) When the instrument is on, the operation of the speed button will
perform other operating functions, as described below.
1.2 Normal operation
Use the flow charts in this Chapter to operate your ST60+ Speed instrument. The
flow charts show the sequence of button presses and displays for the various
operating tasks. All button presses are momentary unless otherwise stated.
81261_1.book Page 2 Friday, October 28, 2005 10:02 AM
2
ST60+ Speed Instrument Owner’s Handbook
Speed information
When power is switched on, the speed button gives you access to current speed,
maximum speed, average speed, velocity made good (VMG) and speed over
ground (SOG) information. Refer to the Speed information flow diagram to
access the information you want.
Boat speed
The boat speed reading shows the current speed of the boat through the water.
Speed measurement units are either knots (KTS), miles per hour (MPH) or
kilometers per hour (KMH). You can select the units you want during user
calibration (see Chapter 4, Calibration ).
speed
Boat
speed
speed
speed
Maximum
speed
Speed over
ground
reset
3s
Resets to current
boat speed
7 second timeout
speed
speed
Average
speed
Velocity made
good
reset
Resets to zero
3s
7 second timeout
Speed information
D8139-1
speed
Maximum speed
The maximum speed reading is reset at power up. You can also reset it manually,
by pressing the reset button for 3 seconds. The display shows the maximum
81261_1.book Page 3 Friday, October 28, 2005 10:02 AM
Chapter 1: Operation
3
recorded speed since the last reset. This screen times-out to current speed if no
user action occurs for 7 seconds.
Average speed
The average speed reading is reset at power up. You can also reset it manually by
pressing the reset button for 3 seconds. The display shows the average speed
calculated since the last reset. This screen times-out to current speed if no user
action occurs for 7 seconds.
Velocity made good (to windward)
Velocity made good (VMG) information is available if your ST60+ Speed
instrument is part of a SeaTalk system to which a SeaTalk-compatible wind
instrument is also connected.
Speed over ground
Speed over ground (SOG) information is available if your ST60+ Speed
instrument is part of a SeaTalk system to which a suitable GPS is also connected.
Log, trip & water temperature
The trip button gives you access to log, trip and water temperature information,
as shown in the Distance & water temperature flow diagram.
trip
trip
trip
Water
temperature
Trip
distance
Boat log
reset
Resets to zero
3s
Distance & water temperature information
Boat log
The boat log screen shows the total distance covered by the vessel since the
ST60+ Speed instrument was fitted.
D8141-1
trip
81261_1.book Page 4 Friday, October 28, 2005 10:02 AM
4
ST60+ Speed Instrument Owner’s Handbook
Trip
The trip distance is the distance covered since the last reset. It is reset to zero at
power up, and if you press the reset button for 3 seconds.
Note: The trip distance can be reset only if the instrument is a master, i.e. connected to a
speed transducer.
Water temperature
The water temperature is shown in either degrees Celsius or Fahrenheit. You can
set the units you want during User calibration (see Chapter 4, Calibration ).
Timers
The timer button gives access to a count-up timer and to two race-start timers.
Times are either in seconds (S) or minutes (M), depending on the counter values.
Refer to the Selecting timer flow diagram to display the required timer.
timer
timer
timer
Count-up timer
Race-start
timer 2
Race-start
timer 1
timer
When timer running reset gets lap time
Selecting timer
D8142-1
When timer stopped reset starts timer
Once you have selected the required timer display, press the reset button to start
the timer running. When a timer is running, the delimiter ( . or : ) flashes. For lap
timing, press the reset button. To stop and reset a timer to the start value, hold
down the reset button for 1 second.
Once a timer is running, you can leave the timer screen and select any other
display. The timer will continue to run in the background.
81261_1.book Page 5 Friday, October 28, 2005 10:02 AM
Chapter 1: Operation
5
Race-start timers
You can set each race-start timer to any whole-minute value from 1 to 15 minutes.
Note: When the instrument is first installed, the race-start timers are set to 4 and 5 minutes respectively.
To set a race-start timer:
1. Use the timer button as shown in the Selecting timer flow diagram, to select
the required race-start timer.
2. Simultaneously press the timer and reset buttons to enter the race-start
timer set mode.
3. Use either the timer or reset button to set the required value.
4. Simultaneously press the timer and reset buttons to save the value and
leave the race-start timer adjust mode.
Increase time
reset
Set
screen
+
reset
OR
timer
reset
+
timer
Decrease time
Set race-start timer
D8143-1
timer
Timer buzzer
The timer buzzer is enabled or disabled during User calibration procedure (see
Chapter 4, Calibration ). If the timer buzzer is enabled and you are using one of the
race-start timers, the buzzer will:
• Double-beep every minute.
• Beep three times at the start of the last 30 seconds.
• Beep once for each of the last 10 seconds.
• Beep for 2 seconds at zero.
Note: After a race-start timer has counted-down to zero, it will then start counting up.
81261_1.book Page 6 Friday, October 28, 2005 10:02 AM
6
ST60+ Speed Instrument Owner’s Handbook
1.3 Display settings
Illumination
When the instrument is first powered up, the display illumination is set to its lowest
level, to facilitate initial access to the buttons. To adjust the illumination level:
1. Hold down the speed button for approximately one second, to enter the illumination-adjust mode.
2. There are four preset illumination levels. Press the speed button to cycle
through these levels until you reach the level you want.
3. Press any other button to leave the illumination-adjust mode.
Note: The display will time out to normal operation 7 seconds after the last button press.
Contrast
To adjust the display contrast:
1. Hold down the speed button for approximately two seconds, to enter the
contrast-adjust mode.
i. There are four preset contrast settings. Press the speed button to cycle
through these settings until you achieve optimum display quality.
i. Press any other button to leave the contrast-adjust mode.
Note: The display will time out to normal operation 7 seconds after the last button press.
1.4 Pop-up Pilot
A Pop-up Pilot facility enables instruments connected to SeaTalk to constantly
monitor any changes to the autopilot mode and to the course settings. If one of
these parameters changes, the new value is immediately displayed on the ST60+
instrument for 5 seconds, after which time the display reverts to the previous
display.
This facility can be enabled or disabled during User calibration (see Chapter 4,
Calibration ).
1.5 Remote control
When connected to SeaTalk, the ST60+ Speed instrument can be controlled
remotely with a SeaTalk Remote Keypad Unit. Remote control of an instrument is
indicated by a REMOTE legend on the display, to indicate that the keypad has
control.
Details on how to use the remote control facility are given in the SeaTalk Remote
Keypad Owner’s Handbook.
81261_1.book Page 7 Friday, October 28, 2005 10:02 AM
7
Chapter 2: Maintenance & Troubleshooting
2.1 Maintenance
Servicing and safety
• Raymarine equipment should be serviced only by authorised Raymarine service technicians. They will ensure that servicing procedures and replacement
parts used will not affect performance. There are no user-serviceable parts in
any Raymarine product.
• Some products generate high voltages, and so never handle the cables/connectors when power is being applied to the equipment.
• When powered up, all electrical equipment produces electromagnetic fields.
These can cause adjacent pieces of electrical equipment to interact with one
another, with a consequent adverse effect on operation. In order to minimise
these effects and enable you to get the best possible performance from your
Raymarine equipment, guidelines are given in the installation instructions, to
enable you to ensure minimum interaction between different items of equipment, i.e. ensure optimum Electromagnetic Compatibility (EMC).
• Always report any EMC-related problem to your nearest Raymarine dealer.
We use such information to improve our quality standards.
• In some installations, it may not be possible to prevent the equipment from
being affected by external influences. In general this will not damage the
equipment but it can lead to spurious resetting action, or momentarily may
result in faulty operation.
Instrument
Certain atmospheric conditions may cause condensation to form on the
instrument window. This will not harm the instrument and can be cleared by
increasing the illumination setting to Level 3.
Periodically clean your ST60+ instrument with a soft damp cloth. Do NOT use
chemical and abrasive materials to clean the instrument.
Transducer
Refer to the Installation & Maintenance instructions supplied with the transducer.
81261_1.book Page 8 Friday, October 28, 2005 10:02 AM
8
ST60+ Speed Instrument Owner’s Handbook
Cabling
Examine all cables for chafing or other damage to the outer shield, and where
necessary, replace and re-secure.
2.2 Troubleshooting
Preliminary procedures
Changes in the electronic environment may adversely affect the operation of your
ST60+ equipment. Typical examples of such changes are:
• Electrical equipment has recently been installed or moved aboard your vessel.
• You are in the vicinity of another vessel or shore station emitting radio signals.
If you appear to have a problem, first ensure that the EMC requirements are still
being met before further investigating the problem.
Fixing faults
CAUTION: Prevention of flooding
If you need to remove the transducer insert, have the transducer
bung to hand and secure it in the transducer body immediately
after the insert has been removed, to prevent excessive ingress
of water.
All Raymarine products are subjected to comprehensive test and quality
assurance programmes prior to packing and shipping. However, if a fault occurs,
the following table may help to identify and rectify the problem.
Fault
Cause
Remedy
Display blank.
No power supply.
Check power supply & ensure the instrument is switched on (see Chapter 1,
Operation).
Check SeaTalk cabling and connector
security.
Check fuse/circuit breaker.
No transfer of information between SeaTalk
instruments (e.g. illumination levels).
SeaTalk cable or
connector fault.
Check security of SeaTalk connectors.
Check condition of SeaTalk cables.
Isolate faulty instrument by disconnecting instruments one by one.
Failure of a group of
SeaTalk instruments.
SeaTalk cable or
connector fault.
Check the security of SeaTalk connectors between functioning and non-functioning instruments.
81261_1.book Page 9 Friday, October 28, 2005 10:02 AM
Chapter 2: Maintenance & Troubleshooting
9
Fault
Cause
Remedy
No speed or temperature information.
Transducer cable or Check the condition of the transducer
connector fault.
cable and the security of the connections.
No speed information,
but temperature available.
Transducer paddle
wheel fouled.
Clean paddle wheel.
See CAUTION above.
Technical support
Raymarine provides a comprehensive customer support service, on the world
wide web and by telephone help line. Please use either of these facilities if you are
unable to rectify a problem.
World wide web
Please visit the Customer Support area of our web site at:
www.raymarine.com
As well as providing a comprehensive Frequently Asked Questions section and
servicing information, the web site gives e-mail access to the Raymarine Technical
Support Department and a details of the locations of Raymarine agents,
worldwide.
Telephone help line
If you do not have access to the world wide web, please call our help line.
In the USA, call:
• +1 800 539 5539, extension 2444 or
• +1 603 881 5200 extension 2444
In the UK, Europe the Middle East or the Far East, call:
• +44 (0) 23 9271 4713 (voice)
• +44 (0) 23 9266 1228 (fax)
Help us to help you
When requesting service, please quote the following product information:
• Equipment type.
• Model number.
• Serial number.
• Software issue number.
81261_1.book Page 10 Friday, October 28, 2005 10:02 AM
10
ST60+ Speed Instrument Owner’s Handbook
To find out the software version number of your ST60+ Speed instrument:
1. During normal operation, hold down the speed and trip buttons for approximately 4 seconds, to display the VERSION screen.
Software version
D8246-1
2. Note the software version number, then hold down the speed and trip buttons for approximately 2 seconds, to return to normal operation.
81261_1.book Page 11 Friday, October 28, 2005 10:02 AM
11
Chapter 3: Installation
This chapter describes how to install the ST60+ Speed instrument, and associated
speed transducer. The transducer is fitted in the hull of the vessel and signals from
it are connected by cable, to the rear of the instrument. The actual type of
transducer depends on the type of hull in which it is to be installed.
For advice, or further information regarding the installation of this equipment,
please contact the Raymarine Product Support Department or your own National
Distributor.
3.1 Planning your installation
Before starting the installation, spend some time considering the best positions
for both transducer and instrument, such that the Site requirements and the EMC
installation guidelines (below) are satisfied.
Site requirements
Transducer
2.0 in (51 mm)
diameter
2.94 in (75 mm)
diameter
0.19 in (5 mm)
4.69 in (119 mm)
2.94 in (75 mm )
diameter
Plastic through hull speed transducer dimensions
D8661-1
The transducer types required for the various hull types are as follows:
81261_1.book Page 12 Friday, October 28, 2005 10:02 AM
12
ST60+ Speed Instrument Owner’s Handbook
Hull material
Transducer type
Glass reinforced plastic (GRP)
E26031 Through hull plastic
Steel
E26031 Through hull plastic
Aluminium
E26031 Through hull plastic
Wood
M78716 Through hull bronze
Other transducer types are also available for specific requirements. For further
details, contact your local Raymarine dealer.
For accurate speed readings the transducer should be sited within the clear water
flow areas indicated by the shaded areas in the following diagram.
Sailing vessel
Planing power
vessel
Displacement power
vessel
Transducer siting
D4349-1
The transducer should also:
• Be ahead of the propellers (by a minimum of 10% of the water line length).
• Be at least 6 in (150 mm) away from the keel (ideally ahead of the keel if a sailing yacht).
• Be as near as possible to the center line of the vessel.
• Be clear of other through-hull fittings or projections.
• Have sufficient clearance inside the hull to fit the nut.
• Have 4 in (100 mm) of headroom to allow for withdrawal.
81261_1.book Page 13 Friday, October 28, 2005 10:02 AM
Chapter 3: Installation
13
There must also be a viable route for the transducer cable to be routed to the
instrument.
With standard bezel
(surface mount)
0.6 in
(15 mm)
With low profile bezel
(flush mount)
4.90 in (124 mm)
ST60+ instrument dimensions
490 in (124 mm)
0.93 in
(23.5 mm)
3.54 in (90 mm)
diameter
4.33 in (110 mm)
4.53 in (115 mm)
3.54 in (90 mm)
diameter
Instrument
0.25 in
1.4 in
(6.50 mm) (35 mm)
D8146-1
CAUTION: Keep the rear of the instrument dry
Keep the rear of instrument dry. Failure to observe this caution
could result in damage if water enters the instrument through
the breathing hole or comes into contact with the electrical
connectors.
ST60+ instruments can be fitted either above or below deck, provided the rear of
the instrument is sited where it is protected from contact with water.
Each instrument must also be positioned where:
• It is easily read by the helmsman.
• It is protected against physical damage.
• It is at least 9 in (230 mm) from a compass.
• It is at least 20 in (500 mm) from radio receiving equipment.
• There is reasonable rear access for installation and servicing.
81261_1.book Page 14 Friday, October 28, 2005 10:02 AM
14
ST60+ Speed Instrument Owner’s Handbook
EMC installation guidelines
All Raymarine equipment and accessories are designed to the best industry
standards for use in the recreational marine environment.
Their design and manufacture conforms to the appropriate Electromagnetic
Compatibility (EMC) standards, but correct installation is required to ensure that
performance is not compromised. Although every effort has been taken to ensure
that they will perform under all conditions, it is important to understand what
factors could affect the operation of the product.
The guidelines given here describe the conditions for optimum EMC performance,
but it is recognized that it may not be possible to meet all of these conditions in all
situations. To ensure the best possible conditions for EMC performance within the
constraints imposed by any location, always ensure the maximum separation
possible between different items of electrical equipment.
For optimum EMC performance, it is recommended that wherever possible:
• Raymarine equipment and cables connected to it are:
• At least 3 ft (1 m) from any equipment transmitting or cables carrying
radio signals e.g. VHF radios, cables and antennas. In the case of SSB
radios, the distance should be increased to 7 ft (2 m).
• More than 7 ft (2 m) from the path of a radar beam. A radar beam can normally be assumed to spread 20 degrees above and below the radiating
element.
• The equipment is supplied from a separate battery from that used for engine
start. Voltage drops below 10 V in the power supply to our products, and
starter motor transients, can cause the equipment to reset. This will not damage the equipment, but may cause the loss of some information and may
change the operating mode.
• Raymarine specified cables are used. Cutting and rejoining these cables can
compromise EMC performance and must be avoided unless doing so is
detailed in the installation manual.
• If a suppression ferrite is attached to a cable, this ferrite should not be
removed. If the ferrite needs to be removed during installation it must be reassembled in the same position.
Suppression ferrites
The following illustration shows typical cable suppression ferrites used with
Raymarine equipment. Always use the ferrites supplied by Raymarine.
81261_1.book Page 15 Friday, October 28, 2005 10:02 AM
Chapter 3: Installation
15
D3548-6
Connections to other equipment
If your Raymarine equipment is to be connected to other equipment using a cable
not supplied by Raymarine, a suppression ferrite MUST always be attached to the
cable near the Raymarine unit.
3.2 Procedures
As it is not practical to describe procedures for all possible installation scenarios,
the procedures given here describe the broad requirements for installing Speed
transducers and the ST60+ Speed instrument. Adapt these procedures as
appropriate, to suit your individual requirement.
CAUTION: Maintain structural safety
Where it is necessary to cut holes (e.g. for cable routing and
instrument mounting), ensure that these will not cause a hazard
by weakening critical parts of the vessel’s structure.
Unpacking
Unpack your ST60+ equipment and check that the items described in the Preface
are present.
Each ST60+ instrument is supplied with a standard bezel for surface mounting.
Optional mounting kits are available for flush mounting and bracket mounting
the instrument. If you have ordered the flush mounting option a flush mount bezel
and four fixing screws are also provided.
Fitting the instrument
The ST60+ Speed instrument can be installed using one of a number of different
mounting options:
• Surface mounting. Gives a profile of approximately 0.95 in (24 mm).
• Flush mounting. Gives a profile of approximately 0.25 in (6 mm).
• Bracket mounting.
The ST60+ instruments can also be mounted behind a panel with just the
instrument dial and buttons visible.
81261_1.book Page 16 Friday, October 28, 2005 10:02 AM
16
ST60+ Speed Instrument Owner’s Handbook
Surface mounting
Surface mounting
4
1 2
1
3
5
2
5
D8147-1
To surface mount your ST60+ instrument (see the Surface mounting illustration):
1. Ensure that:
• The selected location is clean, smooth and flat.
• There is sufficient space behind the selected location to accommodate the
rear of the instrument and connectors.
2. Apply the surface mount template (supplied at the rear of this handbook) to
the selected location and mark the centers for the fixing studs (1) and the
aperture (3) that will take the rear casing of the instrument.
3. Drill out the two 0.2 in (5 mm) fixing stud clearance holes (2).
4. Cut out the clearance hole (3) then remove the template.
5. Peel off the protective sheet from the self-adhesive gasket (4) then stick the
gasket into position on the rear of the instrument.
6. Screw the two fixing studs into the threaded sockets on the rear of the instrument.
7. Mount the assembled instrument, studs, bezel and gasket into the panel.
Secure from behind with the thumb nuts (5).
81261_1.book Page 17 Friday, October 28, 2005 10:02 AM
Chapter 3: Installation
17
Flush mounting
The Flush Mounting Kit uses a flush mount bezel to reduce the fitted profile of the
instrument, to approximately 0.25 in (6 mm) above the panel fascia.
D8148-1
Fitting the flush mount bezel
In order to flush-mount your ST60+ instrument, you must first replace the
standard bezel with the flush mount bezel as follows:
1. Hold the instrument in both hands with the display towards you.
2. Using both thumbs, gently press an upper corner of the instrument from the
bezel, then remove the bezel from the instrument. Retain the rubber keypad
which is released when the bezel is removed.
3. Referring to the Fitting the flush mount bezel illustration, insert the panel
seal (8) in the corresponding recess on the back of the flush mount bezel (7).
4. Place the instrument (11) face upwards on a flat surface, then place the rubber keypad (10) in position around the display window (i.e. so that each button outline is located over its associated button on the instrument).
5. Place the keypad seal (9) in position on the keypad (i.e. so that the holes in the
seal accept the appropriate keypad buttons).
6. Place the assembled flush mount bezel and panel seal, in position on the
instrument, so that the rubber keys are correctly located in the holes on the
bezel, then clip the bezel and instrument together.
CAUTION: Use the correct screws
It is essential that only screws of the correct size are used to
secure the instrument to the bezel. Failure to observe this caution
could result in damage to both the instrument and the bezel.
7. Using the four, self-tapping screws (12) provided, secure the instrument and
81261_1.book Page 18 Friday, October 28, 2005 10:02 AM
18
ST60+ Speed Instrument Owner’s Handbook
bezel together. Fit the screws from the rear of the instrument and tighten
them sufficiently to secure the instrument and bezel together. DO NOT OVERTIGHTEN.
Fitting the flush mount bezel
8
9
10
11
12
D8149-1
7
Flush mounting procedure
Flush mount your instrument (see the Flush mounting illustration) as follows:
1. Assemble the ST60+ instrument and flush mount bezel as described under
Fitting the flush mount bezel.
2. Ensure that:
• The panel on which you intend to mount the instrument is between
0.12 in (3 mm) and 0.78 in (20 mm) thickness.
• The selected location is clean, smooth and flat.
• There is sufficient space behind the selected location to accommodate the
rear of the instrument and connectors.
3. Apply the flush mount template (supplied at the rear of this handbook) to the
selected location and mark out the aperture into which the assembled instrument and bezel will sit.
81261_1.book Page 19 Friday, October 28, 2005 10:02 AM
Chapter 3: Installation
19
Flush mounting
1
4
3
1
5
6
5
D8150-1
4. Cut out the aperture (3) for the assembled instrument and bezel and remove
the template.
5. Peel off the protective sheet from the self-adhesive gasket (4) then stick the
gasket into position on the rear of the bezel.
6. Screw the two fixing studs (1) into the threaded sockets on the rear of the
instrument.
7. Mount the assembled instrument, studs, bezel and gasket into the panel.
8. Locate the flush mount bracket (6) onto the fixing studs and secure the assembly to the panel with the thumb-nuts (5).
Bracket mounting
A Control Unit Mounting Bracket (Part No. E25009) enables you to mount your
ST60+ instrument in locations where other forms of mounting are impractical.
Although this provides a useful alternative method for securing your instrument,
it is only suitable for use in positions where the instrument will not be exposed to
water.
To bracket mount your ST60+ instrument, do so in accordance with the Control
Unit Mounting Bracket Instruction Sheet.
81261_1.book Page 20 Friday, October 28, 2005 10:02 AM
20
ST60+ Speed Instrument Owner’s Handbook
Fitting transducer
The ST60+ Speed instrument is supplied, with a through-hull Speed transducer.
The Speed transducer is supplied with detailed instructions for installation and
maintenance. Before attempting to install the Speed transducer, read these
instructions and the Site requirements for transducers described in this Chapter.
Once you are satisfied you can meet all the installation requirements, install the
transducer in accordance with the accompanying installation instructions.
Running transducer cable
Each transducer type has a 14 m (45 ft) cable fitted with spade terminals for
connection to the ST60+ Speed instrument. The manner in which you run the
cable will depend on the locations of the transducer and instrument.
Observing the following guidelines, run the transducer cable to the ST60+ Speed
instrument:
• If the cable has to be fed through the deck, always use a proprietary deck
gland.
• Where cables are fed through holes, always use grommets to prevent chafing.
• Secure long cable runs so they do not present a hazard.
• Do not route the cable through bilges.
• Wherever possible, route the cable away from fluorescent lights, engines,
radio transmitting equipment, as these may cause interference.
• Although the transducer cable is fitted with spade connectors for direct connection to the rear of the instrument, it may be necessary to remove these to
facilitate installation, e.g. if the cable has to be routed through narrow apertures. Extra spade connectors are provided, to replace any that are removed
when running the cable. When fitting spade connectors, prepare the cable as
at (a) in the following illustration, then fold back the wire strands and insert
into the spade connector as at (b). Ensure the wire strands do not extend
beyond the rear of the spade connector insulation, then crimp the connector
to the wire.
50 mm
6 mm
(a)
(b)
3 mm
D4467-6
81261_1.book Page 21 Friday, October 28, 2005 10:02 AM
Chapter 3: Installation
21
Connecting the instrument
Types of connection
The ST60+ Speed instrument, can be connected:
• As a stand-alone, master instrument connected directly to the Speed transducer.
• As a SeaTalk repeater.
• To fulfil both repeater and master roles by being connected both to the transducer and to SeaTalk.
If instruments are connected to SeaTalk, no separate power connection is
necessary. Where a SeaTalk system includes an autopilot, the power for the
system is provided by the autopilot.
A range of Raymarine SeaTalk extension cables is available to connect separated
instruments. These cables are supplied with a SeaTalk connector fitted to each
end. A junction box can be used to join cables.
Signal connections
Make the necessary connections to your ST60+ instrument (see the Connection to
ST60+ Speed instrument illustration).
Cable from transducer
Connections to ST60+ Speed instrument
SeaTalk cable
Brown
White
Screen
Green
Red
D8151-1
SeaTalk cable
81261_1.book Page 22 Friday, October 28, 2005 10:02 AM
22
ST60+ Speed Instrument Owner’s Handbook
Power supply connections
CAUTION: Protect the power supply
Ensure that the 12 V power supply for the instrument is protected
by a suitably rated fuse or protective circuit breaker.
SeaTalk systems
Ensure that the power supply for the SeaTalk bus is protected by a 5 A fuse or
circuit breaker.
Systems with a large number of instruments on the SeaTalk bus may require
connections to the power supply from each end of the system (‘ring-main’ style),
to maintain sufficient voltage throughout the system.
This requirement depends on the total length of the cable run and the total
number of instruments in the system, as follows:
Cable run
No. of instruments
Power connections
Up to 10 m
13 maximum
26 maximum
1
2
Up to 20 m
7 maximum
13 maximum
1
2
Red
5 A fused,
12 V dc supply
(typically provided
by autopilot)
1
2
3
4
Screen
Instruments
5 to 16
Red
Screen
SeaTalk power connections
20
19
18
17
D4311-2
Stand alone instruments
Stand-alone instruments are not connected to SeaTalk and therefore need to be
connected to an alternative 12 V power source. Power cables are available in 2 m
and 9 m lengths.
81261_1.book Page 23 Friday, October 28, 2005 10:02 AM
Chapter 3: Installation
23
To fit a power cable:
1. Ensure the intended power source is switched off.
2. Run the power cable from the instrument to a suitable 12 V dc power source.
3 A over-current
circuit breaker
Red
12 V dc
supply
Screen
Power connections for stand-alone instrument
D4310-7
3. If the cable has not already been trimmed at the power supply end:
i. Cut the cable to length and trim back an appropriate amount of the outer
sheath.
ii. Cut back and insulate the yellow wire.
4. Connect the screen to the power supply 0 V terminal.
5. Connect the red wire, via a 3 A fuse or protective circuit breaker, to the power
supply +12 V terminal.
6. Insert the power cable connector into one of the SeaTalk connectors at the
rear of the instrument.
3.3 Switching on
Switch on the power to your ST60+ instrument. When the power is on, you can
use the speed button to switch the instrument on and off as described in
Chapter 1, Operation.
Use the procedures in Chapter 1, Operation to set the backlighting and contrast
how you want them.
WARNING: Calibration requirement
To ensure this product performs at its best on your boat, you
MUST calibrate it before use, in accordance with the instructions
in Chapter 4, Calibration. Do NOT use the product until you have
successfully calibrated it.
EMC conformance
Always check the installation before going to sea to make sure that it is not
affected by radio transmissions, engine starting etc.
81261_1.book Page 24 Friday, October 28, 2005 10:02 AM
24
ST60+ Speed Instrument Owner’s Handbook
81261_1.book Page 25 Friday, October 28, 2005 10:02 AM
25
Chapter 4: Calibration
4.1 Introduction
The ST60+ Speed instrument is set up with factory-programmed default settings,
so in order to optimise the performance of the instrument on board a particular
vessel, the procedures in this Chapter must be carried out immediately after the
completion of installation, and before the equipment is used for navigational
purposes.
Where practicable, the calibration procedures are presented diagrammatically, to
show the sequence of button presses and the resulting displays. Adjustment
instructions are given where applicable.
4.2 User calibration
The User calibration procedures enable you to:
• Set the required units for speed readings.
• Set the required Log units.
• Set the speed resolution.
• Set the speed readings on the instrument to be a true indication of the actual
speed of the vessel.
• Select temperature units.
• Calibrate for correct temperature readings.
• Set timer buzzer on or off.
• Set pop-up pilot display on or off.
To carry out a User calibration:
1. Power up the ST60+ Speed instrument.
2. Hold down the speed and trip buttons for approximately 2 seconds so that
the User calibration entry screen is displayed.
3. Referring to the User calibration diagram, carry out the calibration procedure. Use the speed button to move from screen to screen and the timer and
reset buttons to set the required values (except Adjust to SOG display).
Set speed units
Select either KTS (knots), MPH (miles per hour) or KMH (kilometers per hour),
as required.
81261_1.book Page 26 Friday, October 28, 2005 10:02 AM
26
ST60+ Speed Instrument Owner’s Handbook
Set resolution
Select resolution of either 0.01 or 0.1 as required.
Set log units
Select either NM (nautical miles), SM (statute miles) or KM (kilometers), as
required.
Setting the correct speed
Set the displayed (current) speed using one of the following methods:
• If SOG is available from SeaTalk, use the Adjust to SOG screen to automatically set the current speed to. You must be running in slack tide conditions to
successfully use this method.
• Manually apply a calibration factor by means of the Cal factor adjust screen,
to set the displayed speed value to your best estimate of the vessel’s speed.
If neither of the above methods is suitable, use the Speed calibration procedure
described underIntermediate calibration to carry out a speed calibration run over
a measured distance. This enables the instrument to calculate the correct
calibration factor.
Adjust to SOG
The Adjust to SOG screen is displayed only if SOG data is available from SeaTalk.
The current SOG is displayed in the top right of the display (12.8 in the
illustration), and the current speed registered by the instrument is shown as large
figures (12.4 in the illustration).
It is recommended that, if you are running in slack tide conditions, you press the
reset button for 3 seconds, to accept the SOG as the current speed. The
calibration factor is automatically re-calculated.
If you do not wish to accept SOG as the current speed, simultaneously press the
timer and reset buttons to select the Cal factor adjust screen.
81261_1.book Page 27 Friday, October 28, 2005 10:02 AM
Chapter 4: Calibration
Hold down speed and
27
for approximately 2 seconds
trip
Speed units
Speed
resolution
speed
speed
speed
To set the required values at
each User cal screen, press
EITHER
timer
Set Log
units
OR reset
(not applicable to Adjust to SOG
screen)
speed
speed
Pop-up
pilot
Set correct
speed
If SOG available from
SeaTalk
Adjust
to SOG
speed
Timer
buzzer
If SOG NOT
available
reset
Timer
buzzer
Adjust
Cal Factor
+
timer
speed
speed
Temperature
calibration
To leave User cal, hold down
speed
+
Temperature
units
trip
for approximately 2 seconds
User calibration
D8152-1
speed
81261_1.book Page 28 Friday, October 28, 2005 10:02 AM
28
ST60+ Speed Instrument Owner’s Handbook
Adjust cal factor
The adjust cal factor screen enables you to manually adjust the calibration factor.
It shows the current calibration factor in the top right of the display, and the
current speed as large figures (12.4 in the illustration).
Use the timer or reset button to adjust the calibration factor so that the current
speed equals the speed through the water.
If SOG data is available from SeaTalk, you can turn to the Adjust to SOG screen by
pressing the timer and reset buttons.
Note: If neither of the above methods gives satisfactory results, carry out the Speed calibration procedure (part of Intermediate calibration).
Set temperature units
Select either °C or °F , as required.
Temperature calibration
Set the display to show the current water temperature.
Timer buzzer
Switches the count-up and race-start timer buzzers on and off.
Pop-up pilot
Switches the pop-up pilot function on and off.
Leaving User calibration
Hold down the speed and trip buttons for 2 seconds to save your settings, exit
User calibration and resume normal operation.
4.3 Intermediate calibration
Intermediate calibration enables you to:
• Check the instrument software version.
• Check the instrument status - either MASTER (transducer connected) or
REPEATER (no transducer).
• Carry out a calibration run over a measured distance to ensure accurate speed
readings.
To start Intermediate calibration, hold down the speed and trip buttons for
approximately 4 seconds (see Intermediate calibration flow chart).
81261_1.book Page 29 Friday, October 28, 2005 10:02 AM
Chapter 4: Calibration
Hold down speed and
29
trip
for approximately 4 seconds
Software
version
Instrument
status
speed
(or REPEATER)
speed
Carry out speed calibration
as detailed in
Speed calibration - sheets 1 & 2
Intermediate calibration
D8153-1
speed
Speed calibration
This speed calibration procedure involves carrying out two runs over a measured
distance, to enable a calibration factor to be determined and applied to your
ST60+ Speed instrument, to ensure optimum accuracy. Each calibration run
comprises outward and return legs, to minimise the affect of tidal drift when the
calibration factor is determined.
To carry out a speed calibration, start the Intermediate calibration procedure and
use the speed button to proceed to the Calibration run length screen (see sheet 1
of the Speed calibration flow chart). Proceed with the speed calibration as
follows:
1. With the Calibration Run Length screen displayed, press the timer and reset
buttons together to enter adjust mode. In this mode, the displayed run length
flashes on and off.
2. Set the length of the intended calibration run, using either the timer button
to decrement or the reset button to increment the run length value. You can
set any value between 0.25 and 2.50.
3. Press timer and reset buttons together to commence the speed calibration.
The Cal status screen is displayed. The text at the top of the screen alternates
between START 1 and the calibration factor currently applied.
4. Start the outward leg of the calibration run and as you pass the start point,
press the trip button, so the screen shows OUTWARD at the top. As the
calibration run proceeds, the displayed value will increment.
81261_1.book Page 30 Friday, October 28, 2005 10:02 AM
30
ST60+ Speed Instrument Owner’s Handbook
from Intermediate calibration
(Instrument status display )
Use either
timer or reset
to set length of calibration run
Calibration
run
length
At the end
of the
outward cal
run press
timer
timer
+
+
reset
reset
At the start of
the outward leg
press
Complete the
outward leg of
the first cal run
trip
trip
At the start of
the return leg
press
Complete the
return leg of
the second cal run
trip
At the end of the
return leg press
trip
Carry out
second
calibration run
Exit speed
You can now either carry calibration
out a second cal run or
exit speed calibration
speed
Speed calibration, sheet 1
+
trip
to save the
cal factor
Go to sheet 2
Exit to Instrument status
display (Intermediate
calibration)
D8154-1
This is the
end of the
first cal run
81261_1.book Page 31 Friday, October 28, 2005 10:02 AM
Chapter 4: Calibration
Complete the
outward leg of
the second cal run
At the end of the
outward leg, press
At the start of the
return leg press
Complete the
return leg of
the second cal run
At the end of
the return leg
press
trip
trip
Speed calibration
is now complete
Press
speed
+
trip
to save the
cal factor
Speed calibration, sheet 2
trip
Exit to Instrument
status display
(Intermediate
calibration)
D8155-1
trip
From sheet 1
31
5. At the end of the outward leg, press the trip button again so that:
• The text RETURN is flashing at the top of the screen.
• The displayed distance freezes. Note that this value may not be the same
as the measured distance, due to errors introduced by tidal flow.
6. Turn the vessel round, start the return leg and as you do so, press the trip button so RETURN stops flashing and the displayed value increments.
7. At the end of the return leg, press the trip button. At this point:
• The text START 2 alternating with the new calibration factor is displayed at the top of the screen.
• The displayed distance freezes. This value should be very close to the
actual (measured) distance of the calibration run.
8. Carry out one of the following actions:
• If you are satisfied with the results of the first calibration run, press the
speed and trip buttons together, to store the new calibration factor, exit
speed calibration and return to the Instrument status screen.
81261_1.book Page 32 Friday, October 28, 2005 10:02 AM
32
ST60+ Speed Instrument Owner’s Handbook
• If you want to carry out a second calibration run:
i. Press trip to start the second calibration run (see sheet 2 of the
Speed calibration flow chart).
ii. Use the procedure described above in steps 4 to 7, to complete the
second run. At the end of the second run, the text END alternating
with the new calibration factor is displayed at the top of the screen.
iii. Press the speed and trip buttons together, to store the new calibration factor, exit speed calibration and return to the Instrument status
screen.
Leaving Intermediate calibration
Hold down the speed and trip buttons for 2 seconds to save your settings, exit
Intermediate calibration and resume normal operation.
4.4 Dealer calibration
The Dealer calibration procedure (see Dealer calibration diagram) enables the
following parameters to be set:
• User calibration on/off.
• Speed response.
• VMG response.
• Boat show mode on/off.
Dealer calibration also gives access to the Factory defaults screen. This enables
you to re-apply the factory settings if you want to reset the instrument to a known
operating condition.
To commence Dealer calibration, hold down the speed and trip buttons
together for approximately 12 seconds, to select the Dealer calibration entry
screen. Press the timer and reset buttons together, to proceed with the
calibration, then use the speed button to proceed from screen to screen as
calibration progresses.
User calibration on/off
Press the timer or reset buttons to toggle the User calibration either ON or
OFF as required. With OFF selected, User calibration and Intermediate
calibration are both disabled.
81261_1.book Page 33 Friday, October 28, 2005 10:02 AM
Chapter 4: Calibration
33
Hold down speed
+
trip
for approximately 12 seconds
Entry screen
+
timer
Factory defaults
reset
Speed
response
Calibration
on/off
speed
speed
Boat show
mode
speed
timer
Use
or reset
to set required values
speed
VMG
response
speed
To leave calibration,
hold down
Dealer calibration
+
trip
for approximately 2 seconds
D8156-1
speed
Response settings
The response values for both SPEED and VMG determine the frequency at
which information is updated. A low number provides a smooth response and a
high number a much livelier update.
Use the timer (decrement) and reset (increment) buttons to set the required
value. Response values are from 1 to 15 .
81261_1.book Page 34 Friday, October 28, 2005 10:02 AM
34
ST60+ Speed Instrument Owner’s Handbook
Boat show mode
CAUTION: Do NOT enable Boat Show Mode
Do NOT enable Boat Show Mode. This must be used only for
demonstration purposes.
Ensure that the Boat Show Mode is set to OFF . If necessary, use the timer or
reset button to achieve this.
Factory defaults
You can use this screen to reset the operating parameters to the factory default
values. Use the timer and reset buttons to make the required selection.
Note that the selection you make at this screen will be applied when you exit the
screen, so be sure you make the correct selection.
To retain the current values, ensure that the display shows NO.
If you want to apply the factory defaults, change the display to YES. If you do
this, the values you have set up will be overwritten by the factory defaults when
you leave this screen.
Leaving Dealer calibration
Hold down the speed and trip buttons for 2 seconds to save your settings, exit
Dealer calibration and resume normal operation.
81261_1.book Page 35 Friday, October 28, 2005 10:02 AM
35
Glossary
APP
Apparent
AVE
Average
AWA
Apparent Wind Angle (relative to the vessel)
AWS
Apparent Wind Speed
BTW
Bearing To Waypoint
CMG
Course Made Good
COG
Course Over Ground
DMG
Distance Made Good
DTW
Distance To Waypoint
EMC
Electro Magnetic Compatibility
ETA
Estimated Time of Arrival
GPS
Global Positioning System
HDG
Heading
KM
Kilometer(s)
KMH
Kilometers per hour
KTS
Knot(s)
LAT
Latitude
LCD
Liquid Crystal Display
LON
Longitude
LTR
Liter(s)
81261_1.book Page 36 Friday, October 28, 2005 10:02 AM
36
ST60+ Speed Instrument Owner’s Handbook
M
Magnetic or meters
MAG
Magnetic
MOB
Man Overboard
MPH
Miles per hour
NM
Nautical mile(s)
Response
The sensitivity of an instrument, to data changes
RF
Radio Frequency
SeaTalk
Raymarine proprietary communication system which links products, to provide a
single, integrated system sharing power and data
SM
Statute mile(s)
SOG
Speed Over Ground
SPD
Speed
T
True
TTG
Time To Go
TWA
True Wind Angle relative to the vessel, taking into account the speed of the vessel
TWD
True Wind Direction
TWS
True Wind Speed
VMG
Velocity Made Good
WP
Waypoint
XTE
Cross Track Error
81261_1.book Page 37 Friday, October 28, 2005 10:02 AM
37
Index
A
L
Average speed, 3
Log screen, 3
B
M
Backlighting adjustment, 6
Boat log, 3
Boat show mode, 34
Boat speed, 2
Buzzer, 5
Maximum speed, 2
Mounting options (instrument), viii, 15
P
Calibration requirement, 1, 23
Cleaning, 7
Condensation, 7
Contrast adjustment, 6
Parts supplied, ix
Pop-up pilot, 6
switch on/off, 28
Power supply
SeaTalk systems, 22
stand alone instrument, 22
Product disposal, ii
D
R
C
Factory defaults, 34
Race start timers, 5
buzzer, 5
settings, 5
Remote control, viii, 6
Reset
average speed reading, 3
maximum speed reading, 2
trip distance reading, 4
H
S
Dealer calibration, 32
Display setup, 6
Disposing of the product, ii
E
EMC information, i, 7, 14, 23
F
Help lines, 9
I
Installing
instrument, 15
bracket mounting, 19
flush mounting, 17
power supply connections, 22
requirements, 13
signal connections, 21
surface mounting, 16
planning, 11
transducer, 20
requirements, 11
running cable, 20
Instrument mounting options, viii, 15
Intermediate calibration, 28
Safety
calibration requirement, 1, 23
electrical, i
general, i
navigation, i
SeaTalk overview, vii
Servicing & safety, 7
Setting
contrast, 6
Setting up
applying factory defaults, 34
backlighting, 6
correct speed, 26, 29
distance units, 26
instrument response, 33
race start timer, 5
81261_1.book Page 38 Friday, October 28, 2005 10:02 AM
38
resolution, 26
speed units, 25
temperature reading, 28
temperature units, 28
User calibration access, 32
Site requirements
instrument, 13
transducer, 11
Software version, 10, 28
Speed calibration
methods, 26
procedure, 29
Speed information, 2
average speed, 3
boat speed, 2
maximum speed, 2
Speed Over Ground, 3
Velocity Made Good, 3
Switching on/off, 1, 23
ST60+ Speed Instrument Owner’s Handbook
T
Technical support, 9
Temperature (water), 4
Timers, 4
buzzer, 5
switch buzzer on/off, 28
race start timers, 5
setting, 5
Trip distance, 4
Troubleshooting, 8
U
User calibration, 25
V
Velocity Made Good, 3
W
Water temperature, 4
81261_1.book Page 39 Friday, October 28, 2005 10:02 AM
Remove material
from shaded areas only
Sun cover edge
Instrument edge
1.185 in (30.1 mm)
1.18 in (30.0 mm)
SURFACE MOUNT template for
ST60+ Instruments
D8157-1
Cut hole
3.54 in (90 mm)
diameter
1.77 in (45.0 mm)
Drill hole, 3/16 in (5 mm)
diameter in 2 positions
TOP
1.76 in (44.6 mm)
SURFACE MOUNT
Template
81261_1.book Page 40 Friday, October 28, 2005 10:02 AM
81261_1.book Page 41 Friday, October 28, 2005 10:02 AM
TOP
Control Unit
Drill hole,
1/4 in (6.5 mm)
diameter in
4 positions
FLUSH MOUNT
Template
4.47 in (113.5 mm)
Remove material from shaded area only
4.3 in (109 mm)
Sun cover edge
Instrument edge
FLUSH MOUNT template for
ST60+ Instruments
81261_1.book Page 42 Friday, October 28, 2005 10:02 AM
81261_1.book Page I Friday, October 28, 2005 10:02 AM
Raymarine World Wide Warranty
I
Raymarine World Wide Warranty
Raymarine Inc.
APPLICABLE TO PRODUCTS SOLD THROUGH OFFICIAL RAYMARINE INC. DEALERS, DISTRIBUTORS AND BOAT
BUILDERS WITHIN THE AMERICAS AND CARIBBEAN.
Limited warranty
Subject to the terms, conditions and limitations set forth in this U.S. Limited Warranty (hereinafter the ‘Warranty’),
Raymarine warrants that its products, when properly installed and used, will be free from defects in material and
workmanship for a period of twenty-four (24) months (with respect to VHF radios, a period of thirty-six (36) months),
from the date of first purchase (the ‘Warranty Period’).
For the purposes of this warranty, ‘date of first purchase’ means the date that the product was purchased by the first
retail customer; or in the case of a product installed on a new vessel by a certified Raymarine original equipment
manufacturer (a ‘Raymarine OEM’), the date that such vessel was purchased by the first retail customer.
Raymarine will, at its sole option, repair or replace any defective products or components returned during the
Warranty Period in accordance with the terms, conditions and limitations set forth below. Such repairs or
replacement will be the sole remedy of the customer under this Warranty.
Obtaining Warranty Service
Standard Warranty Service
To qualify for standard warranty service the product must be returned to a Raymarine-certified service agent, or
directly to Raymarine in person, or by mail (i) within the Warranty Period, and (ii) within thirty (30) days of the alleged
product failure.Any products returned by mail must be securely packaged and sent pre-paid and insured to
Raymarine or to a Raymarine-certified service agent. All products, whether returned in person or by mail, must be
accompanied by a copy of the original sales receipt, to be eligible for standard warranty service.
A list of Raymarine-certified service agents is available from Raymarine Technical Support or at
www.raymarine.com
‘On Board’ Warranty Service
For any Raymarine product or system that (i) has been installed on your vessel by a Raymarine-certified service agent
or by a Raymarine OEM, and (ii) has a MSRP equal to or greater than USD $2,500, you are eligible to receive warranty
service by a Raymarine certified service agent on-board your vessel (‘On Board Warranty Service’) for a period of 12
months from the date of first purchase of such product or system, or the date of first purchase of the vessel on which
such product or system has been installed (the ‘On Board Warranty Period’). In order to obtain On Board Warranty
Service eligible customers MUST:
•
(i) within the On Board Warranty Period, and (ii) within thirty (30) days from the date of the alleged failure
giving rise to the warranty claim for which you are requesting On Board Warranty Service, contact a local
Raymarine-certified service agent and request On Board Warranty Service.
• Present to the Raymarine-certified service agent a copy of the original sales receipt for the product,
together with proof of the date of installation of the product by a Raymarine-certified service agent. The
service agent may at its sole option, accept or deny such proof of purchase and proof of installation as sufficient to qualify you for On Board Warranty Service.
Costs associated with travel, mileage, taxi fares, launch or docking fees, aircraft or vehicle rental, meals, customs,
shipping, communication charges, and service agent travel costs are specifically excluded from coverage under this
Warranty and are your responsibility. In addition, this Warranty does not cover fees associated with hauling,
shipping or towing your vessel to a Raymarine-certified agent.
81261_1.book Page II Friday, October 28, 2005 10:02 AM
II
Upon the expiration of the On Board Warranty Period, you are still eligible to receive standard warranty service for the
remaining term of the Warranty Period, but will not be eligible for continued On Board Warranty Service.
Limitations and Exclusions
In addition to any other limitations and exclusions set forth herein, Raymarine is not responsible for, and this
Warranty does not cover:
•
•
•
•
•
•
•
failures due to abuse, misuse, accident, unauthorized alteration or repair, improper installation (whether or
not by a Raymarine-certified service agent), shipping damage or corrosion;
Costs associated with routine system checkouts, alignment/calibration, seatrials or commissioning;
repair or replacement of consumable items, including, without limitation, fuses, batteries, drive belts, radar
mixer diodes, snap-in impeller carriers, impellers, impeller bearings and impeller shafts;
costs associated with overtime or premium labor costs;
differences in material, coloring or size that may exist between actual products and the pictures or descriptions of such products in our advertising, advertising literature or on the Internet;
products purchased by a customer from a United States dealer via the Internet if such products were not
delivered and installed within the United States; or
the replacement of missing components from the package of any product purchased through an online
auction site.
Other conditions
This Warranty is fully transferable provided that you furnish the original proof of purchase to Raymarine or, in the case
of On Board Warranty Service, to a Raymarine-certified service agent. This Warranty is void if the label bearing the
serial number has been removed or defaced.
TO THE EXTENT CONSISTENT WITH STATE AND FEDERAL LAW, THE FOREGOING WARRANTY IS
RAYMARINE’S SOLE WARRANTY AND IS APPLICABLE ONLY TO NEW PRODUCTS PURCHASED IN THE
UNITED STATES OF AMERICA. THE PROVISIONS OF THIS WARRANTY ARE IN LIEU OF ANY OTHER WRITTEN
WARRANTY, WHETHER EXPRESSED OR IMPLIED, WRITTEN OR ORAL, INCLUDING ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
THE LIABILITY OF RAYMARINE TO A CUSTOMER UNDER THIS WARRANTY, WHETHER FOR BREACH OF CONTRACT,
TORT, BREACH OF STATUTORY DUTY OR OTHERWISE SHALL IN NO EVENT EXCEED AN AMOUNT EQUAL TO TEN (10)
TIMES THE MANUFACTURER’S SUGGESTED RETAIL PRICE OF THE PRODUCT GIVING RISE TO SUCH LIABILITY AND
IN NO EVENT SHALL RAYMARINE BE LIABLE FOR SPECIAL, INCIDENTAL, CONSEQUENTIAL OR INDIRECT DAMAGES.
SOME JURISDICTIONS DO NOT ALLOW EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU
SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM JURISDICTION TO
JURISDICTION.
This Warranty supersedes and replaces all previous Warranties.
January 2005
81261_1.book Page III Friday, October 28, 2005 10:02 AM
Raymarine World Wide Warranty
III
Raymarine UK Ltd.
APPLICABLE TO PRODUCT SOLD THROUGH OFFICIAL RAYMARINE UK LTD. DEALERS, DISTRIBUTORS AND BOAT
BUILDERS WITHIN EUROPE, THE MIDDLE AND FAR EAST, AFRICA AND AUSTRALASIA.
Limited Warranty
The Raymarine warranty terms and conditions as described below do not affect the customers legal rights and
complies with EU Directive 1999/44/EC.
In order to ensure that the product continues to operate efficiently and reliably, we recommend that, before using the
product, the customer carefully reads the Owner’s Handbook and follows the advice on the safe and correct
operation and use of the product. We recommend that the Raymarine product is installed by a Raymarine certified
installer. Installation by persons other than a Raymarine certified installer may invalidate the warranty.
1. Product warranty
1.1 Raymarine warrants each new product to be of good materials and workmanship. Raymarine, or its approved
agents, will repair or exchange under warranty any parts or product proven to be defective in material or
workmanship under normal use, for a period of 2 years (24 months) from date of sale to end user, subject to the limits
contained in this warranty document.
1.2 The Raymarine warranty covers the parts and labour associated with any warranty repair as described above,
provided that the product is returned to Raymarine or one of its approved agents.
1.3 Raymarine reserve the right to replace under warranty, not repair, certain Raymarine products subject to the
limitations below, provided that they are returned to the nearest Raymarine National Distributor. For details of such
products refer to the internet at www.raymarine.com or contact your nearest Raymarine National Distributor.
2. Onboard warranty
2.1 In addition to the Product warranty cover as described above, Raymarine will, authorize onboard warranty service
by the nearest Raymarine approved service agent, subject to the maximum mileage and other limits referred to in
paragraph 4.12 below, on products, where proof of installation, or commission by Raymarine certified installers, can
be shown.
2.2 The warranty provides for onboard repair or exchange of the product, by Raymarine or its approved service
agents, for a period of 2 years (24 months), subject to the limits contained in this warranty document. In the case of a
product installed, by a Raymarine certified OEM installer, on a new boat prior to the sale of the boat to a customer, the
2-year period will begin on the date of the sale of the boat to the customer. In the case of a product installed, by a
Raymarine certified installer, on a boat already in the possession of the customer, the 2-year period will begin on the
date of the commissioning of the installed product.
2.3 Certain Raymarine products are not covered by onboard warranty unless the products are pre-registered and on
board warranty is purchased from the Raymarine certified installer. For details of such products refer to the internet at
www.raymarine.com or contact your nearest Raymarine National Distributor.
2.4 The Purchaseable onboard warranty is subject to the limitations below.
3.Obtaining warranty service
3.1 In the event of warranty service being required, the customer should contact Raymarine Technical Support or the
nearest Raymarine approved service agent - the contact details of Raymarine Technical Support and a full list of the
names and details of worldwide service agents are available on the internet at www.raymarine.com and in the
Owner’s Handbook.
81261_1.book Page IV Friday, October 28, 2005 10:02 AM
IV
3.2 In cases where the customer is requesting a warranty service and a Raymarine certified installer has not installed
the product; i.e. Product warranty, the affected product must be returned to the customer’s local Raymarine approved
service agent or direct to Raymarine with:
3.2.1 proof of purchase showing the date of purchase and the name of the supplier of the product; and
3.2.2 the serial number of the affected product; or
3.2.3 a warranty card completed by the product supplier (which will contain the information required by
paragraphs 3.2.1 and 3.2.2).
Subject to the limitations below, the product will be repaired or replaced (at the discretion of Raymarine or a
Raymarine Service Agent) at no further cost and promptly returned to the customer.
3.3 In cases where the customer is making a warranty claim and the product has been installed by a Raymarine
certified installer, (boat builder, installer, dealer etc.) i.e. Onboard warranty, the nearest Raymarine approved service
agent should be contacted and onboard service requested (which will be subject to the limits referred to in paragraph
4.12 below). Before the onboard warranty service is performed, the customer must have available:
3.3.1 proof of purchase showing the date of purchase and the name of the supplier of the product; and
3.3.2 the serial number of the affected product; or
3.3.3 proof of installation of the product by a Raymarine certified installer; or
3.3.4 a warranty card completed by the product supplier (which will contain the information required by
paragraphs 3.3.1 and 3.3.3).
3.4 In cases where onboard warranty has been purchased - as described in 2.3; the nearest Raymarine approved
service agent should be contacted and onboard service requested, information detailed in 3.3.1 and 3.3.2 is required.
Onboard warranty service will only be performed if the product serial number confirms that the onboard warranty
service has been purchased and is valid.
4. Warranty limitations
4.1 Raymarine warranty policy does not apply to any product that has been subjected to accident, abuse or misuse,
shipping damage, alterations, corrosion, incorrect and/or non-authorized service, or products on which the serial
number has been altered, mutilated or removed.
4.2 Certain products do not carry the onboard warranty, as described in section 2 above, unless the onboard warranty
cover is purchased at the time of installation. The purchaseable onboard warranty is only available on products
purchased in specific territories, for further details refer to the internet at www.raymarine.com or contact your
nearest Raymarine National Distributor.
4.3 Products purchased outside the country of installation will not be covered by onboard warranty.
4.4 Raymarine assumes no responsibility for damage incurred during installation or as a result of improper
installation.
4.5 This warranty does not cover routine system checkouts, alignment/calibration, seatrials or commissioning, unless
required by replacement of part(s) in the area being aligned.
4.6 Raymarine assumes no responsibility for damage caused by or to other equipment, systems or components
occasioned by improper or unauthorized connection, or use, of the product.
4.7 Consumable items, including, but not limited to: fuses, batteries, drive belts, radar mixer diodes, snap-in impeller
carriers, impellers, impeller bearings, and impeller shafts are specifically excluded from this warranty. A complete list
of the consumable items relating to each product can be found in the Owner’s Handbook and/or on the internet at
www.raymarine.com.
4.8 All costs associated with transducer replacement, other than the cost of the transducer itself, are specifically
excluded from this warranty.
4.9 Overtime/premium labour portion of services outside of normal working hours is not covered by this warranty.
81261_1.book Page V Friday, October 28, 2005 10:02 AM
Raymarine World Wide Warranty
V
4.10 If repairs are necessary under the warranty, the affected product must be forwarded to a Raymarine facility or a
Raymarine approved service agent, at the owner’s expense.
4.11 The Raymarine warranty does not cover any differences in material, coloring or size between those alluded to in
corporate advertising, literature or published on the internet, which are not specifically objected to at the time of
delivery.
4.12 Travel costs other than auto mileage, tolls and two (2) hours travel time, are specifically excluded from the
warranty on all products. Costs, which are excluded from the coverage of this warranty, include but are not limited to;
taxi fares, launch fees, aircraft rental, subsistence, customs, shipping, and communications charges etc.
4.13 Neither Raymarine nor a Raymarine service agent shall be liable for any incidental, indirect, consequential or
special (including punitive or multiple) damages, nor shall Raymarine or a Raymarine service agent be liable for any
loss of profit, business, contracts, opportunity, goodwill or other similar loss. The liability of Raymarine or a Raymarine
service agent to a customer under this warranty, whether for breach of contract, tort, breach of statutory duty or
otherwise, shall not exceed US$1,000,000. Nothing in this paragraph 4.13 shall limit the liability of Raymarine or a
Raymarine service agent in respect of death or personal injury caused by its negligence, fraud or any other liability
which by law, cannot be excluded or limited.
4.14 All Raymarine products sold or provided hereunder are merely aids to navigation. It is the responsibility of the
user to exercise discretion and proper navigational skill independent of any Raymarine product.
Document Number 80009_1
January 2005
81261_1.book Page VI Friday, October 28, 2005 10:02 AM
VI
Raymarine Service Centers
North and South America
Europe, Middle East, Africa
and Australasia
Raymarine Technical Support
1-800-539-5539
or, +1 603-881-5200
Raymarine Technical Support
+44 (0) 23 9271 4713
Product Repair and Service
Raymarine Product Repair Center
21 Manchester Street,
Merrimack,
NH 03054-4801
USA
Product Repair and Service
Raymarine plc
Anchorage Park
Portsmouth
PO3 5TD
England
Help us to help you
To allow us to respond to your needs faster, please quote the Equipment type,
Model number and Serial number when requesting service
Stick barcode label here
Purchased from
Purchase date
Dealer address
Installed by
Installation date
Commissioned by
Commissioning date
Owners name
Mailing address
D8033-1
Complete product information and interactive help is available at:
www.raymarine.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising