Chap. 3: Installation Precautions

Chap. 3: Installation Precautions
Chapter 3 Installation Precautions
Danger
1. While installing the FB-PLC or other equipment connected, turn off all power supplies otherwise, electrical
shock, or damage to machines and equipment may occur.
2. Cover the protection board on the terminal block and supply power for testing after completion of all installation
and wiring operation in order to avoid electrical shock.
3. Never peel off the dust proof film on the ventilation holes of the PLC before completion of installation and wiring.
This is necessary in order to prevent dropping of iron chips from drilling and other wire scraps into the PLC and
causing damage to the PLC internal circuitry.
4. Remember to peel off the above stated dust-proof film after confirming completion of installation and wiring to
prevent poor heat dissipation of the PLC and prevent damage to the unit from excessive heat.
3.1 Installation Environment
Caution
1. The working environment specification of the FB-PLC should never exceed the environmental specification
listed in section 1.5 in this manual. Besides, never use in environment with fume, conductive dust, high
temperature, corrosive gas, combustible gas, rain, saturated humidity, and vibration impact places.
2. Whether used in a system or as a stand alone unit, this product should be installed in an appropriate cabinet,
the selection of the cabinet and installation should comply with local or national standard requirement.
3.2 Layout of Control Board and Mounting of the PLC
Placing of the PLC
The mounting design of the FB-PLC is facing transversely in front(horizontal position) and placed
from left (main unit) to right (expansion unit/module), it can be fixed by using DIN RAIL or
mounting screws, the figure below is the typical mounting method:
+24V IN-
+24V IN-
+24V IN-
The example of
multiple
expansion
modules link
3-1
Heat Dissipation Clearance
The FB-PLC uses natural air convection for heat dissipation, thus sufficient gap
should be provided for heat dissipation.
A min. of 25mm gap should be provided above and below the unit.
There should be a minimum of 50mm clearance above the face of the PLC.
the direction of
heat dissipating
Mounting Method
DIN RAIL (DIN EN50022) mounting method
• This method is not applicable to applications with high vibration condition exceeding 0.5G.
• Pull the two DIN RAIL removal tab hooks at the bottom of the PLC simultaneously while pushing the PLC from
top to bottom.
Direct mounting by screws M3~M4 screw fixing method.
• Use M3~M4 screw holes to directly mount on control cabinet.
• There are three types of fixing holes for various models of FB-PLC as follows:
3-2
SIZE A:
FBE-28
Mounting holes
(M4 or no.8)
SIZE B:
FBE-40
Mounting holes
(M4 or no.8)
SIZE C:
Mounting holes
(M4 or no.8)
FB8
FB-PLC Mounting holes
3.3 Precautions in Construction and Wiring
1. Please follow local or national standard regulations to proceed with installation and wiring of the FB-PLC.
2. Please notice the current load of the I/O wiring and choose the appropriate wire size.
3. Use as short as possible wires, the I/O wiring should not exceed 100m in any circumstance (less than 10m for high
speed inputs).
4. The input wiring should be away from output or power lines (a distance of 30~50mm), make perpendicular crossing if
separation is not possible, never run both in parallel.
5. There are two kinds of terminal blocks with the pitch of 9.52mm and 7.62mm, the torque ranges of screw are shown
below:
M3.5
9.52mm
Terminal Block
<8mm
torque: 1 0 ~ 1 2 k g / c m
<8mm
M3
7.62mm
Terminal Block
M3.5
M3
<6mm
<6mm
3-3
torque:6~8kg/cm
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising