Radio Shack 43-3548 Owner`s manual

Radio Shack 43-3548 Owner`s manual
43-3548.fm Page 1 Tuesday, February 25, 2003 1:06 PM
2.4 GHz Cordless Telephone
Caller ID/Call Waiting ID
43-3548
20-Number Memory Dialing — lets you store up to 20 numbers in memory
for easy dialing. (See “Storing Phone Numbers and Names” on page 20.)
Ample Talk and Standby Time —
the supplied battery (when fully
charged) provides about 7 hours of
talk time or 14 days of standby time.
Headset Jack — lets you connect an
optional headset for hands-free
convenience. (See “Using a Headset”
on page 33.)
Auto Talk— lets you
set the phone to
answer a call by simply
lifting the handset from
the base.
!
!
IMPORTANT
If an icon appears at the end of a paragraph, go to the box on that page with the
corresponding icon for pertinent information.
o — Warning
! — Important
OWNER’S MANUAL
— Caution
Ó — Hint Ô — Note
Please read before using this equipment.
© 2003 RadioShack Corporation.
All Rights Reserved.
RadioShack and RadioShack.com are trademarks
used by RadioShack Corporation.
ENERGYSTAR and the ENERGYSTAR certification mark
are registered US marks.
43-3548.fm Page 2 Tuesday, February 25, 2003 1:06 PM
CONTENTS
Important Information . 2
FCC Statement .......... 2
Surge Proection ......... 3
Important Information
Important Safety
Instructions ............... 4
As an ENERGYSTAR Partner,
RadioShack Corporation has
determined that this product
meets the ENERGYSTAR guidelines
for energy efficiency.
Battery Safety
Instructions ................. 5
Introduction .............. 7
Installation ................ 8
Selecting a Location ... 8
Connecting/Charging
the Battery Pack ....... 11
Operation ............... 13
Making and Receiving
Calls ........................ 13
Adjusting the Handset
Ringer and Earpiece
Volume ..................... 14
Redial ....................... 15
Tone Dialing
Switch-over ............... 15
Traveling
Out-of-Range ........... 15
Selecting a Different
Channel .................... 16
Page ......................... 16
Flash and Call
Waiting ..................... 16
Voice Mail Waiting
Indicator ................... 16
Setting Menu
Options ..................... 17
Area Code ................ 18
Steps for Entering
Names and Special
Characters ................ 22
(continued)
Ô NOTE Ô
You must not connect your
phone to:
•
•
•
coin-operated systems
party-line systems
most electronic key
telephone systems
WARNING: To reduce the risk of
fire or shock hazard, do not expose
this product to rain or moisture.
IMPORTANT
INFORMATION
This telephone has been tested and found
to comply with all applicable UL and FCC
standards.
FCC STATEMENT
Your telephone compiles with Part 68 of the
FCC Rules.Upon request, you must provide
the phone’s FCC registration number and
REN to your phone company. These
numbers are on the base unit.
Your phone is not intended to be used with
party-line systems. Connection to party line
service is subject to state tariffs. Contact the
state public utility commission, public
service commission, or corporation
commission for information. Ô
We have designed your phone to conform
to federal regulations, and you can connect
it to most telephone lines. However, each
phone (and each device, such as a
telephone or answering machine) that you
connect to the telephone line draws power
from the telephone line. We refer to this
power draw as the device’s ringer
CAUTION
The lightning symbol is intended to alert you to the presence of
uninsulated dangerous voltage within this product’s enclosure that
might be of sufficient magnitude to constitute a risk of electric shock.
Do not open the product’s case.
2
.
CAUTION: TO REDUCE THE RISK OF ELECTRIC
!
RISK OF ELECTRIC
SHOCK DO NOT OPEN
!
SHOCK, DO NOT REMOVE COVER OR BACK. NO USERSERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED PERSONNEL.
The exclamation symbol is intended to inform you that important operating
and maintenance instructions are included in the literature accompanying
this product.
43-3548.fm Page 3 Tuesday, February 25, 2003 1:06 PM
If you use more than one phone or other
device on the line, add up all of the RENs. If
the total is more than five (three in rural
areas), your telephones might not ring. If
ringer operation is impaired, remove a
device from the line.
In the unlikely event that your phone causes
problems on the phone line, the phone
company can temporarily discontinue your
service. If this happens, the phone company
attempts to notify you in advance. If
advance notice is not practical, the phone
company notifies you as soon as possible
and advises you of your right to file a
complaint with the FCC.
Also, the phone company can make
changes to its lines, equipment, operations,
or procedures that could affect the operation
of this phone. The telephone company
notifies you of these changes in advance, so
you can take the necessary steps to prevent
interruption of your telephone service.
SURGE PROECTION
CONTENTS
(continued)
Making Calls with
Memory Dialing ........ 23
Chain Dialing ........... 24
Editing a Stored Name
and/or Phone
Number .................... 24
Erasing a Stored Name
and Phone Number .. 26
Testing Stored
Emergency
Numbers .................. 27
One-touch speed
dial ........................... 27
Storing And Editing
The Speed Dial ........ 27
Making Calls with the
SPEED DIAL ............ 28
Deleting the SPEED
DIAL ......................... 28
Caller ID ................... 28
When the Telephone
Rings ........................ 29
Viewing the Caller ID
Message List ............ 30
Deleting Information
from the Caller ID
List ........................... 30
Using the Caller ID
List ........................... 31
Using a Headset .....
Troubleshooting ......
Care ........................
Service and Repair ..
Important Information
equivalence number, or REN on the back of
your phone.
33
34
35
35
Your telephone has built-in protection
circuits to reduce the risk of damage from
surges in telephone line and power line
current. These protection circuits meet or
exceed the FCC requirements. However,
lightning striking the telephone or power
lines can damage your telephone.
Lightning damage is not common.
Nevertheless, if you live in an area that has
severe electrical storms, we suggest that
you unplug your phone when storms
approach to reduce the possibility of
damage.
3
43-3548.fm Page 4 Tuesday, February 25, 2003 1:06 PM
IMPORTANT SAFETY INSTRUCTIONS
Important Safety Instructions
When using your telephone equipment, basic safety precautions should
always be followed to reduce the risk of fire, electric shock and injury to
persons, including the following:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the product.
3. Never install telephone wiring during a lightning storm.
4. Never install telephone jacks in wet locations unless the jack is
specifically designed for wet locations.
5. Never touch uninstalled telephone wires or terminals unless the
telephone line has been discon-nected at the network interface.
6. Use caution when installing or modifying telephone lines.
7. Do not fix the AC power supply cord to building surfaces with metal
fittings (if the product has an AC power cord).
8. Unplug this product from the wall outlet before cleaning. Do not use
liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
9. Do not use this product near water, for example, near a bathtub,
wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a
swimming pool.
10. Do not place this product on an unstable cart, stand, or table. The
product may fall, causing serious damage to the product.
11. Slots and openings in the cabinet and the back or bottom are
provided for ventilation. To protect it from overheating, these
openings must not be blocked or covered. The openings should
never be blocked by placing the product on a bed, sofa, rug, or other
similar surface. This product should never be placed near or over a
radiator or heat register. This product should not be placed in a builtin installation unless proper ventilation is provided.
12. This product should be operated only from the type of power source
indicated on the marking label. If you are not sure of the type of
power supply to your home, consult your local power company.
4
43-3548.fm Page 5 Tuesday, February 25, 2003 1:06 PM
14. Do not overload wall outlets and extension cords as this can result in
a risk of fire or electric shock.
15. Never push objects of any kind into this product through cabinet slots
as they may touch dangerous voltage points or short out parts that
could result in a risk of fire or electric shock. Never spill liquid of any
kind on the product.
16. To reduce the risk of electric shock, do not disassemble this product.
Take it to a qualified service technician when service or repair work
is required. Opening or removing covers may expose you to
dangerous voltage or other risks. Incorrect reassembly can cause
electric shock when the product is subsequently used.
17. Unplug this product from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
• When the power cord plug is damaged or frayed.
• If liquid has been spilled, into the product.
• If the product has been exposed to rain or water.
• If the product does not operate normally by following the
operating instructions. Adjust only those controls that are covered
by the operating instructions because improper adjustment of
other controls may result in damage and will often require
extensive work by a qualified technician to restore the product to
normal operation.
• If the product has been dropped or the cabinet has been
damaged.
• If the product exhibits a distinct change in performance.
18. Avoid using a telephone (other than a cordless type) during an
electrical storm. There may be a remote risk of electric shock from
lightning.
19. Do not use the telephone to report a gas leak in the vicinity of the leak.
BATTERY SAFETY INSTRUCTIONS
To reduce the risk of fire or injury, read and follow these instructions
5
Important Safety Instructions
13. Do not allow anything to rest on the power cord. Do not locate this
product where the cord will be stepped on.
43-3548.fm Page 6 Tuesday, February 25, 2003 1:06 PM
1. Use only the appropriate type and size battery pack specified in the
instruction manual provided for this product.
Important Safety Instructions
2. Do not dispose of the battery pack in a fire. The cell may explode.
Check with local codes for possible special disposal instructions.
3. Do not open or mutilate the battery pack. Released electrolyte is
corrosive and may cause damage to the eyes or skin. It may be toxic
if swallowed.
4. Exercise care in handling the battery pack in order not to short it with
conducting materials such as rings, bracelets, and keys. The battery
or conductor may overheat and cause burns.
5. Charge the battery pack provided or identified for use with this
product only in accordance with the instructions and limitations
specified in the instruction manual provided for this product.
6. Observe proper polarity orientation between the battery pack and
battery charger.
SAVE THESE INSTRUCTIONS
6
43-3548.fm Page 7 Tuesday, February 25, 2003 1:06 PM
INTRODUCTION
Thank you for purchasing a RadioShack 2.4
GHz Cordless Telephone. Your phone uses
advanced technology to give you superior
audio quality and extended range. The
phone’s Caller ID unit records each caller’s
telephone number (and name, if available in
your area) and the date and time of the call,
as provided by your local phone company to
Caller ID service subscribers. If you
subscribe to Call Waiting with Caller ID, the
phone shows you the incoming caller
information, even when you are already
talking on the phone.
! IMPORTANT !
•
When AC power is lost,
the phone loses the
security accessprotection code connection between the
base and the hand-set.
When power is restored,
put the handset on the
base briefly to restore
this connection so you
can use the handset.
•
Your phone operates on
standard radio
frequencies as allocated
by the FCC.
•
It is possible for other
radio units operating
nearby on similar
frequencies to
unintentionally intercept
your conversation or
cause interference. This
possible lack of privacy
can occur with any
cordless phone.
7
Introduction
Cordless phones require AC power to
operate. When the power is off, you cannot
make or receive calls using your phone.
You should also have a phone that does not
need AC power to operate (not a cordless
phone), so you can still make and receive
calls if there is an AC power failure. !
43-3548.fm Page 8 Tuesday, February 25, 2003 1:06 PM
CAUTION
You must use
a Class 2
power source
that supplies 9V DC and
delivers at least 210 mA.
Its center tip must be set
to positive and its plug
must fit the phone's DC
IN 9V jack. The supplied
adapter meets these
specifications. Using an
adapter that does not
meet these
specifications could
damage the phone or
the adapter.
Before using your phone, carefully peel the
protective film off the display. The film
protects the handset window during
shipment and is not necessary for use.
Always connect the AC
adapter to the phone
before you connect it to
AC power. When you
finish, disconnect the
adapter from AC power
before you disconnect it
from the phone.
• away from electrical machinery,
electrical appliances, metal walls or
filing cabinets, wireless intercoms,
alarms, and room monitors
!
•
Ô NOTE Ô
Installation
• If your home has
specially wired alarm
equipment connected to
the telephone line, be
sure that installing the
system does not disable
your alarm equipment.
If you have questions
about what will disable
alarm equipment,
contact your telephone
company or a qualified
installer.
• The USOC number of
the jack to be installed is
RJ11C (or RJ11W for a
wall plate jack).
8
INSTALLATION
SELECTING A LOCATION
You can place the phone’s base on a desk
or table, or mount it on a standard wall plate
or directly on a wall. Select a location that
is:Ô
• near an accessible AC outlet
• near a telephone line jack
• out of the way of normal activities
• away from other cordless phones
The base’s location affects the handset’s
range. If you have a choice of several
locations, try each to see which provides the
best performance.
Your telephone connects directly to a
modular telephone line jack. If your
telephone wiring does not have a modular
jack, you can update the wiring yourself
using jacks and adapters (available at your
local RadioShack store), or have the
telephone company update the wiring for
you. You must use compatible modular
jacks that are compliant with Part 68 of FCC
Rules. Ô
43-3548.fm Page 9 Tuesday, February 25, 2003 1:06 PM
On a Desk Top
1. Plug one end of
the supplied long
modular cord into
the TEL LINE jack
on the back of
the base.
2. Plug the modular
cord’s other end
into a modular
phone line jack.
TEL
3. Insert the
DC IN 9V LINE
supplied AC
adapter’s barrel plug into the DC IN 9V
jack on the back of the base.
4. Route the adapter’s cord through the
strain relief slot on the base, then plug
the adapter into a standard AC outlet.
5. Lift the base’s antenna to a vertical
position.
On a Wall Plate
1. Plug one end of the supplied short
modular cord into the TEL LINE jack on
the back of the base. Then insert the
supplied AC adapter’s barrel plug into
the DC IN 9V jack on the back of the
base.
Installation
2. Route the adapter and modular cords
through the grooves on the bottom of
the base.
3. Plug the short modular cord into the
wall plate jack, then align the base’s
keyhole slots with the wall plate studs
and slide the base down to secure it.
9
43-3548.fm Page 10 Tuesday, February 25, 2003 1:06 PM
4. Plug the adapter into a standard AC
outlet.
5. Lift the base’s antenna to a vertical
position.
On a Wall
To mount the phone directly on a wall, you
need two screws (not supplied) with heads
that fit into the keyhole slots on the bottom
of the base.
1. Drill two holes 315/16 inches (100 mm)
apart. Then thread a screw into each
hole, letting the heads extend about 1/8
inch (3 mm) from the wall.
2. Plug one end of the supplied long
modular cord into the TEL LINE jack on
the back of the base.
3. Insert the supplied AC adapter’s barrel
plug into the DC IN 9V jack on the back
of the base.
4. Route the adapter and modular cords
through the grooves on the bottom of
the base.
5. Align the base’s keyhole slots with the
mounting screws and slide the base
downward to secure it.
Installation
6. Plug the modular cord’s other end into
the phone jack, and plug the adapter
into a standard AC outlet.
7. Lift the base’s antenna to a vertical
position.
10
43-3548.fm Page 11 Tuesday, February 25, 2003 1:06 PM
The phone comes with a rechargeable
nickel-cadmium battery pack in the handset,
but not connected. Before using your
phone, you must connect the battery pack,
then charge it for about 15–20 hours. !
1. Press down and slide off the battery
compartment cover.
2. Lift the battery pack out of the
compartment.
3. Plug the battery pack’s connector into
the socket in the compartment (the
connector fits only one way), then place
the battery pack in the compartment.
4. Replace the cover.
To charge the battery pack, place the
handset on the base. The CHARGE/IN USE
indicator on the base lights and Total:00
appears on the handset display.
Recharge the battery pack when Low
Battery flashes on the display.
If you have trouble replacing the battery
pack, take the phone to your local
RadioShack for assistance.
!
o
Recharging the Battery Pack
• When you first use the phone after
charging or recharging the battery
pack, the phone might not work and
you might hear an error tone when you
press TALK. While holding PAGE, return
the handset to the base for about 3
seconds to change the security accessprotection code.
! IMPORTANT !
The EPA
certified
RBRC®
Battery
Recycling
Seal on the nickelcadmium (Ni-Cd) battery
indicates RadioShack is
voluntarily participating in
an industry program to
collect and recycle these
batteries at the end of their
useful life, when taken out
of service in the United
States or Canada. The
RBRC program provides a
convenient alternative to
placing used Ni-Cd
batteries into the trash or
the municipal waste
stream, which may be
illegal in your area. Please
call 1-800-THE-SHACK (1800-843-7422) for
information on Ni-Cd
battery recycling and
disposal bans/restrictions
in your area. RadioShack’s
involvement in this
program is part of the
company’s commitment to
preserving our
environment and
conserving our natural
resources.
o
WARNING
o
Dispose of the old battery
pack promptly and properly.
Do not burn or bury it. See
“Battery Safety Instructions”
on Page 5 for additional
information on proper
battery handling.
11
Installation
CONNECTING/CHARGING THE
BATTERY PACK
43-3548.fm Page 12 Tuesday, February 25, 2003 1:06 PM
! IMPORTANT !
Be sure the battery pack is
properly connected before
you try to charge it. The
CHARGE/IN USE indicator
lights when the handset is
on the base, even if the
battery pack is not
connected.
• If the base loses power for about an
hour while the handset is away from it,
the security access-protection code
might be lost. To change the code,
while holding PAGE, return the handset
to the base for about 3 seconds.
• If the battery pack becomes weak
during a call, the handset beeps every
3 seconds and Low Battery flashes.
When this happens, you cannot make a
call until you recharge the battery
pack.!
• If the display is blank and the phone
does not work, recharge the battery
pack. (The battery power might be too
low to light the display.)
• About once a month, fully discharge the
battery by keeping the handset off the
base until Low Battery flashes on
the display. Otherwise, the battery pack
loses its ability to fully recharge.
• The handset loses its security accessprotection code if the battery pack is
completely discharged. While holding
PAGE, place the handset on the base to
recharge the battery pack and change
the code.
• Using a pencil eraser, clean the
charging contacts on the handset and
base about once a month.
Installation
• If you are not going to use your phone
for an extended period, disconnect the
battery pack. This increases the battery
pack’s usable life.
12
43-3548.fm Page 13 Tuesday, February 25, 2003 1:06 PM
• The supplied battery pack should last
for about a year. If the battery pack
does not hold a charge for more than 2
hours after an overnight charge,
replace it with a new 3.6-volt, 600 mAh
battery pack with a connector that fits
the socket in the battery compartment.
You can order a replacement battery
pack through RadioShack. Install the
new battery pack and charge it for
about 15–20 hours.
OPERATION
MAKING AND RECEIVING
CALLS
Handset Off Base
Pick up the handset
To
(Auto Talk) Ô or
answer pick up the handset
a call and press talk/
FLASH.
1)Pick up the
handset.
2)Press talk/
FLASH.
3)Listen for the dial
To
tone.
make 4)Dial the number.
a call OR
1)Pick up the
handset.
2)Dial the number,
then press talk/
FLASH.
Press talk/FLASH,
any number, /
f or #/g
g keys
tone/f
(Auto Talk).
1)Press talk/
FLASH.
2)Listen for the dial
tone.
3)Dial the number.
OR
Dial the number,
then press talk/
FLASH.
Ô NOTE Ô
Refer to page 17 “Setting
Menu Options” to turn On
the Auto Talk feature if
desired.
Operation
Action Handset On Base
13
43-3548.fm Page 14 Tuesday, February 25, 2003 1:06 PM
Action Handset On Base
Handset Off Base
To
hang
up
Press end or return the handset to the
base (Auto Standby).
To
redial
1)Pick up the
handset.
2)Press talk/
FLASH.
3)Listen for the dial
tone.
4)Press REDIAL/
PAUSE.
OR
1)Pick up the
handset.
2)Press REDIAL/
PAUSE, then
press talk/
FLASH.
1)Press talk/
FLASH.
2)Listen for the dial
tone.
3)Press REDIAL/
PAUSE.
OR
Press REDIAL/
PAUSE, then press
talk/FLASH.
ADJUSTING THE HANDSET
RINGER AND EARPIECE
VOLUME
Handset ringer tone and volume
Press the volume up key or volume down
key (labeled as, VOL e or VOL d keys) in
standby mode to select one of five ringer
tones and volume combinations. Ring
Type A High, Ring Type A Low, Ring
Type B High, Ring Type B Low, or
Ringer Off.
Operation
Ô NOTE Ô
When you press volume up
key (VOL e) in Maximum
mode or volume down key
(VOL d) in Low mode, an
error tone sounds.
14
Earpiece volume
Pressing the volume up key or volume down
key (labeled as, VOL e or VOL d keys)
during a call will change the earpiece
volume of the handset. This setting will
remain in effect after the telephone call has
ended. Ô
43-3548.fm Page 15 Tuesday, February 25, 2003 1:06 PM
Temporarily Mute Ringer
If the handset is off the base, simply press
the end key to temporarily mute the
incoming ring. The ringer will sound with the
next incoming call.
REDIAL
The REDIAL/PAUSE key redials the last
number dialed. The redialed number can be
up to 32 digits long.
TONE DIALING SWITCH-OVER
Some telephone companies use equipment
that requires pulse dialing (sometimes
referred to as rotary dialing).
If you need to enter tone dialing digits, you
can switch-over to tone dialing during the
call. For example, entering your bank
account number after you have called your
bank. Ô
Initially make your call with the pulse dialing
mode. Once your call connects, press the
f key. Enter the desired number.
/tone/f
These digits will be sent as tone dialing.
Once the call ends, the tone mode is
canceled and pulse dialing mode resumes.
Ô NOTE Ô
• The tone feature only
applies when the dial
mode is set to pulse.
•
This special number can
be stored in a memory
location. This is referred
to as Chain Dialing (See
page 24.)
TRAVELING OUT-OF-RANGE
Operation
During a call, as you begin to move your
handset too far from your base unit, noise
increases. If you pass the range limits of the
base unit, your call will terminate within 1
minute.
15
43-3548.fm Page 16 Tuesday, February 25, 2003 1:06 PM
SELECTING A DIFFERENT
CHANNEL
If you encounter interference while using
your phone, you can manually change the
phone´s channel for clear operation. This
function works only when the phone is in
use. Press DELETE/CHANNEL. ¨Scanning¨
appears on the display, indicating the phone
is changing to another channel.
Ô NOTE Ô
Page
You can cancel paging by
pressing the PAGE key on
the base.
Flash and Call Waiting
You must subscribe through
your local telephone
company to receive Call
Waiting Service.
Voice Mail Waiting
Indicator
You must subscribe to
voice mail service from your
telephone company in order
to use this feature. The
voice mail company will
provide you with the access
number.
PAGE
To locate the handset (while it’s off the
base), press PAGE on the base. The
handset beeps for 60 seconds. Paging is
canceled when pressing any key or the
handset is returned to the base. Ô
FLASH AND CALL WAITING
If you have “Call Waiting” service and a call
waiting tone sounds while you are on a call,
press talk/FLASH to accept the waiting call.
There is a short pause, then you will hear
the new caller. To return to the original
caller, press talk/FLASH again.Ô
VOICE MAIL WAITING
INDICATOR
Operation
If you subscribe to voice mail service, you
can use your cordless telephone to access
your voice mailbox. The CHARGE/IN USE
light on the base of your phone flashes
whenever you have messages waiting in
your voice mailbox. Just program the
SPEED DIAL key with your access number
and you can get your messages at the
touch of a button. (The voice mail service
provider will supply you with the access
number. This number may be simply a
phone number. Refer to the provider’s
literature.)Ô
16
43-3548.fm Page 17 Tuesday, February 25, 2003 1:06 PM
You may need to occasionally reset the
indicator if it remains On after you have
retrieved your messages. To reset the
indicator, press and hold PAGE for 5 second.
SETTING MENU OPTIONS
There are five setup options available. They
are Caller ID options [Auto Talk, CIDCW
(Caller ID on Call Waiting), Area Code], Dial
Mode and Language.
Auto Talk
Auto Talk allows you to answer the phone
without pressing the talk/FLASH button.
If the phone rings when Auto Talk is On,
simply remove the handset from the base
and the phone automatically answers the
call. If the phone rings when Auto Talk is
Off, you must press talk/FLASH to answer
the call. Ô
Caller ID options
To change your Auto Talk and CIDCW:
1. Press and hold CID/MENU.
2. Use VOL e or VOL d keys to move the
pointer to the selection that you would
like to change. Press SELECT to toggle
between ¨On¨ and ¨Off¨ for Auto Talk
and CIDCW.
Ô NOTE Ô
•
The Cordless phone
features include Auto
Talk and Auto Standby.
Auto Talk allows you to
answer a call by just
removing the handset
from the base so you
don’t have to waste time
pushing buttons. Auto
Standby allows you to
hang up by simply
returning the handset to
the base.
Operation
3. Press end and return the handset to the
base unit to complete the setting. The
handset returns to the standby mode.
17
43-3548.fm Page 18 Tuesday, February 25, 2003 1:06 PM
Ô NOTE Ô
Area Code
• If your calling area
requires 10-digit dialing,
do not program this
option.
•
•
When the area code
has already been stored
in memory, the stored
area code will be
displayed. To change it,
use the DELETE/
CHANNEL and number
keys to enter the new
area code.
Then press SELECT. A
confirmation tone
sounds. To complete
the setting, press end
or return the handset to
the base unit.
Choosing the dialing
mode
Make sure your battery
pack is fully charged
before choosing the dialing
mode.
AREA CODE
If you enter a 3-digit area code number in
the Area Code option, your local area code
does not appear in Caller ID messages. Do
not program this option, if your calling area
requires 10-digit dialing. When reviewing
Caller ID messages, you will see only the
local seven digit number. For calls received
from outside your local area code, you will
see a full 10-digit number.
1. When the phone is in the standby
mode, press and hold CID/MENU. The
Caller ID setting screen appears.
2. Press VOL d key twice to select ¨Area
Code¨.
3. Press SELECT.
4. Use the number keys (0 - 9), or
DELETE/CHANNEL to enter the 3-digit
area code.
5. Press SELECT. A confirmation tone
sounds and the displayed area code is
entered.
6. Press end or return the handset to the
base unit to complete the setting. The
handset returns to the standby mode.Ô
Choosing the dialing mode
Operation
Most phone systems use tone dialing which
sends DTMF tones through the phone lines.
However some phone systems still use
pulse dialing such as in rural areas. Ô
The default setting is tone dialing.
Depending on your dialing system, set the
mode as follows:
18
43-3548.fm Page 19 Tuesday, February 25, 2003 1:06 PM
1. When the phone is in the standby
mode, press and hold CID/MENU.
2. Press VOL d key three times to select
¨Dial¨.
3. Press SELECT to toggle between
¨Tone¨ and ¨Pulse¨ for each setting.
4. Press end or return the handset to the
base unit to complete the setting. The
handset returns to the standby mode.
• If you are not sure of your dialing
system, set for tone dialing. Make a
trial call.
If the call connects, leave the setting
as is, otherwise set for pulse dialing.
• If your phone system requires pulse
dialing and you need to send the
DTMF tones for certain situations
during a call, you may “switch-over”
to tone dialing. (Refer to “Tone
Dialing Switch-over” on page 15.)
Setting the language
1. When the phone is in the standby
mode, press and hold CID/MENU.
2. Press VOL d key four times to select
¨Language¨.
Operation
3. Press SELECT to toggle between ¨Eng¨
and ¨Esp¨ for each setting.
4. Press end or return the handset to the
base unit to complete the setting. The
handset returns to the standby mode.
19
43-3548.fm Page 20 Tuesday, February 25, 2003 1:06 PM
Ô NOTE Ô
In memory dialing
operation, you must press
a key within 30 seconds or
the phone will return to the
standby mode. If you
return the handset to the
base, the phone will return
to the standby mode also.
Storing Phone Numbers and
Names
Memory Dialing allows you to dial a number
using just a few key presses. Your cordless
telephone stores up to 20 names/numbers
in the handset. Ô
1. Press MEM, ¨Select Memory¨ is
displayed.
2. Press VOL e or VOL d keys, or enter a
number (01 - 20) to select the memory
location where you would like to store
the number.
3. Press MEM or SELECT.
4. Press MEM or SELECT. A cursor flashes
indicating that the display is ready for
the name to be entered.
If “Edit Memory X X” appears, the
selected memory location is already
stored. Then you must either edit the
entry in this location, delete the entry in
this location, or select ¨Go Back¨ to
choose another location.
5. To enter a name (up to 13 characters),
use the number keys.
• See the “Steps for entering names
and special characters”. (See
page 22).
Operation
g and /tone/f
f keys to move
• Use #/g
the cursor to the desired location.
• Use DELETE/CHANNEL to delete
characters as needed.
• Press and hold DELETE/CHANNEL to
delete all the characters.
20
43-3548.fm Page 21 Tuesday, February 25, 2003 1:06 PM
• If a name is not required, go to step
6.
Operation
6. Press MEM or SELECT. ¨Store
Number¨ is displayed.
The cursor flashes indicating that the
display is ready for the number to be
entered.
7. Use the number keys to enter the
phone number.
• The phone number cannot exceed
20 digits.
• Use REDIAL/PAUSE to enter a pause
in the dialing sequence. The display
shows a ¨P¨. Each pause counts as
one digit and represents a two
second delay of time between the
digits. Ô
• Use DELETE/CHANNEL to delete
digits as needed.
8. Press MEM or SELECT. You will hear a
confirmation tone. Ô
Ô NOTE Ô
Storing Phone Numbers
and Names
The pause feature is useful
for long distance calling,
credit card dialing, or
sequences that require a
pause between digits.
Memory storage is complete.
For example, if you store a name and
number into memory location number
01, the display shows ¨Memory01
Stored¨.
Repeat steps 2 - 8 to store more
numbers.
9. Press end to return to the standby
mode.
21
43-3548.fm Page 22 Tuesday, February 25, 2003 1:06 PM
Ô NOTE Ô
Operation
Steps for Entering
Names and Special
Characters
If the next character uses
the same number key, you
g to move the
must press #/g
cursor over. Otherwise the
next time you press the
number key, it changes the
character that was
previously set.
STEPS FOR ENTERING NAMES
AND SPECIAL CHARACTERS
Refer to the letters on the number keys to
select the desired characters.
With each press of a numeric key, the
displayed character appears in the following
order: Upper case letters first, lower case
letters next and finally the number
corresponding to the key. Ô
For example, to enter Movies.
1. Pick up the handset. Press MEM.
2. Enter a number or press VOL e or VOL
d keys to select a memory location.
3. Press MEM or SELECT.
4. Press MEM or SELECT. (When there is
information already stored in the
selected memory location, ¨Edit
MemoryXX¨ is displayed. See page 24
for information on “Editing a Stored
Name and/or Phone Number”.)
g to move the
5. Press 6 then press #/g
cursor to the right.
6. Press 6 six times.
7. Press 8 six times.
8. Press 4 six times.
22
43-3548.fm Page 23 Tuesday, February 25, 2003 1:06 PM
9. Press 3 five times.
10. Press 7 eight times.
11. When finished, press MEM or SELECT.
Operation
To continue to store the telephone number,
proceed to step 7 on page 21.
If you make a mistake while
entering a name
f or #/g
g keys to move the cursor
Use /tone/f
to the incorrect character.
Press DELETE/CHANNEL to erase the wrong
character, then enter the correct character.
To delete all characters, press and hold
DELETE/CHANNEL.
MAKING CALLS WITH
MEMORY DIALING
Memory dialing from Standby
Mode
1. Press MEM. The handset displays your
programmed memory locations.
2. Press VOL e or VOL d keys, or enter the
number (01 - 20) to select the memory
location you would like to dial. Ô
3. Press talk/FLASH. ¨Talk¨ and the
volume setting appear on the display.
Then the displayed number is dialed. Ô
Ô NOTE Ô
Memory dialing from
Standby Mode
• If you press SELECT
before talk/FLASH, you
can confirm the name
and the number stored
in the selected memory
location.
•
To exit the memory
function without dialing,
press end. The handset
returns to the standby
mode.
•
Whenever you are
using a memory menu
screen, you must press
a key within 30 seconds
or the phone will return
to the standby mode.
Memory dialing from Talk Mode
1. Press talk/FLASH. ¨Talk¨ and the
volume setting appears.
2. Press MEM.
23
43-3548.fm Page 24 Tuesday, February 25, 2003 1:06 PM
Ô NOTE Ô
Memory dialing from Talk
Mode
If you select a memory
location that does not have
a stored number, the
phone will not dial.
3. Press VOL e or VOL d keys, or enter a
number (01 - 20) to select the memory
location of the desired phone number.
The selected name is displayed. Ô
4. The phone number in the memory will
be dialed when the SELECT key is
pressed.
5. To hang up, press end.
CHAIN DIALING
The memory locations on the handset are
not limited to phone numbers. You can also
store a group of numbers (up to 20 digits)
that you need to enter once your call
connects. This is referred to as Chain
Dialing.
Operation
An example of this is a bank account
number. Once you have called your bank,
and are prompted to enter the account
number, press MEM and select the location
number where the special number has been
stored, then press SELECT.
Store your special number with an
identifying name. (Refer to “Storing Phone
Numbers and Names” on page 20.)
EDITING A STORED NAME
AND/OR PHONE NUMBER
1. Press MEM, ¨Select Memory¨ is
displayed.
2. Press VOL e or VOL d keys, or enter a
number (01 - 20) to select the memory
location you would like to edit, and
press MEM or SELECT.
24
43-3548.fm Page 25 Tuesday, February 25, 2003 1:06 PM
3. Press MEM or SELECT. The screen
appears with the memory location
number that you have selected in the
display.
4. Press VOL e or VOL d keys to select
¨Edit MemoryXX¨, then press MEM or
SELECT. The cursor flashes indicating
that the display is ready for the name to
be edited. When a name has not been
stored, the cursor appears at the
beginning of the second line.
f, #/g
g
5. Use the number keys, /tone/f
keys, or DELETE/CHANNEL to edit the
name. (See page 22.) To edit only the
phone number, skip this step.
6. Press MEM or SELECT. The cursor
flashes indicating that the display is
ready for the number to be edited.
7. Use the number key, REDIAL/PAUSE or
DELETE/CHANNEL to edit the phone
number. The phone number cannot
exceed 20 digits. (See page 24.)
If you don´t want to change the phone
number, skip this step.
Operation
8. Press MEM or SELECT. If you changed
either name or phone number, a
confirmation display shows up. If it is
correct, press VOL e key to select “Yes”
and press SELECT. You hear a
confirmation tone. The memory storage
is complete.
For example, if you store a name and
number into memory location number
01, the display shows ¨Memory01
Stored¨. After about 2 seconds,
Select Memory Screen is displayed.
25
43-3548.fm Page 26 Tuesday, February 25, 2003 1:06 PM
9. Press end to return to the standby
mode.
Operation
ERASING A STORED NAME
AND PHONE NUMBER
1. Press MEM, ¨Select Memory¨ is
displayed.
2. Press VOL e or VOL d keys, or enter a
number (01 - 20) to select the memory
location you would like to erase.
3. Press MEM or SELECT.
The screen appears with the memory
location number that you have selected
in the display.
4. Press MEM or SELECT.
5. Press VOL d key to move the pointer
down to ¨Delete MemoryXX¨.
6. Press MEM or SELECT. The
confirmation screen appears.
7. Press VOL e key to move the pointer to
¨Yes¨.
8. Press SELECT or DELETE/CHANNEL.
You hear a confirmation tone.
9. After about 2 seconds, the display
returns to the Select memory screen.
You may delete the information in
another memory location (return to step
2) or press end to return to the standby
mode.
26
43-3548.fm Page 27 Tuesday, February 25, 2003 1:06 PM
TESTING STORED EMERGENCY
NUMBERS
Operation
If you store an emergency service’s number
(police department, fire department,
ambulance) and you choose to test the
stored number, make the test call during the
late evening or early morning hours to avoid
peak demand periods. Also, remain on the
line to explain the reason for your call.
ONE-TOUCH SPEED DIAL
You can store your most frequently dialed
number in the SPEED DIAL location. The
One-touch speed dial allows you to dial a
number with one key press. (There is no
need to press talk/FLASH. The phone will
automatically dial the number stored.)
STORING AND EDITING THE
SPEED DIAL
1. When the phone is in the standby
mode, press and hold SPEED DIAL.
If “Edit Number” appears, there is a
number already stored. Press VOL e or
VOL d keys to select ¨Edit Number¨,
then press SELECT.
2. Store the number by following step 7
under “Storing Phone Numbers and
Names” on page 21.
3. Press SELECT.
You hear a confirmation tone. Memory
storage is complete.
27
43-3548.fm Page 28 Tuesday, February 25, 2003 1:06 PM
Ô NOTE Ô
Operation
•
Number stored in
SPEED DIAL is
independent from the
numbers stored in
Memory Dial.
•
If the SPEED DIAL
does not have a stored
number, the handset
will beep rapidly and the
phone will not dial.
MAKING CALLS WITH THE
SPEED DIAL
When the phone is in the standby mode,
simply press SPEED DIAL. The number
stored in the SPEED DIAL memory location
is instantly dialed. Ô
DELETING THE SPEED DIAL
1. When the phone is in the standby
mode, press and hold SPEED DIAL.
2. Press VOL e or VOL d keys to select
¨Delete Number¨.
3. Press SELECT.
4. Press VOL e key to move the pointer to
¨Yes¨.
5. Press SELECT or DELETE/CHANNEL.
You hear a confirmation tone. After
about 2 seconds, the handset returns
to the standby mode.
CALLER ID
You must subscribe to Caller ID service
to use this feature.
When the telephone rings, the Caller ID
feature allows you to view the caller´s name
and phone number on the display before
you answer the phone. The handset
displays the phone number of the incoming
call, the name, and time. Additionally, you
can dial the displayed number and store the
information for memory dialing. Make sure
you have turned on the Caller ID/Call
Waiting feature. (See page 17.)
28
43-3548.fm Page 29 Tuesday, February 25, 2003 1:06 PM
WHEN THE TELEPHONE RINGS
Ô NOTE Ô
•
If you answer a call
before the Caller ID
message is received
(Example: before the
second ring), the Caller
ID message will not
appear.
•
When the call is
received via a
telephone company that
does not offer Caller ID
service, the caller´s
phone number and
name do not appear.
(This includes
international calls.)
•
When the call is via a
private branch
exchange (PBX), the
caller´s phone number
and name may not
appear.
•
Data errors appear as
¨ ¨.
You may receive any one of the
following messages:
When invalid data is
received
“Incomplete Data”
When a private name “Private Name”
is received
When a private
number is received
“Private Number”
When a unknown
name is received
“Unknown Name”
When a unknown
number is received
“Unknown Number”
2. When you pick up the phone, the
display changes to ¨Talk¨. (Auto Talk
feature is set to on.)
29
Operation
1. When the Caller ID message is
received, the display shows the caller´s
phone number along with the date and
time. The incoming call information is
stored in the Caller ID record. If the
Caller ID service includes the caller´s
name, the caller´s name appears on
the display (up to 15 letters).Ô
43-3548.fm Page 30 Tuesday, February 25, 2003 1:06 PM
Ô NOTE Ô
Operation
Viewing the Caller ID
Message List
• In Caller ID operation, if
no key is pressed for
more than 30 seconds,
an error tone sounds
and the telephone
returns to the standby
mode.
• If a call comes in via a
telephone system that
does not offer Caller ID
service, no information
is stored.
• Each message can be
up to 15 characters for
the phone number and
the name.
• The number of calls
from the same Caller ID
appears next to the
received time. Once
you view the new
message, the number
will disappear.
Deleting a Caller ID
message
While using the ¨Delete
All?¨ or ¨Delete
Message?¨ screen if no
key is pressed for more
than 30 seconds, an error
tone sounds and the
telephone returns to the
standby mode.
VIEWING THE CALLER ID
MESSAGE LIST
The Caller ID list stores information for up to
30 incoming calls - even unanswered calls.
Ô
1. Press CID/MENU.
The summary screen appears. The
screen shows the number of new
messages and total messages.
2. Press VOL d key to display the latest
Caller ID message.
3. Press VOL d key to see the next
message. Or press VOL e key to see
the previous message.
4. Press end to return to the standby
mode.
DELETING INFORMATION
FROM THE CALLER ID LIST
The cordless phone stores up to 30
messages. If the phone receives the 31st
message, the oldest one in the list is
automatically deleted and the newest is
stored. Caller ID data can also be deleted
manually.
Deleting a Caller ID message
1. Press CID/MENU. Display the message
to be deleted from the Caller ID list by
pressing VOL e or VOL d keys. Ô
2. Press DELETE/CHANNEL.
3. Press VOL e or VOL d keys to select
¨Yes¨ or ¨No¨.Ô
4. Press SELECT or DELETE/CHANNEL.
30
43-3548.fm Page 31 Tuesday, February 25, 2003 1:06 PM
When the pointer is at ¨No¨:
The display returns to the Caller ID
message.
Deleting all Caller ID names/
numbers Ô
1. Press CID/MENU.
2. Press DELETE/CHANNEL.
3. Press VOL e or VOL d keys to select
¨Yes¨ or ¨No¨.
4. Press SELECT or DELETE/CHANNEL.
When the pointer is at ¨Yes¨:
A tone sounds and all stored Caller ID
messages are deleted.
When the pointer is at ¨No¨:
The display returns to the summary
screen.
USING THE CALLER ID LIST
Ô NOTE Ô
Deleting a Caller ID
message
If you get an incoming call
or page, the deleting
operation is canceled and
the telephone returns to
the standby mode so you
can answer the call or
page.
Deleting all Caller ID
names/numbers
You cannot make a call
from the Caller ID list if
your cordless telephone is
connected to a private
branch exchange (PBX).
Calling a party from the
Caller ID list
You can place a call from
talk mode.
Press talk/FLASH, then
press CID/MENU.
Select the phone number
that you want to dial by
pressing the VOL e or VOL
d key. Press SELECT.
The displayed phone
number will be dialed.
Calling a party from the Caller
ID list
You can place a call from the Caller ID list.
The cordless phone stores up to 30
messages.Ô
1. Press CID/MENU. Select the phone
number that you want to dial by
pressing VOL e or VOL d keys.
2. Press talk/FLASH. The displayed phone
number dials automatically.
31
Operation
When the pointer is at ¨Yes¨:
A tone sounds and the Caller ID
message is deleted. The next Caller ID
message is then displayed.
43-3548.fm Page 32 Tuesday, February 25, 2003 1:06 PM
Long Distance calls and Area
Code Setting/Cancellation
Ô NOTE Ô
Long Distance calls and
Area Code Setting/
Cancellation
When a long distance call
has been set, ¨1¨ appears
in the display.
Storing Caller ID
Messages in Memory
dialog
• You cannot store a
Caller ID message if no
phone number appears
in the message.
Operation
• If a message has
already been stored in
the selected memory
number location, a
confirmation screen is
displayed.
Press VOL e key to
select ¨Yes¨. Press
SELECT to overwrite.
The display returns to
the Caller ID list.
Pressing 1 while the incoming Caller ID
information is displayed (in step 1) will place
the prefix ¨1¨ in the display to set up for a
long distance call. Pressing 3 will set or
cancel an area code setting. Ô
Storing Caller ID messages in
Memory dialing
Messages shown in the Caller ID list can be
stored in memory dialing. Using the
incoming call information (i.e., Caller ID list),
the phone number of the party on the Caller
ID list can be stored in memory.Ô
1. Press CID/MENU.
Select the phone number to be stored
from the Caller ID list by pressing VOL
e or VOL d keys.
2. Press MEM.
3. Press VOL e or VOL d keys or enter a
number (01 - 20) to select the memory
location to be stored. Ô
4. Press SELECT.
You hear a confirmation tone, and the
number is stored in memory. The
display returns to the Caller ID list.
32
43-3548.fm Page 33 Tuesday, February 25, 2003 1:06 PM
USING A HEADSET
You can make or answer calls with handsfree convenience using an optional headset
that has a 3/32-inch (2.5-mm) plug.
RadioShack has a variety of headsets
available.
Ô NOTE Ô
•
If you place the handset
on the base to recharge
it while the headset is
corrected, be sure the
handset seats propely.
•
You can use a handset
holder (available from
your local RadioShack
store) to hang the
handset on your belt for
greater convenience
when using a headset.
Connecting a headset disconnects the
handset’s earpiece and microphone.
e or d on the handset also controls the
headset’s volume.
With a headset connected, you can make or
answer calls as usual using the keys on the
handset.
When you finish using the headset,
disconnect it from the handset and close the
rubber cover to protect the jack.
33
Using a Headset
To connect the headset, gently flip open the
rubber headset jack cover on the side of the
handset, then insert the headset’s plug into
the jack. Ô
43-3548.fm Page 34 Tuesday, February 25, 2003 1:06 PM
TROUBLESHOOTING
If your phone is not performing to your expectations, please try these
simple steps first
Problem
Solution
Troubleshooting
• Make sure the AC adapter is plugged into the
The CHARGE/IN USE LED
base and wall outlet.
won’t illuminate when the
• Make sure the handset is properly seated in the
handset is placed in the
base.
base.
• Make sure the charging contacts on the handset
and base are clean.
• Make sure that the base antenna is in a vertical
position.
• Move the handset and/or base to a different
location away from metal objects or appliances
The audio sounds weak
and try again.
and/or scratchy.
• Press DELETE/CHANNEL to help eliminate
background noise.
• Make sure that you are not too far from the
base.
• Check both ends of the base telephone line
cord.
• Make sure the AC adapter is plugged into the
base and wall outlet.
Can’t make or receive calls. • Disconnect the AC adapter for a few minutes,
then reconnect it.
• Change the digital security code (see page 11).
• Make sure that you are not too far from the
base.
• The battery pack may be weak. Charge the
battery for 15-20 hours.
• The handset may be too far away from the base
The handset doesn’t ring or
unit.
receive a page.
• Place the base unit away from appliances or
metal objects.
• Change the digital security code (see page 11).
• Keep the handset away from microwave ovens,
computers, remote control toys, wireless
microphones, alarm systems, intercoms, room
Severe noise interference.
monitors, fluorescent lights, and electrical
appliances.
• Move to another location or turn off the source
of interference.
34
43-3548.fm Page 35 Tuesday, February 25, 2003 1:06 PM
Problem
The Caller ID does not
display.
Voice Message Indication
does not work.
Solution
• The handset was picked up before the second
ring.
• The call was placed through a switchboard.
• Call your local telephone company to verify your
Caller ID service is current.
• Charge the handset.
• Contact your local telephone company to make
sure that your telephone receives FSK message
signaling.
If you still have problems, disconnect the
phone. If other phones on the same line
work properly, the fault is in this phone or its
installation. If you cannot find the problem,
take the phone to your local RadioShack
store for assistance.
CARE
Keep the phone dry; if it gets wet, wipe it dry
immediately. Use and store the phone only
in normal temperature environments.
Handle the phone carefully; do not drop it.
Keep the phone away from dust and dirt,
and wipe it with a damp cloth occasionally
to keep it looking new.
SERVICE AND REPAIR
Care
If your phone is not performing as it should,
take it to your local RadioShack store for
assistance. Modifying or tampering with the
phone’s internal components can cause a
malfunction and might invalidate its
warranty and void your FCC authorization to
operate it.
35
43-3548.fm Page 36 Tuesday, February 25, 2003 1:06 PM
Limited One-Year Warranty
This product is warranted by RadioShack against manufacturing defects in material and
workmanship under normal use for one (1) year from the date of purchase from RadioShack
company-owned stores and authorized RadioShack franchisees and dealers. EXCEPT AS
PROVIDED HEREIN, RadioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE DURATION OF THE
WRITTEN LIMITED WARRANTIES CONTAINED HEREIN. EXCEPT AS PROVIDED
HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO CUSTOMER
OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS OR
DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFORMANCE OF THE
PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, INCLUDING, BUT
NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS OF
TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED
OF THE POSSIBILITY OF SUCH DAMAGES.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or
limitation of incidental or consequential damages, so the above limitations or exclusions may
not apply to you.
In the event of a product defect during the warranty period, take the product and the RadioShack sales receipt as proof of purchase date to any RadioShack store. RadioShack will,
at its option, unless otherwise provided by law: (a) correct the defect by product repair without charge for parts and labor; (b) replace the product with one of the same or similar design;
or (c) refund the purchase price. All replaced parts and products, and products on which a refund is made, become the property of RadioShack. New or reconditioned parts and products
may be used in the performance of warranty service. Repaired or replaced parts and products are warranted for the remainder of the original warranty period. You will be charged for
repair or replacement of the product made after the expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God,
abuse, accident, misuse, improper or abnormal usage, failure to follow instructions, improper
installation or maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs other than those provided by a RadioShack Authorized Service Facility;
(c) consumables such as fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs of product removal, installation, set-up service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state.
RadioShack Customer Relations, 200 Taylor Street, 6th Floor, Fort Worth, TX 76102
12/99
RadioShack Corporation
Fort Worth, Texas 76102
43-3548
UPZZ01011BZ
02A03
Printed in China
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement