Manual 12668244
www.CasablancaFanCo.com
Table of Contents
Congratulations on purchasing your new Casablanca® ceiling fan!
It will provide comfort and performance in your home or office
for many years. This installation and operation manual contains
complete instructions for installing and operating your fan.
What to Expect with
Your Installation
Tools Needed
Mounting Options
1.888.227.2178
Ceiling Bracket
We are proud of our work and appreciate the opportunity to supply
you with the best ceiling fan available anywhere in the world.
30 inches
Light Kit
Wiring
9
12
Maintenance
& Cleaning
Operation
?
?
22
PA G E
21
PA G E
1
M8522-01 • 03/10/14 • © Casablanca Fan Company
19
PA G E
17
PA G E
PA G E
PA G E
16
14
Troubleshooting
?
15
5
Canopy
PA G E
8
4
PA G E
Switch Housing
Downrod
PA G E
Blades
7
PA G E
PA G E
6
Motor Housing
3
PA G E
Motor Housing Plate
Ladder
PA G E
Preparation
PA G E
2
PA G E
7 feet
Save your receipt for proof of purchase.
PA G E
To register your fan, please visit:
www.CasablancaFanCo.com/register
www.CasablancaFanCo.com
What to Expect with Your Installation
1.888.227.2178
Read and Save These Instructions
This product conforms to UL Standard 507.
If you are unfamiliar
with wiring, use a
qualified electrician.
WARNINGS
30 inches
from blade tip to
nearest wall or
obstruction
Must be able to
secure the fan to
building structure or
fan-rated outlet box
Know your wiring
You may need a
friend to help you.
Assess location
1
Ceiling angles greater
than 34° will require an
Angled Mounting Kit.
See page 4 for details.
Check box to see
fan weight
7 feet
from bottom
edge of blade
to the floor
Assess ceiling angle
2
Standard Downrod
for ceilings 8-10 feet high
Shorter Downrod
for fans installed close to ceiling
w.1 - To reduce the risk of fire, electrical shock, or personal
injury, mount fan directly from building structure and/or an
outlet box marked acceptable for fan support of 70 lbs (31.8 kg)
and use the mounting screws provided with the outlet box.
w.2 - To avoid possible electrical shock, before installing or
servicing your fan, disconnect the power by turning off the
circuit breakers to the outlet box and associated wall switch
location. If you cannot lock the circuit breakers in the off
position, securely fasten a prominent warning device, such as a
tag, to the service panel.
w.3 - To reduce the risk of fire, electrical shock, or motor damage,
use only Casablanca Solid State Speed Controls.
w.4 - To reduce the risk of personal injury, do not bend the blade
brackets when installing the blade brackets, balancing the blades,
or cleaning the fan. Do not insert foreign objects in between
rotating fan blades.
CAUTIONS
c.1 - All wiring must be in accordance with national and local
electrical codes ANSI/NFPA 70. If you are unfamiliar with wiring,
use a qualified electrician.
c.2 - Use only Casablanca replacement parts.
3
Longer Downrod
for ceilings 10 feet or higher
Select a downrod length
2
M8522-01 • 03/10/14 • © Casablanca Fan Company
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and if not
installed and used in accordance with the instructions may cause
harmful interference to radio communications.
www.CasablancaFanCo.com
Tools Needed
Ladder
Pliers
Wire Strippers
9/64” Drill Bit
(optional)
Power Drill
(optional)
If mounting to a support structure, you will also need these tools.
3
M8522-01 • 03/10/14 • © Casablanca Fan Company
Screwdrivers
1.888.227.2178
34O
CEILING
Mounting Options
OPTION 1
If you have a flat ceiling:
1. You will need a longer downrod (sold separately).
2. If your ceiling angle is greater than 34°, you will
also need an Angled Mounting Kit (sold separately).
Angled
Mounting
Standard
Mounting
Style
Ceiling
Outlet Box
(required)
Use the three steps below to determine if your ceiling angle is greater than 34°
2
1
1.888.227.2178
Support
Structure
Support
Structure
OPTION 2
If you have an angled ceiling:
Ceiling
Outlet Box
(required)
Angled
Mounting
Style
3
34°
PLACE
FOLD
against wall
on dotted line
Guide Touches
BOTH Ceiling & Wall
You need ONLY
a Longer
Downrod
*most common
SLIDE
toward ceiling
Guide Touches Wall
but NOT Ceiling
2
ON
SITUAT
I
1
ON
SITUAT
I
WALL
Standard
Mounting
Hang your fan by a standard downrod (included).
www.CasablancaFanCo.com
Use Standard Mounting
or Low-Profile Mounting
to hang the fan from a flat ceiling.
You need BOTH
a Longer
Downrod &
an Angled
Mounting Kit
4
M8522-01 • 03/10/14 • © Casablanca Fan Company
Use Angled Mounting
to hang the fan from a
vaulted or angled ceiling.
Ceiling Bracket
www.CasablancaFanCo.com
1.888.227.2178
r
we
o
nP
r
Tu
OFF
For angled ceilings, point
opening toward peak.
Use wood screws
Use machine screws
(included) when securing
(provided with outlet
to support structure with
box) when securing to
approved electrical outlet existing ceiling fan-rated
box. Drill 9/64” pilot holes
outlet box. Make sure
in support structure to aid
it is securely installed
in securing ceiling bracket and is acceptable for fan
with hardware found in support of 31.8 kg (70 lbs)
the
hardware bag.
or less.
Make sure all four bumpers are
still attached.
If you are unable to do this,
call Technical Support at
1-888-277-2178.
Refer to warning w.1 on pg. 2
5
M8522-01 • 03/10/14 • © Casablanca Fan Company
To avoid possible electrical shock, before
installing your fan, disconnect the power by
turning off the circuit breakers to the outlet
box associated with the wall switch location.
Preparation
www.CasablancaFanCo.com
If you are installing multiple remote-controlled
fans on the same circuit breaker,
you may need to perform a few extra steps to
prevent interference or faulty operation of your
remote controls.
Go to www.CasablancaFanCo.com/FAQs and click
“How do I properly install multiple remotecontrolled fans?” for more information.
Time Saver Tip: Get a helper
to insert grommets, found in
the
hardware bag, into the
blades while you’re doing the
next couple of steps.
6
M8522-01 • 03/10/14 • © Casablanca Fan Company
1.888.227.2178
Motor Housing Plate
www.CasablancaFanCo.com
Motor Housing
Plate
Screw
Holes
Run the wires coming from the motor
through the hole in the center of the motor
housing plate. Align the screw holes in the
motor housing plate with the screw holes in
the motor assembly.
Install the motor housing plate using
three motor housing plate screws, found
in the
hardware bag. Tighten all
screws securely.
7
M8522-01 • 03/10/14 • © Casablanca Fan Company
1.888.227.2178
Motor Housing
www.CasablancaFanCo.com
Screw
Holes
Motor Housing
Carefully place the motor assembly into the
motor housing and align the screw holes.
Ensure the housing plate rests flush against
motor housing.
Install the motor housing using the
four motor housing screws, found in
the
hardware bag. Tighten all
screws securely.
8
M8522-01 • 03/10/14 • © Casablanca Fan Company
1.888.227.2178
www.CasablancaFanCo.com
Option 1
Downrod
1.888.227.2178
skip to next page
Standard
Downrod
for ceilings 8-10’ high
Steps 1-5 to remove standard downrod pipe
1
2
4
Sold Separately
Slide
3
10
9
8
Steps 6-10 to reassemble with new pipe
9
M8522-01 • 03/10/14 • © Casablanca Fan Company
5
Slide
Option 3
Longer
Downrod
for angled
ceilings or
ceilings 10’ or
higher
Shorter
Downrod
for fans installed
close to ceiling
Included
Option 2
Included
(pre-assembled)
If you need a different downrod length follow these steps:
7
6
www.CasablancaFanCo.com
KEEP!
(not to scale)
8”
&
3/8”
1.888.227.2178
STRIP
CUT
Downrod (continued)
!
KEEP
Remove the pre-installed
setscrew so that the downrod
can be inserted.
The wires can be cut, but
leave at least 8” extending
from the top of the downrod.
Hand tighten the downrod (at
least 4-5 full turns) until it stops.
8”
Tighten the setscrew
with pliers. DO NOT
HAND TIGHTEN.
3/8”
If the setscrew is not tightened
securely, the fan may fall.
10
M8522-01 • 03/10/14 • © Casablanca Fan Company
www.CasablancaFanCo.com
Downrod (continued)
Put the wires and downrod through the canopy.
Let the canopy sit loosely on top of the fan.
DO NOT PICK THE FAN UP BY THE
CANOPY OR WIRES. Place the downrod
ball into the slot in the ceiling bracket.
11
M8522-01 • 03/10/14 • © Casablanca Fan Company
1.888.227.2178
Wiring
www.CasablancaFanCo.com
OM
FR
CEILIN
Note: To connect the wires,
hold the bare metal leads
together and place a wire
connector over them, then twist
clockwise until tight.
G
T
KE
black (live in)
FR
black (ungrounded)
M FA N
white (neutral in)
FRO
Using an orange wire
connector from
the
hardware bag,
connect the black wire
(ungrounded) from the
ceiling to the black wire
from the receiver (marked
“live in”). Connect the
white wire (grounded)
from the ceiling to
the white wire from
the receiver (marked
“neutral in” or
“common in”).
white (grounded)
AC
blue
ING BR
CEILIN
G
OM
FR
blue (light out)
CEIL
black
M
white
green/yellow stripe
O
FR
Using an orange wire
connector from
the
hardware bag,
connect the three
grounding wires
(green, green/yellow
stripe, or bare copper)
coming from the ceiling,
downrod, and hanging
bracket.
RECEIVE
R
black (fan out)
green/yellow stripe
Using the blue wire
connectors from the remote
control hardware bag,
connect the white wire
from the receiver (marked
“common out”) to the white
wire from fan. Connect the
black wire from the receiver
(marked “fan out”) to the
black wire from the fan.
Connect the blue wire from
the receiver (marked ”light
out”) to the blue wire from
the fan. The red wire from
the receiver will not be used,
it has a pre-installed wire
terminator.
white (common out)
green/yellow stripe
(grounding)
OM FAN
FR
OM
FR
1.888.227.2178
OM
RECEIV
ER
Turn the splices upward and push them carefully back through the hanger bracket
into the outlet box. Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the outlet box.
Refer to CAUTION c.1 on pg. 2
12
M8522-01 • 03/10/14 • © Casablanca Fan Company
Wiring (continued)
www.CasablancaFanCo.com
Before
Before
After
After removing the switch plate
cover, remove all wiring from
the switch.
Before
Before
After
After
Insert the wall control into
the outlet box and secure the
two screws using a Phillips
head screwdriver.
Using orange wire connectors,
connect the two black wires
(ungrounded) from the outlet
box. Also connect the two green
or bare wires (grounding) from
the outlet box with the grounding
wire from the wall control.
1.888.227.2178
After
Install the cover plate using a
Phillips Head screwdriver to
secure the two cover plate screws.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Push all connections to the back of the switch box. Spread the
wires apart, with the grounded wires on one side of the switch box
and the ungrounded wires on the other side of the switch box.
13
M8522-01 • 03/10/14 • © Casablanca Fan Company
www.CasablancaFanCo.com
Canopy
Screw
Holes
Position the canopy so that, when
lifted into place, the canopy fits into
the hanging bracket as shown.
Lift the canopy into place so that
the screw holes are aligned.
Insert the two canopy screws
found in the
hardware bag.
Note: Fan style may vary.
14
M8522-01 • 03/10/14 • © Casablanca Fan Company
1.888.227.2178
Blades
www.CasablancaFanCo.com
Insert grommets found in the
hardware
bag into the holes in the blades, then
secure each blade to a blade iron with
screws found in the
hardware bag.
1.888.227.2178
Lightly attach the blade irons to the
motor with the blade iron armature
screws, found in the
hardware bag,
then securely tighten after both screws
are attached.
Your blades are shielded with Dust Armor® which
is a nanotechnology coating that repels dust. For
cleaning the fan, use soft brushes or cloths to prevent
scratching. Cleaning agents may damage the finishes.
15
M8522-01 • 03/10/14 • © Casablanca Fan Company
www.CasablancaFanCo.com
Switch Housing
Screw two housing assembly screws
from the
hardware bag halfway into
the motor housing. It does not matter
which two screw holes you choose.
Feed the wire plug through the center
hole of the upper switch housing, then
wrap keyhole slots around the screws and
twist counterclockwise.
the
1.888.227.2178
Insert the third screw, found in
hardware bag, into place and then
tighten all three screws.
Make sure the upper switch housing is securely
attached to the mounting plate. Failure to properly
secure all 3 assembly screws could result in the switch
housing fixture falling.
16
M8522-01 • 03/10/14 • © Casablanca Fan Company
www.CasablancaFanCo.com
Light Kit
1.888.227.2178
Socket
Ring Tool
Socket Ring
Shade
Socket
To install each shade, remove the socket
ring from the socket. Insert the shade
onto the socket and install the socket
ring. Tighten each socket ring by turning
clockwise with the socket ring tool.
Want to install your fan without a light kit?
Go to www.CasablancaFanCo.com/FAQs and click
“How do I install my fan without the light kit?”
Connect the plugs from the upper and
lower switch housings. Make sure to line up
the colored markings on the connectors.
17
M8522-01 • 03/10/14 • © Casablanca Fan Company
Lift the lower switch housing up and align
the screw holes in the upper and lower
switch housings.
Note: In compliance with US federal energy regulations, this ceiling
fan contains a device that restricts its light output. Exceeding the
wattage limit marked on the MAX wattage sticker affixed to the
light socket(s) may result in fire hazard or improper operation.
www.CasablancaFanCo.com
Light Kit (continued)
1.888.227.2178
CONGRA
T
YOU’REULATIONS!
DONE!
Install the three switch housing
screws, found in the
hardware
bag. Tighten all three screws securely.
Install a bulb into each of the sockets.
When necessary, replace with bulbs of
the same type and wattage.
Make sure the lower switch housing is securely attached to
the upper switch housing. Failure to properly secure all 3
assembly screws could result in the light fixture falling.
18
M8522-01 • 03/10/14 • © Casablanca Fan Company
See next page for fan
operation instructions.
Operation
www.CasablancaFanCo.com
1.888.227.2178
If you are installing multiple remote-controlled fans on
the same circuit breaker, you may need to perform a few
extra steps to prevent interference or faulty operation of
your remote controls.
Battery
Go to www.CasablancaFanCo.com/FAQs and click
“How do I properly install multiple remote-controlled fans?”
for more information.
Battery
Holder
4
Fan
Power
Battery
Door
Before operating the wall control, press on the
battery door to eject it. Unscrew the battery
holder. Insert the battery, found in the control
hardware bag, with the positive (+) side facing
downward. Reinstall the battery holder and
reinsert the battery door into the wall control.
er
w
o
nP
r
Tu
ON
19
M8522-01 • 03/10/14 • © Casablanca Fan Company
Note: The remote must be paired before
the fan will operate.
Within 3 minutes of restoring power to the
fan, press both the Fan Off button and the
4 button for at least four seconds. Your fan
will turn on at the lowest speed to indicate
successful syncing. If it does not, turn off
power to your fan, wait one minute then try
again. If using the transmitter with multiple
fans, repeat this process for each fan.
Operation (continued)
www.CasablancaFanCo.com
Reverse
Button
Fan
Speed
(Low)
Fan
Speed
(a)
Lights
Down
Lights
Up
Reverse
Fan
Power
• The lights will flash for visual
confirmation.
• The lights will stay on 50%
brightness for 20 seconds and
then begin to dim. After a total
of 30 seconds, the lights will be
completely off.
(b)
Battery
Holder
Quickly press the up or down arrow
to turn the lights off and on. Hold
the up or down arrow to raise or
dim the light level. The reverse
button changes the direction that
the blades turn. The power button
turns the fan off and on.
The Safe-Exit Program gives
you about thirty seconds of
light when you turn the lights
off to exit the room before the
lights go out. To use Safe-Exit:
• Press the fan power button
off for at least three seconds to
initiate the Safe-Exit Mode.
(High)
The reverse button on the wall
control changes the air flow
pattern. In warm weather, use
(a) downward air flow pattern.
In cold weather, use (b) upward
air flow pattern.
20
M8522-01 • 03/10/14 • © Casablanca Fan Company
1.888.227.2178
Maintenance & Cleaning
www.CasablancaFanCo.com
er
w
o
nP
r
Tu
OFF
Be sure to turn off
power to the fan
before performing
any maintenance or
relamping.
For cleaning the fan, use soft brushes or
cloths to prevent scratching. Cleaning
products may damage the finishes.
For questions regarding removing a light kit, call
customer service 1-888-227-2178.
21
M8522-01 • 03/10/14 • © Casablanca Fan Company
1.888.227.2178
www.CasablancaFanCo.com
Troubleshooting
Fan doesn’t work
Excessive wobbling
Noisy Operation
• Make sure power switch is on.
• Tighten all of the blade and
blade iron screws until they
are snug.
• Tighten the blade and blade
iron screws until they are snug.
• Press a fan speed button (1-4).
• Check the wall control battery.
• Make sure that you have paired
the wall control.
• Check the circuit breaker to
ensure the power is turned on.
• Make sure the blades spin freely.
• Turn off power from the circuit
breaker, then loosen the canopy
and check all the connections
according to the wiring diagram
on page 12-13.
• Check the plug connection in
the switch housing.
• Check to see if any of the
blades are cracked. If so, replace
all of the blades.
• Turn the power off, support
the fan carefully, and check
that the hanger ball is
properly seated.
1.888.227.2178
Lights dim when turned on or do not turn on at all.
• Make sure the wattage of the
light bulbs installed matches
the specifications on the light
sockets.
• Use the provided balancing
kit and instructions to balance
the fan.
If you have multiple remotes or
multiple remote-controlled fans
installed on the same circuit
breaker and you are experiencing
interference or faulty operation of
your remote controls, please go to
www.CasablancaFanCo.com/FAQs
and click “How do I properly install
multiple remote-controlled fans?”
for information on how to correct
this issue.
Remote doesn’t work
• Install a fresh battery in the wall
control.
• Make sure you have paired the
remote.
22
M8522-01 • 03/10/14 • © Casablanca Fan Company
AUTHORIZED SERVICE
CENTERS
For the most updated list of
Casablanca Authorized Service
Centers, visit
www.CasablancaFanCo.com or
call toll free 1-888-227-2178.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising