ABP-1C

ABP-1C
Installation
SV Valve
ABP-1C Single Valve
Ablution System
S67-610 1C ABP Single Compression
Valve (SV)
S67-609 1C ABP Single Compression
Valve with Lever (SVL)
Table of Contents
Rough-Ins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Cleaning and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . 5
SVL Valve
IMPORTANT!
Read this entire installation manual to ensure proper installation. When finished with the
installation, file this manual with the owner or maintenance department. Compliance and
conformity to local codes and ordinances is the responsibility of the installer.
Installation
Packing List
IS
TH
SIDE
UP
•
•
•
•
Separate parts from packaging and make sure all parts are accounted for before
discarding packaging material. If any parts are missing, do not begin installation until
you obtain the missing parts.
Make sure that all water supply lines have been flushed and then completely turned off
before beginning installation. Debris in supply lines can cause valves to malfunction.
Product warranties may be found under “Products” on our web site at
www.bradleycorp.com.
215-1812 Rev. A; ECN 14-03-005B
© 2014 Bradley
Page 1 of 5 7/1/2014
P.O. Box 309, Menomonee Falls, WI USA 53052-0309
PHONE 800.BRADLEY (800.272.3539) FAX 262.251 5817
bradleycorp.com
Single Compression Valve for ABP-1C Single Valve Ablution SystemInstallation
1a
Rough-in (Single Valve - SV)
Standard Installation
Handle
Sleeve
Escutcheon
1/2" NPT
Inlets and
Outlets
Optional
Stop
5"
(127mm)
Note orientation
of Sleeve
1/2" NPT
1-7/16"
(37mm)
Alternate Installation for
shallow wall depth
3-1/4" standard
installation rough-in
2-1/2" alternate
installation rough-in
Note Sleeve rotated
180 from standard
installation
No Stop
Ø 1-1/2" hole
required
With Stop
1-5/8"
(42mm)
1-1/2"
(39mm)
3/4"
(20mm)
4-1/2"
(115mm)
Escutcheon
Outline
Wall opening
outline
3"
(77mm)
Escutcheon
Outline
3-1/4"
(83mm)
2
7/1/2014
Bradley • 215-1812 Rev. A; ECN 14-03-005B
Single Compression Valve for ABP-1C Single Valve Ablution System
Installation
1b
Rough-in (Single Valve with Lever Handle - SVL)
Standard Installation
Handle
Sleeve
Escutcheon
1/2" NPT
Inlets and
Outlets
Optional
Stop
5"
(127mm)
1/2" NPT
Note orientation
of Sleeve
Alternate Installation for
shallow wall depth
1-7/16"
(37mm)
3-3/8" to 4" standard
installation rough-in
2-3/8" to 3-3/4" alternate
installation rough-in
Note Sleeve rotated
180 from standard
installation
No Stop
Ø 1-1/2" hole
required
With Stop
1-5/8"
(42mm)
1-1/2"
(39mm)
3/4"
(20mm)
4-1/2"
(115mm)
Escutcheon
Outline
3"
(77mm)
Wall opening
outline
Escutcheon
Outline
3-1/4"
(83mm)
Bradley • 215-1812 Rev. A; ECN 14-03-005B
7/1/2014
3
Single Compression Valve for ABP-1C Single Valve Ablution SystemInstallation
2
A
Installation
Flush the supply line before
making connection.
Connect valve to supply line and
spout or diverter. Valve must be
held in place using rigid piping
and clamp (supplied by installer).
B
Attach escutcheon, sleeve and
handle to valve after wall is
finished.
For further information see operation and service guides
215-1369-2C (for SVL) and 215-1369-2D (for SV)
FRONT MOUNT
Elbows, Adapters and
Piping supplied by others
Model SVL Shown,
Model SV is assembled in
teh same manner
1/2" Brass Pipe
Plug (Supplied
by Bradley)
1/2" NPT
Outlets
Optional
1/2" Stop
(S27-102)
Optional 1C
Spout (SSPS
Shown, SX
assembled in the
same manner)
3/8" NPT Outlet
Optional
ABL Spout
Quick
Connect Kit
(S45-2848)
1/2" Brass Pipe
Plug (Supplied
by Bradley)
REAR MOUNT
1/2" NPT
Outlets
Elbows, Adapters and
Piping supplied by others
Model SVL Shown,
Model SV is assembled in
teh same manner
Optional
1/2" Stop
(S27-102)
Optional 1C
Spout (SSPS
Shown, SX
assembled in the
same manner)
Optional
ABL Spout
Quick
Connect Kit
(S45-2848)
3/8" NPT Outlet
Frame
4
7/1/2014
Bradley • 215-1812 Rev. A; ECN 14-03-005B
Installation
Single Compression Valve for ABP-1C Single Valve Ablution System
Cleaning and maintenance instructions for stainless steel
Material Description: Stainless steel is extremely durable, and maintenance is simple and inexpensive. Proper care,
particularly under corrosive conditions, is essential. Always start with the simplest solution and work your way toward
the more complicated.
Routine cleaning: Daily or as often as needed use a solution of warm water and soap, detergent, or ammonia. Apply the
cleaning solution per the manufacturer’s instructions and always use a soft cloth or sponge to avoid damaging the finish.
Stubborn Stains: To remove stains from stainless steel use a stainless steel cleaner and polish such as Ball®
stainless steel cleaner or a soft abrasive. Always follow the manufacturer’s instructions and apply in the same
direction as the polish lines.
Spout/Head: If the spout/head delivers an uneven spray, remove the spout/head from the unit, disassemble, and
remove foreign matter. Then reassemble spout/head and reinstall into unit.
CAUTION! Never use ordinary steel wool or steel brushes on stainless steel. Always use stainless steel
wool or stainless steel brushes.
Special Situations for Material
Fingerprints and Smears: To remove fingerprints or smears use a high quality stainless steel cleaner and polish in
accordance with the manufacturer’s instructions. Many of these products leave a protective coating that helps prevent
future smears and fingerprints.
Grease and Oil : To remove grease and oil use a quality commercial detergent or caustic cleaner. Apply in
accordance to the manufacturer’s instructions and in the direction of the polish lines.
Precautions: Avoid prolonged contact with chlorides (bleaches, salts), bromides (sanitizing agents), thiocyanates (pesticides,
photography chemicals, and some foods), and iodides on stainless steel equipment, especially if acid conditions exist.
CAUTION! Do not permit salty solutions to evaporate and dry on stainless steel.
The appearance of rust streaks on stainless steel leads to the belief that the stainless steel is rusting. Look for the actual
source of the rust in some iron or steel particles which may be touching, but not actually a part of the stainless steel structure.
NOTE: Strongly acidic or caustic cleaners may attack the steel, causing a reddish film to appear. The use of these
cleaners should be avoided.
Brand Names: Use of brand names is intended only to indicate a type of cleaner. This does not constitute an
endorsement, nor does the omission of any brand name cleaner imply its inadequacy. Many products named are
regional in distribution, and can be found in local supermarkets, department and hardware stores, or through your
cleaning service. It is emphasized that all products should be used in strict accordance with package instructions.
Bradley • 215-1812 Rev. A; ECN 14-03-005B
7/1/2014
5
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising