USB-SDP-CABLEZ User Guide UG-404

USB-SDP-CABLEZ User Guide UG-404
USB-SDP-CABLEZ User Guide
UG-404
One Technology Way • P.O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com
USB-SDP-CABLEZ Serial Interface Board
FEATURES
The USB-SDP-CABLEZ provides USB connectivity through a
USB 2.0 high speed connection to the computer, allowing users
to evaluate components from a PC application. The USB-SDPCABLEZ is based on a USB-to-serial engine, which has I2C, SPI,
and GPIO lines available, with a small 10-pin connector.
USB-to-serial interface
Peripherals exposed
I2C
SPI
GPIO
USB 2.0 PC connectivity
This user guide provides instructions for installing the USBSDP-CABLEZ hardware and software onto a computer. The
necessary installation files are available to download from
the USB-SDP-CABLEZ evaluation board page or from the
evaluation tools page for the product being evaluated on
http://www.analog.com.
GENERAL DESCRIPTION
This user guide describes the USB-SDP-CABLEZ serial
interface board from Analog Devices, Inc. The USB-SDPCABLEZ is primarily used to communicate with certain Analog
Devices evaluation boards to support customer evaluation. It
can also be used by customers to communicate with supported
Analog Devices components on their own board, using the
appropriate Analog Devices evaluation software to facilitate
in-system debugging and programming as required during
product development.
The Getting Started section provides software and hardware
installation procedures, PC system requirements, and basic board
information. The Evaluation Board Hardware section provides
information on the USB-SDP-CABLEZ components. The USBSDP-CABLEZ schematics are provided in the Evaluation Board
Schematics section.
For more information about the USB-SDP-CABLEZ board, go
to www.analog.com/usb-sdp-cablez.
The primary audience for this user guide is the system engineer.
This user guide describes how to set up the USB-SDP-CABLEZ
board and begin USB communications to the PC.
10664-001
USB-SDP-CABLEZ
Figure 1.
PLEASE SEE THE LAST PAGE FOR AN IMPORTANT
WARNING AND LEGAL TERMS AND CONDITIONS.
Rev. A | Page 1 of 12
UG-404
USB-SDP-CABLEZ User Guide
TABLE OF CONTENTS
Features .............................................................................................. 1
USB Driver Installation ................................................................4
General Description ......................................................................... 1
Adapter Boards ..............................................................................4
USB-SDP-CABLEZ .......................................................................... 1
Powering Up/Powering Down the USB-SDP-CABLEZ...........5
Revision History ............................................................................... 2
Evaluation Board Hardware .............................................................6
Product Overview............................................................................. 3
LEDs ................................................................................................6
Package Contents .......................................................................... 3
Connector Details .........................................................................6
Technical or Customer Support.................................................. 3
Power...............................................................................................6
Analog Devices Website .............................................................. 3
Evaluation Board Schematics...........................................................8
Getting Started .................................................................................. 4
Bill of Materials ........................................................................... 11
PC Configuration ......................................................................... 4
REVISION HISTORY
7/12—Rev. 0 to Rev. A
Changes to Table 1 ............................................................................ 7
Changes to Power LED (LED3) Section and Figure 5 ................. 6
6/12—Revision 0: Initial Version
Rev. A | Page 2 of 12
USB-SDP-CABLEZ User Guide
UG-404
PRODUCT OVERVIEW
The USB-SDP-CABLEZ board includes the following:
ANALOG DEVICES WEBSITE
•
•
The Analog Devices website, www.analog.com, provides
information about a broad range of products: analog integrated
circuits, amplifiers, converters, and digital signal processors.
•
USB-to-serial engine
1 × 10-pin connector
• AMP 10-way Micro-MaTch male connector
Peripherals exposed
• I2C
• SPI
• GPIO
PACKAGE CONTENTS
The USB-SDP-CABLEZ board package contains the following:
•
•
•
USB-SDP-CABLEZ serial interface
1 m USB Standard-A-to-Mini-B cable
USB-I2C-ADPTZ adapter board (used to convert the
10-pin connector to a 3-pin I2C header)
Also, note that MyAnalog.com is a free feature of the Analog
Devices website that allows customization of a Web page to
display only the latest information about products of interest
to you. You can choose to receive weekly email notifications
containing updates to the Web pages that meet your interests,
including documentation errata for all documents. MyAnalog.com
provides access to books, application notes, data sheets, code
examples, and more.
Visit MyAnalog.com to sign up. If you are a registered user,
simply log on. Your user name is your email address.
Contact the vendor where the USB-SDP-CABLEZ board was
purchased, or contact Analog Devices if anything is missing.
TECHNICAL OR CUSTOMER SUPPORT
Analog Devices customer support can be reached in the
following ways:
•
•
•
•
Visit the EngineerZone® for community technical support
at ez.analog.com.
Phone questions to 1-800-ANALOGD
Contact your Analog Devices local sales office or
authorized distributor.
Send questions by mail to
Analog Devices, Inc.
Three Technology Way
P.O. Box 9106
Norwood, MA 02062-9106
USA
Rev. A | Page 3 of 12
UG-404
USB-SDP-CABLEZ User Guide
GETTING STARTED
This section provides specific information to assist with using the
USB-SDP-CABLEZ board as part of the user’s evaluation system.
The following topics are covered:
•
•
•
PC configuration
USB installation
Powering up/powering down the USB-SDP-CABLEZ
PC CONFIGURATION
For correct operation of the SDP board, the user’s computer
must have the following minimum configuration:
•
•
Windows XP Service Pack 2 or Windows Vista®
USB 2.0 port
When removing the USB-SDP-CABLEZ board from the
package, handle the board carefully to avoid the discharge
of static electricity, which can damage some components.
USB DRIVER INSTALLATION
Perform the following tasks to correctly install the USB-SDPCABLEZ driver software onto the computer. The software can
be obtained from www.analog.com/usb-sdp-cablez and is called
Common Run-Time Installer. Version 2.0.0 or greater is required
to operate with the USB-SDP-CABLEZ.
1.
2.
3.
Run the setup.exe application found in the installer zip file. If
running Windows XP, it may be necessary for the machine
to restart shortly after the installation process begins.
The first part of the installer places the required Run-Time
engine and software drivers for the USB-SMBUS-CABLE
I2C dongle onto the PC.
After this, the installer for the USB-SDP-CABLEZ runs.
As part of this, the .NET Framework 3.5 is installed, if not
already on the PC. If the .NET Framework 3.5 is installed
on the computer, this stage is skipped and only the driver
package installation is installed.
Connecting the USB-SDP-CABLEZ Board to the PC
Attach the USB-SDP-CABLEZ board to a USB 2.0 port on the
computer via the Standard-A-to-Mini-B cable provided.
Verifying Driver Installation
10664-002
Installing the Software
Figure 2. Device Manager
ADAPTER BOARDS
The USB-SDP-CABLEZ uses a 10-pin Micro-MaTch male
connector as its interface connector. However, some older
evaluation kits use a different connector for I2C connections
and require the use of an adapter board to convert the 10-pin
connector to an appropriate connection.
The USB-SDP-CABLEZ is supplied with the USB-I2C-ADPTZ
adapter board to convert the 10-pin Micro-MaTch connector to
a 3-pin 0.1" header connector.
Before using the USB-SDP-CABLEZ board, verify that the
driver software has installed properly.
10664-003
Open the Windows Device Manager and verify that the USBSDP-CABLEZ board appears under ADI Development Tools,
as shown in Figure 2.
Figure 3. USB-I2C-ADPTZ Adapter Board
Rev. A | Page 4 of 12
USB-SDP-CABLEZ User Guide
UG-404
The 10-way Micro-MaTch connector is fitted to the USB-I2CADPTZ board as shown in Figure 3, paying attention to the
polarization of the Micro-MaTch connector (indicated by the
red markings on the ribbon cable) and the key on the MicroMaTch connector.
A USB-I2C5W-ADPTZ adapter board is also available, but is
not supplied with the USB-SDP-CABLEZ. This board is only
included in the specific evaluation kits that require it. It is
connected to the Micro-MaTch connector in exactly the same
way as the USB-I2C-ADPTZ.
POWERING UP/POWERING DOWN THE USB-SDPCABLEZ
This section describes how to safely power up and power down
the USB-SDP-CABLEZ.
Powering Up the USB-SDP-CABLEZ Board
1.
2.
3.
Connect the USB-SDP-CABLEZ board to the evaluation
board through the 10-pin mating connector, using an
optional adapter if required.
Power up the evaluation board.
Connect the USB port on the computer to the USB-SDPCABLEZ board.
Powering Down the USB-SDP-CABLEZ Board
1.
10664-004
2.
3.
Figure 4. USB-I2C5W-ADPTZ Adapter Board
Rev. A | Page 5 of 12
Disconnect the USB port on the computer from the
USB-SDP-CABLEZ board.
Power down the daughter evaluation board.
Disconnect the USB-SDP-CABLEZ board from the
evaluation board.
UG-404
USB-SDP-CABLEZ User Guide
EVALUATION BOARD HARDWARE
LED2
This section describes the hardware design of the USB-SDPCABLEZ board.
The following topics are covered:
•
•
•
The LEDs section describes the USB-SDP-CABLEZ
on-board LEDs.
The Connector Details section details the pin assignments
on the 10-pin connector.
The Power section lists the power requirements of the
USB-SDP-CABLEZ and identifies the connector power
inputs and output pins.
The red LED is used as a diagnostic tool for evaluation
application developers, usually to identify a particular board
when more than one USB-SDP-CABLEZ is connected to a
given PC.
CONNECTOR DETAILS
The USB-SDP-CABLEZ board provides one Micro-MaTch
10-way male connector. Through this connector, the peripheral
communication interfaces of the USB-to-serial engine are
exposed. The exposed peripherals are
There are three LEDs located on the USB-SDP-CABLEZ board
(see Figure 5).
•
•
•
Power LED (LED3)
Connector Pin Assignments
The green power LED indicates that the USB-SDP-CABLEZ
board is powered up. This is not an indication of USB
connectivity between the USB-SDP-CABLEZ and the PC.
Table 1 lists the connector pins and identifies the functionality
assigned to each connector pin on the USB-SDP-CABLEZ board.
LEDs
SPI
I2C
GPIO
POWER
10664-005
The USB-SDP-CABLEZ board is powered by the USB connector.
Pin 4 (VBUS) of the 10-way connector is connected to the 5 V
line of the USB connector, providing 5 V ± 10% as an output
from the USB-SDP-CABLEZ board.
Figure 5. USB-SDP-CABLEZ Board LEDs
A small current can be drawn from this pin, but it should not be
more than 20 mA to avoid potential problems with USB port
current limiting.
LED1
This yellow LED is currently not used in normal operation,
but it may turn on when the board is initially connected to
USB power.
Rev. A | Page 6 of 12
USB-SDP-CABLEZ User Guide
UG-404
Table 1. 10-Pin Connector Assignments
Pin No.
1
2
3
4
5
6
7
8
9
10
Pin Name
I2C.SCL
GND
I2C.SDA
VBUS
SPI.MISO
GPIO
SPI.SCLK
SPI.MOSI
SPI.CS.A
GND
Description
I2C Serial Clock.
Ground Connection.
I2C Serial Data.
Voltage Bus. Connected directly to the USB 5 V supply.
SPI Master In, Slave Out Data.
General-Purpose Input/Output.
SPI Clock.
SPI Master Out, Slave In Data.
SPI Chip Select A.
Ground Connection.
Table 2. 3-Pin/5-Pin Header Assignments
Pin No.
1
2
3
4
5
Pin Name
SCL
SDA
GND
CONV
ALERT
Description
I2C Serial Clock.
I2C Serial Data.
Ground Connection.
Digital Output. Available on USB-I2C5W-ADPTZ only.
Digital Input. Available on USB-I2C5W-ADPTZ only.
Rev. A | Page 7 of 12
UG-404
USB-SDP-CABLEZ User Guide
EVALUATION BOARD SCHEMATICS
This section provides the schematic drawings for the following boards:
•
•
USB-SDP-CABLEZ—USB-to-serial interface (see Figure 6).
USB-I2C-ADPTZ and USB-I2C5W-ADPTZ—adapter boards (see Figure 7).
Rev. A | Page 8 of 12
C8
10µF
Figure 6. USB-SDP-CABLEZ—USB-to-Serial Interface
Rev. A | Page 9 of 12
C16
100nF
VBUS
R16
0Ω
2
D2
OUT 5
NC 4
3 EN
C17
100nF
+3.3V
C4
10µF
L3
R3
10kΩ
+3.3V
C13
100nF
C5
10µF
C18
100nF
C6
10µF
C9
100nF
VPLL
C19
100nF
2.2kΩ
R4
R1
10kΩ
POWER
C1
27pF
C2
27pF
Y1
12MHz
R9
C12
100nF
12kΩ
LED3
GREEN
R10
680Ω
+3.3V
+3.3V
C11
100nF
C22
100nF
C10
100nF
C23
100nF
VCORE
C7
10uF
+3.3V
C15
100nF
VUSB
93AA56BT-I/OT
600Ω AT 100MHz
L2
2
6
VCC VSS
+3.3V
C14
100nF
3 DI U2 DO 1
5 CS
4 CLK
600Ω AT 100MHz
+3.3V
R2
10kΩ
+3.3V
GND
1 ADM6384YKS29D1Z
RESET
1 IN
2 GND
D1
U3
4
VCC
+3.3V
C20
100nF
MR
ADP121
U4
3
100nF
C21
USB-MINI-B-UX60SC-MB-5S8
4
SHLD2 IO
GND 5
7
J2
VBUS 1
SHLD1
D– 2
D+ 3
6
PGB1010603
C3 10nF
PGB1010603
L1
600Ω AT 100MHz
VPLL VCORE
I2C.SCL
I2C.SDA
3 OSCO
13 TEST
2 OSCI
63 EECS
62 EECLK
61 EEDATA
6 REF
14 RESET
7 DM
8 DP
50 VREGIN
49 VREGOUT
VUSB
10 GNDA
+3.3V
FT2232HQ
U1
VBUS
U11
VCC 8
1 SX
RX 2
TX 3
P82B96
RY 6
7 SY
TY 5
GND 4
C32
100nF
16
17
18
19
21
22
23
24
26
27
28
29
30
32
33
34
38
39
40
41
43
44
45
46
48
52
53
54
55
57
58
59
PWREN 60
SUSPEND 36
BCBUS0
BCBUS1
BCBUS2
BCBUS3
BCBUS4
BCBUS5
BCBUS6
BCBUS7
BDBUS0
BDBUS1
BDBUS2
BDBUS3
BDBUS4
BDBUS5
BDBUS6
BDBUS7
ACBUS0
ACBUS1
ACBUS2
ACBUS3
ACBUS4
ACBUS5
ACBUS6
ACBUS7
ADBUS0
ADBUS1
ADBUS2
ADBUS3
ADBUS4
ADBUS5
ADBUS6
ADBUS7
+3.3V
4
9
12
37
64
VPHY
PLLV
VCORE
VCORE
VCORE
VCORE
20
31
42
56
VCCIO
VCCIO
VCCIO
VCCIO
GND
GND
GND
GND
GND
GND
GND
GND
1
5
11
15
25
35
47
51
VBUS
R6
2.2kΩ
U10-A
6
4
DNP
LK6
1
6
I/O1A I/O1B
2 GND VBUS 5
3 I/O2A I/O2B 4
U12
USBLC6-2
USBLC6-2P6
DNP
LK5
C33
100nF
R7
2.2kΩ
+3.3V
+3.3V
C31
100nF
VBUS PLACE THIS CAP
BESIDE VBUS PIN
NC7WZ07P6X
3
U10-B
100Ω
100Ω
R15
SPI.SCLK
I2C.SCL
I2C.SDA
R14
R8
2.2kΩ
SN74LVC1G86DBV
4
SPI.SCLK.PULL.LOW.EN
U9
2
1
R22
100kΩ
+3.3V
NC7WZ07P6X
1
R13
100Ω
SPI.SCLK.INV.EN
0Ω
R17
+3.3V
C30
100nF
SPI.MOSI
SPI.MISO
SPI.CS.A
GPIO0
R5
2.2kΩ
+3.3V +3.3V
LED2
SUPER RED
R11
680Ω
SPI.CS.A
SPI.MOSI
J3-10
J3-9
J3-8
J3-7
J3-6
J3-5
SPI.SCLK
J3-4
SPI.MISO
J3-3
J3-2
J3-1
R12
680Ω
VBUS
MICRO-MATCH SMD SOCKET
LED1
YELLOW
STATUS
GPIO0
USB-SDP-CABLEZ User Guide
UG-404
10664-006
UG-404
USB-SDP-CABLEZ User Guide
10-WAY 2 × 5 WAY
DIL 0.1" HEADER
10-WAY MICRO-MATCH
CONNECTOR
I2C.SCL
J1-1
GND
J1-2
J2-3
I2C.SDA
J1-3
J2-4
VBUS
J1-4
J2-1
J2-2
GND
SPI.MISO
J2-5
GPIO1
J2-6
SPI.SCLK
J2-7
SPI.MOSI
J2-8
SPI.CS.A
J2-9
GND
J2-10
J1-5
J1-6
J1-7
J1-8
J1-9
J1-10
GND
3- OR 5-WAY 0.1" HEADER
J3-2
J3-3
J3-4
J3-5
I2C.SCL
I2C.SDA
GND
GPIO1
GND
SPI.MISO
Figure 7. USB-I2C-ADPTZ and USB-I2C5W-ADPTZ—Adapter Boards
Rev. A | Page 10 of 12
10664-007
J3-1
USB-SDP-CABLEZ User Guide
UG-404
ORDERING INFORMATION
BILL OF MATERIALS
Table 3. USB-SDP-CABLEZ
Qty.
2
6
20
2
1
1
3
1
1
1
2
3
5
1
3
3
1
1
1
1
1
Reference Designator
C1, C2
C3, C4, C5, C6, C7, C8
C9, C10, C11, C12, C13, C14, C15,
C16, C17, C18, C19, C20, C21, C22,
C23, C30, C30, C31, C32, C33
D1, D2
J2
J3
L1, L2, L3
LED1
LED2
LED3
LK5, LK6
R1, R2, R3
R4, R5, R6, R7, R8
R9
R10, R11, R12
R13, R14, R15
R16
R22
U1
U2
U3
1
1
1
1
1
1
U4
U9
U10
U11
U12
Y1
Description
Capacitor, 27 pF, 0402
Capacitor, 10 nF, 0402
Capacitor, 100 nF, 0402
ESD/TVD protection diode, 0603
USB Mini-B connector
10-way Micro-MaTch SMD socket
Ferrite bead, 600 Ω at 100 MHz, 0603
Yellow LED, 0603
Red LED, 0603
Green LED, 0603
Solder links, not fitted
Resistor, 10 kΩ, 0402
Resistor, 2.2 kΩ, 0402
Resistor, 12 kΩ, 0402
Resistor 680 Ω, 0402
Resistor, 100 Ω, 0603
Resistor, 0 Ω, 0402
Resistor, 100 kΩ, 0402
USB serial converter, FTDI FT2232H, QFN-64
SPI EEPROM, Microchip 93AA56BT-I, SOT23-6
Supervisory circuit with watchdog and manual reset,
Analog Devices ADM6384YKS29D1Z-R7, 4-lead SC70
3.3 V linear regulator, Analog Devices ADP121, 5-lead TSOT
2-input exclusive OR gate, TI SN74LVC1G86DBV, SOT23-5
Open-drain buffer, Fairchild NC7WZ07P6X, SC70-6
I2C bus buffer, NXP P82B96, SO8NB
Low capacitance ESD protection, ST USBLC6-2P6, SOT666
Crystal, 12 MHz, NDK NX3225SA-12.000000 MHz
Table 4. USB-I2C-ADPTZ and USB-I2C5W-ADPTZ
Qty.
1
1
1
Reference Designator
J1
J2
J3
Description
10-way Micro-MaTch socket
2 × 5-way 0.1" pitch header, not fitted
3-way/5-way right angle 0.1" pitch female header
Rev. A | Page 11 of 12
UG-404
USB-SDP-CABLEZ User Guide
I2C refers to a communications protocol originally developed by Philips Semiconductors (now NXP Semiconductors).
ESD Caution
ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection
circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.
Legal Terms and Conditions
By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions
set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you
have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc.
(“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal,
temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided
for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional
limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term
“Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including
ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may
not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to
promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any
occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board.
Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice
to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO
WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED
TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL
PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF
THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE
AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable
United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of
Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby
submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed.
©2012 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
UG10664-0-7/12(A)
Rev. A | Page 12 of 12
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising