CSI 7030 Series User`s manual

CSI 7030 Series User`s manual
2 Channel/4 Channel
Video Multiplexer
USER’S MANUAL
7030 and 7040 Series
WORLD HEADQUARTERS
55 Cabot Court
Hauppauge, N.Y. 11788 USA
Tel: (631) 273-0404
Fax: (631) 273-1638
www.commspecial.com
Email: [email protected]
Communications Specialties Pte Ltd
100 Beach Road
#22-09 Shaw Tower
Singapore 189702
Tel: +65 6391 8790 Fax: +65 6396 0138
Email: [email protected]
P/N: 122051 Rev. C
in material and workmanship under normal use and service. A Return
Material Authorization (RMA) number must be obtained from CSI at
the expense and risk of the Buyer. CSI’s Obligation under this warranty
will be limited, at its option, to either the repair or replacement of
defective units, including free materials and labor. In no event shall CSI
be responsible for any incidental or consequential damages or loss of
profits or goodwill. CSI shall not be obligated to replace or repair
equipment that has been damaged by fire, war, acts of God, or similar
causes, or equipment that has been serviced by unauthorized personnel,
altered, improperly installed or abused.
RMA numbers and repairs can be obtained from:
Communications Specialties, Inc.
55 Cabot Court
Hauppauge, NY 11788 USA
Tel: (631) 273-0404 Fax: (631) 273-1638
www.commspecial.com
Email: [email protected]
CONTENTS
General Information .................................................... 2
Introduction ............................................................ 2
Technical Specifications .......................................... 2
Installation Instructions .............................................. 4
Installation Procedure ............................................. 4
Alarm Switch Settings ............................................ 4
Indicator LEDs and Alarm Circuitry ...................... 5
Operating Pointers and Troubleshooting .................... 6
Maintenance ............................................................... 7
Or, in the Asia Pacific Region:
Warranty ..................................................................... 7
Communications Specialties Pte Ltd
100 Beach Road
#22-09 Shaw Tower
Singapore 189702
Tel: +65 6391 8790 Fax: +65 6396 0138
Email: [email protected]
Please have your serial number (located on the top label of the unit)
available when contacting us.
8
1
GENERAL INFORMATION
Introduction
The Pure Digital Fiberlink® 7030 and 7040 Series transmit multiple
channels of uncompressed composite video over a single fiber optic
cable. The 7030 Series (2 channels video) and 7040 Series (4 channels
video) provide 7 MHz bandwidth per video channel and are compatible
with NTSC, PAL and SECAM video standards. Systems are offered
for use with single mode or multimode fiber. With a wide operating
temperature range, the systems are suitable for any indoor or protected
outdoor environment.
Systems consist of two units (transmitter and receiver), each
equipped with indicator LEDs to continuously indicate the presence of
power and video signals. The system is available in box or card
version. Card units fit within the model 6000A card cage.*
Technical Specifications
Model Part Numbering
Configurations:
*Card versions for the
Unit Type
Transmitter Box
Transmitter Card*
Receiver Box
Receiver Card*
Part Number
7030/7040-BXY
7030/7040-CXY
7031/7041-BXY
7031/7041-CXY
X Values:
Y Values:
1 = 850 nm Multimode
S = ST connector
3 = 1310 nm Multimode F = FCPC connector
7 = 1310 nm Single Mode
9 = 1550 nm Single Mode
2
7030 Series fill one
slot in the model
6000A card cage.
Card versions for the
7040 Series fill two
slots.
as to the origin of any operational failure. Be certain that the input and
output signal connections are proper. Due to the number of positions,
Finally, although multimode and single mode devices may look the
same, they will not operate properly together. Using the wrong device
or fiber can easily add more attenuation than specified, resulting in poor
overall performance.
If, after reviewing these possibilities, the system is still not operating, please contact the Customer Service Department for further
assistance. (See page 8 for contact information.)
MAINTENANCE
The Pure Digital Fiberlink 7030 and 7040 Series transmission units
have been manufactured using the latest semiconductor devices and
techniques that electronic technology has to offer. They have been
designed for long, reliable and trouble-free service and are not
normally field repairable. Should difficulty be encountered, Communications Specialties maintains a complete service facility to render
accurate, timely and reliable service of all products.
The only maintenance that can be provided by the user is to
ascertain that optical connectors are free of dust or dirt that could
interfere with light transmission and that electrical connections are
secure and accurate.
All other questions or comments should be directed to our Customer
Service Department. It should be noted that many “problems” can
easily be solved by a simple telephone call.
LIMITED WARRANTY
Communications Specialties, Inc. (CSI) warrants that for a period of
three years after purchase by the Buyer, the Pure Digital Fiberlink
7030 and 7040 Series Transmission Systems will be free from defects
7
RECEIVER:
Video:
OFF: Indicates no video detected over fiber and, as a result,
no video present on output BNC
ON: Indicates video detected over fiber and, as a result,
video present on output BNC
Alarm: ON: Loss of input video or optical signal (rack card only)
OPERATING POINTERS AND TROUBLESHOOTING
Optical Fiber:
The 7030 and 7040 Series are available in versions that operate with
most multimode (MM) and single mode (SM) optical fibers. Be certain
that the correct size fiber is being used for the particular transmitter/
receiver combination.
Also be certain that the attenuation and bandwidth of the fiber optic
cable being used is within the range of the system’s loss budget
specifications.
Troubleshooting:
Multimode fiber optic cable contains an optical fiber with a light
carrying “core” that is only .0025 inches (62.5 microns) in diameter.
Single mode fiber optic cable has an even smaller “core”, only .00032 to
.0004 inches (8-10 microns). This is smaller than a human hair! As a
result, any minute particles of dirt or dust can easily block the fiber
from accepting or radiating light. Therefore, cleanliness is imperative!
Always use the dust caps provided with all optical connectors
whenever they are exposed to air. Also, it is a good idea to gently clean
the tip of an optical connector with a lint-free cloth moistened with
alcohol whenever dust is suspected.
The status of any of the indicator LEDs should provide the first clue
6
Video
Bandwidth ............................ 7 MHz (-3dB)
Input/Output Impedance ...... 75 Ohms
Input/Output Voltage ............ 1 Vp-p nom., 1.1 Vp-p max.
Differential Phase & Gain ..... 0.5o typical; 1.0% typical
Signal-to-Noise Ratio ............ 62 dB CCIR weighted
Signal Connectors ................. BNC
Optical
Operating Wavelength ........... 850 nm, 1310 nm, 1550 nm, MM/SM
Optical Fiber ......................... 62.5/125 microns MM or
.......................................... 8-10/125 microns SM
Optical Connectors ............... ST or FCPC
Wavelength
Loss Budget (in dB)
Distance* (in km)
850 MM
0-20
0-.75
1310 MM
0-25
0-2
1310 SM
0-25
0-60
1550
0-25
0-80
*Note: Distance specifications are only approximate and are not
guaranteed. Operating loss budget must not be exceeded.
Miscellaneous
Operating Temp. Range ........ -35 to +75 degrees C
Operating Power ................... 9 to 24 Volts AC or [email protected] watts (max)
CAUTION! Some versions of the Pure Digital Fiberlink transmitter unit
contain a solid state Laser Diode located within the optical connector.
This device emits invisible infrared electromagnetic radiation which
can be harmful to human eyes. The radiation from this optical connector, if viewed at close range without a fiber optic cable connected to the
optical connector, may be of sufficient intensity to cause instantaneous
damage to the retina of the eye. Direct viewing of this radiation should
be avoided at all times.
3
INSTALLATION INSTRUCTIONS
Alarm Switch Settings (Receiver; Card Version Only)
Installation Procedure
The Pure Digital Fiberlink 7030 and 7040 Series transmission
systems are normally preset for immediate use. There are indicator
LEDs on the units for monitoring purposes. The following instructions
describe the typical installation procedure and the function of the LED
indicators.
1. Connect the fiber optic cable or cables
between the two Pure Digital Fiberlink
units.
2. Apply power to both Pure Digital
Fiberlink units. For box versions using
DC power connections, refer to Figure 1.
3. When power is applied, the green
POWER LED will light, indicating the presence of operating power.
The green VIDEO LED(s) will give an indication as stated on the
following page. Note that the rack card version will have an additional red LED to indicate the presence of an alarm condition (loss of
video).
4. The system should now be operational.
Alarm Switch Settings (Transmitter; Card Version Only)
Switch Position
1
2
3
4
5
Alarm Indication
Loss of Link
Loss of Video 1
Loss of Video 2
Loss of Video 3
(7040 only)
Loss of Video 4
(7040 Only)
4
On
Enabled
Enabled
Enabled
Enabled
Off
Disabled
Disabled
Disabled
Disabled
Enabled
Disabled
Switch Position
1
2
3
4
5
Alarm Indication
Loss of Signal
Loss of Video 1
Loss of Video 2
Loss of Video 3
(7040 only)
Loss of Video 4
(7040 Only)
On
Enabled
Enabled
Enabled
Enabled
Off
Disabled
Disabled
Disabled
Disabled
Enabled
Disabled
Note: “Loss of Link” refers to loss of input signal lock. “Loss of Video”
refers to loss of the respective input video. “Loss of Signal” refers to the
absence of an optical signal.
Indicator LEDs and Alarm Circuitry
The stand-alone box versions of the Pure Digital Fiberlink 7030 and
7040 Series transmission units have integral LEDs that are used to
monitor the state of the unit. There are two video LEDs on the 7030
units and four video LEDs on the 7040 units. The LEDs are labeled
VID 1, VID 2, VID 3 and VID 4.
The rack card versions of this units have an additional red indicator
LED that lights when an alarm condition exists. The rack card unit also
provides an output to drive a model 6020A Alarm Sensing Module
which provides an audible tone and activates a set of contacts for
external signaling purposes.
TRANSMITTER and RECEIVER:
Power: (Green) Indicates that correct power has been applied.
TRANSMITTER:
Video: OFF: Indicates no video detected on input BNC connector
ON: Indicates video detected on input BNC connector
Alarm: ON: Loss of video (rack card only)
5
INSTALLATION INSTRUCTIONS
Alarm Switch Settings (Receiver; Card Version Only)
Installation Procedure
The Pure Digital Fiberlink 7030 and 7040 Series transmission
systems are normally preset for immediate use. There are indicator
LEDs on the units for monitoring purposes. The following instructions
describe the typical installation procedure and the function of the LED
indicators.
1. Connect the fiber optic cable or cables
between the two Pure Digital Fiberlink
units.
2. Apply power to both Pure Digital
Fiberlink units. For box versions using
DC power connections, refer to Figure 1.
3. When power is applied, the green
POWER LED will light, indicating the presence of operating power.
The green VIDEO LED(s) will give an indication as stated on the
following page. Note that the rack card version will have an additional red LED to indicate the presence of an alarm condition (loss of
video).
4. The system should now be operational.
Alarm Switch Settings (Transmitter; Card Version Only)
Switch Position
1
2
3
4
5
Alarm Indication
Loss of Link
Loss of Video 1
Loss of Video 2
Loss of Video 3
(7040 only)
Loss of Video 4
(7040 Only)
4
On
Enabled
Enabled
Enabled
Enabled
Off
Disabled
Disabled
Disabled
Disabled
Enabled
Disabled
Switch Position
1
2
3
4
5
Alarm Indication
Loss of Signal
Loss of Video 1
Loss of Video 2
Loss of Video 3
(7040 only)
Loss of Video 4
(7040 Only)
On
Enabled
Enabled
Enabled
Enabled
Off
Disabled
Disabled
Disabled
Disabled
Enabled
Disabled
Note: “Loss of Link” refers to loss of input signal lock. “Loss of Video”
refers to loss of the respective input video. “Loss of Signal” refers to the
absence of an optical signal.
Indicator LEDs and Alarm Circuitry
The stand-alone box versions of the Pure Digital Fiberlink 7030 and
7040 Series transmission units have integral LEDs that are used to
monitor the state of the unit. There are two video LEDs on the 7030
units and four video LEDs on the 7040 units. The LEDs are labeled
VID 1, VID 2, VID 3 and VID 4.
The rack card versions of this units have an additional red indicator
LED that lights when an alarm condition exists. The rack card unit also
provides an output to drive a model 6020A Alarm Sensing Module
which provides an audible tone and activates a set of contacts for
external signaling purposes.
TRANSMITTER and RECEIVER:
Power: (Green) Indicates that correct power has been applied.
TRANSMITTER:
Video: OFF: Indicates no video detected on input BNC connector
ON: Indicates video detected on input BNC connector
Alarm: ON: Loss of video (rack card only)
5
RECEIVER:
Video:
OFF: Indicates no video detected over fiber and, as a result,
no video present on output BNC
ON: Indicates video detected over fiber and, as a result,
video present on output BNC
Alarm: ON: Loss of input video or optical signal (rack card only)
OPERATING POINTERS AND TROUBLESHOOTING
Optical Fiber:
The 7030 and 7040 Series are available in versions that operate with
most multimode (MM) and single mode (SM) optical fibers. Be certain
that the correct size fiber is being used for the particular transmitter/
receiver combination.
Also be certain that the attenuation and bandwidth of the fiber optic
cable being used is within the range of the system’s loss budget
specifications.
Troubleshooting:
Multimode fiber optic cable contains an optical fiber with a light
carrying “core” that is only .0025 inches (62.5 microns) in diameter.
Single mode fiber optic cable has an even smaller “core”, only .00032 to
.0004 inches (8-10 microns). This is smaller than a human hair! As a
result, any minute particles of dirt or dust can easily block the fiber
from accepting or radiating light. Therefore, cleanliness is imperative!
Always use the dust caps provided with all optical connectors
whenever they are exposed to air. Also, it is a good idea to gently clean
the tip of an optical connector with a lint-free cloth moistened with
alcohol whenever dust is suspected.
The status of any of the indicator LEDs should provide the first clue
6
Video
Bandwidth ............................ 7 MHz (-3dB)
Input/Output Impedance ...... 75 Ohms
Input/Output Voltage ............ 1 Vp-p nom., 1.1 Vp-p max.
Differential Phase & Gain ..... 0.5o typical; 1.0% typical
Signal-to-Noise Ratio ............ 62 dB CCIR weighted
Signal Connectors ................. BNC
Optical
Operating Wavelength ........... 850 nm, 1310 nm, 1550 nm, MM/SM
Optical Fiber ......................... 62.5/125 microns MM or
.......................................... 8-10/125 microns SM
Optical Connectors ............... ST or FCPC
Wavelength
Loss Budget (in dB)
Distance* (in km)
850 MM
0-20
0-.75
1310 MM
0-25
0-2
1310 SM
0-25
0-60
1550
0-25
0-80
*Note: Distance specifications are only approximate and are not
guaranteed. Operating loss budget must not be exceeded.
Miscellaneous
Operating Temp. Range ........ -35 to +75 degrees C
Operating Power ................... 9 to 24 Volts AC or [email protected] watts (max)
CAUTION! Some versions of the Pure Digital Fiberlink transmitter unit
contain a solid state Laser Diode located within the optical connector.
This device emits invisible infrared electromagnetic radiation which
can be harmful to human eyes. The radiation from this optical connector, if viewed at close range without a fiber optic cable connected to the
optical connector, may be of sufficient intensity to cause instantaneous
damage to the retina of the eye. Direct viewing of this radiation should
be avoided at all times.
3
GENERAL INFORMATION
Introduction
The Pure Digital Fiberlink® 7030 and 7040 Series transmit multiple
channels of uncompressed composite video over a single fiber optic
cable. The 7030 Series (2 channels video) and 7040 Series (4 channels
video) provide 7 MHz bandwidth per video channel and are compatible
with NTSC, PAL and SECAM video standards. Systems are offered
for use with single mode or multimode fiber. With a wide operating
temperature range, the systems are suitable for any indoor or protected
outdoor environment.
Systems consist of two units (transmitter and receiver), each
equipped with indicator LEDs to continuously indicate the presence of
power and video signals. The system is available in box or card
version. Card units fit within the model 6000A card cage.*
Technical Specifications
Model Part Numbering
Configurations:
*Card versions for the
Unit Type
Transmitter Box
Transmitter Card*
Receiver Box
Receiver Card*
Part Number
7030/7040-BXY
7030/7040-CXY
7031/7041-BXY
7031/7041-CXY
X Values:
Y Values:
1 = 850 nm Multimode
S = ST connector
3 = 1310 nm Multimode F = FCPC connector
7 = 1310 nm Single Mode
9 = 1550 nm Single Mode
2
7030 Series fill one
slot in the model
6000A card cage.
Card versions for the
7040 Series fill two
slots.
as to the origin of any operational failure. Be certain that the input and
output signal connections are proper. Due to the number of positions,
Finally, although multimode and single mode devices may look the
same, they will not operate properly together. Using the wrong device
or fiber can easily add more attenuation than specified, resulting in poor
overall performance.
If, after reviewing these possibilities, the system is still not operating, please contact the Customer Service Department for further
assistance. (See page 8 for contact information.)
MAINTENANCE
The Pure Digital Fiberlink 7030 and 7040 Series transmission units
have been manufactured using the latest semiconductor devices and
techniques that electronic technology has to offer. They have been
designed for long, reliable and trouble-free service and are not
normally field repairable. Should difficulty be encountered, Communications Specialties maintains a complete service facility to render
accurate, timely and reliable service of all products.
The only maintenance that can be provided by the user is to
ascertain that optical connectors are free of dust or dirt that could
interfere with light transmission and that electrical connections are
secure and accurate.
All other questions or comments should be directed to our Customer
Service Department. It should be noted that many “problems” can
easily be solved by a simple telephone call.
LIMITED WARRANTY
Communications Specialties, Inc. (CSI) warrants that for a period of
three years after purchase by the Buyer, the Pure Digital Fiberlink
7030 and 7040 Series Transmission Systems will be free from defects
7
in material and workmanship under normal use and service. A Return
Material Authorization (RMA) number must be obtained from CSI at
the expense and risk of the Buyer. CSI’s Obligation under this warranty
will be limited, at its option, to either the repair or replacement of
defective units, including free materials and labor. In no event shall CSI
be responsible for any incidental or consequential damages or loss of
profits or goodwill. CSI shall not be obligated to replace or repair
equipment that has been damaged by fire, war, acts of God, or similar
causes, or equipment that has been serviced by unauthorized personnel,
altered, improperly installed or abused.
RMA numbers and repairs can be obtained from:
Communications Specialties, Inc.
55 Cabot Court
Hauppauge, NY 11788 USA
Tel: (631) 273-0404 Fax: (631) 273-1638
www.commspecial.com
Email: [email protected]
CONTENTS
General Information .................................................... 2
Introduction ............................................................ 2
Technical Specifications .......................................... 2
Installation Instructions .............................................. 4
Installation Procedure ............................................. 4
Alarm Switch Settings ............................................ 4
Indicator LEDs and Alarm Circuitry ...................... 5
Operating Pointers and Troubleshooting .................... 6
Maintenance ............................................................... 7
Or, in the Asia Pacific Region:
Warranty ..................................................................... 7
Communications Specialties Pte Ltd
100 Beach Road
#22-09 Shaw Tower
Singapore 189702
Tel: +65 6391 8790 Fax: +65 6396 0138
Email: [email protected]
Please have your serial number (located on the top label of the unit)
available when contacting us.
8
1
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement