TM-10-3510-226-10-HR

TM-10-3510-226-10-HR
TM 10-3510-226-10-HR
HAND RECEIPT
COVERING
CONTENTS OF COMPONENTS OF END ITEM (COEI),
BASIC ISSUE ITEMS (BII),
AND ADDITIONAL AUTHORIZED LIST (AAL)
CONTAINERIZED BATCH LAUNDRY (CBL)
NSN 3510-01-527-2209
NSN 3510-01-527-2210
DISTRIBUTION STATEMENT A – Approved for public release; distribution is unlimited.
HEADQUARTERS, DEPARTMENT OF THE ARMY
31 AUGUST 2005
TM 10-3510-226-10-HR
HAND RECEIPT
TM 10-3510-226-10-HR
DEPARTMENT OF THE ARMY
WASHINGTON, D.C., 31 August 2005
HAND RECEIPT
COVERING
CONTENTS OF COMPONENTS OF END ITEM (COEI),
BASIC ISSUE ITEMS (BII),
AND ADDITIONAL AUTHORIZED LIST (AAL)
CONTAINERIZED BATCH LAUNDRY (CBL)
NSN 3510-01-527-2209
NSN 3510-01-527-2210
REPORTING ERRORS AND RECOMMENDING IMPROVEMENTS
You can help improve this manual. If you find any mistakes or if you know of a way to improve the
procedures, please let us know. Mail your letter together with DA Form 2028 (Recommended Changes
to Publications and Blank Forms), located in the back of this manual, direct to: Commander, U.S. Army
Tank-automotive & Armaments Command, ATTN: AMSTA-LC-CECT, Kansas Street, Natick, MA
01760-5052. You may also send in your recommended changes via electronic mail directly to
amssbriml @natick.army.mil. A reply will be furnished to you. Instructions for sending an electronic
2028 may be found at the back of this manual immediately preceding the hard copy 2028.
DISTRIBUTION STATEMENT A. – Approved for public release. Distribution is unlimited.
TABLE OF CONTENTS
PAGE
Section I. INTRODUCTION...............................................................................................................ii
Section II. HAND RECEIPT.............................................................................................................. 1
i
TM 10-3510-226-10-HR
Section I. INTRODUCTION
1. Scope
This publication provides an overprinted DA Form 2062 (Hand Receipt) which lists the contents of Components of End
Item (COEI), Basic Issue Items (BII), and Additional Authorization List (AAL) items related to the Containerized Batch
Laundry (CBL).
2. General
a.
Section II is the overprinted DA Form 2062 which lists the line item entry for system/end item and the content of
COEI and BII extracted from TM 10-3510-226-10. The listings consist of exactly the same items and are in the
same sequence as those listings in TM 10-3510-226-10.
b.
The overprinted DA Form 2062 will eliminate manual preparation of the form and will assist organizations in
inventorying and accounting for property as required by AR 710-2.
c.
Local reproduction of the overprinted DA Form 2062 is authorized. However, organizations will comply with local
policies in the reproduction of DA Form 2062 by office copying equipment, field printing plant, or duplicating plant
facilities.
d.
Additional copies of this publication may be requisitioned from the U.S. Army Publications Distribution Center,
1655 Woodson Road, St. Louis, MO. 63114-6181, in accordance with procedures in Chapter 12, DA PAM 25-33.
3. Explanation of Blocks and Columns (DA Form 2062) Refer to DA Pam 710-2-1, Chapter 6 for additional
information required to complete DA Form 2062.
a.
FROM. Enter the organization, unit section or squad which issues the property.
b.
TO. Enter the Unit Identifier Code (UIC) and the hand receipt file number of the unit/personnel receiving the
property.
c.
HAND RECEIPT NUMBER. Enter a locally designated number. Use it to post the location of property in the
property book.
d.
END ITEM STOCK NUMBER. Contains the National Stock Number (NSN) to the end item covered by the hand
receipt.
e.
END ITEM DESCRIPTION. Contains the end item short title.
f.
PUBLICATION NUMBER. Contains the TM number of the technical manual containing the operator/crew
instructions for the equipment.
g.
PUBLICATION DATE. Date of the operator/crew technical manual.
h.
QUANTITY. Quantity of the end item covered by this hand receipt.
i.
STOCK NUMBER. (Column a). National stock number of the item described. Items without stock numbers should
be requisitioned by Commercial and Government Entity Code (CAGEC) and part number with exception data in
accordance with AR 710-2
ii
TM 10-3510-226-10-HR
j.
ITEM DESCRIPTION (Column b). Enter a description of the item, to include the make or model and the serial/USA
number, followed by the item description of COEI and BII items. In addition, it will contain the 5-digit Commercial and
Government Entity Code (CAGEC), Part Number (P/N), and “Used On Code”. The “Used On Code” will not be used in
this manual.
k.
ARC (Column c). The Accounting Requirements Code (ARC) is provided here. One of the following ARC will apply:
NOTE
The Accounting Requirements Code (ARC) refers to property accountability, not the Recoverability
Code (RC). The ARC and the RC are listed in the Army Master Data File (AMDF).
l.
(N) for Nonexpendable
Items not consumed in use, retaining
their identity during use and requiring
accountability be maintained
throughout the life of the item.
(D) for Durable
Nonconsumable components of sets,
kits, outfits and assemblages; all tools
in FSCs 5120, 5130, 5140, 5180,
5210, 5220, and 5280; and any other
nonconsumable with a price in excess
of $50.00 or less and not already “N”.
(X) for Expendable
Items, regardless of type classification
or price and which is consumed in
use. Includes all class 9 repair parts.
Items not consumed in use which cost
$50.00 or less and not already “N” or
“D”.
SEC (Column d). The Controlled Inventory Item Code (formerly SEC code) is entered here. This is a one-position
code which indicates the security classification, security risks or pilferage controls required for storage or
transportation of assets. Order of precedence of assignment codes is classified, sensitive, pilferable, unclassified,
as applicable. Codes applicable to this hand receipt are as follows:
iii
TM 10-3510-226-10-HR
SEC CODE
PHYSICAL SECURITY CODE
A
CONFIDENTIAL – Former Restricted Data
B
CONFIDENTIAL – Restricted Data
C
CONFIDENTIAL
D
CONFIDENTIAL – Cryptologic
E
SECRET – Cryptologic
F
TOP SECRET – Cryptologic
G
SECRET – Former Restricted Data
H
SECRET – Restricted data
K
TOP SECRET – Former Restricted Data
L
TOP SECRET – Restricted Data
O
Naval Nuclear Propulsion Information
S
SECRET
T
TOP SECRET
SEC CODE
P
Q
7
SEC CODE
M
N
V
W
X
Y
Z
SENSITIVE ITEMS CODE
Ammunition and Explosives
An item which is a drug or other substance determined by the Director, Drug Enforcement
Administration (DEA), Department of Justice, to be designated schedule symbol III, IV or V, as
defined in the Controlled Substance Act of 1970, and other items requiring vault storage.
Sensitive information, prior to disposal, all nameplates, label plates, tags, stickers, documents or
markings, which relate items to weapons system end item application, must be removed and
destroyed.
PILFERABLE ITEMS CODE
Aircraft engine equipment and parts
Hand tools and shop equipment
Firearms
Individual clothing and equipment
Office machines
Photographic equipment and supplies
Communications/electronic equipment and parts
Vehicular equipment and parts. Pilferable item, due to its size, shape and utility, which does not
fall under one of the above categories. Pilferage controls may be designated by the coding
activity to items coded U (unclassified) by recoding the items to J.
m. UI (Column e). Unit of Issue. Refer to AR 708-1 and/or CDA PAM 18-1 (Catalog Data Activity) for explanation
of abbreviations used in this column.
iv
TM 10-3510-226-10-HR
n. QTY AUTH (Column f). The quantity authorized to be on hand, or part of the end item.
o. Quantity (Column g). Actual quantity on hand. To be filled in by the receiving unit/personnel.
p. Page of
Pages. Contains page number and total number of pages for the COEI, BII, and AAL portions of the hand
receipt. Hand Receipt holder will initial each page number (only when two or more forms are involved). When hand receipt
holders change, the old initials will be lined out, and the new hand receipt holder will initial each page.
4. Authorization Documents
a. Components of End Item (COEI) are authorized by the applicable Repair Parts and Special Tools List (RPSTL).
b. Basic Issue Items (BII) are authorized by the applicable operator’s manual.
c.
Additional Authorization List (AAL) items are authorized by the appropriate MTOE, TDA, CTA, or JTA authorization
documents.
Section II. HAND RECEIPT
Following is the Hand Receipt for the Containerized Batch Laundry (CBL).
v/(vi Blank)
CONTAINERIZED BATCH LAUNDRY (CBL)
HAND RECEIPT/ANNEX NUMBER
For use of this form, see DA PAM 710-2-1.
The proponent agency is ODCSLOG.
FOR
END ITEM STOCK NUMBER
ANNEX/CR
ONLY
3510-01-527-2209
3510-01-527-2210
STOCK NUMBER
FROM:
TO:
HAND RECEIPT
NUMBER
CONTAINERIZED BATCH LAUNDRY
a.
b.
1
31 AUGUST 05
TM 10-3510-226-10
ITEM DESCRIPTION
*
c.
QUANTITY
PUBLICATION
DATE
PUBLICATION NUMBER
END ITEM DESCRIPTION
SEC
d.
UI
e.
QTY
AUTH
f.
g.
A
QUANTITY
B
C
D
E
F
COMPONENTS OF END ITEM (COEI)
4120-01-449-0459
AIR COND 66000 BTU
(94833) 9454100
N
U
EA
1
4520-01-367-2739
HEATER 12000 BTU PORT
(90598) H120
N
U
EA
1
5430-01-470-7380
TANK, FABRIC, COLLAPSIBLE
(05YK6) RCF-3K-W-OT
N
U
EA
2
HAND RECEIPT, enter Hand Receipt Annex Number
HAND RECEIPT FOR QUARTERS FURNITURE, enter Condition Codes
HAND RECEIPT ANNEX/COMPONENTS RECEIPT; enter Accounting Requirements Code (ARC).
DA FORM 2062, JAN 82
EDITION OF JAN 58 IS OBSOLETE
CURRENT AS OF: 31 AUGUST 2005
PAGE ___1___ OF __10___ PAGES
USAPPC V2.10
1
TM 10-3510-226-10-HR
* WHEN USED AS A:
a.
ITEM DESCRIPTION
b.
*
c.
QTY
AUTH
SEC
d.
UI
e.
N
U
EA
1
X
U
EA
2
X
U
EA
1
X
U
EA
1
N
U
EA
1
N
U
EA
3
N
U
EA
3
N
U
EA
1
N
U
EA
1
N
U
EA
1
N
U
EA
1
N
U
EA
1
N
U
EA
4
f.
g.
A
QUANTITY
B
C
D
E
F
BASIC ISSUE ITEMS LIST (BII)
4510-01-214-9139
8415-00-082-6108
7920-01-503-1671
7920-01-531-0637
6150-01-247-4781
6150-01-220-5587
6150-01-256-6301
7240-01-337-5269
OR
7240-01-337-5268
7240-00-160-0441
4310-01-531-0626
6150-01-516-2050
ADAPTER ASSEMBLY (Fuel Drum Adapter)
(81337) 618285
APRON IMPERMEABLE
(58536) A-A-55063
BROOM, PUSH
(83421) 7920-00-NIB-0322
BRUSH, SANITARY
(39428) 9756T23
CABLE ASSEMBLY (50-ft 60-AMP)
(97403)13226E7023-2
CABLE ASSEMBLY (50-ft 100-Amp)
(81349) MIL-C-29184
CABLE PIGTAIL (4-ft 100-Amp)
(97403)13226E7019
CAN, GASOLINE, MILITARY (Olive Drab)
(81349) A-A-59592
OR
CAN, GASOLINE, MILITARY (sand)
(81349) A-A-59592
CAN, TRASH AND GARBAGE
(39428) 9793506
CIRCUIT BREAKER PANEL ACCESS KEY
(56365) LP9618
COMPRESSOR, UNIT RECIPROCATING
(68821) CPFA2600P
CORD EXTENSION (Extension Cord, 50-ft)
(45152) 3375000
Reverse of DA Form 2062
USAPPC V2.10
CURRENT AS OF: 31 AUGUST 2005
PAGE ____2___ OF _____10___ PAGES
TM 10-3510-226-10-HR
2
CONTAINERIZED BATCH LAUNDRY (CBL)
STOCK NUMBER
CONTAINERIZED BATCH LAUNDRY (CBL)
STOCK NUMBER
ITEM DESCRIPTION
a.
b.
QTY
AUTH
*
c.
SEC
d.
UI
e.
N
U
EA
1
N
U
EA
1
X
U
EA
1
X
U
EA
1
f.
g.
A
QUANTITY
B
C
D
E
F
(BII)-CONTINUED
7240-00-161-1147
7290-00-616-0109
6515-01-457-0631
COVER, CAN TRASH AND GARGABE (32 Gallon, Gray)
(39428) 9793514
DRYER KEY
(59618) 70155601
DUST PAN
(58536) A-A-300
FACE SHIELD HEAD GEAR (Double Matrix)
(39428) 11618
FACE SHIELD PROTECTION GUARD
(1AG17) 76-1564-11
X
U
EA
1
4210-00-889-2491
FIRE EXTINGUISHER, 10-lb
(80244) A-A-393, TY 1, CL 1, SZ10
N
U
EA
1
3990-01-531-0622
FIXTURE ASSEMBLY, STACKING
(0U5N7) 43261127-2
N
U
EA
1
OR
OR
3990-01-531-1958
FIXTURE ASSEMBLY, STACKING
(0U5N7) 43261127-1
N
U
EA
1
U
EA
1
U
BX
1
U
BX
1
U
EA
2
U
EA
2
U
EA
2
U
EA
4
FUNNEL, 32 OUNCE
(39428) 89011616
X
8415-01-463-5928
GLOVES, NATURAL RUBBER, SIZE MED/LG
(39428) 23170ML
X
8415-01-463-5922
GLOVES, NATURAL RUBBER, SIZE SM/MED
(39428) 23170SM
X
8415-00-266-8677
GLOVES, RUBBER, SIZE 10
(39428) 680-10
X
8415-00-266-8675
GLOVES, RUBBER, SIZE 11
(39428) 6680-11
X
8415-00-266-8679
GLOVES, RUBBER, SIZE 9
(39428) 6680-9
X
4240-00-269-7912
GOGGLES, INDUSTRIAL
(39428) 6636
7240-00-527-9868
Reverse of DA Form 2062
X
USAPPC V2.10
3
CURRENT AS OF: 31 AUGUST 2005
PAGE _____3____ OF ___10_ PAGES
TM 10-3510-226-10-HR
3510-01-531-0617
ITEM DESCRIPTION
a.
b.
QTY
AUTH
*
c.
SEC
d.
UI
e.
4520-01-530-8693
HEATING ELEMENT ELECTRICAL, IMMERSION TYPE
(81337) AP15N
N
U
EA
2
4720-00-077-0905
HOSE, ASSEMBLY, FUEL (1 Supply, 1 Return)
(0U5N7) 43261146
N
U
EA
2
N
U
EA
1
N
U
EA
1
N
U
EA
2
N
U
EA
1
INSULATED LINER for 3000-GALLON WATER TANK
(Top/Bottom Section)
N
U
EA
2
INSULATED LINER for 3000-GALLON WATER TANK (Left
Side Section)
(81337) 9-1-0829-GRN
N
U
EA
1
INSULATED LINER for 3000-GALLON WATER TANK (Left
Side Section)
(0U5N7) 9-1-0829-TAN
N
U
EA
1
INSULATED LINER for 3000-GALLON WATER TANK (Right
Side Section)
(81337) 9-1-0828-TAN
N
U
EA
1
INSULATED LINER for 3000-GALLON WATER TANK (Right
Side Section)
(81337) 9-1-0828-GRN
N
U
EA
2
LENS, GOGGLES, INDUSTRIAL
(80204) ANSI-1
X
U
EA
4
f.
g.
A
QUANTITY
B
C
D
E
F
(BII)-CONTINUED
4720-01-531-0616
4720-01-531-0620
4720-01-531-0621
HOSE ASSEMBLY, NONMETALLIC
(0U5N7) 43261150
HOSE ASSEMBLY, NONMETALLIC
(0U5N7) 43261151
HOSE ASSEMBLY, NONMETALLIC (20-ft length, 2-in.
diameter) (0U5N7) 43261152
INSULATED LINER for 3000-GALLON WATER TANK
GREEN (Top/Bottom Section) (81337)
OR
OR
OR
4240-00-262-7092
Reverse of DA Form 2062
USAPPC V2.10
CURRENT AS OF: 31 AUGUST 2005
PAGE ____4____ OF __10___ PAGES
TM 10-3510-226-10-HR
4
CONTAINERIZED BATCH LAUNDRY (CBL)
STOCK NUMBER
CONTAINERIZED BATCH LAUNDRY (CBL)
STOCK NUMBER
ITEM DESCRIPTION
a.
b.
QTY
AUTH
*
c.
SEC
d.
UI
e.
N
U
EA
2
N
U
BX
1
N
U
EA
1
N
U
EA
1
X
U
EA
1
D
U
EA
1
N
U
EA
1
N
U
EA
1
N
U
EA
2
N
U
EA
2
N
U
EA
1
N
U
EA
1
N
U
EA
2
N
U
EA
2
D
U
EA
1
f.
g.
A
QUANTITY
B
C
D
E
F
(BII)-CONTINUED
6230-01-397-1428
4240-01-247-2348
7330-00-205-3096
5120-01-354-2770
5340-01-531-1962
OR
5340-01-531-1963
5340-01-531-0618
5340-01-531-0619
5340-01-531-1959
5340-01-531-1960
5120-00-060-2004
Reverse of DA Form 2062
USAPPC V2.10
CURRENT AS OF: 31 AUGUST 2005
PAGE ____5____ OF __10___ PAGES
TM 10-3510-226-10-HR
5975-00-878-3791
LIGHT, EXTENSION
(00L99) ACS-2425PL
MASK, AIR FILTERING
(50378) 8511N95
MEASURE, LIQUID
(58536) A-A-1751
MOUNTING BASE PLATE
(OU5N7) 43261106
MSDS BOOK
(0U5N7) 43269009
NUT DRIVER (Solid Shaft, 5/16 in.)
(33287) J-35993-5
PLATE, MOUNTING (End Plate Stacking Feature, Green)
(0U5N7) 43262251-1
OR
PLATE, MOUNTING (End Plate Stacking Feature, Tan)
(0U5N7) 43262251-2
PLATE MOUNTING (Foot, Interface, FDECU)
(0U5N7) 43262117
PLATE MOUNTING (Removable End Plate Stacking Fixture,
FDECU)
(0U5N7) 43262270
PLATE, MOUNTING (Tie-Down Offset Anchor Clamp for
FDECU)
(0U5N7) 43262297
PLATE, MOUNTING (Tie-Down Offset Slide Clamp for
FDECU)
(0U5N7) 43262296
RAMP SECTIONS
(0U5N7) 43262134-3
ROD, GROUND (SECT, Type III, Class B)
(81348) W-R-550
SCREWDRIVER, PHILLIPS Tip, SIZE #1,
(39428) 84959329
5
ITEM DESCRIPTION
a.
b.
QTY
AUTH
*
c.
SEC
d.
UI
e.
SCREWDRIVER, STANDARD TIP
(39428) 84959162
D
U
EA
1
5120-00-288-8739
SCREWDRIVER SET, JEWELER’S SWIVEL
(33164) 250
D
U
EA
1
7340-00-240-7079
SPOON, FOOD SERVICE
(58536) A-A-1082
N
U
EA
1
6110-01-242-6691
STAND, DISTRIBUTION (BOX, TEMPER)
(81337) 1-6-6005
N
U
EA
1
5430-00-134-3196
STRAP WEBBING (cargo strap small)
(19207) 8690494
X
U
EA
10
7110-01-415-6895
TABLE, FOLDING
(81337) 623954
N
U
EA
4
8340-01-240-5854
TEMPER, ARCH ASSEMBLY
(81337) 5-4-4006
N
U
EA
3
8340-01-186-3030
TEMPER, CONTAINER TENT PIN
(81337) 5-4-8487-1
N
U
EA
1
8340-01-186-3029
TEMPER, CONTAINER, VESTIBULE
(81337) 5-4-3374-1
N
U
EA
1
6150-01-470-1916
TEMPER, CONVENIENCE OUTLET, DUPLEX w/GFCI
(81337) 9-1-0624-1
N
U
EA
4
8340-01-186-3013
TEMPER, COVER, TENT FRAME
(81337) 5-4-3347-1
N
U
EA
1
8340-01-186-3009
TEMPER, EAVE EXTENDER
(81337) 5-4-3341
N
U
EA
6
6110-01-251-0402
TEMPER, ELECTRIC DISTRIBUTION BOX
(81337) 1-6-6041
N
U
EA
1
f.
g.
A
QUANTITY
B
C
D
E
F
(BII)-CONTINUED
5120-00-142-5279
Reverse of DA Form 2062
USAPPC V2.10
CURRENT AS OF: 31 AUGUST 2005
PAGE ____6____ OF ___10__ PAGES
TM 10-3510-226-10-HR
6
CONTAINERIZED BATCH LAUNDRY (CBL)
STOCK NUMBER
CONTAINERIZED BATCH LAUNDRY (CBL)
STOCK NUMBER
ITEM DESCRIPTION
a.
b.
QTY
AUTH
*
c.
SEC
d.
UI
e.
N
U
EA
1
N
U
EA
1
N
U
EA
1
N
U
EA
1
N
U
EA
2
N
U
EA
2
N
U
EA
1
N
U
EA
1
N
U
EA
1
N
U
EA
3
N
U
ST
1
N
U
EA
1
N
U
EA
10
N
U
EA
3
N
U
EA
2
f.
g.
A
QUANTITY
B
C
D
E
F
(BII)-CONTINUED
8340-01-186-3014
OR
8340-01-198-7618
OR
8340-01-186-3025
8340-01-186-3024
8340-01-186-3027
8340-01-186-3018
OR
8340-01-198-5358
8340-01-186-3004
6230-01-465-8931
8340-01-211-6798
8340-01-186-3005
8465-01-220-1419
Reverse of DA Form 2062
USAPPC V2.10
7
CURRENT AS OF: 31 AUGUST 2005
PAGE ____7____ OF __10___ PAGES
TM 10-3510-226-10-HR
8340-01-186-3008
TEMPER, END SECTION, ISO
(81337) 5-4-3350-1
OR
TEMPER, END SECTION, ISO
(81337) 5-4-3350-2
TEMPER, END SECTION, MODIFIED ISO
(81337) 9-1-0586
OR
TEMPER, END SECTION, MODIFIED ISO
(81337) 9-1-0586
TEMPER, FLOOR, INSULATED
(81337) 5-4-3369
TEMPER, FLOOR, TENT
(81337) 5-4-3368-1
TEMPER, FLOOR, TENT, VESTIBULE
(81337) 5-4-3372-1
TEMPER, FLY, TENT
(81337) 5-4-3353-1
OR
TEMPER, FLY, TENT
(81337) 5-4-3353-2
TEMPER, HEADER ASSEMBLY
(81337) 5-4-3335
TEMPER, LIGHT SET, GENERAL ILLUMINATION, ISO
(06967) F131-5004M
TEMPER, PLENUM, TENT
(81337) 5-4-3620
TEMPER, PURLIN ASSEMBLY
(81337) 5-4-3336
TEMPER, RIDGE EXTENDER
(81337) 5-4-3340
TEMPER, STRAP, LIGHT SUPPORT ASSEMBLY, TYPE I,
ISO
(81337) 5-4-4005
ITEM DESCRIPTION
a.
b.
QTY
AUTH
*
c.
SEC
d.
UI
e.
N
U
EA
4
N
U
EA
6
N
U
EA
4
N
U
EA
8
N
U
EA
1
N
U
EA
1
N
U
EA
30
N
U
EA
15
N
U
EA
3
N
U
EA
1
N
U
EA
1
N
U
EA
1
N
U
EA
2
N
U
EA
2
N
U
EA
5
f.
g.
A
QUANTITY
B
C
D
E
F
(BII)-CONTINUED
8340-01-392-0921
OR
8340-01-213-9566
8340-00-823-7451
8340-00-261-9751
8340-01-186-3010
8340-01-186-3026
OR
8340-01-198-7621
8340-01-186-3021
OR
8340-01-198-7619
3990-01-204-3009
TEMPER, TENT LINE, ENDWALL
(81337) 5-4-3350-1-36
TEMPER, TENT LINE, TENT FLY
(81337) 5-4-3353-1-26
TEMPER, TENT LINE, VESTIBULE
(81337) 5-4-3370-1-20
TEMPER, TENT LINE, WINDOW SECTION
(81337) 5-4-3363-1-32
TEMPER, TENT LINER, END SECTION TEMPERATE,
GREEN
(81337) MIL-T-44243
OR
TEMPER, TENT LINER, END SECTION TEMPERATE,
TROPICAL DESERT
(81337) MIL-T-44243
TEMPER, TENT PIN, STEEL, 12-in., ISO
(81337) 5-4-791
TEMPER, TENT PIN, Wood, 24-in., ISO
(81337) 5-4-1
TEMPER, VESTIBULE FRAME ASSEMBLY
(81337) 5-4-3343
TEMPER, VESTIBULE, TENT
(81337) 5-4-3370
OR
TEMPER, VESTIBULE, TENT
(81337) 5-4-3371
TEMPER, WINDOW SECTION, ISO
(81337) 5-4-3363-1
OR
TEMPER, WINDOW SECTION, ISO
(81337) 5-4-3363-2
TIE DOWN, CARGO (cargo strap large)
(98313) FDC5770-5
Reverse of DA Form 2062
USAPPC V2.10
CURRENT AS OF: 31 AUGUST 2005
PAGE ____8____ OF __10___ PAGES
TM 10-3510-226-10-HR
8
CONTAINERIZED BATCH LAUNDRY (CBL)
STOCK NUMBER
CONTAINERIZED BATCH LAUNDRY (CBL)
STOCK NUMBER
ITEM DESCRIPTION
a.
b.
*
c.
QTY
AUTH
SEC
d.
UI
e.
N
U
EA
1
TM 10-3510-226-10-HR
N
U
EA
1
TM 10-3510-226-23
N
U
EA
1
TM 10-3510-226-23P
TRANSFER TOP, LAUNDRY CART
(0U5N7) 43262305
TRK 37-1/2x26x291/2
(81349) A-A-50025
TRUNK, LOCKER TYPE II
(58536) A-A-59490
WASHER CONTROL PANEL ACCESS KEY
(59618) F160562
WASHER PROGRAM KEY
(59618) 9001756
WRENCH, ADJUSTABLE (10”, CHROME, CRESCENT,
15/16 IN. CAPACITY)
(39428) W-72
WRENCH, STRAP LARGE SIZE 6 3/8 IN. DIA
(39428) 54325A24
N
U
EA
1
N
U
EA
1
N
U
EA
2
N
U
EA
1
N
U
EA
1
N
U
EA
1
D
U
EA
1
D
U
EA
1
f.
g.
A
QUANTITY
B
C
D
E
F
(BII)-CONTINUED
TM 10-3510-226-10
3920-00-929-8588
8460-01-471-1035
5120-00-278-0341
5120-01-461-1810
USAPPC V2.10
CURRENT AS OF: 31 AUGUST 2005
PAGE ____9____ OF ___10__ PAGES
TM 10-3510-226-10-HR
Reverse of DA Form 2062
9
ITEM DESCRIPTION
a.
b.
*
c.
QTY
AUTH
SEC
d.
UI
e.
X
U
EA
6
X
U
PR
2
X
U
EA
2
D
U
EA
1
f.
g.
A
QUANTITY
B
C
D
E
F
ADDITIONAL AUTHORIZED LIST (AAL)
7920-00-772-5800
8415-00-753-6552
4240-00-190-6432
5120-00-926-7116
BRUSH, SANITARY
(58536) A-A-3069
GLOVES, TAP TYPE2 M10
(81349) MIL-G-12223
GOGGLES INDUSTRIAL
(58536) A-A-1110
MALLET, WOOD (6-in. FACE X 8-in. Long Head
(80244) LLL-M-71 TY9
Reverse of DA Form 2062
USAPPC V2.10
CURRENT AS OF: 31 AUGUST 2005
PAGE ___10____ OF ____10__ PAGES
TM 10-3510-226-10-HR
10
CONTAINERIZED BATCH LAUNDRY (CBL)
STOCK NUMBER
ARMY TM 10-3510-226-10-HR
By Order of the Secretary of the Army:
PETER J. SCHOOMAKER
General, United States Army
Chief of Staff
Official:
SANDRA R. RILEY
Administrative Assistant to the
Secretary of the Army
0522402
Distribution: To be distributed in accordance with initial distribution number (IDN) 256846 requirements for TM
10-3510-226-10-HR.
These are the instructions for sending an electronic 2028
The following format must be used if submitting an electronic 2028. The subject
line must be exactly the same and all fields must be included; however only the
following fields are mandatory: 1, 3, 4, 5, 6, 7, 8, 9, 10, 13, 15, 16, 17, and 27.
From: "Whomever" <whomever@avma27.army.mil>
To:
amssbriml@natick.army.mil
Subject:
DA Form 2028
1.
From: Joe Smith
2.
Unit: home
3.
Address: 4300 Park
4.
City: Hometown
5.
St: MO
6.
Zip: 77777
7.
Date Sent: 19-OCT-93
8.
Pub no: 55-2840-229-23
9.
Pub Title: TM
10.
Publication Date: 04-JUL-85
11.
Change Number: 7
12.
Submitter Rank: MSG
13.
Submitter FName: Joe
14.
Submitter MName: T
15.
Submitter LName: Smith
16.
Submitter Phone: 123-123-1234
17.
Problem: 1
18.
Page: 2
19.
Paragraph: 3
20.
Line: 4
21.
NSN: 5
22.
Reference: 6
23.
Figure: 7
24.
Table: 8
25.
Item: 9
26.
Total: 123
27.
Text:
This is the text for the problem below line 27.
These are the instructions for sending an electronic 2028
The following format must be used if submitting an electronic 2028. The subject
line must be exactly the same and all fields must be included; however only the
following fields are mandatory: 1, 3, 4, 5, 6, 7, 8, 9, 10, 13, 15, 16, 17, and 27.
From: "Whomever" <whomever@avma27.army.mil>
To:
amssbriml@natick.army.mil
Subject:
DA Form 2028
1.
From: Joe Smith
2.
Unit: home
3.
Address: 4300 Park
4.
City: Hometown
5.
St: MO
6.
Zip: 77777
7.
Date Sent: 19-OCT-93
8.
Pub no: 55-2840-229-23
9.
Pub Title: TM
10.
Publication Date: 04-JUL-85
11.
Change Number: 7
12.
Submitter Rank: MSG
13.
Submitter FName: Joe
14.
Submitter MName: T
15.
Submitter LName: Smith
16.
Submitter Phone: 123-123-1234
17.
Problem: 1
18.
Page: 2
19.
Paragraph: 3
20.
Line: 4
21.
NSN: 5
22.
Reference: 6
23.
Figure: 7
24.
Table: 8
25.
Item: 9
26.
Total: 123
27.
Text:
This is the text for the problem below line 27.
RECOMMENDED CHANGES TO PUBLICATIONS AND
BLANK FORMS
Use Part II (reverse) for Repair Parts and Special Tool
Lists (RPSTL) and Supply Catalogs/Supply Manuals
(SC/SM).
DATE
21 October 2003
For use of this form, see AR 25-30; the proponent agency is ODISC4.
FROM: (Activity and location) (Include ZIP Code)
TO: (Forward to proponent of publication or form) (Include ZIP Code)
US ARMY TANK AUTOMOTIVE AND ARMAMENT
COMMAND
ATTN: AMSTA-LC-CECT
15 KANSAS ST
NATICK, MA 01760-5052
PFC JANE DOE
Co A 3RD Engineer Br.
Ft Leonard Wood, MO 63108
PART I – ALL PUBLICATIONS (EXCEPT RPSTL AND SC/SM) AND BLANK FORMS
PUBLICATION/FORM NUMBER
DATE
TITLE
TM 10-1670-296-23&P
30 October 2002
Unit Manual for Ancillary Equipment for Low Velocity Air
Drop Systems
ITEM
NO.
PAGE
NO.
PARAGRAPH
LINE
NO. *
0036 00-2
FIGURE
NO.
TABLE
NO.
1
RECOMMENDED CHANGES AND REASON
(Provide exact wording of recommended changes, if possible).
In Table 1, Sewing Machine Code Symbols, the second sewing machine code
symbol should be MDZZ not MD22
Change the manual to show Sewing Machine, Industrial: Zig-Zag; 308 stitch;
medium-duty; NSN 3530-01-181-1421 as a MDZZ code symbol.
*Reference to line numbers within the paragraph or subparagraph.
TYPED NAME, GRADE OR TITLE
TELEPHONE EXCHANGE/AUTOVON, PLUS
EXTENSION
SIGNATURE
Jane Doe, PFC
(508) 233-4141
DSN 256-4141
Jane Doe Jane Doe
DA FORM 2028, FEB 74
REPLACES DA FORM 2028, 1 DEC 68, WHICH WILL BE USED.
USAPPC V3.00
TO: (Forward direct to addressee listed in publication)
FROM: (Activity and location) (Include ZIP Code)
DATE
US ARMY TANK AUTOMOTIVE AND ARMAMENT
COMMAND
ATTN: AMSTA-LC-CECT
15 KANSAS ST
NATICK, MA 01760-5052
PFC JANE DOE
Co A 3RD Engineer Br.
Ft Leonard Wood, MO 63108
21 October 2003
PART II – REPAIR PARTS AND SPECIAL TOOL LISTS AND SUPPLY CATALOGS/SUPPLY MANUALS
PUBLICATION NUMBER
DATE
TITLE
TM 10-1670-296-23&P
30 October 2002
Unit Manual for Ancillary Equipment for Low
Velocity Air Drop Systems
COLM
NO.
PAGE
NO.
LINE
NO.
0066 00-1
PART III – REMARKS
TYPED NAME, GRADE OR TITLE
NATIONAL STOCK
NUMBER
REFERENCE
NO.
FIGURE
NO.
4
ITEM
NO.
TOTAL NO.
OF MAJOR
ITEMS
SUPPORTED
RECOMMENDED ACTION
Callout 16 in figure 4 is pointed to a D-Ring.In
the Repair Part List key for Figure 4, item 16
is called a Snap Hook. Please correct one or
the other.
(Any general remarks or recommendations, or suggestions for improvement of publications and
blank forms. Additional blank sheets may be used if more space is needed.)
TELEPHONE EXCHANGE/AUTOVON, PLUS EXTENSION
SIGNATURE
UASPPC V3.00
RECOMMENDED CHANGES TO PUBLICATIONS AND
BLANK FORMS
Use Part II (reverse) for Repair Parts and Special Tool
Lists (RPSTL) and Supply Catalogs/Supply Manuals
(SC/SM).
DATE
For use of this form, see AR 25-30; the proponent agency is ODISC4.
TO: (Forward to proponent of publication or form) (Include ZIP Code)
FROM: (Activity and location) (Include ZIP Code)
Commander
U.S. Army Tank-automotive and Armament Command
ATTN: AMSTA-LC-CECT
Kansas Street, Natick, MA 01760-5052.
PART I – ALL PUBLICATIONS (EXCEPT RPSTL AND SC/SM) AND BLANK FORMS
DATE
31 August 2005
PUBLICATION/FORM NUMBER
TM 10-3510-226-10-HR
ITEM
NO.
PAGE
NO.
PARAGRAPH
LINE
NO. *
FIGURE
NO.
TABLE
NO.
TITLE
Hand Receipt Covering Contents of Component of End
Item (COEI) Basic Issue Items (BII), and Additional
Authorized List (AAL) for Containerized Batch
Laundry(CBL)
RECOMMENDED CHANGES AND REASON
(Provide exact wording of recommended changes, if possible).
*Reference to line numbers within the paragraph or subparagraph.
TYPED NAME, GRADE OR TITLE
DA FORM 2028, FEB 74
TELEPHONE EXCHANGE/AUTOVON, PLUS
EXTENSION
SIGNATURE
REPLACES DA FORM 2028, 1 DEC 68, WHICH WILL BE USED.
USAPPC V3.00
TO: (Forward direct to addressee listed in publication)
FROM: (Activity and location) (Include ZIP Code)
DATE
Commander
U.S. Army Tank-automotive and Armament Command
ATTN: AMSTA-LC-CECT
Kansas Street, Natick, MA 01760-5052.
PART II – REPAIR PARTS AND SPECIAL TOOL LISTS AND SUPPLY CATALOGS/SUPPLY MANUALS
DATE
31 August 2005
PUBLICATION NUMBER
TM 10-3510-226-10-HR
PAGE
NO.
COLM
NO.
LINE
NO.
NATIONAL STOCK
NUMBER
PART III – REMARKS
TYPED NAME, GRADE OR TITLE
REFERENCE
NO.
FIGURE
NO.
ITEM
NO.
TITLE
Hand Receipt Covering Contents of
Component of End Item (COEI) Basic Issue
Items (BII), and Additional Authorized List
(AAL) for Containerized Batch Laundry(CBL)
TOTAL NO.
OF MAJOR
ITEMS
SUPPORTED
RECOMMENDED ACTION
(Any general remarks or recommendations, or suggestions for improvement of publications and
blank forms. Additional blank sheets may be used if more space is needed.)
TELEPHONE EXCHANGE/AUTOVON, PLUS EXTENSION
SIGNATURE
UASPPC V3.00
These are the instructions for sending an electronic 2028
The following format must be used if submitting an electronic 2028. The subject
line must be exactly the same and all fields must be included; however only the
following fields are mandatory: 1, 3, 4, 5, 6, 7, 8, 9, 10, 13, 15, 16, 17, and 27.
From: "Whomever" <whomever@avma27.army.mil>
To:
amssbriml@natick.army.mil
Subject:
DA Form 2028
1.
From: Joe Smith
2.
Unit: home
3.
Address: 4300 Park
4.
City: Hometown
5.
St: MO
6.
Zip: 77777
7.
Date Sent: 19-OCT-93
8.
Pub no: 55-2840-229-23
9.
Pub Title: TM
10.
Publication Date: 04-JUL-85
11.
Change Number: 7
12.
Submitter Rank: MSG
13.
Submitter FName: Joe
14.
Submitter MName: T
15.
Submitter LName: Smith
16.
Submitter Phone: 123-123-1234
17.
Problem: 1
18.
Page: 2
19.
Paragraph: 3
20.
Line: 4
21.
NSN: 5
22.
Reference: 6
23.
Figure: 7
24.
Table: 8
25.
Item: 9
26.
Total: 123
27.
Text:
This is the text for the problem below line 27.
PIN: 082611-000
This fine document...
Was brought to you by me:
Liberated Manuals -- free army and government manuals
Why do I do it? I am tired of sleazy CD-ROM sellers, who take publicly
available information, slap “watermarks” and other junk on it, and sell it.
Those masters of search engine manipulation make sure that their sites that
sell free information, come up first in search engines. They did not create it...
They did not even scan it... Why should they get your money? Why are not
letting you give those free manuals to your friends?
I am setting this document FREE. This document was made by the US
Government and is NOT protected by Copyright. Feel free to share,
republish, sell and so on.
I am not asking you for donations, fees or handouts. If you can, please
provide a link to liberatedmanuals.com, so that free manuals come up first in
search engines:
<A HREF=http://www.liberatedmanuals.com/>Free Military and Government Manuals</A>
– Sincerely
Igor Chudov
http://igor.chudov.com/
– Chicago Machinery Movers
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising