Vivitek User Manual DU8090Z

Vivitek User Manual DU8090Z
User's Manual
DU8090Z
DU8090Z DLP Projector - User Manual
Table of Contents
Copyright ............................................................................................................................................................ 2 Copyright ...................................................................................................................................................... 2 Disclaimer .................................................................................................................................................... 2 About the Manual ......................................................................................................................................... 2 Important Safety Guidelines ............................................................................................................................... 3 Safety Notification ........................................................................................................................................ 3 Installation and Use Notices ......................................................................................................................... 5 Disposal of Old Electric and Electronic Equipment ...................................................................................... 5 Important Recycling Instructions .................................................................................................................. 5 Introduction ......................................................................................................................................................... 6 Packing Checklist ......................................................................................................................................... 6 Projector Overview ....................................................................................................................................... 7 IO Panel ....................................................................................................................................................... 9 Control Panel ............................................................................................................................................. 10 Remote Control .......................................................................................................................................... 11 Installing or Removing the Optional Lens .................................................................................................. 12 Lens Shift Range ........................................................................................................................................ 15 Making Connections ......................................................................................................................................... 17 Connecting to Personal Computer ............................................................................................................. 17 Connecting to the Video Device ................................................................................................................. 17 Connecting to the Control Equipment ........................................................................................................ 18 Connecting to the Screen Trigger .............................................................................................................. 19 Connecting to external HDBaseT Transmitter ............................................................................................ 20 Using the projector............................................................................................................................................ 21 Select the Input Voltage of AC Power ........................................................................................................ 21 Connecting to AC Power Supply ................................................................................................................ 21 Turning on the Projector ............................................................................................................................. 21 Turning off the Projector ............................................................................................................................. 22 Using On-Screen Display ................................................................................................................................. 23 Using the OSD Menu ................................................................................................................................. 23 Menu Tree .................................................................................................................................................. 24 OSD Operation – INPUT ............................................................................................................................ 27 OSD MENU – PICTURE ............................................................................................................................ 30 OSG MENU – ALIGNMENT ....................................................................................................................... 31 OSD MENU – CONTROL .......................................................................................................................... 34 OSD MENU – SERVICE ............................................................................................................................ 37 Product Specification ........................................................................................................................................ 38 Supported Signal Input Timing.......................................................................................................................... 39 Product Dimensions.......................................................................................................................................... 41 LED Indication .................................................................................................................................................. 42 About the VIVITEK Support .............................................................................................................................. 43 1
DU8090Z DLP Projector - User Manual
Copyright
Copyright
The User's Manual (including all pictures, illustrations and software) is protected by the international copyright right
law. All rights are reserved. No duplication of the manual or any content included in the manual is allowed without the
written consent of the manufacturer.
Vivitek is the trademark of Vivitek Corporation. ©All rights reserved. 2016
Disclaimer
The information in the manual is subject to change without notice. The manufacturer does not provide any statement
or warranty of the contents in the manual and clearly give up the implied warranties of merchantability and of fitness
for a particular purpose. The manufacturer reserves the rights to modify the publication and change the contents of
the materials at any time without notice to any person.
About the Manual
The manual describes how to install and use the DLP projector and is applicable to the end-user. Relevant
information (such as illustrations and descriptions) is put on the same page as possible as we can. The format, easy
for printing, is convenient for reading and paper-saving which is beneficial to environmental protection. It is
suggested printing the page you need.
2
DU8090Z DLP Projector - User Manual
Important Safety Guidelines
Thank you for purchasing the high quality product!
Read the Manual carefully to obtain the best performance. The Manual provides instructions to use the menu and
implement operation.
Safety Notification
To turn off main power, ensure to unplug from power outlet.
To prevent electric shock, do not open the cabinet. There are high-voltage components inside.
Refer service to qualified service personnel.
The symbol warns the user about electric shock caused by voltage not insulated. Therefore, it is dangerous
to make any kind of contact with any parts of inside units.
This symbol alerts the user that important information which should be read carefully to avoid problems
concerning the operation and maintenance.
WARNING!
To prevent the projector from electrical discharge or electric shock, do not expose the projector to rain or
moist environment. Do not use the plug with an extension cord or an outlet unless all the prongs can be
fully inserted.
WARNING TO CALIFORNIA RESIDENTS:
Handling the cables supplied with this equipment might expose user to a little lead, a chemical known to the Stage of
California, resulting in risks of barrenness. Please remember to wash hands after handling.
NOTIFICATION (CANADA)
This class A digital equipment complies with Canadian ICES-003.
CE NOTIFICATION
This is a class A product, which complies with rules for CE marking. This product may cause radio interference that
the user may be supposed to take adequate measures.
FCC NOTIFICATION
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference; (2) this device must accept any interference received, including
interference that may cause undesired operation. This equipment has been tested and found to comply with part 15
of the FCC Rules. These requirements are designed to provide reasonable protection against harmful interference
when the equipment operates in a commercial environment. This equipment might generate radio frequency energy.
If user does not install or use in accordance with the instructions in manual, the radio frequency energy may interfere
radio reception. If the above scenario occurs, the user may be responsible to correcting the interference
WARNING!
Changes or modifications without approval from Vivitek could void the user’s authorization to
operate the product.
LIGHT MODULE
 A light module containing multiple laser diodes acts as the light source in the product.
3
DU8090Z DLP Projector - User Manual
 These laser diodes are sealed in the light module. It is recommended to ask dealer for maintenance or repair
services of the light module.
 End user is not allowed to replace the light module.
 Contact distributor who provides the qualified service for light module replacement and further information.
LASER SAFETY NOTIFICATION AND CAUTION
Do not stare at the lens while in use
CLASS 3R LASER PRODUCT
This Laser Product is designated as Class 3R during all procedures of operation.
LASER LIGHT - AVOID DIRECT EYE EXPOSURE.
Do not point laser or allow reflected laser light toward other people or reflective objects.
Direct or scattered light can be hazardous to eyes and skin.
There is a potential hazard of eye exposure to laser radiation if the included instructions are not followed.
Caution – use of controls, adjustments or performance of procedures other than those specified herein may result
in hazardous radiation exposure.
Laser Parameters:
Wavelength
: Maximum laser energy
450nm - 460nm (Blue)
: 0.376mJ
Mode of operation
: Total internal power
Pulsed, due to frame rate
: >100W
Pulse width
: Apparent source size
0.74ms
: >10mm, at lens stop
Pulse repetition rate
: Divergence
24Hz
: >100 mili Radian
Product Label
Manufacturer’s ID Label, Explanatory Label and Certification Statement Label







Hazard Warning Symbol and Aperture Label
4
DU8090Z DLP Projector - User Manual
Installation and Use Notices
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
Read and keep this manual properly.
Pay attention to all the noted warnings, and follow all the guidelines and descriptions in this manual.
Do not use the projector near water.
Do not install the equipment near the thermal sources, such as heaters, radiators, furnace, amplifiers, and any
other equipment that may generate heat.
Be careful while holding the equipment or moving the trolley with projector to prevent the equipment from
turning over.
Notice whether there is any parts with flaws after receiving the projector.
Please notice that the projector will not power on until the lens is fitted. The protection covering the lens should
be taken to install the lens.
Do not let any vent be obstructed.
Do not destroy the safety protection function of polarized or grounding plug of power cord. A polarized plug has
one wide and one narrow blade. The plug has two blades and one grounding blade. The wide blade or
grounding blade is provided for the safety concerns. If the plug provided does not match the outlet, please
contact the electrician to change outlet.
The +12V trigger only outputs 12V DC trigger signal. Do not connect other power input or output. Otherwise,
the equipment may malfunction.
Adjust the slide switch with suitable volt input, and then plug in the projector; the red LED indicator would flash
and then stabilize, getting into standby mode. User should only use the connectors or accessories provided by
the manufacturer.
When user turns on the projector, the red LED indicator would flash until stabilize. Do not look at the lens
directly while the projector is running.
Unplug the power cord of the equipment if there is a thunderstorm or the equipment is not going to be used for
a long time.
The packaging materials can be kept properly for transportation use afterwards.
If any breakdown occurs, please contact dealer or manufacture for qualified repair service.
Disposal of Old Electric and Electronic Equipment
The symbol on your product or the package represents that the product should not be treated as the normal
household waste when discarded but should be carried to the recycling location of the waste electric and electronic
equipment. The consequence on the environment and human health due to the incorrect disposal of the product can
be prevented if it can be ensured that the product is properly discarded. Material recycling is helpful to the protection
of natural resources. The symbol is only valid in European Union. If you want to discard electrical and electronic
equipment, contact the governmental authorities or your dealer for the correct method of disposal.
Important Recycling Instructions
The lamp of the product contains mercury. The product may contain other electronic wastes and may pose risk if not
discarded properly. Abide by the local, state/provincial or federal laws of recycling or discarding. For more
information, please visit the website and contact Electronic Industries Alliance (EIA) on WWW.EIAE.ORG.
Please visit WWW.LAMPRECYCLE.ORG for the specific disposal information of lamps.
5
DU8090Z DLP Projector - User Manual
Introduction
The User's Manual describes the installation, setup and operation of the DU8090Z projector and provides assistance
to the installation personnel and the end-user to fully develop the performance of the projector. VIVITEK has made
every effort to ensure that the information in the Manual is correct at the time of printing. The contents may be
frequently updated due to the continuously product improvement and customer feedback.
You can find the latest version of the Manual and the manual of other Vivitek products on www.vivitekcorp.com.
Packing Checklist
The following items are included in the packaging box of the DU8090Z series projector. If any loss or damage to any
item, contact your dealer or the VIVITEK customer service department.
AC Power Cord Power Cord IR Remote Control (M4) User’s Manual Disc VGA Signal Cable Cable of the Wired Anti‐thief Screw for Remote Control Lens Installation RoHS Card (China) Qualification Certificate (China)
6
DU8090Z DLP Projector - User Manual
Projector Overview
Front-right View
8
1 2
3
4
5
7
6
1. Front IR Receiver
The Receiver for IR signals from remote control.
2. LED Indicator
Display current projector status such as power, light source status
and warning.
3. Air Intake
The fan pulls the cool air to the projector for system cooling.
4. Lens Release Button
Press the Lens Change button before removing the lens.
5. Lens hood
Remove the cover before installing the lens.
6. Height Adjuster
Adjust level of projector
7. Intake Vent
The fans pull air to cool the radiator of the projector.
8. Rear IR Receiver
The Receiver for IR signals from remote control.
Rear-right View
14
10
9
9. I/O Connector Panel
Connect to various input, control or output terminals to the
projector.
10. Kensington Lock
Attach the projector to a permanent object with the Kensington
slot and a security cable.
11. Slide Switch
12. AC Power Switch
Turn on/off the AC power of the projector.
13. AC Inlet
11
Connect the supplied power cable to this inlet.
12 13 14. Control Panel
Press the button to operate the OSD menu or adjust the lens
Settings see OSD controls.
Important:
Grill openings on the projector allow for good air circulation, which keeps the projector lamp cool. Do not obstruct
any of the grill openings
7
DU8090Z DLP Projector - User Manual
Bottom View
15
15.
16
16.
19
17
17.
18.
18
19.
Anti-thief Screw hole
The anti-thief screw can be fastened to prevent
Lens removing by unauthorized person.
Mounting Holes of Support Kit
These two screws holes can be used to fix
support kits of ultra-short throw lens.
Note: The screws are for Lens support kits only;
overloading may damage the projector or cause
injury.
Recess for projector handling.
These four recesses can be used for handling
the projector.
Ceiling Mounting Hole
Total, 6 holes for M4 screw, maximum depth
14mm.
Security Slot
The slot can be used for Short-term protection
Note:
 When installing, ensure that you use only UL Listed ceiling mounts, Contact your dealer for information on
mounting the projector on a ceiling.
 With ceiling installation, use approved mounting hardware & M4 screws; maximum depth of screw: 18 mm.
8
DU8090Z DLP Projector - User Manual
IO Panel
TRIGGER(12V +/-1.5V)
When connected to the screen thtough a 3.5mm cable,
the screen deploys automatically on start up of the
projector. The screen reacts when the projector is
powered off.
RS-232
The 9-pin D-sub interface is used to connect to the PC
control system and projector maintenance.
Component (V, H, B/Pb, G/Y, R/Pr)
Connect RGBHV or Component signal from computer or
component video enabled device
VGA
Provide the standard 15-pin VGA connection and can
connect to RGB, HD Component or personal computer.
MONITOR OUT
Connect to a monitor to display the projected content.
HDBaseT/LAN
Connect an Ethernet cable (Cat5/Cat6, not supplied) from
a computer, network device, or HDBaseT transmitter.
HDMI I
Connect the HDMI cable from a computer or video device
DVI-D
Connect to DVI-D cable from a DVI-D output of the
device.
SDI IN/OUT
Connect to SDI source.
HDMI II
Connect the HDMI cable from a computer or video device
3D SYNC IN / Out
Connect to the 3D IR synchronization signal transmitter.
WIRED REMOTE
Connect the supplied remote controller to the projector
Note for Trigger
 When the projector is turned on, a control signal (DC 12V) outputs from this terminal, Screen controllers are
supplied and supported by screen manufacturers.
 Do not use this jack for anything other than intended use.
Note for Wired Remote
 Please make sure whether the port for insertion is correct before the terminal of the wired remote control is
inserted. The remote control may be damaged if inserted to the wrong port such as trigger. Do not use this jack for
anything other than intended use.
9
DU8090Z DLP Projector - User Manual
Control Panel
INPUT
Push the button to select the input signal. HDMI, DVI,
VGA, Component…etc.
CENTER LENS
Push the button to center the lens and calibrate the
parameter of lens shift, focusing and zooming.
Note: The lens memory function requires the accurate
lens adjustment parameter. Please center the lens every
time after the lens is mounted.
AUTO SYNC
Implement automatic signal synchronization.
Blank
Use the button to stop the projection temporarily
ASPECT
Change the aspect ratio of the current image and push
the button to change to the next aspect ratio settings.
LENS SHIFT
Use these four buttons to move the projected image to
desired position.
MENU
Push the button to display or hide the OSD menu.
FOCUS
Use the button to adjust the focus of projected image.
UP/Down/Left/Right
Use the button to select the OSD option.
ZOOM
Use the button to zoom in/out the projected image.
POWER
User the button to turn on/off the projector.
ENTER
Use the button to select settings or confirm the changed
settings.
EXIT
Push the button to return to the menu on the previous
level or exit the OSD menu.
10
DU8090Z DLP Projector - User Manual
Remote Control
On
Use the button to turn on the projector.
OFF
Use the button to turn off the projector.
FOCUS
Adjust the focus of the projected image.
ZOOM
Zoom in/out the projected image.
TEST PATTERN
Use the button to show the test pattern. Press this button again to switch to
the next pattern. Press the EXIT button to return to the projected image.
LENS SHIFT
Use the button to move the lens right or left.
ENTER
Use the button to select settings or confirm the changed settings.
MENU
Press the button to display or hide the OSD Menu.
EXIT
Press the button to return to the previous Menu or exit the OSD Menu.
AUTO PC
You can use this function to execute signal source auto synchronization
BLANK
Press the button to temporarily interrupt the projection.
STATUS
Show OSD MENU – SERVICE.
VGA
Select VGA input source.
COMPONENT
Select Component input source.
ASPECT
Press the button to display aspect ratio options.
HDMI1
Select HDMI1 input source.
HDMI2
Select HDMI2 input source.
DVI
Select DVI input source.
3G-SDI
Select 3G-SDI input source.
DisplayPort
Not available for this model.
HDBaseT
Select HDBaseT input source.
CLEAR (Not Applicable)
FREEZE
Freeze / cancel the freeze of the projected image.
ID SET (Not Applicable)
Wired Remote Jack
Connect to WIRED REMOTE terminal on the projector
11
DU8090Z DLP Projector - User Manual
Remote Control Operating Range
The remote control uses infrared transmission to control the projector. It is not necessary to point the remote directly
at the projector. Provided you are not holding the remote perpendicular to the sides or the rear of the projector, the
remote will function well within a radius of about 10 meters (25 feet) and 15 degrees above or below the projector
level. If the projector does not respond to the remote control, move a little closer.
Inserting the Remote Control Batteries
1
2
3
1. Remove the battery compartment cover by sliding the cover in the direction of the arrow.
2. Place two AA batteries with the correct polarity.
3. Slide on the cover as the arrow in the illustration.
Important:
- Avoid using the projector with bright fluorescent lighting turned on. Certain high-frequency fluorescent lights can
disrupt remote control operation.
- Be sure nothing obstructs the path between the remote control and the projector.
- Do not expose the remote control to high temperature or humidity; otherwise, the remote control will not work
Battery installation instructions
• Make sure the battery is installed with the correct polarity
• Do not use the old and new batteries or the batteries of different types together
• Remove the battery if the remote control may not be used for a long time to prevent the damage caused by leaks.
12
DU8090Z DLP Projector - User Manual
Installing or Removing the Optional Lens
Caution:
 Do not shake or place excessive pressure on the projector or the lens components as the projector and lens
components contain precision parts.
 When shipping the projector with the optional lens, remove the optional lens before shipping the projector. The lens
and the lens shift mechanism may encounter damage caused by improper handling during transportation.
 Before removing or installing the lens, be sure to turn off the projector and wait till the cooling fans stop, and turn off the
main power switch.
 Do not touch the lens surface when removing or installing the lens.
 Keep fingerprints, dust or oil off the lens surface. Do not scratch the lens surface.
 Work on a level surface with a soft cloth under it to avoid scratching.
 If you remove and store the lens, attach the lens cap to the projector to keep off dust and dirt.
Install New Lens
1. If the Lens cover is installed, pull the edge of the lens cover with one hand ( ① ), so that the lens cover can be
removed easily with the other hand ( ② )
2.
Align the " " symbol on the lens label with the "* " symbol on the top of the body (align to the center of the lens
hole) and pull in the lens.
3.
Make sure the lens is pushed into the holder and turn it clockwise to the "Lock" position. When turning the lens,
the "Click" sounds twice to indicate that the lens is completely fixed.
4.
Check if the lens is fixed successfully by pulling the lens out of the holder gently.
13
DU8090Z DLP Projector - User Manual
Removing the Existing Lens
1.
Push the LENS RELEASE button all the way in and rotate the lens counterclockwise. The existing lens will be
disengaged
2.
Pull out the existing lens slowly.
Caution:
When installing the lens into the projector, be sure to remove the lens cap from the back of the optional lens before
installing the optional lens into the projector. Failure to do so will cause damage to the projector.
There is one safety switch inside the lens slot on the projector to prevent unexpected injury by laser beam, the projector
cannot be turned on if the projection lens has not been installed or is not installed correctly. Please make sure the lens is
installed properly before tuning on the projector.
14
DU8090Z DLP Projector - User Manual
Lens Shift Range
The DU8090Z projector has the lens shift feature; the image can be shifted vertically or horizontally without moving
the projector. The lens shift range is shown in the percentage of the screen height, the maximum vertical shift range
of the image can be up 50% and down 30%, maximum horizontal range is 10% to the right, 10% to the left. Please
refer to below illustration.
Vertical lens shift
The projector is installed on the desk, the image can be moved up by 50% (0.5V) and down by 30% (0.3V).
The projector is mounted on ceiling, the projected image can be moved down by 50% (0.5V) and up by 30% (0.3V).
Caution:
 Ceiling installation must be done by a qualified professional. Contact your dealer for more information. It is not
recommended you install the projector yourself.
 Only use the projector on a solid, level surface. Serious injury and damage can occur if the projector is dropped.
15
DU8090Z DLP Projector - User Manual
Horizontal lens shift
The image can be shifted horizontally to the right or left by 10% (0.1H) without moving the projector.
Note:
 Above adjustable lens shift range is preset in DU8090Z for more flexible in installation, the best performance range
of the lens may vary with projection lens. Please refer to the projection lens specification.
 Lens shift range is reduced if Lens Type is set to UST Lens. Make sure Lens Type is set to Non-UST Lens if
Non-UST lens is used.
16
DU8090Z DLP Projector - User Manual
Making Connections
Follow the instructions below to connect DU8090Z projector to the video source, external control equipment (if any).
When connecting to the equipment, use the correct signal cable to connect to the signal source and ensure that the
cable is securely connected. Fasten the nut on the joint and connect the signal source equipment to the projector
according to the figure below.
Connecting to Personal Computer
You can connect the PC signal to be projected to the projector through the DVI-D, HDMI, VGA or RGBHV (BNC) cable.
If the signal to be input is VGA signal, connect the VGA cable to the external display to simultaneously monitor the
projected content.
Connecting to the Video Device
Connect the video equipment to the input port of the projector via the DVI-D, HDMI, Component Video, Composite
Video or S-Video Connector.
17
DU8090Z DLP Projector - User Manual
Connecting to the Control Equipment
The projector has the following control port for connecting to the control equipment:
HDBaseT/LAN (Network control): The projector supports network control. LAN and Digital share the port. If only
network control is used, you can connect the LAN on the projector to PC or through the local network. Refer to the
remote control guidelines for
RS-232 (RS-232 control): The projector can be remote-controlled by connecting the projector to PC or control system
Through the standard 9-pin serial cable (Straight Through Serial Cable). Refer to the Remote Communication Manual
for detailed information.
Wired remote control: If the projector cannot receive the IR signal from the remote control due to the overly long
distance or obstacles, you can connect the cable to the IR remote control or the external IR transmitter (optional) via
the WIRE input port to expand the working range of the remote control.
3D Sync Out/In: Connect to 3D IR sync signal transmitter or device.
Caution:
 When the terminal of the remote control cable is inserted to the wired control terminal of the projector, the
projector will automatically switch to the wired control mode and cannot be controlled through the IR signal of
the remote control. Disconnect the wired control terminal on the projector if you want to control through the IR
signal of the remote control.
 If the wired remote control cable or the external IR transmitter is inserted to the incorrect port, such as Trigger,
the remote control or the IR transmitter may be damaged. Make sure whether the port is correct
18
DU8090Z DLP Projector - User Manual
Connecting to the Screen Trigger
If your projection system includes the Electric projection screen and other 12V trigger device, you can connect these
devices to the 12V trigger to output and configure the output 12V signal settings, such as automation and the aspect
ratio of 16:10 through OSD control to Trigger. The projector will output 12V signals according to the current settings of
the aspect ratio and trigger when turned on. You can use the signal to control the screen or device.
19
DU8090Z DLP Projector - User Manual
Connecting to external HDBaseT Transmitter
The projector has a built-in HDBaseT receiver. With HDbaseT Transmitter (optional), the video, RS-232 and LAN
signals can be sent to the projector via a single RJ-45 cable. If the HDbaseT Transmitter you purchased supports the
input and output of the IR remote control, the control signals from the IR remote control can be sent to the DU8090Z
projector via the RJ-45 cable.
Note:
 The projector supports the video signal, R-232, IR remote control and the reception of the network control
signals but do not support Power over Ethernet (PoE).
 Set the Control -> RS232 -> Channel on the OSD menu to HDBaseT if you want to use the external HDBaseT
transmitter to send the RS232 command to the projector via the RJ45 cable and baud rate will switch to 9600.
 If the command is sent via the HDBaseT transmitter, the longest transmission distance is 100 meters. The
projection may be interrupted or interfered, or the control signal cannot be sent if the transmission distance is
exceeded.
 Use the RJ-45 Cat5e or above cable and avoid entwining. Entwining may cause damage or interfere signal
transmission, reduce the transmission distance and degrade the image quality.
20
DU8090Z DLP Projector - User Manual
Using the projector
Note:
 The projector is equipped with safety switch inside the lens mount hole; the projection lens must be installed in
the projector before turning on the power. Or the projection can’t be started.
 Use supplied power cable only.
Select the Input Voltage of AC Power
There is one slide switch near AC switch, pleases switch it to according input voltage of AC power.
Connecting to AC Power Supply
The AC power cord is included in the box, plug the power cord to the AC socket on the IO panel.
Turning on the Projector
Once the projector is correctly located and the power cable and other connections are in place, it is important that the
projector is powered on correctly in order to avoid damage to components and un-necessary wear and tear. Refer to
the following guide to power on the projector.
1. Press the main power switch to the on ( I ) position as
shown. POWER LEDs flashes then lights red.
21
DU8090Z DLP Projector - User Manual
2. Press the POWER button on the control panel or ON
button on the remote control.
3. The Power LED and LIGHT LED flashes green till
power on process is finished.
4. After few seconds, both LEDs keep green, the projector
is ready for use.
Turning off the Projector
Once the projector is no longer required, it is important to shut it down correctly to avoid damage or unnecessary
wear and tear to the projector.
Note:
 Do not unplug the power cable from the wall outlet or projector when the projector is powered on. Doing so
can cause damage to the AC IN connector of the projector and (or) the prong plug of the power cable. To turn
off the AC power supply when the projector is powered on, use a power strip equipped with a switch and a
breaker.
 Do not turn off the AC power supply within 10 seconds after making adjustment or changing the setting. Doing
so is possible to cause loss of adjustments and settings and return to default.
Refer to the following guide to shut down the projector.
1. Press the POWER button on the control panel or OFF
button on the remote control once, the Power Off window
displays.
2. Press the POWER button again on the OSD control panel
or remote control to verify power off, the power LED
flashes orange after Power Off is confirmed.
3. The projector enters Standby mode when the power LED
lights red.
4. Press the Main Power switch to the off position (O) to turn
off the projector.
22
DU8090Z DLP Projector - User Manual
Using On-Screen Display
Using the OSD Menu
The projector has an On-Screen Display (OSD) that lets you make image adjustments, change various settings and
check current projector status.
Navigating the OSD
You can use the remote control or the control buttons on the projector to navigate and make changes to the OSD.
The following illustration shows the corresponding buttons on the remote control and on the projector
1. To open the OSD, press the Menu button on the OSD control
panel or remote control. There are six folders on the menu.
Press the cursor ◄ or ► buttons to move through secondary
menus.
2. Press ▲or▼ to select menu items and ◄or► to change
values for settings. Press
to confirm the new setting.
3. Press RETURN to leave a submenu or MENU to close
menu
23
DU8090Z DLP Projector - User Manual
Menu Tree
Use the following table to quickly find a setting or determine the range for a setting.
Main Menu
INPUT
Submenu
Input Selection
PIP
Auto Source
Color Space
Aspect Ratio
Overscan
VGA Setup
Test Pattern
3D
PICTURE
Auto Sync
Picture Mode
Brightness
Contrast
Saturation
Hue
Sharpness
Color Temperature
HDMI1
HDMI2
VGA
Component
BNC
DVI
3G-SDI
HDBaseT
PIP Option
PIP Input
Position
Off
On
Auto
YPbPr
YCbCr
RGB-PC
RGB-Video
5:4
4:3
16:10
16:9
1.88
2.35
LetterBox
Source
Native
Off
Crop
Zoom
H Total
H Start
V Phase
V Start
White
Black
Red
Green
Blue
Checker Board
Crosshatch
H Burst
V Burst
Color Bar
3D Format
Eye Swap
DLP Link
Dark Time
Sync Delay
Sync Reference
Execute
High Bright
Presentation
Video
5400K
24
DU8090Z DLP Projector - User Manual
6500K
7500K
9300K
Native
Gamma
Input Balance
HSG
Noise Reduction
Dynamic Black
ALIGNMENT
Lens Lock
Lens Control
Lens Type
Lens Memory
Center Lens
Digital Zoom
Warp
Blanking
Edge Blend
Screen Format
CONTROL
Language
Projection Mode
Cooling Condition
High Altitude
Auto Power Off
1.0 / 1.8 / 2.0 / 2.2
/ 2.35 / 2.5 / S-Curve
Red Offset
Green Offset
Blue Offset
Red Gain
Green Gain
Blue Gain
Red
Green
Blue
Cyan
Magenta
Yellow
White
Reset
Off
On
Off
On
Zoom
Focus
Lens Shift
Non-UST Lens
UST Lens
Load Memory
Save Memory
Clear Memory
Execute
Digital Zoom
Dgital Pan
Digial Scan
Keystone
Rotation
Pincushion/Barrel
Top Left Corner
Top Right Corner
Bottom Left Corner
Bottom Right
Top
Bottom
Left
Right
Reset
Edge Blend
Align Pattern
White Level
Black Level
Reset
16:10
16:9
4:3
Front Desktop / Front Ceiling /
Rear Desktop / Rear Ceiling
Desktop / Ceiling / Freetilt /
Portrait / Auto
Off
Auto
Off
On
25
DU8090Z DLP Projector - User Manual
Auto Power On
Network
Light Power
Custom Power Level
Background
Startup Logo
Remote Sensor
Trigger
OSD Seting
SERVICE
Off
On
Standby Power
DHCP
IP Address
Subnet Mask
Gateway
DNS
Mac Address
Eco
Normal
Custom
Logo
Black
Blue
Off
On
Off
On
Off
Screen
5:4
4:3
16:10
16:9
1.88
2.35
LetterBox
Source
Native
Menu Position
Menu Transparency
Time Out
Model
Serial Number
Software Version 1
Software Version 2
Active Source
Signal Format
H/V Refresh Rate
Pixel Clock
Light Time
Thermal Status
Factory Reset
26
DU8090Z DLP Projector - User Manual
OSD Operation – INPUT
Input Selection
Use the shortcut key on the remote control or this function to select the input source, the Input options are as below.
The available input source of the product is HDMI 1, HDMI 2, VGA, Component (BNC), HDBaseT, DVI and 3G-SDI.
Sub Picture
PIP
This function allows you to split the screen for displaying the images from two input sources
PIP Option
Enable PIP by choosing “ON”, and two windows will be shown on the projected picture. The larger one is the
primary picture, the smaller one is the sub picture. By choosing “Off”, PIP function will be disabled, and only one
picture window projected.
PIP Input
Press ENTER to display available sources for the sub picture, and then select a source.
Note: The unavailable input sources of sub-menu will be gray out and cannot be selected. The available input
source of sub picture is as below combination list.
Main Picture
VGA
Component HDMI 1
HDMI 2
HDBaseT
3G-SDI
DVI
VGA
○
○
○
○
Component
○
○
○
HDMI 1
○
○
○
○
HDMI 2
○
○
○
HDBaseT
○
○
○
○
3G-SDI
○
○
○
DVI
○
○
○
○
27
DU8090Z DLP Projector - User Manual
Position
Find preferred location of PIP window.
Top Left: Display sub picture at top left of the screen.
Bottom Left: Display sub picture at bottom left of the screen.
Top Right: Display sub picture at top right of the screen.
Bottom Right: Display sub picture at bottom right of the screen.
PBP: Display sub picture next to main picture, the main screen is shrined to the same size as sub picture.
Auto Source
The Auto Source functions “ON” lets projector automatically search for the input signal.
Color Space
This function allows you to change the corresponding color space for the input signal in most cases, the default is Auto.
Auto: The projector detects the input signal and switches to the corresponding color space automatically.
YPbPr: Set the color space to ITU-R BT 601.
YCbCr: Set the color space to ITU-R BT 709.
RGB-PC: Use the RGB color space and set the black to 0, 0, 0 RGB, while set the white to 255, 255, 255 RGB (if
an 8-bit image is used).
RGB-Video: Use the RGB color space and set the black to 16, 16, 16 RGB while set the white to 235, 235, 235 (if
an 8-bit image is used) to correspond to the luminance value defined in the digital component standard.
Aspect Ratio
This function allows the user to adjust the aspect ratio of the projection image by ◄ ► keys.
Overscan Noise may appear on the edge of the projected image or image may be small than projected image, select below
option to hide the noise or extend the image.
Off: Display the original image.
Crop: Hide the edge of the image
Zoom: Extend the image to fit the projected area as possible.
VGA Setup Set the H Total, H Start, H Phase and V Start for the VGA signal by ENTER key.
Test Pattern The built-in images are provided for installation and adjustment. You can select Test Pattern on OSD or the TEST
PATTERN button on the remote control to show the test pattern. Press the ◄ or ► to select pattern or press EXIT key
again to exit the test pattern. The available test pattern options are White, Green, Crosshatch, Color Bar, Black, Blue,
H-Burst, Red, Chess Board and V Burst.
28
DU8090Z DLP Projector - User Manual
3D This function is to set the 3D format and sync method. The projector detects the type of input signals and provides
relevant options for setting. Before performing 3D setting, make sure that the input signal is connected.
3D Format Off: Turn off the 3D Display Mode. When Auto, Side by Side, Top and Bottom, or Frame Sequential is selected,
the 3D Mode will be turned on. To turn off the 3D Mode, select “Off” and press “ENTER”.
Auto: Allow the 3D format to automatically detect the formats of Frame Packing, Top and Bottom, and Side by
Side. The input signal is HDMI 1.4a 3D.
Side by Side (Half): This option is only applicable to input signal HDMI 1.4a 3D or HDMI signal sent by
HDBaseT Transmitter.
Top and Bottom: This option is only applicable to input signal HDMI 1.4a 3D or HDMI signal sent by HDBaseT
Transmitter.
Frame Sequential: Set input format under Frame Sequential.
Eye Swap: If the 3D image transmitted to the 3D glasses is reverse, you can set the Eye Swap to “Reverse” to
normalize the image. Otherwise, keeping mode of “Normal” would be suggested.
DLP Link: This function is to activate or deactivate the DLP Link sync.
Dark Time: Manually switch the Dark time for glasses tolerance, the available options are 0.65ms, 1.3ms and
1.95ms.
Sync Reference: The projector provides DLP Link and 3D IR sync for 3D display, you can specify the built-in
DLP Link or external 3D IR transmitter to synchronize the signal of the 3D glasses, or select Auto to set the sync
signal depended on the 3D format and if external 3D sync device is connected. This function is only applied to
the condition that 3D Format is Frame Sequential or external 3D sync device is connected to the projector.
External: Signal is sent from external 3D sync signal receiver.
Internal: Signal is sent by the projector, 3D sync signal is DLP Link.
Auto: Projector select 3D sync signal depended on the 3D format and if the extend 3D sync device is connected.
Auto Sync
You can use this function to execute signal source auto synchronization.
Important reminders:
 People with the following conditions should view 3D image with great care:
 Children under six years in age
 People who are allergic to light, unhealthy and have the history of cardiovascular diseases
 People who are tired or lack of sleep
 People who are under the impact of drug or alcohol
 Normally, it is safe to watch 3D images. However, some people might feel uncomfortable.
 Refer to the guidelines revised and released by the 3D League on December 10, 2008 who match 3D images need
to take a break for at least 5 to 15 minutes every thirty minutes or one hour.
29
DU8090Z DLP Projector - User Manual
OSD MENU – PICTURE
Picture Mode Use ◄or► to select desired picture mode High Bright: The highest brightness output mode is suitable for the application where the highest brightness output
is needed.
Presentation: The best projection effect is suitable for the presentation or picture.
Video: The mode is suitable for playing video content.
Brightness
Press ENTER, and use ◄ or ► to increase or decrease the level of brightness.
Contrast
Press ENTER, and use ◄ or ► to adjust the contrast of the projected image.
Saturation
Press ENTER, and use ◄ or ► to adjust the level of saturation.
Hue
Press ENTER, and use ◄ or ► to adjust the level of hue.
Sharpness
Press ENTER, and use ◄ or ► to adjust the sharpness, which changes the high-frequency details.
Color Temperature
The default of color temperature is Native, and it is suitable for most situations. As color temperature rises, the picture
will appear bluer, while as the color temperature decreases, the picture will appear redder. The available options are
Native, 5400K, 6500K, 7500K and 9300K
Gamma
When the ambient light is so bright that may affect the projection of the details in the dim area of the image, you can
change the gamma to adjust the chrominance. The available options are 1.0, 1.8, 2.0, 2.2, 2.35, 2.5 and S-Curve.
Input Balance
When ambient light is too bright or changes, the projected image details may be affected, you can adjust the option to
make the projected colors of image closer to desired colors. There are two options for fine tuning Red, Green and Blue.
30
DU8090Z DLP Projector - User Manual
Offset: These three options will shift the color spectrum for the whole image and change its brightness, if minimal amount
of red, green or blue appears in the gray areas, you can adjust the offset of the corresponding color accordingly. By
increasing the offset, the image brightness will become lower.
Gain: These three options are used to increase or decrease the range of color input for the entire image. If minimal
amount of red, green or blue appears in the gray areas, lower the gain of the corresponding color accordingly. As gain
increases, the contrast of the image will become lower. HSG
HSG is a function to adjust Hue, Saturation and Gain independently, it allows for specified color adjustments that are more
intuitive. You can adjust Hue, Saturation and Gain for Red, Green, Blue, Cyan, Magenta, Yellow and white independently.
Noise Reduction
Use ◄► to adjust the noise of the projected image. This function is used to remove the noise of the image with interlaced
scanning input. Generally, noise reduction can lower the high-frequency details and make the image softer.
Dynamic Black
This is function can be used to enhance the black level of the projected image.
OSG MENU – ALIGNMENT
Lens Lock
This function can be used to disable lens control for preventing unauthorized operation or disoperation in lens control
related functions including Lens Shift, Zoom/Focus Adjustment and Center Lens. Recommend to turn on Lens Lock
function to disable the Lens control after lens adjustment is done.
Lens Control
Select this function to open Lens Control menu for adjustment of Zoom, Focus, or Shift. You can use the ENTER button to
switch the Zoom / Focus or Shift menu. Use ▲or▼ to adjust zoom and vertical shift of the lens, or use ◄ ► to adjust
focus and horizontal shift of the lens.
31
DU8090Z DLP Projector - User Manual
Lens Type
There are eight projections lens can be used in DU8090Z, the initial projection position of Ultra Short Throw (UST) Lens is
different to other seven projection lenses. The projector preset two initial projection positions for these two types
accordingly, Center Lens function can moves the lens to the initial position (center) automatically per the setting. Please
set this option to UST Lens if Ultra Short Throw Lens is installed in the projector, otherwise please set it to Note:
 The lens will moved to the position which is lower than the initial projection of Ultra Short Throw Lens after
performing Center Lens function, and cause the projected image is blocked by the top cover of the projector if
it’s set to Non-UST Lens. In this case, please perform the Lens shift function to move up the Lens till the
image can be projected normally.
 If Ultra Short Throw Lens is installed and UST Lens is selected, you can perform Center Lens to move Lens to
initial projection position automatically.
 When using non-UST lens and lens shift range is limited, please make sure Lens type setting is set to
Non-UST Lens.
Lens Memory
This projector supports Lens Memory function, Lens shift, Zoom and Focus memory can be stored in the projector up to
10 sets. You can load the stored memory setting to set up the lens automatically.
Load Memory: Use ▲▼ to select the desired memory setting then press ENTER button to execute the lens setting,
the projector will adjust the Lens position, Zoom and Focus automatically.
Save Memory: Use ▲▼ to select the memory set for storing the setting then press ENTER button to confirm.
Clear Memory: Select the memory set to be cleared then press ENTER button to confirm clearing memory set.
Center Lens This is the lens calibration function, the projector calibrates the lens shift, focus and zoom parameters for the precise lens
memory function. After performing this function, the lens will be moved to the center position as factory default setting.
Note:
 There are two default center positions for UST (Ultra Short Throw) Lens and non-UST Lens, make sure Lens
Type setting is correct before performing this function.
 If Ultra Short Throw Lens is installed, make sure the support kit is detached before performing Center Lens.
Digital Zoom
Press ENTER button to select the options to enlarge the image or shift the image.
Digital Zoom: Use ◄► to enlarge the projected image.
Digital Pan: Use ◄► to move the projected image horizontally. This function is only available when projected image
is enlarged.
Digital Scan: Use ◄► to move the projected image vertically. This function is only available when projected image is
enlarged.
Reset: The setting will be reset to default value.
Warp
This function is used to correct the distortion of image.
Keystone: Press ◄► to correct horizontal distortion or ▲▼ to correct vertical distortion.
Rotation: Press ◄► to correct incorrect angle of image.
Pincushion / Barrel: Press ◄► to correct pincushion/barrel distortion.
Top Left Corner: Press ◄► to correct the distortion at top-left of the picture.
Top Right Corner: Press ◄► to correct the distortion at top-right of the picture.
Bottom Left Corner: Press ◄► to correct the distortion at bottom-left of the picture.
Bottom Right Corner: Press ◄► to correct the distortion at bottom-right of the picture.
32
DU8090Z DLP Projector - User Manual
Blanking: This function can adjust the edges of the image and hide surplus sections of the projection.
Top: Press▲▼ to adjust the top blanking area on the projected picture.
Bottom:Press▲▼ to adjust the bottom blanking area on the projected picture.
Left: Press ◄► to adjust the left blanking area on the projected picture.
Right: Press ◄► to adjust the right blanking area on the projected picture.
Reset
All the settings toward blanking will set to default.
Edge Blend
Edge Blend function requires multiple projectors to simultaneously project on the same screen. Use this function to adjust
the uniformity of image. To use this function, Edge Blending must be enabled on both projectors. The functions as follows
can be only adjusted when Edge Blend is turned on.
Edge Blend: If the user would like to function Edge Blend, turn this function to On.
Align Pattern: If user turns this function to On, the projector will show pattern for user to adjust the overlapping part of
projection.
White Level: White Level is used to set the overlapped area for blending in multi-projection application, the
overlapping When projecting White, the area where the two images overlap is projected twice the projectors' white
output levels. The solution is to adjust the White Level. First make sure that the units connected to the projectors are
outputting black. Then increase the White Level (Top, Bottom, Left, and Right) until the non-overlap area's brightness
matches the overlap area.
Black Level: The purpose of Black Level is to increase the black level of non-overlapping area. When projecting black,
the area where the two images overlap projects twice the projectors' black output levels. The solution is to adjust the
Black Level. First make sure that the units connected to the projectors are outputting black. Then increase the Black
Level (Top, Bottom, Left, and Right) until the non-overlap area's brightness matches the overlap area.
Reset: All the settings toward edge blend will set to default.
Screen Format: Sleet the screen format to 16:10, 16:9 and 4:3.
33
DU8090Z DLP Projector - User Manual
OSD MENU – CONTROL
Language
Select desisted OSD language, the available languages options are English, Española, Deutsch, Portuguese, 简体中文,
繁體中文, 日本語, 한국어.
Projection Mode
Use The projection mode option can be used to change the direction of the projected image.
Front: Install the projector on the table and project the image on the screen forward.
Ceiling + Front: Mount the projector on the ceiling and project the image on the screen forward, the image is
overturned.
Rear: Install the projector on the table and project the image from the rear of the screen.
Ceiling + Rear: Mount the projector on the ceiling and project the image from the rear of the screen, the image is
overturned.
Auto: Built-in sensor detects the projector orientation and switch corresponding projection mode, note this function is
applicable for front projection only, the image orientation when projecting from rear has to be adjusted manually.
Cooling Condition
The projector is equipped with orientation sensor for switching cooling condition automatically; you can set it to Auto or
adjust the cooling condition by manual.
Front: The projector is installed on the table.
Ceiling + Front: The Projector is mounted on the ceiling.
Freetilt: The projector is installed with tile angle; the angle is over 30 degree.
Auto: Built-in sensor detects the installation orientation and switches to corresponding cooling condition.
Note:
 Incorrect Projection Mode setting may affect hot air exhausting from the projector, the heat and high
temperature may cause the projector to enter system protection or damage component.
High Altitude
Use this function to adjust the cooling fan of the projector to get well cooling if the projector is installed in an area over
5000 feet. The projector is equipped with altitude sensor which is capable of detecting atmosphere pressure for estimating
altitude; it can adjust automatically to corresponding setting based on estimated altitude if this option is set to Auto. If you
34
DU8090Z DLP Projector - User Manual
prefer to set it by manual, you can select On or Off.
Off: Turn off High Altitude mode if the projector is installed in an area under 5000 feet.
On: Turn on High Altitude mode if the projector is installed in an area over 5000 feet.
Auto: Set up this mode automatically by estimated altitude.
Note:


Estimate Altitude is calculated by atmosphere pressure, it may have the tolerance comparing to actual
altitude.
If any over temperature or system protection message, please adjust High Altitude by Manual.
In some application, regular cooling fan setting may not supply enough cold air for system cooling even
Auto Power Off
This function is set to OFF by default. When it is set to ON and no input signal is received within 20 minutes, the projector
will turn off automatically.
Auto Power On
This function is set to OFF by default. When it is set to ON, the projector will turn on automatically when y AC power is
turned on next time. You can use this function and the power switch (instead of the remote control) to turn on the projector.
Set this function to OFF if it’s unnecessary.
Network
Use this function to configurator the network settings so that you can control the projector via the network.
Press ▲▼ and Enter button to select Network and network settings. Please refer to Remote Communication Manual for
further information.
Standby Power
This option allows you to set up power consumption at standby status,
On: Projector maintains in the standby at higher power consumption (< 6W) for projector control via LAN. In this
mode, the projector can be turned on by RS-232 command or web control.
Off: Projector maintains in the standby at lowest power consumption (<0.5W), the projector can be turned on by
the power button on the remote control or control panel only.
DHCP: Set DHCP to ON/OFF. When DHCP is set to ON, the DHCP server of the domain will assign an IP address to
the projector. The IP address will appear on the IP address window without need to make any input. If the domain
cannot assign any IP address, 0.0.0.0 will be shown on the IP address window.
IP Address: To specify an IP address, press the Enter button to show the IP address input window. Use the ◄►
button to select the number in the address to change. Use the ▲▼ button to increase or decrease the number in the IP
address. Network IP Address 172. xxx. xxx. xxx.
Subnet Mask: Set the submask. The input method is the same as the setting for IP address.
Gateway: Set the gateway. The input method is the same as the setting for IP address.
DNS: Set the DNS. The input method is the same as the setting for IP address.
MAC Address: Show projector’s MAC Address.
Light Power
Use the ◄► function to select the Eco, Normal or Custom Power Level mode.
Eco: Projection operates in the energy-saving mode, which is equivalent to 80 % power of light source.
Normal: Projection operating with normal lamp power can obtain the brightest projection display.
Custom Power Level: User can decide the power level depending on his or her preference. Custom Power Level
Use the ◄► function to select the Custom Power Level. This function is available only when the Light Power is set to
Custom Power Level, which range is allowed to adjust from 20% to 100% of normal mode, and it cannot be selected
under the Normal or Eco mode.
35
DU8090Z DLP Projector - User Manual
Background
User can use this function to specify the image displayed on the blank screen when there is no input signal. The
selectable items are Logo, Black and Blue, the default setting is Logo. Startup Logo
Press ENTER button, and use the ◄► function to turn on / off the Startup Logo.
Remote Sensor
The default is On. However, there are three conditions that will be suggested to turn off “Remote Sensor”; the possible
condition is that if the user uses wired control, he or she can set this function to Off, or that if the projector IR location is
exposed to the bright sunlight or fluorescence, or that projector control is not controlled by remote. If the user would like to
reset to On, user can only set by OSD panel or RS-232.
Trigger
The projector is provided with a set of trigger output. User can connect the trigger to the screen with projector by the cable.
If user does so, once the projector is powered, the screen would be automatically turned on as well. There is a 2-3 second
delay to activate this function. The selectable aspect ratios are as follows:
Off: Turn off screen trigger.
5:4: Outputs 12V of power on Trigger when Aspect Ratio is set to 5:4.
4:3: Outputs 12V of power on Trigger when Aspect Ratio is set to 4:3.
16:10: Outputs 12V of power on Trigger when Aspect Ratio is set to 16:10.
16:9: Outputs 12V of power on Trigger when Aspect Ratio is set to 16:9.
1.88: Outputs 12V of power on Trigger when Aspect Ratio is set to 1.88.
2.35: Outputs 12V of power on Trigger when Aspect Ratio is set to 2.35.
Letterbox: Outputs 12V of power on Trigger when Aspect Ratio is set to Letterbox.
Native: Outputs 12V of power on Trigger when Aspect Ratio is set to Native.
Unscaled: Outputs 12V of power on Trigger when Aspect Ratio is set to Unscaled.
Auto: Outputs 12V of power on Trigger automatically.
OSD Settings
Menu Position: Adjust menu position through this function, the available position options are at Top-Left:
Top-Right, Bottom-Left, Bottom-Right and center of the screen.
Menu Transparency: Change the transparency of OSD Menu, the background color of the OSD can be adjusted from
darker to lighter if you want to display complete projected image. Time Out: Set up the timer to exit OSD menu, the available options are Always On, 10 Seconds, 30 Seconds and 60
Seconds.
Message Box
This function allows you to disable the pop-up message at bottom-right of the screen. 36
DU8090Z DLP Projector - User Manual
OSD MENU – SERVICE
Model
Display the project model name.
Serial Number
Display the serial number of the projector.
Software Version 1 / Software Version 2
Display the software version in the projector.
Active Source
Display the current input source information.
Signal Format
Display current input source format
.
H/V Refresh Rate
Display horizontal and vertical refresh rate of the current picture.
Pixel Clock
Display pixel clock of the current input signal.
Light Time
Display accumulated usage of projection light source
Thermal Status
Display current of the thermal management components.
Factory Reset
The user can use this function to reset all the settings to factory default; light time.
37
DU8090Z DLP Projector - User Manual
Product Specification
Display Type
Brightness
Native Resolution
Maximum Resolution
Contrast Ratio
Illumination Type
Throw Ratio*
Image Size (Diagonal)*
Projection Distance*
Projection Lens*
Zoom Ratio*
Aspect Ratio
Offset
Keystone Correction
Horizontal Frequency
Vertical Scan Rate
Edge Blending
Warping
3D Functionality
Adjustable
Lens Shift Range
I/O Connection Ports
Projection Method
Security Solutions
Dimensions (WxDxH)
Weight
Available Colours
Noise Level
Power Supply
Power Consumption
Standard Accessories
Optional Accessories
Single Chip 0.67" DLP Technology
8,000 ANSI Lumens
WUXGA (1920 x 1200)
WUXGA (1920 x 1200)@60Hz (Reduced Blanking)
10,000:1
Laser Phosphor
1.73 - 2.27:1
40" - 500"
1.45 - 24.85m (4.77ft to 81.52ft)
F = 1.7 - 1.9, f = 26 - 34mm
1.3x
16:10
Motorized Lens Shift
Horizontal ±60°, Vertical ±40° ( individual adjustable range)
15, 30 – 90Hz
50 - 85Hz
Yes (Built-In)
Yes (Built-In)
Yes (DLP® Link™, HDMI v1.4 (Blu-ray, side by side, frame packing, top and
bottom))
Vertical: -30 - +50%, Horizontal: ±10%
HDMI v1.4a (x2) DVI-D, Component (5 BNC), VGA-In, 3G-SDI-In/Out,
RS-232, VGA-Out, 3D-Sync In/Out, 12v Trigger, Wired Remote,
HDBaseT™/LAN (Shared)
Table Top, Ceiling Mount (Front or Rear)
Kensington® Security Slot, Security Bar, Anti-Theft Lens Screw
500 x 580 x 205mm (19.7” x 22.8" x 8.1")
28kg (61.7lbs)
White (DU8090Z-WH), Black (DU8090Z-BK)
40dB (Normal Mode)
AC 100-240V, 50/60Hz
850W (Normal Mode), 675W (Eco. Mode), <6W (Network Standby), <0.5W
(Eco Standby Mode)
AC Power Cord, Remote Control w/Batteries, Lens Cap, Anti-Theft Lens
Screw, Documentation Kit
Interchangeable Lens Options
*Note: Standard Lens
**Note: Lens shift compatibility with all lenses except D88-WF18501 Wide Fixed Lens (3797745100-SVK) and D88-UST01 Ultra-Short
Throw Lens (3797855700-SVK)
©2016 Vivitek. Vivitek is a trademark of Delta Electronics, Inc. Other trademarks are the properties of their respective owners. Values,
weights and dimensions shown are approximate. Errors and omissions accepted. Specifications are subjection to change without prior
notice.
38
DU8090Z DLP Projector - User Manual
Supported Signal Input Timing
Signal Format
Resolution
Frame Rate
(HZ)
VGA, BNC
SOG
RGBHV
HDMI / HDBaseT
RGB
YUV
8-bit
PC
Apple Mac
SDTV
EDTV
HDTV
640x480
59.94
O
O
640x480
74.99
O
O
640x480
85
O
O
800x600
60.32
O
O
800x600
75
O
O
800x600
85.06
O
O
848x480
47.95
O
O
848x480
59.94
O
O
1024*768
60
O
O
1024*768
75
O
O
1024*768
85
O
O
1280x720
47.95
O
O
1280x1024
60.02
O
O
1280x1024
75.02
O
O
1280x1024
85.02
O
O
1600x1200
60
O
O
1920x1080
47.95
O
O
1680x1050
59.94
O
O
1920x1200 RB
50
O
O
1920x1200 RB
60
O
O
1400X1050
60
O
O
1366 x 768
60
O
O
1440 x 900
60
O
O
1280 x 768
60
O
O
1280 x 800
60
O
O
1280 x 960
60
O
O
640x480
66.59
O
O
832x624
74.54
O
O
480i
59.94
1440x480i
60
1440x576i
50
576i
50
HD/SDI/3G
10-bit
12-bit
O
O
O
O
O
O
O
O
O
O
O
O
480p
59.94
O
O
O
O
O
O
576p
50
O
O
O
O
O
O
1035i
60
O
O
O
O
O
O
O
1080i
50
O
O
O
O
O
O
O
1080i
59.94
O
O
O
O
O
O
O
1080i
60
O
O
O
O
O
O
O
39
DU8090Z DLP Projector - User Manual
PsF formats
720p
50
O
O
O
O
O
O
O
720p
59.94
O
O
O
O
O
O
O
720p
60
O
O
O
O
O
O
O
1080p
23.98
O
O
O
O
O
O
O
1080p
24
O
O
O
O
O
O
O
1080p
25
O
O
O
O
O
O
O
1080p
29.97
O
O
O
O
O
O
O
1080p
30
O
O
O
O
O
O
O
1080p
50
O
O
O
O
O
O
O
1080p
59.94
O
O
O
O
O
O
O
1080p
60
O
O
O
O
O
O
O
1080sf
30
O
1080sf
25
O
Supported 3D Signal
3D Format
Resolution
V-Freq (Hz)
V-Total
H-Freq (kHz)
HDMI I, HDMI II
720p50
Frame Packing
1280x720
50.00
1470
37.50
O
720p59
Frame Packing
1280x720
59.94
1470
44.96
O
720p60
Frame Packing
1280x720
60.00
1470
45.00
O
720p50
Top-and-Bottom
1280x720
50.00
750
37.50
O
720p59
Top-and-Bottom
1280x720
59.94
750
44.96
O
720p60
Top-and-Bottom
1280x720
60.00
750
45.00
O
1080p23
Frame Packing
1920x1080
23.98
2205
26.97
O
1080p24
Frame Packing
1920x1080
24.00
2205
27.00
O
1080i50
Side-by-Side (Half)
1920x1080
50.00
1125
56.25
O
1080i59
Side-by-Side (Half)
1920x1080
59.94
1125
67.43
O
1080i60
Side-by-Side (Half)
1920x1080
60.00
1125
67.50
O
1080p50
Side-by-Side (Half)
1920x1080
50.00
1125
56.25
O
1080p59
Side-by-Side (Half)
1920x1080
59.94
1125
67.43
O
1080p60
Side-by-Side (Half)
1920x1080
60.00
1125
67.50
O
1080p50
Top-and-Bottom
1920x1080
50.00
1125
56.25
O
1080p59
Top-and-Bottom
1920x1080
59.94
1125
67.43
O
1080p60
Top-and-Bottom
1920x1080
60.00
1125
67.50
O
1080p50
Frame Sequential
1920x1080
50.00
1125
56.25
O
1080p59
Frame Sequential
1920x1080
59.94
1125
67.43
O
1080p60
Frame Sequential
1920x1080
60.00
1125
67.50
O
*3D Glasses Refreshing Rate: 96/100/120Hz
*3D Sync signal: DLP Link, IR
40
DU8090Z DLP Projector - User Manual
Product Dimensions
41
DU8090Z DLP Projector - User Manual
LED Indication
Several indicators messages are used to display the current projector status or alert the abnormal message.
Power LED
LED Display
Projector status
Off
AC Power is turned off
Flashing
On
Procedure
Green
Projector is turning on.
wait till projector start displaying
Orange
Projector is under cooling
wait until cooling finish ( ~ 120 sec)
Red
Standby mode
Green
Projector is on
Status LED
LED Display
Projector status
Off
Normal status
Flashing
On
Red (Cycles of 1)
Cover is opened.
Red (Cycles of 4)
Cooling fan error
Red
System Error
Procedure
Check if the top cabinet is installed properly.
Contact with your nearest authorized dealer or service
center.
Contact with your nearest authorized dealer or service
center.
Light Source LED
LED Display
Off
Flashing
On
Projector status
Procedure
Light source is off
Green
Projector is turning on.
Red (Cycles of 6)
Light source lit fail
Red
Light source is end-of-life
Green
Light source is on
Contact with your nearest authorized dealer or service
center.
Contact with your nearest authorized dealer or service
center.
Temp LED
LED Display
Projector status
Off
Normal status
Flashing
Red
Procedure
Contact with your nearest authorized dealer or service
center.
Over temperature error
42
DU8090Z DLP Projector - User Manual
About the VIVITEK Support
If you cannot find solutions from this user guideline, please contact us using the contact information below:
North America
Vivitek Service Center
15700 Don Julian Road, Suite B
City of Industry, CA. 91745
U.S.A
Tel: 855-885-2378 (Toll-Free)
Email: T.services1@vivitekcorp.com
URL: www.vivitekusa.com
Europe and Africa
Vivitek Service & Support
Zandsteen 15
2132 MZ Hoofddorp
The Netherlands
Tel: +31 20 655 0960
Email: support@vivitek.eu
URL: www.vivitek.eu
China
Vivitek Service Center
201209, Room 1802, 18/F, Cimic Tower, No.1090, Century Avenue, Pudong, Shanghai
Tel: 400-888-3526 (Toll-Free)
Tel: 021-58360088-142 (Direct)
Email: service@vivitek.com.cn
URL: www.vivitek.com.cn
Asia and Taiwan
VIVITEK after-sales service
Vivitek Corporation, Co., Ltd.
4F., No.186, Ruiguang Rd., Neihu Dist., Taipei City 11491
TEL: 86-28-797-2088
FAX: 86-26-600-2358
E-mail: kenny.chang@vivitek.com.tw
URL: www.vivitek.com.tw
43
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising