EMQ-GS-4210-24P2S v1.0
24-Port 10/100/1000T 802.3at PoE +
2-Port 100/1000X SFP Managed Switch
GS-4210-24P2S
Quick Installation Guide
Table of Contents
1. Package Contents........................................................................................ 3
2.Requirements.............................................................................................. 4
3. Terminal Setup............................................................................................ 5
4. Logon to the Console................................................................................... 6
5. Configuring IP Address via the Console......................................................... 7
6. Saving the Configuration via the Console....................................................... 9
7. Starting Web Management..........................................................................10
8. Saving Configuration via the Web................................................................13
9. Recovering Back to Default Configuration......................................................14
10. Customer Support......................................................................................15
1.Package Contents
Thank you for purchasing PLANET 24-Port 10/100/1000T 802.3at PoE + 2-Port
100/1000X SFP Managed Switch, GS-4210-24P2S. “PoE Managed Switch”
mentioned in this quick installation guide refers to the GS-4210-24P2S.
Open the box of the PoE Managed Switch and carefully unpack it. The box should
contain the following items:
zz The GS-4210-24P2S x 1
zz Quick Installation Guide x 1
zz RS-232 to RJ-45 Cable x 1
zz Rubber Feet x 4
zz Two Rack-mounting Brackets with Attachment Screws x 1
zz Power Cord x 1
zz SFP Dust-proof Cap x 2
If any item is found missing or damaged, please contact your local reseller for
replacement.
3
2.Requirements
zz Workstations running Windows XP/2003/Vista/7/8/2008, MAC OS X or later,
Linux, UNIX, or other platforms are compatible with TCP/IP protocols.
zz Workstations are installed with Ethernet NIC (Network Interface Card)
zz Serial Port Connection (Terminal)
 The above Workstations come with COM Port (DB9) or USB-to-RS-232
converter.
 The above Workstations have been installed with terminal emulator, such as
Hyper Terminal included in Windows XP/2003.
 Serial cable -- one end is attached to the RS-232 serial port, while the other
end to the console port of the PoE Managed Switch.
zz Ethernet Port Connection
 Network cables -- Use standard network (UTP) cables with RJ-45 connectors.
 The above PC is installed with Web Browser and JAVA runtime environment
plug-in.
Note
4
It is recommended to use Internet Explore 8.0 or above to access
the PoE Managed Switch. If the Web interface of the PoE Managed
Switch is not accessible, please turn off the anti-virus software or
firewall and then try it again.
3.Terminal Setup
To configure the system, connect a serial cable to a COM port on a PC or notebook
computer and to RJ-45 type of console port of the PoE Managed Switch.
PC / Workstation
with
Terminal emulation software
RS-232 to RJ-45 Cable
Serial Port
PoE Managed Switch
Serial Port
115200,8,n,1
Figure 3-1: PoE Managed Switch Console Connectivity
A terminal program is required to make the software connection to the PoE
Managed Switch.
1.Run terminal program on the OS.
2.When the following screen appears, make sure that the COM port should be
configured as:
zz Baud
: 115200
zz Data bits
: 8
zz Parity
: None
zz Stop bits
: 1
zz Flow control
: None
Figure 3-2: COM Port Configuration
5
4.Logon to the Console
Once the terminal is connected to the device, power on the PoE Managed Switch
and the terminal will run self testing procedures. Then, the following message
asks to login user name and password. The factory default user name and
password are shown as follows and the login screen in Figure 4-1 appears.
Username: admin
Password: admin
Figure 4-1: PoE Managed Switch Console Login Screen
The user can now enter commands to manage the PoE Managed Switch. For a
detailed description of the commands, please refer to the following chapters.
Note
6
1.For security reason, please change and memorize the new password after this first setup.
2.Only accept command in lowercase letter under console interface.
5.Configuring IP Address via the Console
The PoE Managed Switch is shipped with default IP address as follows:
IP Address: 192.168.0.100
Subnet Mask: 255.255.255.0
To check the current IP address or modify a new IP address for the PoE Managed
Switch, please use the procedures as follows:
Display of the current IP address
1.On “GS-4210-24P2S#” prompt, enter “show ip”.
2.The screen displays the current IP address, Subnet Mask and Gateway shown in
Figure 5-1.
Figure 5-1: IP Information Screen
7
 Configuration of the IP address
3.On “GS-4210-24P2S#” prompt, enter “configure”.
4.On “GS-4210-24P2S (config)#” prompt, enter the following command and
press <Enter> as shown in Figure 5-2.
GS-4210-24P2S (config)# ip address 192.168.1.100 mask 255.255.255.0
GS-4210-24P2S (config)# ip default-gateway 192.168.1.254
The previous command would apply the following settings for the PoE Managed
Switch.
IP Address: 192.168.1.100
Subnet Mask: 255.255.255.0
Gateway: 192.168.1.254
Figure 5-2: Setting IP Address Screen
5.Repeat Step 1 to check if the IP address is changed.
If the IP is successfully configured, the PoE Managed Switch will apply the new IP
address setting immediately. You can access the Web interface of PoE Managed
Switch through the new IP address.
Note
8
If you are not familiar with console command or the related parameter, enter “?” anytime in console to get the help description.
6.Saving the Configuration via the Console
In switch, the running configuration file stores in the RAM. In the current version,
the running configuration sequence running-config can be saved from the RAM to
FLASH by save command or copy running-config startup-config command, so
that the running configuration sequence becomes the startup configuration file,
which is called configuration save.
1.On “GS-4210-24P2S#” prompt, enter “copy running-config startup-config”
as shown in Figure 6-1.
Figure 6-1: Saving the Configuration Screen
9
7.Starting Web Management
The following shows how to start up the Web Management of the PoE Managed
Switch. Note the PoE Managed Switch is configured through an Ethernet
connection. Please make sure the manager PC must be set on the same IP
subnet address.
For example, the default IP address of the PoE Managed Switch is 192.168.0.100;
then the manager PC should be set at 192.168.0.x (where x is a number
between 1 and 254, except 100) and the default subnet mask is 255.255.255.0.
PC / Workstation
with Web Browser
192.168.0.x
Managed Switch
RJ-45/UTP Cable
IP Address:
192.168.0.100
Figure 7-1: IP Management Diagram
 Logging in the PoE Managed Switch
1.Use Internet Explorer 8.0 or above Web browser and enter IP address
http://192.168.0.100 to access the Web interface.
10
2.When the following dialog box appears, please enter the default user name and
password “admin”. The login screen in Figure 7-2 appears.
Default Username: admin
Default Password: admin
Figure 7-2: Web Login Screen
3.After entering the password, the main screen appears as Figure 7-3 shows.
Figure 7-3: Web Main Screen of PoE Managed Switch
11
The Switch Menu on the left of the Web page lets you access all the commands
and statistics the PoE Managed Switch provides.
Figure 7-4: Switch Menu
Now, you can use the Web management interface to continue the Switch
management. Please refer to the user’s manual for more.
12
8.Saving Configuration via the Web
In the PoE Managed Switch, the running configuration file stores in the RAM. In
the current version, the running configuration sequence of running-config can be
saved from the RAM to FLASH by “Save Configurations to FLASH” function, so
that the running configuration sequence becomes the startup configuration file,
which is called configuration save.
To save all applied changes and set the current configuration as a startup
configuration. The startup-configuration file will be loaded automatically across a
system reboot.
1.Click “SAVE > Save Configurations to FLASH” to login “Configuration
Manager” Page.
2.Press the “Apply” button to save running configuration to startup configuration.
13
9.Recovering Back to Default Configuration
IP Address has been changed or admin password has been
forgotten –
To reset the IP address to the default IP Address “192.168.0.100” or reset the
login password to default value, press the reset button on the front panel for
about 10 seconds. After the device is rebooted, you can login the Web interface
management within the same subnet of 192.168.0.xx.
GS-4210-24P2S
1000
10/100
2
LNK
LNK
ACT
ACT
PoE In-Use
PWR
4
6
8
10
12
14
16
18
20
22
24
26
1000
100
PoE
1
3
5
7
9
11
13
15
17
19
21
23
25
PoE
Figure 9-1: GS-4210-24P2S Reset Button
14
LNK
LNK
ACT
ACT
RESET
10. Customer Support
Thank you for purchasing PLANET products. You can browse our online FAQ
resource and User’s Manual on PLANET Web site first to check if it could solve your
issue. If you need more support information, please contact PLANET switch support
team.
PLANET online FAQ:
http://www.planet.com.tw/en/support/faq.php?type=1
Switch support team mail address:
support_switch@planet.com.tw
GS-4210-24P2S User’s Manual:
http://www.planet.com.tw/en/support/download.php?type1=1&model=48553&type=3
Copyright © PLANET Technology Corp. 2014.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their
respective owners.
15
This page is intentionally left blank
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising