INSTALLATION INSTRUCTION WS-W1408, WS-W1414, WS-W1420 Ledge

INSTALLATION INSTRUCTION WS-W1408, WS-W1414, WS-W1420 Ledge
INSTALLATION INSTRUCTION
Ledge
WS-W1408, WS-W1414, WS-W1420
WARNING
IMPORTANT: NEVER attempt any work without shutting off the electricity.
-
Read all instructions before installing.
-
System is intended for installation by a qualified electrician in accordance with the National Electrical Code and local
regulations.
-
Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF” the circuit breaker switch(es) that control the power to the fixture or room that you are working on.
-
Place the wall switch in the “OFF” position.
CAUTION
-
All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this fixture.
CAUTION When handling the fixture, do not apply pressure to the LEDs. Hold the fixture by the base only.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
-
Lisez toutes les instructions avant d’installer.
-
Système est destiné à être installé par un électricien qualifié en conformité avec le code national de l’électricité et les règlements locaux.
-
Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en
position d’arrêt (« OFF »).
-
Placez l’interrupteur mural en position d’arrêt (« OFF »).
MISE EN GARDE
-
Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/CETL du luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression à la LED, tenir l’appareil par la seule base.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
-
Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta
lación de esta lámpara.
-
Sistema está disenado para ser instalado por un electricista calificado, de acuerdo con el código eléctrico nacional
y las normas locales.
-
Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali
mentación principal en la posición “OFF” (APAGADO).
-
Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
PRECAUCIÓN
-
Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calificación
ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.
HARDWARE
A1
Modern Forms
www.modernforms.com
Phone (800) 526.2588 • Fax (800) 526.2585
B1
Headquarters/Eastern Distribution Center
44 Harbor Park Drive • Port Washington, NY 11050
Phone (516) 515.5000 • Fax (516) 515.5050
C1
Western Distribution Center
1750 Archibald Ave • Ontario, CA 91761
Phone (800) 526.2588 • Fax (800) 526.2585
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. September, 2014
INSTALLATION INSTRUCTION
Ledge
WS-W1408, WS-W1414, WS-W1420
FIG.1
K1
C1
F1
A1
J1
G1
D1
B1
E1
M1
C1
PREPARATION
1. Shut off the power at the circuit breaker and remove existing fixture, including the crossbar.
2. Carefully unpack your new fixture and lay out all the parts on a clear area.
Be careful not to lose any small parts necessary for installation.
MOUNTING THE FIXTURE (Fig. 1)
3. Adjust the glass inside the frame before installation. Secure mounting backplate (D1) to the junction box (F1) using junction box
screws (B1).The side of the mounting backplate marked “GND” (E1) must face out.
*Requires Transformer to be recessed within the junction box
CONNECTING THE WIRES (Fig. 2)
4. Connect the electrical wires as shown in Fig. 2, making sure that all wire connectors (A1) are secured. If your outlet box has a
ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to
the backplate (D1) using the green screw (E1) provided. After wires are connected, tuck them carefully inside the junction box.
5. Place the fixture’s backplate over the mounting backplate (D1) and secure with screws (H1).Then secure the fixture with screws
(C1) and gasket (G1).
COMPLETING THE INSTALLATION (Fig. 3)
6. To prevent moisture from entering the outlet box and causing a short, use clear caulking (i.e. indoor/outdoor silicone sealant)
to outline the outside of fixture back plate where it meets the wall leaving a space at bottom to allow moisture a means to escape
Fig.2 Wiring
Fig.3 Sealing
Fixture Wires
Black or
Smooth
House Wires
Black
(Hot)
Fixture Wires
White or
Ribbed
House Wires
White
(Neutral)
Fixture Wires
Bare wire
(Ground)
House Wires
Green or Bare Copper
(Ground)
Modern Forms
www.modernforms.com
Phone (800) 526.2588 • Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive • Port Washington, NY 11050
Phone (516) 515.5000 • Fax (516) 515.5050
Junction Box
Caulking
Western Distribution Center
1750 Archibald Ave • Ontario, CA 91761
Phone (800) 526.2588 • Fax (800) 526.2585
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. September, 2014
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising