Wells | HDW-2 | Specifications | Wells HDW-2 Specifications

Wells HDW-2 Specifications
025
WELLS BLOOMFIELD, LLC
10 Sunnen Dr., St. Louis, MO 63143
telephone: 314-678-6314
fax: 314-781-2714
www.wellsbloomfield.com
OWNERS MANUAL
BUILT-IN
DISHER WELL
WARMER
MODELS
HDW-2
HDW-2D
Includes
INSTALLATION
USE & CARE
EXPLODED VIEW
PARTS LIST
WIRING DIAGRAM
HDW-2
IMPORTANT: DO NOT DISCARD THIS MANUAL
This manual is considered to be part of the appliance and is to be given to the OWNER or
MANAGER of the restaurant, or to the person responsible for TRAINING OPERATORS of
this appliance. Additional manuals are available from your WELLS DEALER.
THIS MANUAL MUST BE READ AND UNDERSTOOD BY ALL PERSONS USING OR
INSTALLING THIS APPLIANCE. Contact your WELLS DEALER if you have any
questions concerning installation, operation or maintenance of this equipment.
p/n 2M-Z14353 Rev. (A)
M025
120514
LIMITED WARRANTY STATEMENT
Unless otherwise specified, all commercial cooking
equipment manufactured by WELLS BLOOMFIELD, LLC is
warranted against defects in materials and workmanship
for a period of one year from the date of original installation
or 18 months from the date of shipment from our factory,
whichever comes first, and is for the benefit of the original
purchaser only.
The prices charged by Wells Bloomfield for its products
are based upon the limitations in this warranty. Seller’s
obligation under this warranty is limited to the repair of
defects without charge by a Wells Bloomfield factory
authorized service agency or one of its sub-service
agencies. This service will be provided on customer’s
premises for non-portable models. Portable models (a
device with a cord and plug) must be taken or shipped
to the closest authorized service agency, transportation
charges prepaid, for service. In addition to restrictions
contained in this warranty, specific limitations are shown in
the Service Policy and Procedure Guide. Wells Bloomfield
authorized service agencies are located in principal cities.
This warranty is valid in the United States and Canada and
void elsewhere. Please consult your classified telephone
directory, your foodservice equipment dealer or contact:
THIS WARRANTY IS THE COMPLETE AND ONLY
WARRANTY, EXPRESSED OR IMPLIED IN LAW
OR IN FACT, INCLUDING BUT NOT LIMITED TO,
WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR ANY PARTICULAR PURPOSE, AND/OR FOR
DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES IN
CONNECTION WITH WELLS BLOOMFIELD PRODUCTS.
This warranty is void if it is determined that, upon inspection
by an authorized service agency, the equipment has been
modified, misused, misapplied, improperly installed, or
damaged in transit or by fire, flood or act of God. It also
does not apply if the serial nameplate has been removed,
or if service is performed by unauthorized personnel.
Wells Bloomfield, LLC
10 Sunnen Dr., St. Louis MO 63143 USA
phone (314) 678-6314 or fax (314) 781-2714
for information and other details concerning warranty.
1.
2.
3.
4.
5.
6.
Resetting of safety thermostats, circuit breakers, over
load protectors, and/or fuse replacements are not
covered by this warranty unless warranted conditions
are the cause.
All problems due to operation at voltages or phase
other than specified on equipment nameplates are
not covered by this warranty.
Conversion to correct voltage and/or phase must be
the customer’s responsibility.
All problems due to electrical connections not made
in accordance with electrical code requirements
and wiring diagrams supplied with the equipment are
not covered by this warranty.
Replacement of items subject to normal wear, to
include such items as knobs, light bulbs; and, normal
maintenance functions including adjustments of
thermostats, adjustment of micro switches and
replacement of fuses and indicating lights are not
covered by warranty.
Damage to electrical cords and/or plug due to exposure
to excessive heat are not covered by this warranty.
Full use, care, and maintenance instructions supplied
with each machine. Noted maintenance and
preventative maintenance items, such as servicing and
cleaning schedules, are customer responsibility.
Those miscellaneous adjustments noted are customer
responsibility. Proper attention to preventative
maintenance and scheduled maintenance procedures
will prolong the life of the appliance.
7. Travel mileage is limited to sixty (50) miles from an
Authorized Service Agency or one of its sub-service
agencies.
8. All labor shall be performed during regular working
hours. Overtime premium will be charged to the buyer.
9. All genuine Wells replacement parts are warranted
for ninety (90) days from date of purchase on nonwarranty equipment. This parts warranty is limited only
to replacement of the defective part(s). Any use of
non-genuine Wells parts completely voids any
warranty.
10. Installation, labor, and job check-outs are not
considered warranty and are thus not covered by this
warranty.
11. Charges incurred by delays, waiting time or operating
restrictions that hinder the service technician’s ability to
perform service are not covered by warranty. This
includes institutional and correctional facilities.
SHIPPING DAMAGE CLAIM PROCEDURE
3.
NOTE: For your protection, please note that equipment
in this shipment was carefully inspected and packaged
by skilled personnel before leaving the factory. Upon
acceptance of this shipment, the transportation company
assumes full responsibility for its safe delivery.
IF SHIPMENT ARRIVES DAMAGED:
1. VISIBLE LOSS OR DAMAGE: Be certain that any
visible loss or damage is noted on the freight bill or
express receipt, and that the note of loss or damage is
signed by the delivery person.
2. FILE CLAIM FOR DAMAGE IMMEDIATELY:
Regardless of the extent of the damage.
CONCEALED LOSS OR DAMAGE: if damage is
unnoticed until the merchandise is unpacked, notify the
transportation company or carrier immediately, and file
“CONCEALED DAMAGE” claim with them. This
should be done within fifteen (15) days from the date
the delivery was made to you. Be sure to retain the
container for inspection.
Wells Bloomfield cannot assume liability for damage or loss
incurred in transit. We will, however, at your request, supply
you with the necessary documents to support your claim.
xi
M025 2M-Z14353 Owners Manual for Built-In Disher Well Warmer
SERVICE POLICY AND PROCEDURE GUIDE and ADDITIONAL WARRANTY EXCLUSIONS
TABLE OF CONTENTS
WARRANTY
FEATURES & OPERATING CONTROLS
PRECAUTIONS & GENERAL INFORMATION
AGENCY LISTING INFORMATION
INSTALLATION
OPERATION
MAINTENANCE INSTRUCTIONS
CLEANING INSTRUCTIONS
TROUBLESHOOTING SUGGESTIONS
WIRING DIAGRAM
EXPLODED VIEW & PARTS LIST
PARTS & SERVICE
CUSTOMER SERVICE DATA
xi
2
3
3
4
6
7
8-9
10
11
12-13
17
17
INTRODUCTION
Thank You for purchasing this Wells Bloomfield appliance.
M025 2M-Z14353 Owners Manual for Built-In Disher Well Warmer
Proper installation, professional operation and consistent maintenance of this appliance will ensure that it
gives you the very best performance and a long, economical service life.
This manual contains the information needed to properly install this appliance, and to use and care for the
appliance in a manner which will ensure its optimum performance.
SPECIFICATIONS
MODEL
VOLTS
AMPS
WATTS
POWER SUPPLY CORD
HDW-2, HDW-2D
120 VAC 1ø
2.5A
300W
NEMA 5-15 PLUG
1
FEATURES & OPERATING CONTROLS
Faucet
Stand Pipe &
Drian Overflow
(optional with some models)
Lighted
Power Switch
IL2157a
See Detail A
3/4” Drain
Power Cord
Nameplate
Detail A
A. CONTROLS
1. Units are equipped with a lighted power switch which illuminates when the
unit is turned on.
2. When the unit begins heating, fill the basin with water.
A temperature of 145°F to 160°F (62°C to 71°C) will be maintained.
B. MOUNTING
1. Units are equipped with Bowl Clamps (qty 3) which are designed to secure
the unit firmly in place on a stainless steel countertop.
NOTE:This appliance is designed to be used on stainless steel countertop only.
2.
See the Installation Instructions, supplied with the this appliance, for
details.
C. DRAINS
1. These units are equipped with an overflow drain and a Stand Pipe
Assembly. When the Stand Pipe is removed the entire bowl drains.
2
M025 2M-Z14353 Owners Manual for Built-In Disher Well Warmer
MOUNTING
BRACKET
PRECAUTIONS AND GENERAL INFORMATION
This appliance is intended for use in commercial establishments only.
This appliance is a perpetual-flow sink used to rinse utensils
being used for food preparation. No other use is recommended or
authorized by the manufacturer or its agents.
Operators of this appliance must be familiar with the appliance use,
limitations and associated restrictions. Operating instructions must be
read and understood by all persons using or installing this appliance.
Cleanliness of this appliance is essential to good sanitation. Read and
follow all included cleaning instructions and schedules to ensure the
safety of the food product.
Disconnect this appliance from electrical power before performing any
maintenance or servicing.
This appliance is not jet stream approved. Do not direct water jet
or steam jet at this appliance, or at any control panel or wiring. Do
not splash or pour water on, in or over any controls, control panel or
wiring.
Exposed surfaces of this appliance can be hot to the touch and may
cause burns.
M025 2M-Z14353 Owners Manual for Built-In Disher Well Warmer
Do not operate this appliance if the control panel is damaged.
Call your Authorized Wells Service Agent for service.
The technical content of this manual, including any wiring diagrams,
schematics, parts breakdown illustrations and/or adjustment
procedures, is intended for use by qualified technical personnel.
Any procedure which requires the use of tools must be performed by a
qualified technician.
This manual is considered to be a permanent part of the appliance.
This manual and all supplied instructions, diagrams, schematics,
parts breakdown illustrations, notices and labels must remain with the
appliance if it is sold or moved to another location.
WARNING:
WA
SHOCK HAZARD
SHO
All servicin
servicing requiring
access to non-insulated
electrical components must
be performed by a factory
authorized technician.
DO NOT open any access
panel which requires the use
of tools. Failure to follow this
warning can result in severe
electrical shock.
CAUTION:
CA
R
RISK
OF
DAMAGE
D
DO NOT connect or energize
this appliance until all
installation instructions are
read and followed. Damage
to the appliance may result
if these instructions are not
followed.
CAUTION:
CA
HOT SURFACE
Exposed su
surfaces can be hot
to the touch and may cause
burns.
This appliance is made in the USA. Unless otherwise noted, this
appliance has American sizes on all hardware.
AGENCY LISTING INFORMATION
Refer to the product nameplate for the specific appliance for agency
listings. In general:
STD 2
This appliance conforms to NSF Standard 2 for sanitation only if
installed in accordance with the supplied Installation Instructions.
UL Listed warmers are U Listed under UL File E27255.
E27255
UL Listed Warmers
3
INSTALLATION
WARNING:
WA
RISK OF INJURY
RIS
Installation procedures must
be performed by a qualified
technician with full knowledge
of all applicable electrical and
plumbing codes. Failure can
result in personal injury and
property damage.
UNPACKING & INSPECTION
Carefully remove the appliance from the carton. Remove all protective
plastic film, packing materials and accessories from the Appliance
before connecting electrical power or otherwise performing any
installation procedure.
Carefully read all instructions in this manual and the Installation
Instruction Sheet packed with the appliance before starting any
installation.
Read and understand all labels and diagrams attached to the
appliance.
Carefully account for all components and accessories before
discarding packing materials. Store all accessories in a convenient
place for later use.
INSTALLATION NOTES
1.
Installation and start up of built-in warmers MUST be performed
by an authorized installation company.
2.
It is the RESPONSIBILITY OF THE INSTALLER to verify that
this warmer installation is in compliance with the specifications listed in
this manual and on the specification sheet provided.
3.
It is the RESPONSIBILITY OF THE INSTALLER to check with
the AUTHORITY HAVING JURISDICTION, in order to verify
that this warmer installation is in compliance with local code
requirements.
4.
Water supply and drain installation must meet all applicable
local, state and federal plumbing codes and ordinances.
5.
Refer to Installation Instructions included with the warmer for
Underwriters Laboratories conditions of acceptability, electrical
requirements and other installation concerns.
CAUTION
CA
FIRE HAZARD
Avoid st
storing
in flammable or
combustible materials in, on
or near the appliance.
NOTE: Damage caused
by leaks due to improper
installation is NOT covered by
warranty.
OPTIONAL FAUCET
0.875” for Wells Supplied
Faucet Other Faucets
Sizes May Vary
3 1/8”
BUILT-IN WARMERS
1.
This is a GENERAL GUIDE. For specific cutout dimensions
and other installation details, refer to the Installation Instructions
supplied with the warmer.
2.
Cutout dimensions for disher well and optional faucet are listed on the
Installation Instructions provided with the warmer.
NOTE: Verify the dimensions are correct for the installation before
making the cutout.
3. Securing the disher well to a stainless steel countertop:
3 1/8”
45°
a. Verify that provided sealants are applied to the underside
of the warmer top flange prior to setting the unit into the cutout.
b. Units are equipped with Bowl Clamps (qty 3) which are designed
to secure the unit firmly in place on a stainless steel countertop.
6” Dia.
IL2159a
FRONT
c.
Apply a thin bead of food-grade silicone sealant around the
flange to seal it to the counter.
NOTE: IF THE WARMER IS INSTALLED ABOVE A FOOD STORAGE
CABINET. A SEALED BARRIER MUST BE PROVIDED BELOW THE
WARMER
4
M025 2M-Z14353 Owners Manual for Built-In Disher Well Warmer
NOTE: DO NOT discard
the carton or other packing
materials until you have
inspected the appliance for
hidden damage and tested it
for proper operation.
Refer to SHIPPING DAMAGE
CLAIM PROCEDURE on the
inside front cover of this
manual.
INSTALLATION
ELECTRICAL INSTALLATION
1. Refer to the product nameplate. Verify the electrical service power.
Voltage and phase must match the nameplate specifications.
Wiring the warmer to the wrong voltage can severely damage the
unit or cause noticeably decreased performance.
2. Available electrical service amperage must meet or exceed the
specifications listed on the specification sheet provided with the
warmer.
3.
Warmer and control unit must be connected to an appropriate
building ground. Ground connection will be marked “GND” or
”
“.
NOTE: Wire gauge, insulation type and temperature rating , as
well as type, size and construction of conduit, must meet or exceed
applicable specifications of local codes and of the National
Electrical Code.
E. PLUMBING INSTALLATION
For use in the State of Massachusetts, this appliance must be
installed in compliance with Massachusetts Fuel Gas and
Plumbing Code CMR 248.
M025 2M-Z14353 Owners Manual for Built-In Disher Well Warmer
1. IMPORTANT: All plumbing installations must be performed by
a qualified plumber.
2. These units are equipped with a 3/4” drain and will require a
DRAIN LINE: Some jurisdictions may require an approved air
gap or other back-flow prevention device in the drain. It is the
responsibility of the plumber to determine such requirement, to
provide and properly install the required device.
3. For HDW-2 units, the 3/4” drain must be attached with a union
at the drain line fitting. This is necessary to provide for future
maintenance to the unit.
5
CAUTION:
CA
SHOCK HAZARD
SHO
The ground lug of this
appliance must be connected
to a suitable building ground.
IMPORTANT:
Contact a licensed electrician
to install and connect electrical
power to the appliance.
IMPORTANT:
Damage due to being
connected to the wrong
voltage or phase is NOT
covered by warranty.
IMPORTANT: Electrical
installation other than as
specified on the specification
sheet will void the UL listing,
and may void the warranty.
NOTE: Plumb connections
must be made in compliance
with all Federal, State and
Local Plumbing Codes and
Ordinances.
NOTE: Damage caused
by leaks due to improper
installation is NOT covered by
warranty.
OPERATION
HOT SURFACE
Exposed surfaces can be hot
to the touch and may cause
burns.
CAUTION:
CA
SHOCK HAZARD
SHO
splash or pour water
DO NOT spl
onto control panel or wiring.
DO NOT place food directly
into the warmer.
DO NOT put ice into a
warmer pan. This will cause
condensation on the inside of
the warmer. Damage caused
by condensation is NOT
covered by warranty.
WET OPERATION for DISHER WELL
1. This unit is designed to be used for WET operation, add tap water
before turning the warmer on. Allow the disher well to preheat for
approximately 30 minutes prior to using.
a. Check the water level frequently and add water as necessary
to refresh the water in the basin, or to prevent the warmer from
running dry.
b. If your wet-operation warmer is allowed to run dry, turn it OFF and
allow to cool to room temperature before adding water.
4. Damage caused by allowing a wet-operation warmer to run dry,
is NOT covered by warranty. Damage caused by adding water
to a dry warmer when hot is NOT covered by warranty.
OPERATION
1. Use this appliance as a safe location to store and rinse your
utensils, DO NOT place food directly into the warmer.
2. Check water level in the warmer frequently during use.
3. DO NOT use metal tools, steel wool, or caustic or abrasive cleanser to
clean warmer pan.
M025 2M-Z14353 Owners Manual for Built-In Disher Well Warmer
CAUTION:
CA
6
MAINTENANCE INSTRUCTIONS
CARE OF STAINLESS STEEL
Stainless steel is a marvelous material: strong, lustrous and low maintenance. With
a minimum of care, it will normally retain its beauty and durability for the life of the
equipment. In some applications, however, special care is required in order to maintain
stainless steel’s special properties.
External components, such as cabinets and control panels, are finished with a grain
pattern. This pleasing finish is best maintained by cleaning with a non-abrasive
cleanser applied with a soft cloth. Rub only in the direction of the grain. In the absence
of visible grain, rub only along the longest axis of the appliance.
Restore stainless steel’s luster by applying a polish specifically made for stainless steel.
Spray on, wipe off with a soft cloth, rubbing in the direction of the grain.
Never use metal implements, wire brushes, abrasive scratch pads or steel
wool to clean stainless steel.
M025 2M-Z14353 Owners Manual for Built-In Disher Well Warmer
Warmer pans, insets and other vessels are subject to a harsher environment. Wells
Manufacturing uses an very high quality stainless steel (#304DDQ) for our food warmer
pans. Even the highest quality stainless steel, however, is mostly iron, and will rust, pit
and corrode under the following conditions:
•
•
Poor Water Quality: Hard water (water with a high content of dissolved minerals) will leave mineral deposits when allowed to dry. Calcium (lime) can buildup on
heated surfaces, even under water. If left unattended, hard water spots and lime
buildup can lead to rusting, corrosion and pitting.
Contact with Chlorides: Chlorides (specific compounds of chlorine) are found in
food, table salt and many cleansers. Chlorides can attack the surface of stainless
steel, resulting in corrosion and pitting.
Keep your stainless steel warmers clean and free from calcium buildup.
Use alkaline, alkaline chlorinated or non-chloride cleanser.
Use citric acid-based cleaners to remove calcium deposits.
For additional information, please read the NAFEM Stainless Steel Equipment and
Cleaning Guide. Contact NAFEM at :
North American Association of Food Equipment Manufacturers
401 N. Michigan Avenue
Chicago, Illinois 60611-4267
(312) 644-6610
7
CLEANING INSTRUCTIONS
CAUTION:
CA
SHOCK HAZARD
SHO
splash or pour water
Do NOT spl
into or over any control panel
or wiring.
DAILY CLEANING INSTRUCTIONS
PREPARATIONS: Turn main power switch to OFF. Allow warmer to
cool before proceeding.
Remove any insets, utinsils and/or inserts.
Drain or remove water from well..
FREQUENCY:
Minimum - daily.
TOOLS:
Mild Detergent
Solution: 10 Parts Warm Water to 4 Parts Vinegar
Plastic Scouring Pad
Clean Cloth or Sponge
Food-Grade Silicone Sealant
SHOCK HAZARD
SH
Disconnect warmer from
electric power before cleaning
CAUTION:
CA
BURN HAZARD
BU
Allow
Allo warmer to cool
completely before cleaning.
1.
Wipe entire unit down using a clean cloth or sponge and mild
detergent.
2.
Use a plastic scouring pad to remove any hardened food particles
or mineral deposits.
IMPORTANT: DO NOT use steel wool for cleaning.
3.
Rinse warmer thoroughly with a vinegar and water solution to
neutralize all detergent cleanser residue.
4.
Inspect warmer flange-to-counter seal. Reseal with food-grade
silicone sealant if necessary. Failure to do so may allow grease and
water to leak into insulation and heating element, causing a potential
fire and/or electric shock hazard.
5.
Clean the Stand-Pipe (drain/overflow assy) and insert using mild
detergnet and warm water.
6.
Install the Stand-Pipe & insert, add proper amount of water and
rinse the basin. Turn the main power switch ON and check for proper
operation.
Procedure Complete.
8
M025 2M-Z14353 Owners Manual for Built-In Disher Well Warmer
CAUTION:
CA
CLEANING INSTRUCTIONS
CAUTION:
CA
MONTHLY CLEANING INSTRUCTIONS
PREPARATIONS: Remove any insets, utinsils.
Drain or remove water from well.
FREQUENCY:
Weekly, or whenever lime or scale is seen
accumulating on the sides of the warmer pans.
TOOLS:
Commercial Delime Cleaner
Plastic Scouring Pad
Clean Cloth or Sponge
1.
Add water to pans until water is at normal operating level
or covers accumulated scale.
2. Heat water to maximum temperature (145ºF).
3. Pour contents of one package of commercial delime cleaner
into each basin. Stir to dissolve cleaner. Turn heat control OFF.
4.
Allow solution to soak at least one hour, or overnight for heavy
scale buildup.
5.
Drain water from well. Scrub with a plastic scouring pad.
Rinse thoroughly with hot water, then dry.
6. Refill pans with tap water and resume operation.
M025 2M-Z14353 Owners Manual for Built-In Disher Well Warmer
7. Heavy scale buildup may require additional treatments.
9
CH
CHEMICAL
BURN
HAZARD
HA
Deilim
Deilimng chemicals
he
may be
caustic. Wear appropriate
personal protective equipment.
Follow cleaner manufacturer’s
instructions for safest use.
TROUBLESHOOTING SUGGESTIONS
SYMPTOM
POSSIBLE CAUSE
SUGGESTED REMEDY
No power to warmer
Circuit breaker off or tripped
Reset circuit breaker
Warmer will not heat
Temperature control not set
Set control to desired temperature
Wet insulation
Verify flange-to counter seal is sound, or
reseal with food-grade silicone sealant
Pan leaking or other internal damage
Contact your Authorized Wells Service
Agency for repairs
Internal damage
Contact your Authorized Wells Service
Agency for repairs
Mineral deposits on pan acting as a
insulator
Clean pan(s) with delime cleaner
Wired to wrong voltage
Verify supply voltage - must match
voltage on warmer nameplate
Drain valve not fully closed
Check drain valve for debris and close
fully
Drain valve damaged or pan(s) leaking
Contact your Authorized Wells Service
Agency for repairs
Warmer trips circuit breaker
Warmer slow to heat
Drain-equipped unit will not hold
water
M025 2M-Z14353 Owners Manual for Built-In Disher Well Warmer
There are no user-serviceable components in this appliance.
In all instances of damage or malfunction, contact your Authorized Wells Service Agency for repairs.
10
WIRING DIAGRAM
3
7
POWER
SWITCH
THERMOSTAT
HIGH LIMIT
THERMOSTAT
8
1
M025 2M-Z14353 Owners Manual for Built-In Disher Well Warmer
5
2
6
HEATING
ELEMENT
4
WHITE
BLACK
GROUND
HDW-2 Wiring Diagram
SK2488
11
EXPLODED VIEW: HDW-2 DISHER WELL
1
2
3
4
5
22
23
24
20
11
21
6
16
7
19
18
17
8
9
10
11
12
11
15
Model: HDW-2 DISHER WELL
14
13
SK2489, Rev. A, 2/21/2012
12
M025 2M-Z14353 Owners Manual for Built-In Disher Well Warmer
20
PARTS LIST: HDW-2 DISHER WELL
July 20, 2012
Model: HDW-2 Dipper Well
Fig No
1
M025 2M-Z14353 Owners Manual for Built-In Disher Well Warmer
2
Part No
P2-Z14195
Qty
1
2
Description
Applications
HDW-2
WELL INSERT
HDW-2D
2V-Z15955
1
STAND PIPE ASSEMBLY
HDW-2
2V-Z15955
2
STANDPIPE ASSY
HDW-2D
1
HDW-2
3
2I-Z14209
4
P2-WL0183
1
WELL ASSEMBLY
5
2K-Z14206
1
FAUCET, DIPPER
6
P2-Z15039
1
ELEMENT, PLATE
7
2N-Z14199
1
ELEMENT 300W 120V
8
2C-Z14325
1
WASHER FLAT .75OD X .344ID COPPER
9
2T-Z14200
1
THERMOSTAT
10
P2-Z14190
1
CLAMP, THERMOSTAT
11
2C-Z6929
12
P2-Z14196
1
HOUSING, ELEMENT
13
2K-H5417
1
BUSHING, HEYCO #SR-6P-3-4
14
P2-Z14191
1
COVER, CONTROL
15
2C-6349
2
SCREW #8 x 3/8 B THP STL NP
16
P2-WL0198
1
CORDSET HDW-2
17
2C-1494
1
SCREW #8 -32 X .5 RH NP
18
P2-Z14506
1
BRACKET - HIGH LIMIT
19
2T-Z14503
1
THERMOSTAT 325°F
20
2C-73457
5
8-32 KEPS NUT SS
21
P2-Z14189
3
CLAMP BOWL
22
2M-Z14204
1
LABEL - WELLS LOGO AND CAUTION
23
2E-Z14201
1
SWITCH, STST-LIGHTED
24
P2-Z14193
1
WIRE CHANNEL
4
7
9
O-RING
HDW-2D
10-24 KEPS NUT S.S.
13
INCLUDED WITH HDW-2D
HDW-2
HDW-2D
NOTES
14
M025 2M-Z14353 Owners Manual for Built-In Disher Well Warmer
M025 2M-Z14353 Owners Manual for Built-In Disher Well Warmer
NOTES
15
NOTES
16
M025 2M-Z14353 Owners Manual for Built-In Disher Well Warmer
PARTS & SERVICE
DESCRIPTION
PART NO.
IMPORTANT: Use only
factory authorized service parts
and replacement filters.
For factory authorized
service, or to order factory
authorized replacement parts,
contact your Wells authorized
service agency, or call:
Wells Bloomfield, LLC
10 Sunnen Dr.,
St. Louis MO 63143 USA
Service Dept.
phone: (314) 678-6314
fax:
(314) 781-2714
M025 2M-Z14353 Owners Manual for Built-In Disher Well Warmer
Service Parts Department
can supply you with the name
and telephone number of
the WELLS AUTHORIZED
SERVICE AGENCY
nearest you.
CUSTOMER SERVICE DATA
please have this information available if calling for service
RESTAURANT _____________________________ LOCATION _____________
INSTALLATION DATE ________________________ TECHNICIAN ___________
SERVICE COMPANY ________________________________________________
ADDRESS ___________________________ STATE ______ ZIP__________
TELEPHONE NUMBER (_____)_____-_________
EQUIPMENT MODEL NO. _______________
EQUIPMENT SERIAL NO. _______________
VOLTAGE:(checkone)
120
208
17
240
WELLS BLOOMFIELD, LLC
10 Sunnen Dr., St. Louis, MO 63143
telephone: 314-678-6314
fax: 314-781-2714
www.wellsbloomfield.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising