B-4998 Swing-Up Grab Bar Installation Instructions

B-4998 Swing-Up Grab Bar Installation Instructions
INSTALLATION INSTRUCTIONS
BOBRICK MODEL B-4998 AND B-4998.99 WALL MOUNTED SWING-UP GRAB BARS
Finish Face of Wall
8-3/4''
220mm
Stud
61''
1550mm
6-1/8''
155mm
Bumper
1/2''
13mm
S
Provide
Adequate
Backing
29''
735mm
8-3/4''
220mm
S
7-3/4''
195mm
S
Grab Bar Backplate
S
34''
865mm
33''
From Top
Mounting
Screws
840mm
1/2''
13mm
Mounting
Holes (4)
S
5-1/8''
130mm
S
Finish Face of Floor
Figure 1
Figure 2
Important Notes: Mounting Height and Wall Preparation
4HEMOUNTINGHEIGHTSHOWNINTHESEINSTRUCTIONSISBASEDON!MERICAN.ATIONAL3TANDARD)NSTITUTE3PECIlCATION!.3)!ANDISPROVIDED
only as a guide. Check local building codes for grab bar mounting height to make sure installation complies with local code requirement.
'RAB"ARSARENOSTRONGERTHANTHEANCHORSORWALLSTOWHICHTHEYAREATTACHED4HEYMUSTBESECURELYMOUNTEDTOSUSTAINALOADOFLBSATANY
POINT3TUDSARETOBEREINFORCEDANDADEQUATEBACKINGMUSTBEMOUNTEDTOTHESTUDSBEFORETHElNISHEDWALLSURFACEISAPPLIEDTOPROVIDESECUREATTACHMENTOFTHEGRABBARTOTHEWALL4HEINSTALLATIONMUSTCOMPLYWITHLOCALBUILDINGCODEREQUIREMENTS
ALTERNATE METHODS OF INSTALLATION
Installation with Bobrick Mounting Kit Available as an Accessory
1. Reinforce wall studs prior to attachment of Bobrick anchor plate.
&ASTENSTEELANCHORPLATETOSTUDSMAKINGSUREITISPLUMBANDSQUARE-OUNTTOPOFANCHORPLATEggMMABOVElNISHEDmOOR4HISWILL
LOCATETHECENTERLINEOFTHETOPBARINTHEHORIZONTALPOSITIONATggMMABOVElNISHEDmOOR
3. Mounting screws should be temporarily screwed into anchor plate at points marked by an S BEFOREAPPLICATIONOFlNISHEDWALLSURFACESOTHAT
the location of the mounting screw holes can be found for mounting the grab bar to the wall.
!PPLYlNISHEDWALLSURFACETOWALL
5. Remove mounting screws from wall. Mount grab bar, making sure screws are tight.
4ESTGRABBARMAKINGCERTAINITREMAINSINBOTHTHEVERTICALSTORAGEPOSITIONANDTHEHORIZONTALUSEPOSITION
Installation with Backing Furnished by Installer
1. Make certain backing meets local codes.
2. Reinforce wall studs prior to attachment of adequate backing.
3. Install adequate backing in wall at locations indicated in Figure 1. Allow for either #14 size screws, or in the case of steel backing 1/4-20
STAINLESSSTEELSCREWSOFADEQUATELENGTHNEITHERAREFURNISHEDBY"OBRICK4HESTEELBACKINGMUSTHAVEAMINIMUMTHICKNESSOFgg
MMANDSCREWHOLESBEDRILLEDANDTAPPED
4. Use grab bar back plate as a template to mark mounting screw hole locations.
5. After mounting grab bar make certain it remains in both the vertical storage position and the horizontal use position.
Installation to Solid Masonry Walls
5SEINSERTSLEADSHIELDSOREQUIVALENTFORSCREWSNOTFURNISHEDBY"OBRICKANDMOUNTATHEIGHTINDICATEDIN&IGUREORPERLOCALCODE
using grab bar back plate as template to mark mounting screw hole location.
2. After mounting grab bar, make certain it remains in both vertical storage position and the horizontal use position.
In the U.S.A.: BOBRICK WASHROOM EQUIPMENT, INC.
#OMMERCE$RIVE#LIFTON0ARK.EW9ORKs4ELs&!8
(ART3TREET.ORTH(OLLYWOOD#ALIFORNIAs4ELs&!8
© 2010 by Bobrick Washroom Equipment, Inc.
Form No. 4998-69 r12/29/10 QA010511 Printed in U.S.A.
In Canada: BOBRICK WASHROOM EQUIPMENT COMPANY
2OLARK$RIVE3CARBOROUGH/NTARIO-2"s/NTARIO%AST4EL&!8
s-ANITOBA7EST4EL&!8
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising