HMC913

Design Assistance

Customised Pack Sizes / Qtys

Assembly Assistance

Support for all industry recognised
supply formats:

Die handling consultancy

Hi-Rel die qualification

Hot & Cold die probing

Electrical test & trimming
o Waffle Pack
o Gel Pak
o Tape & Reel

Onsite storage, stockholding &
scheduling

100% Visual Inspection
o MIL-STD 883 Condition A
o MIL-STD 883 Condition A

On-site failure analysis

Bespoke 24 Hour monitored
storage systems for secure long
term product support

On-site failure analysis
Contact
baredie@micross.com
For price, delivery and to place orders
HMC913
www.analog.com
www.micross.com
Analog Devices Welcomes
Hittite Microwave Corporation
NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED
www.analog.com
www.hittite.com
THIS PAGE INTENTIONALLY LEFT BLANK
HMC913
v04.0913
SDLVAs - CHIP
SUCCESSIVE DETECTION LOG VIDEO
AMPLIFER (SDLVA), 0.6 - 20 GHz
Typical Applications
Features
The HMC913 is ideal for:
High Logging Range: 59 dB
(-54 to +5 dBm) @ 18 GHz
• EW, ELINT & IFM Receivers
Output Frequency Flatness: ±1.5 dB
• DF Radar Systems
Log Linearity: ±1 dB
• ECM Systems
• Broadband Test & Measurement
• Power Measurement & Control Circuits
• Military & Space Applications
Functional Diagram
Fast Rise/Fall Times: 5/10 ns
Single Positive Supply: +3.3V
ESD Sensitivity (HBM): Class 1A
General Description
The HMC913 is a Successive Detection Log Video
Amplifier (SDLVA) which operates from 0.6 to 20 GHz.
The HMC913 provides a logging range of 59 dB. This
device offers typical fast rise/fall times of 5/10 ns and
a superior delay time of only 14 ns. The HMC913 log
video output slope is typically 14 mV/dB. Maximum
recovery times are less than 30 ns. Ideal for high
speed channelized receiver applications, the HMC913
operates from a single +3.3 V supply, and consumes
only 80 mA. All data shown herein is measured with
the chip in a 50 Ohm environment and contacted with
RF probes.
Electrical Specifications, TA = +25 °C, Vcc1 = Vcc2 = 3.3V [1]
Parameter
Conditions
Typ.
Units
0.6 - 20
GHz
±1.5
dB
Pin = -50 to +3 dBm
±1
dB
Pin = -25 dBm
±1.5
dB
Minimum Logging Range
to ±3 dB error @ 18 GHz
-54 @ 18 GHz
dBm
Maximum Logging Range
to ±3 dB error @ 18 GHz
+5 @ 18 GHz
dBm
5.5
dB
Log Video Minimum Output Voltage
1
V
Log Video Maximum Output Voltage
1.8
V
Input Frequency Range [1][2]
Frequency Flatness
Log Linearity
Log Linearity over Temperature (-55 °C to +85 °C)
Pin = -25 dBm
Input Return Loss
Log Video Output Rise Time
10% to 90%
5
ns
Log Video Output Fall Time
90% to 10%
10
ns
Log Video Recovery Time
25
ns
Log Video Output Slope
14
mV/dB
5
µV/dB°C
Log Video Output Slope Variation over Temperature
@ 10 GHz
Log Video Propagation Delay
Supply Current (Icc1 + Icc2)
@ Pin = -30 dBm
14
ns
80
mA
[1] Electrical specs and performance plots are given for single-ended operation
[2] Video output load should be 1K Ohm or higher.
1
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
HMC913
v04.0913
SUCCESSIVE DETECTION LOG VIDEO
AMPLIFER (SDLVA), 0.6 - 20 GHz
VIDEO OUT & Error
vs. Input Power, Fin = 500 MHz [1]
5
2 GHz
6 GHz
10 GHz
14 GHz
18 GHz
20 GHz
3
2
ERR +25C
ERR +85C
ERR -55C
1
0
-1
-2
2
1
1.5
0
-1
1
-3
Ideal
Video Out +25C
Video Out +85C
Video Out -55C
-4
-5
-70
-60
-50
-40
-30
-20
-10
0
10
-70
20
-60
-50
VIDEO OUT & Error
vs. Input Power, Fin = 1 GHz [1]
3
Ideal
Video Out +25C
Video Out +85C
Video Out -55C
VIDEO OUT (V)
-1
1
-10
0
10
1
1.5
0
-1
1
-2
-70
-60
-50
3
0
10
ERR +25C
ERR +85C
ERR -55C
20
-1
1
Ideal
Video Out +25C
Video Out +85C
Video Out -55C
0
10
1
1.5
0
-1
1
Ideal
Video Out +25C
Video Out +85C
Video Out -55C
-2
-3
0.5
2
20
INPUT POWER (dBm)
-2
-3
0.5
-70
ERROR (dB)
0
VIDEO OUT (V)
1
1.5
-10
-10
3
2
-20
-20
2
ERROR (dB)
VIDEO OUT (V)
ERR +25C
ERR +85C
ERR -55C
-30
-30
VIDEO OUT & Error
vs. Input Power, Fin = 10 GHz [1]
2
-40
-40
INPUT POWER (dBm)
VIDEO OUT & Error
vs. Input Power, Fin = 6 GHz [1]
-50
-2
-3
0.5
20
INPUT POWER (dBm)
-60
20
2
Ideal
Video Out +25C
Video Out +85C
Video Out -55C
-3
0.5
-70
10
ERROR (dB)
0
-20
0
ERR +25C
ERR +85C
ERR -55C
1
-30
-10
3
2
1.5
-40
-20
2
ERROR (dB)
VIDEO OUT (V)
ERR +25C
ERR +85C
ERR -55C
-50
-30
VIDEO OUT & Error
vs. Input Power, Fin = 2 GHz [1]
2
-60
-40
INPUT POWER (dBm)
INPUT POWER (dBm)
-70
-2
-3
0.5
-6
ERROR (dB)
VIDEO OUT (V)
4
ERROR (dB)
3
2
6
SDLVAs - CHIP
Error Flatness vs.
Input Power Over Frequency [1][2]
-60
-50
-40
-30
-20
-10
0
10
20
INPUT POWER (dBm)
[1] Electrical specs and performance plots are given for single-ended operation
[2] An average ideal line is used to calculate error curves.
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
2
HMC913
v04.0913
SUCCESSIVE DETECTION LOG VIDEO
AMPLIFER (SDLVA), 0.6 - 20 GHz
VIDEO OUT vs. Error
vs. Input Power, Fin = 18 GHz [1]
VIDEO OUT & Error
vs. Input Power, Fin = 14 GHz [1]
0
-1
1
Ideal
Video Out +25C
Video Out +85C
Video Out -55C
VIDEO OUT (V)
1
1.5
-70
-60
-50
-40
-30
-20
-10
0
10
1
1.5
0
-1
1
Ideal
Video Out +25C
Video Out +85C
Video Out -55C
-2
0.5
-3
0.5
2
-70
20
-60
-50
-40
-30
-20
-10
0
10
-2
-3
20
INPUT POWER (dBm)
INPUT POWER (dBm)
VIDEO OUT & Error
vs. Input Power, Fin = 20 GHz [1]
3
2
2
1
1.5
0
-1
1
Ideal
Video Out +25C
Video Out +85C
Video Out -55C
ERROR (dB)
VIDEO OUT (V)
ERR +25C
ERR +85C
ERR -55C
-2
-3
0.5
-70
-60
-50
-40
-30
-20
-10
0
10
20
INPUT POWER (dBm)
VIDEO OUT vs. Frequency
Over Input Power & Bias Voltage [1]
VIDEO OUT vs. Frequency
Over Input Power & Temperature [1]
1.8
1.8
+25C
+85C
-55C
1.7
VIDEO OUT (V)
1.5
1.4
-25 dBm
1.3
1.2
1.5
-25 dBm
1.4
1.3
1.2
-40 dBm
-40 dBm
1.1
1.1
1
-10 dBm
1.6
VIDEO OUT (V)
-10 dBm
1.6
3.15V
3.30V
3.45V
1.7
0
2
4
6
8
10
12
14
16
18
20
22
FREQUENCY (GHz)
1
0
2
4
6
8
10
12
14
16
18
20
22
FREQUENCY (GHz)
[1] Electrical specs and performance plots are given for single-ended operation
3
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
ERROR (dB)
VIDEO OUT (V)
ERR +25C
ERR +85C
ERR -55C
2
ERROR (dB)
SDLVAs - CHIP
ERR +25C
ERR +85C
ERR -55C
3
2
3
2
HMC913
v04.0913
SUCCESSIVE DETECTION LOG VIDEO
AMPLIFER (SDLVA), 0.6 - 20 GHz
1.8
1.8
1.6
1.6
1.4
2 GHz
10 GHz
18 GHz
1.2
1
0.8
1.4
1.2
2 GHz
10 GHz
18 GHz
1
0
20
40
60
80
0.8
100
0
20
40
TIME (ns)
60
80
100
TIME (ns)
SDLVAs - CHIP
Fall Time for Various Frequencies
@ 0 dBm [1]
VIDEO OUT (V)
VIDEO OUT (V)
Rise Time for Various Frequencies
@ 0 dBm [1]
Input Return Loss vs. Frequency [1]
RETURN LOSS (dB)
0
-5
-10
-15
-20
0
5
10
15
20
25
30
FREQUENCY (GHz)
[1] Electrical specs and performance plots are given for single-ended operation
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
4
HMC913
v04.0913
SUCCESSIVE DETECTION LOG VIDEO
AMPLIFER (SDLVA), 0.6 - 20 GHz
SDLVAs - CHIP
Absolute Maximum Ratings
Vcc
+3.6V
ENBL
+3.6V
RF Input Power
+15 dBm
Channel Temperature
125 °C
Continuous Pdiss (T=85°C)
Derate 12.63 mW/°C above 85°C
0.51 W
Thermal Resistance Rth
(Junction to die bottom)
33.94 °C/W
Storage Temperature
-65 to +150 °C
Operating Temperature
-55 to +85 °C
ESD Sensitivity (HBM)
Class 1A
Die Packaging Information
[1]
Standard
Alternate
WP-3 (Waffle Pack)
[2]
[1] Refer to the “Packaging Information” section for die
packaging dimensions.
[2] For alternate packaging information contact Hittite
Microwave Corporation.
NOTES:
1. ALL DIMENSIONS IN INCHES [MILLIMETERS]
2. DIE THICKNESS IS 0.011 (0.279)
3. TYPICAL BOND PAD IS 0.0024 SQUARE
4. BOND PAD METALLIZATION: ALUMINUM
5. NO BACKSIDE METAL
6. NO CONNECTION REQUIRED FOR UNLABELED BOND PADS
7. OVERALL DIE SIZE IS ±.002
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
Outline Drawing
5
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
HMC913
v04.0913
SUCCESSIVE DETECTION LOG VIDEO
AMPLIFER (SDLVA), 0.6 - 20 GHz
Pad Descriptions
Function
1-5
VCC1
Description
Interface Schematic
Bias Supply. Connect Supply Voltage to these pins
with appropriate filtering.
To ensure proper start-up supply
rise time should be faster than 100usec
SDLVAs - CHIP
Pad Number
Bias Supply. Connect supply voltage to these pins
with appropriate filtering.
6
VCC2
7
EN
Enable pin connected to VCC1 or VCC2 for normal
operation. Total supply current reduced to less than 3mA
when EN is set to 0V.
8, 11 - 18, 21, 22
Die Bottom
GND
These pins and the die bottom must be connected to a high
quality RF/DC ground.
9, 10
VIDEO OUT,
VIDEO FB
Video out and feedback. These pins should be shorted to
each other (see application circuit). Video out load should
be at least 1K Ohm or higher.
To ensure proper start-up supply
rise time should be faster than 100usec
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
6
HMC913
v04.0913
SUCCESSIVE DETECTION LOG VIDEO
AMPLIFER (SDLVA), 0.6 - 20 GHz
SDLVAs - CHIP
Pad Descriptions (Continued)
Pad Number
Function
Description
19, 20
RFINN, RFINP
RF Input pins Connect RF to RFINP and AC
couple RFINN to ground via 50 Ohm for single ended
operation.
Interface Schematic
Application Circuit
Note: Video output load should be 1K Ohm or higher.
7
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
HMC913
v04.0913
SUCCESSIVE DETECTION LOG VIDEO
AMPLIFER (SDLVA), 0.6 - 20 GHz
SDLVAs - CHIP
Assembly Diagram
List of Materials for Assembly Diagram
Item
Description
C1, C2
33 pF Capacitor, 0402 Pkg.
C3 - C6
100 pF SLC Capacitor, SA1212BX101M16VHXF
C7 - C8
10 nF SLC Capacitor, MVB3030X103ZGH5N
R1
50 Ohm Resistor, 0402 Pkg.
U1
HMC913 Die
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
8
HMC913
v04.0913
SUCCESSIVE DETECTION LOG VIDEO
AMPLIFER (SDLVA), 0.6 - 20 GHz
SDLVAs - CHIP
Mounting & Bonding Techniques for MMICs
The die should be attached directly to the ground plane with epoxy (see HMC general Handling, Mounting , Bonding Note).
50 Ohm Microstrip transmission lines on 0.254mm (10 mil) thick alumina thin film
substrates are recommended for bringing RF to and from the chip (Figure 1).
Microstrip substrates should be placed as close to the die as possible in order to
minimize bond wire length. Typical die-to-substrate spacing is 0.076mm to 0.152
mm (3 to 6 mils).
0.279mm (0.011”) Thick MMIC
Wire Bond
0.076mm
(0.003”)
Handling Precautions
RF Ground Plane
Follow these precautions to avoid permanent damage.
Storage: All bare die are placed in either Waffle or Gel based ESD protective containers, and then sealed in an ESD protective bag for shipment. Once the sealed
ESD protective bag has been opened, all die should be stored in a dry nitrogen
environment.
0.254mm (0.010”) Thick Alumina
Thin Film Substrate
Figure 1.
Cleanliness: Handle the chips in a clean environment. DO NOT attempt to clean
the chip using liquid cleaning systems.
Static Sensitivity: Follow ESD precautions to protect against ESD strikes.
Transients: Suppress instrument and bias supply transients while bias is applied. Use shielded signal and bias cables to minimize
inductive pick-up.
General Handling: The chip may be handled by a vacuum collet or with a sharp pair of tweezers.
Mounting
Epoxy Die Attach: Apply a minimum amount of epoxy to the mounting surface so that a thin epoxy fillet is observed around the
perimeter of the chip once it is placed into position. Cure epoxy per the manufacturer’s schedule.
9
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising