CyberData | 011186 | Operations Guide |  VoIP V3 Outdoor Intercom Operations Guide 011186

 VoIP V3 Outdoor Intercom Operations Guide 011186
The IP Endpoint Company
VoIP V3 Outdoor Intercom
Operations Guide
Part #011186
Document Part #930472J
for Firmware Version 8.0.0
CyberData Corporation
3 Justin Court
Monterey, CA 93940
(831) 373-2601
VoIP V3 Outdoor Intercom Operations Guide 930472J
Part # 011186
COPYRIGHT NOTICE:
© 2015, CyberData Corporation, ALL RIGHTS RESERVED.
This manual and related materials are the copyrighted property of CyberData Corporation. No part of
this manual or related materials may be reproduced or transmitted, in any form or by any means
(except for internal use by licensed customers), without prior express written permission of
CyberData Corporation. This manual, and the products, software, firmware, and/or hardware
described in this manual are the property of CyberData Corporation, provided under the terms of an
agreement between CyberData Corporation and recipient of this manual, and their use is subject to
that agreement and its terms.
DISCLAIMER: Except as expressly and specifically stated in a written agreement executed by
CyberData Corporation, CyberData Corporation makes no representation or warranty, express or
implied, including any warranty or merchantability or fitness for any purpose, with respect to this
manual or the products, software, firmware, and/or hardware described herein, and CyberData
Corporation assumes no liability for damages or claims resulting from any use of this manual or such
products, software, firmware, and/or hardware. CyberData Corporation reserves the right to make
changes, without notice, to this manual and to any such product, software, firmware, and/or
hardware.
OPEN SOURCE STATEMENT: Certain software components included in CyberData products are
subject to the GNU General Public License (GPL) and Lesser GNU General Public License (LGPL)
“open source” or “free software” licenses. Some of this Open Source Software may be owned by third
parties. Open Source Software is not subject to the terms and conditions of the CyberData
COPYRIGHT NOTICE or software licenses. Your right to copy, modify, and distribute any Open
Source Software is determined by the terms of the GPL, LGPL, or third party, according to who
licenses that software.
Software or firmware developed by CyberData that is unrelated to Open Source Software is
copyrighted by CyberData, subject to the terms of CyberData licenses, and may not be copied,
modified, reverse-engineered, or otherwise altered without explicit written permission from
CyberData Corporation.
TRADEMARK NOTICE: CyberData Corporation and the CyberData Corporation logos are
trademarks of CyberData Corporation. Other product names, trademarks, and service marks may be
the trademarks or registered trademarks of their respective owners.
Technical Support 

The IP Endpoint Company The fastest way to get technical support for your VoIP product is to
submit a VoIP Technical Support form at the following website:
http://support.cyberdata.net/

Phone: (831) 373-2601, Ext. 333
Email: support@cyberdata.net
Fax: (831) 373-4193
Company and product information is at www.cyberdata.net.
CyberData Corporation
930472J
Operations Guide
Revision Information
Revision 930472J, which corresponds to firmware version 8.0.0, was released on October 20, 2015,
and has the following changes:
•
•
Operations Guide
Updates the following specifications in Table 1-1, "Specifications":
•
Power Input: PoE 802.3af compliant or +8 to +12VDC @ 1000mA Regulated Power Supply
•
Speaker Output: 1 Watt Peak Power
•
On-Board Relay: 1A at 30 VDC
•
Dimensions: 5.118 inches [130 mm] Length, 2.252 inches [57.21 mm] Width, 5.118 inches
[130 mm] Height
•
Weight: 2.0 lbs. (0.90 kg)
•
Boxed Weight: 2.0 lbs. (0.91 kg)
Updates Figure 2-2, "Intercom Connections"
930472J
CyberData Corporation
Pictorial Alert Icons
General Alert
This pictoral alert indicates a potentially hazardous situation. This alert will be
followed by a hazard level heading and more specific information about the
hazard.
GENERAL ALERT
Ground
This pictoral alert indicates the Earth grounding connection point.
Hazard Levels
Danger: Indicates an imminently hazardous situation which, if not avoided, will result in death or
serious injury. This is limited to the most extreme situations.
Warning: Indicates a potentially hazardous situation which, if not avoided, could result in death or
serious injury.
Caution: Indicates a potentially hazardous situation which, if not avoided, could result in minor or
moderate injury. It may also alert users against unsafe practices.
Notice: Indicates a statement of company policy (that is, a safety policy or protection of property).
The safety guidelines for the equipment in this manual do not purport to address all the safety issues
of the equipment. It is the responsibility of the user to establish appropriate safety, ergonomic, and
health practices and determine the applicability of regulatory limitations prior to use. Potential safety
hazards are identified in this manual through the use of words Danger, Warning, and Caution, the
specific hazard type, and pictorial alert icons.
CyberData Corporation
930472J
Operations Guide
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has
two blades with one wider than the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
13. Prior to installation, consult local building and electrical code requirements.
14. WARNING: The VoIP Intercom enclosure is not rated for any AC voltages!
Warning
Electrical Hazard: This product should be installed by a licensed electrician
according to all local electrical and building codes.
GENERAL ALERT
Warning
Electrical Hazard: To prevent injury, this apparatus must be securely attached to
the floor/wall in accordance with the installation instructions.
GENERAL ALERT
Warning
The PoE connector is intended for intra-building connections only and does not
route to the outside plant.
GENERAL ALERT
CyberData Corporation
930472J
Operations Guide
Contents
i
Chapter 1 Product Overview
1
1.1 How to Identify This Product .....................................................................................................1
1.2 Typical System Installation .......................................................................................................2
1.3 Product Features ......................................................................................................................4
1.4 Supported Protocols .................................................................................................................5
1.5 Supported SIP Servers .............................................................................................................5
1.6 Specifications ...........................................................................................................................6
Chapter 2 Installing the VoIP V3 Outdoor Intercom
7
2.1 Parts List ..................................................................................................................................7
2.2 Intercom Components ..............................................................................................................8
2.3 Intercom Setup .........................................................................................................................9
2.3.1 Intercom Connections ....................................................................................................9
2.3.2 Connecting the Intercom to the On-Board Relay .........................................................10
2.3.3 Intercom Connectors ....................................................................................................12
2.3.4 Activity and Link LEDs .................................................................................................14
2.3.5 RTFM Button ................................................................................................................15
2.3.6 Adjusting the Intercom Volume .....................................................................................16
2.3.7 Call Button and the Call Button LED ............................................................................17
2.4 Configure the Intercom Parameters ......................................................................................18
2.4.1 Factory Default Settings ...............................................................................................18
2.4.2 Intercom Web Page Navigation ....................................................................................19
2.4.3 Log in to the Configuration Home Page .......................................................................20
2.4.4 Configure the Device ....................................................................................................23
2.4.5 Configure the Network Parameters .............................................................................26
2.4.6 Configure the SIP Parameters .....................................................................................28
2.4.7 Configure the Nightringer Parameters ..........................................................................33
2.4.8 Configure the Sensor Configuration Parameters ..........................................................35
2.4.9 Configure the Multicast Parameters .............................................................................38
2.4.10 Configure the Audio Configuration Parameters ..........................................................40
2.4.11 Configure the Event Parameters ................................................................................45
2.4.12 Configure the Autoprovisioning Parameters ...............................................................50
2.5 Upgrade the Firmware and Reboot the Intercom ...................................................................55
2.5.1 Uploading the Firmware ...............................................................................................55
2.5.2 Reboot the Intercom .....................................................................................................57
2.6 Command Interface ................................................................................................................58
2.6.1 Command Interface Post Commands ..........................................................................58
Appendix A Mounting the Intercom
62
A.1 Mounting Components ...........................................................................................................62
A.2 Dimensions ............................................................................................................................63
A.3 Overview of Installation Types ................................................................................................66
A.4 Network Cable Entry Restrictions ..........................................................................................67
A.4.1 Side Conduit Network Cable Entry Restrictions ..........................................................67
A.4.2 Rear Conduit Network Cable Entry Restrictions (without Shroud) ..............................68
A.4.3 Rear Conduit Network Cable Entry Restrictions (with Shroud) ...................................68
A.5 Ground Cable Installation .......................................................................................................69
A.6 Service Loop Cable Routing ..................................................................................................70
A.7 Securing the Intercom ............................................................................................................71
A.8 Additional Mounting Options ..................................................................................................72
A.8.1 Conduit Mounting Option (Not Provided) .....................................................................72
A.8.2 Concrete Wall Mounting Option (Not Provided) ...........................................................73
A.8.3 Goose Neck Mounting Option (Not Provided) ..............................................................74
A.8.4 Ground Cable Installation for Goose Neck Mounting Option .......................................75
Appendix B Setting up a TFTP Server
76
B.1 Set up a TFTP Server ............................................................................................................76
B.1.1 In a LINUX Environment ..............................................................................................76
Operations Guide
930472J
CyberData Corporation
ii
B.1.2 In a Windows Environment .........................................................................................76
Appendix C Troubleshooting/Technical Support
77
C.1 Frequently Asked Questions (FAQ) ........................................................................................77
C.2 Documentation .......................................................................................................................77
C.3 Contact Information ................................................................................................................78
C.4 Warranty and RMA Information ..............................................................................................78
Index
Operations Guide
79
930242G
CyberData Corporation
1
1 Product Overview
1.1 How to Identify This Product
To identify the VoIP V3 Outdoor Intercom, look for a model number label similar to the one shown in 
Figure 1-1. The model number on the label should be 011186.
Figure 1-1. Model Number Label
WWW.CYBERDATA.NET
INTERCOM,V3 VoIP OUTDOOR, PoE, WITH
INTRUSION DETECTION, RoHS
011186 / 021078C
186000001
Model number
Operations Guide
930472J
CyberData Corporation
Product Overview 2
Typical System Installation
1.2 Typical System Installation
The Voice-over-IP (VoIP) Intercom is a SIP endpoint designed to provide VoIP phone connectivity in
a tamper-proof and secure package.
Figure 1-2, Figure 1-3, and Figure 1-4 illustrate how the VoIP V3 Outdoor Intercoms can be installed
as part of a VoIP phone system.
Figure 1-2. Typical Installation—Door Entry/Access Control
802.3af Compliant Ethernet Switch
1
V3 Intercom
2
V3 Intercom
3
4
5
6
V3 Intercom
IP Phone
IP PBX Server
Figure 1-3. Typical Installation—Mass Notification
Generic PoE Switch
1
Speaker
Loudspeaker
Amplifier
2
Strobe
Light
3
4
5
6
V3 Intercom
IP Phone
IP PBX Server
Figure 1-4. Typical Installation—Emergency Phone
Generic PoE Hub
1
VoIP Intercom
Operations Guide
IP Phone
2
3
4
IP Phone
930472J
5
6
IP Phone
IP PBX Server
CyberData Corporation
Product Overview 3
Typical System Installation
Warning
Electrical Hazard: The VoIP V3 Outdoor Intercom enclosure is not rated for any
AC voltages.
GENERAL ALERT
Warning
Electrical Hazard: This product should be installed by a licensed electrician
according to all local electrical and building codes.
GENERAL ALERT
Warning
Electrical Hazard: To prevent injury, this apparatus must be securely attached to
the floor/wall in accordance with the installation instructions.
GENERAL ALERT
Warning
The PoE connector is intended for intra-building connections only and does not
route to the outside plant.
GENERAL ALERT
Operations Guide
930472J
CyberData Corporation
Product Overview 4
Product Features
1.3 Product Features
The VoIP V3 Outdoor Intercom has the following features:
Operations Guide
•
Supports SRST (Survivable Remote Site Telephony) in a Cisco environment. SRST parameters
are entered statically into the CyberData product's internal webpage.
•
SIP
•
Dual speeds of 10 Mbps and 100 Mbps
•
802.3af compliant
•
2 gang outlet box size
•
Adaptive full duplex voice operation
•
Network/Web management
•
Network adjustable speaker volume adjustment
•
Network configurable door or intrusion sensor settings
•
Network configurable relay activation settings
•
Dial Out Extension supports the addition of comma delimited pauses before sending additional
DTMF tones
•
Network configurable microphone input sensitivity adjustment
•
Network downloadable product firmware
•
Doubles as a paging speaker
•
Call button
•
Call activity indicator (light)
•
Tamper proof design
•
One dry contact relay for auxiliary control
•
Autoprovisioning
•
Configurable audio files
•
Night Ringer
•
Peer-to-peer capable
•
Door closure and tamper alert signal
•
Optional Torx screws with driver kit
•
An active call is indicated by the Call Button LED blinking at one second intervals.
930472J
CyberData Corporation
Product Overview 5
Supported Protocols
1.4 Supported Protocols
The Intercom supports the following protocols:
•
SIP
•
HTTP Web-based configuration
Provides an intuitive user interface for easy system configuration and verification of Intercom
operations.
•
DHCP Client
Dynamically assigns IP addresses in addition to the option to use static addressing.
•
TFTP Client
Facilitates hosting for the Autoprovisioning configuration file.
•
RTP
•
RTP/AVP - Audio Video Profile
•
Facilitates autoprovisioning configuration values on boot
•
Audio Encodings
PCMU (G.711 mu-law)
PCMA (G.711 A-law)
Packet Time 20 ms
1.5 Supported SIP Servers
Go to the following link to find the VoIP V3 Outdoor Intercom product page which will have
information on how to configure the device for various supported SIP servers:
http://www.cyberdata.net/support/server/index.html
Operations Guide
930472J
CyberData Corporation
Product Overview 6
Specifications
1.6 Specifications
Table 1-1. Specifications
Specifications
Ethernet I/F
10/100 Mbps
Protocol
SIP RFC 3261 Compatible
Power Input
PoE 802.3af compliant or +8 to +12VDC @ 1000mA Regulated Power Supplya
Speaker Output
1 Watt Peak Power
On-Board Relay
1A at 30 VDC
Operating Temperature
-10° C to 50° C (14° F to 122° F)
Payload Types
G711, A-law and µ-law
Regulatory Compliance
FCC Class A, UL 60950-1 / UL 60065-1
Dimensions
5.118 inches [130 mm] Length
2.252 inches [57.21 mm] Width
5.118 inches [130 mm] Height
Weight
2.0 lbs. (0.90 kg)
Boxed Weight
3.0 lbs. (1.36 kg)
Part Number
011186
011188 Weather Shroud (sold separately)
a. Contacts 1 and 2 on the J3 terminal block are only for powering the device from a non-PoE 12VDC
power source as an alternative to Network PoE power. Use of these contacts for any other purpose will
damage the device and void the product warranty.
Operations Guide
930472J
CyberData Corporation
7
2 Installing the VoIP V3 Outdoor Intercom
2.1 Parts List
Table 2-1 illustrates the VoIP V3 Outdoor Intercom parts.
Table 2-1. Parts List
Quantity Part Name
Operations Guide
Illustration
1
Intercom Assembly
1
Installation Quick Reference Guide
1
Intercom Mounting Accessory Kit
930472J
CyberData Corporation
Installing the VoIP V3 Outdoor Intercom 8
Intercom Components
2.2 Intercom Components
Figure 2-1 shows the components of the Intercom .
Figure 2-1. Intercom Components
Microphone Hole
Speaker Drain Hole
Call Button
See Section 2.3.7, "Call Button
and the Call Button LED" for 
information about the functionality
of the Call Button.
Operations Guide
930472J
CyberData Corporation
Installing the VoIP V3 Outdoor Intercom 9
Intercom Setup
2.3 Intercom Setup
2.3.1 Intercom Connections
Figure 2-2 shows the pin connections on the J3 (terminal block). This terminal block can accept 
16 AWG gauge wire.
Note
As an alternative to using PoE power, you can supply +8 to +12VDC @ 1000mA Regulated
Power Supply into the terminal block.
Caution
GENERAL ALERT
Equipment Hazard: Contacts 1 and 2 on the J3 terminal block are only for
powering the Intercom from a non-PoE 12VDC power source as an alternative to
Network PoE power. Use of these contacts for any other purpose will damage the
Intercom and void the product warranty.
Figure 2-2. Intercom Connections
Alternate Power Input:
1 = +8 to +12VDC @ 1000mA Regulated Power Supply*
2 = Power Ground*
Wire (IN)
3
4
Terminal Block
can accept
16 AWG wire
Relay Contact:
(1 A at 30 VDC for continuous loads)
3 = Normally Open Common
4 = Normally Open Contact
5 = Door Sense Input
6 = Door Sense Ground Reference
1
6
*Contacts 1 and 2 on the J3 terminal block are only
for powering the device from a non-PoE 12VDC power
source as an alternative to Network PoE power. Use of
these contacts for any other purpose will damage the
device and void the product warranty.
Operations Guide
930472J
J3 Terminal Block
CyberData Corporation
Installing the VoIP V3 Outdoor Intercom 10
Intercom Setup
2.3.2 Connecting the Intercom to the On-Board Relay
Warning
Electrical Hazard: The VoIP V3 Outdoor Intercom enclosure is not rated for
any AC voltages.
GENERAL ALERT
Warning
Electrical Hazard: This product should be installed by a licensed electrician
according to all local electrical and building codes.
GENERAL ALERT
Warning
Electrical Hazard: To prevent injury, this apparatus must be securely attached
to the floor/wall in accordance with the installation instructions.
GENERAL ALERT
Warning
Electrical Hazard: The relay contacts are dry and provided for a normally
open and momentarily closed configuration. Neither the alternate power input
nor PoE power can be used to drive a door strike.
GENERAL ALERT
Warning
The PoE connector is intended for intra-building connections only and does not
route to the outside plant.
GENERAL ALERT
The VoIP Intercom incorporates an on-board relay which enables users to control an external relay
for activating an auxiliary device such as an electric door strike (see Figure 2-3, "On-Board Relay
Wiring Diagram").
The Intercom relay contacts are limited to 1A at 30 VDC. The Intercom relay activation time is
selectable through the web interface and is controlled by DTMF tones generated from the phone
being called. The DTMF tones are selectable from the web interface as well.
Note
Operations Guide
The three digit code for the on-board relay must be sent in conformance with RFC2833
DTMF generation.
930472J
CyberData Corporation
CyberData Corporation
Example of External Relay (not supplied)
Controlled Device
Such As
Electric Door Strike
or
Strobe Light
Solid State
or
Mechanical
Relay
OUT
High PIV UltraFast
Switching Diode
IN
Output Contacts
AC or DC rated
Depending Upon
Controlled Device
Requirements
-
DC
POWER SUPPLY
MAX.
30 VDC @ 1A
(
)
+
6
5
4
3
2
1
930472J
AC or DC
Power Source
Intercom PCB
On-Board Relay Wiring Contacts
Operations Guide
Installing the VoIP V3 Outdoor Intercom 11
Connecting the Intercom to the On-Board Relay
Figure 2-3. On-Board Relay Wiring Diagram
Installing the VoIP V3 Outdoor Intercom 12
Intercom Setup
2.3.3 Intercom Connectors
See the following figures and tables to identify the connectors and functions of the Intercom.
Figure 2-4. Connector Locations
J10
J2
J6
J7
Table 2-2. Connector Functions
Operations Guide
Connector
Function
J2
Call Button. LED Interface
J6
Microphone Interface
J7
Speaker Interface
J10
Proximity Sensor Interface - N/A
930472J
CyberData Corporation
Installing the VoIP V3 Outdoor Intercom 13
Intercom Setup
Figure 2-5. Connector Locations
Table 2-3. Connector Functions
Operations Guide
Connector
Function
J1
PoE Network Connection (RJ-45 ethernet)
J3
Terminal Block (see Figure 2-2)
J4
Factory Only—Console Port
J5
Factory Only—JTAG
JP1
Factory Only—Reset
JP5
Factory Only—Watch Dog
JP7
Factory Only—Boot Mode
JP10
Disables the intrusion sensor when installed.
930472J
CyberData Corporation
Installing the VoIP V3 Outdoor Intercom 14
Intercom Setup
2.3.4 Activity and Link LEDs
2.3.4.1 Verifying the Network Connectivity and Data Rate
When you plug in the Ethernet cable or power supply to the Intercom, the following occurs:
•
The square, YELLOW Activity light blinks when there is network activity (see Figure 2-6).
•
The square, GREEN Link light above the Ethernet port indicates that the network connection
has been established (see Figure 2-6).
Figure 2-6. Activity and Link LED
Link
Activity
Operations Guide
930472J
CyberData Corporation
Installing the VoIP V3 Outdoor Intercom 15
Intercom Setup
2.3.5 RTFM Button
When the Intercom is operational and linked to the network, you can use the Reset Test Function
Management (RTFM) button (see SW1 in Figure 2-7) on the Intercom board to announce and
confirm the Intercom’s IP Address and test to see if the audio is working.
Note
You must do these tests prior to final assembly.
Figure 2-7. RTFM Button (SW1)
2.3.5.1 Announcing the IP Address
To announce a device’s current IP address:
1. Press and release the RTFM button (see SW1 in Figure 2-8) within a five second window.
Note
The device will use DHCP to obtain the new IP address (DHCP-assigned address or default
to 10.10.10.10 if a DHCP server is not present).
Note
Pressing and holding the RTFM button for longer than five seconds will restore the device to
the factory default settings.
Figure 2-8. RTFM Button (SW1)
Operations Guide
930472J
CyberData Corporation
Installing the VoIP V3 Outdoor Intercom 16
Intercom Setup
2.3.5.2 Restoring the Factory Default Settings
When troubleshooting configuration problems, it is sometimes convenient to restore the device to a
known state.
Note
Each Intercom is delivered with factory set default values.
To restore the factory default settings:
1. Press and hold the RTFM button (see SW1 in Figure 2-9) for more than five seconds.
2. The device announces that it is restoring the factory default settings.
Note
The device will use DHCP to obtain the new IP address (DHCP-assigned address or default
to 10.10.10.10 if a DHCP server is not present).
Figure 2-9. RTFM Button
2.3.6 Adjusting the Intercom Volume
You can adjust the Intercom volume through the Speaker Volume setting on the Device
Configuration Page.
Operations Guide
930472J
CyberData Corporation
Installing the VoIP V3 Outdoor Intercom 17
Intercom Setup
2.3.7 Call Button and the Call Button LED
2.3.7.1 Calling with the The Call Button
•
You may initiate a call by pressing the Call button.
•
An active call is indicated by the Call Button LED blinking at one second intervals.
•
The Intercom can automatically answer an incoming call.
•
You can press the Call button to terminate an active call whether the call was an incoming call or
a call that was initiated by you.
2.3.7.2 Call Button LED Function
•
Upon initial power or reset, the Call Button LED will illuminate.
•
When the software has finished initialization, the Call Button LED will blink twice.
•
When a call is established (not just ringing), the Call Button LED will blink.
•
On the Device Configuration Page (see Section 2.4.4, "Configure the Device"), there is an
option called Button Lit When Idle. This option sets the normal state for the indicator light. The
Call Button LED will still blink during initialization and calls.
•
The Call Button LED flashes briefly at the beginning of RTFM mode.
Figure 2-10. Call Button and Call Button LED
Call Button and Call Button LED
Operations Guide
930472J
CyberData Corporation
Installing the VoIP V3 Outdoor Intercom 18
Intercom Setup
2.4 Configure the Intercom Parameters
To configure the Intercom online, use a standard web browser.
Configure each Intercom and verify its operation before you mount it. When you are ready to mount
an Intercom, refer to Appendix A, "Mounting the Intercom" for instructions.
2.4.1 Factory Default Settings
All Intercoms are initially configured with the following default IP settings:
When configuring more than one Intercom, attach the Intercoms to the network and configure one at
a time to avoid IP address conflicts.
Table 2-4. Factory Default Settings
Parameter
Factory Default Setting
IP Addressing
DHCP
IP Address
a
10.10.10.10
Web Access Username
admin
Web Access Password
admin
Subnet Maska
255.0.0.0
a
Default Gateway
10.0.0.1
a. Default if there is not a DHCP server present.
Operations Guide
930472J
CyberData Corporation
Installing the VoIP V3 Outdoor Intercom 19
Intercom Setup
2.4.2 Intercom Web Page Navigation
Table 2-5 shows the navigation buttons that you will see on every Intercom web page.
Table 2-5. Web Page Navigation
Web Page Item
Description
Link to the Home page.
Link to the Device Configuration page.
Link to the Networking page.
Link to go to the SIP Configuration page.
Link to go to the Nightringer page.
Link to the Sensor Configuration page.
Link to the Multicast Configuration page.
Link to the Audio Configuration page.
Link to the Event Configuration page.
Link to the Autoprovisioning Configuration
page.
Link to the Update Firmware page.
Operations Guide
930472J
CyberData Corporation
Installing the VoIP V3 Outdoor Intercom 20
Intercom Setup
2.4.3 Log in to the Configuration Home Page
1. Open your browser to the Intercom IP address.
Note
If the network does not have access to a DHCP server, the device will default to an IP
address of 10.10.10.10.
Note
Make sure that the PC is on the same IP network as the Intercom.
Note
You may also download CyberData’s VoIP Discovery Utility program which allows you to
easily find and configure the default web address of the CyberData VoIP products. 

CyberData’s VoIP Discovery Utility program is available at the following website address:
http://www.cyberdata.net/support/voip/discovery.html
Note
The Intercom ships in DHCP mode. To get to the Home page, use the discovery utility to
scan for the device on the network and open your browser from there.
2. When prompted, use the following default Web Access Username and Web Access
Password to access the Home Page (Figure 2-11):
Web Access Username: admin
Web Access Password: admin
Operations Guide
930472J
CyberData Corporation
Installing the VoIP V3 Outdoor Intercom 21
Intercom Setup
Figure 2-11. Home Page
Operations Guide
930472J
CyberData Corporation
Installing the VoIP V3 Outdoor Intercom 22
Intercom Setup
3. On the Home Page, review the setup details and navigation buttons described in Table 2-6.
Table 2-6. Home Page Overview
Web Page Item
Description
Device Settings
Device Name
Shows the device name.
Change Username
Type in this field to change the username.
Change Password
Type in this field to change the password.
Re-enter Password
Type the password again in this field to confirm the new password.
Current Settings
Serial Number
Shows the device serial number.
Mac Address
Shows the device Mac address.
Firmware Version
Shows the current firmware version.
IP Addressing
Shows the current IP addressing setting (DHCP or static).
IP Address
Shows the current IP address.
Subnet Mask
Shows the current subnet mask address.
Default Gateway
Shows the current default gateway address.
DNS Server 1
Shows the current DNS Server 1 address.
DNS Server 2
Shows the current DNS Server 2 address.
Speaker Volume
Shows the current speaker volume level.
Microphone Gain
Shows the current microphone gain level.
SIP Mode is
Shows the current status of the SIP mode.
Multicast Mode is
Shows the current status of the Multicast mode.
Event Reporting is
Shows the current status of the Event Reporting mode.
Nightringer is
Shows the current status of the Nightringer mode.
Primary SIP Server
Shows the current status of the Primary SIP Server.
Backup Server 1
Shows the current status of Backup Server 1.
Backup Server 2
Shows the current status of Backup Server 2.
Import/Export Settings
Press the Browse button to select a configuration file to import.
Press the Import Configuration button to save a board configuration
to the board. 
Note: The board will have to be reset before changes will take effect.
Press the Export Configuration button to download the current board
configuration.
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Click on the Reboot button to reboot the system.
Operations Guide
930472J
CyberData Corporation
Installing the VoIP V3 Outdoor Intercom 23
Intercom Setup
2.4.4 Configure the Device
1. Click the Device Configuration button to open the Device Configuration page. See Figure 212.
Figure 2-12. Device Configuration Page
Operations Guide
930472J
CyberData Corporation
Installing the VoIP V3 Outdoor Intercom 24
Intercom Setup
2. On the Device Configuration page, you may enter values for the parameters indicated in
Table 2-7.
Table 2-7. Device Configuration Parameters
Web Page Item
Description
Volume Settings
Speaker Volume
Type the desired Intercom volume level into this field.
Microphone Gain
Type the desired microphone gain level into this field.
Relay Settings
Activate Relay with DTMF Code
When selected, the relay can be activated with a DTMF
code.
DTMF Activation Code
Type the desired DTMF activation code 
(25 character limit).
DTMF Activation Duration (in seconds)
Type the desired DTMF activation duration (in seconds) (2
character limit [activation times now go up to 99 seconds]).
NOTE: A DTMF activation duration of 0 will toggle the
relay indefinitely or until the activation code is sent again
Play tone during DTMF Activation
When selected, the device will play a tone when the relay
is activated with a DTMF code.
Activate Relay During Ring
When selected, the relay will be activated for as long as
the call is active.
NOTE: When the phone is set to Auto Answer, it will not
ring and this option does nothing.
Activate Relay During Night Ring
Check this box to activate the relay for as long as a Night
Ring tone is ringing.
Activate Relay While Call Active
When selected, the relay will be activated for as long as
the call is active.
Activate Relay on Button Press
When selected, the relay will be activated when the Call
Button is pressed.
Relay on Button Press Timeout (in seconds) Type the desired time (in seconds) that you want the relay
to activate after the Call Button is pressed (1 character
limit).
Miscellaneous Settings
Auto-Answer Incoming Calls
When selected, the device will automatically answer
incoming calls.
When Auto Answer is Off, the device will play a ringtone
through the Intercom speaker until someone presses the
button.
Operations Guide
Button Lit When Idle
When selected, the Call Button remains lit when idle.
Play Ringback Tone
When selected, you will hear a ringback tone while making
a call.
930472J
CyberData Corporation
Installing the VoIP V3 Outdoor Intercom 25
Intercom Setup
Table 2-7. Device Configuration Parameters (continued)
Web Page Item
Description
Enable Push to Talk
This option is for noisy environments. When enabled, the
microphone will be muted normally. When the button is
pressed and held, it will unmute the microphone and allow
the operator to send audio back.
NOTE: When Enable Push to Talk is enabled, you cannot
stop an active call with the call button. The device on the
other end will need to end the call.
NOTE: Enable Push to Talk will not work on some older
hardware.
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Click on the Test Audio button to do an audio test. When
the Test Audio button is pressed, you will hear a voice
message for testing the device audio quality and volume.
Click on the Test Microphone button to do a microphone
test. When the Test Microphone button is pressed, the
following occurs:
1. The device will immediately start recording 3 seconds of
audio.
2. The device will beep (indicating the end of recording).
3. The device will play back the recorded audio.
Click on the Test Relay button to do a relay test.
Click on the Reboot button to reboot the system.
3. After changing the parameters, click the Save button.
Operations Guide
930472J
CyberData Corporation
Installing the VoIP V3 Outdoor Intercom 26
Intercom Setup
2.4.5 Configure the Network Parameters
1. Click the Networking button to open the Network Configuration page (Figure 2-13).
Figure 2-13. Network Configuration Page
Operations Guide
930472J
CyberData Corporation
Installing the VoIP V3 Outdoor Intercom 27
Intercom Setup
2. On the Network Configuration page, enter values for the parameters indicated in Table 2-8.
Table 2-8. Network Configuration Parameters
Web Page Item
Description
Stored Network Settings
IP Addressing
Select either DHCP IP Addressing or Static IP Addressing by
marking the appropriate radio button. If you select Static, configure
the remaining parameters indicated in Table 2-8. If you select DHCP,
go to Step 3.
IP Address
Enter the Static IP address.
Subnet Mask
Enter the Subnet Mask address.
Default Gateway
Enter the Default Gateway address.
DNS Server 1
Enter the DNS Server 1 address.
DNS Server 2
Enter the DNS Server 2 address.
DHCP Timeout
DHCP Timeout in seconds
Enter the desired timeout duration (in seconds) that the device will
wait for a response from the DHCP server before defaulting back to
the stored static IP address.
Note: A value of -1 will cause the device to retry indefinitely and a
value of 0 will cause the device to reset to a default of 60 seconds.
Current Network Settings
Shows the current network settings.
IP Address
Shows the current Static IP address.
Subnet Mask
Shows the current Subnet Mask address.
Default Gateway
Shows the current Default Gateway address.
DNS Server 1
Shows the current DNS Server 1 address.
DNS Server 2
Shows the current DNS Server 2 address.
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Click on the Reboot button to reboot the system.
3. After changing the parameters, click Save Settings. This updates the changed parameters and
reboots the Intercom if appropriate.
4. Connect the Intercom to the target network.
5. From a system on the same network as the Intercom, open a browser with the new IP address
of the Intercom.
Operations Guide
930472J
CyberData Corporation
Installing the VoIP V3 Outdoor Intercom 28
Intercom Setup
2.4.6 Configure the SIP Parameters
1. Click SIP Config to open the SIP Configuration page (Figure 2-14).
Note
For specific server configurations, go to the following website address:
http://www.cyberdata.net/support/server/index.html
Figure 2-14. SIP Configuration Page
Operations Guide
930472J
CyberData Corporation
Installing the VoIP V3 Outdoor Intercom 29
Intercom Setup
2. On the SIP Configuration page, enter values for the parameters indicated in Table 2-9.
Table 2-9. SIP Configuration Parameters
Web Page Item
Description
Enable SIP Operation
Enables or disables SIP operation.
SIP Settings
Primary SIP Server
Use this field to set the address (in dotted decimal notation or
as a canonical name) for the Primary SIP Server. This field
can accept canonical names of up to 255 characters in length.
Primary SIP User ID
Type the SIP User ID for the Primary SIP Server 
(up to 64 alphanumeric characters).
Primary Auth ID
Type the Authenticate ID for the Primary SIP Server
(up to 64 alphanumeric characters).
Primary Auth Password
Type the Authenticate Password for the Primary SIP Server
(up to 64 alphanumeric characters).
Backup SIP Server 1
• If all of the Primary SIP Server and Backup SIP Server
fields are populated, the device will attempt to stay registered
with all three servers all of the time. You can leave the
Backup SIP Server 1 and Backup SIP Server 2 fields blank
if they are not needed.
Backup SIP Server 2
• In the event of a registration failure on the Primary SIP
Server, the device will use the next highest priority server for
outbound calls (Backup SIP Server 1). If Backup SIP
Server 1 fails, the device will use Backup SIP Server 2.
• If a higher priority SIP Server comes back online, the device
will switch back to this server.
Type the SIP User ID for the Backup SIP Server 
(up to 64 alphanumeric characters).
Backup SIP User ID 1
Backup SIP User ID 2
Type the SIP Authenticate ID for the Backup SIP Server 
(up to 64 alphanumeric characters).
Backup SIP Auth ID 1
Backup SIP Auth ID 2
Backup SIP Auth Password 1
Type the SIP Authenticate Password for the Backup SIP
Server (up to 64 alphanumeric characters).
Backup SIP Auth Password 2
Use Cisco SRST
When selected, the backup servers are handled according to
Cisco SRST (Survivable Remote Site Telephony).
Remote SIP Port
Type the Remote SIP Port number (default 5060) 
(8 character limit).
Local SIP Port*
Type the Local SIP Port number (default 5060) 
(8 character limit).
Outbound Proxy
Type the Outbound Proxy as either a numeric IP address in
dotted decimal notation or the fully qualified host name 
(255 character limit [FQDN]).
Outbound Proxy Port
Type the Outbound Proxy Port number (8 character limit).
Register with a SIP Server
Check this box to enable SIP Registration.
For information about Point-to-Point Configuration, see
Section 2.4.6.2, "Point-to-Point Configuration".
Re-registration Interval (in seconds)
Operations Guide
Type the SIP Registration lease time (in seconds)
930472J
CyberData Corporation
Installing the VoIP V3 Outdoor Intercom 30
Intercom Setup
Table 2-9. SIP Configuration Parameters (continued)
Web Page Item
Description
Call Disconnection
Terminate call after delay (in seconds) Type the desired number of seconds that you want to transpire
after a connection delay before a call is terminated.
Note: A value of 0 will disable this function.
RTP Settings
RTP Port (even)
Specify the port number used for the RTP stream after
establishing a SIP call. This port number has to be an even
number and defaults to 10500.
Dial Out Settings
Dial Out Extension
Type the dial out extension number (64 character limit).
Note: For information about dial-out extension strings and
DTMF tones, see Section 2.4.6.1, "Dial Out Extension Strings
and DTMF Tones (using rfc2833)".
Extension ID
Type the desired Extension ID (64 character limit).
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Click on the Reboot button to reboot the system.
3. After changing the parameters, click Save Settings.
2.4.6.1 Dial Out Extension Strings and DTMF Tones (using rfc2833)
On the SIP Configuration Page, dial out extensions support the addition of comma delimited
pauses and sending additional DTMF tones (using rfc2833). The first comma will pause three
seconds after a call is first established with a remote device. Subsequent commas will pause for 2
seconds. A pause of one second will be sent after each numerical digit.
Table 2-10. Examples of Dial-Out Extension Strings
Extension String
Resulting Action
302
Dial out extension 302 and establish a call
302,2
Dial out extension 302 and establish a call, wait 3 seconds then send the
DTMF tone '2'
302,25,,,4,,1
Dial out extension 302 and establish a call, wait 3 seconds then send the
DTMF tone '2', send out DTMF tone 5, wait 6 seconds, send out DTMF
tone 4, wait 4 seconds, send out DTMF tone 1
Note
Operations Guide
The maximum number of total characters in the dial-out field is 64.
930472J
CyberData Corporation
Installing the VoIP V3 Outdoor Intercom 31
Intercom Setup
2.4.6.2 Point-to-Point Configuration
When the board is set to not register with a SIP server (see Figure 2-15), it's possible to set the
intercom to dial out to a single endpoint.
In this case, the dial-out extension should be the IP address of the remote device. The Intercom can
also receive Point-to-Point calls. The delayed DTMF functionality is available in the Point-to-Point
Mode.
Note
Receiving point-to-point SiP calls may not work with all phones.
Figure 2-15. SIP Configuration Page Set to Point-to-Point Mode
Intercom is set to NOT register with a SiP server
Operations Guide
930472J
CyberData Corporation
Installing the VoIP V3 Outdoor Intercom 32
Intercom Setup
2.4.6.3 Delayed DTMF
On the SIP Configuration page the dial out extension supports the addition of comma delimited
pauses and sending additional DTMF tones (using rfc2833). The first comma will pause three
seconds after a call is first established with a remote device. Subsequent commas will pause for 2
seconds. A pause of one second will be sent after each numerical digit.
Table 2-11. Examples of Dial-Out Extension Strings
Extension String
Resulting Action
302
Dial out extension 302 and establish a call
302,2
Dial out extension 302 and establish a call, wait 3 seconds then send the
DTMF tone '2'
302,25,,,4,,1
Dial out extension 302 and establish a call, wait 3 seconds then send the
DTMF tone '2', send out DTMF tone 5, wait 6 seconds, send out DTMF
tone 4, wait 4 seconds, send out DTMF tone 1
Note
Operations Guide
The maximum number of total characters in the dial-out field is 25.
930472J
CyberData Corporation
Installing the VoIP V3 Outdoor Intercom 33
Intercom Setup
2.4.7 Configure the Nightringer Parameters
When the Nightringer is enabled, the Intercom will register as a second SIP extension. Registration
does not have to be to the same server as the primary SIP registration. Any calls made to the
Nightringer extension will cause the Intercom to play a ring tone. There is no way to answer this call.
The Nightringer is designed to be used in buildings where calls made after hours are directed to a
ring group.
Caution
Nightringer requires SIP Registration. Nightringer cannot be used in peer to peer
mode.
GENERAL ALERT
1. Click on the Nightringer button to open the Nightringer Configuration page. See Figure 2-16.
Figure 2-16. Nightringer Configuration Setup
Operations Guide
930472J
CyberData Corporation
Installing the VoIP V3 Outdoor Intercom 34
Intercom Setup
2. On the Nightringer Configuration page, enter values for the parameters indicated
in Table 2-12.
Table 2-12. Nightringer Configuration Parameters
Web Page Item
Description
Enable Nightringer
When the nightringer is enabled, the unit will attempt to
register a second extension with the SIP server. Any calls
made to this extension will play a ringtone.
Nightringer Settings
SIP Server
Type the SIP server represented as either a numeric IP
address in dotted decimal notation.
Remote SIP Port
Type the Remote SIP Port number (default 5060)
(8 character limit).
Local SIP Port
Type the Local SIP Port number (default 5060)
(8 character limit).
Note: This value cannot be the same as the Local SIP Port*
found on the SIP Configuration Page.
User ID
Type the User ID (up to 64 alphanumeric characters).
Authenticate ID
Type the Authenticate ID (up to 64 alphanumeric
characters).
Authenticate Password
Type the Authenticate Password (up to 64 alphanumeric
characters).
Re-registration Interval (in seconds)
Type the SIP Registration lease time in minutes (default is
60 minutes) (8 character limit). Re-registration Interval (in
seconds)*
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Click on the Reboot button to reboot the system.
3. After changing the parameters, click on the Save button.
Operations Guide
930472J
CyberData Corporation
Installing the VoIP V3 Outdoor Intercom 35
Intercom Setup
2.4.8 Configure the Sensor Configuration Parameters
The door sensor (pins 5 and 6) on the header can be used to monitor a door's open or closed state.
There is an option on the Sensor Configuration page to trigger on an open or short condition on
these pins. The door sensor alarm will be activated when the Door Open Timeout parameter has
been met.
The intrusion sensor is an optical sensor installed on the Intercom board and will be activated when
the Intercom is removed from the case.
For each sensor there are four actions the Intercom can take:
•
Flash the LED until the sensor is deactivated (roughly 10 times/second)
•
Activate the relay until the sensor is deactivated
•
Loop an audio file out of the Intercom speaker until the sensor is deactivated
•
Call a preset extension and play a pre-recorded audio file (once)
Note
Operations Guide
Calling a preset extension can be set up as a point-to-point call, but currently can't send
delayed DTMF tones.
930472J
CyberData Corporation
Installing the VoIP V3 Outdoor Intercom 36
Intercom Setup
1. Click Sensor Config to open the Sensor Configuration page (Figure 2-17).
Figure 2-17. Sensor Configuration Page
Operations Guide
930472J
CyberData Corporation
Installing the VoIP V3 Outdoor Intercom 37
Intercom Setup
2. On the Sensor Configuration page, enter values for the parameters indicated in Table 2-13.
Table 2-13. Sensor Configuration Parameters
Web Page Item
Description
Door Sensor Settings
Door Sensor Normally Closed
Select the inactive state of the door sensors.
Door Open Timeout (in seconds)
Select the number of seconds that you want to pass before the
door sensor is activated.
Flash Button LED
Check this box to flash the LED until the sensor is deactivated
(roughly 10 times/second).
Activate Relay
Check this box to activate the relay until the sensor is deactivated.
Play Audio Locally
Check this box to loop an audio file out of the Intercom speaker
until the sensor is deactivated.
Make call to extension
Check this box to call a preset extension (once).
Play recorded audio
Check this box to play a pre-recorded audio file (once).
Dial Out Extension
Enter the desired dial-out extension number.
Dial Out ID
Type the desired Extension ID (64 character limit).
Use this button to test the door sensor.
Intrusion Sensor Settings
Flash Button LED*
Check this box to flash the LED until the sensor is deactivated
(roughly 10 times/second).
Activate Relay
Check this box to activate the relay until the sensor is deactivated.
Play Audio Locally
Check this box to loop an audio file out of the Intercom speaker
until the sensor is deactivated.
Make call to extension
Check this box to call a preset extension (once).
Play recorded audio
Check this box to play a pre-recorded audio file (once).
Dial Out Extension
Enter the desired dial-out extension number.
Dial Out ID
Type the desired Extension ID (64 character limit).
Use this button to test the Intrusion sensor.
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Click on the Reboot button to reboot the system.
3. After changing the parameters, click Save Settings.
Operations Guide
930472J
CyberData Corporation
Installing the VoIP V3 Outdoor Intercom 38
Intercom Setup
2.4.9 Configure the Multicast Parameters
Multicast groups use multicasting to create public address paging zones. Multicasting is based on
the concept of a group. Multicast addresses specify an arbitrary group of IP hosts that have joined
the group and want to receive traffic sent to the group. Group members send IGMP messages to
their local multicast routers, allowing the group traffic traversal from the source.
The Multicast Configuration page allows the Intercom to join up to 10 paging zones for receiving
ulaw/alaw encoded RTP audio streams. A paging zone can consist of one or many CyberData
multicast group-enabled products. There is no limit to how many devices can be in a given paging
zone. Each multicast group is defined by a multicast address and port number. Each multicast group
is assigned a priority, allowing simultaneously arriving pages to be serviced based on importance.
Multicast groups are compatible with IGMP through version three. The Intercom supports
simultaneous SIP and Multicast.
1. Click on the Multicast Configuration button to open the Multicast Configuration page. See
Figure 2-18.
Figure 2-18. Multicast Configuration Page
Operations Guide
930472J
CyberData Corporation
Installing the VoIP V3 Outdoor Intercom 39
Intercom Setup
2. On the Multicast Configuration page, enter values for the parameters indicated in Table 2-14.
Table 2-14. Multicast Configuration Parameters
Web Page Item
Description
Enable Multicast Operation
Enables or disables multicast operation.
Device Settings
Priority
Indicates the priority for the multicast group. Priority 9 is the
highest (emergency streams). 0 is the lowest (background
music). SIP calls are considered priority 4.5. See Section
2.4.9.1, "Assigning Priority" for more details.
Address
Enter the multicast IP Address for this multicast group (15
character limit).
Port (range can be from 2000 to 65535)
Enter the port number for this multicast group (5 character
limit).
Note: The multicast ports have to be even values. The
webpage will enforce this restriction.
Multicast Group Name
Assign a descriptive name for this multicast group (25
character limit).
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Click on the Reboot button to reboot the system.
3. After changing the parameters, click on the Save button.
2.4.9.1 Assigning Priority
When playing multicast streams, audio on different streams will preempt each other according to
their priority in the list. An audio stream with a higher priority will interrupt a stream with a lower
priority.
If both SIP and Multicast is enabled, SIP audio streams are considered priority 4.5. SIP audio will
interrupt multicast streams with priority 0 through 4 and will be interrupted by multicast streams with
priority 5 through 9.
During priority 9 multicast streams the volume level is set to maximum.
Note
Ringtones and
Nightringtones
Operations Guide
SIP calls, multicast streams, ring tones, ringback tones, and nightring tones are all
prioritized.
Ringtones all play at the same priority level. This means that it is possible to have a nightring tone
and a normal ringtone playing at the same time.
930472J
CyberData Corporation
Installing the VoIP V3 Outdoor Intercom 40
Intercom Setup
2.4.10 Configure the Audio Configuration Parameters
The Audio Configuration page is used to add custom audio to the board. User uploaded audio will
take precedence over the audio files shipped with the Intercom.
1. Click Audio Config to open the Audio Configuration page (Figure 2-19).
Figure 2-19. Audio Configuration Page
Operations Guide
930472J
CyberData Corporation
Installing the VoIP V3 Outdoor Intercom 41
Intercom Setup
Figure 2-20. Audio Configuration Page (continued)
2. On the Audio Configuration page, enter values for the parameters indicated in Table 2-15.
Operations Guide
930472J
CyberData Corporation
Installing the VoIP V3 Outdoor Intercom 42
Intercom Setup
Table 2-15. Audio Configuration Parameters
Web Page Item
Description
Audio Files
0-9
The name of the audio configuration option is the same as the spoken audio that
plays on the board (24 character limit).
'0' corresponds to the spoken word “zero.”
'1' corresponds to the spoken word “one.”
'2' corresponds to the spoken word “two.”
'3' corresponds to the spoken word “three.”
'4' corresponds to the spoken word “four.”
'5' corresponds to the spoken word “five.”
'6' corresponds to the spoken word “six.”
'7' corresponds to the spoken word “seven.”
'8' corresponds to the spoken word “eight.”
'9' corresponds to the spoken word “nine.”
Dot
Corresponds to the spoken word “dot.” (24 character limit)
Audiotest
Corresponds to the message “This is the CyberData IP speaker test message...”
(24 character limit)
Page tone
Corresponds to a simple tone used for beep on initialization and beep on page (24
character limit).
Your IP Address is
Corresponds to the message “Your IP address is...” (24 character limit).
Rebooting
Corresponds to the spoken word “Rebooting” (24 character limit).
Restoring default
Corresponds to the message “Restoring default” (24 character limit).
Ringback tone
This is the ringback tone that plays when calling a remote extension 
(24 character limit).
Ring tone
This is the tone that plays when set to ring when receiving a call 
(24 character limit).
Intrusion Sensor Triggered Corresponds to the message “Intrusion Sensor Triggered” (24 character limit).
Door Ajar
Corresponds to the message “Door Ajar” (24 character limit).
Night Ring
Specifies the ringtone for nightring. By default this parameter uses the same audio file
that is selected for the Ring Tone parameter.
The Browse button will allow you to navigate to and select an audio file.
The Play button will play that audio file.
The Delete button will delete any user uploaded audio and restore the stock audio
file.
The Save button will download a new user audio file to the board once you've
selected the file by using the Browse button. The Save button will delete any preexisting user-uploaded audio files.
Operations Guide
930472J
CyberData Corporation
Installing the VoIP V3 Outdoor Intercom 43
Intercom Setup
2.4.10.1 User-created Audio Files
User created audio files should be saved in the following format:
RIFF (little-endian) data, WAVE audio, Microsoft PCM, 16 bit, mono 8000 Hz
You can use the free utility Audacity to convert audio files into this format. See Figure 2-21 through
Figure 2-23.
Figure 2-21. Audacity 1
Figure 2-22. Audacity 2
Operations Guide
930472J
CyberData Corporation
Installing the VoIP V3 Outdoor Intercom 44
Intercom Setup
When you export an audio file with Audacity, save the output as:
•
WAV (Microsoft) signed 16 bit PCM.
Figure 2-23. WAV (Microsoft) signed 16 bit PCM
WAV (Microsoft) signed 16 bit PCM
Operations Guide
930472J
CyberData Corporation
Installing the VoIP V3 Outdoor Intercom 45
Intercom Setup
2.4.11 Configure the Event Parameters
Click the Event Config button to open the Event Configuration page (Figure 2-24). The Event
Configuration page specifies a remote server that can be used to receive HTTP POST events
when actions take place on the board.
Figure 2-24. Event Configuration Page
Table 2-16 shows the web page items on the Event Configuration page.
Operations Guide
930472J
CyberData Corporation
Installing the VoIP V3 Outdoor Intercom 46
Intercom Setup
Table 2-16. Event Configuration
Web Page Item
Description
Enable Event Generation
When selected, Event Generation is enabled.
Remote Event Server
Remote Event Server IP
Type the Remote Event Server IP address. 
(64 character limit)
Remote Event Server Port
Type the Remote Event Server port number.
(8 character limit)
Remote Event Server URL
Type the Remote Event Server URL.
(127 character limit)
Events
Enable Button Events
When selected, Button Events are enabled.
Enable Call Active Events
When selected, Call Active Events are enabled.
Enable Call Terminated Events
When selected, Call Terminated Events are enabled.
Enable Relay Activated Events
When selected, Relay Activated Events are enabled.
Enable Relay Deactivated
Events
When selected, Relay Deactivated Events are enabled.
Enable Ring Events
When selected, Ring Events are enabled.
Enable Night Ring Events
When selected, there is a notification when the unit receives a
night ring.
Enable Multicast Start Events
When selected, Multicast Start Events are enabled.
Enable Multicast Stop Events
When selected, Multicast Stop Events are enabled.
Enable Power On Events
When selected, Power On Events are enabled.
Enable Security Events
When selected, Security Events are enabled.
Enable 60 Second Heartbeat
Events
When selected, 60 Second Heartbeat Events are enabled.
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Click on the Test Event button to test an event.
Click on the Reboot button to reboot the system.
Operations Guide
930472J
CyberData Corporation
Installing the VoIP V3 Outdoor Intercom 47
Intercom Setup
2.4.11.1 Example Packets for Events
The server and port are used to point to the listening server and the 'Remote Event Server URL' is
the destination URL (typically the script running on the remote server that's used to parse and
process the POST events).
Note
The XML is URL-encoded before transmission so the following examples are not completely
accurate.
Here are example packets for every event:
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 197
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData VoIP Device' MAC='0020f70015b6'>
<event>POWERON</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 199
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData VoIP Device' MAC='0020f70015b6'>
<event>HEARTBEAT</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 196
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData VoIP Device' MAC='0020f70015b6'>
<event>BUTTON</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 201
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData VoIP Device' MAC='0020f70015b6'>
<event>CALL_ACTIVE</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
Operations Guide
930472J
CyberData Corporation
Installing the VoIP V3 Outdoor Intercom 48
Intercom Setup
User-Agent: CyberData/1.0.0
Content-Length: 205
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData VoIP Device' MAC='0020f70015b6'>
<event>CALL_TERMINATED</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 197
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData VoIP Device' MAC='0020f70015b6'>
<event>RINGING</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 234
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData VoIP Device' MAC='0020f70015b6'>
<event>MULTICAST_START</event>
<index>8</index>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 233
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData VoIP Device' MAC='0020f70015b6'>
<event>MULTICAST_STOP</event>
<index>8</index>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 234
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData VoIP Device' MAC='0020f70015b6'>
<event>RELAY_ACTIVATED</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
Operations Guide
930472J
CyberData Corporation
Installing the VoIP V3 Outdoor Intercom 49
Intercom Setup
User-Agent: CyberData/1.0.0
Content-Length: 234
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData VoIP Device' MAC='0020f70015b6'>
<event>RELAY_DEACTIVATED</event>
</cyberdata>
POST xmlparse_engine HTTP/1.1
Host: 10.0.3.79
User-Agent: CyberData/1.0.0
Content-Length: 234
Content-Type: application/x-www-form-urlencoded
<?xml version="1.0" encoding="ISO-8859-1"?>
<cyberdata NAME='CyberData VoIP Device' MAC='0020f70015b6'>
<event>NIGHTRINGING</event>
</cyberdata>
Operations Guide
930472J
CyberData Corporation
Installing the VoIP V3 Outdoor Intercom 50
Intercom Setup
2.4.12 Configure the Autoprovisioning Parameters
1. Click the Autoprovisioning button to open the Autoprovisioning Configuration page. 
See Figure 2-25.
Figure 2-25. Autoprovisioning Configuration Page
Operations Guide
930472J
CyberData Corporation
Installing the VoIP V3 Outdoor Intercom 51
Intercom Setup
2. On the Autoprovisioning Configuration page, you may enter values for the parameters
indicated in Table 2-17.
Table 2-17. Autoprovisioning Configuration Parameters
Web Page Item
Description
Autoprovisioning
Enable Autoprovisioning
See Section 2.4.12.1, "Autoprovisioning".
Get Autoprovisioning from DHCP
See Section 2.4.12.1, "Autoprovisioning".
Autoprovisioning Server (IP Address) See Section 2.4.12.1, "Autoprovisioning" (15 character limit).
Autoprovisioning Autoupdate 
(in minutes)
Type the desired time (in minutes) that you want the
Autoprovisioning feature to update (6 character limit).
Press the Get Autoprovisioning Template button to get an
autoprovisioning file for this board.
Click the Save button to save your configuration settings.
Note: You need to reboot for changes to take effect.
Click on the Reboot button to reboot the system.
3. After changing the parameters, click the Save button.
Operations Guide
930472J
CyberData Corporation
Installing the VoIP V3 Outdoor Intercom 52
Intercom Setup
2.4.12.1 Autoprovisioning
Enable
Autoprovisioning
Option
With autoprovisioning enabled, the board will get its configuration from a remote TFTP server on
startup or periodically on a scheduled delay. Autoprovisioned values will override values stored in
on-board memory and will be visible on the web page. The board gets its autoprovisioning
information from an XML-formatted file hosted from a TFTP server. CyberData will provide a
template for this XML file and the user can modify it for their own use.
To use autoprovisioning, create a copy of the autoprovisioning template with the desired settings and
name this file with the mac address of the device to configure (for example: 0020f7350058.config).
Put this file into your TFTP server directory and manually set the TFTP server address on the board.
It is not necessary to set every option found in the autoprovisioning template. As long as the XML is
valid, the file can contain any subset. Options not autoprovisioned will default to the values stored in
the on board memory. For example if you only wanted to modify the device name, the following
would be a valid autoprovisioning file:
<?xml version="1.0" encoding="utf-8" ?>
<specific>
<MiscSettings>
<DeviceName>auto Intercom</DeviceName>
</MiscSettings>
</specific>
Networking
The board will only apply networking settings or firmware upgrades after a reboot.
Get
Autoprovisioning
from DHCP
When this option is checked, the device will automatically fetch its autoprovisioning server address
from the DHCP server. The device will use the address specified in OPTION 150 (TFTP-servername) or OPTION 66. If both options are set, the device will use OPTION 150.
Refer to the documentation of your DHCP server for setting up OPTION 150.
Operations Guide
930472J
CyberData Corporation
Installing the VoIP V3 Outdoor Intercom 53
Intercom Setup
To set up a Linux DHCPD server to serve autoprovisioning information (in this case using both
option 66 and 150), here's an example dhcpd.conf:
# dhcpd.conf
#
# Configuration file for ISC dhcpd (see 'man dhcpd.conf')
#
ddns-update-style ad-hoc;
option option-150 code 150 = ip-address;
subnet 10.0.0.0 netmask 255.0.0.0 {
max-lease-time 120;
default-lease-time 120;
option routers
option subnet-mask
10.0.0.1;
255.0.0.0;
option domain-name
option domain-name-servers
"voiplab";
10.0.0.1;
option time-offset
-8;
option tftp-server-name
"10.0.0.254";
option option-150
10.0.0.254;
# Pacific Standard Time
range 10.10.0.1 10.10.2.1;}
Autoprovisioning Instead of using DHCP to provide the autoprovisioning tftp server address, you can specify an
Server (IP Address) address manually.
Autoprovisioning
Autoupdate
If Autoprovisioning is enabled and the Autoprovisioning Autoupdate value is something other
than 0 minutes, a service is started on startup that will wait the configured number of minutes and
then try to re-download its autoprovisioning file. It will compare its previously autoprovisioned file
with this new file and if there are differences, it will reboot the board.
Autoprovisioned An Autoprovisioned firmware upgrade only happens after a reboot, will take roughly three minutes,
Firmware Upgrades and the web page will be unresponsive during this time.
The 'FirmwareVersion' value in the xml file must match the version stored in the 'FirmwareFile'.
<FirmwareVersion>v6.3.0</FirmwareVersion>
<FirmwareFile>630-intercom-uImage</FirmwareFile>
If these values are mismatched, the board can get stuck in a loop where it goes through the following
sequence of actions:
1. The board downloads and writes a new firmware file.
2. After the next reboot, the board recognizes that the firmware version does not match.
3. The board downloads and writes the firmware file again.
CyberData has timed a firmware upgrade at 140 seconds. Therefore, if you suspect the board is
stuck in a loop, either remove or comment out the FirmwareVersion line in the XML file and let the
board boot as it normally does.
Operations Guide
930472J
CyberData Corporation
Installing the VoIP V3 Outdoor Intercom 54
Intercom Setup
Autoprovisioned
Audio Files
Audio files are stored in non-volatile memory and an autoprovisioned audio file will only have to be
downloaded once for each device. Loading many audio files to the device from the web page could
cause it to appear unresponsive. If this happens, wait until the transfer is complete and then refresh
the page.
The device uses the file name to determine when to download a new audio file. This means that if
you used autoprovisioning to upload a file and then changed the contents of this file at the TFTP
server, the device will not recognize that the file has changed (because the file name is the same).
Since audio files are stored in non-volatile memory, if autoprovisioning is disabled after they have
been loaded to the board, the audio file settings will not change. You can force a change to the audio
files on the board by clicking the Delete button on the Audio Configuration page which will restore
the default audio file. You can also change the autoprovisioning file with the word default set as the
file name.
Operations Guide
930472J
CyberData Corporation
Installing the VoIP V3 Outdoor Intercom 55
Intercom Setup
2.5 Upgrade the Firmware and Reboot the Intercom
Caution
Equipment Hazard: V3 devices like the VoIP V3 Outdoor Intercom cannot use
firmware 6.x.x or earlier, and older V1 and V2 devices cannot use firmware
7.x.x or later.
GENERAL ALERT
Note
A new firmware signature prevents users from loading firmware intended for one device to a
different device. See Table 2-18.
Table 2-18. Firmware
Firmware File Name
Description
intercom_v7.1.6_with_signature
Intercom v7.1.6 with signature can be used to downgrade the
firmware from version 8.0.0 or higher.
intercom_v8.0.0_with_signature
Intercom v8.0.0 with signature can be used to downgrade the
firmware to version 8.0.0 from a higher version.
2.5.1 Uploading the Firmware
To upload the firmware from your computer:
1. Retrieve the latest Intercom firmware file from the VoIP V3 Outdoor Intercom Downloads page
at:
http://www.cyberdata.net/products/voip/digitalanalog/intercomv3/downloads.html
2. Unzip the firmware version file. This file may contain the following:
•
Firmware file
•
Release notes
3. Log in to the Intercom home page as instructed in Section 2.4.3, "Log in to the Configuration
Home Page".
4. Click the Update Firmware button to open the Upgrade Firmware page. See Figure 2-26.
Operations Guide
930472J
CyberData Corporation
Installing the VoIP V3 Outdoor Intercom 56
Intercom Setup
Figure 2-26. Upgrade Firmware Page
5. Select Browse, and then navigate to the location of the Intercom firmware file.
6. Click Submit.
Note
Do not reboot the board after pressing the Submit button.
Note
This starts the upgrade process. Once the Intercom has uploaded the file, the Uploading
Firmware countdown page appears, indicating that the firmware is being written to flash.
The Intercom will automatically reboot when the upload is complete. When the countdown
finishes, the Upgrade Firmware page will refresh. The uploaded firmware filename should
be displayed in the system configuration (indicating successful upload and reboot).
Table 2-19 shows the web page items on the Upgrade Firmware page.
Table 2-19. Firmware Upgrade Parameters
Web Page Item
Description
File Upload
Firmware Version
Shows the current firmware version.
Use the Browse button to navigate to the location of the
Intercom firmware file that you want to upload.
Click on the Submit button to automatically upload the selected
firmware and reboot the system.
Operations Guide
930472J
CyberData Corporation
Installing the VoIP V3 Outdoor Intercom 57
Intercom Setup
2.5.2 Reboot the Intercom
To reboot a Intercom, log in to the web page as instructed in Section 2.4.3, "Log in to the
Configuration Home Page".
1. Click Reboot (Figure 2-27). A normal restart will occur.
Figure 2-27. Reboot System Section
Reboot
Operations Guide
930472J
CyberData Corporation
Installing the VoIP V3 Outdoor Intercom 58
Intercom Setup
2.6 Command Interface
Some functions on the device can be activated using simple POST commands to the web interface.
The examples in Table 2-20 use the free unix utility, wget commands. However, any program that
can send HTTP POST commands to the device should work.
2.6.1 Command Interface Post Commands
Note
These commands require an authenticated session (a valid username and password to
work).
Table 2-20. Command Interface Post Commands
Device Action
HTTP Post Commanda
Trigger relay (for configured delay)
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/command.cgi" --post-data
"test_relay=yes"
Place call to extension (example: extension 130)
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/command.cgi" --post-data
"call=130"
Place point-to-point callb 
(example: IP phone address = 10.0.3.72)
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/command.cgi" --post-data
"call=10.0.3.72"
Terminate active call
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/command.cgi" --post-data
"terminate=yes"
Force reboot
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/command.cgi" --post-data
"reboot=yes"
Test Audio button
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/command.cgi" --post-data
"test_audio=yes"
Announce IP address
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/command.cgi" --post-data
"speak_ip_address=yes"
Play the "0" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_0=yes"
Play the "1" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_1=yes"
Play the "2" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_2=yes"
Play the "3" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_3=yes"
Operations Guide
930472J
CyberData Corporation
Installing the VoIP V3 Outdoor Intercom 59
Intercom Setup
Table 2-20. Command Interface Post Commands (continued)
Device Action
HTTP Post Commanda
Play the "4" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_4=yes"
Play the "5" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_5=yes"
Play the "6" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_6=yes"
Play the "7" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_7=yes"
Play the "8" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_8=yes"
Play the "9" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_9=yes"
Play the "Dot" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_d=yes"
Play the "Audio Test" audio file (from Audio Config)
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_audiotest=yes"
Play the "Page Tone" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_pagetone=yes"
Play the "Your IP Address Is" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_youripaddressis=yes"
Play the "Rebooting" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_rebooting=yes"
Play the "Restoring Default" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_restoringdefault=yes"
Play the "Ringback tone" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_ringback=yes"
Play the "Ring tone" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_ringtone=yes"
Play the "Intrusion Sensor Triggered" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_intrusionsensortriggered=yes"
Play the "Door Ajar" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_doorajar=yes"
Operations Guide
930472J
CyberData Corporation
Installing the VoIP V3 Outdoor Intercom 60
Intercom Setup
Table 2-20. Command Interface Post Commands (continued)
Device Action
HTTP Post Commanda
Play the "Night Ring" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"play_nightring=yes"
Delete the "0" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"delete_0=yes"
Delete the "1" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"delete_1=yes"
Delete the "2" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"delete_2=yes"
Delete the "3" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"delete_3=yes"
Delete the "4" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"delete_4=yes"
Delete the "5" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"delete_5=yes"
Delete the "6" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"delete_6=yes"
Delete the "7" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"delete_7=yes"
Delete the "8" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"delete_8=yes"
Delete the "9" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"delete_9=yes"
Delete the "Audio Test" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"delete_audiotest=yes"
Delete the "Page Tone" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"delete_pagetone=yes"
Delete the "Your IP Address Is" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"delete_youripaddressis=yes"
Delete the "Rebooting" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"delete_rebooting=yes"
Delete the "Restoring Default" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"delete_restoringdefault=yes"
Operations Guide
930472J
CyberData Corporation
Installing the VoIP V3 Outdoor Intercom 61
Intercom Setup
Table 2-20. Command Interface Post Commands (continued)
Device Action
HTTP Post Commanda
Delete the "Ringback tone" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"delete_ringback=yes"
Delete the "Ring tone" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"delete_ringtone=yes"
Delete the "Intrusion Sensor Triggered" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"delete_intrusionsensortriggered=yes"
Delete the "Door Ajar" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"delete_doorajar=yes"
Delete the "Night Ring" audio file
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/audioconfig.cgi" --post-data
"delete_nightring=yes"
Trigger the Door Sensor Test (Sensor Config page)
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/sensorconfig.cgi" --post-data
"doortest=yes"
Trigger the Intrusion Sensor Test (Sensor Config page)
wget --user admin --password admin --auth-no-challenge --quiet O /dev/null "http://10.0.3.71/cgi-bin/sensorconfig.cgi" --post-data
"intrusiontest=yes"
a.Type and enter all of each http POST command on one line.
b. Must be in point-to-point mode see Section 2.4.6.2, "Point-to-Point Configuration"
Operations Guide
930472J
CyberData Corporation
62
Appendix A: Mounting the Intercom
A.1 Mounting Components
Before you mount the Intercom, make sure that you have received all the parts for each Intercom.
Refer to the following tables.
Table A-1. Mounting Components (Part of the Accessory Kit)
Quantity
Part Name
1
T-15H Torx Key
4
Security Torx Screw
Illustration
Table A-2. Optional Accessories (for gooseneck mounting)
Quantity
Part Name
4
Carriage bolt nuts
4
Carriage bolts
4
Carriage bolt washers
Illustration
Table A-3. Optional Accessories
Operations Guide
Quantity
Part Name
1
Spacer for half-inch set conduit
connector
1
531085B hole plug assembly
930472J
Illustration
CyberData Corporation
Mounting the Intercom 63
Dimensions
A.2 Dimensions
Figure A-1. Unit Dimensions—Front and Side View
Figure A-2. Unit Dimensions—Rear View with Mounting Hole Locations
Dimensions are in Inches [Millimeter]
0.869 [22.07]
ø0.280 [ø7.11]
(4 Places)
ø0.854 [ø21.69]
3.380
[85.85]
1.690
[42.93]
1.690
[42.93]
3.380 [85.85]
Operations Guide
930472J
0.869 [22.07]
CyberData Corporation
Mounting the Intercom 64
Dimensions
Figure A-3. Shroud Dimensions—Front and Side View with Mounting Hole Locations
3.434 [87.23]
0.874 [22.20]
ø0.854 [ø21.69]
3.380 [85.85]
5.202 [132.13]
ø0.280 [ø7.11]
(4 PLACES)
1.690 [42.93]
5.276 [134.00]
1.690 [42.93]
3.380 [85.85]
0.948 [24.07]
Dimensions are in Inches [Millimeter]
Figure A-4. Unit Dimensions—Unit without the Gang Box
Effective Range for
Intrusion Sensor to Function
Affix Reflective Surface Above
Intrusion Sensor
from 3 mm (Minimum)
to 14 mm (Maximum)
0.118 [3.0]
0.551 [14.0]
Intrustion
Sensor
4.580 [116.33]
5.118 [130.00]
0.156" [4.0] THROUGH HOLE
82 DEGREES COUNTERSUNK (4 PLACES)
1.986 [50.45]
Operations Guide
4.000 [101.60]
5.118 [130.00]
DIMENSIONS ARE IN INCHES [MILLIMETER]
930472J
CyberData Corporation
65
JP1 JP5
J4
JP10
< Intrusion Sensor >
J6
3.700 [93.98]
J5
4.200 [106.68]
JP7
J7
J3
J10
J2
4.200 [106.68]
DIMENSIONS ARE IN INCHES [MILLIMETER]
930472J
SW1
J1
0.063 [1.60]
TOP SIDE
0.063 [1.60]
BOTTOM SIDE
ø0.138 [ø3.51]
Fits #6-32 Machine Screw
(4 Places)
CyberData Corporation
1.169 [29.70]
Effective Range for
Intrusion Sensor to Function
from 3 mm to 14 mm
0.551 [14.00]
0.118 [3.00]
2.300 [58.42]
0.591 [15.00]
0.516 [13.10]
Operations Guide
Dimensions
Figure A-5. PCB Dimensions and Intrusion Sensor Range
Mounting the Intercom 66
Overview of Installation Types
A.3 Overview of Installation Types
An overview of the installation types and the required components are provided in Table A-4.
Table A-4. Overview of Installation Types
Installation Type
What You Need
Outdoor, on surface
011186 Intercom only
Outdoor, on surface with shroud (increased resistance)
011186 Intercom
011188 Weather Shroud (sold separately)
Operations Guide
930472J
CyberData Corporation
Mounting the Intercom 67
Network Cable Entry Restrictions
A.4 Network Cable Entry Restrictions
A.4.1 Side Conduit Network Cable Entry Restrictions
See Figure A-6 for the side conduit cable entry restrictions.
Figure A-6. Side Conduit Network Cable Entry Restrictions
Hole Plug
Assembly
Spacer
1/2" Conduit
Connector
(Not Provided)
1/2" Conduit
(Not Provided)
Network
Cable In
Operations Guide
930472J
CyberData Corporation
Mounting the Intercom 68
Network Cable Entry Restrictions
A.4.2 Rear Conduit Network Cable Entry Restrictions (without Shroud)
See Figure A-7 for the rear conduit cable entry restrictions (without Shroud).
Figure A-7. Rear Conduit Network Cable Entry Restrictions—Without Shroud
Spacer
1/2" Conduit
Connector
(Not Provided)
1/2" Conduit
(Not Provided)
Approx. 3/8"
[9.5mm] without
Optional Shroud On
Network
Cable In
A.4.3 Rear Conduit Network Cable Entry Restrictions (with Shroud)
See Figure A-8 for the rear conduit cable entry restrictions (with shroud).
Figure A-8. Rear Conduit Network Cable Entry Restrictions—With Shroud
Spacer
1/2" Conduit
Connector
(Not Provided)
1/2" Conduit
(Not Provided)
Approx. 29/64'
[11.5mm] with
Optional Shroud On
Operations Guide
930472J
Network
Cable In
CyberData Corporation
Mounting the Intercom 69
Ground Cable Installation
A.5 Ground Cable Installation
Figure A-9 illustrates how to connect a ground cable to the VoIP V3 Outdoor Intercom.
Figure A-9. Ground Cable Installation
Nut
Ground Wire
(Not Provided)
Ground Lug
Note: To mount the intercom, use methods
compliant with local electrical codes.
Operations Guide
930472J
CyberData Corporation
Mounting the Intercom 70
Service Loop Cable Routing
A.6 Service Loop Cable Routing
Figure A-10 and Figure A-11 illustrate a service loop cable routing option for the VoIP V3 Outdoor
Intercom.
Figure A-10. Ground Cable Service Loop Routing
Ground Lug
Route cable(s) inside of the
Route Cable(s) inside Gang Box to
Gang
Box Creates
to create
the
service loop.
Service
Loop
Ground Cable
(not provided)
Nut (to Ground Lug
inside of the Gang Box
Figure A-11. Network Cable Service Loop Routing
Route
of theBox to
Routecable(s)
Cable(s) inside
inside Gang
Service
Loop loop.
Gang Box Creates
to create
the service
Network Cable
(not provided)
Operations Guide
930472J
CyberData Corporation
Mounting the Intercom 71
Securing the Intercom
A.7 Securing the Intercom
Figure A-12 illustrates how to secure the VoIP V3 Outdoor Intercom with Torx screws.
Figure A-12. Securing the Intercom
Note: To mount the intercom, use methods
compliant with local electrical codes.
2-Gang Box
Torx Key
Torx Screws
Faceplate &
PCB Assembly
Caution
GENERAL ALERT
Operations Guide
Equipment Hazard: Do not use an electric or power screwdriver to fasten
the face plate and PCB assembly to the gang box. To prevent over-torque
damage to the gasket, do not apply more than 10 inch-pounds force. Overtorquing will cause the gasket to tear, risk moisture intrusion, and
effectively void the manufacturer's warranty.
930472J
CyberData Corporation
Mounting the Intercom 72
Additional Mounting Options
A.8 Additional Mounting Options
A.8.1 Conduit Mounting Option (Not Provided)
Figure A-13 illustrates a side and rear conduit mounting option for the VoIP V3 Outdoor Intercom.
Figure A-13. Optional Conduit Mounting
Note: To mount the intercom, use methods
compliant with local electrical codes.
Rotate the 2- Gang Box in the
Rotate the 2-Gang Box in
desired direction for the conduit
the
desired direction for the Conduit
Operations Guide
930472J
CyberData Corporation
Mounting the Intercom 73
Additional Mounting Options
A.8.2 Concrete Wall Mounting Option (Not Provided)
Figure A-14 illustrates a concrete wall mounting option for the VoIP V3 Outdoor Intercom.
Figure A-14. Optional Concrete Wall Mounting
Note: To mount the intercom, use methods
compliant with local electrical codes.
Hole Plug
Assembly
(Hole Plug,
Washer & Nut)
1/4" Concrete
Wall Anchors
(Not Provided)
Spacer
(One Provided)
1/4" Carriage
Screw
(Not Provided)
1/2” Set Screw
Connector
(Not Provided)
1/2" Conduit
(Not Provided)
Network
Cable In
Operations Guide
930472J
CyberData Corporation
Mounting the Intercom 74
Additional Mounting Options
A.8.3 Goose Neck Mounting Option (Not Provided)
Figure A-15 illustrates a gooseneck mounting option for the VoIP V3 Outdoor Intercom.
Figure A-15. Optional Goose Neck Mounting
Note: To mount the intercom, use methods
compliant with local electrical codes.
Remove the hole plug assembly
from the 2-Gang Box before
fastening it to the Shroud and/or
Gooseneck
Operations Guide
930472J
CyberData Corporation
Mounting the Intercom 75
Additional Mounting Options
A.8.4 Ground Cable Installation for Goose Neck Mounting Option
Figure A-16 illustrates the correct ground cable installation for the gooseneck mounting option.
Figure A-16. Ground Cable Installation for Goose Neck Mounting
Note: To mount the intercom, use methods
compliant with local electrical codes.
Operations Guide
930472J
CyberData Corporation
76
Appendix B: Setting up a TFTP Server
B.1 Set up a TFTP Server
Autoprovisioning requires a TFTP server for hosting the configuration file.
B.1.1 In a LINUX Environment
To set up a TFTP server on LINUX:
1. Create a directory dedicated to the TFTP server, and move the files to be uploaded to that
directory.
2. Run the following command where /tftpboot/ is the path to the directory you created in
Step 1: the directory that contains the files to be uploaded. For example:
in.tftpd -l -s /tftpboot/your_directory_name
B.1.2 In a Windows Environment
You can find several options online for setting up a Windows TFTP server. This example explains
how to use the Solarwinds freeware TFTP server, which you can download from the following
website address:
http://www.cyberdata.net/support/voip/solarwinds.html
To set up a TFTP server on Windows:
1. Install and start the software.
2. Select File/Configure/Security tab/Transmit Only.
3. Make a note of the default directory name, and then move the firmware files to be uploaded to
that directory.
Operations Guide
930472J
CyberData Corporation
77
Appendix C: Troubleshooting/Technical
Support
C.1 Frequently Asked Questions (FAQ)
A list of frequently asked questions (FAQs) are available on the VoIP V3 Outdoor Intercom product
page at:
http://www.cyberdata.net/products/voip/digitalanalog/intercomv3/faqs.html
Select the support page for your product to see a list of frequently asked questions for the
CyberData product:
C.2 Documentation
The documentation for this product is released in an English language version only. 
You can download PDF copies of CyberData product documentation from the
VoIP V3 Outdoor Intercom product page at:
http://www.cyberdata.net/products/voip/digitalanalog/intercomv3/docs.html
Operations Guide
930472J
CyberData Corporation
Troubleshooting/Technical Support 78
Contact Information
C.3 Contact Information
Contact
CyberData Corporation
3 Justin Court
Monterey, CA 93940 USA
www.CyberData.net
Phone: 800-CYBERDATA (800-292-3732)
Fax: 831-373-4193
Sales
Sales 831-373-2601 Extension 334
Technical 
Support
The fastest way to get technical support for your VoIP product is to submit a VoIP Technical
Support form at the following website:
http://support.cyberdata.net/
The Support Form initiates a ticket which CyberData uses for tracking customer requests. Most
importantly, the Support Form tells us which PBX system and software version that you are
using, the make and model of the switch, and other important information. This information is
essential for troubleshooting. Please also include as much detail as possible in the Comments
section of the Support Form.
Phone: (831) 373-2601, Ext. 333
Email: support@cyberdata.net
Returned
Materials
Authorization
To return the product, contact the Returned Materials Authorization (RMA) department:
Phone: 831-373-2601, Extension 136
Email: RMA@CyberData.net
When returning a product to CyberData, an approved CyberData RMA number must be printed
on the outside of the original shipping package. Also, RMA numbers require an active VoIP
Technical Support ticket number. A product will not be accepted for return without an approved
RMA number. Send the product, in its original package, to the following address:
CyberData Corporation
3 Justin Court 
Monterey, CA 93940 
Attention: RMA "your RMA number"
RMA Status Form If you need to inquire about the repair status of your product(s), please use the CyberData RMA
Status form at the following web address:
http://support.cyberdata.net/
C.4 Warranty and RMA Information
The most recent warranty and RMA information is available at the following website address:
http://support.cyberdata.net/
Operations Guide
930472J
CyberData Corporation
79
Index
the web access password 23
Cisco SRST 29
command interface 58
commands 58
concrete wall mounting option (not provided) 73
conduit mounting option (not provided) 72
configurable parameters 24, 27, 29
configuration
audio 40
default IP settings 18
door sensor 35
intrusion sensor 35
network 26
SIP 28
using Web interface 18
configuration home page 20
configuration page
configurable parameters 24, 27
contact information 78
contact information for CyberData 78
Current Network Settings 27
current network settings 27
CyberData contact information 78
Numerics
16 AWG gauge wire 9
A
AC voltages 3
AC voltages, intercom enclosure is not rated 10
act light 14
activate relay (door sensor) 37
activate relay (intrusion sensor) 37
address, configuration login 20
alternative power input 6
announcing a device’s IP address 15
audio configuration 40
night ring tone parameter 42
audio configuration page 40
audio encodings 5
audio files, user-created 43
autoprovisioning 52
autoprovisioned audio files 54
autoprovisioned firmware upgrades 53
autoprovisioning autoupdate 53
autoprovisioning enabled option 52
autoprovisioning from DHCP 52
autoprovisioning server (IP address) 53
get autoprovisioning template button 51
networking 52
setting up a TFTP server 76
autoprovisioning configuration 50, 51
D
default
gateway 18
intercom settings 79
IP address 18
subnet mask 18
username and password 18
web login username and password 20
default gateway 18, 27
default intercom settings 16
default IP settings 18
default login address 20
device configuration 23
device configuration parameters 51
the device configuration page 50
device configuration page 23
device configuration parameters 24
device configuration password
changing for web configuration access 23
DHCP Client 5
DHCP IP addressing 27
dial out extension (door sensor) 37
dial out extension (intrusion sensor) 37
dial out extension strings 30
dial-out extension strings 32
B
backup SIP server 1 29
backup SIP server 2 29
backup SIP servers, SIP server
backups 29
baud rate
verifying 14
C
call button 17
LED 17
call button LED 17
changing
Operations Guide
930472J
CyberData Corporation
Index 80
dimensions 6, 63
pcb dimensions and intrusion sensor range 65
shroud dimensions and mounting hole locations 64
unit dimensions and intrusion sensor range without
the gang box 64
unit dimensions—front and side view 63
unit dimensions—rear view and mounting hole
locations 63
discovery utility program 20
DNS server 27
door sensor 35, 37, 42
activate relay 37
dial out extension 37
door open timeout 37
door sensor normally closed 37
flash button LED 37
play audio locally 37
DTFM
play tone during DTMF activation 24
DTMF tones 30, 32
DTMF tones (using rfc2833) 30
ground cable installation 69
ground cable installation for goose neck mounting
option 75
H
home page 20
http POST command 58
http web-based configuration 5
I
electric screwdriver 71
enable night ring events 46
ethernet I/F 6
event configuration
enable night ring events 46
expiration time for SIP server lease 29, 34
export configuration button 22
export settings 22
identifying your product 1
import configuration button 22
import settings 22
import/export settings 22
installation, typical intercom system 2
intercom configuration
default IP settings 18
intercom configuration page
configurable parameters 29
intrusion sensor 35, 37
activate relay 37
dial out extension 37
flash button LED 37
play audio locally 37
IP address 18, 27
IP addressing 27
default
IP addressing setting 18
F
J
factory default settings 16
how to set 16
fastening, gang box 71
firmware
where to get the latest firmware 55
firmware signature 55
flash button LED (door sensor) 37
flash button LED (intrusion sensor) 37
J3 terminal block, 16 AWG gauge wire 9
E
L
lease, SIP server expiration time 29, 34
lengthy pages 39
link light 14
Linux, setting up a TFTP server on 76
local SIP port 29
log in address 20
G
gang box, fastening 71
gasket, avoid over-torque damage 71
get autoprovisioning template button 51
goose neck mounting option (not provided) 74
green link light 14
Operations Guide
M
MGROUP
930472J
CyberData Corporation
Index 81
MGROUP Name 39
mounting 62
additional mounting options 72
concrete wall mounting option (not provided) 73
conduit mounting option (not provided) 72
goose neck mounting option (not provided) 74
ground cable installation 69
ground cable installation for goose neck mounting
option 75
network cable entry restrictions 67
optional accessories 62
overview of installation types 62, 66
rear conduit network cable entry restrictions (with
shroud) 68
rear conduit network cable entry restrictions (without
shroud) 68
securing the intercom 71
service loop cable routing 70
side conduit network cable entry restrictions 67
mounting components 62
multicast configuration 38
Multicast IP Address 39
N
navigation (web page) 19
navigation table 19
network cable entry restrictions 67
network configuration of intercom 26
Network Setup 26
nightring tones 39
Nightringer 9, 33
Nightringer in peer to peer mode (cannot be used) 33
nightringer settings 34
Nightringer, SIP registration required 33
O
on-board relay 6, 10
on-board relay wiring diagram 11
operating temperature 6
overview of installation types 66
P
packet time 5
pages (lengthy) 39
part number 6
password
for SIP server login 29
login 20
Operations Guide
930472J
restoring the default 18
payload types 6
pcb dimensions and intrusion sensor range 65
play audio locally (door sensor) 37
play audio locally (intrusion sensor) 37
play tone during DTMF activation 24
point-to-point configuration 31
port
local SIP 29
remote SIP 29
POST command 58
power input 6
alternative 6
power screwdriver 71
priority
assigning 39
product
configuring 18
parts list 7
product features 4
product overview
product features 4
product specifications 6
supported protocols 5
supported SIP servers 5
typical system installation 2
product specifications 6
protocol 6
protocols supported 5
R
rear conduit network cable entry restrictions (with
shroud) 68
rear conduit network cable entry restrictions (without
shroud) 68
reboot 56, 57
remote SIP port 29
reset test function management button 15
resetting the IP address to the default 62, 77
restoring factory default settings 16, 79
restoring the factory default settings 16
ringtones 39
lengthy pages 39
RJ-45 13
RMA returned materials authorization 78
RMA status 78
RTFM button 15
RTFM jumper 15, 16
RTP/AVP 5
CyberData Corporation
Index 82
S
sales 78
securing the intercom 71
sensor setup page 36
sensor setup parameters 35
sensors 37
server address, SIP 29
service 78
service loop cable routing 70
setting up an intercom 9
settings, default 16
shroud dimensions and mounting hole locations 64
side conduit network cable entry restrictions 67
SIP
enable SIP operation 29
local SIP port 29
user ID 29
SIP (session initiation protocol) 5
SIP configuration 28
SIP Server 29
SIP configuration parameters
outbound proxy 29
registration and expiration, SIP server lease 29, 34
user ID, SIP 29
SIP registration 29
SIP remote SIP port 29
SIP server 29
password for login 29
SIP servers supported 5
user ID for login 29
SIP settings 30
speaker output 6
SRST 29
static IP addressing 27
subnet mask 18, 27
supported protocols 5
upgrading to firmware 6.x.x from 5.x.x 71
user ID
for SIP server login 29
username
changing for web configuration access 23
default for web configuration access 20
restoring the default 18
V
verifying
baud rate 14
network connectivity 14
W
warranty policy at CyberData 78
web access password 18
web access username 18
web configuration log in address 20
web page
navigation 19
web page navigation 19
web-based intercom configuration 18
wget, free unix utility 58
Windows, setting up a TFTP server on 76
Y
yellow act light 14
T
tech support 78
technical support, contact information 78
terminal block, 16 AWG gauge wire 9
TFTP server 5, 76
U
unit dimensions and intrusion sensor range without the
gang box 64
unit dimensions—front and side view 63
unit dimensions—rear view and mounting hole
locations 63
Operations Guide
930472J
CyberData Corporation
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising