AcuRite Professional Weather Center 01301CCDI

AcuRite Professional Weather Center 01301CCDI
Instruction Manual
Professional Weather Center
model 01301CCDI / 393242
CONTENTS
Unpacking Instructions...................2
Package Contents..........................2
Product Registration.......................2
Features & Benefits: 3-in-1.............3
Features: Display Unit....................4
Setup...........................................6
3-in-1 Sensor Setup.......................6
Display Unit Setup.........................7
Set Language, Time, Date & Units...8
Placement Guidelines..................9
3-in-1 Sensor Installation...........10
Using the Weather Center..........11
Troubleshooting.........................13
Care & Maintenance.................15
Calibration...............................15
Specifications............................16
FCC Information........................16
Customer Support.....................17
Warranty..................................17
Questions? Contact Customer Support at
(877) 221-1252 or visit www.AcuRite.com.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
Congratulations on your new AcuRite product. To ensure the best
possible product performance, please read this manual in its entirety
and retain it for future reference.
Unpacking Instructions
Remove the protective film that is applied to the LCD screen prior to using this
product. Locate the tab and peel off to remove.
Package Contents
1. Display unit with tabletop stand
2. 3-in-1 sensor
3. Sensor mounting bracket
4. Mounting hardware
5. Power adapter
6. Instruction Manual
IMPORTANT
PRODUCT MUST BE REGISTERED
TO RECEIVE WARRANTY SERVICE
PRODUCT REGISTRATION
Register online
to receive 1 year
warranty protection
www.AcuRite.com
►Register a Product
2
Features & Benefits
4
1
6
2
5
3
3-in-1 SENSOR
5. M
ounting Hardware
Includes anchors and screws.
Qty Diameter
Length
4
#4 1”
1
#6
3/8”
1. T emperature & Humidity Sensors
(internal)
2. Release Lever for Battery Access
3. Mounting Point
6. M
ounting Bracket
4. Wind Speed Anemometer
7. A
-B-C Switch (not shown)
ID code that must match display’s
A-B-C switch to ensure units
synchronize.
3
Features & Benefits
1
2
3 4 5 6 7
Display Unit
8
28
27
26
25
24
23
22
9
10
11
12
13
14
15
21
20
19
18
17
16
29
34
30
31
32
33
35
4
DISPLAY UNIT
19. – Button
1. Current Outdoor Temperature
Arrow icon indicates direction
20.
For setup preferences.
Button
Press to change the Weather Select
(#23) category being displayed.
temperature is trending.
2.Sensor Low Battery Indicator
21. Barometric Pressure
3.Average Wind Speed
Average of all speeds over last
30 minutes or calibrated time interval.
rrow icon indicates direction
A
pressure is trending.
22.Learning Mode Icon
Disappears after weather forecast
self-calibration is complete.
4.Backlight Button
5.Current Wind Speed
23.Weather Select
Displays heat index, dew point or wind 6.Wind Gust Icon
7. Peak Wind Speed
8.Current Indoor Temperature
24.Language
Highest speed from last 30 minutes or
calibrated time interval.
For setup preferences.
Arrow icon indicates direction
temperature is trending.
25.AUTO DIM Indicator
9.Display Low Battery Indicator
26.Current Outdoor Humidity
10. Current Indoor Humidity
Arrow icon indicates direction
temperature is trending.
Arrow icon indicates direction
humidity is trending.
27. Low Wind Speed
11.Clock
Lowest speed from past 30 minutes or
calibrated time interval.
12.Date
13.
chill, daily, monthly, all time high & low records indoor/outdoor temperatures
and humidity and high for wind speed.
28.Outdoor Sensor Signal Strength
and LIVE Icons
indicates historical data is
being displayed. LIVE icon is shown
while exiting
function.
BACK
OF DISPLAY UNIT
29.Integrated Hang Hole
14. 12 to 24 Hour Weather Forecast
Self-Calibrating Forecasting pulls data
from the outdoor sensor to generate
your personal forecast.
For easy wall mounting
30. Plug-in for Power Adapter
31. Battery Compartment
15. Multi-Variable History Chart
32.A-B-C Switch
16.
33.CLEAR RECORD/RESET Button
ID code that must match sensor’s A-B-C
switch to ensure units synchronize.
Displays the past 12 hours of data for
pressure, temperature and humidity.
Button
Press to clear record currently being
viewed. Press and HOLD for full reset
to factory defaults.
For displaying historical data.
17. + Button
18.
For setup preferences.
34. Battery Compartment Cover
Button
35.Power adapter
For setup preferences.
5
SETUP
3-IN-1 Sensor Setup
1 Set the A-B-C Switch
1. Press the release lever and pull
off the lower housing of the
sensor.
The A-B-C switch is located inside
the battery compartment. It can be
set to A, B or C. However, you must
select the same letter choices for
both the sensor and the display unit
in order for the units to synchronize.
2. Remove the battery compartment
cover. Take note of the A-B-C
switch setting inside the battery
compartment.
2 Install or Replace Batteries
3. Insert 4 x AA batteries into the
battery compartment, as shown.
Follow the polarity (+/-) diagram
in the battery compartment.
AcuRite recommends high quality
alkaline or lithium batteries for the
best product performance. Heavy
duty or rechargeable batteries are
not recommended.
4. Replace the battery cover and
lower housing of the sensor.
The 3-in-1 sensor requires lithium
batteries in low temperature
conditions. Cold temperatures can
cause alkaline batteries to function
improperly. Use lithium batteries in
the 3-in-1 sensor for temperatures
below -4ºF / -20ºC.
ABC
1
A-B-C Switch
set to match
display unit
2
6
Display Unit Setup
1 Set the A-B-C Switch
2 Install or Replace Batteries
L ocate the A-B-C switch inside the
battery compartment. Set the A-B-C
switch to A, B or C. You must select
the same letter choices for both the
display unit and the sensor in order
for the units to synchronize.
1. Remove the battery
compartment cover.
2. Insert 6 x AA alkaline batteries
into the battery compartment,
as shown. Follow the polarity
(+/-) diagram in the battery
compartment.
3. Replace the battery cover.
3 Plug Power Adapter into
Electric Outlet
3
Plug in
Power
Adapter
1
2
Install Batteries
6 AA Batteries
(optional)
A-B-C Switch
set to match sensor
ABC
IMPORTANT: Batteries are a backup power source
to preserve records in the event of a power outage.
Power adapter is recommended as the primary power
source to enjoy the full functionality of this product.
PLEASE DISPOSE OF OLD OR DEFECTIVE BATTERIES IN AN ENVIRONMENTALLY SAFE
WAY AND IN ACCORDANCE WITH YOUR LOCAL LAWS AND REGULATIONS.
BATTERY SAFETY: Clean the battery contacts and also those of the device prior to battery installation. Remove batteries from equipment which is not to be
used for an extended period of time. Follow the polarity (+/-) diagram in the battery compartment. Promptly remove dead batteries from the device. Dispose of used
batteries properly. Only batteries of the same or equivalent type as recommended are to be used. DO NOT incinerate used batteries. DO NOT dispose of batteries in fire,
as batteries may explode or leak. DO NOT mix old and new batteries or types of batteries (alkaline/standard). DO NOT use rechargeable batteries. DO NOT recharge
non-rechargeable batteries. DO NOT short-circuit the supply terminals.
7
Set the Time, Date & Units
Press the “ ” button, located on the front of the display unit, to enter SET
MODE. Once in set mode, the preference you are currently setting will blink on
the display.
To adjust the currently selected (flashing) item, press and release the “+“ or
“--“ buttons (press and HOLD to fast adjust).
To save your adjustments, press and release the “ ” button again to adjust
the next preference. The preference set order is as follows:
LANGUAGE (English or French)
CLOCK HOUR
CLOCK MINUTE
CALENDAR MONTH
CALENDAR DATE
CALENDAR YEAR
TEMPERATURE UNITS (ºF or ºC)
WIND UNITS (MPH or KM/H)
PRESSURE UNITS (inHg or hPa)
You will automatically exit SET MODE if no buttons are pressed for 10 seconds.
Enter setup mode at any time by pressing the “ ” button.
Display Backlight Settings
This weather station’s color display features three different lighting settings:
High (100%) brightness, Medium (60%) brightness and Low (30%) brightness
Using battery power alone, the backlight is available momentarily for 10
” button.
seconds by pressing the “
When display is powered with the power adapter, backlight remains on
at 100% brightness. Press “
” button once to dim to 60% brightness;
press again to dim to 30%, press a 3rd time to enter “AUTO DIM” mode.
AUTO DIM appears above time and date.
AUTO DIM MODE: Automatically adjusts display brightness based on time of day & year.
MARCH 11- NOVEMBER 4
6:00 a.m. - 9:00 p.m. = 100% brightness
9:01 p.m. - 5:59 a.m.= 30% brightness
NOVEMBER 5 - MARCH 10
7:30 a.m. - 7:00 p.m.= 100% brightness
7:01 p.m. - 7:29 a.m. = 30% brightness
8
Placement for Maximum Accuracy
AcuRite sensors are sensitive to surrounding environmental conditions. Proper
placement of both the display unit and the sensor are critical to the accuracy and
performance of this product.
Display Unit Placement
Place the display unit in a dry area free of dirt and dust. To ensure
accurate temperature measurement, place out of direct sunlight and
away from heat sources or vents. Display unit stands upright for
tabletop use or is wall-mountable.
3-in-1 Sensor Placement
The 3-in-1 sensor is designed to remain outdoors all year long.
Choose an open location with no obstructions above or around the
sensor for the most accurate measurements.
Important Placement Guidelines
Display unit and sensor must be within 330 feet (100 m) of each other.
MAXIMIZE WIRELESS RANGE
P lace units away from large metallic items, thick walls, metal surfaces, or other
objects that may limit wireless communication.
PREVENT WIRELESS INTERFERENCE
P lace both units at least 3 feet (.9 m) away from electronic devices (TV, computer,
microwave, radio, etc.).
LOCATE AWAY FROM HEAT SOURCES
Position sensor away from heaters, air conditioners, chimneys, exhaust vents, asphalt
and concrete (surfaces that radiate heat).
LOCATE AWAY FROM HUMIDITY SOURCES
Avoid installing the sensor near pools, spas, or other bodies of water. Water sources
may impact humidity accuracy.
LOCATE AWAY FROM SPRINKLER HEADS
DO NOT install the sensor where it will be sprayed by a sprinkler system. This may
force water inside the sensor.
LOCATE AWAY FROM WIND OBSTRUCTIONS
DO NOT mount the sensor with obstructions around it.
Consider a location that is a wide open area, with few
structures around to ensure accurate wind speed measurement.
Visit us online to view installation photos and
video, or learn more about AcuRite technology:
www.AcuRite.com/3in1
9
View Video
3-in-1 Sensor Installation Guidelines
INSTALLATION HEIGHT Mount the sensor at least 5 feet (1.5 meters) off the ground
(higher is better for wind measurement) in an open area. Secure to fence post, 2”x4”
wood, 3/4” pole, etc. (not included)
LEVEL INSTALLATION Use a bubble level (not included) to ensure level installation for
accurate wind measurement.
Top or Side Mount
Top Mount
1. Insert the mounting base into the
hole on the bottom of the sensor.
Side Mount
2. Use one of the screws included
in the hardware bag to fasten
the lower sensor housing to the
mounting base.
3. Fasten mounting base to a post or
railing using 2 screws.
Pole Mount
1. Insert pole (we recommend 3/4” schedule
40 PVC / 25.8 mm O.D., not included)
or similar item all the way into the hole on
the bottom of the sensor. Note: Mounting
base is not used.
2. Use one of the screws included in the
hardware bag to fasten the lower sensor
housing securely to the pole.
Pole Mount
Do not install during
electrical storms.
Do not place pole
or sensor near
electrical lines or
electrical equipment.
The 3-in-1 sensor is now ready to use.
Clear Data Collected During Installation
When installation is complete, clear erroneous data from the display unit by pressing
the “CLEAR RECORD/RESET” button for each category, on the back of the display
inside the battery compartment.
Basic Setup is Complete
The 3-in-1 sensor will now synchronize with the display unit. It may take a few
minutes for synchronization to complete. If both or one of the units appear to be
functioning improperly, please refer to the troubleshooting section.
10
OPERATION
Using The Weather Center
Learning Mode
Self-Calibrating Forecasting use a unique algorithm to analyze changes in
pressure over a time period (called Learning Mode) to determine your altitude. After
14 days, the Learning Mode icon disappears from the display screen. At this point,
the self-calibrated pressure is tuned in to your location and the unit is ready for superior weather prediction.
Weather Forecast
AcuRite’s patented Self-Calibrating Forecasting provides your personal forecast of
weather conditions for the next 12 to 24 hours by collecting data from the sensor in
your backyard. It generates a forecast with pinpoint accuracy - personalized for your
exact location.
STORMY
& WINDY
SNOW
LIKELY
(flashing=stormy)
SNOW / RAIN
MIX LIKELY
RAIN
LIKELY
MOSTLY
CLOUDY
(flashing rain/snow)
View the complete list of icons at www.AcuRite.com/acurite-icons
Multi-Variable History Chart
The multi-variable history chart lets you monitor the change in conditions over the
past 12 hour time period (-12, -6, -3, -2, -1, 0). The chart automatically toggles
between barometric pressure, outdoor temperature and outdoor humidity readings.
Wind Speed
The Wind Speed area of the display features the CURRENT speed, as well as the
LOW, AVERAGE and PEAK wind speeds. PEAK, AVERAGE and LOW wind speeds
are based on the past 30 minute time frame by default. The time frame can be
adjusted during the calibration process (page 15).
Barometric Pressure
Subtle variations in barometric pressure greatly impact the weather. This weather
center displays the current pressure with an arrow icon to indicate the direction the
pressure is trending (FALLING, STEADY, or RISING). The multi-variable history chart
lets you monitor the change in pressure over time.
11
Weather Select
Features weather data groups shown at right. To
change “Weather Select” category, press the “ “
button on the front of the display. When outdoor/
indoor temperature or humidity is chosen, the display
cycles through the category’s records in this order:
24 Hour Change (data change since 24 hours ago)
Today’s HIGH
Today’s LOW
Month’s HIGH
Month’s LOW
All Time HIGH
All Time LOW
When Wind Speed is chosen, the display cycles through the following records:
Today’s HIGH
Month’s HIGH
All Time HIGH
To clear a record, view one of the values listed above and press the “CLEAR
RECORD/RESET” button, located on the back of the unit in the battery compartment.
Dashes display to confirm the record has been cleared.
REPLAY Historical Data
This weather station stores historical data that can be viewed in Replay Mode. Data
is recorded for the past 48 hours in 30 minute intervals (on the hour and half hour).
Historical data is shown with a time and date stamp.
Press the “ ” button to enter Replay Mode. The “
shown on the display below the time.
“ icon and options will be
REPLAY MODE OPTIONS:
• Press the “ ” (
) button to view 48-hour historical data. First, data is shown
that was recorded 48 hours ago, and then the display cycles through the historical
data in 30 minute intervals up to the current time. To exit Replay Mode and view
live data, press the “ ” button
• Press the “-” ( ) button to view historical data in 30 minute intervals previous to
the current “LIVE” data.
• While viewing historical data, press the “+” (
by a 30 minute interval.
) button to advance the data shown
You will automatically exit Replay Mode if no buttons are pressed for 10 seconds.
To manually exit Replay Mode at any time, press the “ ” button. The display may
show or flash the “LIVE” icon to confirm you are exiting Replay Mode and returning
to the current (“LIVE”) data view.
12
Troubleshooting
Problem
No outdoor sensor
reception
no bars
Possible Solution
• Relocate the display unit and/or the 3-in-1 sensor.
The units must be within 330 ft (100 m) of each other.
• Make sure both units are placed at least 3 feet (.9 m)
away from electronics that may interfere with the wireless
communication (such as TVs, microwaves, computers, etc).
• Use standard alkaline batteries (or lithium batteries in
sensor when temperature is below -4ºF/-20ºC). Do not use
heavy duty or rechargeable batteries. NOTE: It may take
up to 20 minutes for display unit and sensor to synchronize
after batteries are replaced.
• Synchronize the units:
1. Bring both the sensor and display unit indoors and
remove at least one battery from each.
2. Make sure the A-B-C switch on both units match.
3. Reinstall the battery in the outdoor sensor.
4. Reinstall battery into the display unit.
5. Let the units sit within a couple feet of each other for
about 20 minutes to gain a strong connection.
Outdoor
temperature
is flashing or
showing dashes
Flashing of the outdoor temperature may be an indication of
wireless interference:
• Make sure the A-B-C switch in the battery compartments of
both the display unit and sensor are switched to the same
letter. You may choose A, B or C; but both units must match
to sync up. Sometimes changing to a different channel can
help.
Inaccurate forecast
• Weather Forecast icon predicts conditions for the next 12
to 24 hours, not current conditions.
• Has Learning Mode icon disappeared from the display
unit? Learning Mode must complete before forecast and
pressure will be accurate.
• Allow unit to run continuously for 33 days. Battery removal
or resetting the display unit will restart Learning Mode.
After 14 days, forecast should be fairly accurate, however
Learning Mode calibrates for a total of 33 days.
13
Troubleshooting
Problem
Possible Solution
Inaccurate
temperature or
humidity
• Make sure both the display unit and 3-in-1 sensor are
placed away from any heat sources or vents (see page 9).
• Make sure both units are positioned away from moisture
sources (see page 9).
• Make sure 3-in-1 sensor is mounted at least 5 ft off of
the ground.
• Calibrate indoor and outdoor temperature and humidity
(see page 15).
Inaccurate wind
readings
• What is wind reading being compared to? Pro weather
stations are typically mounted at 30 ft high or more. Make
sure to compare data using a sensor positioned at the
same mounting height.
• Check location of the sensor. Ensure it’s mounted a
minimum of 5 ft in the air with no obstructions around it
(within several feet).
•Ensure wind cups are spinning freely. If they hesitate or stop
try lubricating with graphite powder or spray lubricant.
Display screen
not working
• Check that the batteries are installed correctly.
Batteries may need to be replaced.
• Reset the display by pressing and HOLDING the
“CLEAR RECORD/RESET” button, located on the
back of the display unit in the battery compartment.
Date and time will need to be entered after a reset.
If your AcuRite product does not operate properly after trying
the troubleshooting steps, visit www.AcuRite.com or call
(877) 221-1252 for assistance.
14
Care & Maintenance
Display Unit Care
Clean with a soft, damp cloth. Do not use caustic cleaners or abrasives. Keep away from dust,
dirt and moisture. Clean ventilation ports regularly with a gentle puff of air.
3-in-1 Sensor Care
Clean the Sensor
Clean with a soft, damp cloth. Do not use caustic cleaners or abrasives.
Insect Prevention
Insects may cause obstructions and interrupt data by nesting in or on the 3-in-1 sensor. To limit
this problem, spray sensor housing with a household insect repellent. Note: Insect repellent
should not be sprayed on the internal components or into the sensor. Consult insect repellent
instructions prior to use.
Snow & Freezing Weather
The 3-in-1 sensor will not be damaged by freezing conditions.
Clean the Wind Anemometer
Remove foreign matter from the outside of the sensor for free movement of the wind anemometer. If needed, use a small amount of spray lubricant, clear silicone or graphite powder on the
anemometer for improved movement. Note: Spray lubricant, clear silicone or graphite powder
should not be sprayed on the internal components or into the sensor.
Calibration
The indoor / outdoor temperature and humidity readings, wind speed interval, and barometric
pressure can be calibrated on the display unit to improve accuracy. Calibration can improve
accuracy when sensor placement or environmental factors impact the data accuracy.
1. To access calibration mode, press AND HOLD the “-“, “
for at least 5 seconds.
” and “+“ buttons simultaneously
2. To adjust the currently selected (flashing) item, press and release the “-“ or “+“ buttons to
calibrate the data value higher or lower from the actual reading.
3. To save your adjustments, press and release the “ ” button to adjust the next preference.
The “ ” icon will remain illuminated next to calibrated values.
The preference set order is as follows:
OUTDOOR TEMPERATURE
OUTDOOR HUMIDITY
INDOOR TEMPERATURE
INDOOR HUMIDITY
WIND SPEED INTERVAL (30, 60, 90, 120, 150 or 180 minutes)
BAROMETRIC PRESSURE (must be set to MANUAL mode to calibrate)*
*To change from AUTO to MANUAL pressure mode and vice versa, press AND HOLD
the “ ” button for at least 10 seconds. The display indicates the current pressure mode
selected,“AUTO” or “MANUAL”. After 10 seconds of inactivity, the display will save the
adjustments and exit calibration mode. Note: Calibration preferences will be erased if the
display is reset or if batteries are removed and the power adapter is unplugged.
15
Specifications
TEMPERATURE RANGE
Outdoor: -40ºF to 158ºF; -40ºC to 70ºC
Indoor: 32ºF to 122ºF; 0ºC to 50ºC
HUMIDITY RANGE
Outdoor: 1% to 99%
Indoor: 1% to 99%
WIND SPEED
0 to 99 mph; 0 to 159 kph
WIRELESS RANGE
330 ft / 100 m depending on home construction materials
OPERATING FREQUENCY
433 mhz
POWER
Display: 5
V, 100mA power adapter
6 x AA alkaline batteries
Sensor: 4 x AA alkaline or lithium batteries
Wind Speed: 18 second updates
DATA REPORTING
Outdoor temperature & humidity: 18 second updates
Indoor temperature & humidity: 60 second updates
FCC Information
This device complies with part 15 of FCC rules. Operation is subject to the following two conditions:
1- This device may NOT cause harmful interference, and
2- This device must accept any interference received, including interference that may cause undesired operation.
WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications
could void the user authority to operate the equipment.
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two confitions:
(1) This device may not cause interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation of the device.
16
Customer Support
AcuRite customer support is committed to providing you with best-in-class
service. For assistance, please have the model number of this product
available and contact us in any of the following ways:
(877) 221-1252
info@chaney-inst.com
24/7 support at www.AcuRite.com
► Installation
Videos
► Register
your Product
► Instruction
Manuals
► Support
User Forum
► Replacement
Parts
► Submit
IMPORTANT
Feedback & Ideas
PRODUCT MUST BE REGISTERED
TO RECEIVE WARRANTY SERVICE
PRODUCT REGISTRATION
Register online
to receive 1 year
warranty protection
www.AcuRite.com
►Register a Product
Limited One Year Warranty
At AcuRite, we proudly uphold our commitment
to quality technology. Chaney Instrument Co.
warrants that all products it manufactures to be of
good material and workmanship, and to be free of
defects when properly installed and operated for a
period of one year from the date of purchase.
it manufactures which have received normal wear and tear,
been damaged (including by acts of nature), tampered, abused,
improperly installed, damaged in shipping, or repaired or altered
by others than authorized representatives of Chaney.
The above-described warranty is expressly in lieu of all other
warranties, express or implied, and all other warranties are
hereby expressly disclaimed, including without limitation the
implied warranty of merchantability and the implied warranty
of fitness for a particular purpose. Chaney expressly disclaims
all liability for special, consequential or incidental damages,
whether arising in tort or by contract from any breach of this
warranty. Some states do not allow the exclusion or limitation
of incidental or consequential damages, so the above limitation
or exclusion may not apply to you. Chaney further disclaims all
liability from personal injury relating to its products to the extent
permitted by law. By acceptance of any of Chaney’s products,
the purchaser assumes all liability for the consequences arising
from their use or misuse. No person, firm or corporation is
authorized to assume for Chaney any other liability in connection
with the sale of its products. Furthermore, no person, firm or
corporation is authorized to modify or waive the terms of this
paragraph, and the preceding paragraph, unless done in writing
and signed by a duly authorized agent of Chaney. This warranty
gives you specific legal rights, and you may also have other rights
which vary from state to state.
We recommend that you visit us at
www.AcuRite.com for the fastest way to register
your product. However, product registration does
not eliminate the need to retain your original proof
of purchase in order to obtain warranty benefits.
Chaney Instrument Co. warrants that all products it
manufactures to be of good material and workmanship, and to be
free of defects when properly installed and operated for a period
of one year from the date of purchase. Remedy for breach of
this warranty is limited to repair or replacement of the defective
item(s). Any product which, under normal use and service, is
proven to breach the warranty contained herein within ONE YEAR
from date of sale will, upon examination by Chaney, and at its
sole option, be repaired or replaced by Chaney. Transportation
costs and charges for returned goods shall be paid for by
the purchaser. Chaney hereby disclaims all responsibility for
such transportation costs and charges. This warranty will
not be breached, and Chaney will give no credit for products
For in-warranty claims:
Chaney Instrument Co. | 965 Wells St. | Lake Geneva, WI 53147
17
Weather
Stations
Temperature
& Humidity
Weather
Alert Radio
Kitchen
Thermometers
& Timers
Clocks
It’s more than accurate, it’s
AcuRite offers an extensive assortment of precision instruments,
designed to provide you with information you can depend on to
Plan your day with confidence™.
www.AcuRite.com
Printed in China
01301CCDI INST 061014
©Chaney Instrument Co. All rights reserved. AcuRite is a registered trademark of the
Chaney Instrument Co., Lake Geneva, WI 53147. All other trademarks and copyrights
are the property of their respective owners. AcuRite uses patented technology.
Visit www.AcuRite.com/patents for details.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising