Manual 12684243
PRODUCTION RELEASE & REVISION
REV DESCRIPT'N/BUYER
DWG No
A
PARTS No. BY
------------------- 50303702 J.Y.LIU
INITIAL
DATE
CHK
M.J.KWON 14-02-06
148+/-5)mm
Height Strip Covert Camera
NOTES
Please read this manual thoroughly before use, and keep it handy for future reference.
Design and specifications are subject to change without notice.
1.MODEL: HCE-N41KNF3SH(960H height-strip)
2.MATERIAL: 모조지100g/m2 WHITE
3.COLOR: BLACK
4.SIZE: 105(+/-5)mm x 148(+/-5)mm
5.LABEL: ------------6.ANY CHANGE OR ALTERNATION MUST BE
APPROVED BY HITRON DESIGN TEAM.
105(+/-5)mm
50303702
전자
장경석
UNLESS OTHERWISE SPECIFIED
ALL DIMENSIONS ARE IN MM.
- TOLERANCE
LABEL
+/- 3
MANUAL +/- 5
GUIDE
+/- 5
MATERIAL
COLOR
14-02-06
2
3
APPROVALS
ITEM
QTY
DESCRIPTION/MATERIAL
PARTS LIST
DATE
TITLE
J.H.JUNG 14-02-06
Instruction Manual
CHKED
M.J.KWON 14-02-06
DRAWN
J.Y.LIU 14-02-06
SIZE
REV.
A4
SCALE
DO NOT SCALE
A
Height Strip Covert Camera
Please read this manual thoroughly before use, and keep it handy for future reference.
Design and specifications are subject to change without notice.
FCC COMPLIANCE STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
FCC INFORMATION : This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense.
CAUTION : Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
CE COMPLIANCE STATEMENT
WARNING : This is a Class A poduct. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate measures.
2
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5.. Do not block any ventilat ion openings. Install in accord ance with the manufacturer`s
instructions.
6. Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
7. Only use attachments/accessories specified by the manufacturer.
8. Use only with the ca rt, stand, tripod, bracket, or table specified by
the manufacturer, or sold with the apparatus. When a cart is used,
use caution when moving the cart/ apparatus combination to avoid
injury from tip-over.
9.
CAUTION - THESE SERVICING IN STRUCTIONS ARE FOR USE BY
QUALIFIED SERVICE PERSONNEL ONLY. TO REDUCE THE RISK OF
ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING OTHER THAN
THAT CONTAINED IN THE OPERATING INSTRUCTIONS UNLESS YOU
ARE QUALIFIED TO DO SO.
10. Use satisfy clause 2.5 of IEC60950-1/UL 60950-1 or Certified/Listed Class 2
power source only.
11. Indoor use only.
EXPLANATION OF GRAPHICAL SYMBOLS
3
INTRODUCTION
Features:
High resolution and high performance 1/3" Color CCD
Excellent picture quality
700 lines of resolution(Color)
0.1 lux(Color), 0.04ux(B/W) @ F1.2 50IRE Sensitivity
Auto electronic shutter [1/60(1/50) ~ 1/100,000]
Auto white balance
AGC (Auto Gain Control)
Use Certified / Listed Class 2 power source only
2D DNR (Digital Noise Reduction)
Side Light Compensation
3.7mm Pin hole Lens
BNC (Video connection) 2-Pin terminal block (Power)
Operates in DC12~15V +/- 10%
IMPORTANT : The user of this camera is responsible for checking and
complying with local, state, and federal laws and statutes concerning the
recording and monitoring of audio signals.
4
77 3/4"
Step 1
Drill feed-thru hole for cable on mounting surface 77 3/4" above the finished floor.
5
Step 2
Feed wire through the 3/4" hole on the gimble mount.
6
Step 3
Center the gimbal mount to mounting surface and mark the mounting holes for the gimbal mount on
the surface.
Secure the gimbal mount to the surface using installer supplied self tappers for aluminum frame
structure.
If mounting on soft surface such as drywall be sure to use to use anchors.
7
Step 4
Completing the housing installation
Remove the five white head M4 screws that hold the face plate to the housing
and set the face plate aside.
Feed the wire coming through the gimbal mount through the 3/4" hole in the
back of the camera housing.
Attach the camera housing to the gimbal mount using the M6 Allen head screws
and washer previously removed.
Place the external tooth washer between the housing and the gimbal mount then
the split lock washer on the M6 screw and insert the screw into the housing
through the gimbal mount and external tooth lock wasker.
Install the bolt and washers assembly at the bottom and top of the gimbal mount
finger tight. (See Figure-1)
M6 Allen head screw
Split lock washer between gimbal mount and housing
External tooth lock washer under head of bolt
Figure-1
After connecting the video and power to their proper connections replace the
face plate that was removed in an earlier step using the five screws.
Adjust the position of the housing in the gimbal mount for the proper view and
then tighten the top and bottom Allen head screws using an Allen head wrench.
Verify that the housing is in the proper position and is secure.
8
Optional Camera Height Setting
1. The Height strip camera has the capability to be set in the housing at 5ft or
5.5ft above the floor.
The default setting of the camera is set to 5.5ft.
If the lower setting is desired the following housing change must be
completed.
* Remove housing from gimbal
* Note the position of the hole in the housing base for cable throughput
1
2
The cable hole is at the top of the mounting bracket
* Remove three Allen head screws along each side of the housing and
separate the front cover with the camera from the housing base.
Figure-2
Allen head screw
* From 1 to 2 to change the camera position. (See Figure-2)
* Replace the front cover with the camera to the housing base after
turning the cover 180o from original position.
Replace the three Allen head screws along each side of the housing
and continue the installation
2. Camera lens position can be adjusted up and down 5 degrees.
92 o
92 o
[ft]
5o
92 o
[cm]
Figure-3
3. Two height marker strips are provided, one marked in feet
and one marked in centimeters. Use the appropriate one.
(See Figure-3)
9
5
o
DIMENSIONS
inch
HEIGHT STRIP CAMERA
10
SPECIFICATIONS
NTSC
MODEL
Power
General
Power source
Power consumption
Image sensor
Number of pixels
Scanning system
Scanning frequency
Sync. system
Electronic shutter
Resolution
Min. illumination
Side Light Compensation
Digital Noise Reduction
Video output
S/N ratio
AGC
Day / Night
Connector
&
etc.
PAL
DC12~15V +/-10%
130mA (1.5 Watts)
1/3" Color CCD
976(H) x 494(V)
976(H) x 582(V)
2:1 interlace
15.734KHz(H) x 59.94Hz(V)
15.625KHz(H) x 50Hz(V)
Internal
1/60 ~ 1/100,000 sec.
1/50 ~ 1/100,000 sec.
700 TV lines (Color)
0.1 lux(COLOR), 0.04 lux(BW) @ F1.2, 50 IRE
Auto
2D DNR
1.0 Vp-p (75 ohm, composite)
More than 50dB (AGC off)
ON
Auto
Auto(ATW)
Terminal Block
BNC Connector
Fixed mount
F3.7mm Pin hole Fixed
o
-10 C ~ +50oC [14oF ~ 122oF ]
0 ~ 96% (non-condensing)
White Balance
Power input
Video output
Lens mount
Lens
Operating Temperature
Operating humidity
1.8"(W) x 34.4"(H) x 1.4"(D)
set : 1260g packing : 2035g
External Dimension
Weight
* Use the power consumption 2W over.
11
Height Strip Covert Camera
PRINTED IN KOREA
50303702A
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising