Vig450J BIOS Settings Information Windows 7

Vig450J BIOS Settings Information Windows 7
Viglen recommends Windows 8.
Windows 8/8.1 BIOS Setting
VIG450J (PMPFS450)
Vig450J system configured with Windows 8.1 will have following default BIOS settings. If you wish to
downgrade from Windows 8.1 to Windows 7 or other legacy operating system then BIOS must be
configured to Non-UEFI mode.
Windows 8/8.1 UEFI mode BIOS settings.
Secure Boot Control
[Enabled]
CSM Parameters
CSM Configuration
Launch CSM
Boot Option filter
Launch PXE OpROM policy
Launch Storage OpROM policy
Launch Video OpROM policy
[Enabled]
[UEFI Only]
[UEFI only]
[UEFI only]
[UEFI OpROM]
Other PCI device ROM priority [UEFI OpROM]
Windows 7 (Non UEFI Mode) BIOS settings.
Secure Boot Control
[Disabled]
CSM Parameters
CSM Configuration
Launch CSM
Boot Option filter
Launch PXE OpROM policy
Launch Storage OpROM policy
Launch Video OpROM policy
[Enabled]
[UEFI and Legacy]
[Legacy Only]
[Legacy Only]
[Legacy Only]
Other PCI device ROM priority [Legacy OpROM]
To enable downgrade to Windows 7 operating system, BIOS settings must be changed to boot into
Legacy BIOS mode (Non UEFI Mode).
Note
Please ensure the changes of the following settings are performed by personnel with some previous
experience/knowledge of altering BIOS settings.
Viglen Limited, VHQ, 7 Handley Page Way, Old Parkbury Lane, Colney Street, St. Albans, Hertfordshire AL2 2DQ
Tel: 01727 201 850 | Fax: 01727 201858 | Email: technical@viglen.co.uk| Web: www.viglen.co.uk
Viglen recommends Windows 8.
Figure 1- BIOS setup Screen
BIOS Settings for Windows 8/8.1 Operating System (UEFI Mode)
Accessing BIOS Setup
Press the <DEL> key to access BIOS setup during POST checks.
Enabling Windows 8/8.1 Features [UEFI Mode]
1. From the BIOS main menu select <Security>
2. Select <Secure Boot>
Figure 2 –Secure Boot option
Viglen Limited, VHQ, 7 Handley Page Way, Old Parkbury Lane, Colney Street, St. Albans, Hertfordshire AL2 2DQ
Tel: 01727 201 850 | Fax: 01727 201858 | Email: technical@viglen.co.uk| Web: www.viglen.co.uk
Viglen recommends Windows 8.
3. On the ‘Secure Boot Configuration’ menu Enable below settings:
Secure Boot Control
[Enabled]
Figure 3 – Secure Boot Configuration
4. From Secure Boot Mode Select [Custom]
Figure 4 – Secure Boot configuration
Viglen Limited, VHQ, 7 Handley Page Way, Old Parkbury Lane, Colney Street, St. Albans, Hertfordshire AL2 2DQ
Tel: 01727 201 850 | Fax: 01727 201858 | Email: technical@viglen.co.uk| Web: www.viglen.co.uk
Viglen recommends Windows 8.
5. Enable Factory Default Key Provisioning
Figure 5 – Secure Boot Default Key Provisioning
6. Select ‘Enrol All Factory Default Keys’ to install the default keys. Ensure all keys are set to
installed
Figure 6 - Secure Boot Default Key Provisioning
7. Press Escape to Exit the Secure Boot Default Key Provisioning screen.
8. Set the Secure mode to [Standard]
Viglen Limited, VHQ, 7 Handley Page Way, Old Parkbury Lane, Colney Street, St. Albans, Hertfordshire AL2 2DQ
Tel: 01727 201 850 | Fax: 01727 201858 | Email: technical@viglen.co.uk| Web: www.viglen.co.uk
Viglen recommends Windows 8.
Figure 7 – Final Secure Boot Configuration Settings
Note: When Secure Boot Control is set to [Enabled], CSM Parameters option will not be visible
under Boot screen. CSM parameters is available when Secure Boot Control is set to [Disabled]
Figure 8 – CSM parameters under Boot screen
Viglen Limited, VHQ, 7 Handley Page Way, Old Parkbury Lane, Colney Street, St. Albans, Hertfordshire AL2 2DQ
Tel: 01727 201 850 | Fax: 01727 201858 | Email: technical@viglen.co.uk| Web: www.viglen.co.uk
Viglen recommends Windows 8.
For Windows 8/8.1 configuration CSM Parameters are set to following:
CSM Parameters
CSM Configuration
Launch CSM
Boot Option filter
Launch PXE OpROM policy
Launch Storage OpROM policy
Launch Video OpROM policy
[Enabled]
[UEFI Only]
[UEFI only]
[UEFI only]
[UEFI OpROM]
Other PCI device ROM priority [UEFI OpROM]
Figure 9 – UEFI CSM Settings
For Windows 7 operating systems Secure Boot Control settings should be set to Disabled.
Viglen Limited, VHQ, 7 Handley Page Way, Old Parkbury Lane, Colney Street, St. Albans, Hertfordshire AL2 2DQ
Tel: 01727 201 850 | Fax: 01727 201858 | Email: technical@viglen.co.uk| Web: www.viglen.co.uk
Viglen recommends Windows 8.
Disabling Windows 8/8.1 Features [Non UEFI Mode]
Disabling Secure Boot
1. Select ‘Secure Boot’ from Security Screen.
Figure 10 – Default Key Provisioning [Disabled]
2. Select Secure Boot Control and select [Disabled]
Figure 11 – Disabling Secure Boot
Viglen Limited, VHQ, 7 Handley Page Way, Old Parkbury Lane, Colney Street, St. Albans, Hertfordshire AL2 2DQ
Tel: 01727 201 850 | Fax: 01727 201858 | Email: technical@viglen.co.uk| Web: www.viglen.co.uk
Viglen recommends Windows 8.
3. Press <ESC key> to exit the Security Menu and navigate to the Boot Menu.
4. Select <CSM parameters> and change the settings to following:
CSM Parameters
CSM Configuration
Launch CSM
Boot Option filter
Launch PXE OpROM policy
Launch Storage OpROM policy
Launch Video OpROM policy
[Enabled]
[UEFI and Legacy]
[Legacy Only]
[Legacy Only]
[Legacy Only]
Other PCI device ROM priority [Legacy OpROM]
Figure 12 -
5. Once all BIOS settings have been configured press <F4> key to Save and Exit the BIOS Setup.
Additional information:
For BIOS, Drivers and Documentation enquiries please contact Viglen Technical Support Department on
technical@viglen.co.uk.
Remember to include your PC serial number in all correspondence.
Viglen Limited, VHQ, 7 Handley Page Way, Old Parkbury Lane, Colney Street, St. Albans, Hertfordshire AL2 2DQ
Tel: 01727 201 850 | Fax: 01727 201858 | Email: technical@viglen.co.uk| Web: www.viglen.co.uk
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising