MK-DGV Vandal Resistant PanTilt Video Door Station Instructions

MK-DGV Vandal Resistant PanTilt Video Door Station Instructions
1005
Vandal Resistant Black & White Pan Tilt Video Door Station
- INSTALLATION INSTRUCTIONS FLUSH MOUNTING INSTRUCTIONS
1. Cut a hole in the wall that is 9-1/16" x 6-1/8". (Ensure
that mounting depth of at least 2-11/16" is available.)
2. Pass cable through knockout holes.
3. Secure back box in the wall so that the front of box is
flush with the outside edge of the wall.
4. Connect wires to the MK-DGV. (See wiring diagram)
5. Attach the MK-DGV to the mounting box using the
supplied screws and tamper proof tool.
MK-DGV
SURFACE MOUNTING INSTRUCTIONS (REQUIRES SBX-DGV, SOLD SEPARATELY)
1. The SBX-DGV is designed to mount to a 1 or 2 gang
box or ring or to any flat surface.
2. Pass cable through knockout holes.
3. Secure mounting box to wall.
4. Connect wires to the MK-DGV. (See wiring diagram)
5. Attach the MK-DGV to the mounting box using the
supplied screws and tamper proof tool.
SBX-DGV
MK-DGV
SAMPLE WIRING DIAGRAM
MK-2MCD
1A1
1A2
A1
A2
A1
A2
MK-DGV
w/SBX-DGV
MK-DBC
2A1
2A2
B1
B2
+
-
PS-1820UL
+
Pg. 1
WIRING PRECAUTIONS
1. Keep video wires at least 12" away from AC
100~240V power lines.
2. Use 2 conductor non-shielded wire with PE insulation.
(Aiphone 871802 wire.) Coax-cable cannot be used.
3. If there are unused wires in the cable, install a 120Ω
resistor between each pair of unused conductors.
4. Do no mix audio/video wires with those of another
video door station or device in the same cable.
MK-DGV
MK-2MCD
IMAGE VIEW AREA (approx.) when panned-and-tilted
•The image viewing area is a guideline and may vary according to environment.
•The peripheral part of the monitor may be slightly distorted.
•The image may have reflective light coming into the lens from the camera cover.
MOUNTING LOCATIONS & HEIGHT
Do not install the video door station in the following
locations:
- Places subject to temperature/humidity extremes.
- Places subject to dust, vapor, smoke, or chemicals.
- Places that are strongly backlit.
- Places where direct sunlight or strong light comes
into the camera lens.
OPERATION
Calling: Momentarily press CALL button on the door station.
After person at the monitor station replies, talk hands free while standing in front of the camera.
TECHNICAL PRECAUTIONS
Caulking seals: Do not apply any caulking seals around the video door station. Water drainage holes on the
bottom will help water or moisture to dissipate.
Cleaning:
Clean MK-DGV with a soft cloth dampened with neutral household cleanser. Never use any
harsh cleanser or cloth. Do not spray high-pressure water on the video door station.
Pg. 2
SPECIFICATIONS
Power Source:
Consumption:
Picture element:
Image view area
(approx.):
Supplied by master station.
370mA (max.) 4.5mA (Standby, approximate)
CCD camera
In horizontal position:
When pan-and-tilted:
Vertical
18"
3'
Horizontal
26"
6'
Min. illumination:
Ambient temperature:
Wiring:
Less than 1 Lux (at 20" from camera).
14° F ~ 140° F.
2 parallel wires, non-polarized to master. PE Insulated, low capacitance.
Use Aiphone wire # 871802
Wiring distance:
AWG
Distnace
Dimensions: (HxWxD)
Mounting:
10-3/16" x 7-5/16" x 5/8" (outer panel dimensions)
Flush mount: 9-1/16" x 6-1/8" x 2-11/16" (ABS plastic back box is included)
Surface mount with SBX-DGV: 10-3/8" x 7-7/16" x 3-¼” (top), 2-½” (bottom)
Weight (approx.):
1.90lbs
22AWG
165'
18AWG
330'
FCC Class B Verification
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device , pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try and correct the interference by one or more of the following measures:
— Reorient or locate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
Note:
Only information pertaining to the connection and operation of the MK-DGV and devices interfacing with it are
included here. For complete installation, wiring, and operational information about the MK system, please refer
to the Installation Manual included with the monitor.
Aiphone Communication Systems
1700 130th Ave. N.E.
Bellevue, WA 98005
(425) 455-0510
FAX (425) 455-0071
Toll Free Technical Support:
1-800-692-0200
FAX: 1-800-832-3765
E-mail tech-serv@aiphone.com
Pg. 3
MK-DGV instr.
1005JD
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising