2N Helios IP FORCE deurintercoms

2N Helios IP FORCE deurintercoms
2N® Helios IP Force
Security IP Intercom
Installation Manual
Version
2.3
www.2n.cz
The 2N TELEKOMUNIKACE a.s. is a Czech manufacturer and supplier of telecommunications
equipment.
The product family developed by 2N TELEKOMUNIKACE a.s. includes GSM gateways, private
branch exchanges (PBX), and door and lift communicators. 2N TELEKOMUNIKACE a.s. has
been ranked among the Czech top companies for years and represented a symbol of
stability and prosperity on the telecommunications market for almost two decades. At
present, we export our products into over 120 countries worldwide and have exclusive
distributors on all continents.
2N® is a registered trademark of 2N TELEKOMUNIKACE a.s. Any product and/or other
names mentioned herein are registered trademarks and/or trademarks or brands protected
by law.
2N TELEKOMUNIKACE a.s. administers the FAQ database to help you quickly find
information and to answer your questions about 2N products and services. On
www.faq.2n.cz you can find information regarding products adjustment and instructions for
optimum use and procedures „What to do if...“.
2N TELEKOMUNIKACE a.s. hereby declares that the 2N® Helios IP Force product complies
with all basic requirements and other relevant provisions of the 1999/5/EC directive. For
the full wording of the Declaration of Conformity see the CD-ROM (if enclosed) or our
website at www.2n.cz.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
The 2N TELEKOMUNIKACE a.s. is the holder of the ISO 9001:2009 certificate. All
development, production and distribution processes of the company are managed by this
standard and guarantee a high quality, technical level and professional aspect of all our
products.
Content
Content
1. Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.1 Components and Associated Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.2 Terms and Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2. Description and Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 20
2.1 Before You Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
2.2 Mechanical Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
2.3 Electric Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
2.4 Extending Module Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
2.5 Button Tags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
3. Function and Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
3.1 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
3.2 Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
3.3 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
4. Technical Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
5. Supplementary Information . . . . . . . . . . . . . . . . . . . . . . . . . . 75
5.1 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
5.2 Directives, Laws and Regulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
5.3 General Instructions and Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
1. Product Overview
Here is what you can find in this section:
1.1 Components and Associated Products
1.2 Terms and Symbols
Basic Features
2N® Helios IP Force is a highly resistant and reliable IP door access intercom
provided with a lot of useful above-standard functions. Supporting the SIP standard
and being compatible with the leading IP PBX and telephone suppliers, 2N® Helios IP
Force can make use of all VoIP services. 2N® Helios IP Force can work as a standard
or emergency door access intercom for buildings, entrances to premises or garages,
manufacturing halls, highways and so on.
2N® Helios IP Force is equipped with two very sensitive microphones and an up to
10W loudspeaker. Thanks to an integrated acoustic echo cancelling (AEC) system, the
product provides mutual audibility even of persons talking at the same time under
normal conditions.
2N® Helios IP Force can be equipped with a colour wide-angle camera, which
displays the calling person on the called party's video telephone or PC monitor.
2N® Helios IP Force can be provided with 1, 2 or 4 pre-programmed buttons. You
can set up to three telephone numbers and time profiles for each of the buttons to
increase the accessibility of the called party.
2N® Helios IP Force can be equipped with a numerical keypad to be used as a code
lock for lock switch activating or telephone/subscriber number dialling.
2N® Helios IP Force is equipped with an electric lock switch. You can control the
switch using a numerical keypad or, during a call, using any telephone set. An
additional switch module can be installed if necessary. A wide range of settings allow
for a variety of applications.
2N® TELEKOMUNIKACE a.s., www.2n.cz
4
2N® Helios IP Force can also be provided with RFID card reader modules.
2N® Helios IP Force is very easy to install. All you have to do is connect the system
into your LAN via a network cable and feed it from a 12 V power supply or your PoE
supporting LAN.
Configure 2N® Helios IP Force using your PC via any web browser. Use the IP
Manager to manage extensive 2N® Helios IP Force systems easily and quickly.
Advantages of Use
Uncompromising Antivandal design
High coverage level – up to class IP69K
Variable mounting options (brick/plasterboard flush mounting, surface mounting)
Sensitive microphone and powerful loudspeaker
Bidirectional communication – acoustic echo cancelling
Integrated colour camera with wide-angle lens
Optional dial buttons including name tags and backlight
Optional numerical keypad with backlight
Integrated electronic lock switches with wide setting options
Optional integrated RFID card reader module
LAN (PoE) or external 12 V power supply
Configuration via web interface or dedicated PC application
SIP 2.0 support
Up to 1999 telephone directory positions
Up to 20 user time profiles
Video codecs (H.263, H.263+, H.264, MPEG-4, JPEG)
Audio codecs (G.711, G.729, G.722, L16/16kHz)
HTTP server for configuration
SNTP client for time synchronisation with server
RTSP server for video streaming
SMTP client for e-mail sending
TFTP client for automatic configuration and firmware update
2N® TELEKOMUNIKACE a.s., www.2n.cz
5
1.1 Components and Associated Products
2N® Helios IP Force Components and Associated Products:
2N® TELEKOMUNIKACE a.s., www.2n.cz
6
Basic Units
Part No. 9151101C
Part No. 9151101
1 button
1 button
camera
control of two electric locks
control of two electric locks
possibility of connecting
additional switch
possibility of connecting
additional switch
2N® TELEKOMUNIKACE a.s., www.2n.cz
Part No. 9151101W
IP69K
1 button
10 W loudspeaker
extra robust version
control of two electric locks
possibility of connecting
additional switch
7
Part No. 9151101CW
IP69K
1 button
camera
10 W loudspeaker
extra robust version
control of two electric locks
Part No. 9151104C
Part No. 9151104
4 buttons
4 buttons
camera
control of two electric locks
control of two electric locks
possibility of connecting
additional switch
possibility of connecting
additional switch
possibility of connecting
additional switch
Part No. 9151104CW
Part No. 9151104W
Part No. 9151101K
10 W loudspeaker, IP69K
10 W loudspeaker, IP69K
1 button
4 buttons
4 buttons
keypad
camera
control of two electric locks
control of two electric locks
control of two electric locks
possibility of connecting
additional switch
2N® TELEKOMUNIKACE a.s., www.2n.cz
possibility of connecting
additional switch
possibility of connecting
additional switch
8
Part No. 9151101CKW
Part No. 9151101CK
10 W loudspeaker, IP69K
1 button
1 button
keypad
keypad
camera
camera
control of two electric locks
control of two electric locks
possibility of connecting
additional switch
2N® TELEKOMUNIKACE a.s., www.2n.cz
possibility of connecting
additional switch
9
Part No. 9151101KW
10 W loudspeaker,
Part No. 9151102CR
Part No. 9151102R
IP69K
2 buttons
1 button
possibility of connecting
card reader
keypad
control of two electric locks
possibility of connecting
additional switch
2 buttons
camera
possibility of connecting
card reader
control of two electric locks
control of two electric locks
possibility of connecting
additional switch
possibility of connecting
additional switch
Part No. 9151102CRW
10 W loudspeaker,
IP69K
2 buttons
Part No. 9151101CRP
Part No. 915101RP
1 button, pictograms,
1 button, pictograms,
with camera,
camera
possibility of connecting
card reader
possibility of connecting
card reader
control of two electric locks
control of two electric locks
possibility of connecting
additional switch
possibility of connecting
additional switch
2N® TELEKOMUNIKACE a.s., www.2n.cz
possibility of connecting
card reader
control of two electric locks
possibility of connecting
additional switch
10
2N® Helios IP Force is designed for outdoor applications and requires no additional
roof. W-including Part Nos. are intended for WAP pressure cleaning and extremely
noisy environments (such as highways, etc.).
All 2N® Helios IP Force units can be flush or wall mounted without requiring any
additional accessories. Use the appropriate mounting box (see below) for plasterboard
and hollow brick flush mounting.
Flush Mounting Box
Part No. 9151001
Brick flush mounting box
Dimension: 132 x 223 x 83 mm
2N® TELEKOMUNIKACE a.s., www.2n.cz
Part No. 9151002
Plasterboard flush mounting box
Dimension: 237 x 129 x 70 mm
Hole: 237 x 118 mm
11
Internal Units
Part No. 91378365
Part No. 91378365WH
2N® Indoor Touch black
2N® Indoor Touch white
The elegant internal touch
The elegant internal touch
®
panel, 2N Indoor Touch panel, 2N® Indoor Touch
, is suitable for all 2N®
, is suitable for all 2N®
Helios IP intercoms. On
Helios IP intercoms. On
the panel’s display not only the panel’s display not only
can you find out who is at
can you find out who is at
the door, but also start a
the door, but also start a
conversation with the
conversation with the
visitor, open the lock or
visitor, open the lock or
turn on the light in the
turn on the light in the
entrance hall.
entrance hall.
Part No. 91378366
Part No. 91378367
Part No. 91378368
2N® Indoor Touch black
2N® Indoor Touch black
2N® Indoor Touch black
WiFi
WiFi + NFC
NFC
The elegant internal touch
The elegant internal touch
The elegant internal touch
®
®
panel, 2N Indoor Touch panel, 2N Indoor Touch panel, 2N® Indoor Touch
, is suitable for all 2N®
, is suitable for all 2N®
, is suitable for all 2N®
Helios IP intercoms. On
Helios IP intercoms. On
Helios IP intercoms. On
the panel’s display not only the panel’s display not only the panel’s display not only
can you find out who is at
can you find out who is at
can you find out who is at
the door, but also start a
the door, but also start a
the door, but also start a
conversation with the
conversation with the
conversation with the
visitor, open the lock or
visitor, open the lock or
visitor, open the lock or
turn on the light in the
turn on the light in the
turn on the light in the
entrance hall.
entrance hall.
entrance hall.
2N® TELEKOMUNIKACE a.s., www.2n.cz
12
VoIP Telephones
Part No. 91378357
Grandstream GXV3240 VoIP video
telephone
GXV3240 is the successor to the popular
GXV3140 model, which allows comfortable
video calls in the IP network. Touchscreen
and keyboard control.
Part No. 91378358
Grandstream GXV3275 VoIP telephone
GXV3275 is the successor to the
popular GXV3175 model, which allows
comfortable video calls in the IP
network. Touchscreen control.
Electric Locks
Part No. 932070E
BEFO 1211
12 V / 600 mA
Part No. 932080E
BEFO 1221 with momentum
pin
Part No. 932090E
BEFO 1211MB with
mechanical blocking
12V / 600 mA
12V / 600 mA
For opening of the lock a
short electrical impuls is
sufficient, which unlocks the
lock. Lock is then open until
someone closes the door.
Enables mechanically close or
open the lock. When opened,
the lock is open all the time.
When closed, it behaves as
standart electrical lock.
Tip
FAQ: Electric locks - Difference between locks in 2N® Helios IP accesories
2N® TELEKOMUNIKACE a.s., www.2n.cz
13
Power Supply
Part. No. 91378100
PoE injector - without cable
Part. No. 91378100E
PoE injector - with EU cable
Part. No. 91378100US
PoE injector - with US cable
Part No. 91341481E
Adapter 12 V / 2 A
Stabilised 12 V / 2 A power
supply needs to be used
when no PoE is available.
Part No. 932928
12 V transformer
For external power
supply of the lock
with 12V AC voltage.
For power supply of intercom
viaethernet cable when PoE
switch is not available.
2N® TELEKOMUNIKACE a.s., www.2n.cz
14
Additional Modules
Part No. 9151010
Additional switch with
normally open/closed
contact and 12 V
switched output.
Includes tamper
switch.
Part No. 9151011
Includes tamper switch.
Part No. 9151016
Includes tamper switch.
Internal RFID card reader 1
25 kHz for installation in 2N Internal RFID card reader 13.5
® Helios IP Force interco
6 MHz for installation in 2N®
ms. Allows the use of
Helios IP Force intercoms.
EM4100, EM4102 and HID Allows the use of Mifare, iClass,
Enables control of a
Proximity cards. Another
DESFire and other standards.
secondary device,
two switches, two logical
Two switches, two logical inputs
passive time unlimited
inputs and a Wiegand
and a Wiegand interface are
switching up to 48 V / interface are available. It is available. It is compatible with
2 A or active switch
compatible with the 2N®
the 2N® Helios IP Force two12 V / 700 mA. Also
Helios IP Force two-butto
button and pictogram models.
includes tamper
n and pictogram models. It
It also includes a security
switch to signal
also includes a security
switch to signal when the front
opening of the front
switch to signal when the
panel is opened.
panel.
front panel is opened.
Part No. 9159010
Security Relay
A handy add-on that
Part No. 9151017
significantly enhances door
Internal RFID card
entry security as it prevents
reader 13.56 MHz NFC
tampering with the
for 2N® Helios IP
intercom and forced
Force mounting.
opening of the lock. To be
installed between intercom
and lock, powered by the
intercom.
2N® TELEKOMUNIKACE a.s., www.2n.cz
Part No. 9159011
Wiegand Isolator
The 2N® Helios IP Wiegand I
solator is designed for galvanic
isolation of two devices
separately power supplied and
interconnected via the Wiegand
bus. The 2N® Helios IP Wiega
nd Isolator protects the
interconnected devices against
communication errors and/or
damage.
15
Part No. 9137410E
External IP Relay - 1
output
Part No. 9137411E
External IP Relay - 4
outputs, PoE
Standalone IP device
which can be
Standalone IP device which
controlled by HTTP co can be controlled by HTTP c
mmands sent by
ommands sent by Helios IP
Helios IP intercom,
intercom, which can thus
which can thus control control devices on unlimited
devices on unlimited
distance.
distance.
Part No. 9137420E
External RFID card reader
for connection to a PC using
Part No. 9134166E
a USB interface. Suitable
RFID key fob, 125 kHz
for system management
and the addition of EM41xx
cards via the PC application,
2N® Helios IP Manager.
2N® TELEKOMUNIKACE a.s., www.2n.cz
Part No. 9134165E
RFID card, 125 kHz
EM4100
Part No. 9159050
Induction Loop
16
Part No. 9159014EU/US/UK
2N® 2Wire
(set of 2 adaptors and power
source for EU/US/UK)
Part No. 9134173
Mifare RFID card,
13.56 MHz
Part No. 9134174
Mifare RFID card, 13.56
MHz
The 2N® 2Wire converter
allows you to use existing
wiring (2 wires) from your
original door bell or door
intercom to connect any IP
device. You don’t have to
configure anything, and you
only need one 2N® 2Wire unit
at each end of the cable and a
power source connected to at
least one of these units. The
2N® 2Wire unit then provides
PoE power not only to the
second converter, but also to
all other connected IP end
devices.
Part No. 9159012
Part No. 9159013
Exit button
(suitable for Internal
RFID card reader or
Security relay)
A button for
connection to a logic
input for opening a
door inside a building.
2N® TELEKOMUNIKACE a.s., www.2n.cz
Magnetic door contact
(suitable for Internal RFID
card reader)
Set for installation on a
door, enabling the status of
door opening to be
ascertained. Used when the
intercom is used for door
protection, to detect when
the door is not closed or
forced open.
Part No. 9159030
External RFID card reader, 125
kHz
Secondary reader for
connection to an internal
reader. Allows control of card
entry from both sides of the
door. IP67 cover, also suitable
for exteriors. Reads EM4100
and EM4102 cards.
17
Part No. 9154004
Water-proof metal
button
(suitable for Internal
RFID card reader)
Tip
For more accessories and particular advice please contact your local
distributor of 2N products.
Tip
FAQ: Induction loop - How to connect it with 2N® Helios IP
2N® TELEKOMUNIKACE a.s., www.2n.cz
18
1.2 Terms and Symbols
The following symbols and pictograms are used in the manual:
Safety
Always abide by this information to prevent persons from injury.
Warning
Always abide by this information to prevent damage to the device.
Caution
Important information for system functionality.
Tip
Useful information for quick and efficient functionality.
Note
Routines or advice for efficient use of the device.
2N® TELEKOMUNIKACE a.s., www.2n.cz
19
2. Description and Installation
Here is what you can find in this section:
2.1
2.2
2.3
2.4
2.5
Before You Start
Mechanical Installation
Electric Installation
Extending Module Connection
Button Tags
2N® TELEKOMUNIKACE a.s., www.2n.cz
20
2.1 Before You Start
Product Completeness Check
Before you start please check the contents of your 2N® Helios IP Force delivery:
1× 2N® Helios IP Force
1× frame (of the corresponding colour)
1× Torx 10 / Torx 20 double-ended wrench
Bushings (enclosed):
1× big two-hole sealed bushing with nut
1× spare sealing for big bushing for a thick cable, one hole
1× big blank with nut
1× small bushing with nut
1× bushing plug, big size
2× bushing plugs, small size
1× 2N® Helios IP Force Installation Manual
1× mounting template
1× A5 transparent name plate foil
1× spare name tag
4× (5 × 90) mm screws
4× "intelligent" (8 × 50) mm dowels
2N® TELEKOMUNIKACE a.s., www.2n.cz
21
2.2 Mechanical Installation
Mounting Type Overview
Refer below for a list of mounting types and necessary components.
Flush Mounting – Classic Bricks
What You Need:
A precisely cut hole or, optionally, the brick flush mounting
box, Part No. 9151001
Hole: (132 × 223 × 83) mm (with flush mounting box)
Hole: (112 × 220 × 70) mm (without flush mounting box)
Flush Mounting – Thermally Insulated Wall
What You Need:
Longer screws (depending on the thermal insulation
thickness)
Hole: (112 × 220 × 70) mm
Flush Mounting – Hollow Bricks
What You Need:
Brick flush mounting box, Part No. 9151001
Hole: (132 × 223 × 83) mm
Flush Mounting – Plasterboard Wall
What You Need:
Plasterboard flush mounting box, Part No. 9151002
Hole: 118 × 235mm
2N® TELEKOMUNIKACE a.s., www.2n.cz
22
Wall Mounting (concrete and steel structures, entry barrier columns,
etc.)
What You Need:
Just your 2N® Helios IP Force unit
Caution
The warranty does not apply to the product defects and failures arisen as
a result of improper mounting (in contradiction herewith). The
manufacturer is neither liable for damages caused by theft within an area
that is accessible after the attached electric lock is switched. The product
is not designed as a burglar protection device except when used in
combination with a standard lock, which has the security function.
When the proper mounting instructions are not met, water might get in
and destroy the electronics. It is because the intercom circuits are under
continuous voltage and water infiltration causes an electro-chemical
reaction. The manufacturer's warranty shall be void for products damaged
in this way!
Common Mounting Principles
Tip
Select flush mounting where possible to make your product elegant
looking, more vandal resistant and more secure.
You can purchase the flush mounting box in advance and hire an
installation professional to make the basic installation work. Moreover, the
mounting box helps you align the intercom vertically (with a deviation of
up to 2°).
Caution
Make sure that the dowel holes have the required diameter. If the
diameter is too large, the dowels may get loose. Use some suitable
building adhesive to keep the dowels in place.
Make sure that the hole depth is sufficient too! The dowel length is 50 mm
and the screw length is 90 mm.
Remember that dowels of poor quality may easily get loose and fall out of
the wall!
Stainless steel screws are used for the 2N® Helios IP Force assembly.
Other screws than stainless steel ones corrode soon and may aesthetically
deteriorate the surrounding environment!
Having removed the front panel, make sure that no dirt gets inside the
product (especially onto the sealing surface and microphone sound
guides).
2N® TELEKOMUNIKACE a.s., www.2n.cz
23
Note
The microphone sound guides are normally loose after the front panel is
removed! The screw is only used as a fall-out protection during
installation.
2N® TELEKOMUNIKACE a.s., www.2n.cz
24
Flush Mounting – Classic Bricks
If you use the brick flush mounting box, follow the instructions included in the box. If
you do not use the mounting box, follow the instructions below:
1. Make a hole using the template. Suppose
that all the required cables have been
carried into the hole.
2. Unpack the frame, put the intercom inside
and place the set onto the hole to make
sure that the hole is deep enough and the
uneven edge is perfectly covered with the
frame.
3. Make sure that the dowel holes are drilled
accurately! You will not be able to align
considerable inaccuracies with this way of
mounting! Push or hammer the enclosed
dowels into the drilled holes. Use some
suitable building adhesive if the dowels
are too loose.
4. Remove the front panel from the
intercom.
5. Select the holes for cable supply. Insert
the blanks into the other holes. Apply the
cable bushings or a suitable sealant to
prevent penetration of insects or water.
You can also insert the small bushing in
the intercom bottom hole.
6. Put the frame on the intercom.
7. Place the intercom into the hole while
introducing the cables. Leave some of the
cables inside the unit as a reserve and the
rest under the intercom bottom.
8. Insert the enclosed screws in the lateral
mounting holes making sure they have
penetrated into the dowels. Tighten all
the screws properly. Tip: The screw
tightening sequence may affect the
intercom position.
9. We recommend to seal the frame – wall
gap with a silicone or another sealant to
avoid wall dampening as a result of water
leakage.
10. Do not complete mounting until you have
finished electrical installation.
Be sure keep strictly the hole dimensions while mounting the device into classic bricks
without the flush mounting box as shown in the figure below.
2N® TELEKOMUNIKACE a.s., www.2n.cz
25
2N® TELEKOMUNIKACE a.s., www.2n.cz
26
Flush Mounting – Thermally Insulated Wall
Cut out the thermal insulation layer using the template (the same as for classic brick
wall).
Caution
The hole depth depends on the insulation layer thickness. If the insulation
layer is rather thick, you may need longer screws! If there are hollow
bricks under the insulation, make sure that your screws pass through the
whole dowel (50 mm) and fix the dowel reliably.
Make sure that the dowel holes have the required diameter. If the
diameter is too large, the dowels may get loose. Use some suitable
building adhesive to keep the dowels in place.
Make sure that the hole depth is sufficient too! The dowel length is 50 mm
and the screw length is 90 mm.
Suppose that all the required cables have been carried into the drilled hole. Now follow
the instructions applicable for classic brick flush mounting. However, remember that
thermally insulated walls show less strength than classic brick walls.
Flush Mounting – Plasterboard
Use the plasterboard flush mounting box and follow the instructions included therein.
2N® TELEKOMUNIKACE a.s., www.2n.cz
27
Flush Mounting – Hollow Bricks
Suppose you intend to install your 2N® Helios IP Force unit into a wall made of
hollow bricks. Note that the external side of the bricks gets damaged by cutting and
the dowels cannot practically be fixed into the thin internal part of the bricks.
Therefore, use the brick flush mounting box and follow the instructions included
therein.
Wall Mounting
Wall (surface) mounting is used where flush mounting is inapplicable (in concrete and
steel structures, entry barrier columns, etc.). The frame is not used.
Caution
Wall mounting may be a problem where vandals may destroy the unit (in
public garages, e.g.). Therefore, use steel fixing elements instead of the
dowels and screws included in the delivery.
Be sure to insert plugs into unused bushing holes to avoid water leakage
during facade cleaning, for example. Never leave the holes open for even
a short time (one day delay between mounting and cable connection,
e.g.).
2N® TELEKOMUNIKACE a.s., www.2n.cz
28
Warning
Eliminate the risk of accident! Wall mounting is not suitable for narrow
passages or places where people's attention may be distracted. The
manufacturer shall not be liable for injuries incurred as a result of unsafe
mounting!
1. Select position with respect to the supply
cables. Where the cables are installed
inside a structure or wall, use the hole at
the intercom bottom.
2. Drill holes of the depth of 70 mm for
dowels in the wall as shown in the figure.
Push or hammer the enclosed dowels into
the drilled holes. Use some suitable
building adhesive if the dowels are too
loose. Use fixing elements of your own for
steel structure surface mounting (metric
screws + nuts, e.g.).
3. Remove the front panel from the
intercom.
4. Select the holes for cable supply. Select
and mount the bushings depending on the
cables: 2-hole bushing or 1-hole bushing
or both. Insert the blanks in the other
holes.
5. Put the intercom on the wall/structure
while introducing cables inside. Leave
some of the cables inside the unit as a
reserve. Insert the plugs in the unused
bushings and tighten the bushing nuts
carefully.
6. Do not complete mounting until you have
finished electrical installation. Where
cables lead along the surface, use the
bushings included in the delivery.
Use of Cable Bushings
The cable bushings included in the 2N® Helios IP Force delivery are designed for
the following cables:
Big bushing: for two cables of the diameter of 5–6 mm (UTP cable), or, upon
insert replacement, for one thick cable/tube of the diameter of up to 14 mm.
Small bushing: for one cable of the diameter of 5–8 mm.
Tip
Even a LAN cable including the RJ-45 connector can go through the big
bushing. See below for instructions.
2N® TELEKOMUNIKACE a.s., www.2n.cz
29
How to Pull a RJ-45 Terminated Cable through a Bushing
1. Unscrew the big bushing nut completely.
2. Remove the sealing including the cover from the bushing. Cut either of the
components as shown in the figures.
3. Put the bushing nut on the cable and insert the sealing.
4. Replace the cover onto the sealing.
5. Pull the cable connector though the bushing body into the intercom and clip it into
the motherboard connector.
2N® TELEKOMUNIKACE a.s., www.2n.cz
30
6. Move the sealing including the cover along the cable as far as the bushing body, or
add a plug if necessary.
7. Replace and tighten the nut.
2N® TELEKOMUNIKACE a.s., www.2n.cz
31
2.3 Electric Installation
This subsection describes how to connect 2N® Helios IP Force into your Local Area
Network (LAN) and how to connect supply voltage and the electric lock.
PCB Connectors
Picture shows the lay-out of connectors on the 2N® Helios IP Force printed circuit
board (PCB). Cables, accessories and other system components are connected to
connectors X1 through X22.
Connectors description:
X1 – Loudspeaker
X2 – Button 2
X3 – Button 3
X4 – Camera module
X5 – Button 1
SW1 – Reset button (555v3 version only)
X6 – Configuration jumpers
X7 – Induction loop output
X8 – Extending module (RFID card reader or additional switch)
X10 – Buttons 1 through 4
X11 – LAN
X12 – Servicing connector
X13 – Keypad module
X15 – Left-hand microphone
X16 – Right-hand microphone
X17 – Relay NO and NC contact max. 30 V / 1 A AC/DC
X18 – Switched output 9 up to 13 V DC depending on power supply (PoE: 9 V;
adaptor: power supply voltage minus 1 V), max 700 mA
X19 – Power input 12 V ±15 % / 2 A DC
LED1/2 – System status indicators
LED3 – LAN connection activity indicator
2N® TELEKOMUNIKACE a.s., www.2n.cz
32
Figure: 2N® Helios IP Force Connectors, PCB Version 555v2
2N® TELEKOMUNIKACE a.s., www.2n.cz
33
Figure: 2N® Helios IP Force Connectors, PCB Version 555v3
2N® TELEKOMUNIKACE a.s., www.2n.cz
34
Figure: 2N® Helios IP Force Connectors, PCB Version 555v4
LAN Connection
2N® Helios IP Force is connected to the LAN via a RJ-45 terminated (connector X11)
UTP/STP cable (of category Cat 5e or higher). The system is equipped with the
Auto-MDIX function and so both the straight and crossed cable versions can be used.
External Power Supply Connection
2N® Helios IP Force can be fed either from an external 12 V ±15 % / 2 A DC power
supply or from the LAN equipped with the PoE 802.3af supporting network elements.
External Power Supply
An external 12 V power supply is connected to terminal block X19. Use a 12 V ± 15 %
DC power source dimensioned to current intake of 2 A at least (Part No. 91341481E) to
ensure a reliable function of your device.
2N® TELEKOMUNIKACE a.s., www.2n.cz
35
PoE Supply
2N® Helios IP Force is compatible with the PoE 802.3af (Class 0 – 12.95 W)
technology and can be supplied directly from the LAN via compatible network elements.
If your LAN in incompatible, insert the PoE injector, Part No. 91378100E/US, between
2N® Helios IP Force and the nearest network element.
Electric Lock Connection
2N® Helios IP Force is equipped with an electrically isolated relay switch with NO and
NC contacts (terminal block X17, max. 30 V / 1 A AC/DC ) and 9 up to 13 V
DC depending on power supply (PoE: 9 V; adaptor: power supply voltage minus 1 V),
max 700 mA switched output (terminal block X18), to which a standard electric lock or
another compatible electrical appliance can be connected.
Note
Devices with PCB version 555v3 and higher provides independent control
of 12 V switched output (terminal block X18) and relay switch (terminal
block X17). Devices with PCB version 555v2 have both outputs switched
simultaneously.
Factory Default Resetting (PCB version 555v3)
For resetting device to default settings press and hold SW1 button. Wait for the first
sound signalization and then release the button. If you press the button for short time
device will reboot only. SW1 button is available in devices with PCB version 555v3 and
higher. For devices with PCB version 555v2 see procedure below.
Factory Default Resetting (PCB version 555v2)
1. Disconnect the device from the power supply.
2. Move the short-circuit jumper on connector X6 into the Default setup position.
Configuration jumpers (X6) are located in the right-hand upper corner of the
PCB.
3. Reconnect the power supply and wait for a start signalling sound.
4. Disconnect the device from the power supply.
5. Move the short-circuit jumper on connector X6 into the Normal operation
position.
6. Reconnect the power supply. The device will be reset to factory default.
2N® TELEKOMUNIKACE a.s., www.2n.cz
36
Normal operation
Default setup
Figure: Configuration jumpers X6, PCB version 555v2
Mounting Completion
1. Having connected all the wires, make sure that the bushings, if used, are
tightened properly and the RJ-45 connector is inserted in the PCB connector.
2. Replace the front cover carefully. Make sure that the connector is inserted
correctly and the wires inside the device leave enough space for the board if you
are installing a four-button board. Tighten the four screws thoroughly with the
wrench enclosed (Torx 20) to make the panel fit tightly to the metal chassis.
Caution
Properly installed intercom is waterproof. An incorrect mounting may
compromise the intercom watertightness. Water leakage may damage the
electronic part of the system.
Stainless steel screws are used for the 2N® Helios IP Force assembly.
Other screws than stainless steel ones corrode soon and may aesthetically
deteriorate the surrounding environment!
2N® TELEKOMUNIKACE a.s., www.2n.cz
37
Available Switches
Location
Name
Relay 1
Basic Unit
Additional
Switch*
(Part
No. 9151010)
Internal RFID
Card Reader
125 kHz*
(Part
No. 9151011)
Internal RFID
Card Reader
13.56 MHz*
(Part
No. 9151016)
Description
Passive relay switch: NO and NC contacts, up to 30 V
/ 1 A AC/DC
Active switch output: 9 up to 13 V DC depending on
Output 1 power supply (PoE: 9 V; adaptor: power supply voltage
minus 1 V), max 700 mA
Passive relay switch: NO and NC contacts, up to 30 V
/ 1 A AC/DC
Active switch output: 9 up to 13 V DC depending on
Output 2 power supply (PoE: 9 V; adaptor: power supply voltage
minus 1 V), max 700 mA
Relay 1
Passive relay switch: NO and NC contacts, up to 30 V
(Card
Reader), / 1 A AC/DC
Relay 2
Output 1
(Card
Reader)
Relay 1
(Card
Reader),
Active switch output: 9 up to 13 V DC depending on
power supply (PoE: 9 V; adaptor: power supply voltage
minus 1 V), max 700 mA
Passive relay switch: NO and NC contacts, up to 30 V
/ 1 A AC/DC
Output 1 Active switch output: 9 up to 13 V DC depending on
(Card
power supply (PoE: 9 V; adaptor: power supply voltage
Reader) minus 1 V), max 700 mA
Only one module marked by * can be used.
2N® TELEKOMUNIKACE a.s., www.2n.cz
38
2.4 Extending Module Connection
2N® Helios IP Force allows to connect following extending modules:
Additional Switch
Internal RFID Card Reader 125 kHz
Internal RFID Card Reader 13.56 MHz
Security Relay
Wiegand Isolator
Additional Switch
The Additional Switch (Part No. 9151010) is used for extending the number of
outputs. This extending module is intended for mounting into the 2N® Helios IP
Force main unit and is compatible with the basic units with Part No. 915110xxxxx. If
the Additional Switch is installed, it is not possible to install Internal RFID Card Reader.
Function:
The 2N® Helios IP Force Additional Switch adds two additional switches and a
tamper switch to the 2N® Helios IP Force basic unit. The purpose of the tamper
switch is to signal any unauthorised opening of the intercom (to prevent a theft, e.g.).
It is recommended to use the tamper switch.
Tip
FAQ: Tamper switch - How to install it into the 2N® Helios IP Force
Specifications:
Passive switch: NO and NC contacts, up to 30 V / 1 A AC/DC
Active switch output: 9 V (Using PoE) or power supply voltage minus 1 V, from 9
to 13 V max. 700 mA DC
Tamper switch: 24 V / 50 mA AC/DC
2N® TELEKOMUNIKACE a.s., www.2n.cz
39
Module mounting:
1. Switch off the intercom.
2. Remove the front panel from the intercom.
3. According to your model
a. If you are mounting the switch into a two-nameplate model, demount the
button PCB (1) and remove the right-hand bottom spacer (there are four
PCB fitting spacers altogether).
b. If you are mounting the switch into a keypad model, take the keypad out of
the holder. Demount the right-hand keypad holder - beam with a pin (8) –
remembering its position. Demount the right-hand bottom spacer. Do not
disconnect the keypad cable!
c. If you are mounting the switch into a model other than the two ones
mentioned in items 3a and 3b above, remove the right-hand bottom screw
from the main board.
4. Now screw the enclosed 12 mm spacer (5) into the vacated main board slot.
5. Mount the enclosed plastic support (6) onto the switch board bottom side.
6. Put the switch board (4) in the main board connector making sure that the screw
hole is directly above the spacer.
7. According to your model
a. If you are mounting the switch into a two-nameplate model, fit the switch
board with the enclosed 10.5 mm spacer (3) and reinstall the button PCB
(1).
b. If you are mounting the switch into a keypad model, reinstall the beam (8)
of the keypad holder (the slot is on top). Insert the enclosed 4.5 mm
washer (9) between the beam and the switch board, fitting the assembly
with the 15 mm screw enclosed (7).
c. If you are mounting the switch into a model other than the two ones
mentioned in items 7a and 7b, fit the switch board with the original 6 mm
screw (2).
8. If you want to use the tamper switch, insert the tamper board (9) in the
connector located in the right-hand bottom part of the switch board (4). As the
tamper switch shares the relay output (NO and NC) terminals, you cannot use
the RELAY2 output with the tamper switch together.
9. Place front panel back and tighten all four screws.
2N® TELEKOMUNIKACE a.s., www.2n.cz
40
2N® TELEKOMUNIKACE a.s., www.2n.cz
41
2N® TELEKOMUNIKACE a.s., www.2n.cz
42
Module settings:
Refer to the 2N® Helios IP Configuration Manual for details.
Connection:
Internal RFID Card Reader 125 kHz
The Internal RFID Card Reader 125 kHz (Part No. 9151011) is used for reading
RFID card Ids in the 125 kHz band. This module is intended for mounting into the 2N®
Helios IP Force model 9151102CR, 9151102R, 9151101CRP and 9151101RP. These
models have an window, which is necessary for antenna operation. If the Internal RFID
Card Reader is installed, it is not possible to install the Additional Switch.
Function:
The 2N® Helios IP Force Internal RFID Card Reader adds two logical inputs, two
additional switches and a tamper switch to the 2N® Helios IP Force basic unit.
The purpose of the tamper switch is to signal any unauthorised opening of the intercom
(to prevent a theft, e.g.). It is recommended to use the tamper switch.
2N® TELEKOMUNIKACE a.s., www.2n.cz
43
Tip
FAQ: Tamper switch - How to install it into the 2N® Helios IP Force
Specifications:
Card reader
Compatible with EM4100 / EM4102 / HID® Prox RFID cards
Operating frequency: 125 KHz
Minimum reading distance: 10 mm above 2N® Helios IP Force cover
Relay output
Switching contact
30 V / 2A AC/DC
Active output
12 V / 700 mA transistor switched output
Logical inputs
Active mode – requires external voltage (JP2 jumper OFF)
UIN-ON = min +2.5 V
UIN-OFF = max +1.5 V
UIN max = +48 V
IIN (UIN +48 V) = max 1 mA
Passive mode – requires external contact only (JP2 jumper ON)
UOUT = approx. 8.3 V
ILOOP = approx. 0.5 mA
Signalling output
Internal red LED under reader window
WIEGAND interface
Off/Input/Output (as programmed)
2N® TELEKOMUNIKACE a.s., www.2n.cz
44
Mounting guide:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
Switch off the intercom.
Remove the front panel (7) from the intercom.
Mount antenna board (8). Use two enclosed self tapping screws (9).
Plug enclosed cable (11) to the antenna board connector.
Demount a button PCB (1). Don't disconnect its cable!
There will stay four spacers after the switch board removal. Dismount the bottom
right one.
There are two short metal spacers enclosed to the reader. Take a longer one (5),
12 mm long. Screw it into the free hole.
Plug an enclosed plastic support (6) to the reader board from the bottom side.
Put the reader board (4) in the main board connector making sure that the
mounting hole is directly above the spacer.
Screw in a remaining metal spacer (3), 10.5 mm long.
Fit the button PCB (1) back to its position using original bolts (2).
If you want to use the tamper switch (to detect unauthorized opening the case,
as a theft protection), insert the tamper board (10) in the connector located in
the right-hand bottom part of the reader board (4). As the tamper switch shares
the relay output (NO and NC) terminals, you cannot use the RELAY2 output with
the tamper switch at the same time.
Plug the antenna cable (11) to its connector at the reader board (4).
Place front panel back and tighten all four screws.
2N® TELEKOMUNIKACE a.s., www.2n.cz
45
2N® TELEKOMUNIKACE a.s., www.2n.cz
46
2N® TELEKOMUNIKACE a.s., www.2n.cz
47
2N® TELEKOMUNIKACE a.s., www.2n.cz
48
Module setting:
Refer to the 2N® Helios IP Configuration Manual for details of Wiegand, outputs
and reader. Refer to the 2N® Helios IP Automation manual for details of input, red
LED and tamper function and use.
Connection:
2N® TELEKOMUNIKACE a.s., www.2n.cz
49
Internal RFID Card Reader 13.56 MHz
The Internal RFID Card Reader 13.56 MHz (Part No. 9151016) is used for reading
RFID card Ids in the 13.56 MHz band. This module is intended for mounting into the
2N® Helios IP Force model 9151102CR, 9151102R, 9151101CRP and 9151101RP.
These models have an window, which is necessary for antenna operation. If
the Internal RFID Card Reader is installed, it is not possible to install the Additional
Switch.
Function:
The 2N® Helios IP Force Internal RFID Card Reader adds two logical inputs, two
additional switches and a tamper switch to the 2N® Helios IP Force basic unit.
The purpose of the tamper switch is to signal any unauthorised opening of the intercom
(to prevent a theft, e.g.). It is recommended to use the tamper switch.
Tip
FAQ: Tamper switch - How to install it into the 2N® Helios IP Force
Specifications:
Card reader
Operating frequency: 13.56 MHz
Minimum reading distance: 30 mm above 2N® Helios IP Force cover
Compatible with cards
ISO14443A - Mifare Classic 1k & 4k, DESFire EV1, Mini, Plus S&X,
SmartMX, Ultralight, Ultralight C, SLE44R35, my-d move (SLE66Rxx),
PayPass, Legic Advant
ISO1443B - Calypso, CEPAS, Moneo, SRI512, SRT512, SRI4K, SRIX4K,
PicoPass, HID iCLASS
ISO18092/NFC - NFCIP-1: Active and passive communication mode, NFC
Forum Tag Type 1–4, Sony FeliCa
Relay output
Switching contact
30 V / 2A AC/DC
2N® TELEKOMUNIKACE a.s., www.2n.cz
50
Active output
9 to 12 V / 700 mA transistor switched output. Depends on power supply (PoE: 9
V or power supply voltage minus 1 V).
Logical inputs
Active mode – requires external voltage (JP2 jumper OFF)
UIN-ON = min +2.5 V
UIN-OFF = max +1.5 V
UIN max = +48 V
IIN (UIN +48 V) = max 1 mA
Passive mode – requires external contact only (JP2 jumper ON)
UIN1 = approx. 8.3 V
UIN2 = approx. 8.3 V
ILOOP = approx. 0.5 mA
Signalling output
Internal red LED under reader window
PWR
For external RFID card reader
Out: 9 to 12 V / 350 mA depends on power supply
WIEGAND interface
Off/Input/Output (as programmed)
2N® TELEKOMUNIKACE a.s., www.2n.cz
51
Mounting guide:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
Switch off the intercom.
Remove the front panel (7) from the intercom.
Mount antenna board (8). Use two enclosed self tapping screws (9).
Plug enclosed cable (11) to the antenna board connector.
Demount a button PCB (1). Don't disconnect its cable!
There will stay four spacers after the switch board removal. Dismount the bottom
right one.
There are two short metal spacers enclosed to the reader. Take a longer one (5),
12 mm long. Screw it into the free hole.
Plug an enclosed plastic support (6) to the reader board from the bottom side.
Put the reader board (4) in the main board connector making sure that the
mounting hole is directly above the spacer.
Screw in a remaining metal spacer (3), 10.5 mm long.
Fit the button PCB (1) back to its position using original bolts (2).
If you want to use the tamper switch (to detect unauthorized opening the case,
as a theft protection), insert the tamper board (10) in the connector located in
the right-hand bottom part of the reader board (4). As the tamper switch shares
the relay output (NO and NC) terminals, you cannot use the RELAY2 output with
the tamper switch at the same time.
Plug the antenna cable (11) to its connector at the reader board (4).
Place front panel back and tighten all four screws.
2N® TELEKOMUNIKACE a.s., www.2n.cz
52
2N® TELEKOMUNIKACE a.s., www.2n.cz
53
2N® TELEKOMUNIKACE a.s., www.2n.cz
54
2N® TELEKOMUNIKACE a.s., www.2n.cz
55
Module setting:
Refer to the 2N® Helios IP Configuration Manual for details of Wiegand, outputs
and reader. Refer to the 2N® Helios IP Automation manual for details of input, red
LED and tamper function and use.
Connection:
2N® TELEKOMUNIKACE a.s., www.2n.cz
56
Security Relay
The Security Relay (Part No. 9159010) is used for enhancing security between the
intercom and the connected electric lock. The 2N® Helios IP Security Relay is
designed for any 2N® Helios IP intercom model with firmware versions 1.15 and
higher. It significantly enhances security of the connected electric lock as it prevents
lock opening by forced intercom tampering.
Function:
The 2N® Helios IP Security Relay is a device installed between an intercom (outside
the secured area) and the electric lock (inside the secured area). The 2N® Helios IP
Security Relay includes a relay that can only be activated if the valid opening code is
received from the intercom.
Specifications:
Passive switch: NO and NC contacts, up to 30 V / 1 A AC/DC
Active switch output: 9 to 12 V / 700 mA transistor switched output. Depends on
power supply (PoE: 9 V or power supply voltage minus 1 V).
Dimensions: (56 × 31 × 24) mm
Weight: 20 g
Installation:
Install the 2N® Helios IP Security Relay onto a two-wire cable between the intercom
and the electric lock inside the area to be secured (typically behind the door). The
device is powered and controlled via this two-wire cable and so can be added to an
existing installation. Thanks to its compact dimensions, the device can be installed into
a standard mounting box.
Connection:
Connect the 2N® Helios IP Security Relay to the intercom as follows:
To the intercom active output (OUT1 or OUT2) , or
To the intercom relay output with a 12 V DC serial external power supply.
Connect the electric lock to the 2N® Helios IP Security Relay output as follows:
To the active 12 V / 700 mA DC output, or
To the relay output with a serial external power supply.
2N® TELEKOMUNIKACE a.s., www.2n.cz
57
The device also supports a Departure button connected between the ‘PB’ and ‘HeliosIP’ terminals. Press the Departure button to activate the output for 5 seconds.
Status signalling:
Green LED
blinking
on
blinking
on
Red LED
off
off
blinking
blinking
Status
Operational mode
Activated output
Programming mode – waiting for initialisation
Error - wrong code received
Configuration:
Connect the 2N® Helios IP Security Relay to the properly set intercom switch
output; refer to the 2N® Helios IP Configuration Manual. Make sure that one
LED at least on the 2N® Helios IP Security Relay is on or blinking.
Press and hold the 2N® Helios IP Security Relay Reset button for 5 seconds to
put the device in the programming mode (both the red and green LEDs are
blinking).
Activate the intercom switch using the keypad, telephone, etc. The first code sent
from the intercom will be stored in the memory and considered valid. After code
initialisation, the 2N® Helios IP Security Relay will pass into the operational
mode (the green LED is blinking).
Tip
FAQ: 2N® Helios IP Security Relay – what it is and how to use it with 2N ®
Helios IP intercom?
Tip
Video Tutorial: Door intercoms 2N® Helios IP - Security Relay
2N® TELEKOMUNIKACE a.s., www.2n.cz
58
Connection:
Wiegand Isolator
The Wiegand Isolator (Part No. 9159011) is usef for galvanic isolation of the
Wiegand bus.
The 2N® Helios IP Wiegand Isolator is designed for galvanic isolation of two
devices with separate power supply and interconnected via the Wiegand bus. The 2N®
Helios IP Wiegand Isolator protects the interconnected devices against
communication errors and/or damage.
Connection of the 2N® Helios IP Card Reader to a security system unit is a typical
example of application.
Function:
The 2N® Helios IP Wiegand Isolator separates galvanically a two-wire Wiegand bus
in one direction and a status LED signal in the other direction. The module is power
supplied from the Wiegand bus receiver side.
2N® TELEKOMUNIKACE a.s., www.2n.cz
59
Specifications:
2-wire WIEGAND IN
2-wire WIEGAND OUT
LED IN switched against GND on WIEGAND OUT side
Open LED OUT switched against GND on WIEGAND IN side (up to 24 V / 50 mA)
5 to 16V / 10 mA power supply from Wiegand bus receiver side
500 V DC isolation strength
Connection:
2N® TELEKOMUNIKACE a.s., www.2n.cz
60
2N® TELEKOMUNIKACE a.s., www.2n.cz
61
2.5 Button Tags
This subsection describes work with Button Tags in 2N® Helios IP Force .
Tag Printing
1. Every 2N® Helios IP Force delivery includes a sheet of translucent foil, which
can be laser-printed. Cut the printed foil and insert the tags in the name plates.
2. Every name plate includes a piece of foil, which can be written over manually,
using a waterproof permanent marker, if necessary.
Note
Always use waterproof foil (enclosed or other) for the tags. Never use
paper or ink jet printing to avoid damage due to water leakage!
Tip
A template for printing nametags can be downloaded from www.2n.cz.
Tag Inserting/Replacing Instructions
2N® Helios IP Force provides an intuitive, easy access to the name
plates. The tags are easy to insert and replace even without a
manual. You need not remove the front panel and thus are not
exposed to the risk of loss of components while replacing the tags.
1. Loosen the name plate screw using the wrench enclosed, for
example. You can open the name plate window like a door
without losing the tightened screw.
2. Remove the used or blank name tag and insert a new tag.
3. Close the name plate window and tighten the screw
appropriately.
4. Check the click effect of the buttons: if the button fails to click
properly when pressed (when moved by approx. 0.5 mm), the
tag is too thick or thin. Make sure that the button clicks when
you press it on both ends.
2N® TELEKOMUNIKACE a.s., www.2n.cz
62
3. Function and Use
In this section we describe the basic and extending functions of the 2N® Helios IP
Force product.
Here is what you can find in this section:
3.1 Configuration
3.2 Control
3.3 Maintenance
2N® TELEKOMUNIKACE a.s., www.2n.cz
63
3.1 Configuration
Use a PC equipped with any web browser to configure 2N® Helios IP Force :
Launch your web browser (Internet Explorer, Firefox, etc.).
Enter the IP address of your intercom (http://192.168.1.100/, e.g.).
Log in using the Admin user name and 2n password.
You have to know the IP address of your device to log in to the integrated web server.
By default, 2N® Helios IP Force is switched into the dynamic IP address mode, i.e. it
obtains the IP address automatically if a properly set DHCP server is available in your
LAN. If no such DHCP server is available, you can operate 2N® Helios IP Force in the
static IP address mode.
If your device remains inaccessible (you have forgotten the IP address, or the LAN
configuration has changed, for example), change the LAN settings using the buttons on
the device.
IP Address Retrieval
Take the following steps to retrieve the 2N® Helios IP Force IP address:
Connect (or, if connected, disconnect and reconnect) 2N® Helios IP Force to
the power supply.
Wait for the second sound signal
.
Press the first quick dial button 5 times.
2N® Helios IP Force will read its IP address.
If the address is 0.0.0.0, it means that the intercom has not obtained the IP
address from the DHCP server.
Note
Be sure to press the button sequence within thirty seconds after the
sound signal for security reasons. Up to 2 s intervals are allowed between
the presses.
2N® TELEKOMUNIKACE a.s., www.2n.cz
64
Static IP Address Setting for 4-button models
Follow the instructions below to enable the static IP address mode:
Connect 2N® Helios IP Force to the power supply (or, disconnect and
reconnect it if already connected).
Wait for the first acoustic signal
.
Press buttons 1, 1, 1, 2, 2, 3 sequentially.
The acoustic signal
indicates mode switching.
Wait until the device is restarted automatically.
Caution
The 1, 1, 1, 2, 2, 3 sequence must be entered within 30 seconds after the
first sound signal for security reasons. The inter-digit delay may be 2 s at
most.
The device will have the following network parameters after restart:
IP address – 192.168.1.100
Network mask – 255.255.255.0
Default gateway – 192.168.1.1
Dynamic IP Address Setting for 4-button models
Follow the instructions below to enable automatic getting of network parameters from
the DHCP server:
Connect 2N® Helios IP Force to the power supply (or, disconnect and
reconnect it if already connected).
Wait for the first acoustic signal
Press buttons 2, 1, 1, 2, 2, 3 sequentially.
2N® TELEKOMUNIKACE a.s., www.2n.cz
65
The acoustic signal
indicates mode switching.
Wait until the device is restarted automatically.
Caution
The 2, 1, 1, 2, 2, 3 sequence must be entered within 30 seconds after the
first sound signal for security reasons. The inter-digit delay may be 2 s at
most.
2N® Helios IP Force gets the IP address upon restart only if the DHCP server is
configured properly.
Mode Switching with 1 or 2-Button Models
In case your 2N® Helios IP Force device is equipped with 1 or 2 buttons, you can
switch the modes using one button only.
Connect 2N® Helios IP Force to the power supply (or, disconnect and
reconnect it if already connected).
Wait for the first acoustic signal
.
Press the first quick dial button 15 times.
The acoustic signal
indicates mode switching.
Wait until the device is restarted automatically.
2N® TELEKOMUNIKACE a.s., www.2n.cz
66
Caution
The 15 times 1 sequence must be entered within 30 seconds after the first
sound signal for security reasons. The inter-digit delay may be 2 s at
most.
The static IP address mode will be switched into the dynamic IP address mode and vice
versa upon restart.
2N® TELEKOMUNIKACE a.s., www.2n.cz
67
3.2 Control
This subsection describes how to control 2N® Helios IP Force when viewed by an
external user.
Speed Dial Buttons
Press the speed dial buttons on the basic unit to make quick dialling for the first 1, 2 or
4 positions (depending on the model type) in the telephone directory. Call setup is
signalled by a long intermittent tone or otherwise as configured in the PBX connected.
Repeated pressing of one and the same speed dial button during call setup may initiate
call termination, or call termination plus dialling the next telephone number of the
called subscriber, or may be assigned no function. This behaviour can be set in unit
configuration.
If your model is equipped with a numerical keypad, you can also push the
anytime to terminate a call if enabled so in the Hang up with # parameter.
button
Calling to Telephone Directory Positions
The 2N ® Helios IP Force telephone directory can contain up to 1999
pre-programmed positions. Speed dial can only be used for positions 1 to 4. The
remaining positions can be retrieved via the numerical keypad if the Speed dial using
digits function is enabled in configuration.
Procedure:
Enter the position number using your numerical keypad (05, 15, 200, 1759 e.g. –
two digits at least and four digits at most) and press
for confirmation.
You can also push the
button anytime to terminate a call if enabled so in the
Hang up with # parameter in the unit configuration.
Calling to Telephone Number
You can dial a telephone number using your numerical keypad from 2N® Helios IP
Force if the Enable telephone function parameter is on.
Procedure:
1. Press the
button.
2. You will hear the continuous tone from the loudspeaker.
3. Enter the telephone number using the numerical keypad and repress
confirmation.
for
4. You can also push the
button anytime to terminate a call if enabled so in the
Hang up with # parameter; refer to the Miscellaneous subsection.
2N® TELEKOMUNIKACE a.s., www.2n.cz
68
Answering and Rejecting Incoming Calls
If the automatic incoming call answering function is off, 2N® Helios IP Force signals
an incoming call with loud ringing. Push the
button to answer the call and the
to
reject the call. This function is available in models equipped with a numerical keypad
only.
Door Opening (Switch Activation) by Code
2N® Helios IP Force is equipped with a door lock opening switch. Enter the valid code
using your numerical keypad to activate the switch.
Procedure:
Enter the numerical switch activating code using the numerical keypad and press
for confirmation.
A successful entering of a valid code is signalled by a continuous tone indicating
unlocking (switch activation). An invalid code is signalled acoustically by
.
User/Profile Activation and Deactivation
Activate/deactivate a user or a profile using the numerical keypad in order to define
call routing to the telephone directory numbers more specifically.
Procedure:
Enter the numerical user activating/deactivating code and press
confirmation.
for
A successful entering of a valid code is signalled acoustically by
for
profile) for activation, or
is signalled acoustically by
2N® TELEKOMUNIKACE a.s., www.2n.cz
(
(
for profile) for deactivation. An invalid code
.
69
3.3 Maintenance
Cleaning
If used frequently, 2N® Helios IP Force gets dirty. To clean it, use a piece of soft
cloth moistened with clean water. We recommend you to obey the following principles
while cleaning:
Never use aggressive detergents (such as abrasives or strong disinfectants).
Use suitable cleaning agents for glass lens cleaning (cleaners for glasses, optic
devices screens, etc.).
Alcohol-based cleaners may be applied.
Clean the device in dry weather in order to make waste water evaporate quickly.
Tip
The 2N® Helios IP Force models of Part Nos. 9151101W and 9151101C
W may be cleaned with WAP high pressure washers.
Future Tag Replacement, Programming Changes
For necessary steps refer to the preceding subsections. Keep the following for future
changes:
This manual
Unused transparent foil strips for button tags
Caution
Always use the product for the purpose it was designed and manufactured
for, in compliance herewith.
The manufacturer reserves the right to modify the product in order to
improve its qualities.
2N® Helios IP Force contains no environmentally harmful components.
When the product's service life is exhausted and you would like to dispose
of it please do so in accordance with applicable legal regulations.
2N® TELEKOMUNIKACE a.s., www.2n.cz
70
4. Technical Parameters
Signalling protocol
SIP (UDP, TCP, TLS)
Buttons
Button design: Transparent, white backlit buttons with easily replaceable name
tags
Count of buttons: 1, 2 or 4
Numerical keypad: optional
Audio
Microphone: 2 integrated microphones
Amplifier: 10 W (class D)
Loudspeaker: 1 W (optionally 10 W)
Volume control: Adjustable with automatic adaptive mode
Full duplex: Yes (AEC)
Audio stream
Protocols: RTP / RTSP
Codecs: G.711, G.729, G.722, L16/16kHz
2N® TELEKOMUNIKACE a.s., www.2n.cz
71
Camera
Sensor: 1/4'' colour CMOS
Resolution: 640 (H) × 480 (V)
Picture frequency: Up to 30 snaps/s
Sensitivity: 1.9 V/lux-sec (550 nm)
Viewing angle: 135° (H), 109° (V)
Infrared illumination: Yes
Focal length: 1.1 mm
Focal length HD version: 2.3 mm
Video stream
Protocols: RTP / RTSP / HTTP
Codecs: H.263, H.263+, H.264, MPEG-4, M-JPEG
IP camera function: Yes
2N® TELEKOMUNIKACE a.s., www.2n.cz
72
Interface
Power supply: 12 V ±15 % / 2 A DC or PoE
PoE: PoE 802.3af (Class 0 - 12.95 W)
LAN: 10/100BASE-TX s Auto-MDIX, RJ-45
Recommended cabling: Cat-5e or higher
Passive relay switch: NO and NC contacts, up to 30 V / 1 A AC/DC
Active switch output: 9 up to 13 V DC depending on power supply (PoE: 9 V;
adaptor: power supply voltage minus 1 V), max 700 mA
RFID card reader
Optional
Includes besides card reader itself: Wiegand interface, tamper switch,
active output, relay, two inputs
Supported cards on 125 kHz version, Part No. 9151011
EM4100, EM4102, HID Prox
Supported cards on 13.56 MHz version, Part No. 9151016 (only card serial
number is read)
ISO14443A
Mifare Classic 1k & 4k, DESFire EV1, Mini, Plus S&X, SmartMX,
Ultralight,
Ultralight C, SLE44R35, my-d move (SLE66Rxx), PayPass, Legic
Advant
ISO14443B
Calypso, CEPAS, Moneo, SRI512, SRT512, SRI4K, SRIX4K, PicoPass,
HID iCLASS
Supported cards on 13.56 MHz NFC version, Part No. 9151017 (only card
serial number is read)
ISO14443A
Mifare Classic 1k & 4k, DESFire EV1, Mini, Plus S&X, SmartMX,
Ultralight,
Ultralight C, SLE44R35, my-d move (SLE66Rxx), PayPass, Legic
Advant
ISO14443B
Calypso, CEPAS, Moneo, SRI512, SRT512, SRI4K, SRIX4K, PicoPass,
HID iCLASS
NFC
SmartPhone with NFC/HCE support, since Android version 4.3
Wiegand Interface: Input/Output mode, located on RFID card reader module
Active switch output: 9 up to 13 V DC depending on power supply (PoE: 9 V;
adaptor: power supply voltage minus 1 V), max 700 mA
Passive relay switch: NO and NC contacts, up to 30 V / 1 A AC/DC
Additional switch
Optional: Includes also tamper switch
Active switch output: 9 up to 13 V DC depending on power supply (PoE: 9 V;
adaptor: power supply voltage minus 1 V), max 700 mA
Passive relay switch: NO and NC contacts, up to 30 V / 1 A AC/DC
2N® TELEKOMUNIKACE a.s., www.2n.cz
73
Mechanical properties
Cover: Robust aluminium cast product, front panel: aluminium cast, fiberglass
FR4 (91511xxxR)
Working temperature: −40 °C to 55 °C
Working relative humidity: 10 % – 95 % (non-condensing)
Storing temperature: −40 °C to 70 °C
Dimensions
217 × 109 × 83 mm
242 × 136 × 83 mm incl. frame
Weight: netto max. 2 kg / brutto max. 2,5 kg
Covering level: IP65, IP69K (91511xxxW)
2N® TELEKOMUNIKACE a.s., www.2n.cz
74
5. Supplementary Information
Here is what you can find in this section:
5.1 Troubleshooting
5.2 Directives, Laws and Regulations
5.3 General Instructions and Cautions
2N® TELEKOMUNIKACE a.s., www.2n.cz
75
5.1 Troubleshooting
For the most frequently asked questions refer to faq.2n.cz.
2N® TELEKOMUNIKACE a.s., www.2n.cz
76
5.2 Directives, Laws and Regulations
Europe
2N® Helios IP Force conforms to the following directives and regulations:
Directive 1999/5/EC of the European Parliament and of the Council, of 9 March 1999 –
on radio equipment and telecommunications terminal equipment and the mutual
recognition of their conformity
Directive 2006/95/EC of the European Parliament and of the Council of 12 December
2006 on the harmonisation of the laws of Member States relating to electrical
equipment designed for use within certain voltage limits
Directive 2004/108/EC of the Council of 15 December 2004 on the harmonisation of
the laws of Member States relating to electromagnetic compatibility
Commission Regulation (EC) No. 1275/2008, of 17 December 2008, implementing
Directive 2005/32/EC of the European Parliament and of the Council with regard to
ecodesign requirements for standby and off mode electric power consumption of
electrical and electronic household and office equipment
Directive 2011/65/EU of the European Parliament and of the Council of 8 June 2011 on
the restriction of the use of certain hazardous substances in electrical and electronic
equipment
Regulation (EC) No. 1907/2006 of the European Parliament and of the Council of 18
December 2006 concerning the Registration, Evaluation, Authorisation and Restriction
of Chemicals (REACH), establishing a European Chemicals Agency, amending Directive
1999/45/EC and repealing Council Regulation (EEC) No. 793/93 and Commission
Regulation (EC) No. 1488/94 as well as Council Directive 76/769/EEC and Commission
Directives 91/155/EEC, 93/67/EEC, 93/105/EC and 2000/21/EC
Directive 2012/19/EC of the European Parliament and of the Council of 4 July 2012 on
waste electrical and electronic equipment.
Industry Canada
This Class B digital apparatus complies with Canadian ICES-003. / Cet appareil
numérique de la classe B est conforme a la norme NMB-003 du Canada.
2N® TELEKOMUNIKACE a.s., www.2n.cz
77
FCC
NOTE: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user's authority to operate this equipment.
2N® TELEKOMUNIKACE a.s., www.2n.cz
78
5.3 General Instructions and Cautions
Please read this User Manual carefully before using the product. Follow all instructions
and recommendations included herein.
Any use of the product that is in contradiction with the instructions provided herein
may result in malfunction, damage or destruction of the product.
The manufacturer shall not be liable and responsible for any damage incurred as a
result of a use of the product other than that included herein, namely undue application
and disobedience of the recommendations and warnings in contradiction herewith.
Any use or connection of the product other than those included herein shall be
considered undue and the manufacturer shall not be liable for any consequences arisen
as a result of such misconduct.
Moreover, the manufacturer shall not be liable for any damage or destruction of the
product incurred as a result of misplacement, incompetent installation and/or undue
operation and use of the product in contradiction herewith.
The manufacturer assumes no responsibility for any malfunction, damage or
destruction of the product caused by incompetent replacement of parts or due to the
use of reproduction parts or components.
The manufacturer shall not be liable and responsible for any loss or damage incurred as
a result of a natural disaster or any other unfavourable natural condition.
The manufacturer shall not be held liable for any damage of the product arising during
the shipping thereof.
The manufacturer shall not make any warrant with regard to data loss or damage.
The manufacturer shall not be liable and responsible for any direct or indirect damage
incurred as a result of a use of the product in contradiction herewith or a failure of the
product due to a use in contradiction herewith.
All applicable legal regulations concerning the product installation and use as well as
provisions of technical standards on electric installations have to be obeyed. The
manufacturer shall not be liable and responsible for damage or destruction of the
product or damage incurred by the consumer in case the product is used and handled
contrary to the said regulations and provisions.
The consumer shall, at its own expense, obtain software protection of the product. The
manufacturer shall not be held liable and responsible for any damage incurred as a
result of the use of deficient or substandard security software.
The consumer shall, without delay, change the access password for the product after
installation. The manufacturer shall not be held liable or responsible for any damage
incurred by the consumer in connection with the use of the original password.
The manufacturer also assumes no responsibility for additional costs incurred by the
consumer as a result of making calls using a line with an increased tariff.
2N® TELEKOMUNIKACE a.s., www.2n.cz
79
Electric Waste and Used Battery Pack Handling
Do not place used electric devices and battery packs into municipal waste containers.
An undue disposal thereof might impair the environment!
Deliver your expired electric appliances and battery packs removed from them to
dedicated dumpsites or containers or give them back to the dealer or manufacturer for
environmental-friendly disposal. The dealer or manufacturer shall take the product
back free of charge and without requiring another purchase. Make sure that the devices
to be disposed of are complete.
Do not throw battery packs into fire. Battery packs may not be taken into parts or
short-circuited either.
2N® TELEKOMUNIKACE a.s., www.2n.cz
80
2N TELEKOMUNIKACE a.s.
Modřanská 621, 143 01 Prague 4, Czech Republic
Phone: +420 261 301 500, Fax: +420 261 301 599
E-mail: sales@2n.cz
Web: www.2n.cz
EN2065_v2.0.3
2N® TELEKOMUNIKACE a.s., www.2n.cz
81
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising