Data Sheet: IUL

Data Sheet: IUL
HELIPORTS
IUL-L
LED In-pavement Utility & Heliport
Perimeter Light
Compliance with Standards
FAA:
Manufactured to applicable L-852T(L) requirements in
FAA AC 150/5345-46 (Current Edition) and the FAA
Engineering Brief No. 67.
8-inch
Ordering Code
Uses
• Heliports with constant voltage sources
- Yellow for military and existing civilian applications
- Green for new civilian applications
- Used as boundary marking of final approach and takeoff
(FATO) areas, touchdown and lift-off (TLOF) areas, and
aprons
- Also used for taxiway edges and aiming points
• Gate security
• Under vehicle inspection illumination
• Used for a variety of special applications where a balance of
vertical and horizontal light output is required
• Provides essential lighting for the protection of fixed installations and other potential targets
• Used in high security areas to assist detection of bombs and
smuggling, in maintenance facilities to spot vehicle damage,
and to protect entrances to security areas
• Fixture layout/quantity can be designed for individual and/or
pattern control to enable use of alternate traffic patterns
12-inch
IUL-
LED Color
1 = White
2 = Yellow
3 = Green
4 = Blue
5 = Red
Mounting
1 = 12-inch fixture for L-868 light base
2 = 12-inch fixture for L-867 light base
3 = 8-inch fixture for 8-inch light base
Light Beam Direction
1 = Upward light pattern
2 = Omnidirectional light pattern1
Arctic Option
0 = Without arctic option
1 = With arctic option2
Notes
Fixture supplied with only L-823 style male connector. To ensure
wire entry is waterproof, a secondary connector kit (Part No.
70A0046) is required for installation.
1
Heliport light pattern
2
When powered by a parallel circuit, heater is designed for use
at only 120 VAC, ±10%, 50/60 Hz
Features
• Operates over a wide input voltage range of 95-264 VAC, 50/60 Hz
Features (Continued)
• Light output stays constant regardless of input voltage level
• LED photometric performance will be maintained longer due to
a cleaner lens. The lower temperature of the lens prevents the
“baking effect” that causes contaminants to stick to the surface
of the lens.
• Average LED life of 100,000 hours
• Low profile – < 0.25 inch above ground, which reduces vibrations caused by vehicles, increasing fixture life
• IUL with arctic option (U.S. Patent 7192155 B2) uses a thermostatically controlled heater to prevent ice and snow buildup
from obscuring light output. Melts ice similar to traditional
incandescent fixtures.
• No batteries to replace – Constant, dependable level of light at
all times, comparable to FAA-specified medium intensity light
levels
• Integral third-wire grounding for fixture and installation base
cans
• Thermostatically controlled heater cycles on and off when
temperature drops below freezing, reducing overall energy
consumption
• Standard FAA-Style L-823 connectors provide a complete
environmental seal, eliminating fluid “siphoning” up wiring to
fixture interior
• High strength – Rugged, proven design - fixture originally
designed to withstand the rollover weight of large aircraft in
airport movement areas
• Equivalent mechanical and electrical design has been field
tested in thousands of airfield installations
• Offers longer maintenance intervals and requires fewer spare
parts, resulting in lower life cycle costs
• Designed and built with simplicity and ease of maintenance in
mind
• Can be provided with a shallow mounting base designed for inpavement installation
I-2
2073 Rev. P I Manual No. 96A0364
• Aluminum alloy cover, inner cover, and optical assembly, stainless steel hardware, and a hardened optical glass lens
• Fixture is also available for series circuits. Contact the ADB
Sales Department or see ADB catalog sheet 2060.
HELIPORTS
IUL-L I LED In-pavement Utility & Heliport Perimeter Light
Operating Conditions
Spare Components
Temperature: -40 °C to +55 °C (-40 °F to +131 °F)
Description
Part No.
Altitude: Sea level to 10,000 feet (3000 m)
Cord set
Inner pan assembly, 95-264 V, yellow
Inner pan assembly, 95-264 V, blue
Inner pan assembly, 95-264 V, green, white
LED optical assembly, white, omnidirectional
light pattern, w/out heater
LED optical assembly, white, omnidirectional
light pattern, with heater
LED optical assembly, yellow, omnidirectional
light pattern, w/out heater
LED optical assembly, yellow, omnidirectional
light pattern, with heater
LED optical assembly, green, omnidirectional
light pattern, w/out heater
LED optical assembly, green, omnidirectional
light pattern, with heater
LED optical assembly, blue, omnidirectional
light pattern, w/out heater
LED optical assembly, blue, omnidirectional
light pattern, with heater
LED optical assembly, red, omnidirectional
light pattern, w/out heater
LED optical assembly, red, omnidirectional
light pattern, with heater
LED optical assembly, white, upward light
light pattern, w/out heater
LED optical assembly, white, upward light
pattern, with heater
Lens gasket, molded
O-ring, inner cover seal
Prism lens
Secondary female connector kit
Top cover, 8-inch
Top cover, 12-inch, L-868 11.25” bolt circle
Top cover, 12-inch, L-867 10.25” bolt circle
73A0136-23
44A6354-10
44A6354-20
44A6354-30
44A7217-10
Relative Humidity: Up to 100%
8-inch Load Bearing Base Can
Part Number
88ICC05Y
Electrical Supply
Input voltage
W/out Heater
With Heater
95 VAC (min.) - 264 VAC (max.),
50/60 Hz
120 VAC, ±10%, 50/60 Hz
Maximum Input Power
W/out Heater
With Heater
Yellow
10.2 VA
33.2 VA
Green
14.3 VA
37.3 VA
Blue
13.5 VA
36.5 VA
White
14.3 VA
37.3 VA
Red
14.3 VA
37.3 VA
Energy Cost Savings
LED Fixture Load
Incan./Tungsten
Halogen Load
Energy Savings
Yellow, Voltage Driven, Without/Inactive Heater
10.2 VA
40/54 VA
3.9/5.3 times
Yellow, Voltage Driven, without Heater Active
33.2 VA
1
40/54 VA
1.2/1.6 times
44A7217-11
44A7217-20
44A7217-21
44A7217-30
44A7217-31
44A7217-40
44A7217-41
44A7217-50
44A7217-51
44A7217-60
44A7217-61
4071.76.041
7080.90.335
63A1071
70A0046
4071.76.002
62A2157-1
62A2157-2
Either a 40 W (VA) or 54 W (VA) lamp is in typical equivalent
fixtures
Packaging
Dimensions
8-inch Fixture
8-inch Fixture
Outside diameter:
Bolt-circle diameter:
8.43 in (21.4 cm)
7.32 in (18.6 cm)
In cardboard box:
6 x 10 x 10 in (15.24 x 25.4 x 25.4 cm)
Weight with packing:
7.65 lb (3.47 kg)
Weight without packing: 5.65 lb (2.56 kg)
12-inch Fixture
8-inch Base Can
Outside diameter:
Bolt-circle diameter (L-868B):
Bolt-circle diameter (L-867B):
11.94 in (30.33 cm)
11.25 in (28.58 cm)
10.25 in (26.04 cm)
Solar Lighting System Design
Weight:
3.95 lb (1.79 kg)
12-inch Fixture
In cardboard box:
7 x 13 x 13 in (17.8 x 33 x 33 cm)
Weight with packing:
15.3 lb (6.94 kg)
Weight without packing: 12.3 lb (5.58 kg)
ADB can design a complete solar-powered heliport package for
interested customers to include solar equipment, elevated and
in-pavement fixtures, obstruction lights, wind cone, and control
equipment. Call 614-573-8232 for more information.
ADB Airfield Solutions
Leuvensesteenweg 585
B-1930 Zaventem
Belgium
ADB Airfield Solutions, LLC
977 Gahanna Parkway
Columbus, OH 43230
USA
Telephone: +32 (0)2 722.17.11
www.adb-air.com
Telephone: +1 614.861.1304
+1 800.545.4157
© ADB Airfield Solutions
All rights reserved
Product specifications may be subject to change,
and specifications listed here are not binding.
Confirm current specifications at time of order.
2073 Rev. P I Manual No. 96A0364
I-3
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising